Desktop Automatic Processor

INSTRUCTION MANUAL

Ecomat 9000

X-RAY FILM PROCESSOR

Ecomat 9000

TABLE OF CONTENTS

1

‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 2‥‥ 2

‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 4

‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 5‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 6

‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 7‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥ 8

‥‥‥‥‥‥‥‥‥‥‥‥‥ 10

‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥13

‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥14‥‥‥‥‥‥‥‥‥‥‥‥‥15

‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥18‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥19‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥20

‥‥‥‥‥‥‥‥‥‥‥‥‥20

1. Introduction 2. Safety Issues (please keep follow all the instructions) 3.Safety Precautions　3-1 Power and Earth Cables　3-2 Environment　3-3 Films and Chemical Solutions4. Parts Name5. Optional Parts6. Outer Measurement (mm)7. Installation　7-1 Preparation for Installation　7-2 Installation　7-3 Handling the Waste Chemical Solution and Drain Hose　7-4 Connecting the Water Hose　7-5 Power Supply8. Preparation for Operation　8-1 Cleaning the Developing and Fixing Racks　8-2 Mixing the Developing Solution 　8-3 Mixing the Fixing Solution　8-4 Pouring the Chemical Solution　8-5 Setting the Racks9. Operating Instructions　9-1 Power Switch and Water Supply　9-2 Developing the Films　9-3 Turning off the Power10. Operating Explanation11. Maintenance and Cleaning　11-1 Daily Inspection　11-2 Monthly Maintenance　11-3 Changing the Chemical Solution　11-4 Periodical Inspection　11-5 List of Consumables　11-6 Inspection Check Sheet12. Damage and Inspection13. Basic Spec14. Option Parts　14-1 Stand　14-2 Water Solenoid Valve　14-3 Water Filter Kit　14-4 Water Pump Unit 15. Warranty and After Service

2

Thank you very much for your purchase of desktop compact automatic film processor, ECOMAT9000. This manual includes the basic instructions of daily use, maintenance, and countermeasures during the troubles of ECOMAT9000.

It is important that all the instruction, description and safety issues are reviewed thoroughly before using the equipment. After you finish studying the manual, please keep this manual with the warranty card.

1. Introduction

2. Safety Issues (please keep follow all the instructions)

Please read the "safety issues" thoroughly before using the equipment. The following "safety issue" includes information on proper use to avoid damage to the equipment and human (users). There are many different diagrams and signs showing different meanings and all of them have important meanings. Please follow them carefully.

Warning

Warning

Sample of signs and diagrams:

Warning

Use only 200V. It may cause fire and electric shock.

Make sure the earth cable is inserted. It may cause electric shock if it is not inserted properly.

Please turn off the power during maintenance. It may cause electric shock.

This shows that the action is required. There are actual photos showing the safety issues (the left photo shows a plug being pulled from an outlet)

This shows that the action is prohibited. There are actual photos showing samples of safety issues.

This shows that you will need to pay attention to the warnings. There are actual photos showing samples of safety issues.

Warning Please do not ignore this sign. It may cause serious injuries or death to the user. Warning Please do ignore this sign. It may cause injuries and damage to the equipment.

Do not open the top cover while the equipment is running. The equipment includes motors which may cause injuries if you touch it. The chemical solution may get into your eyes or clothe.

For any trouble or damage, stop the operation, pull out the power cable and contact your local sales agent or distributor. If operation continues during any trouble, it may cause fire or electric shock.

3

Warning

Warning

For installation, find a flat location where there is no vibration. If it is not properly installed, the different chemical solution may get mixed up and cause trouble.

Place the power cable so that it may not be accidently pulled out. It may cause injuries or damage.

Do not place any objects on top of the power cable. It may cause fire.

Do not place any objects on top of the unit. It may cause damage, fire or injuries.

When the power cable is pulled, do not pull the cord. Hold the power plug to pull it out. It may cause trouble or electric shock.

This equipment weights about 30kg. Make sure to be careful when opening the package and handling the unit. It may cause injury and damage to the unit.

Do not turn the unit side ways during transportation. It will cause damage.

If the unit is used after the power has been turned off for a long time, make sure the unit is operating properly. It may cause damage or fire.

In case the equipment is not used for a long time, turn off the power and pull out the power cable. It may cause damage or fire.

The unit is not explosion and fire proof. Do not use the unit where there are flammable products.

Do not use mobile phone or any other device which generates electromagnetic field. It may cause damage to the unit.

During transportation, turn off the power, pull out the power cable and take out all the chemical solution. Make sure the unit does not turn over. It may cause damage and injuries.

Make sure to thoroughly wash off the chemical solution in case you come in contact. After handling the chemical solution, please wash hands. If the chemical solution gets inside the eyes, wash thoroughly with water and consult with a doctor.

Please use only a 200V, 10A cable. Avoid multiple plug connection. It may cause fire, trouble or injuries.

Please do not modify the unit. It may cause fire, electric shock and injuries.

During operation, please make sure the equipment is stable and do not shake the unit. It may cause damage, electric shock or fire.

Do not splash any liquid to the equipment. Do not install the equipment where water is present. It may cause damage and electric shock.

Only a authorized engineer should open and fix the unit. It may cause fire, electric shock or injuries unless you are trained. Please contact your local agent or distributor.

Make sure there is enough ventilation. If there is not enough ventilation, it may cause trouble.

4

30

10

80

30

℃

5

℃

%RH

3. Safety Precautions

3-1 Power and Earth Cables

3-2 Envirnment

3-3 Proper Films and Chemical Solution

Power ; 220/240V,4.5A ( or 110/120V ,9A )

Make sure to connect to the Type 3 ground cable.

Requested conditions: 　　　　　　　　　　　　　　　　　　　　　　　　　　　　 Temp:10～30℃　　　　　　　　　　　　　　　　　　　　　　　　　　　　　　 Humidity:30～80％ RH　　　　　　　　　　　　　　　　　　　　　　　　　　　　　 Water Temp: 5℃ Above

The dark room will require a ventilation fan and exhaust pipe. Dark Room lamp should be diode type S2 (ortho regular)

WarningDo not place any unnecessary objects inside the dark room.●

Film ・・・ Ortho regular No specific brand of films (please contact your local dealer for more information)Chemical Solution ・・・ Dev solution Fix solution Mixing method ・・・ 8-2 Mixing method 8-3 Fix Solution mixing method

＊Warning on chemical solution 　The Developing Solution has a high percentage of alkali, and fixing solution contains acidic liquid. Make sure they do not come in contact with human skin and eyes. The used chemical solution (waste) needs to be disposed accordingly the regulation of your country. Please contact your waste disposal agent for handling the chemical solution waste.

5

4. Parts Name

4-1 Name of Parts （A）

4-2 Name of Parts （B）

②

③

⑦⑥

⑤

①

④

①

⑫

⑭⑬

⑪

②

④ ⑥

⑦

③⑤

⑧

① Block plate　

② DEV rack

③ Cross over guide（DEV）

④ FIX rack

⑤ Cross over guide（FIX）

⑥ Water Rack

⑦ DRY Rack

⑧ Drain Valve（DEV）

⑨ Drain Valve（FIX）

⑩ Drain Valbe　

⑪ Replenishing Hose Blue（FIX）

⑫ Replenishing Hose Red（DEV）

⑬ Water supply cup

⑭ Drain Valve

① Insertion case

② Insertion case lid　

③ Top cover　

④ Drying cover　

⑤ Rubber stand　

⑥ Power switch（POWER）

⑦ Ready lamp（READY）

⑧ Front cover

⑧

⑨⑩

Ecomat 9000

X-RAY FILM PROCESSOR

Ecomat 9000

X-RAY FILM PROCESSOR

6

5. Optional Parts

Measuring Cup × 1

Spare parts：

Replenishing tank (10L) × 2For DEV Solution and FIX solution

5

8

3 4

2

109

1

6 7

1 4

2

3

4

5

6

7

8

2

2

2

1

9

10

1

1

4

2

4

No. Part No. Part Name Qty

117-3730005

117-3730006

117-3270045

117-3270046

117-3270047

117-3850002

117-3850001

117-3220011

117-3610051

117-3610052

O-ring ,P12

O-ring,P18

Gear,rightA

Gear,leftA

Gear,leftB

Spring,roller

Spring,roller

Support,shaft

Fook,right

Fook,left

7

Front view

Plane view

Side view

6. Outer Measurement (mm)

565

723

463

550

1013

655

570

614

109

723

8

Exhaust exit

Dark room

Ventilation fan

7. Installation

7-1 Preparation for Installation

7-2 Installation

7-3 Handling the Waste Chemical Solution and Drain Hose

This equipment is designed to be installed in a complete dark room. Check the measurement of the equipment and keep enough room and space in the dark room, and also keep enough space to work for changing the films. Make sure there is a power outlet for 100V - 200V, 10A. Make sure there is water supply, and drainage. In case you purchase an optional water solenoid valve, water filter unit, water pump unit, make sure there is enough space, installation space and additional power outlet. (For more details on the optional parts, please refer to page 23).

Please conduct the installation inside the dark room only. Please adjust the height position of the equipment by turning the rubber of the stand to make sure it is parallel to the ground. 　　　　　　　　

Connect each of the waste and water hose. Insert the Waste Hose to the waste drain. Collect the chemical solution waste by connecting the waste hose to the tank. Please cut the hose to the necessary length. Ask the waste disposal agent to collect the chemical solution waste.

WarningIf the main unit is tilted, the developing solution and fixing solution may get mixed up inside the unit and over flow. Please make sure the unit is installed flat to the ground.Please refer to the following recommended environment for installation　TEMP： 10～30℃　HUMIDITY： 30～80％RH　WATER TEMP：5℃ or aboveMake sure there is ventilation fan and exhaust exit inside the dark room.

○

○

○

9

Tap water

Water coupling

Hose joint

7-4 Connecting the Water Hose

7-5 Power Supply

① Loosen the hose joint and insert the water coupling to the tap water. ② Use the 3 screws and hold the water coupling to the tap water③ Check the length of the water hose and cut to the right length. ④ After completing the connection, cut to the hose to the necessary length and dispose the remains. ⑤ After the hose is connected, run the water to check if there is no leak.

WarningDo not tighten the hose joint to tightly. The bucking may break and cause water leakage.●

WarningMake sure the hoses do not bend in a U shape. Please check the flow of the waste is smooth. If there is any clog inside the hose, it may cause damage to the main unit.

●

WarningThe water coupling comes with a continuous flow valve. (less than 2 liter / min) In case a different type of water hose is used, please use this water coupling.

●

WarningMake sure to hold onto the plug part when pulling out the power plug. Do not pull the cord. ●

① Make sure to use 220V/240V,5A ( or 110/120V , 10A) ② Make sure to connect to the Type 3 ground cable.

10

8. Preparation for Operation

8-1 Cleaning the Developing and Fixing Racks

8-2 Mixing the Developing Solution

8-3 Mixing the Fixing Solution

① Clean each of the racks with water and wipe off the dirt. ② Soak each of the rack and cross over guide into a bucket of warm water. Wipe off any dirt on the rollers and guides with a piece of cloth.

① Use the attached Measuring Cup and pour 4 liter of water ② Take out the Solution A and add to the 10 liter tank. ③ Take out the Solution B (brown bin) and add to the 10 liter tank. ④ The total volume should be 10 liters. Make sure to mix the solution thoroughly.

WarningWhen handling the chemical solution, make sure to use rubber gloves to avoid contact with the solution. Clean your hands thoroughly afterwards.

●

WarningThe chemical waste needs to be collected using a waste tank and dispose it accordingly to your the country's regulation.

●

Both Solution A and Solution B is highly concentrated solution, and may cause crystallization when the room temperature is cold. In case the solution is crystallized, mix the solution with warm water and pour into the 4 liter pot. 　

●

① Use the attached Measuring Cup and pour 4 liters of water.② Use the A bottle and add to the 10 liter tank. ③ Use the B bottle and add o the 10 liter tank.. ④ Add more water to make the total volume of 10 liters and mix the solution thoroughly.

10 liter tank

Solution ASolution B

Measuring Cup

11

8-4 Pouring the Chemical Solution

WarningWhen handling the chemical solution, make sure to use rubber gloves to avoid contact with the solution. Clean your hands thoroughly afterwards.

●

WarningThe chemical waste needs to be collected using a waste tank and dispose it accordingly to your the country's regulation.

●

If you mix the A solution with B solution, it will dissolve and become cloudy. Make sure to water down the solution A and then mix the solution while adding the Solution B.

●

Carefully pour each of the Developing and Fixing Solution into the racks in order using the 4L pot. Check the solution level line and pour until the solution reaches the line. Both the developing rack and fixing rack has a 2 liter capacity.

Valve Insertion line

solution level

10 liter tank

Solution ASolution B

Measuring Cup

12

Water rack

Drying rack

Hook

Stay

Hook

Drying rack

8-5 Setting the Developing Rack

1) Set each racks, developing rack, fixing rack, water rack carefully in each location. 2) Slide each of the racks towards the left side until there is a stopper. The gear will hold the rack. 3) Place the Drying rack on top of the Water Rack, and the air case to the dryer exit.

Place the cross over guide to the ratchet in between each of the racks. Check the arrow mark and place it to the same direction of the film. Listen carefully to the sound of the gear when it connects. Make sure the cross over guide does not move.

Washer Rack

Drying rack

Air case

WarningIn case the fixing solution gets inside the developing rack, the final image will be effected. Make sure to clean the developing rack to get clear image.

●

Both the developing and fixing solution contains a high percentage of alkali and acidic solution. Make sure they do not get mixed up inside the unit.

●

Ecomat 9000

X-RAY FILM PROCESSOR

13

9. Operating Instructions

9-1 Power Switch and Water Supply

9-2 Developing the Films

9-3 Turning off the Power

WarningMake sure the power plug and the earth plug are connected to avoid any power leakage. Check inside to make sure the solution is filled. The unit may break if the power is turned on without any solution.

Turn on the power ON（○ →｜）

●

WarningMake sure to use the appropriate film and dark room lamp during operation. ●

WarningIf you keep the lid, film insertion case and top cover, closed it will cause damage to the top cuver、unit ,or poor image due to excessive moisture and gas.

●

1) Make sure the READY lamp is lit. 2) Use 1 to 2 films for cleaning purpose everyday before start using the equipment. 3) Turn off the light inside the dark room and turn on the dark room lamp. 4) Open the lid of the film insertion, and insert the film accordingly to the left side of the film guide. In case the width of the film is less than 8 inches, place the film in the middle of the case.

5) After inserting the films, the READY sign will start to flash and buzzer will go off. After closing the lid, you may turn on the light inside the dark room. 6) The READY sign will disappear when the films are inserted. 7) When the READY sign starts to flash, the next film is ready to be inserted. 8) When inserting films continuously, please follow the above instructions, 3 to 7. 9) When the operation is completed, make sure to close the water supply.

1) Turn off the main Power (OFF ○). 2) Close the water supply.3) Pull out the power plug 4) Check the below diagram and open the insertion case, lid and the top cover for better ventilation.

Insert Case

14

10. Operating Explanation

After Turning on the Power

When the power is turned on, the Developing / Drying Heater, Drying Blower, Drive Motor starts to run and each and all rollers will turn.

●

For Completing the Operation,

When completing the film processing, turn off the power, take out the insertion case. Turn off the supply.

Please refer to page 14, Operation for more details.

●

Temperature Control

The heaters inside the developing rack and fixing tank will control the temperature of the developing solution. Once it reaches the temperature, the ready sign will light and the buzzer will go off three times. In order to maintain the temperature of the developing solution, the heater will turn on to control the temperature. The temperature of the Dryer will also stop once it reaches the set temperature. Once the temperature drops, the temperature control will start again.

●

The Film Developing and READY Status

When the film is being processed, open the insertion case, insert the films according to the film guide to the right. The film sensor located at the middle of the film entrance will catch (sense) the film which triggers the READY sign, turn on the drive motor, rollers and the drying blower. Then it will automatically transport the films. When the film sensor catches the film, this will trigger the developing and fixing replenishing pumps to run and they will stop when the replenishing is completed. Once the film is completely inside the unit, the READY sign will flash and the buzzer will go off 3 times. This means that the next film can be inserted. When the last film is inserted and the READY sign starts to light, it will take 7 minutes for the drive motor and drying blower to go into wait mode.

●

Film Insert Case

15

11. Maintenance and Cleaning

11-1 Daily Inspection

11-2 Monthly Maintenance:

11-3 Changing the Chemical Solution

In order to keep the equipment in good condition, make sure to conduct a periodical maintenance and cleaning. 1) Make sure to clean and check the film insertion part. 　a) Make sure the insertion board is clean. If there is any dirt or dust, make sure to wipe off the dirt off by using a wet towel or cloth.

WarningIf the developing solution splashes onto the insertion case, the image will be affected. ●

WarningIf you use the disposal tank when it is full of disposal waste, the waste will leak to the floor. ●

　B) If the insertion case is taken out, handle them carefully as the case and the lid will come apart in 2 pieces. 　C) After cleaning, make sure the insertion case is connected correctly.

2) Checking the disposal waste　Make sure to check the remaining of the disposal waste.

3) Checking the replenishing solution 　Make sure to check the remaining amount of the replenishing solution. 4) Checking the water coupling 　Make sure to check there is no water leakage from the water coupling.

Clean each racks and cross over.Soak each racks and each cross over racks into warm water and use a clean towel to wipe off any dirt (oxidation, dust, chemical composition)

Condition for operation (using the cleaning films and daily use of 3 films / week): Change the chemical solution every 2-3 months in order to keep the quality of the processing ability. The periodic changing of chemical solution will vary depending on the amount of processed films.

16

11-4 Recommended Inspection

This equipment uses chemical and water. In order to keep the quality of the unit in good condition, please conduct a safety inspection on a yearly basis. For further details on the safety inspections, please contact your local sales agent / distributor.

11-5 List of Consumables

Name of parts Roller springs O ring 12 O ring 18 Replenishing elbow Gear Right A Gear Left A Refresh fan

Part No. 117-3850002 117-3730005117-3730006117-3710007117-3270045117-3270047117-1190026

when to changeafter 1.5 years after 2 yearsafter 2 years after 2 yearsafter 2.5 yearsafter 2.5 years after 2.5 years

Warning1) When dismantling the racks, make sure the chemical solution does not leak to the adjacent racks. 2) Use a brush to clean off the crystallized dirt on the gears. 3) Do not use a hard brush when cleaning the rollers. It will damage the surface of the rollers.

Please change the following spare parts (the list may vary depending on conditions and daily maintenance)

dry and then install

Cleaning Period Method Warning

Developing cross over guideFixing cross over guide

Dev / Fix Water Rack

Dev Rack

Fix rack

Water rack

2~3months

2~3months

2~3months

2~3months

2~3months

soak in warm water and wipe

soak in warm water and wipe

1) Clean the rollers using cleansing solution 2) Wash off using water

1) Clean the rollers using cleansing solution 2) Wash off using water

1) Soak into a general bleach agent for 15 minutes2) Roll the rollers inside the bleach for 2-3 minutes3) Wash off using water

Cleaning Period Method Warning

Dev Tank Fix Tank

Water Tank Insertion Guide plate Film sensor Other exterior parts

2~3 months

2~3 months

2~3 months

Everyday

Every month

Everyday

Use warm water Use warm water

Use warm water

Use a wet cloth Use a wet cloth Use a wet cloth

Inspection and Cleaning

Make sure the plate is dry

17

11-6 Inspection and Check Sheet

DescriptionNo Content Check column

All the above inspections and checking will help keep the unit working and for better results.

2

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

18

19

1Check if there is no crystallization of solution Check if the solution is clean

Check if there is no crystallization of solution Check if the solution is cloudy

Check if there is no crystallization of water Check if the water does not contain any dirt

Is there any dirt on the DEV rack? Are the gears and springs attached correctly?

Is there any dirt on the FIX rack? Are the gears and springs attached correctly?

Is there any dirt on the Water rack? Are the gears and springs attached correctly?

Is there any dirt or crystallization of the solution? Are the gears and springs attached correctly?

Check is there is any dirt or crystallization

Turn on the Power and check if the READY lamp will turn on after temperature reaches the set temperature

Check for the buzzer sound when the Power is turned o and when the film is being processed.

When the READY turns on, check the temperature of DEV tank. The temperature should be 35℃.

Transportation test: check if the film is transported

Drying Test: check if the processed film is dried

Replenishing Test: check if the DEV / FIX tank is less

Check for any abnormal sound

Check if the water is running from the water tap

Make sure there is not any unnecessary items inside the dark room. Make sure there is no light leakage. Make sure the dark room lamp is working.

Is the developing solution clean? Is the solution crystallized?

Is the fixing solution clean? Is the solution cloudy?

Is the water supply dirty? Is the water clean?

Check the DEV rack

Check the FIX rack

Check the Water rack

Check the Dry rack

Check the cross over rack (both)

Does the RRADY lamp turn on?

Check the buzzer sound

Is the DEV temperature set? Use 1-2 films for testing

Check for water supply

Check if the ground cable is connected

Check if there is any water leakage around the unit

Check the dark room

18

12. Damage and Inspection

In case of any trouble of operation, please conduct an inspection. If the trouble is not fixed or do not understand the inspection, please contact your local agent / distributor.

Operation stopped (green)

The operation does notstop when READY

There is abnormal sound

The films are not transported

The films comes out wet

Image is light

Double image

Irregular image

Scratches on images

Image is too dark

Films do not come out smoothly

READY lamp does not turn

Damage Inspection point Counter measurePlug the power cord

Press the Reset button

If the lamp is lit, electricity is running.

Push the insertion case tightly.

Make sure there is no light to the insertion.

Set all the racks properly

Set the cross over guide properly.

Clean the racks

Use the proper amountCheck the amount in tank.

Change with new solution.

Reset the safety thermo.

Change the DEV solution

Check the temperature of the Developer

Keep enough solution in Tank is enough.

Change to new DEV Solution

Do not expose to the dark Change the light filter

Insert all the way to the end

Close the lid completely

Pour the correct amount

Place the unit evenly to the ground.

Run the water during processing

Clean off the oxidation

Use them properly.

Change to new solution

Change to new solution Pour the correct amount

Rest the safety thermo

Check the power cord properly

Is the breaker working?

Look for red lamp.

Check if the insertion case is inserted

Check for any light leakage touching the film sensor.

Check the DEV / FIX / DRY rack are set properly.

Check if the cross over guides are set

Check if the unit inside the racks turns smoothly by hand.Check if there is any oxidation.

Check if the amount of FixingSolution is enough or too little.

Check if the solution is dirty and old.

Drying temperature is not set.

Check if the DEV and FIX solution is not mixed.

Check the temperature of DEV solution

Check if the amount of DEC solution

Check if the DEV solution is not old.

The film is exposed to the dark lamp Check if the dark room lamp filter is Correct.

Check if the insertion case is inserted

Check if the insertion case lid is closed

Check if the level of the solution is correct

Is the level of solution even?

Is the water running.

Check for oxidation on insertion case and roller of each racks.

Are the films and cassettes used and handled properly.

Check if the temperature of DEV is too high. Was the solution mixed properly?

Check if the FIX solution is mixed properly. Is the amount enough?

The temperature of solution is not

* flashing: temp solution is rising. Enough* On: temp is set

19

Transportation: Processing speed Processing films Processing capacity Processing solution

Tank Capacity:

Processing temperature Temperature control

Solution replenishment

DEV solution mixing

Water supply

Safe mode(DEV/FIX/DRY) Stand by mode

Installation environment Power Dimension

Weight Option

diagonal roller transportation system 90 - 120 seconds

sheet films 14" x 17" - 5" x 7"

100 films / hour

regular chemical solution (developing and fixing)

DEV: 3.7L / FIX: 2.4L / WATER: 2.3L

Developing: 35℃ Drying: 60℃ ± 5℃

Developing: control by heat thermostat Fixing control by heat thermostat Drying control by thermister

Automatic film replenishment by film sensor Rotation by mixing plate

Running water Over heating protection, manual safety thermo (DEV/FIX/DRY)Breaker cord

power conserve, roller anti-degradation, temperature control, Roller drive motor operation

Temp: 20C +/- 10C, Humidity: 55% +/- 25%Water Temp: 5C higher than the tap water

220/240V,4.5A ( or 110/120V ,9A ) 565 x 722 x 464cm 27.5kg

StandWater pumpSolenoid valveWater filter kit

13. Basic Spec:

Spec is subject to change without prior notice for better performance.

20

14.Option Parts

Following is the details of optional items for ECOMAT9000.

14-1 Stand

14-2 Water Solenoid Valve

14-3 Water Filter Kit

14-4 Water Pump Unit

Build your own stand to be used for ECOMAT9000 to be used in the dark room

Solenoid Valve will automatically supply the water. During the film processing, this will supply the water and when the film processing is complete, the water supply will automatically stop. The installation will require a replacement of water pipe and the ECOMAT9000. The installation instruction is included in the solenoid valve unit. Please refer to the instructions of the solenoid valve.

Water filter can be installed when the quality of the water is not good. It is recommended to install the water filter along with the solenoid valve. It is necessary to replace the water pipe. Please refer to the instruction inside the water filter unit.

If there is no water supply, this is used to supply the water. Pour 20 liters of water into a tank and use the water to replenish the water of the water tank. Please change the water of the tank after 20-30 processed films. For installation, please refer to the instructions inside the water pump unit.

15. Warranty and After Service

In order to keep the unit is good condition, please review this manual in order to keep the performance of the equipment in good condition.

After service In case of any trouble, please refer to page 22 of Damage and Inspection. Contact your local agent / distributor for further instructions and report the following:　1) details of damage (trouble) 　2) model name (ECOMAT 9000)　3) Date of installation 　4) Serial number of the equipment ECOMAT9000 is thoroughly inspected before shipment. Please make sure to keep the warranty card with the equipment. After normal use of the equipment, the warranty period is 1 year after installation. The warranty is not valid if the equipment is not used properly. Any replacement or service charges after the warranty period will be charged. Please contact your local agent / distributor for more details. The supply of the recommended spare parts will be discontinued 7 years after the announcement of discontinuation. However, even after 7 years of the announcement, the troubles may be fixed. It is best to contact your local agent / distributor in such case.

1.

2.

3. 4. 5.

6.