Debunking Top 4 Myths of Machine Safeguarding
-
Upload
oci -
Category
Engineering
-
view
64 -
download
7
Transcript of Debunking Top 4 Myths of Machine Safeguarding
![Page 1: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/1.jpg)
February 7, 2017
Debunking theTop 4 Mythsof Machine
Safeguarding
![Page 2: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/2.jpg)
Introduction
Rockford Systems delivers innovative machine safeguarding solutions for organizations working with industrial machinery.
![Page 3: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/3.jpg)
Pervasive Lack of Machine SafeguardingMachine Guarding = OSHA’s Top 10 Most Cited Violations
– According to OSHA, workers who operate and maintain machinery suffer approximately 18,000 amputations, lacerations, crushing injuries, abrasions and more than 800 deaths per year.
– In 2016 alone, 88% of the total number of OSHA Machine Guarding violations were classified as “Serious.”
![Page 4: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/4.jpg)
Pervasive Lack of Machine Safeguarding
• Rockford Systems estimates that an alarming 50% or more of metal fabricating machinery in the United States does not comply with the critical safety requirements for guarding outlined by OSHA and ANSI.
Majority of Metal Fabrication Machines are NOT Guarded
![Page 5: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/5.jpg)
Top 4 Machine Safeguarding Myths
1. New machines are safe (good to go) because their manufacturers sold them as fully compliant with OSHA regulations and other Safety Standards
2. Older machines are exempt from OSHA’s machine safety regulations because they are “grandfathered-
in”3) Automation cells containing Industrial Robots are
always properly safeguarded by the robot supplier
4) OSHA regulations are only guidelines, not the law.
![Page 6: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/6.jpg)
MYTH ONE
![Page 7: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/7.jpg)
New machines are safe because their manufacturers built them to meet up-to-date safety standards and regulations
• REALITY: May not be trueThis depends on the country where the machines were built and
the safety standards that the machine manufacturer used as a guideline for designing, building and installing; control systems, electrical components (NFPA 79-2015), and safeguarding.
It also depends on:1) Machine Safeguarding EXPERTISE of the equipment OEM.2) OEM’s reluctance to add Safeguarding to the project’s COST.3) OEM’s concern about the LIABILITY of providing Safeguarding
![Page 8: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/8.jpg)
New machines are safe because their manufacturers built them to meet up-to-date safety standards and regulations
• REALITY: May not be true (continued)
It's very important for the buyer of new machines to specify the Safety Related Parts of Machine Controls SRP/CS for which this equipment must comply (see ANSI B11.19-2010 as one example). The buyer should not hesitate to spell out the clause numbers from ANSI Standards, European Standards, and even OSHA Regulations, although those are usually older and limited to less machines.
Remember that Safety Standards from European Machinery Guarding Standards (EU) and Canadian Standards Association (CSA) offer higher levels of protection than US ANSI Standards provide.
![Page 9: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/9.jpg)
Example: New Drill Press
![Page 10: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/10.jpg)
Example: New Combination Mill/Drill
![Page 11: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/11.jpg)
OSHA 1910.212 (a)(1) One or more methodsof machine guarding shall be provided to
protect the operator and other employeesin the machine area from hazards such as…
point of operation, ingoing nip points,rotating parts, flying chips, sparks…
Chip/Coolant Hazards
![Page 12: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/12.jpg)
Hinged Chuck Shieldwith built-in Interlock
Example: Engine Lathe with two Shields
Interlock
Chip/Coolant Shieldwith built-in Interlock
![Page 13: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/13.jpg)
www.centryco.comwww.buww.com
Telescopic stainless-steelsleeves cover horizontal
rotating componentsof this Engine Lathe
![Page 14: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/14.jpg)
Example: New “Stamping” Presses
“Servo-Drive”Gap-frame Press
Straight-sideMechanicalPower Press
Two-handControl
AdjustableSide Guards
InterlockedSafety Block
Two Sets ofLight Curtains
Three Sets ofLight Curtains
Fourth in Back?
InterlockedSafety Block
See
our r
ecen
t Blo
g Po
st o
n Sa
fety
Blo
cks
at ro
ckfo
rdsy
stem
s.co
m u
nder
Res
ourc
es;
then
scro
ll to
; Mac
hine
Saf
ety
Bloc
ks
![Page 15: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/15.jpg)
Activ
e O
ptica
l Pro
tecti
ve (L
aser
) AO
PDDe
vice
alo
ng w
ith V
ertic
al L
ight
Cur
tain Example: Hydraulic Press (bending) Brake
Vertical Light Curtain
AOPD Laser Device
Back to Back2-Hand Control
Hinged Corner Guards
Sliding Interlocked Vertical Guard in back
![Page 16: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/16.jpg)
MYTH TWONow that we’ve completed MYTH ONE let’s move on to:
![Page 17: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/17.jpg)
Older machines are "grandfathered-in" since they were manufactured before Safety Standards and Regs. existed
REALITY: Not trueAll machines, regardless of age, must at very least, meet minimum OSHA regulations. (since OSHA was “promulgated” back in 1970)
For companies wanting to meet a higher safety benchmark, the series of 24 ANSI B11 Safety Standards offer the best available guidelines for metal processing machines used here in the U.S.
ANSI B11 standards are regularly updated. Writing Committees must do one of 3 things every 5 years; (re-write, re-affirm, drop/combine)
Machine Safety Compliance that exceeds minimum OSHA Regulations to achieve “Best Safety Practice” (like ANSI B11 Safety Standards) also helps your company meet “due diligence” in case there is ever litigation after a serious machine accident.
![Page 18: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/18.jpg)
There are no OSHAGrandfather
Clauses
Examples: Old Mechanical Power Press, Shear, Lathe
for Older Machines
![Page 19: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/19.jpg)
Belt Cover Open
Belt Cover Closed
On pre-1957 J-headBridgeport VerticalMilling Machines
![Page 20: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/20.jpg)
ANSI B11 Safety Standards for Metalworking Machine ToolsB11.0 Safety of Machinery . . . and Risk AssessmentB11.1 Mechanical Power Presses (1910.217 OSHA) B11.2 Hydraulic Power PressesB11.3 Power Press BrakesB11.4 ShearsB11.5 Iron WorkersB11.6 LathesB11.7 Cold Headers and FormersB11.8 Drilling, Milling, and BoringB11.9 Grinding (1910.215 OSHA) B11.10 SawingB11.11 Gear CuttingB11.12 Roll Forming and Roll BendingB11.13 Automatic Screw/Bar and ChuckingB11.14 Coil Slitting
![Page 21: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/21.jpg)
B11.15 Pipe, Tube, and Shape BendingB11.16 Metal Powder CompactingB11.17 Horizontal Hydraulic Extrusion PressesB11.18 Coil Processing SystemsB11.19 Safeguarding MethodsB11.20 Integrated Manufacturing SystemsB11.21 Machine Tools using LasersB11.22 CNC TurningB11.23 Machining CentersB11.24 Transfer MachinesANSI/RIA R15.06 Robot Safeguarding (both 1999 and 2012)
(con
tinue
d)
TR 1 - 2004TR 2 - 1997TR 3 - 2000TR 4 - 2004TR 5 - 2006TR 7 - 2007
Ergonomics Mist ControlRisk AssessmentPLC/PESNoise MeasurementLean Manufacturing
ANSI B11Technical
Reports
All 24 refer to B11.19
![Page 22: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/22.jpg)
Example: Bench (Pedestal) Grinder
Red Curved Direction Arrow1/4” maximum opening
Covered spindle end/nut1/8” maximum opening
1/8” maximum opening for Work Rest#1 OSHA Machine Safeguarding
violation in every state in the U.S.OSHA 1910.215 (a)(4)
#1
ANSI B11.9-2010ANSI B7.1-2000Also see
“Ring-testing” the wheel before mounting it is required by OSHA
![Page 23: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/23.jpg)
OSHA 1910.215 (b)(3) Abrasive Wheels - Figure 0-6,7 65° from the horizontal plane to the top of opening
and 90° maximum wheel cover opening
![Page 24: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/24.jpg)
1/4”
1/8”Work Rest
TongueGuard
![Page 25: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/25.jpg)
MYTH THREENow that we’ve completed MYTH TWO let’s move on to:
![Page 26: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/26.jpg)
REALITY: May not be trueSome OEMs providesafeguarding andsome don’t
Automation cells containing Industrial Robots are always properly safeguarded by the robot supplier
See our Blog Poston Robots fromearly January
![Page 27: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/27.jpg)
Category 1 well-tried safety components andprinciples
Category B safety-related parts of machineand safeguards – componentswithstand environment
PREV
ENTI
ON
of f
aults
DETE
CTIO
N o
f fau
lts
Category 2 components monitored beforemachine start-up and periodically(mats, drop probe, R/F)
Category 3 dual/monitored system of criticalcomponents – single fault does notlead to loss of safety function
(better guard interlocks)
Category 4 dual/monitored system with allforeseeable faults detected( light curtains)
EN 954-1 Safety-Related Parts of Control Systems(European)
![Page 28: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/28.jpg)
reprinted with permission SICK Inc.
Area Laser Scanner can be programmed on the shop floorwith a laptop for both “Fault Zone” and “Warning Zone”and can be re-programmed if/when parameters change
Perimeter Guarding Heights6 inch sweep, 72 inch height (CSA-2003)
12 inch sweep - 60 inch height (ANSI/RIA-R15.06 1999)
Output Signal Switching Device
Vertical Light Curtain
InterlockedGuard Door
3 EmergencyStop Buttons
![Page 29: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/29.jpg)
MYTH FOURNow that we’ve completed MYTH three let’s move on to:
![Page 30: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/30.jpg)
OSHA Regulations are only safety guidelines for manufacturers but are not really the law
• REALITY: Not trueWilliams/Steiger Act of 12/29/70 (which established OSHA); General Duty Clause 5(a)(1) “Employers to provide a place of employment free from recognized hazards likely to cause death or serious physical harm to employees” (a.k.a. safe and healthful workplace) This applies to states under Federal OSHA supervision, as well as those under State OSHA supervision.
OSHA's Machine Guarding Regulations have changed very little since 1975, therefore lack what employers need to know about current machine safety options. OSHA regs. have always been considered as a starting point only.
By law, employers are legally required to follow OSHA regulations. “COSHOs” (Compliance Safety/Health Officers) issue citations for compliance to their Code of Federal Regulations; CFR SubPart O; Machinery/Machine Guarding
OSHA 1910.212 General Requirements for all machines says the operator and others in machine area must be protected from exposure to hazards. (using Guards, Devices, Methods, or some combination of these three)
![Page 31: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/31.jpg)
OSHA Regulations are only safety guidelines for manufacturers but are not really the law
Once a manufacturer is cited for a violation, whether for new machinery or or old, the best place to turn for advice is the ANSI B11 series of consensus standards that identify accepted options for safeguarding machinery.One of them, ANSI B11.19-2010 entitled; “Performance Criteria for
Safeguarding”, is an "umbrella standard" for all machines in the B11 series. Its primary objective is to establish requirements for the design, construction, installation, operation, and maintenance of safeguarding.
In earlier years, each ANSI B11 Standard had it’s own “Safeguarding Section” which required users to buy copies of ALL the B11 Standards for which they had an interest. In B11.19 -2010, the safeguarding sections of each of the 25 ANSI B11 Standards were consolidated into one (umbrella) standard for user convenience, and to prevent having to buy all of them.
B11.19 is the one to reference for learning about the five Safeguarding alternatives: 1) Guards, 2) Devices, 3) Distance, 4) Location, 5) Opening, regardless of the type of machine that they are applied to.
![Page 32: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/32.jpg)
5(b) EMPLOYEES shall comply with OSHAstandards, rules, regulations, and orders
applicable to their own actions and conduct
EMPLOYERS to furnish a place of employmentfree from recognized hazards likely to causedeath or serious physical harm to employees
OSHA 5(a)(1) General Duty Clause
![Page 33: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/33.jpg)
OSHA 1910.212 General Requirements (a)(1)protect operator & other employees
in the machine area from hazards
• point of operation (Guards, Devices, Methods)• ingoing nip points (Covers, Guards, Shields)• rotating parts (Covers up to 7’ or 8’ from floor)• flying chips & sparks (Chip/Coolant Shields)
examples of safeguarding methods: barrier guards,two-hand actuators, electronic safety devices, etc.
NOT complete list of hazards or safeguarding
![Page 34: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/34.jpg)
General Requirementsfor All Machines
OSHA 1910.212 (a)(3)(ii) . . . The guardingdevice shall be in conformity with any“appropriate standards” . . .
. . . like for instance ANSI B11 Safety Standards,since that is where many OSHA Regulationscame from to begin with (with limitations)?
![Page 35: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/35.jpg)
Code of Federal Regulations OSHA Sub-Part OMachinery and Machine Safeguarding
Verti
cal =
spec
ific1910.213 Woodworking machinery (ANSI 01.1)
1910.214 Cooperage machinery (whiskey barrels)
1910.215 Abrasive wheel machinery
1910.216 Mills and calendars (rubber and plastics)
1910.217 Mechanical Power Presses (ANSI B11.1)
1910.218 Forging machines (presses and hammers)
ANSI B11.9 ANSI B7.1
Horiz
onta
l = g
ener
al
1910.219 Mechanical power transmission apparatus
1910.211 Definitions1910.212 General requirements for all machines
![Page 36: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/36.jpg)
Myt
h Su
mm
ary
• Myth #1: New machines are safe because theirmanufacturers designed and built them to
meet up-to-date safety standards/regulations
– REALITY: Not necessarily, always conduct an Onsite Risk Assessment and/or Machine Survey to identify OSHA 1910.212 “General Requirements for Machines” violations and identify how to bring machines into compliance. ANSI, Canadian and European standards often provide “Best Practices.”
![Page 37: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/37.jpg)
Myt
h Su
mm
ary Myth #2: Older machines are "grandfathered
in“since they were designed and manufactured before safety standards and regulations existed
– REALITY: False, there are no grandfathering laws in effect. All machines must meet minimum OSHA regulations. For companies wanting to meet a higher safety benchmark, ANSI B11 Safety Standards offer the best available guidelines for metal processing machines.
![Page 38: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/38.jpg)
Myt
h Su
mm
ary
• Myth #3: Automation cells containing Industrial Robot are always properly safeguarded by the robot supplier
- REALITY: May not be true some OEM’s provide this and some don’t
• Myth #4: OSHA regulations are onlysafety guidelines but are not the law
- REALITY: False, by law, employers are legally required to follow OSHA regulations, meaning that an OSHA
inspector will issue citations for compliance to the Code of Federal Regulations.
![Page 39: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/39.jpg)
Onsite Machine Risk Assessmentsand Machine Surveys are Critical
Onsite Risk Assessments and Machine Surveys are the critical first step in proper machine safeguarding to help identify the tasks and associated
hazards on a machine shop's equipment.
Risk Assessment based on ANSI B11.0-2015 provides:hazard score with the risk level for each machine suggestions to lower the hazard leveldetailed documentation to outline the results
Machine Survey based on ANSI B11 Stds. and OSHA Regs.each machine is audited for compliance to OSHA Regs. and ANSI Stds.customized proposals with specific products, services to bring the machines into full compliance to OSHA and to “Best Safety Practices”
![Page 40: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/40.jpg)
ANSI B11.0-2015 Table 1Risk Assessment Scoring System
Probability ofOccurrence
of HarmCatastrophic Serious Moderate Minor
Very Likely High High High Medium
Likely High High Medium Low
Unlikely Medium Medium Low Negligible
Remote Low Low Negligible Negligible
Severity of Harm
![Page 41: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/41.jpg)
SUMMARY
![Page 42: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/42.jpg)
Questions & Answers
• Type your question into the chat box
• Email your question to:
![Page 43: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/43.jpg)
Knowledge Is Your Best DefenseJoin Our Webinars:• April 6:
Machine Safety Compliance 101
Attend Our Seminars:• 2 ½ Day “Hands On” Learning
Seminar at HQ Training Center Rockford, Ilinois
February 21, 22, and 23, 2017March 21, 22, and 23, 2017April 18, 19, and 20, 2017May 16, 17, and 18, 2017June 20, 21, and 22, 2017July 18, 19, and 20, 2017August 22, 23, and 24, 2017September 19, 20, and 21, 2017October 17, 18, and 19, 2017November 14, 15, and 16, 2017December, 2017 – No Seminar
REGISTER FOR WEBINARS AND SEMINARS ON WEB SITE UNDER EDUCATION
www.rockfordsystems.com
• June 6:Risk Assessment vs. Machine
Survey: Which is right for your organization?
![Page 44: Debunking Top 4 Myths of Machine Safeguarding](https://reader033.fdocuments.net/reader033/viewer/2022051520/58a2cb051a28ab217a8b6905/html5/thumbnails/44.jpg)
THANK YOU