Demonstration of Plasma Assisted Waste Conversion to Gas
Transcript of Demonstration of Plasma Assisted Waste Conversion to Gas
49th International Conference on Environmental Systems ICES-2019-128 7-11 July 2019, Boston, Massachusetts
Demonstration of Plasma Assisted Waste Conversion to Gas
Anne Meier, Ph.D.1 and Malay Shah2
National Aeronautics and Space Administration, Kennedy Space Center, FL, 32899, USA
Kenneth Engeling3
University of Michigan, Ann Arbor, MI, 48109-2104, USA
and
Katerina Quinn4
University of South Florida, Tampa, FL, 33620, USA
The National Aeronautic and Space Administration Science Technology Mission
Directorate Center Innovation Project at Kennedy Space Center funded a one year
investigation for the development of a DC plasma torch to test the conversion of solid and
liquid mission waste to gas. The volume reduction of mission waste is needed to advance waste
processing for vent gases on board space vehicles and space habitats for long duration
missions. The selected plasma torch operated with an input voltage of 120 VAC and a plasma
pilot arc power of approximately 400 W using air as a baseline carrier gas. To date, the team
has demonstrated early concepts of plasma assisted waste conversion of the following
materials: cotton hygiene material, astronaut clothing, plastics (i.e. polyethylene and nylon),
astronaut food packaging, paper, fecal waste simulant, and degrading plant matter (i.e.
inedible biomass waste). The reactions took place in a quartz cylindrical test cell, where waste
was loaded into a quartz crucible and monitored with optical video. The initial reactions
included a multi-stage process that was primarily plasma combustion. The reaction product
gas was qualitatively and quantitatively analyzed with a gas chromatograph and Fourier
transform infrared spectroscopy instrument. The initial results of the system show the volume
reduction from solid to gas in the form of useful products such as carbon monoxide, carbon
dioxide, methane and light hydrocarbons. This paper will discuss the project development and
results regarding waste conversion, power performance and volume reduction for a plasma
space waste processing system.
Nomenclature
AC = Alternating current
Al = Aluminum
Ar = Argon
CH4 = Methane
C2H4 = Ethylene
C2H6 = Ethane
CIF = Center Innovation Fund
CO = Carbon monoxide
CO2 = Carbon dioxide
1 Analytical Laboratories Branch Lead, Laboratory, Development & Testing Division, Mail Stop NE-L3. 2 Mechanical Engineer, Engineering Analysis, Mail Stop NE-XY. 3 Ph.D. Candidate, Department of Nuclear Engineering and Radiological Sciences. 4 B.S. Student, Department of Chemical and Biomedical Engineering.
International Conference on Environmental Systems
2
COTS = Commercial Off the Shelf
Dry GC = Dry golden cherry tomato biomass
Dry GD = Dry golden dwarf tomato biomass
EVA = Extra vehicular activity
FP = Food Packaging
FTIR = Fourier Transform Infrared Spectroscopy
GC = Gas chromatograph
H2 = Hydrogen
He = Helium
HDPE = High density polyethylene
ISS = International Space Station
JSC = Johnson Space Center
K = Kelvin
Kg = Kilogram
KSC = Kennedy Space Center
kVA = Kilovolt-ampere
LEO = Low earth orbit
MAG = maximum absorbency garment
MSW = Municipal solid waste
N2 = Nitrogen
NASA = National Aeronautics and Space Administration
OES = Optical emission spectroscopy
SBIR = Small Business Innovative Research
SLMP = Standard liters per minute
STMD = Science Technology Mission Directorate
Syngas = Synthetic gas
TCD = Thermal conductivity detector
TGA = Thermal gravimetric analysis
US = United States
VAC = Volts AC
W = Watts
I. Introduction
The National Aeronautics and Space Administration (NASA) Science Technology Mission Directorate (STMD)
Center Innovation Fund (CIF) Project at Kennedy Space Center (KSC) funded a one year investigation for the
development of a reactor utilizing a DC plasma torch to test the conversion of solid and liquid mission waste to gas.
Advanced waste processing technologies are necessary to reduce the overall volume of solid mission waste on a
crewed spacecraft or habitat by turning it into a safe vent gas. Plasma gasification is theoretically the most ideal
technology to convert waste to a synthetic gas (syngas) or inert gas (such as permanent gases), due to the ionization
of waste and a clean product gas stream. Rather than burn, plasma gasification uses high heat from the plasma to
degrade materials to their basic molecular elemental form. The primary gas products of organics after plasma
gasification are usually H2, CO, CH4, and CO2. Inorganics are melted and reduce to an inert slag. Most logistical waste
on the International Space Station (ISS) produced by astronauts is low in inorganic material. A low power plasma
application is key for novelty of the technology development for plasma waste conversion applications, since power
is a major design constraint for long duration travel on board spacecraft and habitation systems. Here we describe
some of the background of space mission waste, plasma and other low power applications, as well as the
experimentation that took place with a DC plasma torch at KSC to convert various space feedstocks into gaseous
products.
Colonization of other planets, terrestrial bodies, or hotels in space have been frequently discussed from commercial
space ventures. On Earth, municipal solid waste management is one of the most imperative services a city can provide
to its residents, which would likely parallel to large-scale colonization in space. The effects of mismanaging waste
processing culminates in higher costs downstream compared to the initial cost of managing waste properly at
inception. Since waste is often tended to at a local government level, developing countries often spend the largest
portion of budget on solid waste management1. According to the United States (US) Environmental Protection Agency
International Conference on Environmental Systems
3
(EPA), approximately 2.03 kilograms (kg) of municipal solid waste (MSW) are generated per person per day, which
equated to 262.4 million tons in 2015, primarily consisting of paper and plastics2. This MSW value is increasing to
approximately 1.3 billion tons per year and estimated to reach 2.2 billion tons per year by 20251. In the US,
approximately 53% of the MSW is sent to landfills, while 25% is recycled, 13% is combusted for energy recovery,
and 9% is composted. These US statistics do not include the new restrictions of China’s elimination of recycled mixed
plastic programs, which now leaves much of the recycling, formally destined for China, back into US landfills as of
2019. In 2014 China generated approximately 178.6 million tons of MSW3. In general, affluent countries produce
more MSW per capita, and in 2012 some of the highest generation per capita included Switzerland, Denmark, and
Cyprus4. MSW generation has increased from the start of recording the data since 1960 and continues to steadily
increase. MSW includes items such as corrugated boxes, food, yard waste, sofas, computers, tires and refrigerators,
but not everything that is landfilled – such as construction and demolition debris, wastewater sludge or non-hazardous
industrial waste – is reported and captured in the MSW values.
Waste reduction and conversion techniques are not only imperative for Earth based landfill reduction and waste
management, but will also be imperative for sending humans beyond Low Earth Orbit (LEO) for Space Missions,
especially for future colonization. For a crew of four on a 1-year mission, a total of ~2,600 kg of crew-related waste
mass including life support system consumables and crew consumables are estimated to be generated5. Waste will
include items such as clothing, hygiene items, food, food packaging, food storage containers, extra vehicular activity
(EVA) and medical supplies, feces, brine (urine, sweat), and life support system supplies. It has been previously
described how NASA is investing in technologies6 to down select for future outpost waste conversion systems, as well
as scenarios for different waste management schemes at various space destinations7,8. Plasma for waste conversion
has only been recently introduced and considered for this space application9. We still seek to convert waste from solid
to gas for safe venting or as fuel generation in this plasma application.10
Traditional thermal waste processes typically include gasification, incineration, and pyrolysis. Incineration
temperatures can reach up to 1,500 ºC, where a series of ignition, complete oxidation, neutralization, condensing and
ash generation occurs. The primary product of incineration on the industrial level is usually heat generated from the
cooling process that creates steam to generate electricity and is one of the lowest efficiencies in the thermal process at
~35%4. Pyrolysis uses limited or no oxygen and has one of the highest efficiencies of thermal utilization between 80-
90%, but a low gas yield at less than 40% (i.e. using biomass) due to high tar vapor production11. Temperatures can
reach approximately 900 ºC during pyrolysis, with primary products as hydrocarbons, but have the disadvantage of
producing harmful byproduct chemicals and are costly at the industrial scale to clean up. Gasification can range from
600 to 1,100 ºC to produce syngas for electrical and heat energy. The partial oxidation process of gasification must
maintain high temperature to avoid dangerous formation of dioxins, furans, polychlorinated biphenyls (PCBs), and
other catastrophic and harmful compounds that form below the reaction temperature. Plasma has gained more attention
recently in combination with gasification and combustion as it can destruct solids into syngas products, while forming
the inert slag material.
Plasma is sometimes referred to as the fourth state of matter with two general classifications: non-thermal and
thermal plasma. Plasma consists of electrons, excited atoms, ions, radicals, photons, and neutral particles. Non-thermal
(non-equilibrium) plasma contains electrons with higher energy than the surrounding particles whereas the
temperature of thermal plasma is near unity12. High temperature, thermal plasmas are typically utilized in solid waste
conversion in a single-stage or two-stage system. The plasma components of the single-stage system includes the
plasma torch and reactor chamber, while a two-stage system employs a secondary plasma treatment after the waste
gasification. The second stage is to finalize conversion of the crude gas products. North America, Europe, and Asia
all have plants utilizing thermal treatment facilities that process waste on a municipal level, with facilities that were
commissioned as early as 199713.
Plasma treatment has been applied to space applications. For example, Marshall Spaceflight Center utilized the
Small Business Innovative Research (SBIR) contracts to develop a microwave plasma pyrolysis application to recover
H2 from the ISS Carbon Dioxide Reduction Assembly that vents CH4, and to also assist in removal of accumulated
carbon and carbonaceous build-up using CO2 gas with the plasma system14. The system demonstrated a single-pass
CH4 conversion efficiency of over 90%, but only ~17% chemical energy efficiency for CH4 to acetylene and H2. The
microwave plasma application was last reported to be ongoing for continued testing for both CH4 processing and CO2
plasma cleaning to remove carbonaceous material due to favorable results. Laboratory and municipal scale plasma
systems for waste conversion applications are in use but still require technology development for power and thermal
optimization. In China, thermal plasma waste conversion technology has been in use since the 1980’s, beginning with
smelting applications and a three face alternating current (AC) plasma torch. Designs shifted in the early 2000’s to
DC torches for plume length and stability. One DC torch utilized conversion of plastics where the primary products
International Conference on Environmental Systems
4
were H2, CO, acetylene, ethane (C2H6), ethylene (C2H4), and solid yield. The solids declined when introducing steam
as an effective medium to produce more gas. The carrier gas in the DC system was N2 and electric power input was
between 26.4-62.5 kVA11. RF torches have been investigated with polymer waste via plasma pyrolysis for gas
productions of H2 and CO. The resulting carbon char was 85% carbon that can be used for reinforcing carbon black13.
CH4 to methanol has been successfully reported with plasma using varying reactor designs15. A thermal plasma reactor
achieved single step, non-catalytic selective synthesis of methanol likely due to the dielectric barrier discharge in the
reactor with selectivity of methanol ranging from 40-64%. RF torches have also been demonstrated for biomass
pyrolysis for improvements in thermal energy savings and produced gas mixtures of H2, CO, CH4, CO2, and light
hydrocarbons, which are similar to the products produced in DC thermal plasma11. With such promise on the
laboratory scale for Earth applications, we take plasma conversion and apply it here for space waste conversion
applications.
II. Experimental Design
A. Process Design
The primary goal of this
work was to generate a
laboratory scale proof-of-
concept for DC plasma waste
conversion, starting with
single stream mission waste
materials and increasing to
mixed waste streams. The
experimental flow diagram of
the plasma conversion system
is displayed in Figure 1. The
plasma torch feed gas was air
which entered the plasma
torch where the plume was
generated; waste conversion reactions occurred in a test cell located immediately below the plasma plume. The gas
flow was regulated with an MKS Type 247 4-channel readout connected to a MKS mass flow controller and had a
nominal flow setting of 5 standard liters per minute (SLPM). The effluent gases that resulted from the plasma reactions
continued through a heat exchanger, where water or other condensables (if any) were collected in a vessel. The
remaining room temperature gas passed through a Thermo Fisher Scientific Nicolet iS50 Fourier Transform Infrared
Spectroscopy (FTIR) instrument, equipped with a PIKE Technologies Short-Path Gas Cell. After the FTIR, the gas
was collected and analyzed in a three channel INFICON Micro Gas Chromatograph (GC) Fusion gas analyzer with a
thermal conductivity detector (TCD). The GC data was collected in a tedlar bag that was attached to the output of the
system. The tedlar bag was opened during the plasma reaction and then closed and run in the GC immediately
following the tests. It is important to note that there is significant air dilution for the current reported gas data. All
remaining gases were vented to the laboratory fume hood. The GC column characteristics are listed in Table 1.
Temperatures (T1-T5) were measured with surface probes and in-line K-type thermocouples utilizing a multi-channel
Extech thermometer logger.
Optical emission spectroscopy (OES) measurements were made using a Photon Control Spectrometer SPM-002
coupled with a 200 µm core fiber optic cable that was 2 meters in length. The data was collected using the SpecSoft
V4.0 for Photon Control spectrometers software. The fiber optic was located against the quartz cylindrical housing
and an exposure time of 1 second was set to collect data. Plume characteristics such as gas and electron temperature
were diagnosed using the OES techniques. Visual observations were recorded with a GoPro Hero 6 camera. The video
was used to observe differences in the combustion and gasification process depending upon the selected material.
Table 1. GC Column Characteristics
Module A: Carrier Gas: Ar 99.997%
Column Type: Backflush 1.0 ul, Rt-Molsieve 5 A, 0.25 mm (10m) [Rt-Q-BOND (3m)] TCD2;
Inject time: 30 ms, backflush: 10 s. Heaters: 80 ºC, Pressure: 30 psi, Ramp Temp: 0 sec to 90 ºC, hold for 120 s.
Module B: Carrier Gas: He 99.9999%
Figure 1. Schematic of plasma reactor system.
International Conference on Environmental Systems
5
Column Type: Backflush 1.0 ul, Rt-Molsieve 5 A, 0.25 mm Injector: Inject time: 0 ms, Backflush: 10 s.
Inject time: 30 ms, backflush: 10 s. Heaters: 80 ºC, Pressure: 30 psi, Ramp Temp: 0 sec to 90 ºC, hold for 120 s.
Module C: Carrier Gas: He 99.9999%
Column Type: Variable volume, Rt-Q-Bond, 0.25mm (12m), TCD2
Inject time: 30 ms, heaters: 80 ºC, pressure: 22 psi, Ramp Temp: At Run time: 0s: 65 s, hold time 50 s; At Run time: 50 s: Ramp rate: 1 ºC/s,
135 s, hold time 0 s.
B. Plasma Torch and Test Cell
DC plasma torches are commonly used in academic and scientific plasma research but each torch is operated under
various conditions. The differing operating parameters lead to changes in plasma characteristics. Therefore it was
important to characterize the plasma and the equipment settings. The selected plasma torch was the Plasma Pilot PD-
E-051 from Applied Plasma Technologies, Corporation. The plasma torch operated with an input voltage of 120 VAC
and a plasma pilot arc with power ranging from 50 to 400 W using compressed air as a baseline carrier gas. The torch
had standard fittings to plug into a high voltage terminal line and carrier gas input. The commercial-off-the-shelf
(COTS) parts enabled minimal engineering design and machining for test cell set up. The carrier gas flow may be
varied on this torch, but the standard run parameter was air at 5 SLPM and operated in a continuous high voltage
glow-to-spark discharge. Although 5 SLPM is a high flow rate for considered scale up, at this time the entire system
is in its early stages, and not optimized fully for power and
throughput considerations in depth. The torch data
acquisition was collected with a COTS power supply
(DAT210) featuring constant power mode and compatible
PlasmaView software from Plasma Technics,
Incorporated®. The system was kept in a constant power
output feature which was determined to be ~ 200 W with the
5 SLPM air flow. All waste conversion reactions occurred in
a clear quartz cylindrical test cell with a stainless steel
housing as displayed in Figure 2. The test cell had an inner
diameter of 32 mm and was 35 mm tall. The quartz test cell
was selected for its high temperature properties, and allowed
for observing reactions with the video. The quartz material is
not ideal for insulating the system or for higher temperature
gasification operations. For each experiment, waste was
loaded into the 10 mL quartz crucible with a layer of quartz
wool below the crucible to enable air flow through the
system, and monitored with the video camera. All waste
conversion experiments were run in triplicate, with minimal
variability excluding the high fidelity waste simulant.
C. Waste Simulants and Characterization
The materials studied with this test cell, along with its
starting sample mass, are listed in Table 2 and include items
found as logistical waste on a space mission which have been
previously described in detail regarding composition and
ingredients16. Most waste materials here include the general
majority of mission logistical waste. Food packaging (FP)
was actual space mission food packaging obtained from the
food production laboratory at Johnson Space Center (JSC).
FP contains several layers of polymers and a metallic
(aluminum) layer. The maximum absorbency garments
(MAGs) simulate crew diapers worn on extravehicular
activities and consist of absorptive salts and cotton. In this
series of experiments, a COTS adult diaper was used which
contains sodium polyacrylate as the adsorptive salt. The
MAG experiments were tested in a single waste stream,
Figure 2. Plasma torch and test cell. Left:
Laboratory hardware and experimental set up;
Right: Computer aided drawing of the torch and
test cell.
Table 2. Waste simulants used in experiments and
corresponding mass loading into the quartz
crucible. HDPE = high density polyethylene. FP
= Food packaging, Inedible biomass: Dry GC and
GD.
Waste simulant Starting Mass, g
Cotton (hygiene wipes) 0.50
HDPE 0.50
Nylon 0.50
FP 0.50
Foam 0.25
MAG 0.50
Inedible biomass 0.50
Urine 1.0
Food 2.0
Fecal 2.0
HFWS 1.5
International Conference on Environmental Systems
6
rather than separating the salt and cotton components. The foam material is a proprietary closed cell foam used to pack
and store logistical materials and science experiments safely during launch from Earth. The foam material was
obtained from the JSC Logistics group. As extended habitation of space continues to be explored, sustainable food
sources are needed in order to supplement shipments from Earth. In doing so, plants have begun growth on the ISS
and it is therefore important to examine the feasibility of gasification of inedible biomass. In this work, dry biomass
was obtained from the KSC plant production team. The biomass was reported as maximum absorbency garments
(Golden Heirloom Cherry Tomato plant) and GD (Ground Dew Dwarf Tomato plant from the University of
Minnesota). Each plasma experiment for waste conversion had a starting mass of 0.5 g of waste material, until the
more dense material (i.e. urine, food and fecal simulants, and the high fidelity waste) was tested.
In this work, gasification was intended to take place in the presence of the plasma high temperature plume and
carrier gas ions from air. The waste simulant was diverse and mainly include materials from cellulose and polymer
raw materials, with additions of metallic and salts. The general gasification reaction in air is represented by Equation
1, which proceeds with multiple reactions and pathways.
𝐶𝑥𝐻𝑦𝑂𝑧 + 𝑂2 (21% 𝑜𝑓 𝑎𝑖𝑟) + 𝐻2𝑂 (𝑚𝑜𝑖𝑠𝑡𝑢𝑟𝑒) → 𝐻2 + 𝐶𝑂 + 𝐶𝑂2 + 𝐶𝐻4 + 𝐶𝑐ℎ𝑎𝑟 + 𝑡𝑎𝑟 (1)
Waste simulants were characterized using thermal gravimetric analysis (TGA) via a TGA Q5000 and analyzed
within TA Instruments Universal Analysis 2000 software. The reported data had a ramp setting of 5 ºC per min to 700
ºC.
III. Results and Discussion
A. Waste Characterization
The moisture content for selected waste simulants is displayed in Figure 3. The fecal, food, and urine waste
simulants were greater than 50% liquid.
Otherwise, the majority of waste is dry,
with less than 10% moisture.
The TGA results of selected waste
simulants are shown in Figure 4. The
products undergo much faster
decomposition than the TGA data, but
provide general behavior for
decomposition at varying temperature
markers. For example, materials of
cellulose are expected to convert faster in
the air environment at lower
temperatures, which include the MAG
(white portion of diaper), washcloth, t-
shirt, and MAG (grey portion of diaper).
The materials degrading at higher
temperature contain polymer derivatives,
including the food packaging (Al food),
nylon, polyethylene and packaging foam.
The food packaging (Al food), is not expected to fully decompose as it had aluminum layering that will remain as slag
and solid form in the quartz crucible. The washcloth data terminated at ~480 ºC due to external laboratory air flow
that caused the particles to leave the holding tray during data collection.
B. Visible Observation and Plasma Characteristics
Flow rates of the feed carrier gas were investigated from 2.5 to 50 SLPM to determine the highest achievable
temperature in the quartz cell within the general operating guidelines of the COTS torch in air. The flow rate of 5
SLPM yielded the highest observable system temperature (thermocouple T3) after three minutes of operation. A
sample of the five thermocouple (T1-T5) readings collected during the 5 SLPM empty quartz cell trial is displayed in
Figure 5. At 190 seconds (s), the torch was powered off and temperature declined. Maximum steady-state temperatures
Figure 3. Moisture content of waste simulants.
International Conference on Environmental Systems
7
at the reactor outlet, T3, ranged from 60 ºC
(40 and 50 SLPM) to 285 ºC (5 SLPM).
Gas temperatures increased with a
decreasing flow rate due to the longer
residence time of the plasma within the
discharge region. This was a desired
characteristic for gasification reactions.
The lower flow rates permitted higher
thermal transfer within the discharge
region before thermally neutral particles
entered and absorbed thermal energy. The
5 SLPM flow rate, shown in Figure 6 of the
empty quartz cell test, had the greatest
plume depth of ~12.5 mm into the quartz
cell, and was therefore selected for initial
testing in this work. The plume depth was
important due to the high electron
temperatures within the plasma. Flow rates
below 5 SLPM decreased the plume depth,
and no plume was observed exiting the
torch at flow rates below 2.5 SLPM.
Typical color of atmospheric plasma is
purple due to the abundance of nitrogen,
but the plasma generated by the torch was
observed as purple and blue. A test was
performed without the quartz cell and test
cell apparatus. Within the discharge region
without the test cell (not observable in
Figure 6), the plasma was purple and did
not gain the bluish color. This observation
concluded that the blue plasma evolved
once the test cell was installed and
interaction with the surrounding medium
of the test cell occurred. Product analysis
was therefore important to observe during
empty test cell experiments to use as a
baseline for comparison. The power
consumption of the DC plasma torch for all
of the experimental trials reported here was
consistent at 190 W with some slight variation as the power supply adjusted for the constant power setting.
The electron temperature was calculated from the slope of a Boltzmann line plot using the OES techniques and
was found to be ~ 0.3 eV, or nearly 3227 ºC (3,500 K). The gas temperature analysis and characterization is left for
future work with a collisionally radiative model but is typically on the order of 727 ºC (1,000 K)17. The techniques
involved in obtaining plume characteristics are outside the scope of this paper and will be discussed in later work.
Video screenshots of the waste experiments were obtained for each test. The general behavior included vapor
generation, gasification of the vapor, flame-like combustion, and soot or black char formation on the inner test cell
and quartz crucible walls. The ‘end of reaction’ was validated for each experiment via the emission lines gathered
from OES, in which the intensities returned to background levels. The cotton experiments displayed in Figure 7 capture
the combustion and gasification initialization in the region of the plasma plume. First observations during the cotton
experiment included the formation of a ‘vapor’ cloud throughout the test cell and intense light emission from the
cotton itself. The vapors were not collected as water after the reactor outlet in the heat exchanger, and may have
actually been oil formations. After a few seconds, the vapor dissipated and moisture was seen to collect on the inner
surface of the test cell between the combusting waste within the crucible and the surroundings. After observation of
the moisture, the combustion of the cotton continued with an orange-yellow color for an additional 10 s. Finally, the
plasma plume returned to its baseline colors, indicating the end of the reaction process. The MAGs (Figure 8)
Figure 4. TGA data of a 5°C/min. ramp rate up to 700°C
Figure 5. Temperatures as a function of time during the empty
housing, 180 second trial at 5 SLPM.
International Conference on Environmental Systems
8
performed similarly to the cotton trials in which vapor
was followed by condensation and flame-like
combustion, covering the test cell in soot. The
adsorptive salt may have led to the extended period of
reaction time that was observed visually and with
OES for the MAG material.
During HDPE experiments, the waste material
immediately showed movement due to the extreme
heat exposure. After 2 s of exposure, the volume of
the waste crucible brightened to extreme intensities
and vapor or oils filled the quartz test cell as observed
with cotton. A noticeable difference with HDPE was
that the vapor from the material ignited upon
interaction with the plasma plume and caused further
breakdown of HDPE and significant vapor
accumulation on the test cell surface. After nearly 20
s of plasma interaction, the gas in the test cell
appeared circular in motion, with a rotating flame from the generated waste gas. The rotating flame continued for
about 1 min, and caused soot build-up on the majority of the test cell inner surface. An additional 10 s of reaction
activity was observed by OES. The continued burn after physical waste was no longer visible suggests combustion of
the vapor. The nylon material produced similar results to the HDPE waste with slightly less soot and was excluded
for brevity.
Vapor formation was observed with dry biomass (Figure 8), followed by a simultaneous formation of condensate
and soot formation on the surface of the quartz crucible. The FP material included a vapor cloud formation, followed
by moisture, as the polymer components of the packaging were gasified. The aluminum FP layer did not reach high
enough temperatures to vaporize, and only direct contact with the plume led to slight aluminum slag pooling
formations. The plasma plume was left in operation for 10 min to observe if further thermal heating would occur in
the test cell, but had no success. The plasma plume did interact with the aluminum as an electrostatic charge was
generated, and promoted movement of the clippings in the first few seconds of plasma exposure.
The torch operation time for the fecal simulant was increased to 5 min to ensure a high mass conversion rate. The
time was determined by visual observations and OES data.
Moisture build-up on the inner test cell wall was observed with the food simulant (Figure 9) and the reaction
continued for 3.5 to 4 min. The longer reaction times may be attributed to the density of the material, the increased
starting mass, and the high energy compounds of the simulant. Discovering that the food items have the potential to
react for significantly longer times is important for future optimization. For example, the power of the torch may be
increased to decrease reaction time. T3 was seen to be comparable with the other materials even though the operating
duration was significantly higher. This suggested steady-state had been reached, with energy going into the food
simulant mass as opposed to extra thermal energy.
The HFWS required between 2.5 and 3 min for complete solid conversion. The visual observations were similar
to the food and fecal simulant with the exception of more significant char build-up at earlier time steps than observed
with the fecal or food simulants. Future analysis of the leftover char will provide insight into the byproducts of the
mixed waste and how best to manipulate the plasma in order to sure higher gasification percentage as well as less soot
build-up.
The liquid urine simulant (not shown) pooled at the bottom of the crucible and upon torch plume initiation, and a
significant amount of moisture build-up was observed on the inside of the quartz crucible. The moisture condensed
into small droplets as the operation continued, with crystalline structures remaining in the quartz crucible. The crystal
powder was collected for future elemental analysis and microscopic evaluation. The overall images acquired from the
plasma interaction with the urine simulant had shown stochastic discoloration as plasma interacted with the crystalline
deposits but otherwise remained similar to the empty quartz crucible plasma plume.
Foam material resulted in the fastest vaporization (within the first 4 s of torch utilization) compared to any of the
previously described materials, yet had the lowest average mass reduction. The soot residue generated from the foam
waste remained within the waste crucible with some slag-like material pooling at the bottom.
Figure 6. Plasma plume images into empty quartz housing
as a function of flow rate.
International Conference on Environmental Systems
9
Figure 7. Video screenshots of cotton, HDPE, and nylon experiments to show the start of the experiment (set up) in
the torch off position, the torch initialization (t = 0 seconds), the reaction process, and the final state of the test cell
after all apparent combustion or other thermal reaction is complete.
Figure 8. Video screenshots of the tomato, MAG, and FP experiments.
MAG
Golden Heirloom
Cherry Tomato
Food Packaging
International Conference on Environmental Systems
10
Figure 9. Video screenshots of the fecal simulant, food simulant, and HFWS experiments.
C. Product Analysis
Using the DC plasma test cell for waste conversion, two main product streams were obtained: a combustible gas
and a solid char or soot material. Almost no tars were produced in the process. The product gases consisted of a
mixture of air (left over in excess from the carrier gas) H2, CO, CO2, CH4, C2H4, C2H6 and light hydrocarbons. Char,
a minor product, was observed and collected for the solid conversion calculation. The presence of char however does
demonstrate incomplete conversion of the solid mass during gasification and can likely be further reduced with
improved thermal insulation on the system. Equivalence ratio (ER, ratio of airflow required for stoichiometric
combustion of the mass) will influence the gasification products as well, but contradictions in literature have yet to
convince our team that higher ER to yield higher gas production overall is the best approach18. Higher ERs have also
been shown to decrease the lower heating value and decrease the quality of desired syngas products. In our work, the
lower air flow rate was selected due to the higher temperature values obtained to yield more gasification products.
This can be studied in further detail in future work. The gaseous product distribution during the various waste
experiments at 5 SLPM of air with the plasma torch is summarized in Table 3.
Cotton, HDPE, and Nylon had over 98% solid conversion (gas yield), while food, urine and fecal were over 90%
solid conversion. Since FP contained a layer of aluminum which did not convert to a gaseous product, a lower solid
conversion of about 71% was achieved. The foam, which resulted in the fastest vaporization, had the lowest solid
conversion at 59.57%. In general, these results are encouraging for volume reduction using a plasma source with air
International Conference on Environmental Systems
11
as the working plasma gas. HDPE, FP, fecal and HFWS had the highest observed reaction output temperatures at T3,
which may be due to the high molecular weight (high energy density), and a more efficient ER ratio.
Table 3. Product distribution and solid conversion for waste conversion reactions in plasma test cell. Plasma
working gas = Air at 5 SLPM.
Time delineated FTIR results for foam are displayed in Figure 10. The foam material is a thermoset with
irreversible thermal degradation characteristics that may have been evolving into products not detected by the
calibrated GC, and also unable to reach temperatures high enough for gasification. We do not know the full
composition of the foam material, as it was provided to us by another interested NASA customer for demonstration,
so we are unsure of the potential composition breakdown at this time. Light hydrocarbons were not detected in the
foam material via GC, but FTIR confirmed the presence of hydrocarbons that were higher than carbon double bond
compounds such as cyclic materials. FTIR confirmed the presence of CO, CO2, and CH4 in the gas product stream for
waste materials that had similar observations in GC.
Figure 10. FTIR plot of foam during plasma test experiment with air at 5 SLPM. Confirms the presence of low CO2
production and other hydrocarbon formations.
International Conference on Environmental Systems
12
The HDPE FTIR results confirmed the presence of additional hydrocarbons, while the biomass FTIR confirmed
the presence of permanent gases and ethylene. Time delineated FTIR results for the MAG material is shown in Figure
11, confirming hydrocarbon and CH4 formation.
Figure 11. FTIR plot of MAG during plasma test experiment with air at 5 SLPM.
Particulates did accumulate in the quartz cell and before the heat exchanger lines. Ash materials are typically low
reactive mineral components that decrease the carbon conversion efficiency. Filters were put in line with our system
to prevent particulate from clogging the FTIR or entering the downstream GC.
IV. Future Work
Future work will investigate a variety of fresh biomass and dry biomass, which are important for the in-situ
resource utilization of long-duration space habitation. Further investigation of the by-products of plasma gasification
and combustion will allow for capture, filtration, and re-use of the gaseous compounds. Microscopy and elemental
analysis of solid product formations will take place to confirm ash and soot composition, although assumed at this
time to be highly carbonaceous in composition. The ER can also be manipulated by adjusting the air input into the
system with power adjustments to optimize the reaction parameters. Another future test will include varying the carrier
gases to steam, CO2, and mixed gases (i.e. the syngas product stream). Varying the carrier gas will change the plume
behavior but also help to enable a semi-closed or closed loop system that can integrate with other gases on a spacecraft.
After these additional studies are performed, an energy balance analysis will be performed to evaluate the energy
efficiency of logistical waste treatment using the DC plasma system.
V. Conclusion
The laboratory experiments described here illustrate the possibility of plasma gasification and combustion as an
effective means for waste volume reduction on a spacecraft. The conversion of the solid mass to gaseous products is
enhanced by a slower flow feed gas flow rate so that higher reaction temperatures and longer residence time can be
achieved. Further improvement on the energy efficiency is needed since combustion was a primary reaction result,
and higher temperatures can likely be achieved with additional insulation. The solid mass conversion was over 80%
for most logistical waste products, and greater than 90% solid conversion was achieved for cotton, HDPE, nylon, food,
urine and fecal waste simulant. Product gases from these experiments are useful building blocks for follow-on fuel
and commodity use (H2, CO, CO2, CH4, C2H4, C2H6 and light hydrocarbons). If the product gases are not chosen for
additional use, they are at least observed at this stage for ease of venting off of a spacecraft as permanent gases.
Acknowledgments
The team acknowledges funding from the NASA KSC 2018 STMD CIF as well as funding from the Advanced
Exploration System Logistics Reduction Program at JSC. Many thanks to Dr. Igor Matveev for experimental set up
International Conference on Environmental Systems
13
and technical feedback on results, the Plant group at KSC known as Veggie, Elizabeth Barrios for obtaining TGA
results and Conor O’Bryan for moisture analysis.
References 1 Hoornweg, D., and Bhada-Tata, P., What a Waste: A Global Review of Solid Waste Management, Washington,
DC, USA: Urban Development and Local Government, 2012. 2 US EPA, O., “National Overview: Facts and Figures on Materials, Wastes and Recycling,” US EPA Available:
https://www.epa.gov/facts-and-figures-about-materials-waste-and-recycling/national-overview-facts-and-figures-
materials. 3 Li, J., Liu, K., Yan, S., Li, Y., and Han, D., “Application of thermal plasma technology for the treatment of solid
wastes in China: An overview,” Waste Management, vol. 58, Dec. 2016, pp. 260–269. 4 Sergeev, V. V., Vladimirov, Y. A., Kalinina, K. S., and Kazhukar, E. V., “Gasification and plasma gasification as
type of the thermal waste utilization,” 2016, p. 10. 5 Ewert, M. K., and Broyan, J. L., “Mission Benefits Analysis of Logistics Reduction Technologies,” 43rd
International Conference on Environmental Systems, Charelston, SC: 43rd International Conference on
Environmental Systems, 2013, p. 3383. 6 Anthony, S., and Hintze, P., “Trash-to-Gas: Determining the Ideal Technology for Converting Space Trash into
Useful Products,” 44th International Conference on Environmental Systems, 44th International Conference on
Environmental Systems, 2014. 7 Ewert, M., Broyan, J., Semones, E., Goodliff, K., Singleterry Jr., R., Abston, L., Clowdsley, M., Wittkopp, C.,
Vitullo, N., and Chai, P., “Comparing Trash Disposal to Use as Radiation Shielding for a Mars Transit Vehicle,”
Charleston, South Carolina: International Conference on Environmental Systems, 2017. 8 Linne, D. L., Palaszewski, B. A., Gokoglu, S. A., Balasubramaniam, B., Hegde, U. G., and Gallo, C., “Waste
Management Options for Long-Duration Space Missions: When to Reject, Reuse, or Recycle,” 7th Symposium on
Space Resource Utilization, AIAA SciTech Forum, 2014. 9 Meier, A., Thakrar, P., Shah, M., Johnson, T., Bayliss, J., Hintze, P., Gibson, T., and Captain, J., “Development
of a Micro-Scale Plasma Arc Gasification System for Long Duration Space Mission Waste Processing,” Charleston,
South Carolina: 2017. 10 Burra, K. G., and Gupta, A. K., “Synergistic effects in steam gasification of combined biomass and plastic waste
mixtures,” Applied Energy, vol. 211, Feb. 2018, pp. 230–236. 11 Tang, L., and Huang, H., “Biomass gasification using capacitively coupled RF plasma technology,” Fuel, vol. 84,
Nov. 2005, pp. 2055–2063. 12 Chen, F., Introduction to Plasma Physics and Controlled Fusion, New York, NY: Springer, 2015. 13 Li, J., Liu, K., Yan, S., Li, Y., and Han, D., “Application of thermal plasma technology for the treatment of solid
wastes in China: An overview,” Waste Management, vol. 58, Dec. 2016, pp. 260–269. 14 Wheeler, R., Hadley, N., Dahl, R., Abney, M., Greenwood, Z., Miller, L., and Medlen, A., “Advanced Plasma
Pyrolysis Assembly (PPA) Reactor and Process Development,” 42nd International Conference on Environmental
Systems, San Diego, California: American Institute of Aeronautics and Astronautics, 2012. 15 Zakaria, Z., and Kamarudin, S. K., “Direct conversion technologies of methane to methanol: An overview,”
Renewable and Sustainable Energy Reviews, vol. 65, Nov. 2016, pp. 250–261. 16 Hintze, P., Santiago-Maldonado, E., Kulis, M., Lytle, J., Fisher, J., Lee, J., Vaccaro, H., Ewert, M., and Broyan,
J., “Trash to Supply Gas (TtSG) Project Overview,” American Institute of Aeronautics and Astronautics, 2012. 17 Bibinov, N., Dudek, D., Awakowicz, P., and Engemann, J., “Characterization of an atmospheric pressure dc
plasma jet,” Journal of Physics D: Applied Physics, vol. 40, Dec. 2007, pp. 7372–7378. 18 Kumar, A., Jones, D. D., and Hanna, M. A., “Thermochemical Biomass Gasification: A Review of the Current
Status of the Technology,” Energies, vol. 2, Sep. 2009, pp. 556–581.