L-1797-A

O W N E R ' S M A N U A L

For the latest product updates and setup tips:

Visit us on the web!www.brinly.com

MODEL:

DT-401BH

Important: This manual contains information for the safety of persons and property. Read it carefully before assembly and

operation of the equipment!

● Assembly● Installation● Operation● Repair Parts

D E T H A T C H E R

The limited warranty set forth below is given by Brinly-Hardy Company with respect to new merchandise purchased and used in the United States, its possessions and territories.

Brinly-Hardy Company warrants the products listed below against defects in material and workmanship, and will at its option, repair or replace, free of charge, any part found to be defective in materials or workmanship. This limited warranty shall only apply if this product has been assembled, operated, and maintained in accordance with the Operator’s manual furnished with the product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water, or damage because of other peril or natural disaster.

Normal Wear Parts or components thereof are subject to separate terms as follows: All normal wear parts or component failures will be covered on the product for a period of 90 days.

Parts found to be defective within the warranty period will be replaced at our expense. Our obligation under this warranty is expressly limited to the replacement or repair, at our option, of parts found to be defective in material and workmanship.

HOW TO OBTAIN SERVICE: Warranty parts replacements are available, ONLY WITH PROOF OF PURCHASE, through our Pull Behind Accessories Customer Service Department. Call 877-728-8224.

This limited warranty does not provide coverage in the following cases:

a) Routine maintenance items such as lubricants and filters.b) Normal deterioration of the exterior finish due to use or exposure.c) Transportation and/or labor charges.d) The warranty does not include commercial and/or

rental use.

No implied warranty, including any implied warranty of merchantability of fitness for a particular purpose, applies after the applicable period of express written warranty above as to the part as identified below. No other express warranty whether written or oral, except as mentioned above, given by any person or entity, including a dealer or retailer, with respect to any product, shall bind Brinly-Hardy Co. During the period of the warranty, the exclusive remedy is repair or replacement of the product as set forth above.

MANUFACTURER’S LIMITED WARRANTY FOR

Pull Behind Accessories

The provisions as set forth in this warranty provide the sole and exclusive remedy arising from the sale. Brinly-Hardy Co. shall not be liable for incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for rental expenses to temporarily replace a warranted product.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you.

During the warranty period, the exclusive remedy is replacement of the part. In no event shall recovery of any kind be greater that the amount of the purchase price of the product sold. Alteration of safety features of the product shall void this warranty. You assume the risk and liability for loss, damage, or injury to you and your property and/or to others and their property arising out of the misuse or inability to use this product.

This limited warranty shall not extend to anyone other than the original purchaser or to the person for whom it was purchased as a gift.

HOW STATE LAW RELATES TO THIS WARRANTY: This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

IMPORTANT: The Warranty period stated below begins with the PROOF OF PURCHASE. Without the proof of purchase, the Warranty period begins from the date of manufacture determined by the serial number manufacturing date.

DETHATCHER WARRANTY PERIOD:The warranty period for this dethatcher is as follows: Steel frame parts – 2 Years. Tires, wheels and tines are normal wear parts - 90 days.

Brinly-Hardy Company, 3230 Industrial Parkway, Jeffersonville, IN 47130

2.

!

!

!!

This symbol will help to point out important safety precautions throughout this manual. It means - ATTENTION!BECOME ALERT! Your safety is involved.

!

CONGRATULATIONS on your new Brinly-Hardy Dethatcher! Your dethatcher has been designed, engineered and manufactured to give you the best possible dependability and performance.

Should you experience any problem you can not easily remedy, please do not hesitate to contact our knowledgeable customer service department toll-free at 1-877-728-8224. We have competent, well trained technicians to help you with the assembly and use of your dethatcher.

CUSTOMER RESPONSIBILITIES

Read and observe the “RULES FOR SAFE OPERATION”. These instructions will enable you to assemble and maintain your dethatcher properly.

Follow a regular schedule in maintaining, caring-for and using your Brinly-Hardy Dethatcher.

RULES FOR SAFE OPERATION.....................................2 PARTS REFERENCE ......................................................3PARTS LIST .....................................................................3ASSEMBLY ......................................................................4-8OPERATION ....................................................................9MAINTENANCE ...............................................................9

RULES FOR SAFE OPERATION

• Know your towing vehicle controls and how to stop safely, READ YOUR OWNER'S MANUAL before operating.

• Do not allow children to operate the vehicle, do not allow adults to operate the vehicle without proper instruction or without having read the owner's manual.

• Do not carry passengers. Keep children and pets at a safe distance away.

• Always wear substantial footwear. Do not wear loose fitting clothing that can get caught in moving parts.

• Keep your eyes and mind on your vehicle/attachment and area being covered. Do not let other interests distract you.

• Stay alert for holes in the terrain and other hidden hazards.

• Do not drive close to creeks, ditches and public highways.

• Watch out for traffic when crossing or near roadways.

• When using any attachment, don't allow anyone near while in operation.

• Keep the vehicle and attachment in good operating condition and keep safety devices in place.

• Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition.

• The vehicle and attachment should be stopped and inspected for damage after striking a foreign object. The damage should be repaired before restarting and operating the equipment.

OPERATING HINTS

• Never operate dethatcher without safety wires installed.

• Always disconnect dethatcher from towing vehicle when cleaning or servicing the unit.

• Do not stand or ride on dethatcher, bodily harm could result.

• Only tow your dethatcher behind vehicles for which it is designed, riders and lawn/garden tractors

• Only tow your dethatcher behind vehicles for which it was designed - riders, lawn/garden tractors. DO NOT TOW this dethatcher behind high speed equipment such as ATV's, RTV's, or Pick up trucks.

• To avoid personal injury and/or equipment damage, never exceed the speed range of 3 to 5 M. P. H.

• When backing, carefully back straight to avoid jack-knifing which could result in damage to the equipment.

This symbol will help to point out important safety precautions throughout this manual. It means - ATTENTION! BECOME ALERT! your safety is involved

L-1797-A

L-1797-AL-1797-A10. 3.

EXPLODED REFERENCE

PARTS LIST

19

21

2

12

3

9

114

18

18

18

16

2221

19

23

20

11

11

13

13

18

21

19

2119

4

154

5

6

17

21

19

8

REF PART NO DESCRIPTION QTY.NO.

1. B-5925 Decal, Logo 12. B-3861 Hitch Pin 13. D-146P Hairpin Cotter, 1/8" 14. R-616 Tine 105. R-618 Washer, Special 106. R-713-10 Tray Bracket 27. R-1541 Decal, Warning 18. B-7081-10 Wheel Mount Bracket 29. B-5182 Decal, "CE" 110. L-1744 Label, Serial No. 111. R-825 Wheel, 6 X 1.5” 212. R-892-10 Clevis 213. R-1940-10 Pull Bar 214. R-2480-10 Tine Tray 115. R-1503 Safety Wire 216. 1M1648P Bolt, Hex Hd, 1/2 x 3” 217. 10M1032P Bolt, Carriage, 5/16 x 2” 218. 11M1016P Bolt, Carriage, 5/16 x 1” 1919. 30M1000P Nut, Reg Hex, 5/16"-18 2120. 30M1600P Nut, Hex, 1/2"-13 421 40M1000P Washer, Lock 5/16" 2122. 45M1111P Washer, SAE Flat-5/16” 423. 45M1717P Washer, SAE Flat-1/2” 4

Tools Required for Assembly:

• 3/4” Wrench (1) • 1/2” Wrench (1) • Med. Adjustable Wrench (1) • Pliers

7

STOPINSTALLATION QUESTIONS?

MISSING PARTS?REPLACEMENT PARTS?

DON’T GO BACK TO THE STORE!Please call our Customer Service

Department Toll-Free at 877.728.8224

orcustomerservice

@brinly.com

To Order Parts Call:877-728-8224

Visit us on the web:www.brinly.com

10

NOTES:

L-1797-AL-1797-A4.

18Carriage Bolt, 5/16" x 1"

Qty. 10

Step 1.

1a) Install Tines (4) to Tray (14) as shown.

1b) Tighten all nuts except the one indicated.

Note: Tray dimples prevent tine rotation.

Finger tighten this nut only!

INSTALL TINES

Step 2.

Insert the Safety Wire (15) through the open coils for both the forward and aft rows of tines. Bend the Safety Wire as shown.

19Hex Nut 5/16"

Qty. 10

5Washer Qty. 10

21Lock Washer, 5/16"

Qty. 10

INSTALL SAFETY WIRE

15

5

4

21

19

14

!WARNINGFailure to install safety wires can result in personal injury if a tine should dis-engage from the tine tray.

OPERATION

Tine ACTION- Grass should be less than 3" tall for proper tine action.

When in use, all tines on the De-thatcher should deflect back and "flip" the thatch forward as shown.

If the tines seem to drag without flipping forward, the tine tray is too low and should be raised.

If all the tines stay in the free position, the tray should be lowered.

Make adjustments as necessary, up or down, by no more than 1/4" each time, until proper results are achieved.

MAINTENANCEThe key to years of trouble-free service is to keep your dethatcher clean and dry.

Occasionally check all moving parts for free movement and if necessary, lubricate with oil.

Should rust develop, sand lightly and then paint area with enamel.

Periodically check all fasteners for tightness.

!

!

9.

18

L-1797-AL-1797-A

8a) Select a smooth flat surface such as, a driveway, sidewalk, garage floor, etc.

8b) Attach your dethatcher to your towing vehicle using the Hitch Pin (2) and Hairpin Cotter.

8c. Loosen four the four nuts (19) that secure the pull bars (13) to the Tray Bracket (6).

8d) Adjust dethatcher height by placing tine tips on a 1/2” shim while ensuring that the wheels maintain contact to the flat surface.

8e) Retighten nuts (19).

18Carriage Bolt, 5/16" x 1"

Qty. 4

Step 3.

3a) Assembly Tray Bracket (6) to Pull Bar (13) with short leg facing away from pull bar. Nuts should be finger tight.

3b) Repeat for other side.

PRE-ASSEMBLE PULL BARS

19Hex Nut 5/16"

Qty. 4

22Washer, 5/16"

Qty. 4

21Lock Washer, 5/16"

Qty. 4

22

6

2119

21

19

22

13

18

18Carriage Bolt, 5/16" x 1"

Qty. 3

Step 4.

4a) Install the Pull Bars assembled in Step 3 to the Tray Assembly as shown.

Note: The Tine and Tray Bracket (6) share the same bolt on this hole only.

ASSEMBLE PULL BARS TO TRAY

19Hex Nut 5/16"

Qty. 3

21Lock Washer, 5/16"

Qty. 3

14

21

19

21

18

6

5.8.

Step 8. MOUNTING & ADJUSTMENT

3

219

1/2” Shim

13

6

Flat Surface

L-1797-AL-1797-A6.

17Carriage Bolt, 5/16" x 2"

Qty. 2

Step 5. INSTALL CLEVIS

Step 6.

6a) Insert carriage bolt (18) into Pull Bar (13) and then install Wheel Mount Bracket (8).

6b) Tighten nuts securely.

6c) Repeat for other bracket.

5a) Install Clevis (12) to Pull Bars (13). Nuts should be finger tight.

5b) Install Hitch Pin (2) and secure with Hairpin Cotter. (3).

5c. Tighten all nuts in Step 3, Step 4 and Step 5.

19Hex Nut 5/16"

Qty. 2

21Lock Washer, 5/16"

Qty. 2

INSTALL WHEEL MOUNT BRACKET

21

13 3

2

17

12

21

19

8

13

2Hitch Pin 1/2" x 2-1/2"

Qty. 1

3Hairpin Cotter 1/8"

Qty. 1

19

18

18Carriage Bolt, 5/16" x 1"

Qty. 2

19Hex Nut 5/16"

Qty. 2

21 Lock Washer, 5/16"

Qty. 2

7.

Step 7.

7a) Observe the Wheel (11). Orient the offset hub so that the offset is toward the Wheel Mount Bracket (8).

7b) Place grease on Hex Bolt (16), then pre-assemble the bolt, Flat Washer (23), wheel, Flat Washer (23) and Nut (20) as shown in Figure A.

7c) Place wheel assembly through Wheel Mount Bracket (8) install second Nut (20). Tighten securely while holding the first nut between the Wheel Assembly and Wheel Mount Bracket.

7d) Rotate Wheel and insure that it spins freely.

ASSEMBLE WHEELS

Figure A16

Hex Bolt, 1/2" x 3"Qty. 2

20Hex Nut 1/2"

Qty. 4

8

16

11

11

23

23

20

20

20

23Washer, 1/2"

Qty. 4

11

8

20

L-1797-AL-1797-A6.

17Carriage Bolt, 5/16" x 2"

Qty. 2

Step 5. INSTALL CLEVIS

Step 6.

6a) Insert carriage bolt (18) into Pull Bar (13) and then install Wheel Mount Bracket (8).

6b) Tighten nuts securely.

6c) Repeat for other bracket.

5a) Install Clevis (12) to Pull Bars (13). Nuts should be finger tight.

5b) Install Hitch Pin (2) and secure with Hairpin Cotter. (3).

5c. Tighten all nuts in Step 3, Step 4 and Step 5.

19Hex Nut 5/16"

Qty. 2

21Lock Washer, 5/16"

Qty. 2

INSTALL WHEEL MOUNT BRACKET

21

13 3

2

17

12

21

19

8

13

2Hitch Pin 1/2" x 2-1/2"

Qty. 1

3Hairpin Cotter 1/8"

Qty. 1

19

18

18Carriage Bolt, 5/16" x 1"

Qty. 2

19Hex Nut 5/16"

Qty. 2

21 Lock Washer, 5/16"

Qty. 2

7.

Step 7.

7a) Observe the Wheel (11). Orient the offset hub so that the offset is toward the Wheel Mount Bracket (8).

7b) Place grease on Hex Bolt (16), then pre-assemble the bolt, Flat Washer (23), wheel, Flat Washer (23) and Nut (20) as shown in Figure A.

7c) Place wheel assembly through Wheel Mount Bracket (8) install second Nut (20). Tighten securely while holding the first nut between the Wheel Assembly and Wheel Mount Bracket.

7d) Rotate Wheel and insure that it spins freely.

ASSEMBLE WHEELS

Figure A16

Hex Bolt, 1/2" x 3"Qty. 2

20Hex Nut 1/2"

Qty. 4

8

16

11

11

23

23

20

20

20

23Washer, 1/2"

Qty. 4

11

8

20

L-1797-AL-1797-A

8a) Select a smooth flat surface such as, a driveway, sidewalk, garage floor, etc.

8b) Attach your dethatcher to your towing vehicle using the Hitch Pin (2) and Hairpin Cotter.

8c. Loosen four the four nuts (19) that secure the pull bars (13) to the Tray Bracket (6).

8d) Adjust dethatcher height by placing tine tips on a 1/2” shim while ensuring that the wheels maintain contact to the flat surface.

8e) Retighten nuts (19).

18Carriage Bolt, 5/16" x 1"

Qty. 4

Step 3.

3a) Assembly Tray Bracket (6) to Pull Bar (13) with short leg facing away from pull bar. Nuts should be finger tight.

3b) Repeat for other side.

PRE-ASSEMBLE PULL BARS

19Hex Nut 5/16"

Qty. 4

22Washer, 5/16"

Qty. 4

21Lock Washer, 5/16"

Qty. 4

22

6

2119

21

19

22

13

18

18Carriage Bolt, 5/16" x 1"

Qty. 3

Step 4.

4a) Install the Pull Bars assembled in Step 3 to the Tray Assembly as shown.

Note: The Tine and Tray Bracket (6) share the same bolt on this hole only.

ASSEMBLE PULL BARS TO TRAY

19Hex Nut 5/16"

Qty. 3

21Lock Washer, 5/16"

Qty. 3

14

21

19

21

18

6

5.8.

Step 8. MOUNTING & ADJUSTMENT

3

219

1/2” Shim

13

6

Flat Surface

L-1797-AL-1797-A4.

18Carriage Bolt, 5/16" x 1"

Qty. 10

Step 1.

1a) Install Tines (4) to Tray (14) as shown.

1b) Tighten all nuts except the one indicated.

Note: Tray dimples prevent tine rotation.

Finger tighten this nut only!

INSTALL TINES

Step 2.

Insert the Safety Wire (15) through the open coils for both the forward and aft rows of tines. Bend the Safety Wire as shown.

19Hex Nut 5/16"

Qty. 10

5Washer Qty. 10

21Lock Washer, 5/16"

Qty. 10

INSTALL SAFETY WIRE

15

5

4

21

19

14

!WARNINGFailure to install safety wires can result in personal injury if a tine should dis-engage from the tine tray.

OPERATION

Tine ACTION- Grass should be less than 3" tall for proper tine action.

When in use, all tines on the De-thatcher should deflect back and "flip" the thatch forward as shown.

If the tines seem to drag without flipping forward, the tine tray is too low and should be raised.

If all the tines stay in the free position, the tray should be lowered.

Make adjustments as necessary, up or down, by no more than 1/4" each time, until proper results are achieved.

MAINTENANCEThe key to years of trouble-free service is to keep your dethatcher clean and dry.

Occasionally check all moving parts for free movement and if necessary, lubricate with oil.

Should rust develop, sand lightly and then paint area with enamel.

Periodically check all fasteners for tightness.

!

!

9.

18

L-1797-AL-1797-A10. 3.

EXPLODED REFERENCE

PARTS LIST

19

21

2

12

3

9

114

18

18

18

16

2221

19

23

20

11

11

13

13

18

21

19

2119

4

154

5

6

17

21

19

8

REF PART NO DESCRIPTION QTY.NO.

1. B-5925 Decal, Logo 12. B-3861 Hitch Pin 13. D-146P Hairpin Cotter, 1/8" 14. R-616 Tine 105. R-618 Washer, Special 106. R-713-10 Tray Bracket 27. R-1541 Decal, Warning 18. B-7081-10 Wheel Mount Bracket 29. B-5182 Decal, "CE" 110. L-1744 Label, Serial No. 111. R-825 Wheel, 6 X 1.5” 212. R-892-10 Clevis 213. R-1940-10 Pull Bar 214. R-2480-10 Tine Tray 115. R-1503 Safety Wire 216. 1M1648P Bolt, Hex Hd, 1/2 x 3” 217. 10M1032P Bolt, Carriage, 5/16 x 2” 218. 11M1016P Bolt, Carriage, 5/16 x 1” 1919. 30M1000P Nut, Reg Hex, 5/16"-18 2120. 30M1600P Nut, Hex, 1/2"-13 421 40M1000P Washer, Lock 5/16" 2122. 45M1111P Washer, SAE Flat-5/16” 423. 45M1717P Washer, SAE Flat-1/2” 4

Tools Required for Assembly:

• 3/4” Wrench (1) • 1/2” Wrench (1) • Med. Adjustable Wrench (1) • Pliers

7

STOPINSTALLATION QUESTIONS?

MISSING PARTS?REPLACEMENT PARTS?

DON’T GO BACK TO THE STORE!Please call our Customer Service

Department Toll-Free at 877.728.8224

orcustomerservice

@brinly.com

To Order Parts Call:877-728-8224

Visit us on the web:www.brinly.com

10

NOTES:

2.

!

!

!!

This symbol will help to point out important safety precautions throughout this manual. It means - ATTENTION!BECOME ALERT! Your safety is involved.

!

CONGRATULATIONS on your new Brinly-Hardy Dethatcher! Your dethatcher has been designed, engineered and manufactured to give you the best possible dependability and performance.

Should you experience any problem you can not easily remedy, please do not hesitate to contact our knowledgeable customer service department toll-free at 1-877-728-8224. We have competent, well trained technicians to help you with the assembly and use of your dethatcher.

CUSTOMER RESPONSIBILITIES

Read and observe the “RULES FOR SAFE OPERATION”. These instructions will enable you to assemble and maintain your dethatcher properly.

Follow a regular schedule in maintaining, caring-for and using your Brinly-Hardy Dethatcher.

RULES FOR SAFE OPERATION.....................................2 PARTS REFERENCE ......................................................3PARTS LIST .....................................................................3ASSEMBLY ......................................................................4-8OPERATION ....................................................................9MAINTENANCE ...............................................................9

RULES FOR SAFE OPERATION

• Know your towing vehicle controls and how to stop safely, READ YOUR OWNER'S MANUAL before operating.

• Do not allow children to operate the vehicle, do not allow adults to operate the vehicle without proper instruction or without having read the owner's manual.

• Do not carry passengers. Keep children and pets at a safe distance away.

• Always wear substantial footwear. Do not wear loose fitting clothing that can get caught in moving parts.

• Keep your eyes and mind on your vehicle/attachment and area being covered. Do not let other interests distract you.

• Stay alert for holes in the terrain and other hidden hazards.

• Do not drive close to creeks, ditches and public highways.

• Watch out for traffic when crossing or near roadways.

• When using any attachment, don't allow anyone near while in operation.

• Keep the vehicle and attachment in good operating condition and keep safety devices in place.

• Keep all nuts, bolts and screws tight to be sure the equipment is in safe working condition.

• The vehicle and attachment should be stopped and inspected for damage after striking a foreign object. The damage should be repaired before restarting and operating the equipment.

OPERATING HINTS

• Never operate dethatcher without safety wires installed.

• Always disconnect dethatcher from towing vehicle when cleaning or servicing the unit.

• Do not stand or ride on dethatcher, bodily harm could result.

• Only tow your dethatcher behind vehicles for which it is designed, riders and lawn/garden tractors

• Only tow your dethatcher behind vehicles for which it was designed - riders, lawn/garden tractors. DO NOT TOW this dethatcher behind high speed equipment such as ATV's, RTV's, or Pick up trucks.

• To avoid personal injury and/or equipment damage, never exceed the speed range of 3 to 5 M. P. H.

• When backing, carefully back straight to avoid jack-knifing which could result in damage to the equipment.

This symbol will help to point out important safety precautions throughout this manual. It means - ATTENTION! BECOME ALERT! your safety is involved

L-1797-A

L-1797-A

O W N E R ' S M A N U A L

For the latest product updates and setup tips:

Visit us on the web!www.brinly.com

MODEL:

DT-401BH

Important: This manual contains information for the safety of persons and property. Read it carefully before assembly and

operation of the equipment!

● Assembly● Installation● Operation● Repair Parts

D E T H A T C H E R

The limited warranty set forth below is given by Brinly-Hardy Company with respect to new merchandise purchased and used in the United States, its possessions and territories.

Brinly-Hardy Company warrants the products listed below against defects in material and workmanship, and will at its option, repair or replace, free of charge, any part found to be defective in materials or workmanship. This limited warranty shall only apply if this product has been assembled, operated, and maintained in accordance with the Operator’s manual furnished with the product, and has not been subject to misuse, abuse, commercial use, neglect, accident, improper maintenance, alteration, vandalism, theft, fire, water, or damage because of other peril or natural disaster.

Normal Wear Parts or components thereof are subject to separate terms as follows: All normal wear parts or component failures will be covered on the product for a period of 90 days.

Parts found to be defective within the warranty period will be replaced at our expense. Our obligation under this warranty is expressly limited to the replacement or repair, at our option, of parts found to be defective in material and workmanship.

HOW TO OBTAIN SERVICE: Warranty parts replacements are available, ONLY WITH PROOF OF PURCHASE, through our Pull Behind Accessories Customer Service Department. Call 877-728-8224.

This limited warranty does not provide coverage in the following cases:

a) Routine maintenance items such as lubricants and filters.b) Normal deterioration of the exterior finish due to use or exposure.c) Transportation and/or labor charges.d) The warranty does not include commercial and/or

rental use.

No implied warranty, including any implied warranty of merchantability of fitness for a particular purpose, applies after the applicable period of express written warranty above as to the part as identified below. No other express warranty whether written or oral, except as mentioned above, given by any person or entity, including a dealer or retailer, with respect to any product, shall bind Brinly-Hardy Co. During the period of the warranty, the exclusive remedy is repair or replacement of the product as set forth above.

MANUFACTURER’S LIMITED WARRANTY FOR

Pull Behind Accessories

The provisions as set forth in this warranty provide the sole and exclusive remedy arising from the sale. Brinly-Hardy Co. shall not be liable for incidental or consequential loss or damage including, without limitation, expenses incurred for substitute or replacement lawn care services or for rental expenses to temporarily replace a warranted product.

Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above exclusions or limitations may not apply to you.

During the warranty period, the exclusive remedy is replacement of the part. In no event shall recovery of any kind be greater that the amount of the purchase price of the product sold. Alteration of safety features of the product shall void this warranty. You assume the risk and liability for loss, damage, or injury to you and your property and/or to others and their property arising out of the misuse or inability to use this product.

This limited warranty shall not extend to anyone other than the original purchaser or to the person for whom it was purchased as a gift.

HOW STATE LAW RELATES TO THIS WARRANTY: This limited warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

IMPORTANT: The Warranty period stated below begins with the PROOF OF PURCHASE. Without the proof of purchase, the Warranty period begins from the date of manufacture determined by the serial number manufacturing date.

DETHATCHER WARRANTY PERIOD:The warranty period for this dethatcher is as follows: Steel frame parts – 2 Years. Tires, wheels and tines are normal wear parts - 90 days.

Brinly-Hardy Company, 3230 Industrial Parkway, Jeffersonville, IN 47130