datasheet_STG-SPP Splitter VDSL_POTS_with Protection_07_405_06300_Ind0.pdf

8/11/2019 datasheet_STG-SPP Splitter VDSL_POTS_with Protection_07_405_06300_Ind0.pdf

1/4

Datasheet

3M

STG-SPP Splitter for VDSL over POTS

CO-Splitter for VDSL over POTS

Features

Connectivity

Separated termination field for DSLAM wires or jumpers Front facing IDC Open wire guide management

Splitters or Modules

Removable Single port splitter modules Bridging modules for g.SHDSL, Full unbundling and VoIP applications Different types of splitters Lifeline service : Voice circuit is maintained and

Data service is disconnected while removing the splitterTest functionalities

Primary protection included (POTS + LINE)

Test functionalities

Intrusive testing capabilities in all directions (DSLAM, LINE, POTS) by insertion of the 3 ways Test Plug instead at the splitter position Parallel Test plug for front side non intrusive testing

Benefits

Adapted in countries using Wire Wrap connection technique. No specific need for training.Adapted to all types of deployment No risk of mistake

OPEX improvement by single line customer management

Future-proof and support future xDSL services deployment

Line qualification and monitoring without changing the wires

3M STG-SPP Integrated Splitter Block

Latest generation 3M STG Integrated Splitter Block is matching all

type of DSLAM equipment deployment (DSLAM interconnection at the

CO, Line-sharing and unbundling, Remote DSLAM deployments in the

OSP). Product design integrates unique features to match TELCOs

expectations for a mass xDSL lines deployment with the better Service

Level.

Increasing Quality of Service

Splitters are fully protected inside the product to avoid any accidential

disconnection of the end-user. This is particularly important with the

emergence of higher added value services over DSL such as TriplePlayservices.

Optimizing the space in the Central Office

Very compact and modular by design, STG requires less space on the

MDF frame and is very adapted for remote application in cabinets or

shelters. 64 VDSL ports can be served from a 165 mm length block.

Improving OPEX

Using Single port splitter plugs, STG reduces the number of jumpering

and maintenance operations (Service change, ADSL, ADSL2+, a.SHDSL,

VDSL, lifeline service in case of disconnection from the Data service,

Intrusive testing in all directions).

Adaptation to TELCO Engineering procedures

STG splitter block is convenient for craftmen as a whole 10 pairs bundle

can be terminated on the same connection module. This is also better

matching existing information systems. Products does not require any

particular investment in connectivity tooling and training because 3M

IDC connectivity can be used.


2/4

Installation and Labeling Deployment Configurations

Mounting Vertical or Horizontal side of the MDF Mounting kit according to local frame designs

Identification, Labeling 1 Label for 20 ports modulesAdditional label holders are available for front- and side marking

Types of Deployment DSLAM Interconnection: 1 cable (DSLAM) + 2 jumpers (LINE, POTS) UNBUNDLING: 3 jumpers (DSLAM, LINE, POTS)

Dimensions Length (or height) 165 mm Width 146 mm Depth 82 mm (w/o splitter)

Connectivity IDC contacts form wires from 0.4 mm to 0.8 mm T-connection facility with different gauges wires

Specifications for the block

Splitter Modules Different types of Splitter modules are available

Ordering Information

IDC Connectivity with protection facility

3M STG-SPP Integrated Splitter Block, 64 ports, IDC, with Protection facility IA340535250 1

SPLITTER module

3M STG Splitter VDSL2 /12 POTS with Protection 242366CB 64

Ref.-No. PU


3/4

Specifications for the splitter module

General

Splitter Type CO-Splitter for VDSL over POTS

Maximum DC loop current 100mA

Maximum DC loop voltage 120V

max. DC loop resistance 50ohms

Type of high-pass DC-blocking 120nF

over-voltage susceptibility acc. ITU-T K.20 and K.45 with primary prot., basic test level

Signalling

Ringing frequency 25/50Hz

max. ringing voltage 100Vrms+78VDC

POTS

Impedance system complex 320ohm+(1050ohms par. 230nF)

max. Insertion loss 1kHz 1dB

max. Insertion loss distortion 200Hz4kHz +/-1dB

Return loss >14dB to 18dB at 300 to 500Hz;

>18dB at 500 to 2000Hz;

>18dB to 14dB at 2000 to 3400Hz

LCL >40dB at 15Hz...50Hz

>46dB at 50Hz...600Hz

>52dB at 600Hz...4kHz

Group delay distortion 47dB at 12MHz...17MHz

Dimensions

Splitter module 9.8mm x 22.2mm x 133.6mm


4/4

Important Notice

Notes

Please recycle.Rights reserved to make technical alternations.Copyright 2010, 3M Company, USARef.No. 07-405-06300 / 06.2010 Rev. 0

3M Telecommunications

Europe, Middle East & Africac/o 3M Deutschland GmbHCarl-Schurz-Strae 141453 Neuss GermanyTel.: ++49 (0)2131 / 14-5999Fax: ++49 (0)2131 / 14-5998Internet: www.3MTelecommunications.com

The details contained in this literature have been carefully prepared from information available to 3M at the time of its production. However, it is not

intended to be relied upon for purposes of product specification and you should contact your sales representative if specification details are required.

Because of the wide variety of p rocesses and conditions in which these p roducts may be used, the user should fi rst carry out tests to determine the

suitability of the products for the particular use intended. All questions of warranty and liability relating to 3M products are governed by the selling 3M

subsidiary's Terms of Sale subject where applicable to the prevailing law.

3M is a trademark of 3M company.

datasheet_STG-SPP Splitter VDSL_POTS_with Protection_07_405_06300_Ind0.pdf

Documents

Transcript of datasheet_STG-SPP Splitter VDSL_POTS_with Protection_07_405_06300_Ind0.pdf