Design & Communication Graphics - Maynooth...

2013. M80BC

of 9

Coimisiún na Scrúduithe Stáit State Examinations Commission

Leaving Certificate Examination, 2013

Design & Communication Graphics Ordinary Level Sections B and C (180 marks)

Wednesday, 19 June Afternoon, 2:00 - 5:00

General Instructions:

• Construction lines must be shown on all solutions.

• Write the question number distinctly on the answer paper in Sections B and C.

• Work on one side of the drawing paper only.

• All dimensions are given in metres or millimetres.

• Write your Examination number in the box provided on section A and on all other sheets used.

This examination is divided into three sections:

SECTION A (Core - Short Questions)

SECTION B (Core - Long Questions)

SECTION C (Applied Graphics - Long Questions)

• Four questions are presented.

• Answer any three on the accompanying A3 examination paper.

• All questions in Section A carry 20 marks each.

SECTION A

• Three questions are presented.

• Answer any two on drawing paper.

• All questions in Section B carry 45 marks each.

SECTION B

• Five questions are presented.

• Answer any two (i.e. the options you have studied) on drawing paper.

• All questions in Section C carry 45 marks each.

SECTION C

of 9

B-1. The 3D graphic on the right shows a music stand and

conductor.

Fig. B-1 shows an isometric view of a model of the stand.

(a) Draw an elevation of the stand looking in the direction of the arrow.

(b) Draw a plan projected from the elevation.

(c) Draw an end view of the stand.

(d) Draw an auxiliary elevation of the stand, projected from the plan, which will include the true shape of surface A.

SECTION B - Core Answer any two questions from this section on drawing paper

Fig. B-1

Scale 1:1

of 9

B-2. The 3D graphic on the right shows a unit for holding and charging a cordless phone.

Fig. B-2 shows an incomplete isometric projection of the unit. The end view and plan of the unit are also shown in their required positions. (a) Draw the given equilateral triangle abc and the axonometric axes X, Y, and Z.

(b) Draw the end view and plan, positioned as shown.

(c) Draw the complete axonometric projection.

Fig. B-2

Scale 1:1

of 9

B-3. The 3D graphic on the right shows the intersection of a

wall and a pillar.

Fig. B-3 shows the plan and incomplete elevation of the arrangement.

(a) Draw the given plan and elevation of the structure and show all lines of interpenetration.

(b) Draw an end view of the structure.

Fig. B-3

Scale 1:1

of 9

C-1. The accompanying map, located on the back page of Section A, shows ground contours at 5 metre

vertical intervals.

(a) On the drawing supplied, draw a vertical section (profile) on the line AB. (b) The line CD is the centreline of a proposed level roadway which is at an altitude of 55m.

Using side slopes of 1 in 1 for both cuttings and embankments, complete the earthworks on the northern side necessary to accommodate the roadway. (Note: The earthworks on the southern side of the roadway have already been completed.)

Scale 1:1000

SECTION C - Applied Graphics Answer any two questions (i.e. the options you have studied)

from this section on drawing paper

Geologic Geometry

of 9

C-2. The 3D graphic on the right shows a cufflink

which includes a hyperbolic paraboloid surface.

Fig. C-2 shows the plan and elevation of a typical hyperbolic paraboloid surface, ABCD. (a) Draw the given plan and elevation of the

hyperbolic paraboloid surface.

(b) Project an end view of the hyperbolic paraboloid surface.

Structural Forms

Fig. C-2

Scale 1:1

of 9

C-3. The 3D graphic on the right shows a table lamp with a modern

lampshade. The lampshade is open at the top and at the bottom.

The plan and elevation of the lampshade are shown in Fig. C-3. (a) Draw the given views of the lampshade.

(b) Draw a one-piece surface development of the lampshade.

Surface Geometry

Fig. C-3

Scale 1:1

of 9

C-4. Cams are used in motorbike engines, like the one shown in

the 3D graphic on the right.

Fig. C-4 below shows the outline of such a cam.

The cam imparts this motion to an inline knife edge follower:

• 0° to 90° Rise 50mm with uniform velocity • 90° to 180° Dwell • 180° to 360° Fall 50mm with uniform acceleration

and retardation (UAR).

(a) Draw the displacement diagram for the cam.

(b) Draw the cam profile given the following:

• The cam rotates in an anti-clockwise direction • The nearest approach of the follower to the centre

of the camshaft is 30mm • The camshaft diameter is 20mm.

Dynamic Mechanisms

Fig. C-4

Scale 1:1

of 9

C-5. Details of a Clamp Mechanism from the top of a bicycle stand, as shown on the right, are given in Fig. C-5 below. A 3D graphic of the individual parts is also shown as well as a tabulated parts list.

Draw the sectional elevation A-A of the assembled Clamp Mechanism.

(All chamfers are 2mm×2mm. Any omitted dimensions may be estimated.)

Assemblies

Scale 1:1

Part Name Qty.1 Bottom Clamp Jaw 1

2 Top Clamp Jaw 1

3 Clamping Screw 1

4 M8 Bolt 1

5 M8 Hex Nut 1

Fig. C-5

BLANK PAGE

BLANK PAGEBLANK PAGE

BLANK PAGE

Design & Communication Graphics - Maynooth...

Documents

Transcript of Design & Communication Graphics - Maynooth...