Dean Brochure High Temp
-
Upload
antonio-velarde -
Category
Documents
-
view
47 -
download
1
Transcript of Dean Brochure High Temp
Process Industries Heat Transfer OEMs, Chemical, Petrochemical, Power Plants, Plastics, Food Processing, Pharmaceutical and Commercial (hospitals, universities, laboratories)
Quality Design Features forHigh Temperature PumpsThe Dean Pump R Series pumps are designed for high pressureand high temperature applications. They include design featuresthat guard against pipe load and thermal distortions. The follow-ing features assure long and trouble free service life of bearings,driver coupling, and shaft sealing devices.
• Centerline mounted pump casing support allows thermalexpansion of the casing about the pump centerline withoutdisturbing shaft alignment
• Centerline mounted pump casing supported with yoke orpedestal mounts (standard on R4180 and R4240) holds thepump securely in place resisting thermal expansion pipingloads (watercooled pedestal mounts also available)
• Centerline suction and discharge connections equalize pipeloads to prevent off center forces and distortion
• Deep precision rabbeted joints on the casing and bearinghousing allow accurate assembly and hold the assembledpump rigidly in line
• Totally confined high temperature casing gasket providessafety during operating service conditions
• Back pull-out construction with spacer coupling allows theentire pump rotating assembly to be removed for servicingwithout removing the casing from the piping or disturbing the driver
• Fully enclosed Francis vane impeller design is keyed to theshaft and secured by an impeller bolt and washer to remainrigidly in place under all load conditions. The design ishydraulically balanced to extend bearing and seal life.Wearing ring clearances (R4000, RM and RMA Series only)are to API refinery requirements for optimum efficiency
• ASME/ANSI B16.5 Class 300 Raised Face or Ring TypeJoint flanges are available for high pressures
• Casing wear rings (R4000, RM and RMA Series only) arestandard and allow renewable running clearances within thepump for extended performance life
• Heavy duty angular contact thrust bearings provide longbearing life
Interchangeability• Maximum pump and parts interchangeability for field repairs
without special tools
• Hydraulic performance curves are the same for each R Seriespump size
Versatility• (R4000 only), pump designs can be fitted with a wide range
of mechanical seals and flush/cooling arrangements, there-by allowing for maximum sealing and installation flexibility
• Air-cooled pump designs requiring no external water coolingfor the bearings and mechanical seal
• Water-cooled designs for maximum mechanical seal life
• Sealless, magnetic drive designs for emissions compliance/concerns (RM/RMA)
• Wide range of hydraulic coverage
• Back pullout design allows for removal of the entire rotatingassembly for easy field repair and maintenance
• Various casing foot designs are available – “yoke” (exclud-ing R4180 & 4240) allows for pump to fit on an ASME/ANSI B73.1 baseplate and Dean’s “Economy” baseplate,“pedestal” allows for pump to mount on an API-type base-plate, and “water-cooled pedestal” for severe service conditions and applications
• Sturdy fabricated steel baseplates help maintain alignmentunder all service conditions
Dean Pump® R SeriesHigh Temperature (Hot Oil/Hot Water) Centrifugal Process Pumps
DEAN PUMP® RM5000 SERIES
Magnetic Drive High Temperature Process Pumps• Capacities to 1,200 GPM (270 m3/hr)• Heads to 600 feet (180 m)• Pumping Temperatures to 400°F (204°C)• Working Pressures to 325 PSIG (2,240 kPa)• Seventeen Sizes
RM5000 Series Pumps are sealless, heavy duty process pumps. Featuresinclude centerline supported casing, silicon carbide bearings positively heldagainst rotation, Samarium cobalt rare earth magnets, and a Hastelloy-Ccontainment shell. Seventeen sizes are available in steel and 316SS.
Head-Capacity Range Charts
1X 2 X 111/2
11/2 X 3 X 111/2
3 X 4 X 10
3 X 4 X 81/22 X 3 X 81/2
2 X 3 X 1011/2 X 3 X 10
1 X 3 X 81/2
11/2 X 3 X 81/2
Two Pole Motor
Four Pole Motor
Working Pressure vs. Pumping Temperature
1X 2 X 111/211/2 X 3 X 111/2
3 X 4 X 10
2 X 3 X 81/2
2 X 3 X 1011/2 X 3 X 10
1 X 3 X 81/2 11/2 X 3 X 81/2
11/2 X 3 X 131/22 X 3 X 131/2 3 X 4 X 131/2
2 X 3 X 111/2 3 X 4 X 111/2
4 X 6 X 111/2
4 X 6 X 10
3 X 4 X 81/2
4 X 6 X 81/2
TOTA
L HE
AD F
EET
–35
00 R
PM –
60 H
ERTZ
TOTA
L HE
AD F
EET
–17
50 R
PM –
60 H
ERTZ
TOTA
L HE
AD M
ETER
S –
2900
RPM
–50
HER
TZTO
TAL
HEAD
MET
ERS
–14
50 R
PM –
50 H
ERTZ
700
600
500
400
300
200
100
0
10009008007006005004003002001000
25 50 75 100 125 150 175
140
120
100
80
60
40
20
PUMPING TEMPERATURE – °F
CAPACITY – CUBIC METERS PER HOUR – 2900 RPM – 50 HERTZ
CAPACITY – CUBIC METERS PER HOUR – 1450 RPM – 50 HERTZ
CAPACITY – U.S. GALLONS PER MINUTE – 1750 RPM – 60 HERTZ
CAPACITY – U.S. GALLONS PER MINUTE – 1750 RPM – 60 HERTZ
200
180
160
140
120
100
80
60
40
20
0
4 6 8 10 20 40 60 80 100 200
40
35
30
25
20
15
10
5
10 100 1000 2000
1000 200 300 400 500 600 700
WOR
KING
PRE
SSUR
E –
PSIG
300
200
100
0
RMA
RM
RM
RMA
RM
DEAN PUMP® R4000 SERIES
Heavy Duty, High Temperature Process Pumps• Capacities to 6,500 GPM (1,476 m3/hr)• Heads to 800 feet (244 m)• Pumping Temperatures to 850°F (455°C)• Working Pressures to 500 PSIG (3,447 kPa)• Twenty-seven Sizes
R4000 Series Pumps are the single most applied pump for high temperature heat transfer service. These heavy duty, centerline supported, chemical, petrochemical, and refinery style process pumpsare available in twenty-seven sizes in steel and 316SS construction.
Head-Capacity Range ChartsTwo Pole Motor
11/2 X 3 X 131/2
2 X 3 X 131/23 X 4 X 131/2
1X 2 X 111/2 11/2 X 3 X 111/2
3 X 4 X 104 X 6 X 10 #1 (R450)
4 X 6 X 81/2
3 X 4 X 81/22 X 3 X 81/2
2 X 3 X 1011/2 X 3 X 10
2 X 3 X 111/2
11/2 X 3 X 81/2
1 X 3 X 81/2
4 X 6 X 10 #2 (R4140)
3 X 4 X 111/2 4 X 6 X 111/2
6 X 8 X 121/2
2 X 4 X 151/2
3 X 4 X 151/2
4 X 6 X 151/26 X 8 X 151/2
8 X 10 X 151/2
Four Pole Motor
R4000
Carbon Steel
316SS
Working Pressure vs. Pumping Temperatureused to determine the allowable working pressure at any allowable processfluid temperature for the material of construction selected
GPM Flow Rate of Cooling Water Based on 70oF (21°C) Inlet Temp
12345
48
111519
GPM
Seal Chamber Temperature vs. PumpingTemperaturewith respect to the GPM of cooling water flowing through the cooling jacketsurrounding the seal chamber.
11/2 X 3 X 131/2
2 X 3 X 131/2
3 X 4 X 131/2
1X 2 X 111/2
11/2 X 3 X 111/2
3 X 4 X 10
4 X 6 X 10 #1 (R450)
4 X 6 X 81/23 X 4 X 81/2
2 X 3 X 81/2
2 X 3 X 1011/2 X 3 X 10
1 X 3 X 81/2
11/2 X 3 X 81/2
TOTA
L HE
AD –
FEET
–35
00 R
PM –
60 H
ERTZ
TOTA
L HE
AD –
FEET
–17
50 R
PM –
60 H
ERTZ
TOTA
L HE
AD –
FEET
–14
50 R
PM –
50 H
ERTZ
SEAL
CHA
MBE
R TE
MPE
RATU
RE –
°F
SEAL
CHA
MBE
R TE
MPE
RATU
RE –
°C
TOTA
L HE
AD –
MET
ERS
–29
00 R
PM –
50 H
ERTZ
WOR
KING
PRE
SSUR
E –
kPa
WOR
KING
PRE
SSUR
E –
PSIG
800
500
400
300
200
100
0
25 50 75 100 125 150 175 200 225 250 275
450400350300250200150100500-50
100
200 300 400
COOLING WATER FLOW RATE °C
500 600 700 800
150 200 250 300 350 400 450
1400
-100 0 100 200 300 400 500 600 700 800 900
1300120011001000900800700600500400
4
100 100010 6000
6 8 10 20 40 60 80 100 200 400 800600
3002001000
1604000
1801/min
160
140
120
100
80
60
40
20
0
3500
3000
2500
2000
1500
1000
500
140
100
120
80
60
40
20
55260
350
300
250
200
150
100
50
240
220
200
180
160
140
120
100
80
60
40
20
0
50
45
40
35
30
25
20
15
10
5
700
600
500
400
300
200
100
0
CAPACITY – CUBIC METERS PER HOUR – 2900 RPM – 50 HERTZPUMPING TEMPERATURE – °C
PUMPING TEMPERATURE – °F
PUMPING TEMPERATURE – °F
Minim
um Te
mper
ature
Limi
t: 20
°F
Carb
on St
eel
Maxim
um Te
mper
ature
316S
S Max
imum
Temp
.
CAPACITY – U.S. GALLONS PER MINUTE – 3500 RPM – 50 HERTZ
CAPACITY – CUBIC METERS PER HOUR – 1450 RPM – 50 HERTZ
CAPACITY – U.S. GALLONS PER HOUR – 1750 RPM – 60 HERTZ
PUMPING TEMPERATURE – °C
DEAN PUMP® RMA5000 SERIES
Magnetic Drive Air-Cooled High Temperature Process Pumps• Capacities to 1,200 GPM (270 m3/hr)• Heads to 600 feet (180 m)• Pumping Temperatures to 750°F (400°C)• Working Pressures to 300 PSIG (2,068 kPa)• Seventeen Sizes
RMA5000 Series Pumps are sealless, air-cooled (or water-cooled), heavyduty process pumps. Features include centerline supported casing, siliconcarbide bearings positively held against rotation, Samarium cobalt rare earthmagnets, and a Hastelloy-C containment shell. Air fin cooling reduces heatflow from process fluid to magnets. Seventeen sizes are available in steel.
Head-Capacity Range Charts
1X 2 X 111/2
11/2 X 3 X 111/2
3 X 4 X 10
3 X 4 X 81/22 X 3 X 81/2
2 X 3 X 1011/2 X 3 X 10
1 X 3 X 81/2
11/2 X 3 X 81/2
Two Pole Motor
Four Pole Motor
RMA5000
Working Pressure vs. Pumping Temperature
1X 2 X 111/211/2 X 3 X 111/2
3 X 4 X 10
2 X 3 X 81/2
2 X 3 X 1011/2 X 3 X 10
1 X 3 X 81/2 11/2 X 3 X 81/2
11/2 X 3 X 131/22 X 3 X 131/2 3 X 4 X 131/2
2 X 3 X 111/2 3 X 4 X 111/2
4 X 6 X 111/2
4 X 6 X 10
3 X 4 X 81/2
4 X 6 X 81/2
TOTA
L HE
AD F
EET
–35
00 R
PM –
60 H
ERTZ
TOTA
L HE
AD F
EET
–17
50 R
PM –
60 H
ERTZ
TOTA
L HE
AD M
ETER
S –
2900
RPM
–50
HER
TZTO
TAL
HEAD
MET
ERS
–14
50 R
PM –
50 H
ERTZ
700
600
500
400
300
200
100
0
10009008007006005004003002001000
25 50 75 100 125 150 175
140
120
100
80
60
40
20
PUMPING TEMPERATURE – °C
PUMPING TEMPERATURE – °F
CAPACITY – CUBIC METERS PER HOUR – 2900 RPM – 50 HERTZ
CAPACITY – CUBIC METERS PER HOUR – 1450 RPM – 50 HERTZ
CAPACITY – U.S. GALLONS PER MINUTE – 1750 RPM – 60 HERTZ
CAPACITY – U.S. GALLONS PER MINUTE – 1750 RPM – 60 HERTZ
200
180
160
140
120
100
80
60
40
20
0
4 6 8 10 20 40 60 80 100 200
40
35
30
25
20
15
10
5
10 100 1000 2000
-50
-100 0 100 200 300 400 500 600 700 800
0 50 100 150 200 250 300 350 400
2000
1500
1000
500
0
WOR
KING
PRE
SSUR
E –
PSIG
WOR
KING
PRE
SSUR
E –
kPa
300
200
100
0
DEAN PUMP® RA SERIES
RA3146/RA3186 PUMPS
RA2096 PUMPS
Working Pressure vs. Pumping Temperature
Air-Cooled High TemperatureThermal Liquid Pumps• Capacities to 1,800 GPM (408 m3/hr)• Heads to 425 feet (130 m)• Pumping Temperatures to 650°F (343°C)• Working Pressures to 350 PSIG (2,413 kPa)• Thirteen Sizes
RA Series Pumps are cost effective, hot oil, heat transfer pumps. Pumpsfeature a shaft mounted fan to provide air flow over the cooling fins ofthe pump. This air-cooled design translates to NO EXTERNAL WATERCOOLING REQUIRED for the bearings and mechanical seal. Thirteensizes are available in ductile iron construction.
No Liquid Cooling RequiredThe air fan-cooled design of RA Series pumps permits temperature drop in the pump from the casing to sealfaces. When pumping at 650°F (343°C), the seal facetemperature is 230°F (110°C). The efficient gradientbreakdown protects the mechanical seal and bearing.
Head-Capacity Range ChartsTwo Pole Motor
Four Pole Motor
11/2 x 3 x 10
2x 3 x10
1x3x81/2
3 x 4 x 10
4 x 6 x10#1
4 x 6 x 81/2
3 x 4 x 81/2
1 x 11/2 x 6
11/2 x 3 x 6
11/2 x 3 x 81/2
4 x 6 x 10#2
1 x 11/2 x 8
2 x 3 x 81/2
3 x 4 x 81/2
11/2 x 3 x 6
4 x 6 x 81/2
3 x 4 x 10
4 x 6 x 10#12 x 3 x 10
11/2 x 3 x 81/2
2 x 3 x 81/2
1x 11/2x 8
1 x 3 x 81/2
11/2 x 3 x 10
1x11/2 x 6
TOTA
L HE
AD –
FEET
–35
00 R
PM –
60 H
ERTZ
500
400
300
200
100
0
CAPACITY – CUBIC METERS PER HOUR – 2900 RPM – 50 HERTZ0 20 40 140 160 180 200 2201201008060
100
80
CAPACITY – U.S. GALLONS PER MINUTE – 3500 RPM – 60 HERTZ
60
40
20
0 TOTA
L HE
AD –
MET
ERS
–29
00 R
PM –
50 H
ERTZ
0 800 1000 1200 1400 1600 1800
0 20 40 60 80 260120
100
80
60
40
20
00 100 200 300 400 500 600
20
15
10
5
0
25
CAPACITY – U.S. GALLONS PER MINUTE – 1750 RPM – 60 HERTZ
CAPACITY – CUBIC METERS PER HOUR – 1450 RPM – 50 HERTZ
TOTA
L HE
AD –
FEET
–17
50 R
PM –
60 H
ERTZ
TOTA
L HE
AD –
MET
ERS
–14
50 R
PM –
50 H
ERTZ
400
300
200
100
0
-50 0 50 100 150 200 250 300 350
-100 0 100 200 300 400 500 600 700
2500
2000
1500
1000
500
0
PUMPING TEMPERATURE – °F
PUMPING TEMPERATURE – °C
WOR
KING
PRE
SSUR
E –
PSIG
WOR
KING
PRE
SSUR
E –
kPa240 260 280 300 320 340
600400200
100 120 140 160 180 200 220 240
700 800 900 1000 1100 1200 1300 1400
DEAN PUMP® RAV SERIES
Vertical Inline Air Cooled High TemperatureThermal Liquid Pumps• Capacities to 360 GPM (82 m3/hr)• Heads to 320 feet (98 m)• Pumping Temperatures to 650°F (343°C)• Working Pressures to 350 PSIG (2,413 kPa)• Six Sizes
The RAV Series offers the same design benefits as the RA Series butin a vertical configuration. Pumps feature a shaft mounted fan to provide air flow over the cooling fins of the pump. This air-cooleddesign translates to NO EXTERNAL WATER COOLING REQUIREDfor the bearings and mechanical seal. Three sizes are available in ductile iron construction.
Working Pressure vs. Pumping Temperature
Head-Capacity Range Charts
PUMPING TEMPERATURE – °C
PUMPING TEMPERATURE – °F
Two Pole Motor
Four Pole Motor
CAPACITY – CUBIC METERS PER HOUR – 2900 RPM – 50 HERTZ
TOTA
L HE
AD –
FEET
–35
00 R
PM –
60 H
ERTZ
CAPACITY – U.S. GALLONS PER MINUTE – 3500 RPM – 60 HERTZ
TOTA
L HE
AD –
MET
ERS
–29
00 R
PM –
50 H
ERTZ
0 10 20 30 40 50 60 70
400360320280240200160120804000
50
100
150
200
250
300
350
0
10
20
30
40
50
60
70
RAV
1X1.
5X8
RAV 1X1.5X6 RAV 1.5X3X6
RAV 1.5X3X8.5
RAV 2X3X8.5RAV 1X3X8.5
CAPACITY – CUBIC METERS PER HOUR – 1450 RPM – 50 HERTZ
TOTA
L HE
AD –
FEET
–17
50 R
PM –
60 H
ERTZ
CAPACITY – U.S. GALLONS PER MINUTE – 1750 RPM – 60 HERTZ
TOTA
L HE
AD –
MET
ERS
–14
50 R
PM –
50 H
ERTZ
0 5 10 15 20 25 30 35
0 20 80 1006040 120 140 2000
20
30
40
50
60
70
80
90
0
2
4
6
8
10
12
16
14
18
10
160 180
RAV 1X1.5X8
RAV 1X1.5X6RAV 1.5X3X6
RAV 2X3X8.5
RAV 1.
5X3X
8.5
RAV 1X
3X8.5
WOR
KING
PRE
SSUR
E –
PSIG
WOR
KING
PRE
SSUR
E –
KPa
--73 -35 3 41 79 117 155 193 231 269 307
-100 0 100 200 300 400 7000
50
250
300
350
400
450
500
0
250
500
750
1000
1250
1500
1750
2000
2250
2500
2750
3000
3250
200
150
100
500 600
RAV 3096 PUMPSRAV 3146 PUMPS
345
DEAN PUMP® RWA SERIES
Air-Cooled Hot Water Pumps• Capacities to 1,800 GPM (408 m3/hr)• Heads to 425 feet (130 m)• Pumping Temperatures to 400°F (205°C)• Working Pressures to 450 PSIG (3,100 kPa)• Thirteen Sizes
RWA Series Pumps are designed specifically for use with hot water,ethylene glycol and propylene glycol in boiler feed, steam condensate,HVAC and heat transfer applications. Pumps feature a shaft mountedfan to provide air flow over the cooling fins of the pump. This air-cooled design translates to NO EXTERNAL WATER COOLINGREQUIRED for the bearings and mechanical seal. Thirteen sizes areavailable in ductile iron construction.
Working Pressure vs Pumping Temperature
Head-Capacity Range Charts
4x6x10x#1
3x4x10
2x3x10
4x6x81/2
3x4x81/2
1x11/2x8
11/2x3x10
1x3x81/2
1x11/2x6
11/2x3x81/2
11/2x3x6
2x3x81/2
Two Pole Motor
4x6x81/22x3x81/2
11/2x3x81/2
11/2x3x10
1x3x81/2
2x3x10
3x4x81/2
11/2x3x6
1x11/2x6
1x11/2x84x6x10#1
3x4x10
4x6x10#2
Four Pole Motor
CAPACITY – CUBIC METERS PER HOUR – 2900 RPM – 50 HERTZ0 20 40 60 120 180 20080 100 140 160 220
500
400
300
200
100
0
TOTA
L HE
AD –
FEET
–35
00 R
PM –
60 H
ERTZ
0 200 400 600 800 1000 1200
100
80
60
40
20
0 TOTA
L HE
AD –
MET
ERS
–29
00 R
PM –
50 H
ERTZ
CAPACITY – CUBIC METERS PER HOUR – 3500 RPM – 60 HERTZ
CAPACITY – CUBIC METERS PER HOUR – 1450 RPM – 50 HERTZ0 20 40 60 80 100
120
100
80
60
40
20
0
TOTA
L HE
AD –
FEET
–17
50 R
PM –
60 H
ERTZ
0
5
10
15
20
25
CAPACITY – U.S. GALLONS PER MINUTE – 1750 RPM – 60 HERTZ0 100 200 300 400 500 600
TOTA
L HE
AD –
MET
ERS
–14
50 R
PM –
50 H
ERTZ
250
PUMPING TEMPERATURE – °C200150100500-50
3500
3000
2500
2000
1500
1000
500
0500
500
400
300
200
100
0-100 0 100 200 300 400
PUMPING TEMPERATURE – °F
WOR
KING
PRE
SSUR
E –
kPa
WOR
KING
PRE
SSUR
E –
PSIG
240 260 280 300 320 340
1400 1600 1800
120 140 160 180 200 220 240 260
700 800 900 1000 1000 1200 1300 1400
RWA4166 & RWA4206 PUMPS
RWA2096
DEAN PUMP® RWAV SERIES
Vertical Inline Air Cooled Hot Water Pumps• Capacities to 360 GPM (82 m3/hr)• Heads to 320 feet (98 m)• Pumping Temperatures to 400°F (204°C)• Working Pressures to 450 PSIG (3,103 kPa)• Six Sizes
The RWAV Series offers the same design benefits as the RWASeries but in a vertical configuration. Pumps feature a shaftmounted fan to provide air flow over the cooling fins of thepump. This air-cooled design translates to NO EXTERNAL WATERCOOLING REQUIRED for the bearings and mechanical seal.Three sizes are available in ductile iron construction.
Working Pressure vs. Pumping Temperature
Head-Capacity Range Charts
PUMPING TEMPERATURE – °C
PUMPING TEMPERATURE – °F
Two Pole Motor
Four Pole Motor
CAPACITY – CUBIC METERS PER HOUR – 2900 RPM – 50 HERTZ
TOTA
L HE
AD –
FEET
–35
00 R
PM –
60 H
ERTZ
CAPACITY – U.S. GALLONS PER MINUTE – 3500 RPM – 60 HERTZ
TOTA
L HE
AD –
MET
ERS
–29
00 R
PM –
50 H
ERTZ
0 10 20 30 40 50 60 70
400360320280240200160120804000
50
100
150
200
250
300
350
0
10
20
30
40
50
60
70
RWAV
1X1
.5X8
RWAV 1X1.5X6 RWAV 1.5X3X6
RWAV 1.5X3X8.5
RWAV 2X3X8.5RWAV 1X3X8.5
CAPACITY – CUBIC METERS PER HOUR – 1450 RPM – 50 HERTZ
TOTA
L HE
AD –
FEET
–17
50 R
PM –
60 H
ERTZ
CAPACITY – U.S. GALLONS PER MINUTE – 1750 RPM – 60 HERTZ
TOTA
L HE
AD –
MET
ERS
–14
50 R
PM –
50 H
ERTZ
0 5 10 15 20 25 30 35
0 20 80 1006040 120 140 2000
20
30
40
50
60
70
80
90
0
2
4
6
8
10
12
16
14
18
10
160 180
RWAV 1X1.5X8
RWAV 1X1.5X6 RWAV 1.5X3X6
RWAV 2X3X8.5
RWAV
1.5X
3X8.5
RWAV
1X3X
8.5
WOR
KING
PRE
SSUR
E –
PSIG
WOR
KING
PRE
SSUR
E –
KPa
--73 -35 3 41 79 117 155 193 231 269 307
-100 0 100 200 300 400 7000
50
250
300
350
400
450
500
0
250
500
750
1000
1250
1500
1750
2000
2250
2500
2750
3000
3250
200
150
100
500 600
RWAV 4096 PUMPSRWAV 4166 PUMPS
345
© 2012 MET-PRO CORPORATION
DEAN PUMP® IS A REGISTERED TRADEMARK OF MET-PRO CORPORATION 09-5941 612
6040 Guion Road • Indianapolis, IN 46254P: 317.293.2930 • TOLL-FREE: 800.801.9265 • F: [email protected] • www.mp-gps.com
Met-Pro Corporation is a global provider of solutions and products for product recovery, pollution control and fluid handling applications. The Company’s products include filtration and purification equipment for air, water and harsh, corrosive applications; fluid handling equipment for water, corrosive, abrasive, and high temperature liquids; and proprietary water treatment chemicals. For more information, visit www.met-pro.com.
Met-Pro Global Pump Solutions, which combines the resources of the Company’s internationally recognized Dean Pump®, Fybroc® and Sethco® brands, is a leading niche-oriented global provider of solutions and products forthe pumping of corrosive, abrasive and high temperature liquids. Its broad range of high quality centrifugal pumps provide excellent performance for tough applications including pumping of acids, brines, caustics, bleaches, seawater, high temperature liquids and a wide variety of waste liquids for a broad range of applications includingthe chemical, petrochemical, metal finishing, wastewater treatment, desalination and aquarium/aquaculture markets.For more information, visit www.mp-gps.com
ABOUT MET-PRO
ABOUT MET-PRO GLOBAL PUMP SOLUTIONS