Design Development for Shipwreck Kiosks Subm iss on date ... · Design Development for Shipwreck...
Transcript of Design Development for Shipwreck Kiosks Subm iss on date ... · Design Development for Shipwreck...
Design Development for Shipwreck Kiosks
Submission date: February 15, 2019
100% Design Package
Drawing Index
Kiosk Exhibit Master PlanHorton Gallery / Lighthouse Tower
Bow Station Exhibit100
FinishesFinish samples
PROJECT #010919-02 A SHEET: INDEX1/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
INDEX
Hull Station Exhibit200
Stern Station Exhibit300
301
Cargo Station Exhibit400
Kiosks Space Views500
501
Wood Crates600 - Small
601 - Large
Silt Station602
603
604
Mussel Station605
Reader Rails606
Kiosk Station607
608
Cold Interactive Station609
610
Platforms / landforms700 - Bow
701 - Hull
702- Stern
703 -Cargo
Notes
Vendor Cut Sheets
Ship Frames800 - Bow frame
801 - Hull frame
802 - Hull case details
803 - Stern frame
804 - Stern interactive
805 - Cargo frame
PROJECT #010919-02 A SHEET: FINISHES1/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
FINISHES
PL-1 PL-2
1. Ingress / egress through elevators only. Verify openings.
2. Contractor to coordinate outlet locations within space(s).
3. All scenic finishes with Matte clear topcoats.
4. Contractor to provide weathered / distressed finish samples prior to fabrication
5. Art & illustrations shown in this package for placement only. Final art TBD by DCMM.
6. All wood edges w/ 3/16" radius or bevels - no sharp edges or corners.
7. All lighting to be LED.
PL1 FORMICA GRAPHITE #837-58
PL2
FINISH SCHEDULEGENERAL NOTES
PLASTIC LAMINATES
WD-1 GRAYED HEARTPINE WOOD OR EQUIVALENT - WEATHERED & DISTRESSED
WOOD
S-1 SHIP HULL - WEATHERED & DISTRESSED WOOD GRAIN FINISH. MATTE CLEAR TOPCOAT
SCENIC
WD-1
REFERENCE IMAGES ONLY
S-1ACR-1 ACR-2
FORMICA SURF #923-58
S-2 SAND & PAINT MIXTURE - APPLY TO SCULPTED FOAM SAND LANDFORM. MATTE CLEAR TOPCOAT
ACR-1 ACRYLITE ENDLIGHTEN ACRYLIC SHEET
PLASTICS
ACR-2 FROSTED ACRYLIC DIFFUSER
DP-1 DIRECT PRINT TO EXPANDED PVC SUBSTRATE (SINTRA)
GRAPHIC PRINTS
S-2
WD-2 WARM TONE HEART PINE OR EQUIVALENT - WEATHERED & DISTRESSED
WD-2
Bow station 01
Hull station 02
Cargo station 04
Stern Station 03
PROJECT #010919-02 A SHEET: PLAN1/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
KIOSKS FLOOR PLAN
HORTON GALLERY1
SCALE: FEET
20 1 3
100%
KIOSKS EXHIBIT PLAN
KIOSKS FLOOR PLAN
LIGHTHOUSE TOWER2
Bow station 01Hull station 02
Stern Station 03
Cargo station 04
= 1'-0"
9'-5 5/8"
5'-3
7/8"
6'-6
1/2"
7'-8
1/2"
Station ID marker - clear acrylic paneledge-lit below w/ LED's
PROJECT #010919-02 A SHEET: 1001/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
A FRONT ELEVATION BOW STATION 01
SHIPWRECK KIOSKS
PERSPECTIVE VIEW - BOW STATION 01
SHIPWRECK KIOSKS
PLAN - BOW STATION 01
SHIPWRECK KIOSKS1 A
2
Textured sand landform Broken ship bow section
SCALE: FEET
20 1 3
Show general construction elements of ship's bow section
Main mast, hull rib, floor, hull section
100%
Distressed, weathered wood finish throughout
Graphics, art shown for placement only
BOW STATION 01
GR-10
GR-10
GR-10 - Hull design infographic panel - 30" W x 15" T x 3/4" Thk
GR-11 - Ship Construction reader rail - 14" W x 11 1/2" T x 3/4" Thk
GR-11
GR-11
Wooden crate embedded in sand
PL1
DP-1
S-2
S-2S-2
S-1
S-1
PROJECT #010919-02 A SHEET: 2001/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
A FRONT ELEVATION HULL STATION 02
SHIPWRECK KIOSKS SCALE: FEET
20 1 3100%
ASound DomeBrown Innovations
Textured sand landform
10'-4 3/8"
7'-2 3/8"
Ship's side hull section partially sunk in sand
Distressed, weathered wood finish throughout
PLAN - HULL STATION 02SHIPWRECK KIOSKS
1
PERSPECTIVE -HULL STATION 02SHIPWRECK KIOSKS
2
Graphics, art shown for placement only
HULL STATION 02
GR-21 - Why Ships Sink infographic panel - 30"W x 15" T x 3/4" Thk
INT-22 - Interactive station - What Happened to Sink this Ship? Touch monitor
Electrical run within mast element
Station ID marker - clear acrylic paneledge-lit below w / LED's
INT-22 - Short Video - What happenedto Sink this Ship?
GR-21
Wood crate embedded in sand
8'-3
7/8"
AR-23 - Artifact case - internally lit - artifacts TBD
2'-9
7/8"
AR-23
REV1 (2/6/19)
GR-21
PL1
S-1
S-1
S-2
DP-1
PROJECT #010919-02 A SHEET: 3001/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
B REAR ELEVATION STERN STATION 03
SHIPWRECK KIOSKS
SCALE: FEET
20 1 3
100%
B
Wood crate embedded in sand Ship's side hull section partially sunk in sand
Distressed, weathered wood finish throughout
PLAN - STERN STATION 03
SHIPWRECK KIOSKS1
Graphics, art shown for placement only
A
A FRONT ELEVATION STERN STATION 03
SHIPWRECK KIOSKS
Faux rock
GR-31 - Why Great Lakes Shipwrecks are Different panel - 30" W x 15" T x 3/4" Thk
GR-32 - Silt infographic panel - 14"W x 11 1/2" T x 1/4" thk
GR-33 - Identify this Shipwreck graphic 18"W x 9"T x 3/4" thk
GR-34 - Mussel reader rail with specimens in round acrylic tube flush with graphic surface 20"W x 11" T x 3/4" thk
GR-35 - Silt station graphic describes activity above 18"W x 9" T x 3/4"thk
STERN STATION 03
GR-31 GR-32
INT-36 - Interactive station - cold pipe experience- Visitor wraps hand(s)around vertical pipe to feel how cold the Great Lakes water can be
INT-37 - Interactive station - Shipwreck Name Reveal. Flip up weathered panel to reveal name.
INT-38 - Silt activity - Spin container(s) to see simulation of silt settling. Back-lit scene.
INT-36 REV 1 (2/6/19)
8'-10 9/16"
6'-2"
6'-8
1/8"
6'-0
5/8"
GR-33
GR-34
GR-35
INT-37
INT-37
INT-38
INT-38
GR-35
INT-36
INT-38
GR-35
GR-31
GR-33
S-1S-1
S-2
S-2
PERSPECTIVES - STERN STATION 03
SHIPWRECK KIOSKS2
PROJECT #010919-02 A SHEET: 3011/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
Graphics, art shown for placement only
STERN STATION 03
REV 1 (2/6/19)
Acrylic cylinder with mussels sits within reader rail.LED lighting within cylinder.
PROJECT #010919-02 A SHEET: 4001/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
A
PERSPECTIVE CARGO STATION 04
SHIPWRECK KIOSKS
SCALE: FEET
20 1 3
100%
A
Cross section of ship hull partially sunk in sand
Distressed, weathered wood finish throughout
Station ID marker -clear acrylic paneledge-lit below w/ LED's
PLAN - CARGO STATION 04
SHIPWRECK KIOSKS1
Graphics, art shown for placement onlyFRONT ELEVATION CARGO STATION 04
SHIPWRECK KIOSKS
GR-40 - Great Lakes Cargo introduction
GR-41 - Illustration of cargo types inside hull - background
GR-43 - Cargo weights and transportation infographic 18"W x 9"T x 3/4" thk
CARGO STATION 04
INT-44 - Interactive station - Cargo reveal activity
INT-44
Open door to reveal cargo
2
GR-40
GR-41
GR-43
5'-4
1/8"
Ship hatch
GR-40
GR-43
REV 1 (2/6/19)
9'-3 1/4"
6'-3 7/16"
2'-111/2"
4'-6"
S-1
S-2
S-2
S-1
S-2
Paint broken edge dark gray
DP-1
PROJECT #010919-02 A SHEET: 5001/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%Graphics, art shown for placement only
LIGHTHOUSE TOWER VIEWS
REV 1 (2/6/19)
PROJECT #010919-02 A SHEET: 5011/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%Graphics, art shown for placement only
LIGHTHOUSE TOWER VIEWS
REV 1 (2/6/19)
1'-1"
1'-1"
1'-1"
PROJECT #010919-02 A SHEET: 6001/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
PLAN - SMALL CRATES
SHIPWRECK KIOSKS1
100%
WOOD CRATES
Soft-close hingesfor overlay doors
Location - Cargo Station 04
Build 4 pcs (Coal, Iron Ore, Limestone, Lumber)
FRONT - SMALL CRATES
SHIPWRECK KIOSKS2
Spring / bungee to self-close doors
Cargo samples in crateSecure to crate
1 1/2" x 1 1/2" heartpine orreclaimed lumber - corners
SIDE - SMALL CRATES
SHIPWRECK KIOSKS3
All crates - weathered and distressed finish to resemble old crates
15/8"
1/2" thick heartpine orreclaimed lumber slats
1 1/2" x 1 1/2" heartpine orreclaimed lumber - corners
1/2" thick heartpine orreclaimed lumber slats
LED light inside crate to illuminate cargoSuperbrightleds.com #LBFA-xW12-V3
WD-1
WD-1
INT-44
1'-6"
1'-6"
1'-6"
PROJECT #010919-02 A SHEET: 6011/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
PLAN - LARGE CRATES
SHIPWRECK KIOSKS1
100%
WOOD CRATES
Location:Bow Station 01 = 1 pcHull Station 02 = 1 pcStern Station 03 = 2 pcs
Build 4 pcs
FRONT - LARGE CRATES
SHIPWRECK KIOSKS2
1 1/2" x 1 1/2" heartpine orreclaimed lumber - corners
SIDE - LARGE CRATES
SHIPWRECK KIOSKS3
All crates - weathered and distressed finish to resemble old crates
1/2" thick heartpine orreclaimed lumber slats
21/4"
WD-1
WD-1
Silt Station method of operation:Spinning left disc with silt, visitor can see how murky water gets. Will take all day to settle.Since settling will take long w/silt, we demonstrate using sand in the right side disc.Graphic communicates that this reflects a sped up and magnified demonstration of settling silt.
6'-6
7/16
"
2'-2 9/16"
10 3/4"
10"3'-5
7/8"
1"1'-3
3/4"
1'-0"
6"
1'-9"
SCALE: FEET
20 1 3
PROJECT #010919-02 A SHEET: 6021/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
PLAN - SILT STATION
SHIPWRECK KIOSKS1
100%
SILT STATION
Spinners - direct print graphic1/2" Sintra panel
FRONT - SILT STATION
SHIPWRECK KIOSKS2
SIDE - SILT STATION
SHIPWRECK KIOSKS3
Content
GR-35 - Silt activity infographic
Support post
Sediment containers behind discs.See Silt Method of operation Si
lt10
x
Silt
Sand
1'-0 1/2"
2'-103/4"
45°
2'-5"
Front discs spin w/sediment specimen
Rear compartment is stationaryand houses LED lights
Wood trim graphic framew/ four removable fasteners
to change content
ACR-1
PL1
PL1
PL-2
WD-2
DP-1DP-1
INT-38
10"o
pening
10x
10x
Silt
1'-1"
3 1/2" opening
Acrylite EndLightenedge-lit acrylic sheet
PROJECT #010919-02 A SHEET: 6031/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
FRONT SILT DISCS
SHIPWRECK KIOSKS1
100%
SILT STATION
Ball bearing turntableMcmaster Carr #18635A52
LED lights for backlighting sediment
Housing
Clear acrylic sediment tankattach to front disc
Front disc3 1/8"
A
SECTION A
SHIPWRECK KIOSKS2
Vinyl graphic onacrylic behind disc
Sand
PL2
Cool white LED strip light#STN-A65K80-A6A-10B5M-24Vwww.superbrightleds.com
Explanation - this activity is enlarged (10X or other)so the visitor can see sediment settling at a sped uppace using sand as the sediment on this side.
Water
Sediment
SpinningOpening to seesediment settle
PROJECT #010919-02 A SHEET: 6041/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
SILT STATION
EXPLODED SILT STATION
SHIPWRECK KIOSKS1
Acrylite EndLighten edge-lit acrylic sheet
GR-35 - Silt activity infographic
Support post to resembleweathered pier post
Front discs spin w/sediment containers
Rear compartment is stationaryand houses LED lights
Wood trim graphic framew/ four removable fasteners
to change content
LED lights
Rear access panel
Remove for sedimentenclosure to spin
Vinyl graphic
Wedge to secure support to acrylic panel
Ball bearing turntableMcmaster Carr #18635A52
Clear acrylic containersw/ silt & sand
1" aluminum tubing weldedto 1/4" alum plate for graphic support
PROJECT #010919-02 A SHEET: 6051/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
MUSSEL STATION
PLAN MUSSEL READER RAIL STERN STATION 03
SHIPWRECK KIOSKS1
GR-34
1'-8"
3'-3"
GR-34 - Mussel reader rail with specimens inround cylinder flush with graphic surface 20"W x 11" T x 3/4" thk
1'-7 3/8"
2" 2 1/2"
30°
1/8" clear acrylic cover
1/8" frosted acrylic diffuser
LED light strips to back-light frosted acrylic diffuser
Housing for mussels- bolts on behind panel
Mussel case below (back-lit)
1'-8"
11"
7"
SCALE: FEET
20 1 3
FRONT MUSSEL READER RAIL STERN STATION 03
SHIPWRECK KIOSKS2
SIDE MUSSEL READER RAIL STERN STATION 03
SHIPWRECK KIOSKS3
3/4" sintra substrate
ACR-2
PL-2 PL-2
WD-2
DP-1
Cool white LED strip light #STN-A65K80-A6A-10B5M-24Vwww.superbrightleds.com
PROJECT #010919-02 A SHEET: 6061/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
READER RAIL
PLAN READER RAIL
SHIPWRECK KIOSKS1
SCALE: FEET
20 1 3
2'-6"
30" W X 15" T
FRONT ELEVATION READER RAIL
SHIPWRECK KIOSKS2
SIDE ELEVATION READER RAIL
SHIPWRECK KIOSKS3
Location - Bow Station 01 , Hull Station 02 , Stern Section 03
Build 3 pcs
1'-11"
3'-5"
45°
Secure to Sand landform
WD-2
DP-13/4" Sintra substrate
PROJECT #010919-02 A SHEET: 6071/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
KIOSK STATION
PLAN KIOSK STATION
SHIPWRECK KIOSKS1
SCALE: FEET
20 1 3
FRONT ELEVATION KIOSK STATION
SHIPWRECK KIOSKS2 SIDE ELEVATION KIOSK STATION
SHIPWRECK KIOSKS3
Location - Bow Station 01 , Hull Station 02 , Stern Section 03
Build 3 pcs
45°
Secure assembly to sand landform
2'-4"
6'-63/8"
3'-6"
10 3/4"
10"
GR-11GR-33INT-22
Support post to resembleweathered pier post
Ship
Con
stru
ctio
nKiosk nameVinyl applique
Introduction
Wedge to secure roundpost to acrylic panel
Wood trim graphic framew/ four removable fasteners
to change content
1" aluminum tubing weldedto 1/4" alum plate for graphic support
1'-2"
111/2"
15" ELO 1598L touchscreenDirect print graphic
1'-6"
9"
Direct print graphic
1 1/2" hardwood trim frame w/ 1/8" beveled edges typ.
Fasteners (black)
GR-11 GR-33
INT-22
1'-51/2"
WD-2
WD-2
ACR-1
PL1
PL1
PL1
PROJECT #010919-02 A SHEET: 6081/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
KIOSK STATION
FRONT ELEVATION KIOSK STATION
SHIPWRECK KIOSKS1 SIDE ELEVATION KIOSK STATION
SHIPWRECK KIOSKS2
Ship
Con
stru
ctio
n
Alum extrusion for edge-light. Typical.#KRAV-810 (.41") www.klusdesign.com
Acrylic
Blue LED strip light#STN-BBLU-A6A-10B5M-24www.superbrightleds.com
Alum extrusion for edge-light.#KRAV-810 (.41") klusdesign.com
PROJECT #010919-02 A SHEET: 6091/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
COLD PIPE STATION
PLAN COLD PIPE STATION
SHIPWRECK KIOSKS1
SCALE: FEET
20 1 3
FRONT ELEVATION COLD PIPE STATION
SHIPWRECK KIOSKS2 SIDE ELEVATION COLD PIPE STATION
SHIPWRECK KIOSKS3
Location - Stern Section 03
Build 1 assembly
45°
Secure assembly to sand landform
2'-4"
6'-63/8"
3'-6"
10 3/4"
10"
GR-32
Support post to resembleweathered pier post
Col
d
Kiosk nameVinyl applique
Wedge to secure roundpost to acrylic panel
Wood trim graphic framew/ four removable fasteners
to change content
1" aluminum tubing weldedto 1/4" alum plate for graphic support
1'-51/2"
WD-2
WD-2
ACR-1
PL1
PL1
PL1
INT-36GR-32 - Silt infographic panel - 14"W x 11 1/2" T x 1/4" thk
INT-36 - Interactive station - cold pipe experience- Visitor wraps hand(s)around vertical pipe to feel how cold the Great Lakes water can be
Dee
p
INT-36Cold metal pipe
Service panel
Condensation BasinSee Detail ASheet 610
PROJECT #010919-02 A SHEET: 6101/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
COLD PIPE STATION
SIDE ELEVATION COLD PIPE STATION
SHIPWRECK KIOSKS1
INT-36
Service panel
Top housing
1/4" aluminum plate
*2" dia. aluminum shaft core*
*Method of operation - Tactile experienceMetal shaft is cooled to temperature equivalent to that of cold lake. (temp no colder than 33 degrees F)Shaft temp can be less cold than actual water since the palms of the hand are sensitive to extremes.Visitor touches shaft to understand how cold the lakes are for divers in shipwreck dives.
*Method of operation - Techical2" aluminum shaft has hollow center.Refrigerant / cold water flows through shaft to make it cold.Thermostat installed to regulate and keep shaft temp constant.Equipment & hardware are stored either in kiosk or in adjacent sand landform.
Service panel
Simple schematic forvisual representation only.Not for construction.
EndLighten Acrylic
Wedge to secure roundpost to acrylic panel
Wood trim graphic framew/ four removable fasteners
to change content
1" aluminum tubing welded to 1/4" alum plate for graphic support
Wedge to secure roundpost to acrylic panel
Refrigerant / cold water
DETAIL A SECTION
Pipe wall3/4" x 3.5" dia. black sintraring w/ interior bevel
Clear silicone to seal at pipe
Condensation basin
Condensation basin collects condensate off pipe
PROJECT #010919-02 A SHEET: 7001/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
DIORAMA SAND FORMS
PLAN BOW PLATFORM
SHIPWRECK KIOSKS1
16"
12"
12"
10"10"
8"8"
6"
6"
4"4" 2"
14"
14"
2"
9'-5 5/8"
5'-3
7/8"
All platforms to be sized for entry / exit into gallery space. Field Verify.
S-2S-2
1'-4"
ELEVATION BOW PLATFORM
SHIPWRECK KIOSKS2
Carve out areas where ship wreck, crates or posts are embedded Bow station
Denotes heights from finished floor
Against gallery wall
See renderings for platform orientation
CONTOUR VIEWS BOW PLATFORM
SHIPWRECK KIOSKS3
Break / soften all hard edges - typical
NOTES:
Create electrical / network chase through platform as req'd
PROJECT #010919-02 A SHEET: 7011/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
DIORAMA SAND FORMS
PLAN HULL PLATFORM
SHIPWRECK KIOSKS1
16.5"
10'-4 3/8"
All platforms to be sized for entry / exit into gallery space. Field Verify.
S-2S-2
ELEVATION HULL PLATFORM
SHIPWRECK KIOSKS2
Carve out areas where ship wreck, crates or posts are embedded Hull station
Denotes heights from finished floor
Against gallery wall
See renderings for platform orientation
CONTOUR VIEWS HULL PLATFORM
SHIPWRECK KIOSKS3
Break / soften all hard edges - typical
NOTES:
2'-9
7/8"
1'-4
1/2"
14"12"
10"
8"
6"4"
2"
14"12"
10"8"
6"4"3"2"
Create electrical / network chase through platform as req'd
PROJECT #010919-02 A SHEET: 7021/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
DIORAMA SAND FORMS
PLAN STERN PLATFORM
SHIPWRECK KIOSKS1
All platforms to be sized for entry / exit into gallery space. Field Verify.
S-2S-2
ELEVATION STERN PLATFORM
SHIPWRECK KIOSKS2
Carve out areas where ship wreck, crates or posts are embedded Stern station
Denotes heights from finished floor
See renderings for platform orientation
CONTOUR VIEWS STERN PLATFORM
SHIPWRECK KIOSKS3
Break / soften all hard edges - typical
NOTES:
12"
10"
8"6"4"
3"
Create electrical / network chase through platform as req'd
1'-2"
8'-10 9/16"
6'-2"
2"
10" 8" 6"4" 2"
12"14"
Elevators
Gallery interior
PROJECT #010919-02 A SHEET: 7031/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
DIORAMA SAND FORMS
PLAN CARGO PLATFORM
SHIPWRECK KIOSKS1
All platforms to be sized for entry / exit into gallery space. Field Verify.
S-2S-2
ELEVATION CARGO PLATFORM
SHIPWRECK KIOSKS2
Carve out areas where ship wreck, crates or posts are embedded Cargo station
Denotes heights from finished floor
See renderings for platform orientation
CONTOUR VIEWS CARGO PLATFORM
SHIPWRECK KIOSKS3
Break / soften all hard edges - typical
NOTES:
12"
Create electrical / network chase through platform as req'd
18"
14"
9'-3 1/4"
2'-111/2"
16"
10"8"
6"
16"14"
12"10"
8"
6"
Against gallery wall
1'-8"
18" 20"
PROJECT #010919-02 A SHEET: 8001/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
SHIP HULLS
PLAN BOW FRAMESHIPWRECK KIOSKS
1
All pieces to be sized for entry / exit into gallery space. Field Verify.
ELEVATION BOW FRAMESHIPWRECK KIOSKS
2
Bow stationSee renderings for reference
NOTES:
4'-103/16
"
3'-3 11/16"
3"3 11/16"
12'-11 5/16"
5'-0"
4'-9
3/8"
7'-7
1/2"
REAR BOW FRAMESHIPWRECK KIOSKS
3FRONT BOW FRAMESHIPWRECK KIOSKS
4
SCALE: FEET
20 1 3
RIB PROFILESSHIPWRECK KIOSKS
5
11'-2 5/16" Mast
Ship ribs
4" diameter porthole
Floor
Hull skin
Mast sectionTaper from 7" dia (base) to 6 1/2" (top)
Debris
CL
OPENOPEN
OPEN OPEN
5'-7
1/4"
6'-10 1/4"
3'-101/16
"
2'-5 11/16"
6'-10" Mast
PROJECT #010919-02 A SHEET: 8011/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
SHIP HULLS
PLAN HULL FRAME
SHIPWRECK KIOSKS1
All pieces to be sized for entry / exit into gallery space. Field Verify.
ELEVATION HULL FRAME
SHIPWRECK KIOSKS2
Hull station
See renderings for reference
NOTES:
RIGHT HULL FRAME
SHIPWRECK KIOSKS3
SCALE: FEET
20 1 3
RIB PROFILES
SHIPWRECK KIOSKS4
Ship ribs
Floor
Artifact case
Mast section - hollow for electrical / audio cablesTaper from 7" dia (base) to 6 1/2" (top)
Internally lit artifact case
3/16" tempered glass
3/4" bezel captures glass
Removable fasteners
Floor
2'-9
7/8"
2"
1'-9 1/4"
A
2 9/16"
12.5°
2'-3"
Hull skin
2'-1
9/16
"
1'-1"
SECTION A
SHIPWRECK KIOSKS2
Artifact case
A
3'-1 15/16"
2'-1
9/16
"
ARTIFACT CASE FRONT
SHIPWRECK KIOSKS1
FRONT ELEVATION
SHIPWRECK KIOSKS3
3/16" Tempered glassw/ rubber gasket perimeter
Black Sintra bezelto capture glass
Rabbet edge 5/16"deep for glass / gasket
Artifacts TBD
Artifact case
LED lights- Midtown 2.0recessed LED w/ swivelwww.ledwaves.com
PROJECT #010919-02 A SHEET: 8021/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
SHIP HULLSAll pieces to be sized for entry / exit into gallery space. Field Verify.
Hull stationSee renderings for reference
NOTES:
SCALE: FEET
20 1 3
Rubber gasket
3/16" Temperedglass
See Detail A
Detail A
Hull Station Sand platform
PROJECT #010919-02 A SHEET: 8031/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
SHIP HULLS
PLAN STERN FRAME
SHIPWRECK KIOSKS1
All pieces to be sized for entry / exit into gallery space. Field Verify.
ELEVATION STERN FRAME
SHIPWRECK KIOSKS
Stern stationSee renderings for reference
NOTES:
SCALE: FEET
20 1 3
Ship ribs
Floor
7'-7 1/8"
3'-5
1/16
"
2'-2
5/16
"
5'-3
7/8"
3'-5
7/16
"
2 1/2"
5.0°
4°
Floor
Ship ribs
Floor
Rudder
Flip panelINT-37
Rudder
4 1/2" diaporthole
Flip panelINT-37
C
A
BD
C ELEVATION STERN FRAME
SHIPWRECK KIOSKSA ELEVATION STERN FRAME
SHIPWRECK KIOSKSB ELEVATION STERN FRAME
SHIPWRECK KIOSKSD
2 1/2"
Stern rib profile
3 1/8"
1'-3 5/8"
4""
3/4" flip wood panel
Direct print 'OPEN'
Side gussets 1/4" alum
Hull skin
Side gussets 1/4" alum
Hull skin
Side gussets 1/4" alum
Bolt to ship hull
Ship identification
screenprinted to hull
PROJECT #010919-02 A SHEET: 8041/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
SHIP HULLS
Stern stationSee renderings for reference
NOTES:
Stainless steel hinge
Bumper
PROJECT #010919-02 A SHEET: 8051/31/19DOOR COUNTY MARITIME MUSEUMw w w . i d e s i g n e x h i b i t s . c o midesign LLC birmingham, al
SHIPWRECK KIOSK STATIONS
DESIGN DEVELOPMENT205.281.4241
100%
SHIP HULLS
PLAN CARGO FRAMESHIPWRECK KIOSKS
1
All pieces to be sized for entry / exit into gallery space. Field Verify.
Cargo stationSee renderings for reference
NOTES:
SCALE: FEET
20 1 3
Ship ribs exposed
Cargo rib profile
2'-1 1/8"
1'-6 1/8"
2'-0 3/4"6'-7 11/16"
4'-0
1/4"
4'-3"
FRONT ELEVATION CARGO FRAME
SHIPWRECK KIOSKS2
LEFT ELEVATION CARGO FRAME
SHIPWRECK KIOSKS3
RIGHT ELEVATION IS THE SAME
5 5/8"
Broken RailingBroken Railing
Ship hatch
Ship hatch
GR-41
Open
Open
3 3/4"
5"
2"
Floor
Floor
Ship hatch
Shipwreck Kiosks
Vendor Cut Sheets
Frequently Bought Together
Product Details
24V For longer continuous runs Up to 32'Can be cut every 4"3M™ Adhesive backingLifetime warranty0100% DimmableSee accessories for controllers, power supplies, connectors, and channels
View more details
This item: 5050 Single
Color LED Strip
Light/Tape Light 24V
In Stock $49.95
Single Color LED
Controller with Dynamic
Modes RF Remote Mini
In Stock $9.95
Mean Well LED Switching
Power Supply LPV
Series 20150W Single
In Stock $39.90
Add all three to Cart Total Price:
$99.80
Speci�cationsSpeci�cations
Brightness 385 lm/ft (1263 lm/m)
Connection Type Pigtail
Dimensions View Dimensional Drawings
Dimmable Yes
IP Rating NonWeatherproof
LED Beam Angle 120 degree
5050 SingleColor LED Strip Light/Tape Light 24V IP20 385 lm/ft Cool White 6500K 196.9in (16.40ft)Part Number: STNA65K80A6A10B5M24V
All specifications are subject to change without notice.
LED Brand Epistar
LED Density 18 LEDs/ft.
LED Lifetime 50000 Hours
LED Quantity 300 LEDs
LED Type 5050 SMD
LED per Segment 6
Lumen 6315 Lumen
Max Run 32ft (10m)
Minimum Cut Length 100mm (3.9in)
Operating Temperature 25~+45 °C (13~+113 °F)
Polarity Sensitive Yes
Standards And Certifications CE, RoHS Compliant, UL Listed
Strip Width 10mm (0.39in)
Suitable for Vehicles No
Type Flexible Light Strips
Voltage 24 VDC
Wire Length 508mm (20in)
All specifications are subject to change without notice.
STNBREDA6A10B5M24V Red 5m (16.4ft) 2.40 A 109 lm/w 58 W 3.5 146 mA/ft
STNBREDA6A10B30M24V Red 30m (98.4ft) 2.40 A 109 lm/w 58 W 3.5 146 mA/ft
STNBGREA6A10B5M24V Green 5m (16.4ft) 2.32 A 113 lm/w 56 W 3.4 141 mA/ft
STNBGREA6A10B30M24V Green 30m (98.4ft) 2.32 A 113 lm/w 56 W 3.4 141 mA/ft
STNBBLUA6A10B5M24V Blue 5m (16.4ft) 2.28 A 115 lm/w 55 W 3.3 139 mA/ft
STNBBLUA6A10B30M24V Blue 30m (98.4ft) 2.28 A 115 lm/w 55 W 3.3 139 mA/ft
STNA65K80A6A10B5M24V 80+ Cool 6500K 5m (16.4ft) 2.28 A 115 lm/w 55 W 3.3 6500 K 139 mA/ft
STNA65K80A6A10B30M24V 80+ Cool 6500K 30m (98.4ft) 2.28 A 115 lm/w 55 W 3.3 6500 K 139 mA/ft
STNA50K80A6A10B5M24V 80+ Cool 5000K 5m (16.4ft) 2.28 A 115 lm/w 55 W 3.3 5000 K 139 mA/ft
STNA50K80A6A10B30M24V 80+ Cool 5000K 30m (98.4ft) 2.28 A 115 lm/w 55 W 3.3 5000 K 139 mA/ft
STNA40K80A6A10B5M24V 80+ Natural 4000K 5m (16.4ft) 2.28 A 115 lm/w 55 W 3.3 4000 K 139 mA/ft
STNA40K80A6A10B30M24V 80+ Natural 4000K 30m (98.4ft) 2.28 A 115 lm/w 55 W 3.3 4000 K 139 mA/ft
STNA30K80A6A10B5M24V 80+ Warm 3000K 5m (16.4ft) 2.28 A 115 lm/w 55 W 3.3 3000 K 139 mA/ft
STNA30K80A6A10B30M24V 80+ Warm 3000K 30m (98.4ft) 2.28 A 115 lm/w 55 W 3.3 3000 K 139 mA/ft
Part NO CRI LED Color Length Current Draw Efficacy WattageTotal
Wattage ColorTemperature
Current Draw PerFoot
STNAxK80A6A10B5M24V 5050 SingleColor LED Strip Light/Tape Light 24V IP20 385 lm/ft
5050 SingleColor LED Strip Light/Tape Light 24V IP20 385 lm/ft
Single Localizer Technical Information
Overview Model for one listener. Perfect for applications requiring maximum audio focus. Provides 80% drop-off from sweet spot under dome to sound heard just outside dome's edge. Gold standard for audio isolation and stereo quality sound.
Isolation 14 dB
Stereo Separation 10 dB
Listening Region 30"H x 12"W x 12"D (0.8m x 0.3m x 0.3m)
Amplifier Minimum: 1 watts continuous per channel Maximum: 50 watts peak per channel
Input Impedance 6 Ohms
Sensitivity 102dB SPL 1 watt, 1 meter@ 1kHz
Frequency Response 150 Hz – 20KHz +/- 2bB* *When using BI amp only
Installation Options PoleMount System
Mounting Height Options From floor to bottom edge of dome:
Sitting listener 6.5* or 7.5 feet (2 or 2.3m)
Standing listener 7.5*, 8 or 9 feet (2.3, 2.4, or 2.7m) *Recommended mounting height
Physical Dimensions Diameter: 32" (.8m) Height: 16" (.4m)
Weight 17lbs. (7.7kg) Shipping Weight: 18lbs. (8.2kg)
BROWN INNOVATIONS, INC. Sales & Marketing: (773) 477-7500
Manufacturing: (617) 357-1000
WWW.BROWNINNOVATIONS.COM
LED Waves, Inc. 4100 1st Ave. Brooklyn, NY 10012 | www.ledwaves.com | 1-800-986-0169 | [email protected]
The Midtown is a bright, dimmable LED recessed light fixture, low-profile enough for a wide range of installations. ETL approved for dry and damp locations, the Midtown is suitable in restrooms, showrooms, elevators, reception areas, and other home, hospitality, or commercial settings. Each fixture is comparable in brightness to a 50 Watt halogen down light.
The Midtown LED recessed light is made in the USA. The LEDs are designed for optimum lumen maintenance while withstanding the stress of high temperatures and operating currents. This is further supported by LED Waves’ exclusive heat sink, which promotes cooling airflow to add years to the life of the unit. Each recessed light comes with a line voltage LED driver for easy installation in your ceiling. For dimming, select the dimmable driver option.
Enjoy year after year of energy savings and beautiful, bright, focused illumination. With a lifespan over 50,000 hours each, these may be the only down lights you'll ever need!
• Gimbal ring allows you to swivel the light source from -30 to +30 degrees.• Lead wires from the LED fixture to the LED driver are about 14 inches long.• Proudly Made in the USA
SpecificationsBrightness: 571 lumens @4000K, 520 lumens @3000K Wattage: 9 Watt Compares to: 50 Watt halogen MR16 LED Chip: High-power white LEDs (3 LEDs) Voltage: Non-dimmable LED driver (LW90-LD-C17021AF-50CM, UL listed, cUL, CE & RoHS approved): 100~240VAC 50/60Hz, Dimmable LED driver: 100~240VAC 50/60Hz Lifespan: 50,000 hours Housing: Aluminum alloy Protection Rating: ETL listed: Standard for Safety for Luminaires (UL 1598), Luminaires (CSA C22.2#250.0), Standard for Safety for Light Emitting Diode (LED) Equipment for Use in Lighting Products (UL 8750) Operating Temperature: -25°C ~ 50°C
Part Numbers (SKUs)
Silver finish
Non-dimmable LED driver
Midtown 2.0 High-Power LED Recessed Light
Silver finish
White finish
Dimmable LED driver(for use with incandescent
dimming switch)LW50-2012-A9-x4S-W3K
Beam angleS = 8°A = 15°B = 30°F = 45°H = 60°
Color temperatureW3K = Warm white (3000K)W4K = Neutral white (4000K)W5K = Cool white (5000K)
Enclosure color(null) = Silver finish-WHT = White finish
LED Waves, Inc., 2018, all rights reserved.
1/1
DATA SHEET KRAV-56 / KRAV-810 LED extrusion – article number 18017 / 18016
2501 27th Ave, Suite F-10, Vero Beach, FL 32960 / United States / Customer Service: [email protected] / (Ph.) 772 321 2260, 772 569 6655
Product characteristics The extrusion is made from high quality, double-anodized aluminum and designed for flexible or rigid LED strips of a width not exceeding 6 mm (KRAV-56 with 5mm thick glass), 8 mm (KRAV-56 with 6mm thick glass) or 10,8 mm (KRAV-810). Thanks to its unique shape it is ideal for edge lighting of glass panes or plastics 5-6 mm (KRAV-56) or 8-10 mm (KRAV-810) thick. It consists of two extrusions, KRAV-D (adapted for the mounting of LED strips) and KRAV-Z (closing extrusion) fitted with double-sided mounting tape and a silicone cord ensuring a good connection of the extrusions after they have been mounted. Clamping of the glass or plastic is achieved by mounting the two extrusions to the glass and pressing them in an even manner. Accessories for the extrusion are dedicated standard end caps made of polypropylene (one set for one side of the extrusion is KRAV-D and KRAV-Z). The KRAV-D end cap has a ‘groove’, and the KRAV-Z end cap has a “pocket” to fill the gap that appears when mounting thicker panels. The end caps can be fitted both before and after the extrusions have been mounted on the panel. In the latter case, KRAV-D end cap is fixed first. The application of the end caps is supposed to protect the extrusion against the ingress of dust and undesirable particles that may cause contamination of the LED strip, degrading the lighting parameters. KRAV extrusion is not a construction profile. Therefore, assembly, suspension or other technical activities related to the panels should be performed using standard elements.
Applications The extrusion with the LED light source is used in edge lighting of glass panes or plastics. It is also ideal for lighting signs, inscriptions and logos. In addition, this extrusion can be used for making lighting fixtures based on the method of edge backlighting used in kitchens and living rooms, as well as galleries and museums. Products related to the Extrusion KRAV-56 KRAV-810 end cap KRAV 56 (24033) KRAV 810 (24028)
silicone rubber (24042)
Technical specification
Ingress Protection Rating IP 20
Available lengths 1 m / 2 m (can be cut to any size)
Material body – aluminum, end cap – polypropylene (PP), rubber – silicone
The Elo 1598L 15-inch open-frame LCD touch display features a slim design and narrow outside dimensions due to the state-of-the-art, energy-saving LED backlight, using less electricity to operate and generating less heat. The 1598L includes a 500 nit high bright display and extended temperature range to 50° C (122° F) making it ideal for factory automation and other instrumentation control applications. With an optional 24 VDC converter kit included with the unit, manufacturers can leverage a common 24V power supply in their design with a single AC connection. This compact touch display is designed for touch with proven Elo expertise and provides stable, drift-free operation with outstanding image clarity and light transmission—for accurate touch responses and vivid images. Instantly grabbing and holding users’ attention, the 15-inch open frame is perfect for kiosks, casino and amusement, retail self-service, and industrial automation environments.
Product Overview The 1598L is available with Elo’s industry-leading AccuTouch® five-wire resistive with single-touch technology
The touchscreen is sealed against dirt, dust and liquids, to simplify integration into the final enclosure Video Interfaces: HDMI, VGA & Display Port
1598L15-inch LCDOpen-Frame Touchscreen
Integrated Touch Commercial Grade 3-Year Warranty
To find out more about our extensive range of Elo Touch Solutions, go to elotouch.com, or call the office nearest you.
Elo reserves the right to change or update, without notice, any information contained herein; to change, without notice, the design, construction, materials, processing or specifications of any products; and to discontinue or limit production or distribution of any products. Elo, the Elo logo, AccuTouch, IntelliTouch, SecureTouch and TouchPro are either trademarks or registered trademarks of Elo Touch Solutions, Inc. All other trademarks are the property of their respective owners. © 2019 Elo Touch Solutions, Inc. All rights reserved. 19011AES00086
North America Tel +1 408 597 8000 Fax +1 408 597 8050 [email protected]
Europe Tel +32 (0)16 70 45 00 Fax +32 (0)16 70 45 49 [email protected]
Asia-Pacific Tel +86 (21) 3329 1385 Fax +86 (21) 3329 1400 www.elotouch.com.cn
Latin America Tel +1 786-923-0251 Fax +1 305-931-0124 [email protected]
Specifications
Model 1598L
Color Black
Active Display Area 11.97" x 8.98" / 304.1mm x 228.1mm
Diagonal 15"
Aspect Ratio 4:3
Dimensions 13.24" x 10.41" x 1.65" / 336.4mm x 264.4mm x 41.9mm
Native Resolution 1024 x 768 at 60, 75 Hz
Other Supported Resolutions 640 x 480 at 60 Hz; 720 x 400 at 70 Hz; 800 x 500 at 60 Hz; 800 x 600 at 56, 60Hz
Number of Colors 16.2 million
Number of Touches Single-touch
Brightness (typical) LCD Panel: 500 nits; AccuTouch: 400 nits
Response (typical) 35 msec
Viewing Angle Horizontal: ±85° / 170°; Vertical: ±85° / 170°
Contrast Ratio 1500:1
On-Screen Display
Accessible through switches on the unit’s tethered OSD Control box.Controls: Menu, Up, Down, Select, Power Settings: Brightness, Contrast, Clock, Phase, H-Position, V-Position, Auto-Adjust, Sharpness, Color Temperature, OSD Timeout, OSD Language, OSD H-Position, OSD V-Position, Recall Defaults, Video Priority, Information, Touch On Sleep ModeLanguages: English, French, Italian, German, Spanish, Simplified Chinese, Traditional Chinese, JapaneseLockouts: OSD, Power
Video
HDMI V1.3 Type A receptacle for HDMI inputAnalog VGA on Female DB-15 connectorDisplayPort V1.1a - Supports later versions of Display Port video inputInput Video Horizontal Sync frequency range: 30 – 60KHzInput Video Vertical Sync (frame rate) frequency range: 50-75Hz
Power
External DC - Optional power brick (sold separately), Adapter input connector: IEC 60320 C14, Adapter input voltage range: 100-240VAC, 50/60HzMonitor input power connector: Coaxial power jack (2.0mm (+0.0 -0.1mm) pin outer diameter, 6.4mm (+/- 0.3mm) barrel inner diameter, 8.8mm (+/- 0.3mm) barrel depth)Monitor input power signal specifications: 12VDC +/- 5%
Power ConsumptionON (monitor + power brick): 14.1WSLEEP (monitor + power brick): 1.5WOFF (monitor + power brick): 0.5W
Temperature Operating: 0° C to 50° C / 32° F to 122° F; Storage: -20° C to 70° C / -4° F to 158° F
Humidity Operating: 20% to 80%; Storage: 10% to 95%
Weight Unpackaged: 6.4 lbs / 2.9 kg; Packaged: 10.36 lbs / 4.7 kg
Shipping Dimensions 17.09" x 14.76" x 6.89" / 434mm x 375mm x 175mm
Mounting Options
75 mm and 100 mm VESA mount 2-hole mounting interface on all 4 sidesFront mount with optional bezel kitRack mount with optional bezel kit See dimensional drawings for details
Warranty 3 years standard
MTBF 50,000 hours demonstrated
Agency Approvals UL, FCC; RCM; cUL, IC; CCC; CE, TUV; VCCI; KCC; CoC; BSMI; CB; RoHS, China RoHS, WEEE
What’s in the Box HDMI Cable, VGA Cable, OSD Remote, Touch USB Cable, Quick Install Guide; “L” (Side Mount) Brackets w/Screws, EEI Label, Japan Class-B TM info sheet
1598L 15-inch Open-Frame Touchscreen
Model Part Number Technology Interface Surface Treatment Video Interface Availability
1598L E126407 AccuTouch Dual serial/USB Antiglare HDMI, VGA & Display Port Worldwide
Ordering Information
Part Number Description
758588-000 1 Year Extended Warranty, 7-inch to 22-inch LCD Touchmonitor
930057-000 2 Year Extended Warranty, 7-inch to 22-inch LCD Touchmonitor
E67295-000 Elo advance unit replacement for touchmonitors
Extended Warranty OptionsPart Number Description
E483757 OSD Remote
E546861 Replacement Cable Kit for 90 Series
E203787 15-inch “L” (Side Mount) Brackets
E323425 15-inch Front Mount Bezel Kit
E295006 15-inch Rack Mount Bracket Kit
E538507 DVI-D to HDMI Cable Kit
E582895 DP to DP Cable Kit
E239980 Power Converter Kit - 24V DC to 12V DC
Optional Peripherals / Accessories
Home k LED Strip Lights & LED Bars k Flexible LED Strip Lights kk 5050 SingleColor LED Strip Light/Tape Light 24V IP20 385 lm/ft1
Frequently Bought Together
5050 SingleColor LED Strip Light/Tape Light 24V IP20 385 lm/ft Blue 196.9in (16.40ft)Part Number: STNBBLUA6A10B5M24V
Product Details
24V For longer continuous runs Up to 32'Can be cut every 4"3M™ Adhesive backingLifetime warranty0100% DimmableSee accessories for controllers, power supplies, connectors, and channels
View more details
Select LED Color: Blue
Select Length: 5m (16.4ft)
Cool 6500K Cool 5000K Natural 4000K Warm 3000K
Whites
Red Green Blue
Colors
5m (16.4ft) 30m (98.4ft)
$54.95 ea.In Stock Volume price as low as $43.96
This item: 5050 Single
Color LED Strip
Light/Tape Light 24V
In Stock $54.95
Single Color LED
Controller with Dynamic
Modes RF Remote Mini
In Stock $9.95
Mean Well LED Switching
Power Supply LPV
Series 20150W Single
In Stock $39.90
Add all three to Cart Total Price:
Trade Show Lighting TV backlighting
24Volt Operation Double The Maximum Run of 12 Volt DC Strip Lights
Longevity LEDs In Strip Light Will Last 50000 Hours or More
Learn
High Output Strip Outputs 5000 Lumens of Cool, Natural, or Warm White Light
p
Dimmable Strip Can Be Dimmed For Varying Levels Of Intensity
Cut Into Strips Can Be Easily Cut Into 6LED Segments
Adhesive Backing Easy Install PeelAndStick Backing
Speci�cationsSpeci�cations
Brightness 385 lm/ft (1263 lm/m)
Connection Type Pigtail
Dimensions View Dimensional Drawings
Dimmable Yes
IP Rating NonWeatherproof
LED Beam Angle p 120 degree
LED Brand Epistar
LED Density 18 LEDs/ft.
LED Lifetime 50000 Hours
LED Quantity 300 LEDs
LED Type 5050 SMD
LED per Segment 6
Lumen 6315 Lumen
Max Run 32ft (10m)
Minimum Cut Length 100mm (3.9in)
Operating Temperature 25~+45 °C (13~+113 °F)
Polarity Sensitive Yes
Standards And Certifications CE, RoHS Compliant, UL Listed
Strip Width 10mm (0.39in)
Suitable for Vehicles No
All specifications are subject to change without notice.
Type Flexible Light Strips
Voltage 24 VDC
Wire Length 508mm (20in)
All specifications are subject to change without notice.
STNBREDA6A10B5M24V Red 5m (16.4ft) 2.40 A 109 lm/w 58 W 3.5 146 mA/ft
STNBREDA6A10B30M24V Red 30m (98.4ft) 2.40 A 109 lm/w 58 W 3.5 146 mA/ft
STNBGREA6A10B5M24V Green 5m (16.4ft) 2.32 A 113 lm/w 56 W 3.4 141 mA/ft
STNBGREA6A10B30M24V Green 30m (98.4ft) 2.32 A 113 lm/w 56 W 3.4 141 mA/ft
STNBBLUA6A10B5M24V Blue 5m (16.4ft) 2.28 A 115 lm/w 55 W 3.3 139 mA/ft
STNBBLUA6A10B30M24V Blue 30m (98.4ft) 2.28 A 115 lm/w 55 W 3.3 139 mA/ft
STNA65K80A6A10B5M24V 80+ Cool 6500K 5m (16.4ft) 2.28 A 115 lm/w 55 W 3.3 6500 K 139 mA/ft
STNA65K80A6A10B30M24V 80+ Cool 6500K 30m (98.4ft) 2.28 A 115 lm/w 55 W 3.3 6500 K 139 mA/ft
STNA50K80A6A10B5M24V 80+ Cool 5000K 5m (16.4ft) 2.28 A 115 lm/w 55 W 3.3 5000 K 139 mA/ft
STNA50K80A6A10B30M24V 80+ Cool 5000K 30m (98.4ft) 2.28 A 115 lm/w 55 W 3.3 5000 K 139 mA/ft
STNA40K80A6A10B5M24V 80+ Natural 4000K 5m (16.4ft) 2.28 A 115 lm/w 55 W 3.3 4000 K 139 mA/ft
STNA40K80A6A10B30M24V 80+ Natural 4000K 30m (98.4ft) 2.28 A 115 lm/w 55 W 3.3 4000 K 139 mA/ft
STNA30K80A6A10B5M24V 80+ Warm 3000K 5m (16.4ft) 2.28 A 115 lm/w 55 W 3.3 3000 K 139 mA/ft
STNA30K80A6A10B30M24V 80+ Warm 3000K 30m (98.4ft) 2.28 A 115 lm/w 55 W 3.3 3000 K 139 mA/ft
Part NO CRI LED Color Length Current Draw Efficacy WattageTotal
Wattage ColorTemperature
Current Draw PerFootp p p
STNAxK80A6A10B5M24V 5050 SingleColor LED Strip Light/Tape Light 24V IP20 385 lm/ft
5050 SingleColor LED Strip Light/Tape Light 24V IP20 385 lm/ft
Accessories & Power SuppliesAccessories & Power Supplies
Accessories Links
Installation Supplies
Most Popular AccessoriesView All Compatible Accessories
Connectors
Installation Supplies
Power Supplies
Controllers
Housings
All Accessories
NUMBERPART
Information in this drawing is provided for reference only.
http://www.mcmaster.com
10.83"Bolt
Circle12.40"
BoltCircle
5/16"-18 Threads6-Places
1/4"-20 Threads6-Places
10.43"ID
12.8"OD0.07"
0.48"
18635A52Aluminum Large-Diameter
Ring-Style Turntable© 2009 McMaster-Carr Supply Company