Data sheet Float valves Types SV 4, SV and SV 6 · 2020. 12. 14. · SV 4, 5 and 6 Classified for...
Transcript of Data sheet Float valves Types SV 4, SV and SV 6 · 2020. 12. 14. · SV 4, 5 and 6 Classified for...
-
Data sheet
Float valves Types SV 4, SV 5 and SV 6
AI175286419654en-000507 | 1© Danfoss | DCS (ms) | 2019.07
SV 4-6 are for use on the low pressure side as modulating liquid level regulators in refrigeration, freezing and air conditioning systems with ammonia and other common types of refrigerants.
Features • Reliable function.• Stable regulation, even during momentary
load change.• Liquid injection into the float housing or
directly into the evaporator through external pipe connection.
• Orifice assembly and filter can be replaced without evacuating the float housing.
• Can be supplied without float housing for direct installation in the system (special order only).
Technical data RefrigerantsApplicable to HCFC, HFC and R717 (Ammonia).Use with flammable hydrocarbons cannot be recommended; please contact Danfoss.
P bandApprox. 35 mm
Max. working pressureMWP = 28 barMax. ∆pSV 4 = 23 barSV 5 = 21 barSV 6 = 19 bar
Media temperature–50 °C to 120 °C
Max. test pressureMTP = 32 bar
kv value and diameter for orificeSV 4: kv = 0.23 m3/h D = 3.0 mmSV 5: kv = 0.31 m3/h D = 3.5 mmSV 6: kv = 0.43 m3/h D = 4.0 mm
• Can be used as pilot float for PMLF if mounted with special orifice (diameter Ø2.5 mm).
• Classification: DNV, CRN, BV, EAC etc. To get an updated list of certification on the products please contact your local Danfoss Sales Company.
-
Data sheet | Float valves, types SV 4, SV 5 and SV 6
2 | AI175286419654en-000507 © Danfoss | DCS (ms) | 2019.07
Approvals Pressure Equipment Directive (PED)SV 4, 5 and 6 are approved in accordance with the European standard specified in the Pressure Equipment Directive and are CE marked.For further details / restrictions - see Installation Instruction
Identification
SV 4, 5 and 6
Classified for Fluid group I
Category II
Dimensioning examplefor SV
Subcooling∆tsub = tc − tl = 30 °C − 20 °C = 10 K
Pressure drop in SV∆p = pc − pe = 11.7 − 2.9 = 8.8 bar
Correction factor k for 10 K subcooling= 0.98
Corrected capacity145 × 0.98 = 142 kW
At te = −10°C and ∆p = 8 bar SV 5 yields 147 kW and can therefore be used.
RefrigerantR717 (NH3)
Evaporating capacityQe = 145 kW
Evaporating temperaturete = −10 °C (~ pe = 2.9 bar abs.)
Condensing temperaturetc = +30 °C (~ pc = 11.7 bar abs.)
Liquid temperature ahead of SVtl = +20 °C
Materials • Gaskets are non asbestos• Valve housing made of lowtemperature cast
iron, spherical (EN-GJS-400-18-LT)
• Float housing: ST 35.8 DIN 17175 W. no. 1.0305
-
Data sheet | Float valves, types SV 4, SV 5 and SV 6
AI175286419654en-000507 | 3© Danfoss | DCS (ms) | 2019.07
R22
Correction factorsWhen dimensioning, multiply the evaporating capacity by the correction factor k, dependent on the subcooling ∆tsub just ahead of the valve. The corrected capacity can then be found in the capacity table.
R717 (NH3)
The values in the capacity tables are based on a subcooling of 4 K just ahead of the SV valve.If the subcooling is more or less than 4 K, refer to the following correction factors.
Capacity
R717 (NH3)
R22
Type
Evaporatingtemperature
te °C
Capacity in kW at pressure drop across valve ∆p bar
0.8 1.2 1.6 2 4 8 12 16
Type
Evaporatingtemperature
te °C
Capacity in kW at pressure drop across valve ∆p bar
0.8 1.2 1.6 2 4 8 12 16
SV 4
+10 0−10−20−30−40−50
37394041424243
45474849505151
52545556575858
58596162636363
79818283848483
105107108109109108107
122124125125125124122
134136137137136135133
SV 5
+10 0−10−20−30−40−50
51535456575858
62646667686969
71737576787878
78818384858686
107110112113114114113
143145147148148147146
166168170170170168167
183185186186185184182
SV 6
+10 0−10−20−30−40−50
68717375767778
83868890929393
9598
101103104105105
105108111113115115115
144147150152153153152
191195197198198197196
222226227228227226223
245248250250248246243
SV 4
+10 0−10−20−30−40−50
8.58.99.39.79.9
10.110.3
10.310.711.211.611.812.112.1
11.712.212.713.113.413.613.6
12.913.514.014.414.614.814.8
17.217.818.318.718.918.918.8
21.822.422.823.123.122.922.6
24.124.625.025.125.024.724.2
25.125.725.925.925.725.324.8
SV 5
+10 0−10−20−30−40−50
11.612.112.713.113.513.814.0
14.014.615.215.716.116.416.5
15.916.717.317.818.218.418.5
17.618.419.019.619.920.120.2
23.424.324.925.425.725.725.6
29.630.531.131.431.431.230.7
32.733.534.034.134.033.633.0
34.234.935.335.335.034.533.7
SV 6
+10 0−10−20−30−40−50
15.516.317.017.618.118.518.7
18.719.620.421.121.622.022.2
21.322.323.223.924.424.724.8
23.624.625.526.226.727.027.0
31.432.633.534.134.534.534.3
39.740.941.742.142.141.841.2
43.945.045.645.845.645.044.2
45.846.847.347.347.046.245.2
∆t K 2 4 10 15 20 25 30 35 40 45 50
k 1.01 1.00 0.98 0.96 0.94 0.92 0.91 0.89 0.87 0.86 0.85
∆t K 2 4 10 15 20 25 30 35 40 45 50
k 1.01 1.00 0.96 0.93 0.90 0.87 0.85 0.83 0.80 0.78 0.77
-
Data sheet | Float valves, types SV 4, SV 5 and SV 6
4 | AI175286419654en-000507 © Danfoss | DCS (ms) | 2019.07
ConstructionFunction
No. Part Material DIN / EN
1 Bottom flange for float valve Steel P275NL1EN10028-3
2 Tube for valve body Steel TTST35NDIN17173
3 Connection for float house Steel TTST35NDIN17173
4 Top cover for float valve Steel P275NL1EN10028-3
5 Valve housing Low temperature, cast iron(spherical)
EN-GJS-400-18-LTEN1563
6 Spindle Stainless steel
7 Spring Steel
8 Sealing ring Nylon (PA 6)
9 O-ring Cloroprene (Neoprene)
10 Distance ring Nylon (PA 6)
11 Packing ring Nylon (PA 6)
12 Packing box Steel
13 Cap Steel
14 Float Stainless steel
15 Adjusting ring Steel
16 Pin Steel
17 Fork for spindle Steel
18 Screw Steel
19 Locking ring Steel
20 Pin Steel
-
Data sheet | Float valves, types SV 4, SV 5 and SV 6
AI175286419654en-000507 | 5© Danfoss | DCS (ms) | 2019.07
ConstructionFunction(cont.)
No. Part Material DIN / EN
21 Pin Steel
22 Cover with guide Steel
23 Screw Steel
24 Plug Steel
25 Gasket Non asbestos
26 Gasket Aluminium
27 Valve cone (guide) with pin Steel / Nylon (PA6)
28 Valve cone Teflon (PTFE)
29 O-ring Cloroprene (Neoprene)
30 Nozzle Teflon (PTFE)
31 Gasket Non asbestos
32 Filter Steel / Stainless steel
33 Spring Steel
34 Cover for filter Steel
35 Gasket Aluminium
36 Nipple Steel
37 Union nut Steel
38 Gasket Aluminium
39 Welding nipple Steel
40 Locking ring Steel
41 Ring Nylon (PA6)
42 Pin Steel
43 Screw Stainless steel A2-70
44 Screw Stainless steel A2-70
45 Washer Steel
46 Screw Stainless steel A2-70
-
Data sheet | Float valves, types SV 4, SV 5 and SV 6
6 | AI175286419654en-000507 © Danfoss | DCS (ms) | 2019.07
SV 4-6 float valves are for low pressure operation only. They are used for flooded evaporators, where only slight variations in the liquid level can be accepted.When the liquid level decreases, the float moves downwards. This opens the orifice (pos. 7) and the amount of liquid injected is increased.
The liquid inlet line should be dimensioned in such a way that acceptable liquid velocities and pressure drops are obtained.This is particularly important when the liquid is only slightly subcooled, since valve capacity is reduced considerably if flashgas occurs in the liquid ahead of the orifice.
The flashgas quantity which occurs on expansion is removed through the balance pipe. On refrigeration plant using fluorinated refrigerants, slight subcooling and a large pressure drop can result in a flashgas quantity of approx. 50% of the injected liquid quantity.
Therefore the pressure drop in this balance pipe must be kept at a minimum, otherwise there isa risk that:
the liquid level in the evaporator will vary to an unacceptable degree as a function of evaporator loadthe absolute difference between the liquid level of the evaporator and the SV valve
If too large amounts of flash gas are created it is recommended to use the external injection connection or let the liquid expand directly into the surge drum. See application drawings 3 and 4.
See instruction for SV 4 - 6 for:• Cleaning of strainer• Change of orifice• Change of valve plate
ConstructionFunction(cont.)
-
Data sheet | Float valves, types SV 4, SV 5 and SV 6
AI175286419654en-000507 | 7© Danfoss | DCS (ms) | 2019.07
Application The liquid expands into the float housing The liquid expands into the float housing
4 pcs. M6 screws (pos. 23) are removed, and pos. 24 remains blanked off. This leaves four holes through which liquid expands directly. Note: If the capacity is too high, only remove two or three screws.Pos. 23 and 24, see Construction & Function.
Direct liquid injection into the float housing 4 pcs. M6 screws (pos. 23) are removed, and pos. 24 remains blanked off. This leaves four holes through which liquid expands directly. Note: If the capacity is too high, only remove two or three screws.Pos. 23 and 24, see Construction & Function.
The liquid expands into the evaporator The liquid expands directly into the surge drum
Used in large evaporators with long pipe lines.– pos. 24 is removed and weld connection is
mounted– pos. 23 remains screwed
Pos. 23 and 24, see Construction & Function.
4 pcs. M6 screws (pos. 23) are removed, and pos. 24 remains blanked off. This leaves four holes through which liquid expands directly. Note: If the capacity is too high, only remove two or three screws.Pos. 23 and 24, see Construction & Function.
1) 2)
3) 4)
-
Data sheet | Float valves, types SV 4, SV 5 and SV 6
8 | AI175286419654en-000507 © Danfoss | DCS (ms) | 2019.07
Dimensions and weight
Weight: 19.6 kg
Weight: 9.7 kg
Weight: 3.1 kg
-
Data sheet | Float valves, types SV 4, SV 5 and SV 6
AI175286419654en-000507 | 9© Danfoss | DCS (ms) | 2019.07
Ordering
Spare parts and accessoriesSmaller orifices for the SV 4 - 6 are available as spare parts and can be mounted in the SV 4 - 6 if smaller capacities are required.
– Seal kit: 027B2070 – Other spare parts: See spare parts
catalogue
Special orifice code no. and rated capacities for SV 4 - 6
Orifice diameter kv
Capacities at –10°C evaporating temperature at pressuredrop across valve ∆P bar
Code no. 1)R717 R22
4 7 10 4 7 10
∅ 1.0 mm 0.026 9 12 13.5 1.6 2.2 2.4 027B2080∅ 1.5 mm 0.06 21 27 29 3.8 4.9 5.2 027B2081∅ 2.0 mm 0.10 35 46 50 6.3 8.3 9 027B2082∅ 2.5 mm 0.16 56 70 81 10 13 15 027B2083∅ 2.8 mm 0.20 70 87.5 101 12 16 18 027B2084
1) The code no. includes orifice and all necessary gaskets
Note: The SV 4 - 6 mounted with special orifice diameter ∅2.5 mm is recommended as pilot float valve for the servo-operated level regulators type PMFL for higher capacities.
RegulatorThe code nos. stated apply to float valves types SV 4, 5 and 6 with two 1" weld connections for balance tubes and two ½" weld joints for liquid and evaporator connections respectively.
Valve typeOrifice
diameterCode no. Code no.without housing 2)
Rated capacity in kW1)
R717 R22 R134a R404A
SV 4 ∅ 3.0 mm 027B2024 027B2014 102 21.0 16.4 15.4
SV 5 ∅ 3.5 mm 027B2025 027B2015 138 28.6 22.3 21.0
SV 6 ∅ 4.0 mm 027B2026 027B2016 186 38.3 29.9 28.1
1) The rated capacity refers to the valve capacity at evaporating temperature tc = + 5 °C, condensing temp. tc = + 32 °C and liquid temperature tl = + 28 °C.
2) Flange for mounting without housing Code no. 027B2027.
-
AI175286419654en-000507 | 10© Danfoss | DCS (ms) | 2019.07