Design of Class-D Audio Amplifiers
description
Transcript of Design of Class-D Audio Amplifiers
![Page 2: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/2.jpg)
Chun-Hsien Su 2
OUTLINE
1. Introduction of Class-D Audio Amplifier
2. Large-Power Class-D Applications
4. Sigma-Delta Class-D Audio Amplifiers
5. Conclusions
3. Integrated Class-D Audio Power Stages
![Page 3: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/3.jpg)
Chun-Hsien Su 3
Introduction of Class-D Audio Amplifier
η = 30% at temp rise test condition.
– Traditional Class-AB Amplifier
Class AB amplifier uses linear regulating transistors to modulate output voltage.
![Page 4: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/4.jpg)
Chun-Hsien Su 4
Introduction of Class-D Audio Amplifier– Class-D Audio Amplifier
Class D amplifier uses MOSFETs that are either ON or OFF.
PWM technique is used to express analog audio signals with ON or OFF states in output devices.
![Page 5: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/5.jpg)
Chun-Hsien Su 5
Basic PWM Operation
![Page 6: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/6.jpg)
Chun-Hsien Su 6
Audio Output Spectral Density
LC-filtered
Carrier and modulated signalsFundamental
![Page 7: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/7.jpg)
Chun-Hsien Su 7
Topology Comparison: Class AB vs. Class D
![Page 8: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/8.jpg)
Chun-Hsien Su 8
Efficiency: Class AB vs. Class D[From TI’s report]
![Page 9: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/9.jpg)
Chun-Hsien Su 9
Measured Efficiency [From TI’s data]
– TI-TPA2000D4
![Page 10: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/10.jpg)
Chun-Hsien Su 10
Temperature vs. Output Power– Class-D Advantage: Less Heat
![Page 11: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/11.jpg)
Chun-Hsien Su 11
Battery Life
A head to head test ofTI’s class-AB and class-D~1W mono solutions:Class-AB - TPA731Class-D - TPA2001D
Both set-up on the PnPplatform powered by3x1.2V NiMH batteriesdriving a typical 8-Ωspeaker used in wirelessapplications.
![Page 12: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/12.jpg)
Chun-Hsien Su 12
Battery Life
A head to head test ofTI’s class-AB and class-D~1W mono solutions:Class-AB - TPA731Class-D - TPA2001D
Both set-up on the PnPplatform powered by3x1.2V NiMH batteriesdriving a typical 8-Ωspeaker used in wirelessapplications.
![Page 13: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/13.jpg)
Chun-Hsien Su 13
Analogy to Buck DC-DC Converter
![Page 14: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/14.jpg)
Chun-Hsien Su 14
Loss in Power Device
![Page 15: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/15.jpg)
Chun-Hsien Su 15
Full Bridge versus Half Bridge
– Full Bridge
– Full Bridge
![Page 16: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/16.jpg)
Chun-Hsien Su 16
Full Bridge versus Half Bridge (Cont.)
![Page 17: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/17.jpg)
Chun-Hsien Su 17
Major Cause of Imperfection
Gate Driver
PWM
Feedback
Audio source
Dead timeDelay time
ArchitectureAnalog/digitalw/SDM
Modulation errorQuantization error
Single-bridge/Full bridgeFilterless modulation scheme
Switch nonidealities
Finite RonBody diode Recovery(EMI)
Nonlinear LC
Poor PSRRNoise coupling
![Page 18: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/18.jpg)
Chun-Hsien Su 18
THD and Dead Time
![Page 19: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/19.jpg)
Chun-Hsien Su 19
Shoot Through and Dead Time
- Shoot through charge increases rapidly as dead time gets shorter.
- Need to consider manufacturing tolerances and temperature characteristics.
![Page 20: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/20.jpg)
Chun-Hsien Su 20
Power Supply Pumping
- Significant at low frequency output- Significant at low load impedance- Significant at small bus capacitors- Largest at duty = 25%, and 75%
![Page 21: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/21.jpg)
Chun-Hsien Su 21
EMI consideration: Qrr in Body Diode
1. Low side drains inductor current2. During dead time body diode of low side conducts and keep inductor current flow3. At the moment high side is turned ON after dead time, the body diode is still conducting to wipe away minority carrier charge stored in the duration of forward conduction. This current generates large high frequency current waveform and causes EMI noises.
![Page 22: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/22.jpg)
Chun-Hsien Su 22
Gate Driver: Why is it Needed? Gate of MOSFET is a capacitor to be charged and discharged. Typical effective capacitance is 2nF.
High side needs to have a gate voltage referenced to it’s Source.
Gate voltage must be 10-15V higher than the drain voltage.
Need to control HS and LS independently to have dead time.
![Page 23: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/23.jpg)
Chun-Hsien Su 23
Functional Block Diagram Inside Gate Driver
With the addition of few components, they provide very fast switching speeds and low power dissipation.
High side needs to have a gate voltage referenced to it’s Source.
Need to control HS and LS independently to have dead time.
![Page 24: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/24.jpg)
Chun-Hsien Su 24
Bootstrap High Side Power Supply
When Vs is pulled down to ground through the low side FET, the bootstrap capacitor (CBOOT) charges through the bootstrap diode (Dbs) from the Vcc supply, thus providing a supply to Vbs.
![Page 25: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/25.jpg)
Chun-Hsien Su 25
Power Dissipation in Gate DriverWhenever a capacitor is charged or discharged through a resistor, half of energy that goes into the capacitance is dissipated in the resistor. Thus, the losses in the gate drive resistance, internal and external to the MGD, for one completecycle is the following:
GSWG QfVP
![Page 26: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/26.jpg)
Chun-Hsien Su 26
Power Dissipation in Gate Driver (Cont’d)
The use of gate resistors reduces the amount of gate drive power that is dissipated inside the MGD by the ratio of the respective resistances.
These losses are not temperature dependent.
![Page 27: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/27.jpg)
Chun-Hsien Su 27
MOSFET Power Switch
A MOSFET is a voltage-controlled power switch.A voltage must be applied between Gate andSource terminals to produce a flow of current inthe Drain.
![Page 28: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/28.jpg)
Chun-Hsien Su 28
Key Parameters of Power MOSFETs
(1). Voltage Rating, BVDSS : Drain-source breakdown voltage. Temperature dependent.
(2). Gate Charge, Qg : Directly related to MOSFET speed Temperature dependent.
(3). D-to-S On-Resistance, RDS(ON) : Directly related to MOSFET conduction losses. Temperature dependent.
(4). Body Diode Reverse Recovery Characteristics, Qrr, trr , Irr , and S factor. Influence THD, EMI, and Efficiency. Temperature dependent.
(5). Package : Power dissipation capability, current capability, internal inductance, internal resistance, electrical isolation, and mounting process.
![Page 29: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/29.jpg)
Chun-Hsien Su 29
Voltage Rating, BVDSS
This is the drain-source breakdown voltage (with VGS = 0). BVDSS should be greater than or equal to the rated voltage of the device, at the specified leakage current, normally measured at Id=250uA.
This parameter is temperature-dependent and frequently ∆BVDSS/∆Tj (V/°C) is specified on datasheets.
BVDSS MOSFET voltages are available from tens to thousand volts.
![Page 30: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/30.jpg)
Chun-Hsien Su 30
Gate Charge, Qg
parameter is directly related to the MOSFET speed and is temperatureindependent. Lower Qg results in faster switching speeds and consequently lower switching losses.
The total gate charge has two main components: the gate source charge, Qgs and, the gate-drain charge, Qgd (often called the Miller charge).
![Page 31: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/31.jpg)
Chun-Hsien Su 31
D-to-S On-Resistance, RDS(ON)
This is the drain-source resistance, typically specified on data sheet at 25°C with VGS = 10V. RDS(ON) parameter is temperature-dependent, and is directly related to the MOSFET conduction losses. lower RDS(ON) results in lower conduction losses.
![Page 32: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/32.jpg)
Chun-Hsien Su 32
Body Diode Reverse Recovery Characteristics, Qrr, trr , Irr , and S Factor
Power recovery characteristics are temperature-dependent and lower trr, Irr and Qrr improves THD, EMI and Efficiency η.
Power MOSFETs inherently have an integral reverse body-drain diode. This body diode exhibits reverse recovery characteristics. Reverse Recovery Charge Qrr, Reverse Recovery Time trr, Reverse Recovery Current Irr and Softness factor (S = tb/ta), are typically specified on data sheets at 25°C and di/dt = 100A/us.
![Page 33: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/33.jpg)
Chun-Hsien Su 33
Package
MOSFETs devices are available in several packages as SO-8,TO-220, D-Pak, I-Pak, TO-262, DirectFET™, etc.
The selection of a MOSFET package for a specific application depends on the package characteristics such as dimensions, power dissipation capability, current capability, internal inductance, internal resistance, electrical isolation and mounting process.
![Page 34: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/34.jpg)
Chun-Hsien Su 34
Choosing the MOSFET Voltage Rating
– Topology (Full Bridge or Half Bridge)
MOSFET voltage rating for a Class D amplifier is determined by:
– Desired POUT and load impedance (i.e. 250W on 4Ω)
– Modulation Factor M (80-90%)
![Page 35: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/35.jpg)
Chun-Hsien Su 35
Trends in Class-D Audio Amplifiers
– Make it smaller! higher efficiency smaller package Half Bridge
– Make it sound better! THD improvement fully digitally processed modulator
![Page 36: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/36.jpg)
Chun-Hsien Su 36
– Patent Blooming since Y2KUS Patent Class 330/207A – Class-D Amplifier
1985
1986
1987
1988
1989
1990
1991
1992
1993
1994
1995
1996
1997
1998
1999
2000
2001
2002
2003
2004
2005
40
3033
25
1513
Patent #
50+
Trends in Class-D (1)
![Page 37: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/37.jpg)
Chun-Hsien Su 37
– Systems by ICs
Trends in Class-D (2)
Bipolar
CMOS
DMOS (double-diffused MOS)
• It is a (lateral) double-diffused MOS transistor.• The device is asymmetrical.• A lightly doped Nwell(extended drain) region supports high drain voltages.• The thin gate oxide allows a high device but restricts• The Pbody is shorted to source of device in metal 1.
DMOS features:
![Page 38: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/38.jpg)
Chun-Hsien Su 38
– Full versus Half, Performance versus Cost
Trends in Class-D (3)
Full Bridge
Half Bridge
![Page 39: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/39.jpg)
Chun-Hsien Su 39
– Performance Improved by Analog FB Loop
Trends in Class-D (4)
This structure improves output waveform & PSRR.
This patent can be avoided by using different architecture.
US Patent : 6300825, issued 2001/10/9“PWM with feedback loop Integrator”
Similar: Yokoyama 4504793 1985/3/12
![Page 40: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/40.jpg)
Chun-Hsien Su 40
– Filterless Modulation for Portable Applications
Trends in Class-D (5)
Information in pulse width Information in phase
Limits the development of small-power (~1W) class-D amplifier.
Can be solved by using different modulation schemes.
Gate Driver
US Patent : 6262632, issued 2001/7/17“Concept and method to enable filterless, efficient operation of Class-D amplifiers”
![Page 41: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/41.jpg)
Chun-Hsien Su 41
– Performance Improvement by Sigma-Delta?
Trends in Class-D (6)
PWM
Delta
Sigma-Delta
The power efficiency and the signal-to-noise ratio (SNR) for a amplifier based on the above scheme are compared with the values typical of linear and PWM amplifiers of the same rated power. The power efficiency of the solution is an intermediate value between the linear and PWM amplifiers, whereas SNR mainly depends on the modulator type adopted. A SNR around 60–70 dB was estimated by adopting a fourth-order modulator. However, this value can be significantly improved by increasing the switching frequency or the modulator order.[Dallago, Tran. CAS-I, Aug, 1997]
![Page 42: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/42.jpg)
Chun-Hsien Su 42
Trend in Class D Amplifiers
(1). Reduction of power circuit parasitic capacitance by technological improvement of both semiconductor and magnetic devices;
In any case, to extend the power range of high-frequency modulation, future studies should be oriented in the following direction:
(3). development of extended modulation techniques (for example of multilevel type or nonconstant switching period type or, generally, of hybrid type) allowing a lower switching frequency under the same baseband performance.
(2). Adoption of soft-switching schemes able to perform a larger exploitation of converter parasitic parameters under a load range that is as wide as possible;
![Page 43: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/43.jpg)
Chun-Hsien Su 43
1-bitPDM
PWMClass-D CT SDM
Comparator Run-free Clocked
Output PWM 1-b PDM
Min. pulse Width
1/fsfs<1MHz
1/fsfs>1MHz
Drive H-bridge
OK May burn out
For second-order Mfs=40kHzx128=5.12MHz
Gate Driver
High-orderSingle-bit
M
Audio source Bit flipping(bit grouping)
Open-loop, Full-bridge, low-OSR M with bit grouping
(digital) (digital)(d & a)
THD
PWM versus PDM
![Page 44: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/44.jpg)
Chun-Hsien Su 44
Class-D Amplifier
Gate Driver
M
Audio source
Dual noise-shaper architecture
+-
Digital
- Simple, almost all digitized
m-bitAD
WaveformRepresent
Grouping
Interpolator Noise Shaper
1/m-bitDAC
CTfilter
Class AB/Class DAmplifier
SpeakerPCM
Interpolator Noise Shaper
Class DAmplifier
SpeakerPCM
![Page 45: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/45.jpg)
Chun-Hsien Su 45
Conclusion
– All-digital Sigma-delta class-D Future work.
– Highly efficient Class D amplifiers now provide similar performance to conventional Class AB amplifiers - If key components are carefully selected and the layout takes into account the subtle, yet significant impact due to parasitic components.– Constant innovation in semiconductor technologies helps the growing Class D amplifiers usage due to improvements in higher efficiency, increased power density and better audio performance. Trends in class-D: half-bridge filterless scheme, analog-feedback loop to improve performance.
![Page 46: Design of Class-D Audio Amplifiers](https://reader033.fdocuments.net/reader033/viewer/2022061418/568145f5550346895db2fb06/html5/thumbnails/46.jpg)
Chun-Hsien Su 46
References[1]. M. Berkhout, “An integrated 200-W Class-D audio amplifer,” IEEE J. Solid-State Circuits, vol. 38, pp. 1198–1206, July 2003.
[2]. H. Ballan, M. Declercq, and J. U. Duncombe, “12 V - Class-D amplifier in 5 V CMOS technology,” in Proc. IEEE CICC, 1995, pp. 559–562.
[3]. E. Dallago, “Advances in high-frequency power conversion by deltasigma modulation,” IEEE Trans. Circuits Syst. I, vol. 44, pp. 712–721, Aug. 1997.
[4]. Marco Berkhout, “An integrated 200 W class-D audio amplifier,” IEEE J. Solid-State Circuits, vol. 38, no. 7, pp. 1198–1206, Jul. 2003.
[5]. Jun Honda and Jorge Cerezo, IRA Technical Report.