Data Acquisition Boards - Esis€¦ · Operating system used 2. User programming expertise 3....

9Data Acquisition Boards

Data Acquisition and Control Tutorial & Software 9-2ActiveDAQ Pro Introduction 9-4Selection Guide 9-8Mutlifunction CardsPCI-1710/LPCI-1710HG/HGL

100 kS/s, 12-bit, 16-ch PCI Multifunction Card100 kS/s, 12-bit, 16-ch PCI Multifunction Card with High Gain 9-14

PCI-1711/L Entry-level 100 kS/s, 12-bit, 16-ch PCI Multifunction Card 9-16PCI-1712/L 1 MS/s, 12-bit, 16-ch PCI Multifunction Card 9-18PCI-1716/L 250 kS/s, 16-bit, 16-ch PCI Multifunction Card 9-20PCI-1718HDU 100 kS/s, 12-bit, 16-ch Universal PCI Multifunction Card 9-22PCI-1741UPCI-1742U

200 kS/s, 16-bit, 16-ch Universal PCI Multifunction Card1 MS/s, 16-bit, 16-ch Universal PCI Multifunction Card 9-24

PCL-711B 40 kS/s, 12-bit, 8-ch ISA Multifunction Card 9-26PCL-812PG 30 kS/s, 12-bit, 16-ch ISA Multifunction Card 9-27PCL-818HD/HGPCL-818L

100 kS/s, 12-bit, 16-ch ISA Multifunction Card40 kS/s, 12-bit, 16-ch ISA Multifunction Card 9-28

Analog I/O CardsPCI-1713 100 kS/s, 12-bit, 32-ch Isolated Analog Input PCI Card 9-30PCI-1715U 500 kS/s, 12-bit, 32-ch Isolated Analog Input Universal PCI Card 9-31PCI-1714UPCI-1714UL

30 MS/s, 12-bit, Simultaneous 4-ch Analog Input Universal PCI Card10 MS/s, 12-bit, Simultaneous 4-ch Analog Input Universal PCI Card

9-329-32

PCI-1747U 250 kS/s, 16-bit, 64-ch Anglog Input Universal PCI Card 9-33PCL-813B 25 kS/s, 12-bit, 32-ch Isolated Analog Input ISA Card 9-34PCI-1720U 12-bit, 4-ch Isolated Analog Output Universal PCI Card 9-35PCI-1721 12-bit, 4-ch Analog Output PCI Card with 16-ch Digital I/O 9-36PCI-1723 16-bit, 8-ch Analog Output PCI Card with 16-ch Digital I/O 9-37PCI-1724U 14-bit, 32-ch Isolated Analog Output Universal PCI Card 9-38PCL-727 12-bit, 12-ch Analog Output ISA Card with 32-ch Digital I/O 9-39PCL-726PCL-728

12-bit, 6-ch Analog Output ISA Card with 32-ch Digital I/O12-bit, 2-ch Isolated Analog Output ISA Card 9-40

Digital I/O & Counter CardsPCI-1737U 24-ch Digital I/O Universal PCI Card 9-41PCI-1739U 48-ch Digital I/O Universal PCI Card 9-42PCI-1751 48-ch Digital I/O and 2-ch Counter PCI Card 9-43PCI-1753 96-ch Digital I/O PCI Card 9-44PCI-1757UP 24-ch Digital I/O Low Profile Universal PCI Card 9-45PCL-720+ 64-ch Digital I/O and Counter ISA Card 9-46PCL-722 144-ch Digital I/O ISA Card 9-47PCL-724 24-ch Digital I/O ISA Card 9-48PCL-731 48-ch Digital I/O ISA Card 9-49PCI-1730PCI-1733PCI-1734

32-ch Isolated Digital I/O PCI Card32-ch Isolated Digital Input PCI Card32-ch Isolated Digital Output PCI Card

9-50

PCI-1750 32-ch Isolated Digital I/O and 3-ch Counter PCI Card 9-51PCI-1752UPCI-1754PCI-1756

64-ch Isolated Digital Output Universal PCI Card64-ch Isolated Digital Input PCI Card64-ch Isolated Digital I/O PCI Card

9-52

PCI-1758UDIPCI-1758UDO

128-ch Isolated Digital Input Universal PCI Card128-ch Isolated Digital Output Universal PCI Card 9-53

PCI-1760U 8-ch Relay and 8-ch Isolated Digital Input Universal PCI Card with 10-ch Counter/Timer 9-54

PCI-1761 8-ch Relay and 8-ch Isolated Digital Input PCI Card 9-55PCI-1762 16-ch Relay and 16-ch Isolated Digital Input PCI Card 9-56PCL-725 8-ch Relay and 8-ch Isolated Digital Input ISA Card 9-57PCL-735 12-ch Relay ISA Card with 16-ch Digital I/O 9-58PCI-1780U 8-ch, 16-bit Counter/Timer Universal PCI Card 9-59PCL-836 6-ch, 16-bit Counter/Timer ISA Card 9-60PC/104 & PCI-104 DAQ CardsPCM-3813I (New)PCM-3718H/HG/HOPCM-3724

100 kS/s, 12-bit, 32-ch Isolated Analog Input PCI-104 Module100 kS/s, 12-bit, 16-ch PC/104 Multifunction Module48-ch Digital I/O PC/104 Module

9-61

PCM-3725PCM-3730PCM-3780

8-ch Relay and Isolated Digital Input PC/104 Module16-ch Isolated Digital I/O PC/104 Module2-ch Counter/Timer with 24-ch Digital I/O PC/104 Module

9-62

PCM-3730I (New)PCM-3753I (New)PCM-3761I (New)

32-ch Isolated Digital I/O PCI-104 Module96-ch Digital I/O PCI-104 Module8-ch Relay and 8-ch Isolated Digital Input PCI-104 Module

9-63

PCI-bus GPIB CardPCI-1671UP IEEE-488.2 Interface Low Profile Universal PCI Card 9-64

Data Acquisition Boards9-2

Data Acquisition and Control Tutorial & Software

The layout of a typical PC-based data acquisition system

PC-based Data Acquisition (DAQ) System OverviewBecause industrial PC I/O interface products have become increasingly reliable, accurate, and affordable in the last few years, PC-based data acquisition and control systems are nowadays widely used in industrial and laboratory applications such as monitoring, control, data acquisition and automated testing.

It requires know-how of electrical and computer engineering to select and build a data acquisition (DAQ) and control system that actually does what you want. This tutorial gives a brief introduction to what data acquisition and control systems do and how to configure them. Here, we cover:

Transducers and ActuatorsSignal Conditioning Data Acquisition and Control HardwareGetting Started

Transducers and ActuatorsA transducer converts temperature, pressure, level, length, position, etc. into voltage, current, frequency, pulses or other signals.

Thermocouples, thermistors and resistance temperature detectors (RTDs) are common transducers for temperature measurements. Other types of transducers include flow sensors, pressure sensors, strain gauges, load cells and LVDTs, which measure flow rate, pressure variances, force or displacement.

An actuator is a device that activates process control equipment by using pneumatic, hydraulic or electrical power. For example, a valve actuator can open and close a valve to control fluid rates.

Signal ConditioningSignal conditioning circuits improve the quality of signals generated by transducers before they are converted into digital signals by the PC's data-acquisition hardware. Examples of signal conditioning are signal scaling, amplification, linearization, cold-junction compensation, filtering, attenuation, excitation, common-mode rejection, and so on.

One of the most common signal conditioning functions is amplification. For maximum resolution, the voltage range of the input signals should be approximately equal to the maximum input range of the A/D converter. Amplification expands the range of the transducer signals so that they match the input range of the A/D converter. For example, a x10 amplifier maps transducer signals that range from 0 to 1 V into the range 0 to 10 V before they go into the A/D converter.

Using digital I/O and SSRs to open and close a valve

www.advantech.com/productsOnline Download 9-3

8

544

10USB DAQ

9Signal Conditioning

8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor

3Industrial Panel PC

2Touch Panel PC

1Automation Software

11Motion Control I/O12

Fanless Box PC

PC-based Controller13

PAC14

RS-485 I/O15

Ethernet I/O16

Building Automation17

Video Surveillance18

Data Acquisition & Control HardwareData acquisition and control hardware generally performs one or more of the following functions: analog input, analog output, digital input, digital output and counter/timer functions. This section will discuss each function and list some considerations that are important when you select a data acquisition and control system.

Analog Inputs (A/D)Analog to digital (A/D) conversion changes analog voltage or current levels into digital information. The conversion is necessary to enable a computer to process or store the signals.

DAQ Tutorial & Software

The most significant criteria when selecting A/D hardware are:

1. Number of input channels

2. Single-ended or differential input signals

3. Sampling rate (in samples per second)

4. Resolution (usually measured in bits of resolution)

5. Input range (specified in full-scale volts)

6. Noise and nonlinearity

Analog Outputs (D/A)The opposite of analog to digital conversion is digital to analog (D/A) conversion. This operation converts digital information into analog voltage or current. D/A devices allow a computer to control real-world events.

Getting StartedAdvantech: The Source For What You NeedAdvantech manufactures data acquisition hardware and software for measurement, monitoring and applications control. The following guide is provided to help you choose components for your data acquisition system.

Step 1: Know Your Fundamental GoalDecide whether your DAQ system will be used primarily for measurement, monitoring, control, or analysis. Know the data requirements of your process, and know the number of data collection points in your system. Know the required data collection speed, the sampling rate, the type of measurement, the voltage or current being produced, the desired accuracy and the output resolution at each data collection point. Finally, know the timing of events in your system, and any special environmental conditions that exist.

Step 2: Hardware SelectionSelect the hardware required to achieve your fundamental goal. Advantech provides plug-in boards for Analog-to-Digital, Digital-to-Analog, Digital I/O needs. Both ISA and PCI bus products are available. Your hardware selection should be based on five major criteria:

1. Number and types of channels

2. Differential or single-ended inputs

3. Resolution

4. Speed

5. Software compatibility with hardware

Step 3: Accessory SelectionMost applications require additional accessories which are available as separate items. These include:

1. Expansion peripherals to add channels to your system

2. Cables, signal conditioners and external boxes such as screw terminals or BNC accessories

Step 4: Software SelectionMore than any other single factor, software will determine your system start-up time, as well as its effectiveness, suitability for your application, and ease of modification.

Three major criteria should determine the choice of software:

1. Operating system used

2. User programming expertise

3. Software compatibility with hardware

Analog output signals may directly control process equipment. The process can give feedback in the form of analog input signals. This is referred to as a closed loop control system with PID control. Analog outputs can also be used to generate waveforms. In this case, the device behaves as a function generator.

Digital Inputs and OutputsDigital input/output functions are useful in applications such as contact closure and switch status monitoring, industrial On/Off control and digital communications.

Counter/TimerA counter/timer can be used for event counting, flowmeter monitoring, frequency counting, pulse width measurement, time period measurement, and so on.


ActiveDAQ Pro IntroductionWhat is ActiveDAQ Pro ?ActiveDAQ Pro is a collection of ActiveX controls for performing I/O operations within any compatible ActiveX control container, such as Visual Basic, Delphi, etc. You can easily perform the I/O operations through properties, events and methods. With ActiveDAQ Pro, you can perform versatile I/O operations to control your Advantech devices.

The ActiveDAQ Pro package contains the following components:

Advantech ActiveDAQ Pro Device Control: Enumerate all Advantech devices, direct I/O operation. Advantech ActiveDAQ Pro AI Control: Retrieve data from Advantech AI device. Advantech ActiveDAQ Pro AO Control: Export data to Advantech AO device. Advantech ActiveDAQ Pro Digital I/O Control: Digital I/O operation. Advantech ActiveDAQ Pro Thermo Control: Retrieve temperature by thermocouple measurement. Advantech ActiveDAQ Pro Counter Control: Counter input signal. Advantech ActiveDAQ Pro Pulse Control: Pulse signal output.

You can use these ActiveX controls in any development tool that supports them, including Microsoft Visual C++, Microsoft Visual Basic, Borland C++ Builder, Borland Delphi and Microsoft Visual Studio .NET.

What's New in ActiveDAQ Pro ?In the latest version of the ActiveDAQ series: ActiveDAQ Pro, efforts have been made to improve on the technical aspects and to provide a clear-cut mode of operation, as explained in the following summary:

Graphic User Interface Control ComponentsAdvantech ActiveDAQ Pro GUI control collection consists of abundant of graphic user interface (GUI) control components, which enable users to conveniently and quickly build graph display modules for data acquisition so as to supervise the changing status of the object. ActiveDAQ Pro GUI control collection also helps users easily develop prototype vision applications in an interactive environment without programming. These control components include:

Button Control: It offers various display styles (2D and 3D) and is a Boolean control that displays an on or off state (True or False). Graph Control: This control provides abundant graph display functions, which enable the user to display data of various sources simultaneously.

Intensity Control: It offers two-dimensional display and simple interpolation for scattered 3D data points so that the user can conveniently check the intensity variation trend of scattered 3D data points.

Knob Control: It is a circular data controlling control that provides various graph styles and can be used to display one or more values on the same interface.

LED Control: This control provides data display and editing functions with the seven-segment nixie tube mode. NumEditor Control: This control provides the user with the functions of data displaying and editing. After the Formatstring has been chosen or defined by the user, the values of the control will be adjusted automatically according to the FormatString and displayed in the text edit box. Slider Control: It is a linear data controlling control that provides various graph styles. A Slider control can be used to set or display one or more values.


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Supports All Advantech DAQ Devices with High Speed FunctionsActiveDAQ Pro now fully supports all Advantech DAQ cards and functions with complete high speed data acquisition, including AI (analog input), AO (analog output), DI/O (digital input/output) and counter cards. These high speed functions are preformed by interrupt and DMA data transfer.

Easy-to-use Property Sheet Interface for Configuring ControlsThe property page will offer selections which will give easy access to all settings and eliminate unnecessary programming. Programming will only be required in specialized situations.

Independent Operation of ControlsActiveDAQ Pro offers total independent control operation, needing no support from other existing controls.

Uses Known Physical PropertiesPhysical properties like voltage, current and frequency can now be directly applied by the user and will automatically be reassigned to the data needed by GainCode and sampling rate. Making these changes has ensured that ActiveDAQ Pro has become much more user friendly.

Straightforward User InterfaceThe new version has become less-hardware dependent and it has relied more on intuition during the user interface. During the redesigned process, the target was to decrease the development difficulties. It has become easier for both entry level and advanced level users to manage.

Uses Optional Lists Instead of Direct InputNow lists are provided with values which remain limited over various processes. This option is much more convenient to input and will eliminate a large portion of the direct data input.

Default Settings for Immediate ExecutionProper default settings have now been added to all methods and properties. That means quicker execution for the user, which will offer a prompt response.

Properties and Parameters are Chosen AutomaticallyWhen the user opts for some specific methods in ActiveDAQ Pro it can result automatically in appropriate properties and parameters. For example, ActiveDAQ Pro control can automatically determine an appropriate data transferring method to perform the data acquisition. (Software, interrupt and DMA transfer)

Parameter Check-up and CorrectionEach input parameter has to be within a certain range. As a result it has to have check-up to ensure legitimacy. In most cases the user will be notified and in others there will be an automatic correction.

Better Defined Error Messages and Diagnostic GuideActiveDAQ Pro offers clear error messages description and diagnostic guides for all return errors.

Supports All Widely Known Development PlatformsActiveDAQ Pro support Microsoft Windows 2000 and Windows XP operation system.

As with the previous version, ActiveDAQ 1.6x, it continues to support all widely known development platforms based on ActiveX technolygy. These platforms include Microsoft Visual Basic, Visual C++, Visual Basic.Net, Visual C#, Borland C++ Builder and Delphi.

System Requirements PC with at least a 266 MHz or higher microprocessorMicrosoft Windows 2000/ XP/ VistaVGA compatible graphics card, supporting at least 256 colorsMinimum 64 MB of RAM74 MB of free local hard disk spaceOne CD-ROM driver

Ordering InformationPCLS-ADPSTD ActiveX Control-based Software for DAQ

ActiveDAQ Pro Introduction


GlossaryAccuracyAccuracy is the deviation of a measurement from a known standard. Accuracy is normally specified in percent.

ADC - Analog-to-Digital ConverterADC is used to convert DC voltage from transducers into digital words (data). The voltage representing a temperature, pressure, flow, pH, or speed and must converted to a digital word before it can be passed to an intelligent device like a computer.

AmplifierAmplifiers are used to boost the analog level (voltage) of the signal.

AO - Analog OutputThe D/A converter performs the opposite function of an A/D converter. It interprets commands from the computer and outputs the proper DC voltage or current. The output stays at this output level until the computer tells the D/A converter to output a new value.

Auto CalibrationThe built-in auto-calibration circuitry corrects gain and offset errors in analog input and analog output channels thereby eliminating the need for external equipment and user adjustments.

Automatic Channel/Gain/SD*/BU* ScanningAdvantech’s DAQ cards with this function feature an automatic channel/gain/SD/BU scanning circuit. This circuit controls multiplexer switching during sampling in a way that is more efficient than software implementation. Onboard SRAM stores different gain, SD and BU values for each channel. This combination lets users perform multi-channel high-speed sampling with different gain, SD and BU values for each channel.

*Note: SD: Single-Ended/Differential; BU: Bipolar/Unipolar

BoardID SwitchBoardID DIP switch helps defines each card’s unique identity when multiple identical PCI cards have been installed in the same computer. The BoardID switch is very useful when you build your system with multiple identical PCI cards. With the correct BoardID switch settings, you can easily identify and access each card during hardware configuration and software programming.

C/T - Counter/TimerThe counter card can be used to sense the presence or absence of a voltage, much like digital input card. The counter is used to count the number of electronic pulses (totalize), the duration of the pulse (pulse width), or the rate of pulses (frequency) coming out of an external device.

Channel-freezeThe channel-freeze function can be enabled either in dry contact or wet contact mode (selected by the onboard jumper). When the channel-freeze function is enabled, the last status of each digital output channel will be safely kept for emergency use. Moreover, you can enable this function through software as it is useful in software simulation and testing program.

Common Mode NoiseCommon mode noise most often results when the ground potential between the measuring instrument and the device being measured are different. The difference in grounds results in a ground loop, a current flowing through ground and the low lead. Once this current appears in the low lead wire it will cause a voltage because the wire has some resistance. The longer the lead, the more lead resistance and greater the voltage error.

TIP : To reduce common mode noise, use a guarded voltmeter. Tie the guard to the low side of the device being measured. This will shunt any ground loop currents away from the high and low measurement wires.

DI - Digital InputA digital input card is used to determine whether an external device is on or off by sensing the presence or absence of a voltage. The DI can only report ON/OFF status and not the value of the voltage on each channel (sometimes called a bit). The bit is considered to be ON if the voltage exceeds a certain value.

Digital cards usually feature 8, 16, or 32 channels. They can monitor a number of devices at the same time. For example, a digital card can be attached to a single operator panel to sense the position of switches on that panel.

Digital FilterThe digital filter function is used to eliminate glitches on input data and reduce the number of changes to examine and process. The filter blocks pulses that are shorter than the specified timing interval and passes pulses that are twice as long as the specified interval. Intermediate-length pulses that are longer than half of the interval, but less than the interval, may or may not pass the filter depending on your settings.

DMA - Direct Memory AccessA method of transferring data from or to memory at a high rate without involving the CPU. DMA is the hardware/software technique that allows the highest speed transfer of data, to or from random memory (RAM) . Given the potentially more expensive hardware, DMA can provide the means to read or write data at precise times without restricting the microprocessor' tasks. For example, one system under DMA control can read or write any combination of analog, digital or counter/timer data to or from RAM at rates up to 360KB/second. This is accomplished without taking time from the other tasks of the microprocessor. The amount of time required to respond to a DMA request is much smaller than the one required to service an interrupt. This makes the goal of foreground/background operation, at high speed, possible.

DO - Digital OutputThe digital output card interprets a command from the computer and outputs a high or low voltage on each of its channels (bits). It is commonly used to turn on/off small lights or to send digital words to machinery.

FSR - Full Scale RangeFSR stands for the difference between the largest positive and negative voltages which a AI channel can measure or a AO channel can output.

Gain - Magnitude RatioFor a linear system or element, the ratio of the magnitude (amplitude) of a steady-state sinusoidal output relative to the causal input; the length of a phasor form the origin to a point of the transfer locus in a complex plane.

GPIB - General Purpose Interface/Instrument BusA standard for IEEE-488 communication interface.

Interrupt Data TransferInterrupts provide a mean of tightly controlling the timing of events, while allowing the processing of more than one task. Multitasking systems are also known as “foreground/background” systems. One way of putting data acquisition in the background is to relegate it to an interrupt routine. The clock or external timing signal, rather than being polled continuously, is used to generate an interrupt to the computer. Whenever the interrupt occurs, the computer suspends current activity, and executes an “interrupt service routine”. The interrupt service routine in this case might be a short program which acquires one frame of data, and stores it in memory. The computer can perform other operations in the foreground while collecting data in the background. Whenever a clock tick or external interrupt occurs, the computer will automatically stop the foreground processing, acquire the data, and then resume where it left off.

The reaction speed of the interrupt system is much higher than that of a polling loop. Speed, for a PC, is about 10 kHz ~ 30 kHz in the interrupt mode.


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Isolation ProtectionIsolation circuits are used to protect sensitive measurement circuitry from interference currents or voltages. These circuits are useful when the external voltage (from a transducer) is separeted from the measurement hardware.

Keeping The Output Values After System ResetWhen the system is hot reset (power is not shut off), the Advantech’s DAQ cards with this function can either retain the last digital (or analog) output values, or return to its default configuration, depending on jumper setting. This practical function eliminates danger caused by misoperation during unexpected system reset.

LSB - Least Significant Bit

Onboard FIFO MemoryFIFO is the abbreviation of “First-In, First-Out”. It functions as a “buffer” memory, which plays an important role in the data acquisition device. You can either enable or disable the interrupt request of the FIFO buffer. While the interrupt request for FIFO is enabled, you can further specify whether the interrupt request will be sent whenever one sampling takes place or when the FIFO buffer is half saturated. Advantech’s data acquisition cards with onboard FIFO memory enables a continuous high-speed data transfer with more predictable performance on Windows systems.

Onboard Programmable CounterAdvantech’s multifunction cards provide a programmable counter to generate a pacer trigger for the A/D conversion. The counter chip is an 82C54 or equivalent, which includes three 16-bit counters on a 10 MHz clock. One counter is used as an event counter for counting events coming from the input channels. The other two are cascaded together to make a 32-bit timer for a pacer trigger.

Optical IsolatorsOptical isolators are used with digital circuitry to shield high voltage signals from affecting digital circuitry.

PCI-Bus Mastering Data TransferAdvantech’s high-speed DA & C cards support PCI-Bus mastering DMA for high-speed data transfer and gap-free analog input and analog output. By setting aside a block of memory in the PC, the DA&C cards performs bus-mastering data transfers without CPU intervention, setting the CPU free to perform other more urgent tasks such as data analysis and graphic manipulation. The function allows users to run all I/O functions simultaneously at full speed without losing data.

Plug & Play Function Advantech DAQ cards fully comply with the PCI spectication Rev 2.2 and thus are Plug & Play devices. During card installation, it is virtually unnecessary to set any jumpers or DIP switches. Instead, all bus-related configurations such as base I/O address and interrupts are conveniently taken care of by the Plug & Play function.

PollingPolling is the simplest method for detecting a unique condition and then taking action. This involves a software loop that contains all the required measurement, analysis, decision-making algorithms and planned actions. The data acquisition program periodically tests the system’s clock or external trigger input to sense a transition. Whenever a transition occurs, the program then samples each of the inputs and stores their values in a “frame”. A frame is simply a list that contains the values representing the specified inputs at a given time. The frames can be stored in RAM, disk or other types of memory. Each time the program senses a clock “tick”, the inputs are scanned and converted, and a new frame is added to memory. In this mode, generic computers can support an acquisition rate of about 10 kHz.

In addition, the PC is continuously busy when the polling loop is under operation, and hence no other tasks can be serviced. When an application cannot tolerate these characteristics, interrupt techniques may be needed.

Programmable Power-Up StatesWith this function, all output lines are user-configurable for logic high or logic low when the system is powering up. User-configurable power-up states are useful for ensuring that the data acquisition card powers up in a known state. Power-up states are programmed in the EEPROM through the driver. The default settings are all set to 0.

PWM - Pulse Width ModulationPulse width modulation (PWM) technology is widely used for industrial applications such as measurement, motor control, power control and so on. It offers a simple way for digital control logic to create an analog equivalence. By using Advantech’s high-resolution counter cards, the duty cycle of a square wave could be modulated to encode some specific analog signal levels so they can be used to control many electronic devices.

Resolution Resolution is the smallest change that a measurement instrument can sense. Resolution is normally specified in bits.

S.E. Input - Single Ended InputA single-ended configuration is the best when you need analog measurements against respect to a common external ground. This configuration is also appropriate when there is no practical way to bring both a signal ground and an analog ground (AGND) back to the system‘s input terminals.

ShieldingAn extra layer of conductive material surrounding a wire to prevent external electrical signals from interfering with the signal on the wire.

SPDT Relay - Single-Pole Dual-Throw Relay

SPST Relay - Single-Pole Single-Throw Relay

TTL - Transistor Transistor Logic

Watchdog TimerThe watchdog timer is a software-configurable feature used to set critical outputs to safe states in the event of a software failure. It will activate if there is a loss of communication between the application and the data acquisition card. If the card does not receive a watchdog clear software command within the interval time specified for the watchdog timer, the outputs go to a user-defined safe state and remain in that state until the watchdog timer is disabled and new values are written by the software.

After the watchdog timer expires, the card ignores any writes until the watchdog timer is disabled. Users can set the watchdog timer timeout period through WDT register to specify the amount of time that must elapse before the watchdog timer expires. The counter on the watchdog timer is configurable up to (232-1) x 100 ns (approximately seven minutes) before it expires.

Glossary


Category Multifunction Multifunction AI

Bus PCI PCI ISA PC/104 PCI

Model PCI-1710/L PCI-1710HG/L PCI-1711/L PCI-1712/L PCI-1716/L PCI-1718HDU PCI-1741U PCI-1742U PCL-711B PCL-812PG PCL-818L PCL-818HD PCL-818HG PCM-3718H PCM-3718HG PCM-3718HO PCI-1713 PCI-1714U PCI-1714UL

Anal

og In

put

General Spec.

Resolution 12 bits 12 bits 12 bits 12 bits 16 bits 12 bits 16 bits 16 bits 12 bits 12 bits 12 bits 12 bits 12 bits 12 bits 12 bits 12 bits 12 bits 12 bits 12 bits

Channels 16 SE/8 Diff. 16 SE/8 Diff. 16 SE 16 SE/8 Diff. 16 SE/8 Diff. 16 SE/8 Diff. 16 SE/8 Diff. 16 SE/8 Diff. 8 SE 16 SE 16 SE/8 Diff 16 SE/8 Diff 16 SE/8 Diff 16 SE/8 Diff. 16 SE/8 Diff. 16 SE/8 Diff. 32 SE/16 Diff. 4 SE 4 SE

Onboard FIFO 4,096 samples 4,096 samples 1,024 samples 1,024 samples 1,024 samples 1,024 samples 1,024 samples 1,024 samples - - - 1,024 samples 1,024 samples - - 1,024 samples 4,096 samples 32,768 samples 8,192 samples

Sampling Rate 100 kS/s 100 kS/s 100 kS/s 1 MS/s 250 kS/s 100 kS/s 200 kS/s 1 MS/s 40 kS/s 30 kS/s 40 kS/s 100 kS/s 100 kS/s 100 kS/s 100 kS/s 100 kS/s* 100 kS/s 30 MS/s 10 MS/s

Auto Channel Scanning

- -

Input Ranges

Unipolar Inputs (V)0 ~ 10, 0 ~ 5,

0 ~ 2.5, 0 ~ 1.25

0 ~ 10, 0 ~ 1, 0 ~ 0.1,

0 ~ 0.01-

0 ~ 10, 0 ~ 5, 0 ~ 2.5, 0 ~ 1.25

0 ~ 10, 0 ~ 5, 0 ~ 2.5,

0 ~ 1.25

0 ~ 10, 0 ~ 5, 0 ~ 2.5, 0 ~ 1.25

0 ~ 10, 0 ~ 5,

0 ~ 2.5, 0 ~ 1.25*

0 ~ 10, 0 ~ 5 0 ~ 2.5,

0 ~ 0.125- - -

0 ~ 10, 0 ~ 5, 0 ~ 2.5, 0 ~ 1.25

0 ~ 10, 0 ~ 1, 0 ~ 0.1, 0 ~ 0.01

0 ~ 10, 0 ~ 5 0 ~ 2.5,

0 ~ 0.125

0 ~ 10, 0 ~ 1 0 ~ 0.1, 0 ~ 0.01

0 ~ 10, 0 ~ 5 0 ~ 2.5,

0 ~ 0.125

0 ~ 10, 0 ~ 5, 0 ~ 2.5, 0 ~ 1.25

- -

Bipolar Inputs (V) ±10, 5, 2.5, 1.25, 0.625

±10, 5, 1, 0.5, 0.1, 0.05, 0.01, 0.005

±10, 5, 2.5, 1.25, 0.625

±10, 5, 2.5, 1.25, 0.625

±10, 5, 2.5, 1.25, 0.625

±10, 5, 2.5, 1.25, 0.625

±10, 5, 2.5, 1.25, 0.625*

±10, 5, 2.5, 1.25

0.625

±5, 2.5, 1.25, 0.625, 0.3125

±10, 5, 2.5, 1.25, 0.625,

0.3125

±10, 5, 2.5, 1.25, 0.625

±10, 5, 2.5, 1.25, 0.625

±10, 5, 1, 0.5, 0.1, 0.05, 0.01,

0.005

±10, 5, 2.5, 1.25

0.625

±10, 5, 1, 0.5, 0.1,

0.05, 0.01, 0.005

±10, 5, 2.5, 1.25 0.625

±10, 5, 2.5, 1.25, 0.625

±5, 2.5, 1, 0.5 ±5, 2.5, 1, 0.5

Configurable Per-Channel

-

Trigger Mode

Pacer/Software/ External Pulse

Analog Slope - - - - - - - - - - - - - - - -

Pre-trigger - - - - - - - - - - - - - - - -

Post-trigger - - - - - - - - - - - - - - - -

About-trigger - - - - - - - - - - - - - - - -

Data Transfer Mode

Software

DMA - - - Bus-mastering Bus-mastering - - Bus-mastering - SS** SM** SM** SM** SS** SS** SS** - Bus-mastering Bus-mastering

Analog Output

Resolution 12 bits 12 bits 12 bits 12 bits 16 bits 12 bits 16 bits 16 bits 12 bits 12 bits 12 bits 12 bits 12 bits - - 12 bits - - -

Number of Channels

2 (PCI-1710 only)

2 (PCI-1710HG only)

2 (PCI-1711 only)

2 (PCI-1712 only)

2 (PCI-1716 only)

1 1 2 1 2 1 1 1 - - 1 - - -

Onboard FIFO - - - 32,768 samples - - - - - - - - - - - - - - -

Output Range (V) 0 ~ 5, 0 ~ 10 0 ~ 5, 0 ~ 10 0 ~ 5, 0 ~ 100 ~ 5, 0 ~ 10, ±5,

±100 ~ 5, 0 ~ 10, ±5,

±100 ~ 5, 0 ~ 10 ±5, ±10

0 ~ 5, 0 ~ 10 ±5, ±10

0 ~ 5, 0 ~ 10 0 ~ 5, 0 ~ 10 0 ~ 5, 0 ~ 100 ~ 5, 0 ~ 10,

±10 0 ~ 5, 0 ~ 10,

±10 - - 0 ~ 5, 0 ~ 10 - - -

Throughput Static update Static update Static update 1 MS/s Static update Static update Static update Static update Static update Static update Static update Static update Static update - - Static update - - -

DMA transfer - - - - - - - - - - - - - - - - - -

Digital I/OInput Channels 16 16 16 16

(shared)16 16 16 16 16 16 16 16 16 16

(shared)16

(shared)16

(shared)- - -

Output Channels 16 16 16 16 16 16 16 16 16 16 16 16 - - -

Timer/Counter

Channels 1 1 1 3 1 1 1 1 - 1 1 1 1 1 1 1 - - -

Resolution 16 bits 16 bits 16 bits 16 bits 16 bits 16 bits 16 bits 16 bits - 16 bits 16 bits 16 bits 16 bits 16 bits 16 bits 16 bits - - -

Time Base 10 MHz 10 MHz 10 MHz 10 MHz 10 MHz 10 MHz 10 MHz 10 MHz - 2 MHz 10 MHz 10 MHz 10 MHz 10 MHz 10 MHz 10 MHz - - -

Isolation Voltage - - - - - - - - - - - - - - - - 2,500 VDC - -

Auto Calibration - - - - - - - - - - - - -

BoardID Switch - - - - - - - - - - -

Dimensions (mm) 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 185 x 100 155 x 100 185 x 100 185 x 100 96 x 90 96 x 90 96 x 90 175 x 100 175 x 100 175 x 100

Connector 68-pin SCSI 68-pin SCSI 68-pin SCSI 68-pin SCSI 68-pin SCSI DB37 68-pin SCSI 68-pin SCSI 3 x 20-pin 5 x 20-pin DB37 DB37 DB37 2 x 20-pin 2 x 20-pin 2 x 20-pin DB37 4 x BNC 4 x BNC

Windows 2000/XP DLL Driver

Windows Vista DLL Driver - - - - - - - -

Windows 2000/XP SDK

Win CE 5.0/6.0 Driver - - - - - - - - - - - - - - - -

Linux Driver - - - - -

ActiveDAQ/ActiveDAQ Pro

Labview I/O Drivers

Mathworks MATLAB Data Acquisiton Tool Box 2.5.1

- - - - - - - - -

KW IPC-33 Driver - - - - - - - - - - - - - - - -

Page 9-14 9-14 9-16 9-18 9-20 9-22 9-24 9-24 9-26 9-27 9-28 9-28 9-28 9-61 9-61 9-61 9-30 9-32 9-32

Analog I/O & Multifunction Card Selection Guide

*Note: All channels should be set to the same range.


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Category Multifunction Multifunction AI

Bus PCI PCI ISA PC/104 PCI

Model PCI-1710/L PCI-1710HG/L PCI-1711/L PCI-1712/L PCI-1716/L PCI-1718HDU PCI-1741U PCI-1742U PCL-711B PCL-812PG PCL-818L PCL-818HD PCL-818HG PCM-3718H PCM-3718HG PCM-3718HO PCI-1713 PCI-1714U PCI-1714UL

Anal

og In

put

General Spec.

Resolution 12 bits 12 bits 12 bits 12 bits 16 bits 12 bits 16 bits 16 bits 12 bits 12 bits 12 bits 12 bits 12 bits 12 bits 12 bits 12 bits 12 bits 12 bits 12 bits

Channels 16 SE/8 Diff. 16 SE/8 Diff. 16 SE 16 SE/8 Diff. 16 SE/8 Diff. 16 SE/8 Diff. 16 SE/8 Diff. 16 SE/8 Diff. 8 SE 16 SE 16 SE/8 Diff 16 SE/8 Diff 16 SE/8 Diff 16 SE/8 Diff. 16 SE/8 Diff. 16 SE/8 Diff. 32 SE/16 Diff. 4 SE 4 SE

Onboard FIFO 4,096 samples 4,096 samples 1,024 samples 1,024 samples 1,024 samples 1,024 samples 1,024 samples 1,024 samples - - - 1,024 samples 1,024 samples - - 1,024 samples 4,096 samples 32,768 samples 8,192 samples

Sampling Rate 100 kS/s 100 kS/s 100 kS/s 1 MS/s 250 kS/s 100 kS/s 200 kS/s 1 MS/s 40 kS/s 30 kS/s 40 kS/s 100 kS/s 100 kS/s 100 kS/s 100 kS/s 100 kS/s* 100 kS/s 30 MS/s 10 MS/s

Auto Channel Scanning

- -

Input Ranges

Unipolar Inputs (V)0 ~ 10, 0 ~ 5,

0 ~ 2.5, 0 ~ 1.25

0 ~ 10, 0 ~ 1, 0 ~ 0.1, 0 ~ 0.01

-0 ~ 10, 0 ~ 5,

0 ~ 2.5, 0 ~ 1.25

0 ~ 10, 0 ~ 5, 0 ~ 2.5, 0 ~ 1.25

0 ~ 10, 0 ~ 5, 0 ~ 2.5, 0 ~ 1.25

0 ~ 10, 0 ~ 5,

0 ~ 2.5, 0 ~ 1.25*

0 ~ 10, 0 ~ 5 0 ~ 2.5,

0 ~ 0.125- - -

0 ~ 10, 0 ~ 5, 0 ~ 2.5, 0 ~ 1.25

0 ~ 10, 0 ~ 1, 0 ~ 0.1, 0 ~ 0.01

0 ~ 10, 0 ~ 5 0 ~ 2.5,

0 ~ 0.125

0 ~ 10, 0 ~ 1 0 ~ 0.1, 0 ~ 0.01

0 ~ 10, 0 ~ 5 0 ~ 2.5,

0 ~ 0.125

0 ~ 10, 0 ~ 5, 0 ~ 2.5, 0 ~ 1.25

- -

Bipolar Inputs (V) ±10, 5, 2.5, 1.25, 0.625

±10, 5, 1, 0.5, 0.1, 0.05, 0.01, 0.005

±10, 5, 2.5, 1.25, 0.625

±10, 5, 2.5, 1.25, 0.625

±10, 5, 2.5, 1.25, 0.625

±10, 5, 2.5, 1.25, 0.625

±10, 5, 2.5, 1.25, 0.625*

±10, 5, 2.5, 1.25 0.625

±5, 2.5, 1.25, 0.625, 0.3125

±10, 5, 2.5, 1.25, 0.625,

0.3125

±10, 5, 2.5, 1.25, 0.625

±10, 5, 2.5, 1.25, 0.625

±10, 5, 1, 0.5, 0.1, 0.05, 0.01,

0.005

±10, 5, 2.5, 1.25 0.625

±10, 5, 1, 0.5, 0.1,

0.05, 0.01, 0.005

±10, 5, 2.5, 1.25 0.625

±10, 5, 2.5, 1.25, 0.625

±5, 2.5, 1, 0.5 ±5, 2.5, 1, 0.5

Configurable Per-Channel

-

Trigger Mode


Analog Slope - - - - - - - - - - - - - - - -

Pre-trigger - - - - - - - - - - - - - - - -

Post-trigger - - - - - - - - - - - - - - - -

About-trigger - - - - - - - - - - - - - - - -

Data Transfer Mode

Software

DMA - - - Bus-mastering Bus-mastering - - Bus-mastering - SS** SM** SM** SM** SS** SS** SS** - Bus-mastering Bus-mastering

Analog Output

Resolution 12 bits 12 bits 12 bits 12 bits 16 bits 12 bits 16 bits 16 bits 12 bits 12 bits 12 bits 12 bits 12 bits - - 12 bits - - -

Number of Channels

2 (PCI-1710 only)

2 (PCI-1710HG only)

2 (PCI-1711 only)

2 (PCI-1712 only)

2 (PCI-1716 only)

1 1 2 1 2 1 1 1 - - 1 - - -

Onboard FIFO - - - 32,768 samples - - - - - - - - - - - - - - -

Output Range (V) 0 ~ 5, 0 ~ 10 0 ~ 5, 0 ~ 10 0 ~ 5, 0 ~ 100 ~ 5, 0 ~ 10, ±5,

±100 ~ 5, 0 ~ 10, ±5,

±100 ~ 5, 0 ~ 10 ±5, ±10

0 ~ 5, 0 ~ 10 ±5, ±10

0 ~ 5, 0 ~ 10 0 ~ 5, 0 ~ 10 0 ~ 5, 0 ~ 100 ~ 5, 0 ~ 10,

±10 0 ~ 5, 0 ~ 10,

±10 - - 0 ~ 5, 0 ~ 10 - - -

Throughput Static update Static update Static update 1 MS/s Static update Static update Static update Static update Static update Static update Static update Static update Static update - - Static update - - -

DMA transfer - - - - - - - - - - - - - - - - - -

Digital I/OInput Channels 16 16 16 16

(shared)16 16 16 16 16 16 16 16 16 16

(shared)16

(shared)16

(shared)- - -

Output Channels 16 16 16 16 16 16 16 16 16 16 16 16 - - -

Timer/Counter

Channels 1 1 1 3 1 1 1 1 - 1 1 1 1 1 1 1 - - -

Resolution 16 bits 16 bits 16 bits 16 bits 16 bits 16 bits 16 bits 16 bits - 16 bits 16 bits 16 bits 16 bits 16 bits 16 bits 16 bits - - -

Time Base 10 MHz 10 MHz 10 MHz 10 MHz 10 MHz 10 MHz 10 MHz 10 MHz - 2 MHz 10 MHz 10 MHz 10 MHz 10 MHz 10 MHz 10 MHz - - -

Isolation Voltage - - - - - - - - - - - - - - - - 2,500 VDC - -

Auto Calibration - - - - - - - - - - - - -

BoardID Switch - - - - - - - - - - -

Dimensions (mm) 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 185 x 100 155 x 100 185 x 100 185 x 100 96 x 90 96 x 90 96 x 90 175 x 100 175 x 100 175 x 100

Connector 68-pin SCSI 68-pin SCSI 68-pin SCSI 68-pin SCSI 68-pin SCSI DB37 68-pin SCSI 68-pin SCSI 3 x 20-pin 5 x 20-pin DB37 DB37 DB37 2 x 20-pin 2 x 20-pin 2 x 20-pin DB37 4 x BNC 4 x BNC


Windows Vista DLL Driver - - - - - - - -

Windows 2000/XP SDK

Win CE 5.0/6.0 Driver - - - - - - - - - - - - - - - -

Linux Driver - - - - -

ActiveDAQ/ActiveDAQ Pro

Labview I/O Drivers

Mathworks MATLAB Data Acquisiton Tool Box 2.5.1

- - - - - - - - -

KW IPC-33 Driver - - - - - - - - - - - - - - - -

-14 9-14 9-16 9-18 9-20 9-22 9-24 9-24 9-26 9-27 9-28 9-28 9-28 9-61 9-61 9-61 9-30 9-32 9-32

Selection Guide

* 80 kHz on P4-based (or upper) system** SS = Single DMA channel, Single A/D channel scan SM = Single DMA channel, Multiple A/D channel scan


Category AI AOBus PCI ISA PCI-104 PCI ISAModel PCI-1715U PCI-1747U PCL-813B PCM-3813I PCI-1720U PCI-1721 PCI-1723 PCI-1724U PCL-726 PCL-727 PCL-728

Anal

og In

put

General Spec.

Resolution 12 bits 16 bits 12 bits 12 bits - - - - - - -

Channels 32 SE/16 Diff.

64 SE/32 Diff. 32 SE 32 SE/8 Diff. - - - - - - -

Onboard FIFO 1,024 samples

1,024 samples - 1,024

samples - - - - - - -

Sampling Rate 500 kS/s 250 kS/s 25 kS/s 100 kS/s - - - - - - -Auto Channel Scanning - - - - - - - -

Input Ranges

Unipolar Inputs (V)

0 ~10, 0 ~ 5

0 ~ 2.5, 0 ~ 0.125

0 ~ 10, 0 ~ 5,

0 ~ 2.5, 0 ~ 1.25

0 ~ 10, 0 ~ 5,

0 ~ 2.5, 0 ~ 1.25

0 ~ 10, 0 ~ 5,

0 ~ 2.5, 0 ~ 1.25

- - - - - - -

Bipolar Inputs (V)

±10, 5, 2.5, 1.25, 0.625

±10, 5, 2.5, 1.25,

0.625

5, 2.5, 1.25, 0.625

5, 2.5, 1.25, 0.625 - - - - - - -

Configurable Per-Channel - - - - - - -

Trigger Mode


Pacer/ Software

Software only

- - - - - - -

Analog Slope - - - - - - - - - - -Pre-trigger - - - - - - - - - - -Post-trigger - - - - - - - - - - -About-trigger - - - - - - - - - - -

Data Transfer Mode

Software Software

only - - - - - -

DMA Bus-mastering

Bus-mastering - - - - - - - - -

Analog Output

Resolution - - - - 12 bits 12 bits 16 bits 14 bits 12 bits 12 bits 12 bits

Number of Channels - - - - 4

4 (Waveform

Output)8 32 6 12 2

Onboard FIFO - - - - - 1,024 samples - - - - -

Output Range (V) - - - -

0 ~ 5, 0 ~ 10, ±5, ±10,

0 ~ 20 mA, 4 ~ 20 mA

0 ~ 5, 0 ~ 10,

±5, ±10, 0 ~ 20 mA, 4 ~ 20 mA

-10 ~ 10 0 ~ 20 mA, 4 ~ 20 mA

±10, 0 ~ 20 mA

0 ~ 5, 0 ~ 10, ±5, ±10,

4 ~ 20 mA

-0 ~ 5, 0 ~ 10, ±5, 4 ~ 20 mA

0 ~ 5, 0 ~ 10,

±5, ±10, 0 ~ 20 mA, 4 ~ 20 mA

Throughput - - - - Static update 10M Static

updateStatic update

Static update

Static update

Static update

DMA Transfer - - - - - Bus-mastering - - - - -

Digital I/OInput Channels - - - - -

16 (shared)

16 (shared) -

16 16 -Output Channels - - - - - 16 16 -

Timer/CounterChannels - - - - - 1 - - - - -Resolution - - - - - 16 bits - - - - -Time Base - - - - - 10 MHz - - - - -

Isolation Voltage 2,500 VDC - 500 VDC 2,500 VDC 2,500 VDC - - 1,500 VDC - - 500 VDC

Auto Calibration - - - - - - - -BoardID Switch - - - - -Dimensions (mm) 175 x 100 175 x 100 219 x 100 96 x 90 175 x 100 175 x 100 175 x 100 175 x 100 337 x 112 337 x 112 185 x 120

Connector DB37 68-pin SCSI DB37 40-pin DB37 68-pin

SCSI68-pin SCSI DB62 4 x 20-pin 2 x 20-pin,

DB37 2 x DB9


Windows Vista DLL Driver - - - - -Windows 2000/XP SDK

Win CE 5.0/6.0 Driver - - - - - - - - -Linux Driver - - - -

ActiveDAQ/ActiveDAQ Pro Labview I/O Drivers Mathworks MATLAB Data Acquisiton Tool Box 2.5.1 - - - - - -

KW IPC-33 Driver - - - - - - - - - - -Page 9-31 9-33 9-34 9-61 9-35 9-36 9-37 9-38 9-40 9-39 9-40

Analog I/O & Multifunction Card Selection Guide


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Bus

Digital I/O & Counter Card Selection GuideCategory Non-Isolated Digital I/O

Bus PCI ISA

Model PCI-1737U PCI-1739U PCI-1751 PCI-1753 PCI-1757UP PCL-720+ PCL-722 PCL-724 PCL-731

TTL

DI/O

Input Channels 24 (shared)

48 (shared)

48 (shared)

96 (shared)

24 (shared)

32 144 (shared)

24 (shared)

48 (shared)Output Channels 32

Output Channel

Sink Current 24 mA @ 0.4 V 24 mA @ 0.4 V 24 mA @ 0.4 V 24 mA @ 0.44 V 24 mA @ 0.5 V 24 mA @ 0.5 V 24 mA @ 0.5 V 24 mA @ 0.4 V 24 mA @ 0.4 V

Source Current 15 mA @ 2.4 V 15 mA @ 2.4 V 15 mA @ 2.4 V 24 mA @ 3.76 V 24 mA @ 3.7 V 15 mA @ 2.0 V 15 mA @ 2.4 V 15 mA @ 2.4 V 15 mA @ 2.4 V

Isol

ated

DI/O

Input

Channels - - - - - - - - -

Isolation Voltage - - - - - - - - -

Input Range - - - - - - - - -

Output

Channels - - - - - - - - -

Isolation Voltage - - - - - - - - -

Output Range - - - - - - - - -

Max. Sink Current - - - - - - - - -

Timer/Counter

Channels - - 3 - - 3 - - -

Resolution - - 16 bits - - 16 bits - - -

Time Base - - 10 MHz - - 1 MHz - - -

Adva

nced

Fun

ctio

n

Pattern Match - - - - - - - -

Change of State - - - - - - - -

BoardID Switch - - - -

Channel-Freeze Function - - - - - - - - -

Output Status Read Back -

Dry/Wet Contact* - - - - - -

Dimensions (mm) 175 x 100 175 x 100 175 x 100 175 x 100 120 x 65 185 x 100 334 x 100 125 x 100 185 x 100

Connector 1 x 50-pin 2 x 50-pin 68-pin SCSI 100-pin SCSI 1 x DB25 5 X 20-pin 6 x 50-pin 1 x 50-pin 2 x 50-pin


Windows Vista DLL Driver - - - -

Windows 2000/XP SDK

Win CE 5.0/6.0 Driver - - - - - - - - -

Linux Driver - - - -

ActiveDAQ/ ActiveDAQ Pro

Labview I/O Drivers

Mathworks MATLAB & Simulink Data Acquisiton Tool Box 2.5.1

- - -

KW IPC-33 Driver - - - - - - - - -

Page 9-41 9-42 9-43 9-44 9-45 9-46 9-47 9-48 9-49

* Dry/wet contact can be mixed at the same time within one group.


Category Non-Isolated Digital I/O Isolated Digital I/O Isolated Digital I/O Counter

Bus PC/104 PCI-104 PCI PCI ISA PC/104 PCI-104 PCI ISA PC/104

Model PCM-3724 PCM-3753I PCI-1730 PCI-1733 PCI-1734 PCI-1750 PCI-1752U PCI-1754 PCI-1756 PCI-1758UDI PCI-1758UDO PCI-1760U PCI-1761 PCI-1762 PCL-725 PCL-735 PCM-3725 PCM-3730 PCM-3730I PCM-3761I PCI-1780U PCL-836 PCM-3780

TTL

DI/O

Input Channels48 (shared) 96 (shared)

16 - - - - - - - - - - - - - 8 16 - - 8 16 24

Output Channels 16 - - - - - - - - - - - - - 8 16 - - 8 16

Output Channel

Sink Current 24 mA @ 0.5 V

24 mA @ 0.4 V

24 mA @ 0.5 V - - - - - - - - - - - - - - 0.5 V @

8 mA - - 24 mA @ 0.5 V

8 mA @ 0.5 V

24 mA @ 0.5 V

Source Current 15 mA @ 2.0 V

15 mA @ 2.4 V

15 mA @ 2.4 V - - - - - - - - - - - - -0.4 mA @

2.4 V - - 15 mA @ 2.4 V

0.4 mA @ 2.4 V

15 mA @ 2.0 V

Isol

ated

DI/O

Input

Channels - - 16 (Sink) 32 (Sink) - 16 (Sink) - 64 (Sink) 32 (Sink) 128 - 8 (Sink) 8 (Sink) 16 (Sink) 8 (Sink) - 8 8 16 8 - - -

Isolation Voltage - - 2,500 VDC 2,500 VDC - 2,500 VDC - 2,500 VDC 2,500 VDC 2,500 VRMS - 2,500 VDC 3,750 VDC 2,500 VDC 1,500 VDC - 2,500 VDC 2,500 VDC 2,500 VDC 2,500 VDC - - -

Input Range - - 5 ~ 30 VDC 5 ~ 30 VDC - 5 ~ 50 VDC - 10 ~ 50 VDC 10 ~ 50 VDC 5 ~ 25 VDC - 4.5 ~ 12 VDC 5 ~ 50 VDC 10 ~ 50 VDC 5 ~ 24 VDC - 10 ~ 50 VDC 5 ~ 24 VDC 5 ~ 30 VDC 5 ~ 30 VDC - - -

Output

Channels - - 16 (Sink) - 32 (Sink) 16 (Sink) 64 (Sink) - 32 (Sink) - 128 6 x Form A 2 x Form C

4 x Form A 4 x Form C 16* 4 x Form A

4 x Form C 12 x Form C 8 x Form C 8 16 8 x Form C - - -

Isolation Voltage - - 2,500 VDC - 2,500 VDC 2,500 VDC 2,500 VDC - 2,500 VDC - 2,500 VRMS 2,500 VDC 2,500 VDC 2,500 VDC 1,000 VDC 1,000 VDC 2,000 VDC 2,500 VDC 2,500 VDC 2,000 VDC - - -

Output Range - - 5 ~ 40 VDC - 5 ~ 40 VDC 5 ~ 40 VDC 5 ~ 40 VDC - 5 ~ 40 VDC - 5 ~ 40 VDC 0.5A @ 120 VAC

1A @ 30 VDC

3A @ 250 VAC

3A @ 24 VDC

3A @ 250 VAC

3A @ 24 VDC

0.5A @ 120 VAC

1A @ 30 VDC

1A @ 125 VAC

2A @ 30 VDC

0.25A @ 240 VAC 1A @ 30

VDC

5 ~ 40 VDC 5 ~ 30 VDC 0.25 A @ 240 VAC

1 A @ 30 VDC

-

- -

Max. Sink Current - - 200 mA - 200 mA 200 mA 200 mA - 200 mA - 90 mA 200 mA 350 mA - -

Timer/Counter

Channels - - - - - 1 - - - - -Up CTR for DI

2 x PWM- - - - - - - - 8 x CTR 6 x CTR

3 x PWM 2

Resolution - - - - - 16 bits - - - - -16 bits (2,500

Isolation)- - - - - - - - 16-bit 16-bit 16 bits

Time Base - - - - - 1 MHz - - - - - 500 Hz for Up CTR - - - - - - - - 20 MHz 10 MHz 20 MHz

Adva

nced

Fun

ctio

n

Pattern Match - - - - - - - - - - - - - - - - - - - - -

Change of State - - - - - - - - - - - - - - - - - - - - -

BoardID Switch - - - - - - - - - -

Channel-Freeze Function - - - - - - - - - - - - - - - - - - -

Output Status Read Back - - - - - - - - - - - -

Dry/Wet Contact* - - - - - - - - - - - - - - - - - - - -

Dimensions (mm) 96 x 90 96 x 90 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 147 x 95 155 x 100 96 x 90 96 x 90 96 x 90 96 x 90 175 x 100 185 x 100 96 x 90

Connector 2 x 50-pin 4 x 50-pin 1 x DB37 4 x 20-pin 1 x DB37 1 x DB37 1 x DB37 100-pin

SCSI100-pin

SCSI100-pin

SCSI

dual 100-pin

mini-SCSI

dual 100-pin

mini-SCSI1 x DB37 1 x DB37 1 x DB62 1 x DB37 1 x DB37 1 x 20-pin

1 x 50-pin 3 x 20-pin 2 x 20-pin 1 x 20-pin 1 x 50-pin

68-pin SCSI

1 x DB37 2 x 20-pin

1 x 50-pin 1 x 20-pin


Windows Vista DLL Driver - - - - - - - - - -

Windows 2000/XP SDK

Win CE 5.0/6.0 Driver - - - - - - - - - - - - - - - -

Linux Driver - - - - - - - - -

ActiveDAQ/ActiveDAQ Pro - - -

Labview I/O Drivers

Mathworks MATLAB & Simulink Data Acquisiton Tool Box 2.5.1 - - - - - - - - - -

KW Win33 Driver - - - - - - - - - - - - -

Page 9-61 9-63 9-50 9-50 9-50 9-51 9-52 9-52 9-52 9-53 9-53 9-54 9-55 9-56 9-57 9-58 9-62 9-62 9-63 9-63 9-59 9-60 9-62

* Dry/wet contact can be mixed at the same time within one group.

Digital I/O & Counter Card Selection Guide


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Selection Guide

Category Non-Isolated Digital I/O Isolated Digital I/O Isolated Digital I/O Counter

Bus PC/104 PCI-104 PCI PCI ISA PC/104 PCI-104 PCI ISA PC/104

Model PCM-3724 PCM-3753I PCI-1730 PCI-1733 PCI-1734 PCI-1750 PCI-1752U PCI-1754 PCI-1756 PCI-1758UDI PCI-1758UDO PCI-1760U PCI-1761 PCI-1762 PCL-725 PCL-735 PCM-3725 PCM-3730 PCM-3730I PCM-3761I PCI-1780U PCL-836 PCM-3780

TTL

DI/O

Input Channels48 (shared) 96 (shared)

16 - - - - - - - - - - - - - 8 16 - - 8 16 24

Output Channels 16 - - - - - - - - - - - - - 8 16 - - 8 16

Output Channel

Sink Current 24 mA @ 0.5 V

24 mA @ 0.4 V

24 mA @ 0.5 V - - - - - - - - - - - - - - 0.5 V @

8 mA - - 24 mA @ 0.5 V

8 mA @ 0.5 V

24 mA @ 0.5 V

Source Current 15 mA @ 2.0 V

15 mA @ 2.4 V

15 mA @ 2.4 V - - - - - - - - - - - - -0.4 mA @

2.4 V - - 15 mA @ 2.4 V

0.4 mA @ 2.4 V

15 mA @ 2.0 V

Isol

ated

DI/O

Input

Channels - - 16 (Sink) 32 (Sink) - 16 (Sink) - 64 (Sink) 32 (Sink) 128 - 8 (Sink) 8 (Sink) 16 (Sink) 8 (Sink) - 8 8 16 8 - - -

Isolation Voltage - - 2,500 VDC 2,500 VDC - 2,500 VDC - 2,500 VDC 2,500 VDC 2,500 VRMS - 2,500 VDC 3,750 VDC 2,500 VDC 1,500 VDC - 2,500 VDC 2,500 VDC 2,500 VDC 2,500 VDC - - -

Input Range - - 5 ~ 30 VDC 5 ~ 30 VDC - 5 ~ 50 VDC - 10 ~ 50 VDC 10 ~ 50 VDC 5 ~ 25 VDC - 4.5 ~ 12 VDC 5 ~ 50 VDC 10 ~ 50 VDC 5 ~ 24 VDC - 10 ~ 50 VDC 5 ~ 24 VDC 5 ~ 30 VDC 5 ~ 30 VDC - - -

Output

Channels - - 16 (Sink) - 32 (Sink) 16 (Sink) 64 (Sink) - 32 (Sink) - 128 6 x Form A 2 x Form C

4 x Form A 4 x Form C 16* 4 x Form A

4 x Form C 12 x Form C 8 x Form C 8 16 8 x Form C - - -

Isolation Voltage - - 2,500 VDC - 2,500 VDC 2,500 VDC 2,500 VDC - 2,500 VDC - 2,500 VRMS 2,500 VDC 2,500 VDC 2,500 VDC 1,000 VDC 1,000 VDC 2,000 VDC 2,500 VDC 2,500 VDC 2,000 VDC - - -

Output Range - - 5 ~ 40 VDC - 5 ~ 40 VDC 5 ~ 40 VDC 5 ~ 40 VDC - 5 ~ 40 VDC - 5 ~ 40 VDC 0.5A @ 120 VAC

1A @ 30 VDC

3A @ 250 VAC

3A @ 24 VDC

3A @ 250 VAC

3A @ 24 VDC

0.5A @ 120 VAC

1A @ 30 VDC

1A @ 125 VAC

2A @ 30 VDC

0.25A @ 240 VAC 1A @ 30

VDC

5 ~ 40 VDC 5 ~ 30 VDC 0.25 A @ 240 VAC

1 A @ 30 VDC

-

- -

Max. Sink Current - - 200 mA - 200 mA 200 mA 200 mA - 200 mA - 90 mA 200 mA 350 mA - -

Timer/Counter

Channels - - - - - 1 - - - - -Up CTR for DI

2 x PWM- - - - - - - - 8 x CTR 6 x CTR

3 x PWM 2

Resolution - - - - - 16 bits - - - - -16 bits (2,500

Isolation)- - - - - - - - 16-bit 16-bit 16 bits

Time Base - - - - - 1 MHz - - - - - 500 Hz for Up CTR - - - - - - - - 20 MHz 10 MHz 20 MHz

Adva

nced

Fun

ctio

n

Pattern Match - - - - - - - - - - - - - - - - - - - - -

Change of State - - - - - - - - - - - - - - - - - - - - -

BoardID Switch - - - - - - - - - -

Channel-Freeze Function - - - - - - - - - - - - - - - - - - -

Output Status Read Back - - - - - - - - - - - -

Dry/Wet Contact* - - - - - - - - - - - - - - - - - - - -

Dimensions (mm) 96 x 90 96 x 90 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 175 x 100 147 x 95 155 x 100 96 x 90 96 x 90 96 x 90 96 x 90 175 x 100 185 x 100 96 x 90

Connector 2 x 50-pin 4 x 50-pin 1 x DB37 4 x 20-pin 1 x DB37 1 x DB37 1 x DB37 100-pin

SCSI100-pin

SCSI100-pin

SCSI

dual 100-pin

mini-SCSI

dual 100-pin

mini-SCSI1 x DB37 1 x DB37 1 x DB62 1 x DB37 1 x DB37 1 x 20-pin

1 x 50-pin 3 x 20-pin 2 x 20-pin 1 x 20-pin 1 x 50-pin

68-pin SCSI

1 x DB37 2 x 20-pin

1 x 50-pin 1 x 20-pin


Windows Vista DLL Driver - - - - - - - - - -

Windows 2000/XP SDK

Win CE 5.0/6.0 Driver - - - - - - - - - - - - - - - -

Linux Driver - - - - - - - - -

ActiveDAQ/ActiveDAQ Pro - - -

Labview I/O Drivers

Mathworks MATLAB & Simulink Data Acquisiton Tool Box 2.5.1 - - - - - - - - - -

KW Win33 Driver - - - - - - - - - - - - -

Page 9-61 9-63 9-50 9-50 9-50 9-51 9-52 9-52 9-52 9-53 9-53 9-54 9-55 9-56 9-57 9-58 9-62 9-62 9-63 9-63 9-59 9-60 9-62

* Dry/wet contact can be mixed at the same time within one group. * Jumper selectable Form A/Form B-type relay output


Features

SpecificationsAnalog Input

Channels 16 single-ended/ 8 differential (software programmable)Resolution 12 bitsFIFO Size 4,096 samplesOvervoltage Protection 30Vp-pInput Impedance 1 GWSampling Modes Software, onboard programmable pacer and externalInput Range (V, software programmable)

PCI-1710/1710LGain 0.5 1 2 4 8Bipolar ±10 ±5 ±2.5 ±1.25 ±0.625Unipolar N/A 0 ~ 10 0 ~ 5 0 ~ 2.5 0 ~ 1.25Accuracy (% of FSR ±1LSB) 0.1 0.1 0.2 0.2 0.4

PCI-1710HG/1710HGLGain 0.5 1 5 10 50 100 500 1000Bipolar ±10 ±5 ±1 ±0.5 ±0.1 ±0.05 ±0.01 ±0.005Unipolar N/A 0 ~ 10 N/A 0 ~ 1 N/A 0 ~ 0.1 N/A 0 ~ 0.01Accuracy (% of FSR ±1LSB) 0.1 0.1 0.2 0.2 0.4 0.4 0.8 0.8

Maximum Sampling Rate (S/s, depending on PGIA setting time)

Model Gain Max. Sampling RatePCI-1710/1710L 0.5, 1, 2, 4, 8 100 kS/s

PCI-1710HG/1710HGL

0.5, 1 100 kS/s5, 10 35 kS/s

20, 100 7 kS/s500, 1000 770 S/s

Analog Output (PCI-1710/1710HG only)Channels 2Resolution 12 bitsOutput Rate Static updateOutput Range (V, software programmable)

PCI-1710/LPCI-1710HG/HGL

16-ch single-ended or 8-ch differential or a combination of analog input

12-bit A/D converter, with up to 100 kHz sampling rate

Programmable gain

Automatic channel/gain scanning

Onboard FIFO memory (4,096 samples)

Two 12-bit analog output channels (PCI-1710/1710HG only)

16-ch digital input and 16-ch digital output

Onboard programmable counter

BoardID™ switch

100 kS/s, 12-bit, 16-ch PCI Multifunction Card100 kS/s, 12-bit, 16-ch PCI Multifunction Card with High Gain

Internal Reference Unipolar 0 ~ +5 0 ~ +10 V

External Reference 0 ~ +x V @ -x V (-10 ≤ x ≤ 10)

Slew Rate 10 V/µsDriving Capability 3 mAOperation Mode Software pollingAccuracy INLE: ±1 LSB, DNLE: ±1 LSB

Digital InputChannels 16 Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min.

Digital OutputChannels 16Compatibility 5 V/TTLOutput Voltage Logic 0: 0.4 V max.

Logic 1: 2.4 V min. Output Capability Sink: 8.0 mA @ 0.8 V

Source: -0.4 mA @ 2.0 V

Pacer/CounterChannels 1Resolution 16 bitsCompatibility 5 V/TTLMax. Input Frequency 1 MHz

IntroductionThe PCI-1710 Series are multifunction cards for the PCI bus. Their advanced circuit design provides higher quality and more functions, including the five most desired measurement and control functions: 12-bit A/D conversion, D/A conversion, digital input, digital output, and counter/timer.

RoHSCOMPLIANT2002/95/EC


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Specifications ContinuedGeneral

Bus Type PCI V2.2I/O Connector 1 x 68-pin SCSI female connectorDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: 5 V @ 850 mA

Max: 5 V @ 1.0 AOperating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95% RH non-condensing (refer to IEC 68-2-3)

Ordering InformationPCI-1710 100 kS/s, 12-bit Multifunction CardPCI-1710L 100 kS/s, 12-bit Multifunction Card w/o AOPCI-1710HG 100 kS/s, 12-bit High-gain Multifunction CardPCI-1710HGL 100 kS/s, 12-bit High-gain Multi. Card w/o AOPCLD-8710 DIN-rail Wiring Board w/ CJCPCL-10168-1 68-pin SCSI Shielded Cable, 1 mPCL-10168-2 68-pin SCSI Shielded Cable, 2 mADAM-3968 68-pin DIN-rail SCSI Wiring Board

PCI-1710/LPCI-1710HG/HGL

Pin Assignments


Features


Channels 16 single-endedResolution 12 bitsMax. Sampling Rate 100 kS/sFIFO Size 1,024 samplesOvervoltage Protection 30 Vp-pInput Impedance 2 MW/5 pFSampling Modes Software, onboard programmable pacer, or externalInput Range (V, software programmable)

Bipolar ± 10 ± 5 ± 2.5 ± 1.25 ± 0.625Accuracy (% of FSR ±1LSB) 0.1 0.1 0.2 0.2 0.4

Analog Output (PCI-1711 only)Channels 2Resolution 12 bitsOutput Rate Static updateOutput Range (V, software programmable)

Internal Reference Unipolar 0 ~ +5, 0 ~ +10External Reference 0 ~ +x V @ -x V (-10 ≤ x ≤ 10)

Slew Rate 11 V/µsDriving Capability 3 mAOutput Impedance 0.81 WOperation Mode Software pollingAccuracy INLE: ±1 LSB

DNLE: ±1 LSB

Digital InputsChannels 16Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min.

16-ch single-ended analog input


Programmable gain



Two 12-bit analog output channels (PCI-1711 only)



PCI-1711/L Entry-level 100 kS/s, 12-bit, 16-ch PCI Multifunction Card

Digital OutputsChannels 16Compatibility 5 V/TTLOutput Voltage Logic 0: 0.8 V

Logic 1: 2.0 VOutput Capability Sink: 8.0 mA @ 0.8 V

Source: -0.4 mA @ 2.0 V

Pacer/CounterChannels 1Resolution 16 bitsCompatibility 5 V/TTLMax. Input Frequency 10 MHzReference Clock Internal: 10 MHz

GeneralBus Type PCI V2.2I/O Connector 1 x 68-pin SCSI female connectorDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power ConsumptionPCI-1711 Typical: +5 V @ 850 mA Max: +5 V @ 1.0 A PCI-1711L Typical: +5 V @ 700 mA Max: +5 V @ 1.0 AOperating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95% RH non-condensing (refer to IEC 68-2-3)

IntroductionPCI-1711 and PCI-1711L are powerful, but low-cost multifunction cards for the PCI bus. PCI-1711 comes with 2 analog output channels, while the PCI-1711L doesn’t. Thus, PCI-1711L represents a cost saver for those that do not need analog output.



8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Ordering InformationPCI-1711 Entry-level 100 kS/s, 12-bit Multifunction CardPCI-1711L Entry-level 100 kS/s, 12-bit Multi. Card w/o AOPCLD-8710 DIN-rail Wiring Board w/ CJCPCL-10168-1 68-pin SCSI Shielded Cable, 1 mPCL-10168-2 68-pin SCSI Shielded Cable, 2 mADAM-3968 68-pin DIN-rail SCSI Wiring Board

PCI-1711/L

Pin Assignments


Features



Channels 16 single-ended/ 8 differential (software programmable)Resolution 12 bitsMax. Sampling Rate Multi-channel, single gain: 1 MS/s

Multi-channel, multi gain: 600 kS/s Multi-channel, multi gain, unipolar/bipolar: 400 kS/s

FIFO Size 1,024 samplesOvervoltage Protection 30 Vp-pInput Impedance 100 MW/10 pF (Off), 100 MW/100 pF (On)Sampling Modes Software, onboard programmable pacer and externalTrigger Modes Pre-trigger, post-trigger, delay-trigger and about-

triggerInput Range (V, software programmable)

Unipolar N/A 0 ~ 10 0 ~ 5 0 ~ 2.5 0 ~ 1.25Bipolar ±10 ±5 ±2.5 ±1.25 ±0.625Accuracy (% of FSR ±1LSB) 0.1 0.1 0.2 0.2 0.4

Analog Output (PCI-1712 only)Channels 2Resolution 12 bitsOutput Rate 1 MS/sFIFO Size 32,768 samplesOutput Range (V, software programmable)

Internal ReferenceBipolar ±5, ±10Unipolar 0 ~ 5, 0 ~ 10

External Reference 0 ~ +x V @ +x V (-10 ≤ x ≤ 10) -x ~ +x V @ +x V (-10 ≤ x ≤ 10)

Slew Rate 20 V/µsDriving Capability 10 mAOutput Impedance 0.1 W max.Operation Mode Software polling, continuous output and waveform

outputAccuracy INLE: ±1 LSB

DNLE: ±1 LSB (monotonic)

Digital InputChannels 16Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min.


Logic 1: 2.0 V min.Output Capability Sink: 8.0 mA @ 0.8 V

Source: -0.4 mA @ 2.0 V

Pacer/CounterChannels 3Resolution 16 bitsCompatibility 5 V/TTLMax. Input Frequency 10 MHzReference Clock Internal: 10 MHz, 1 MHz, 100 kHz, 10 kHz

External Frequency: 10 MHz max.

GeneralBus Type PCI V 2.2I/O Connector 1 x 68-pin SCSI female connectorDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: +5 V @ 850 mA, +12 V @ 600 mA

Max: +5 V @ 1.0 A, +12 V @ 700 mAOperating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)Storage Temperature -20 ~ 85° C (-4 ~ 185° F)Storage Humidity 5 ~ 95% RH non-condensing (refer to IEC 68-2-3)

PCI-1712/L

IntroductionPCI-1712 and PCI-1712L are powerful high-speed multifunction cards for the PCI bus. They feature a 1 MHz 12-bit A/D converter, an onboard FIFO buffer (storing up to 1024 samples for A/D, and up to 32,768 samples for D/A conversion). The PCI-1712 cards provide a total of up to 16 single-ended or 8 differential A/D input channels or a mixed combination, two 12-bit D/A output channels, 16 digital input/output channels, and three 10 MHz 16-bit multifunction counter channels. PCI-1712L is a low-cost version without analog output.

16 single-ended or 8 differential or a combination of analog inputs12-bit A/D converter, with up to 1 MHz sampling rateProgrammable gainAutomatic channel/gain scanningOnboard FIFO memory (AI: 1,024 samples AO: 32,768 samples)Two 12-bit analog output channels with continuous waveform output function (PCI-1712 only)16-ch digital input and 16-ch digital outputThree 16-bit programmable multifunction counter/timers on 10 MHzAuto-calibration (AI/AO)PCI-Bus mastering data transferPre-, post-, about- and delay-trigger data acquisition modes for analog input channelsFlexible triggering and clocking capabilities

1 MS/s, 12-bit, 16-ch PCI Multifunction Card


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



PCI-1712/L

Pin AssignmentsOrdering InformationPCI-1712 1 MS/s, 12-bit High-speed Multifunction PCI CardPCI-1712L 1 MS/s, 12-bit High-speed Multi. PCI Card w/o AOPCLD-8712 DIN-rail Wiring Board for PCI-1712/LPCL-10168-1 68-pin SCSI Shielded Cable, 1 mPCL-10168-2 68-pin SCSI Shielded Cable, 2 mADAM-3968 68-pin DIN-rail SCSI Wiring Board


Features



Channels 16 single-ended/ 8 differential (software programmable)Resolution 16 bitsMax. Sampling Rate 250 kS/sFIFO Size 1,024 samplesOvervoltage Protection 30 Vp-pInput Impedance 100 MW/10 pF (off), 100 MW/100 pF (on)Sampling Modes Software, onboard programmable pacer and externalInput Range (V, software programmable)


Analog Output (PCI-1716 only)Channels 2Resolution 16 bitsOutput Rate Static updateOutput Range (V, software programmable)

Internal ReferenceUnipolar 0 ~ 5 , 0 ~ 10Bipolar ±5, ±10

External Reference 0 ~ +x V @ +x V (-10 ≤ x ≤ 10) -x ~ +x V @ +x V (-10 ≤ x ≤ 10)

Slew Rate 20 V/µsDriving Capability 20 mAOutput Impedance 0.1 W max.Operation Mode Software pollingAccuracy INLE: ±1 LSB

Digital Input Channels 16Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min.



Source: -2.4 mA @ 2.0 V

Pacer/CounterChannels 1Resolution 16 bitsCompatibility 5 V/TTLMax. Input Frequency 1 MHzReference Clock Internal: 10 MHz

External Clock Frequency: 10 MHz max.

GeneralBus Type PCI V2.2I/O Connector 1 x 68-pin SCSI female connectorDimensions 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: +5 V @ 850 mA, +12 V @ 600 mA

Max.: +5 V @ 1 A, +12 V @ 700 mAOperating Temperature 0 ~ 70° C (32 ~ 158° F) (refer to IEC 68-2-1, 2)Storage Temperature -20 ~ 85° C (-4 ~ 185° F)Operating Humidity 5 ~ 85% RH non-condensing(refer to IEC 68-1, -2, -3)Storage Humidity 5 ~ 95% RH non-condensing (refer to IEC 68-1, -2, -3)

PCI-1716/L16 single-ended or 8 differential or a combination of analog inputs



Auto-calibration

PCI-Bus mastering data transfer

2 analog output channels (PCI-1716 only)



BoardID™ switch

IntroductionPCI-1716 and PCI-1716L are powerful high-resolution multifunction cards for the PCI bus. They feature a 250 kS/s 16-bit A/D converter, and an onboard 1,024-sample FIFO buffer for A/D. The cards have up to 16 single-ended or 8 differential A/D input channels or a combination of these; two 16-bit D/A output channels, 16 digital input/output channels, and one 10 MHz 16-bit counter channel. PCI-1716 and PCI-1716L provide specific functions for different user requirements.

250 kS/s, 16-bit, 16-ch PCI Multifunction Card


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



PCI-1716L

Ordering InformationPCI-1716 250 kS/s, 16-bit High-resolution Multi. CardPCI-1716L 250 kS/s, 16-bit High-res. Multi. Card w/o AOPCLD-8710 DIN-rail Wiring Board w/ CJCPCL-10168-1 68-pin SCSI Shielded Cable, 1 mPCL-10168-2 68-pin SCSI Shielded Cable, 2 mADAM-3968 68-pin DIN-rail SCSI Wiring Board

PCI-1716/L

Pin Assignments

PCI-1716L


Features


PCI-1718HDU


Channels 16 single-ended/8 differential (software programmable)Resolution 12 bitsMax. Sampling Rate 100 kS/sFIFO Size 1,024 samplesOvervoltage Protection 30 Vp-pInput Impedance 100 MWSampling Modes Software, onboard or external programmable pacerInput Range

PCI-1718HDU

Unipolar N/A 0 ~ 10 0 ~ 5 0 ~ 2.5 0 ~ 1.25Bipolar ±10 ±5 ±2.5 ±1.25 ±0.625Accuracy (% of FSR ±1LSB)

0.1 0.1 0.2 0.2 0.4

Analog OutputChannels 1Resolution 12 bitsOutput Rate Static updateOutput Range (V, software programmable)

Internal Reference Unipolar 0 ~ 5, 0 ~ 10External Reference 0 ~ x V @ x V (-10 ≤ x ≤ 10)

Slew Rate 10 V/µsDriving Capability 10 mAOutput Impedance 0.1 W max.Operation Mode Software pollingAccuracy INLE: ±1LSB

Digital InputChannels 16Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max., Logic 1: 2 V min.

IntroductionThe PCI-1718HDU and the PCL-818H series are 100 kS/s multifunction data acquisition cards that offer the five most desired measurement and control functions: 12-bit A/D conversion, 12-bit D/A conversion, digital input, digital output, and counter/timer. With 3-way compatibility, migration is possible from ISA bus to PCI bus.

ISA-Compatible with PCL-818HD

16-ch single-ended or 8-ch differential analog input


Programmable gain



One 12-bit analog output channel


Universal PCI bus (support 3.3 V or 5 V PCI bus signal)

BoardID™ switch



Source: -0.4 mA @ 2.0 V

Counter/TimerChannels 1 Resolution 16 bitsCompatibility 5 V/TTLMax. Input Frequency 10 MHzReference Clock Internal: 10 MHz

External Clock Frequency: 10 MHz

GeneralBus Type Universal PCI 2.2I/O Connector 1 x DB37 female connector

2 x 20-pin box headerDimensions 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: +5 V @ 850 mA

Max.: +5 V @ 1 AOperating Temperature 0 ~ 60 °C (32 ~ 140 °F)Storage Temperature -20 ~ 70 °C (-4 ~ 158 °F)Operating Humidity 5 ~ 85% RH non-condensing (refer to IEC 68-1, -2, -3)Storage Humidity 5 ~ 95% RH non-condensing (refer to IEC 68-1, -2, -3)Certifications CE

100 kS/s, 12-bit, 16-ch Universal PCI Multifunction Card


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Ordering InformationPCI-1718HDU 100 kS/s, 12-bit, 16-ch Univ. PCI Multi. CardPCL-10120-1 20-pin Flat Cable, 1 mPCL-10120-2 20-pin Flat Cable, 2 mPCL-10137-1 DB37 Cable, 1 mPCL-10137-2 DB37 Cable, 2 mPCL-10137-3 DB37 Cable, 3 mPCLD-8115 Wiring Board w/ CJC Circuit & One DB37 CablePCLD-880 Wiring Board w/ Two 20-pin Flat Cables & Adapter

PCI-1718HDU

34

18

5678

101112131415

9

1617

1

19

22223

37

24252627

293031323334

28

3536

2021

A/D S2A/D S3

Counter 0 OUT

A/D S4A/D S5A/D S6A/D S7

A.GNDV.REFS0*+12 VS2*

D.GND

A.GND

NCCounter 0 CLK

A/D S0

+5V

A/D S1A/D S10A/D S11

Counter 0 GATE

A/D S12A/D S13A/D S14A/D S15

A.GNDDA0.OUTDA0.VREF

S1*S3*

D.GND

A.GND

EXT.TRIG

A/D S8

PACER

A/D S9

Pin Assignments


Features

PCI-1742UPCI-1741U

PCI-1741UPCI-1742U


Channels 16 single-ended/8 differential (software programmable)Resolution 16 bitsMax. Sampling Rate PCI-1741U: 200 kS/s

PCI-1742U: single-channel - 1 MS/s multi-channel - 800 kS/s unipolar bipolar mixed - 250 kS/s

FIFO Size 1,024 samplesOvervoltage Protection 20 Vp-pInput Impedance 100 MW/10pF (Off); 100 MW/100pF (On)Sampling Mode Software, onboard programmable pacer and externalInput Range* (V, software programmable)


* Note: All channels should be set to the same range

Analog OutputChannels PCI-1741U: 1

PCI-1742U: 2Resolution 16 bitsOutput Rate Static updateOutput Range (V, software programmable)

Internal Reference

Bipolar ±5, ±10Unipolar 0 ~ 5, 0 ~ 10

External Reference 0 ~ +xV @ +xV (-10 ≤ x ≤ 10) -x ~ +xV @ +xV (-10 ≤ x ≤ 10)

Slew Rate PCI-1741U: 20 V/us PCI-1742U: 40 V/us

Driving Capability ±20 mAOutput Impedance 0.1 W max.Operation Mode Software polling

IntroductionPCI-1741U and PCI-1742U are powerful high-resolution multifunction data acquisition cards supporting universal PCI bus. The sampling rate is up to 1 MS/s (PCI-1742U) or 200 kS/s (PCI-1741U). Coupled with the 16-bit A/D converter, they are suitable for most data acquisition applications. PCI-1741U and PCI-1742U provides 16 single-ended or 8 differential analog input channels and 16 digital input/output channels. PCI-1741U provides one 16-bit D/A output channel, while PCI-1742U provides two 16-bit D/A output channels.

200 kS/s, 16-bit, 16-ch Universal PCI Multifunction Card1 MS/s, 16-bit, 16-ch Universal PCI Multifunction Card


PCI-1741U: 16-bit A/D converter, with up to 200 kHz sampling rate PCI-1742U: 16-bit A/D converter, with up to 1 MHz sampling rate


Auto calibration

PCI-1741U: 1 x 16-bit analog output channel PCI-1742U: 2 x 16-bit analog output channels


Universal PCI bus (support 3.3 V or 5 V PCI bus signal)


BoardID™ switch

Accuracy INLE: ±2LSB

Digital Input Channels 16Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min.


Logic 1: 2.0 V min.Output Capability Sink: 24 mA @ 0.8 V

Source: -15 mA @ 2.0 V

Counter/TimerChannels 1Compatibility 5 V/TTLResolution 16 bitsMax. Input Frequency 10 MHzReference Clock Internal: 10 MHz

External Clock Frequency: 10 MHz

GeneralBus Type Universal PCI 2.2I/O Connector Type 1 x 68-pin SCSI female connectorDimensions 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: +5 V @ 850 mA, +12 V @ 600 mA

Max.: +5 V @ 1 A, +12 V @ 700 m AOperating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)Certifications CE



8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Ordering InformationPCI-1741U 200 kS/s, 16-bit, 16-ch Univ. PCI Multi. CardPCI-1742U 1 MS/s, 16-bit, 16-ch Univ. PCI Multi. CardPCL-10168-1 68-pin SCSI Shielded Cable, 1 mPCL-10168-2 68-pin SCSI Shielded Cable, 2 mADAM-3968 68-pin DIN-rail SCSI Wiring BoardPCLD-8710 DIN-rail Wiring Board w/ CJC

Pin Assignments

PCI-1741UPCI-1742U

PCI-1742U

PCI-1741U PCI-1742U

PCI-1742U

N/A

N/A

N/A


Features



Channels 8 single-endedResolution 12 bitsMax. Sampling Rate 40 kS/sFIFO Size 0Overvoltage Protection 30 Vp-pInput Impedance >10 MWSampling Modes Software, pacer or external triggerInput Range (V) ±5, ±2.5, ±1.25, ±0.625, ±0.3125Accuracy ±2 LSB

Analog OutputChannels 1 double-bufferedResolution 12 bitsOutput Rate Static updateOutput Range 0 ~ 5 V or 0 ~ 10 VDriving Capability 5 mA

Digital InputChannels 16Compatibility 5 V/TTLInput Voltage Logic 0: 0.8V max.

Logic 1: 2.0V min.

40 kS/s, 12-bit, 8-ch ISA Multifunction CardPCL-711B



Programmable gain



Screw-terminal board and cable included


Logic 1: 2.0 V min.Output Capability Sink: 8 mA

Source: 0.4 mA

GeneralBus Type ISAI/O Connectors 3 x 20-pin box headerDimensions (L x H) 155 x 100 mm (6.1" x 3.9")Power Consumption +5 V @ 500 mA typical, 1.0 A max.

+12 V @ 50 mA typical, 100 mA max. -12 V @ 14 mA typical, 20 mA max.

Operating Temperature 0 ~ 50° C (32 ~ 122° F)Storage Temperature -20 ~ 65° C (-4 ~ 149° F)Storage Humidity 5 ~ 95% RH non-condensing (refer to IEC 68-2-3)Certifications CE

Ordering InformationPCL-711B 40 kS/s, 12-bit, 8-ch ISA Multifunction CardPCL-10120-1 20-pin Flat Cable, 1 mPCL-10120-2 20-pin Flat Cable, 2 m

IntroductionPCL-711B offers four of the most popular I/O functions for PC and compatible systems: A/D conversion, D/A conversion, digital input and digital output. The inexpensive PCL-711B is ideal for entry level applications. The features of this half-sized card include: eight 12-bit analog inputs, one 12-bit analog output, 16 digital inputs and 16 digital outputs. In addition, it comes with a 20-point screw-terminal board and a flat cable connector. PCL-711B performs a variety of I/O jobs, and features solid software support and a large selection of available daughterboards and accessories. It is an ideal and affordable performer for OEMs, schools and hobbyists who require a combination of analog and digital I/O.


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features



Channels 16 single-endedResolution 12 bitsMax. Sampling Rate 30 kS/sFIFO Size 0Overvoltage Protection 30 Vp-pInput Impedance >10 MWSampling Modes Software, pacer or external triggerInput Range (V, software programmable)

±10, ±5, ±2.5, ±1.25, ±0.625, ±0.3125Accuracy 0.4% of reading ±1 LSB

Analog OutputChannels 2 double-bufferedResolution 12 bitsOutput Rate Software pollingOutput Range (V, software programmable)

Internal Reference Unipolar 0 ~ 5, 0 ~ 10External Reference ±10 max.

Driving Capability 5 mA

Digital InputChannels 16Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V

Logic 1: 2.0 V

30 kS/s, 12-bit, 16-ch ISA Multifunction Card PCL-812PG



Programmable gain

Two 12-bit analog output channels



A/D with DMA or interrupt

Digital OutputChannels 16Compatibility 5 V/TTLOutput Voltage Logic 0: 0.5 V max., Logic 1: 2.4 V min.Output Capacity Sink: 8.0 mA, Source: 0.4 mA

Counter/TimerChannels 1 Resolution 16 bits Compatibility 5 V/TTL Max. Input Frequency 500 kHzReference Clock Internal: 2 MHz

External Frequency: 10 MHz External Voltage Range: 5V/TTL

GeneralBus Type ISAI/O Connectors 5 x 20-pin box headerDimensions (L x H) 185 x 100 mm (7.3" x 3.9")Power Consumption +5 V @ 500 mA typical, 1.0 A max.

+12 V @ 50 mA typical, 100 mA max.Operating Temperature 0 ~ 50° C (32 ~ 122° F)Storage Temperature -20 ~ 65° C (-4 ~ 149° F)Storage Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)

Ordering InformationPCL-812PG 30 kS/s, 12-bit, 16-ch ISA Multifunction CardPCL-10120-1 20-pin Flat Cable, 1 mPCL-10120-2 20-pin Flat Cable, 2 mPCLD-780 Screw Terminal Board w/ Two 20-pin Flat Cables

IntroductionPCL-812PG is a multifunction analog and digital I/O card that features the five most desired measurement and control functions for PC/AT and compatible systems: A/D conversion, D/A conversion, digital input, digital output and counter/timer. This half-size card neatly packages 16 12-bit analog input channels, two 12-bit analog output channels, 16 digital input channels, 16 digital output channels and a programmable counter/timer.

In addition to all the features listed above, PCL-812PG offers the convenience of programmable analog input ranges, where the analog input range can be switched by software commands instead of DIP switches. PCL-812PG also delivers convenience and maximum resolution for applications that need different gains for different channels or different gains for different stages of a process. Comprehensive software support, numerous I/O options and a wide range of available daughterboards make the PCL-812PG ideal for industrial applications that require a combination of analog and digital I/O.


Features


100 kS/s, 12-bit, 16-ch ISA Multifunction Card40 kS/s, 12-bit, 16-ch ISA Multifunction Card


Channels 16 single-ended / 8 differentialResolution 12 bitsMax. Sampling Rate 100 kS/s for all input ranges (PCL-818HD/HG only)

40 kS/s for all input ranges (PCL-818L only)FIFO Size 1,024 samplesOvervoltage Protection 30 Vp-pInput Impedance 10 MWSampling Modes Software, pacer or externalInput Range (V, software programmable)

PCL-818L/818HDBipolar ±10 ±5 ±2.5 ±1.25 ±0.625Unipolar* N/A 0 ~ 10 0 ~ 5 0 ~ 2.5 0 ~ 1.25Accuracy (% of FSR ±1LSB) 0.1 0.1 0.2 0.2 0.4

* Note: PCL-818L doesn’t support unipolar input range.

PCL-818HGBipolar ±10 ±5 ±1 ±0.5 ±0.1 ±0.05 ±0.01 ±0.005Unipolar N/A 0 ~ 10 N/A 0 ~ 1 N/A 0 ~ 0.1 N/A 0 ~ 0.01Accuracy (% of FSR ±1LSB) 0.1 0.1 0.2 0.2 0.4 0.4 0.8 0.8

Analog OutputChannels 1Resolution 12 bitsOutput Rate Static updateOutput Range (V, software programmable)

Internal Reference Unipolar 0 ~ 5, 0 ~ 10External Reference 0 ~ 10, 0 ~ -10



Programmable gain


Onboard FIFO memory (1,024 samples, PCL-818HD/HG only)




Digital InputChannels 16Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min.



Source: -0.4 mA

Timer/CounterChannels 1A/D Pacer 32-bit with 10 MHz or 1 MHz time baseMax. and Min. Rates 2.5 MHz and 0.00023 HzCounter One 16-bit counter with 100 kHz time base

GeneralPower Consumption +5 V @ 210 mA typical, 500 mA max.

+12 V @ 20 mA typical, 100 mA max. -12 V @ 20 mA typical, 40 mA max.

I/O Connector 1 x DB37 female 2 x 20-pin box header

Dimensions (L x H) 155 x 100 mm (6.1" x 3.9")Operating Temperature 0 ~ 50° C (32 ~ 122° F)Storage Temperature -20 ~ 65° C (-4 ~ 149° F)Operating Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)

IntroductionThe PCL-818L series was designed for entry-level models to the PCL-818 series. The cards have been designed with the cost-sensitive customer in mind, but still offers the same functions as the rest of the series, except that they have a 40 kHz sampling rate and only accepts bipolar inputs. They are fully software and connector compatible with the PCL-818HD and PCL-818HG. This lets you upgrade your applications to these higher performance cards without hardware or software changes.

The PCL-818LS bundle consists of the PCL-818L card, the PCLD-8115 wiring terminal board and a DB37 cable assembly. The PCLD-8115 accommodates onboard passive signal conditioning components (resistors and capacitors), allowing you to easily implement a low-pass filter, a voltage attenuator or a 4 ~ 20 mA voltage converter.

PCL-818HD/HGPCL-818L


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Ordering Information PCL-818HD High-performance Half-size Multifunction CardPCL-818HG High-performance and High-gain Multi. CardPCL-818L Low-cost High-perform. Half-size Multi. CardPCL-818LS PCL-818L w/ PCLD-8115 and DB37 CablePCL-10137-1 DB37 Cable, 1 mPCL-10137-2 DB37 Cable, 2 mPCL-10137-3 DB37 Cable, 3 mPCLD-8115 Wiring Board w/ CJC Circuit & One DB37 CablePCLD-880 Wiring Board w/ Two 20-pin Flat Cables & Adapter

PCL-818HD/HGPCL-818L

Pin Assignments


Features



Channels 32 single-ended/16 differential (software programmable)

Resolution 12 bitsMax. Sampling Rate 100 kS/sFIFO Size 4,096 samplesOvervoltage Protection 30 Vp-pIsolation Protection 2,500 VDC

Input Impedance 1 GWSampling Modes Software, onboard programmable pacer and external

(TTL level)Input Range (V, software programmable)

Unipolar N/A 0 ~10 0 ~ 5 0 ~ 2.5 0 ~ 1.25Bipolar ±10 ±5 ±2.5 ±1.25 ±0.625Accuracy (% of FSR ±1LSB) 0.1 0.1 0.2 0.2 0.4

GeneralBus Type PCI V2.2I/O Connector 1 x DB37 female connectorDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: +5 V @ 850 mA

Max: +5 V @ 1.0 AOperating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95% RH non-condensing (refer to IEC 68-2-3)

PCI-17132,500 VDC isolation protection



Programmable gain


Isolation protection (2,500 VDC)

S/W, internal or external pacer sampling modes supported

100 kS/s, 12-bit, 32-ch Isolated Analog Input PCI Card

Ordering InformationPCI-1713 100 kS/s, 12-bit, 32-ch Isolated AI PCI CardPCLD-881B Wiring Board for PCI-1713, PCI-1715U & PCL-813BADAM-3937 DB37 DIN-rail Wiring BoardPCL-10137-1 DB37 Cable, 1 mPCL-10137-2 DB37 Cable, 2 mPCL-10137-3 DB37 Cable, 3 m

Pin Assignments

IntroductionThe PCI-1713 is an isolated high-speed analog input card for the PCI bus. It provides 32 analog input channels with a sampling rate up to 100 kS/s, 12-bit resolution and isolation protection of 2,500 VDC.


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features


PCI-1715U 500 kS/s, 12-bit, 32-ch Isolated Analog Input Universal PCI Card

2,500 VDC isolation protection


12-bit resolution for A/D conversion

Up to 500 kS/s sampling rate for A/D conversion

Programmable gain for each input channel

Onboard 1,024 samples FIFO buffer

S/W, internal or external pacer sampling modes supported

Universal PCI Bus

BoardID™ switch


Channels 32 single-ended/16 differential (software programmable)

Resolution 12 bitsMax. Sampling Rate 500 kS/sFIFO Size 1,024 samplesOvervoltage Protection 30 Vp-pIsolation Protection 2,500 VDC

Input Impedance 1 GWSampling Modes Software, onboard programmable pacer and external

(TTL level)Input Range (V, software programmable)

Unipolar N/A 0 ~10 0 ~ 5 0 ~ 2.5 0 ~ 1.25Bipolar ±10 ±5 ±2.5 ±1.25 ±0.625Accuracy (% of FSR ±1LSB) 0.1 0.1 0.2 0.2 0.4

GeneralBus Type Universal PCI V2.2I/O Connector 1 x DB37 female connectorDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: +5 V @ 850 mA

Max: +5 V @ 1.0 AOperating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95% RH non-condensing (refer to IEC 68-2-3)

Ordering InformationPCI-1715U 500 kS/s 12-bit, 32-ch Isolated AI PCI CardPCLD-881B Wiring Board for PCI-1713, PCI-1715U & PCL-813BADAM-3937 DB37 DIN-rail Wiring BoardPCL-10137-1 DB37 Cable, 1 mPCL-10137-2 DB37 Cable, 2 mPCL-10137-3 DB37 Cable, 3 m

Pin Assignments

IntroductionThe PCI-1715U is an isolated high-speed analog input card for the PCI bus. It provides 32 analog input channels with a sampling rate up to 500 kS/s, 12-bit resolution and isolation protection of 2,500 VDC.


Features



Channels 4 single-endedResolution 12 bitsMax. Sampling Rate PCI-1741U: 30 MS/s

PCI-1741UL: 10 MS/sFIFO Size PCI-1714U: 32,768 samples for each channel

PCI-1714UL: 8,192 samples for each channelOvervoltage Protection 30 Vp-pInput Impedance 50 W/1 MW/Hi Z jumper selectable/100 pFSampling Modes Software polling, pacerTrigger Modes Post-trigger, pre-trigger, delay-trigger, about-triggerInput Range (V) ±5, ±2.5, ±1, ±0.5

GeneralBus Type Universal PCI V2.2I/O Connectors 4 x BNC connector (for AI)

1 x PS/2 connector (for Ext. clock and trigger)Dimensions 175 x 100mm (6.9" x 3.9")Power Consumption Typical: +5 V @ 850 mA ; +12 V @ 600 mA

Max.: +5 V @ 1 A; +12 V @ 700m AOperating Temperature 0 ~ 70° C (32 ~ 158° F)Storage Temperature -20 ~ 85° C (-4 ~ 185° F)Storage Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)Certifications CE

PCI-1714UPCI-1714UL

4 single-ended analog input channels

12-bit A/D converter, with up to 30 MHz sampling rate

Programmable gain

Onboard FIFO memory (PCI-1714U: 32,768 samples PCI-1714UL: 8,192 samples, each channel)

4 A/D converters simultaneously sampling

Multiple A/D triggering modes

Programmable pacer/counter

BoardID™ switch

Universal PCI Bus (support 3.3 V or 5 V PCI bus signal)

30 MS/s, 12-bit, Simultaneous 4-ch Analog Input Universal PCI Card10 MS/s, 12-bit, Simultaneous 4-ch Analog Input Universal PCI Card

PS/2PS/2

Ordering InformationPCI-1714U 30 MS/s, 12-bit, Simultaneous 4-ch AI PCI CardPCI-1714UL 10 MS/s, 12-bit, Simultaneous 4-ch AI PCI CardADAM-3909 DB9 DIN-rail Wiring BoardPCL-1010B-1 BNC to BNC Wiring Cable, 1 mPCL-10901-1 PS/2 to DB9 Cable, 1 mPCL-10901-3 PS/2 to DB9 Cable, 3 m

Pin Assignments

IntroductionPCI-1714U is an advanced high-performance data acquisition card based on the PCI bus. With a large FIFO of 32,768 for each channel, the maximum sampling rate of PCI-1714U can get up to 30 MS/s, on each channel, with an emphasis on continuous, non-stop, high-speed, streaming data of samples to host memory. The low-cost PCI-1714UL offers 10MS/s on each channel at a stable rate, and has also been equipped with a universal PCI interface.


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features


PCI-1747U


Channels 64 single-ended, 32 differential, or combinationResolution 16 bitsMax. Sampling Rate 250 kS/sFIFO Size 1,024 samplesOvervoltage Protection 20 Vp-pInput Impedance 100 MW/10 pF (Off); 100 MW/100 pF (On)Sampling Modes Software and onboard programmable pacer Input Range (V, software programmable)


GeneralBus Type Universal PCI V2.2I/O Connector 1 x 68-pin SCSI female connectorDimensions 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: +5 V @ 850 mA, +12 V @ 600 mA

Max: +5 V @ 1 A, +12 V @ 700 m AOperating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)Certifications CE

IntroductionPCI-1747U is a high-resolution, high-channel-count analog input card for the PCI bus. Its sampling rate is up to 250 kS/s and 16-bit resolution provides the resolution needed for most data acquisition applications. PCI-1747U provides 64 single-ended, 32 differential analog input channels or a combination of these. It also has built in a 1,024 FIFO buffer for analog input data.



Auto calibration


PCI-Bus mastering data transfer

Universal PCI Bus (support 3.3 V or 5 V PCI bus signal)

BoardID™ switch

250 kS/s, 16-bit, 64-ch Analog Input Universal PCI Card

Ordering InformationPCI-1747U 250 kS/s, 16-bit, 64-ch AI Universal PCI CardADAM-3968 68-pin DIN-rail SCSI Wiring BoardPCL-10168-1 68-pin SCSI Shielded Cable, 1 mPCL-10168-2 68-pin SCSI Shielded Cable, 2 m

Pin Assignments


Features



Channels 32 single-ended Resolution 12 bitsMax. Sampling Rate 25 kHz Overvoltage Protection 30 Vp-pIsolation Protection 500 VDC from analog input to PCInput Impedance > 10 MWSampling Modes software triggerInput Range (V, software programmable)

Unipolar (jumper selection) 0 ~ 10 0 ~ 5 0 ~ 2.5 0 ~ 1.25Bipolar (software selection) ±5 ±2.5 ±1.25 ±0.625Accuracy (% of FSR ±1LSB) 0.1 0.2 0.2 0.4

GeneralBus Type ISAI/O Connectors 1 x DB37 female connectorDimensions (L x H) 219 x 100 mm (8.6" x 3.9")Power Consumption +5 V @ 660 mA max.

+12 V @ 140 mA max.Operating Temperature 0 ~ 50° C (32 ~ 122° F)Storage Temperature -20 ~ 65° C (-4 ~ 149° F)Storage Humidity 5 ~ 95% RH non-condensing (refer to IEC 68-2-3)

PCL-813B 25 kS/s, 12-bit, 32-ch Isolated Analog Input ISA Card

32 single-ended analog input channels


Isolation protection (500 VDC)

Program-controlled A/D trigger and data transfer

Ordering InformationPCL-813B 25 kS/s, 12-bit, 32-ch Isolated AI ISA CardPCLD-881B Wiring Board for PCI-1713, PCI-1715U & PCL-813BPCL-10137-1 DB37 Cable, 1 mPCL-10137-2 DB37 Cable, 2 mPCL-10137-3 DB37 Cable, 3 mADAM-3937 DB37 DIN-rail Wiring Board

IntroductionPCL-813B is a 12-bit 32-channel analog input card that offers high-voltage isolation on each analog input. It is an extremely cost effective solution for applications in industrial measurement and monitoring. The card offers 32 analog input channels with software programmable gain on each channel and two DC-to-DC converters on a 4-layer PCB with an integral ground plane. Optically-isolated inputs provide over 500 VDC of isolation between the analog inputs and the PC, protecting the PC and peripherals from damage due to high voltages on the input lines. PCL-813B is ideal for situations where the budget-conscious user requires flexibility, stability and a high level of isolation protection. PCL-813B comes with the PCLD-881B wiring terminal board and a DB-37 cable assembly.

Typical application for PCL-813B:

Industrial 4 ~ 20 mA Output Device Monitoring


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features


Ordering InformationPCI-1720U 12-bit, 4-ch Isolated AO Universal PCI CardPCL-10137-1 DB37 Cable, 1 mPCL-10137-2 DB37 Cable, 2 mPCL-10137-3 DB37 Cable, 3 mADAM-3937 DB37 DIN-rail Wiring BoardPCLD-880 Wiring Board w/ Two 20-pin Flat Cables & Adapter

Pin Assignments

PCI-1720U

SpecificationsAnalog Output

Channels 4 isolatedResolution 12 bitsOutput Rate Static updateOutput Range (Software programmable)

Internal ReferenceUnipolar (V) 0 ~ 5, 0 ~ 10Bipolar (V) ±5, ±10Current Loop (mA) 0~ 20, 4 ~ 20

Slew Rate 2 V/µsIsolation Protection 2,500 VDC

Driving Capability 5 mAOperation Modes Software pollingAccuracy ±0.024%Excitation Voltage 50 V (max.)

General Bus Type Universal PCI 2.2I/O Connectors 1 x DB37 female connectorDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption +5 V @ 350 mA (typical), 500 mA (max.)

+12 V @ 200 mA (typical), 350 mA (max.)Operating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)Storage Temperature -20 ~ +70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)Certifications CE

12-bit, 4-ch Isolated Analog Output Universal PCI Card

4 x 12-bit D/A output channels

Multiple output ranges

2,500 VDC isolation between the outputs and the PCI bus

Keeps the output settings and values after system reset

One DB37 connector for easy wiring

Universal PCI and BoardID™ switch

IntroductionThe PCI-1720U provides four 12-bit isolated digital-to-analog outputs for the Universal PCI bus. With isolation protection of 2500 VDC between the outputs and the PCI bus, the PCI-1720U is ideal for industrial applications where high-voltage protection is required.


Features



Channels 4Resolution 12 bitsFIFO Size 1,024 samplesOutput Rate 10 MHz or static updateReference Clock Internal: 10 MHz

External Clock Frequency: 10 MHz max. External Voltage Range: 0.8 V max., 2 V min.

Output Range (Software programmable)

Internal ReferenceUnipolar 0 ~ 5 V, 0 ~ 10 V, Bipolar ±5 V, ±10 VCurrent Loop 0 ~ 20 mA, 4 ~ 20 mA

External Reference0 ~ +x V @ +x V (-10 ≤ x ≤ 10)-x ~ +x V @ +x V (-10 ≤ x ≤ 10)

Slew Rate 10 V/µsDriving Capability 10 mAOutput Impedance 0.1 W max.Operation Modes Single/continuous/waveform/synchronized outputAccuracy Relative: ±1 LSB

Differential Non-linearity: ±1 LSB (monotonic)

Digital Input/OutputChannels 16 (shared by input/output)Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min.Output Capability Sink: 0.5 V @ 24 mA

Source: 2.0 V @ -15 mA

PCI-172110 MHz maximum digital update rate

PCI-bus mastering for data transfer

Auto calibration function

Four analog output channels with 1,024 samples FIFO buffer

A 12-bit DAC is equipped for each of analog output channels

Real-time waveform output function with internal/external pacer

Synchronized output function

Flexible output types and range settings

Keeps the output settings and values after system hot reset

16-ch DI/O and one 10 MHz 16-bit resolution counter

BoardID™ switch

IntroductionPCI-1721 is an advanced high-speed analog output card for the PCI bus, and each of analog output channels are equipped with a 12-bit, double-buffered DAC. It features many powerful and unique functions, like a waveform output function with 10 MHz maximum update rate, auto-calibration and a BoardID switch. PCI-1721 is an ideal solution for industrial applications where high-speed continuous analog output or real-time waveform output functions are required.

12-bit, 4-ch Analog Output PCI Card with 16-ch Digital I/O

Counter/TimerChannels 1Resolution 16 bitsCompatibility 5 V/TTLMax. Input Frequency 10 MHzReference Clock Internal: 10 MHz

External Clock Frequency: 10 MHz max. External Voltage Range: 0.8 V max, 2.0 V min.

GeneralBus Type PCI V2.2I/O Connectors 1 x 68-pin SCSI female connectorDimensions 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: +5 V @ 850 mA, +12 V @ 600 mA

Max.: +5 V @ 1 A, +12 V @ 700 mAOperating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)Storage Temperature -20 ~ 85° C (-4 ~ 185° F)Storage Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)Certifications FCC, CE

Ordering InformationPCI-1721 12-bit, 4-ch Advanced PCI Analog Output CardPCL-10168-1 68-pin SCSI Shielded Cable, 1 mPCL-10168-2 68-pin SCSI Shielded Cable, 2 mADAM-3968 68-pin DIN-rail SCSI Wiring Board


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features


Ordering InformationPCI-1723 16-bit, 8-ch Non-isolated Analog Output PCI CardPCL-10168-1 68-pin SCSI Shielded Cable, 1 mPCL-10168-2 68-pin SCSI Shielded Cable, 2 mADAM-3968 68-pin DIN-rail SCSI Wiring Board

Pin Assignments

Auto calibration function

A 16-bit DAC is equipped for each analog output channel



2-port (16-channel) user-defined digital input/output channels

BoardID™ switch

PCI-1723

IntroductionPCI-1723 is a non-isolated multiple channel analog output card for the PCI bus, and each analog output channel is equipped with a 16-bit, double-buffered DAC. It also features an auto-calibration function and a BoardID™ switch. The PCI-1723 is an ideal solution for industrial applications where multiple analog output channels are required.

16-bit, 8-ch Analog Output PCI Card with 16-ch Digital I/O


Channels 8Resolution 16 bitsOutput Rate Static updateOutput Range (Software programmable)

Internal ReferenceBipolar (V) ±10Current Loop (mA) 0 ~ 20, 4 ~ 20

Driving Capability 5 mAOutput Impedance 0.1 W max.Operation Modes Software polling, synchronized outputAccuracy Relative: ±6 LSB

Differential Non-linearity: ±6 LSB (monotonic)

Digital Input/OutputChannels 16 (shared by input/output)Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.


Source: 2.0 V @ -15 mA

GeneralBus Type PCI V2.2I/O Connectors 1 x 68-pin SCSI female connectorDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: +5 V @ 850 mA, +12 V @ 600 mA

Max.: +5 V @ 1 A, +12 V @ 700 mAOperating Temperature 0 ~ 60° C (32 ~ 158° F) (IEC 68-2-1, 2)Storage Temperature -20 ~ 85° C (-4 ~ 185° F)Storage Humidity 5 ~ 95 % RH non-condensing (IEC 68-2-3)Certifications CE


Features


PCI-1724U 14-bit, 32-ch Isolated Analog Output Universal PCI Card

32 high-density analog output channels

Flexible Output Range: +/-10 V, 0 ~ 20 mA and 4 ~ 20 mA



BoardID™ switch

Pin AssignmentsSpecificationsAnalog Output

Channels 32 isolatedResolution 14 bitsOutput Rate Static updateOutput Range (Software programmable)

Internal ReferenceBipolar (V) ±10Current Loop (mA) 0 ~ 20, 4 ~ 20

Isolation Protection 1,500 VDC system isolationOutput Impedance 0.1 W max.Operation Modes Software polling, synchronized outputAccuracy Relative: ±4 LSB

Differential Non-linearity: ±2 LSB (monotonic)Driving Capacity 10 mA

GeneralBus Type Universal PCI V2.2I/O Connectors 1 x DB62 female connectorDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption +5 V @ 400 mA, +12 V @ 270 mA max.Operating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95 % RH, non-condensing (refer to IEC 68-2-3)

Ordering InformationPCI-1724U 14-bit, 32-ch Isolated AO Universal PCI CardPCL-10162-1 DB62 Cable, 1 mPCL-10162-3 DB62 Cable, 3 mADAM-3962 DB62 DIN-rail Wiring Board

57

30

35

AGND

AGND

2

AO4

AO14

26

16

53

59

45

AO10

5231

60

36

AGND 38

15

AGND

62

AO18

42

AGND

56

AO17

AGND 24

AGND

AO19

11

AO7

47

AGND

AO25

AO9

39

25

AGND

21

AO22

AGND

7

AGND

13

46

58

48

AO24

43

AGND

AO12

221

6

9

AGND

41

8

NC

AO31

27

AGND

55AO21

20

51

AGND

AO2

AGND

AO5

AO0

37

5AGND

NC

AO23

19

34

AO1

AO20

23

AGND

49

AO16

50

54AGND

AGND

AGND

12

3210

44

AO30

AO11

AGND

14

3

28

AO29

61

AO6

29

33

40

AGND

AO15

AGND

AGND

AO26

17

4

AO28AGND

AGND

AO3

AO13

AGND

18

AO27

AO8

IntroductionPCI-1724U is an isolated high-density multiple channel analog output card for the PCI bus, where each analog output channel is equipped with a 14-bit DAC. It feaures optional voltages, current output and a BoardID™ switch. PCI-1724U is an ideal solution for industrial applications where multiple analog output channels are required.


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features


PCL-727 12-bit, 12-ch Analog Output ISA Card with 32-ch Digital I/O


Channels 12Resolution 12 bitsOutput Rate Static outputOutput Range (Software programmable)

Bipolar (V) ±5Unipolar (V) 0 ~ 5, 0 ~10Current Loop (mA) 4 ~ 20

Driving Capability 15 mAOperation Modes Software polling, synchronized outputCurrent Loop 8 ~ 36 V Excitation Voltage

Digital InputChannels 16 Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min.Input loading 0.5 V @ 0.4 mA max. (low)

2.7 V @ 50 µA max (high)

Digital OutputChannels 16 Compatibility 5 V/TTLOutput Voltage Logic 0: 0.5 V, Logic 1: 2.4 VOutput Capability Sink: 0.8 mA @ 0.5 V

Source: 0.4 mA @ 2.4 V

GeneralBus Type ISAI/O Connectors 1 x DB37 female connector

2 x 20-pin box headerPower Consumption +5 V @ 500 mA typical, 1A max.

+12 V @50 mA typical, 110 mA max. -12 V @ 14 mA typical, 90 mA max.

Dimensions (L x H) 340 x 100 mm (13.4" x 3.9")Operating Temperature 0 ~ 50° C (32 ~ 122° F)Storage Temperature 0 ~ 65° C (32 ~ 149° F)Storage Humidity 5 ~ 95% RH, non-condensing

Ordering InformationPCL-727 12-bit, 12-ch AO ISA Card w/ Digital I/OPCL-10120-1 20-pin Flat Cable, 1 mPCL-10120-2 20-pin Flat Cable, 2 mPCL-10137-1 DB37 Cable, 1 mPCL-10137-2 DB37 Cable, 2 mPCL-10137-3 DB37 Cable, 3 mADAM-3937 DB37 DIN-rail Wiring BoardPCLD-780 Screw Terminal Board w/ Two 20-pin Flat CablesPCLD-782 16-ch Isolated DI Board w/ 1m 20-pin Flat CablePCLD-785 16-ch Relay Board w/ One 1m 20-pin Flat Cable

12 independent analog output channels

Fuse on each channel

BoardID™ switch


IntroductionThe PCL-727 provides 12 analog output channels on a full-size add-on card. In additional to its analog output, the PCL-727 provides 16 digital output channels and 16 digital output channels. It is an ideal and economical solution for industrial applications that requires multiple analog and/or current output channels.


Features



Channels PCL-726: 6 PCL-728: 2 isolated

Resolution 12 bits, double bufferedOutput Rate Static updateReference Voltage Internal: -5 V (±0.05 V)

-10 V (±0.05 V) External: DC or AC, ±10V max.

Output Range (Software programmable)

Internal ReferenceBipolar (V) ±5Unipolar (V) 0 ~ 5, 0 ~10Current Loop (mA) 4 ~ 20

External Reference Bipolar (V) ±10

Isolation Protection 500 VDC (PCL-728)Driving Capability 5 mA Output Impedance 0.1 WOperation Modes Software pollingAccuracy 0.012% Excitation Voltage 8 ~ 36 V for 4 ~ 20 mA current loop

Digital Input (PCL-726)Channels 16Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min.

Digital Output (PCL-726)Channels 16Compatibility 5 V/TTLOutput Voltage Logic 0: 0.5 V, Logic 1: 2.4 VOutput Capability Sink: 0.5 V @ 0.4 mA max.

Source: 2.7 V @ 50 mA max.

PCL-726PCL-728

12-bit, 6-ch Analog Output ISA Card with 32-ch Digital I/O12-bit, 2-ch Isolated Analog Output ISA Card

Independent analog output channels

12-bit resolution double-buffered D/A converter

Multiple voltage ranges: ±10 V, ±5 V, 0 ~ +5 V, 0 ~ +10 V and 4 ~ 20 mA current loop (sink)

16 digital input and 16 digital output channels (PCL-726)

Two DB9 connectors for easy wiring (PCL-728)

GeneralBus Type ISAI/O Connectors PCL-726: 4 x 20-pin box header

PCL-728: 2 x DB9 female connector Dimensions (L x H) PCL-726: 340 x 100 mm (13.4" x 3.9")

PCL-728: 184 x 119 mm (7.25" x 4.7")Power Consumption

PCI-726: +5 V @ 500 mA typical, 1 A max. +12 V @ 80 mA typical, 110 mA max. -12 V @ 60 mA typical, 90 mA max. PCL-728: +5V @ 800 mA max.

Operating Temperature 0 ~ 50° C (32 ~ 122° F)Storage Temperature 0 ~ 65° C (32 ~ 149° F)Operating Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)

Ordering InformationPCL-726 12-bit, 6-ch AO ISA Card w/ Digital I/OPCL-728 12-bit, 2-ch Isolated AO ISA CardPCL-10120-1 20-pin Flat Cable, 1 mPCL-10120-2 20-pin Flat Cable, 2 mPCLD-780 Screw Terminal Board w/ Two 20-pin Flat CablesPCLD-782 16-ch Isolated DI Board w/ 1m 20-pin Flat CablePCLD-785 16-ch Relay Board w/ One 1m 20-pin Flat CablePCLD-880 Wiring Board w/ Two 20-pin Flat Cables & AdapterADAM-3909 DB9 DIN-rail Wiring BoardADAM-3920 20-pin DIN-rail Flat Cable Wiring Board

IntroductionPCL-726, and PCL-728 are analog output cards with 12-bit analog output channels. You can individually configure each channel to any of the following ranges: 0 to +5 V, 0 to +10 V, ±5 V, ±10 V and 4 to 20 mA current loop (sink). Designed for use in industrial environments, these cards are ideal, economical solutions for applications that require multiple analog outputs or current loops.

PCL-726 PCL-728


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features


SpecificationsDigital Input

Channels 24 (shared with output)Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min.Interrupt Capable Ch. 1

Digital OutputChannels 24 (shared with input)Compatibility 5 V/TTLOutput Voltage Logic 0: 0.4 V max.

Logic 1: 2.4 V min.Output Capability Sink: 0.4 V max. @ 24 mA

Source: 2.4 V min. @ 15 mA

GeneralBus Type Universal PCI V2.2I/O Connectors 1 x 50-pin box header

2 x 20-pin box headerDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption Max: +5 V @ 294.9 mAOperating Temperature 0 ~ 65° C (32 ~ 149° F)Storage Temperature -25 ~ 80° C (-13 ~ 176° F)Storage Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)

PCI-1737U 24-ch Digital I/O Universal PCI Card

Ordering InformationPCI-1737U 24-ch Digital I/O Universal PCI CardPCL-10150-1.2 50-pin Flat Cable, 1.2 mPCLD-782B 24-ch IDI Board w/ 20-pin & 50-pin Flat CablesPCLD-785B 24-ch Relay Board w/ 20-pin & 50-pin Flat CablesPCLD-7216 16-ch SSR I/O Module Carrier BoardPCLD-885 16-ch Power Relay Board w/ 20p & 50p Flat CablesADAM-3950 50-pin DIN-rail Flat Cable Wiring Board

Pin Assignments

ISA-Compatible with PCL-724

24 TTL digital I/O channels

Emulates mode 0 of 8255 PPI

Interrupt handling

Opto-22 compatible 50-pin connectors

Output status readback

PCI universal card


Features








GeneralBus Type Universal PCI V2.2I/O Connectors 2 x 50-pin box headerDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption Max: +5 V @ 540.8 mAOperating Temperature 0 ~ 65° C (32 ~ 149° F)Storage Temperature -25 ~ 80° C (-13 ~ 176° F)Storage Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)

PCI-1739U 48-ch Digital I/O Universal PCI Card




Interrupt handling



PCI universal card

Ordering InformationPCI-1739U 48-ch Digital I/O Universal PCI CardPCL-10150-1.2 50-pin Flat Cable, 1.2 mPCLD-782B 24-ch IDI Board w/ 20-pin & 50-pin Flat CablesPCLD-785B 24-ch Relay Board w/ 20-pin & 50-pin Flat CablesPCLD-7216 16-ch SSR I/O Module Carrier BoardPCLD-885 16-ch Power Relay Board w/ 20p & 50p Flat CablesADAM-3950 50-pin DIN-rail Flat Cable Wiring Board

Pin Assignments


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features


PCI-1751 48-ch Digital I/O and 2-ch Counter PCI Card



Logic 1: 2 V min.Interrupt Capable Ch. 4



Source: 2.4 V @ 15 mA

Counter/TimerChannels 3Resolution 2 x 16-bit counters, or 1 x 32-bit counter

(jumper selectable) 1 x 16-bit event counter

Compatibility 5 V/TTLMax. Input Frequency 10 MHzReference Clock Internal: 10 MHz

External Clock Frequency: 10 MHz External Voltage Range: 5 V/TTL

GeneralBus Type Universal PCI V2.2I/O Connectors 1 x 68-pin SCSI female connectorDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: 5 V @ 850 mA

Max: 5 V @ 1.0 AOperating Temperature 0 ~ 70° C (32 ~ 158° F)Storage Temperature -20 ~ 80° C (-4 ~ 176° F)Storage Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)

48 TTL digital I/O lines


Buffered circuits for higher driving capacity than the 8255

Interrupt handling

Timer/Counter interrupt capability

Supports both dry and wet contact

Keeps the I/O port setting and DO state after system reset

BoardID switch

Ordering InformationPCI-1751 48-ch Digital I/O and Counter PCI CardPCL-10168-1 68-pin SCSI Shielded Cable, 1 mPCL-10168-2 68-pin SCSI Shielded Cable, 2 mADAM-3968 68-pin DIN-rail SCSI Wiring BoardADAM-3968/20 68-pin SCSI to 3 20-pin Box Header TerminalADAM-3968/50 68-pin SCSI to 2 50-pin Box Header TerminalPCLD-8751 48-ch Isolated Digital Input BoardPCLD-8761 24-ch Replay/ Isolated Digital Input BoardPCLD-8762 48-ch Relay Board

Pin Assignments

IntroductionPCI-1751U is a 48-bit digital I/O card for the PCI bus. Its 48 bits are divided into six 8-bit I/O ports and users can configure each port as input or output via software. PCI-1751 also provides one event counter and two 16-bit timers, which can be cascaded to become a 32-bit timer.


Features

PCI-1753 96-ch Digital I/O PCI Card

Up to 96 TTL digital I/O lines



Multiple-source interrupt handling

Interrupt output pin for simultaneously triggering external devices with the interrupt

Output status read-back

“Pattern match” and “Change of state” interrupt functions for critical I/O monitoring



High-density 100-pin SCSI connector

IntroductionPCI-1753 is a 96-bit digital I/O card for the PCI bus. The card emulates mode 0 of the 8255 PPI chip, but the buffered circuits offer a higher driving capability than the 8255. The 96 I/O lines are divided into twelve 8-bit I/O ports: A0, B0, C0, A1, B1, C1, A2, B2, C2, A3, B3 and C3. You can configure each port as input or output via software.

SpecificationsDigital Input/Output

I/O Channels 96 digital I/O linesProgramming Mode 8255 PPI mode 0Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min. Output Voltage Logic 0: 0.44 V max.



GeneralBus Type PCI V2.2I/O Connector 1 x 100-pin SCSI female connectorDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: +5 V @ 400 mA

Max: +5 V @ 2.7 AOperating Temperature 0 ~ 60° C (32 ~ 140° F) (refer to IEC 68-2-1, 2)Storing Temperature -20 ~ 70° C (-4 ~ 158° F) (refer to IEC 68-2-3)Storing Humidity 5 ~ 95% RH, non-condensing

Ordering InformationPCI-1753 96-ch Digital I/O PCI CardADAM-3968 68-pin DIN-rail SCSI Wiring BoardADAM-3968/20 68-pin SCSI to 3 20-pin Box Header TerminalADAM-3968/50 68-pin SCSI to 2 50-pin Box Header TerminalPCLD-8751 48-ch Isolated Digital Input BoardPCLD-8761 24-ch Replay/ Isolated Digital Input BoardPCLD-8762 48-ch Relay BoardPCL-10268 100-pin to Two 68-pin SCSI Cables, 1 m and 2 m


Pin Assignments


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features



Channels 24 (shared with output)Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V @ -0.2 mA

Logic 1: 2.0 V @ 20 mAInterrupt Capable Ch. 2

Digital Output Channels 24 (shared with input)Compatibility 5 V/TTLOutput Voltage Logic 0: 0.5 V max. @ -24 mA

Logic 1: 3.7 V max. @ 24 mAOutput Capability Sink: 24 mA

Source: 15 mA

GeneralBus Type Universal PCI V2.2I/O Connectors 1 x DB25 female connectorDimensions (L x H) 120 x 64 mm (4.7" x 2.5") Low profile MD1 Power Consumption Typical: 5 V @ 140 mA

Max: 5 V @ 200 mAOperating Temperature 0 ~ 70° C (32 ~ 158° F)Storage Temperature -20 ~ 80° C(-4 ~ 176° F)Storage Humidity 5 ~ 95% non-condensing

PCI-1757UP 24-ch Digital I/O Low Profile Universal PCI Card

Low profile PCI form factor

Universal PCI bus

24 TTL level digital I/O channels


Buffered circuits provide higher driving capability


I/O configurable by software or on board DIP switch


BoardID™ switch

Convenient DB25 connector


Ordering InformationPCI-1757UP 24-ch Digital I/O Low Profile Universal PCI CardADAM-3925 DB25 DIN-rail Wiring BoardPCL-10125-1 DB25 Cable, 1 mPCL-10125-3 DB25 Cable, 3 mPCLD-782B 24-ch IDI Board w/ 20-pin & 50-pin Flat CablesPCLD-785B 24-ch Relay Board w/ 20-pin & 50-pin Flat Cables

Pin Assignments

IntroductionPCI-1757UP is a 24-channel digital I/O low profile PCI card that meets the PCI standard REV.2.2 (universal PCI expansion card). The card also works with 3.3 V and 5 V PCI slots, and provides you with 24 parallel digital input/output channels that emulate mode 0 of the 8255 PPI chip. However, the buffered circuits offer a higher driving capability than the 8255.


Features


PCL-720+


Channels 32Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min.




Counter/TimerChannels 3Resolution 16 bitsCompatibility 5 V/TTLMax. Input Frequency 1 MHzReference ClockInternal: Selectable 1 MHz, 100 kHz, or 10 kHz base clock External Clock Frequency: Jumper selectable divider: x2, x1, x0.5, and x0.25Programmable Counter 6 Modes

64-ch Digital I/O and Counter ISA Card

32 TTL-level digital input channels

32 TTL-level digital output channels

High-output driving capacity

Low-input loading

3 programmable counter/timer channels

User configurable clock source

Breadboard area for custom circuits

GeneralBreadboard Area 540 (30 x 18) plated-through "donuts", each with a

.036" hole on 0.10" centers. Further, provide +5 V on the left side, and provide GND on the right side

Bus Type ISAI/O Connectors 5 x 20-pin box headerDimensions (L x H) 185 x 100 mm (7.3" x 4")Power Consumption +5 V @ 500 mAOperating Temperature 0 ~ 60° C (32 ~ 140° F)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)

Ordering InformationPCL-720+ 64-ch Digital I/O and Counter ISA CardPCL-10120-1 20-pin Flat Cable, 1 mPCL-10120-2 20-pin Flat Cable, 2 mPCLD-780 Screw Terminal Board w/ Two 20-pin Flat CablesPCLD-782 16-ch Isolated DI Board w/ 1 m 20-pin Flat CablePCLD-785 16-ch Relay Board w/ One 1 m 20-pin Flat CablePCLD-786 8-ch SSR I/O Module Board w/ 20-pin Flat CablePCLD-885 16-ch Power Relay Board w/ 20p & 50p Flat CablesADAM-3920 20-pin DIN-rail Flat Cable Wiring Board

IntroductionThe PCL-720+ digital I/O and counter card is PC-compatible add-on cards with 32 digital input channels, 32 digital output channels and three programmable counter/timer channels. Their digital I/O channels are TTL-compatible and use 74LS244 driver/ buffer circuits to provide high output driving capacity. These buffered circuits also require lower input loading current than regular TTL circuits. The cards' 8254 programmable counter/timer provides three flexible 16-bit counter/timer channels. You can generate waves and pulses by programming the 8254. Jumper settings determine the clock crystal frequency. The cards also includes a breadboard area perfect for customized circuits.


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features



Channels 144 (24 channels x 6 ports) shared with outputCompatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min.Interrupt Capable Ch. Bits 0 and 3 of Port C can generate an interrupt to IRQ

2, 3, 4, 5, 6 or 7

Digital OutputChannels 144 (24 channels x 6 ports) shared with inputCompatibility 5 V/TTLOutput VoltagePort A, B Logic 0: 0.5 V max. Logic 1: 2.4 V min. Port C Logic 0: 0.4 V max. Logic 1: 2.0 V min. Output CapabilityPort A, B Sink: 12 mA Source: 8 mA Port C Sink: 24 mA Source: 15 mA

GeneralBus Type ISAPower Consumption Typical: +5 V @ 1.3 A

Max: +5 V @ 1.8 AOperating Temperature 0 ~ 60° C (32 ~ 140° F)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Operating Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)I/O Connectors 6 x 50-pin box headerDimensions (L x H) 334 x 100 mm (13.2" x 3.9")

Emulates 8255 PPI mode 0


Interrupt handling


Pin compatible with Opto-22 I/O module racks

PCL-722 144-ch Digital I/O ISA Card

Ordering InformationPCL-722 144-ch Digital I/O ISA CardPCL-10150-1.2 50-pin Flat Cable, 1.2 mPCLD-782B 24-ch IDI Board w/ 20-pin & 50-pin Flat CablesPCLD-785B 24-ch Relay Board w/ 20-pin & 50-pin Flat CablesPCLD-7216 16-ch SSR I/O Module Carrier BoardPCLD-885 16-ch Power Relay Board w/ 20p & 50p Flat CablesADAM-3950 50-pin DIN-rail Flat Cable Wiring Board

Pin Assignments


Features








GeneralBus Type ISAI/O Connectors 1 x DB50 female connectorDimensions (L x H) 125 x 100 mm (4.9" x 3.9")Power Consumption Typical: +5 V @ 0.5 A

Max: +5 V @ 0.8 AOperating Temperature 0 ~ 60° C (32 ~ 140° F)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)



Pin Assignments



Interrupt handling




8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features








GeneralBus Type ISAI/O Connectors 2 x 50-pin box hederDimensions (L x H) 185 x 100 mm (7.3" x 3.9")Power Consumption Typical: +5 V @ 0.5 A

Max.: +5 V @ 0.8 AOperating Temperature 0 ~ 60° C (32 ~ 140° F)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)




Interrupt handling




Pin Assignments


Features


PCI-1730 PCI-1733

SpecificationsDigital Input (PCI-1730 only)

Channels 16 (16-ch/group)Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min.Interrupt Capable Ch. 2 (DI0, DI1)

Isolated Digital InputChannels 16 (16-ch/group)Input Voltage Logic 0: 1 V max. (2 V max.)

Logic 1: 5V min. (30 V max.)Interrupt Capable Ch. 2 (IDI0, IDI1)Isolation Protection 2,500 VDC

Opto-Isolator Response 25 µsInput Resistance 2.7 kW @ 1 W

Digital Output (PCI-1730 only)Channels 16 (16-ch/group)Compatibility 5 V/TTLOutput Voltage Logic 0: 0.8 V max.


Source: 15 mA

Isolated Digital OutputChannels 16 (16-ch/group)Output Type Sink type (NPN)Isolation Protection 2,500 VDC

Output Voltage 5 ~ 40 VDC

Sink Current 200 mA max./channelOpto-Isolator Response 25 µs

ISA-Compatible with PCL-730/733/734

32-ch isolated digital I/O (16-ch digital input and 16-ch digital output)

32-ch TTL isolated digital I/O (16-ch digital input and 16-ch digital output)

High output driving capacity

Interrupt capability

Two 20-pin connectors for isolated digital I/O channels and two for TTL digital I/O channels

D-type connector for isolated input and output channels

High-voltage isolation on output channels

32-ch Isolated Digital I/O PCI Card

32-ch Isolated Digital Input PCI Card

32-ch Isolated Digital Output PCI Card

PCI-1730PCI-1733PCI-1734

IntroductionPCI-1730, PCI-1733, and PCI-1734 offer isolated digital input channels as well as isolated digital output channels with isolation protection up to 2,500 VDC, which makes them ideal for industrial applications where high-voltage isolation is required. There are also 32 TTL digital I/O channels on PCI-1730.

GeneralBus Type PCI V2.2I/O Connectors 1 x DB37 female connector

4 x 20-pin box header (PCI-1730 only)Dimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: 5 V @ 250 mA, 12 V @ 35 mA

Max: 5 V @ 400 mA, 12 V @ 60 mAOperating Temperature 0 ~ 60° C (32 ~ 140° F)Storage Temperature -25 ~ 85° C (-13 ~ 185° F)Storage Humidity 5 ~ 95% RH, non-condensing (see IEC 68-2-3)

Ordering InformationPCI-1730 32-ch Isolated Digital I/O PCI Card PCI-1733 32-ch Isolated Digital Input PCI Card PCI-1734 32-ch Isolated Digital Output PCI Card PCL-10120-1 20-pin Flat Cable, 1 mPCL-10120-2 20-pin Flat Cable, 2 mPCLD-782 16-ch Isolated DI Board w/ 1m 20-pin Flat CableADAM-3920 20-pin DIN-rail Flat Cable Wiring BoardPCLD-885 16-ch Power Relay Board w/ 20p & 50p Flat Cables PCLD-780 Screw Terminal Board w/ Two 20-pin Flat CablesPCLD-785 16-ch Relay Board w/ One 1m 20-pin Flat CablePCLD-786 8-ch SSR I/O Module Board w/ 20-pin Flat CablePCLD-880 Wiring Board w/ Two 20-pin Flat Cables & AdapterADAM-3937 DB37 DIN-rail Wiring BoardPCL-10137-1 DB37 Cable, 1 mPCL-10137-2 DB37 Cable, 2 mPCL-10137-3 DB37 Cable, 3 m

PCI-1734


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features


PCI-1750 32-ch Isolated Digital I/O and 3-ch Counter PCI Card

SpecificationsIsolated Digital Input

Channels 16Input Voltage Logic 0: 2 V max.

Logic 1: 5 V min. (50 VDC max.) or dry contactInterrupt Capable Ch. 2Isolation Protection 2,500 VDC

Opto-Isolator Response 100 µs

Isolated Digital OutputChannels 16Output Type Sink (NPN)Isolation Protection 2,500 VDC


Sink Current 200 mA max. per channelOpto-Isolator Response 100 µs

Counter/TimerChannels 1Resolution 1 x 32-bit timer

1 x 16-bit isolated counterCompatibility 5 V/TTLMax. Input Frequency 1 MHzIsolation Protection 2,500 VDC

GeneralBus Type PCI V2.2I/O Connectors 1 x DB37 female connector

1 x 2-pin terminal block for extended groundDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: 5 V @ 850 mA

Max.: 5 V @ 1.0 A

16 isolated DI and 16 isolated DO channels

High voltage isolation on all isolated channels (2,500 VDC)

High sink current on isolated output channels (200 mA/channel)

Supports dry contact or 5 ~ 50 VDC isolated inputs

Interrupt handling

Timer/counter interrupt capability

Operating Temperature 0 ~ 70° C (32 ~ 158° F)Storage Temperature -20 ~ 80° C (-4 ~ 176° F)Storage Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)

Ordering InformationPCI-1750 32-ch Isolated Digital I/O and Counter PCI CardPCL-10137-1 DB37 Cable, 1 mPCL-10137-2 DB37 Cable, 2 mPCL-10137-3 DB37 Cable, 3 mADAM-3937 DB37 DIN-rail Wiring Board

Pin Assignments

IntroductionPCI-1750 offers 16 isolated digital input channels, 16 isolated digital output channels, and one isolated counter/timer for the PCI bus. With isolation protection of 2,500 VDC, and dry contact support, PCI-1750 is ideal for industrial applications where high-voltage protection is required. Each I/O channel of the PCI-1750 corresponds to a bit in a PC I/O port. This makes PCI-1750 very easy to program. This card also offers a counter or timer interrupt and two digital input interrupt lines to a PC. So you can then easily do configurations by software.


Features64 isolated digital output channelsHigh-voltage isolation on output channels (2,500 VDC)2,000 VDC ESD protectionWide output range (5 ~ 40 VDC)High-sink current on isolated output channels (200 mA max./channel)Output status readbackKeeps the output settings and values after system hot resetChannel-freeze functionHigh-density 100-pin SCSI connectorSupport sink

Features64 isolated digital input channels

Either +/- voltage input for DI by group

High-voltage isolation on input channels (2,500 VDC)

High over-voltage protection (70 VDC)

Wide input range (10 ~ 50 VDC)

Interrupt handling capability


FeaturesEither +/- voltage input for DI by group





64-ch Isolated Digital Output Universal PCI Card

64-ch Isolated Digital Input PCI Card

64-ch Isolated Digital I/O PCI Card

PCI-1752UPCI-1754PCI-1756

PCI-1752U PCI-1754 PCI-1756RoHSCOMPLIANT2002/95/EC



SpecificationsIsolated Digital Output

Channels 64 (16-ch/group)Output Type Sink (NPN)Isolation Protection 2,500 VDC


Sink Current 200 mA max./channelOpto-isolator 25 µs Response

GeneralBus Type Universal PCI V2.2I/O Connectors 1 x 100-pin SCSI female

connectorDimensions (L x H) 175 x 100mm (6.9" x 3.9")Power Consumption Typical: +5 V @ 230 mA

Max.: +5 V @ 500 mAOperating 0 ~ 60° C (32 ~ 140° F) Temperature (IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95% RH, (IEC 68-2-3)

non-condensing

Ordering InformationPCI-1752U 64-ch Isolated Digital

Output Universal PCI CardPCL-10250-1 100-pin SCSI to Two 50-

pin SCSI Cable, 1 mADAM-3951 50-pin DIN-rail Wiring

Board w/ LED Indicators


Channels 64 (16-ch/group)Input Voltage Logic 0: 3 V max.

Logic 1: 10 V min. (50 V max.)

Input Current 10 VDC @ 1.7 mA, (Typical) 12 VDC @ 2.1 mA 24 VDC @ 4.4 mA, 48 VDC @ 9.0 mA 50 VDC @ 9.4 mAInterrupt Capable Ch. 4Isolation Protection 2,500 VDC

Overvoltage 70 VDC

ProtectionESD 2,000 VDC

Opto-Isolator 25 µs Response

GeneralBus Type PCI V2.2I/O Connectors 1 x 100-pin SCSI female


Max.: +5 V @ 450 mAOperating 0 ~ 60° C (32 ~ 140° F) Temperature (IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95% RH (IEC 68-2-3)

non-condensing

Ordering InformationPCI-1754 64-ch Isolated Digital Input

PCI CardPCL-10250-1 100-pin SCSI to Two 50-pin

SCSI Cable, 1 mADAM-3951 50-pin DIN-rail Wiring Board

w/ LED Indicators


Channels 32 (16-ch/group)Input Voltage Logic 0: 3 V max.


Interrupt Capable Ch. 2 (IDI0, IDI16)Isolation Protection 2,500 VDC

Overvoltage Protection 70 VDC

ESD 2,000 VDC

Opto-Isolator Response 25 µsInput Current 10 VDC @ 1.7 mA, 12 VDC @ 2.1

mA 24 VDC @ 4.4 mA, 48 VDC @ 9.0 mA 50 VDC @ 9.4 mA

Isolated Digital OutputChannels 32 (16-ch/group)Output Type Sink (NPN)Isolation Protection 2,500 VDC


Sink Current 200 mA max./channelOpto-isolator Response 25 µs

GeneralBus Type PCI V2.2I/O Connectors 1 x 100-pin SCSI female


Max.: +5 V @ 475 mAOperating 0 ~ 60° C (32 ~ 140° F) Temperature (IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95 % (IEC 68-2-3)

non-condensing

Ordering InformationPCI-1756 64-ch Isolated Digital I/O PCI

CardPCL-10250-1 100-pin SCSI to Two 50-pin

SCSI Cable, 1 mADAM-3951 50-pin DIN-rail Wiring Board

w/ LED Indicators


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features

Feature DetailsInterrupt Function (PCI-1758UDI)PCI-1758UDI provides an interrupt function for every digital input channel. You can disable/enable the interrupt functions, and select trigger type by setting the Rising Edge Interrupt Registers or Falling Edge Interrupt Registers of the card. When the interrupt request signals occur, software will service these interrupt requests by ISR. The multiple interrupt sources provide the card with more flexibility.

Digital Filter Function (PCI-1758UDI)The digital filter function is used to eliminate glitches on input data and reduce the number of changes to examine and process. The filter blocks pulses that are shorter than the specified timing interval and passes pulses that are twice as long as the specified interval. Intermediate-length pulses that are longer than half of the interval, but less than the interval, may or may not pass the filter depending on your settings.

Pin Assignments

PCI-1758UDI


123456789

1011121314151617181920212223242526272829303132333435363738394041424344454647484950

60616263646566676869707172737475767778798081828384858687888990919293949596979899

100

515253545556575859

NCNC

PAB_COMMPAB_COMM

PB_IDI00

PB_IDI07PB_IDI06PB_IDI05PB_IDI04PB_IDI03PB_IDI02PB_IDI01

PA_IDI00

PA_IDI07PA_IDI06PA_IDI05PA_IDI04PA_IDI03PA_IDI02PA_IDI01

NCNCNCNCNCNC

P89_COMMP89_COMM

P9_IDI00

P9_IDI07P9_IDI06P9_IDI05P9_IDI04P9_IDI03P9_IDI02P9_IDI01

P8_IDI00

P8_IDI07P8_IDI06P8_IDI05P8_IDI04P8_IDI03P8_IDI02P8_IDI01

NCNCNCNCNCNC

NCNC

PEF_COMMPEF_COMM

PF_IDI00

PF_IDI07PF_IDI06PF_IDI05PF_IDI04PF_IDI03PF_IDI02PF_IDI01

PE_IDI00

PE_IDI07PE_IDI06PE_IDI05PE_IDI04PE_IDI03PE_IDI02PE_IDI01

NCNCNCNCNCNC

PCD_COMMPCD_COMM

PD_IDI00

PD_IDI07PD_IDI06PD_IDI05PD_IDI04PD_IDI03

PD_IDI02PD_IDI01

PC_IDI00

PC_IDI07PC_IDI06PC_IDI05PC_IDI04PC_IDI03PC_IDI02PC_IDI01

NCNCNCNCNCNC

1234567891011121314151617181920212223242526272829303132333435363738394041424344454647484950

60616263646566676869707172737475767778798081828384858687888990919293949596979899

100

515253545556575859

NCNC

NCNCNCNCNC

P4_IDI00P4_IDI01P4_IDI02P4_IDI03P4_IDI04P4_IDI05P4_IDI06P4_IDI07P5_IDI00P5_IDI01P5_IDI02P5_IDI03P5_IDI04P5_IDI05P5_IDI06P5_IDI07

P45_COMMP45_COMM

NC

NCNCNCNCNC

P6_IDI00P6_IDI01P6_IDI02P6_IDI03P6_IDI04P6_IDI05P6_IDI06P6_IDI07P7_IDI00P7_IDI01P7_IDI02P7_IDI03P7_IDI04P7_IDI05P7_IDI06P7_IDI07P67_COMMP67_COMM

NC

NCNC

NCNCNCNCNC


P01_COMMP01_COMM

NC

NCNCNCNCNC


P23_COMMP23_COMM

NC

CNB CNA

PCI-1758UDIPCI-1758UDO

PCI-1758UDO128 isolated digital output channelsHigh-voltage isolation on output channels (2,500 VDC)Wide output range (5 ~ 40 VDC)High-sink current for isolated output channels (90 mA max./channel)Current protection for each portBoardID™ switchOutput status read-backDigital output value retained after hot system resetProgrammable Power-up StatesWatchdog timer

PCI-1758UDI128 isolated digital input channelsWide input range (5 ~ 25 VDC)High ESD protection (2,000 VDC)Digital Filter functionBoardID™ switchInterrupt handling capability for each channel


Channels PCI-1758UDI: 128Input Voltage Logic 0: 2.5 V max.

Logic 1: 5 V min. (25 V max.)Interrupt Capable Ch. PCI-1758UDI: 128Isolation Protection 2,500 VDC

Opto-Isolator Response 20 µsInput Resistance 3 kW

Isolated Digital OutputChannels PCI-1758UDO: 128Output Type Sink (NPN)Isolation Protection 2,500 VDC


Sink Current 90 mA max./channelOpto-isolator Response 20 µs

GeneralBus Type Universal PCI V2.2I/O Connectors 1 x MINI-SCSI HDRA-E100 female connectorDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption

PCI-1758UDI PCI-1758UDOTypical +5 V @ 0.3 A +5 V @ 1.1 AMax. +5 V @ 0.6 A +5 V @ 2.2 A

Operating Temperature 0 ~ 60° C (32 ~ 140° F) (IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95 % (IEC 68-2-3) non-condensing

Ordering InformationPCI-1758UDI 128-ch Isolated DI Universal PCI CardPCI-1758UDO 128-ch Isolated DO Universal PCI CardPCL-101100S-1 100-pin SCSI Cable, 1 mPCL-101100S-2 100-pin SCSI Cable, 2 mADAM-39100 100-pin DIN-rail SCSI Wiring Board

128-ch Isolated Digital Input Universal PCI Card128-ch Isolated Digital Output Universal PCI Card

PCI-1758UDOPCI-1758UDI


Features



Channels 8 (Sink)Input Voltage Logic 0: 1.0 V max.

Logic 1: 4.5 V min. (12 V max.)Interrupt Capable Ch. 8 (IDI0 ~ IDI7)Isolation Protection 2,500 VDC

Opto-Isolator Response 25 µsInput Resistance 2 kW 1/4 W

Counter/TimerChannels 8Resolution 16 bitsCompatibility 5 V/TTLMax. Input Frequency 500 HzIsolation Protection 2,500 VDC

PWM Channels 2Digital Noise Filter Min. effective high input period ≥ [(2 ~ 65535) x 5 ms]

+ 5 ms Min. effective low input period ≥ [(2 ~ 65535) x 5 ms] + 5 ms

Relay OutputChannels 8Relay Type 2 x Form C, and 6 x Form AContact Rating 120 VDC @ 0.5 A, or 30 VDC @ 1 ARelay on Time 5 ms max.Relay off Time 5 ms max.Life Span 200,000 operations @ 0.5 A 120 VAC

500,000 operations @ 1.0 A 30 VDC

Resistance Contact: < 100 mW Insulation: 50 MW

IntroductionPCI-1760U relay actuator and isolated digital input card is a PC add-on card for the PCI bus. It meets the PCI standard Rev. 2.2 (Universal PCI expansion card), and works with both 3.3 V and 5 V PCI slots. It provides 8 opto-isolated digital inputs with isolation protection of 2,500 VDC for collecting digital inputs in noisy environments, 8 relay actuators that can be used as a on/off control devices or small power switches, and 2 isolated PWM (Pulse Width Modulation) outputs for custom applications.

For easy monitoring, each relay is equipped with one red LED to show its on/off status. Each isolated input supports both dry contact and wet contact so that it can easily interface with other devices when no voltage is present in the external circuit.

PCI-1760UUniversal PCI card, for 3.3 V and 5 V PCI slot

8 opto-isolated digital input channels

8 relay actuator output channels

2 opto-isolated PWM outputs

LED indicators to show activated relays

Jumper selectable dry contact/wet contact input signals

Up event counters for DI

Programmable digital filter function for DI

Pattern match interrupt function for DI

"Change of state" interrupt function for DI

Universal PCI and BoardID switch

8-ch Relay and 8-ch Isolated Digital Input Universal PCI Card with 10-ch Counter/Timer

GeneralBus Type Universal PCI V2.2I/O Connectors 1 x DB37 female connectorDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: +5 V @ 450 mA

Max: +5 V @ 850 mAOperating Temperature 0 ~ 60° C (32 ~ 140° F) (IEC 68 - 2 - 1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95 % RH, non-condensing (IEC 68-2-3)

Ordering InformationPCI-1760U 8-ch Relay/IDI PCI Card w/ 10-ch Counter/TimerPCL-10137-1 DB37 Cable, 1 mPCL-10137-2 DB37 Cable, 2 mPCL-10137-3 DB37 Cable, 3 mADAM-3937 DB37 DIN-rail Wiring Board


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features




Logic 1: 5V min. (50V max.).Interrupt Capable Ch. 8Isolation Protection 3,750 VDC


Opto-Isolator Response 25 µsInput Resistance 5,600 WInput Current 1.6 mA @ 10 VDC, 8.9 mA @ 50 VDC

Relay OutputChannels 8Relay Type SPDT (4 x Form C, and 4 x Form A)Contact Rating 250 VAC @ 3 A, or 24 VDC @ 3 ARelay on Time 15 ms max.Relay off Time 5 ms max.Life Span 2 x 107 operationsResistanceContact: 50 MW Insulation: 1 GW min.

8-ch Relay and 8-ch Isolated Digital Input PCI Card

GeneralBus Type PCI V2.2I/O Connectors 1 x DB37 female connectorDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: +5 V @ 220 mA

Max.: +5 V @ 750 mAOperating Temperature 0 ~ 60° C (32 ~ 140° F) (IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95 % RH, non-condensing (IEC 68-2-3)

Ordering InformationPCI-1761 8-ch Relay/Isolated Digital Input PCI CardPCL-10137-1 DB37 Cable, 1 mPCL-10137-2 DB37 Cable, 2 mPCL-10137-3 DB37 Cable, 3 mADAM-3937 DB37 DIN-rail Wiring BoardPCLD-880 Wiring Board w/ Two 20-pin Flat Cables & Adapter


8 relay output channels and 8 isolated digital input channels


4 Form C and 4 Form A type relay output channels

Male DB37 matching connector included


Retained relay output values when hot system reset


High ESD protection (2,000 VDC)




BoardID™ switch

PCI-1761

IntroductionThe PCI-1761 relay actuator and isolated DI card is an add-on card for the PCI bus. It provides 8 optically-isolated digital inputs with isolation protection of 3,750 VDC for collecting digital inputs in noisy environments and 8 relay actuators for serving as on/off control devices or small power switches. For easy monitoring, each relay is equipped with one red LED to show its on/off status. The PCI-1761’s eight optically-isolated digital input channels are ideal for digital input in noisy environments or with floating potentials.

The PCI-1761 digital input channels feature a rugged isolation protection for industrial, lab and machinery automation applications. It durably withstands voltage up to 3,750 VDC, protecting your host system from any incidental harms. If connected to an external input source with surge-protection, the PCI-1761 can offer up to a maximum of 2,000 VDC ESD (Electrostatic Discharge) protection. Even with an input voltage rising up to 70 VDC, the PCI-1761 can still manage to work properly, albeit for only a short period of time.


Features


IntroductionThe PCI-1762 relay actuator and isolated DI card is a PC add-on card for the PCI bus. It provides 16 opto-isolated digital inputs with isolation protection of 2,500 VDC for collecting digital inputs in noisy environments, 16 relay actuators for serving as on/off control devices or small power switches. For easy monitoring, each relay is equipped with one red LED to show its on/off status. The PCI-1762’s sixteen optically-isolated digital input channels are ideal for digital input in noisy environments or with floating potentials.

PCI-176216 relay output channels and 16 isolated digital input channels


Jumper selectable Form A/Form B-type relay output channel


Retain relay output values when hot system reset


High ESD protection (2,000 VDC)




High-density DB62 connector

BoardID™ switch

16-ch Relay and 16-ch Isolated Digital Input PCI Card



Logic 1: 10 V min. (50 V max.)Interrupt Capable Ch. 2Isolation Protection 2,500 VDC


Opto-Isolator Response 25 µsInput Resistance 4.7 KW

Relay OutputChannels 16Relay Type SPDT (Form A or Form B, jumper selectable)Contact Rating 0.5 A @ 125 VAC or 1 A @ 30 VDC

Relay on Time 6 ms max.Relay off Time 4 ms max.Life Span 2 x 105 ops. min. (0.5 A @ 125 VAC),

5 x 105 ops. min. (1 A @ 30 VDC) Resistance Contact: 50 MW

Insulation: 1,000 MW min. (at 500 VDC)

GeneralBus Type PCI V2.2I/O Connectors 1 x DB62 female connectorDimensions (L x H) 175 x 100 mm (69" x 3.9")Power Consumption Typical: +5 V @ 250 mA

Max: +5 V @ 620 mAOperating Temperature 0 ~ 60° C (32 ~ 140° F) (IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 - 95 % non-condensing (IEC 68-2-3)

Ordering InformationPCI-1762 16-ch Relay/Isolated Digital Input PCI CardPCL-10162-1 DB62 Cable, 1 mPCL-10162-3 DB62 Cable, 3 mADAM-3962 DB62 DIN-rail Wiring Board

Pin Assignments


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features



Channels 8Input Voltage 5 ~ 24 VDC

Isolation Protection 1,500 VDC

Input Resistance 560 WInput Current 60 mA max.

Non-isolated Digiteal InputChannels 8 (Jumper-selectable)Input Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min. (5.25 V max.)

Relay OutputChannels 8Relay Type SPDT (4 x Form C and 4 x Form A)Contact Rating 120 VAC @ 0.5 A, or 30 VDC @ 1 ARelay on Time 8 ms max.Relay off Time 8 ms max.Life Span 1 x 107 operationsResistance Contact: 50 MW

Insulation: 100 MW min.

8-ch Relay and 8-ch Isolated Digital Input ISA Card

GeneralBus Type ISAI/O Connectors 1 x DB37 female connectorDimensions (L x H) 147 x 100 mm (5.75" x 3.9")Power Consumption +5 V @ < 0.2 A; +12 V @ 33 mA for each relay

< 0.27 A if all eight relays are energizedOperating Temperature 0 ~ 60° C (32 ~ 140° F) (IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95 % RH, non-condensing (IEC 68-2-3)

Ordering InformationPCL-725 8-ch Relay/Isolated Digital Input ISA CardPCL-10137-1 DB37 Cable, 1 mPCL-10137-2 DB37 Cable, 2 mPCL-10137-3 DB37 Cable, 3 mADAM-3937 DB37 DIN-rail Wiring BoardPCLD-880 Wiring Board w/ Two 20-pin Flat Cables & Adapter

8 x relay output channels and 8 x isolated digital input channels


4 x Form C and 4 x Form A type relay output channels



PCL-725

IntroductionThe PCL-725 relay actuator and isolated digital input card offers 8 relay actuators and 8 opto-isolated digital inputs on a single board.Typically, the onboard relays can serve as on/off control devices or small power switches. The 8 x opto-isolated DI channels are ideal devices for collecting digital inputs under noisy environment or floating potential. Also, the 8 x isolated inputs provide the best method to prevent any ground loop problems.

For easy monitoring, each relay is equipped with one red LED to reflect its on/off status. Each input channel is jumper selectable to either isolated or non-isolated input. Access to input and output channels is made possible through an onboard 37-pin D type connector.


Features


PCL-735 12-ch Relay ISA Card with 16-ch Digital I/O

SpecificationsRelay Output

Channels 12Relay Type SPDT, Form CContact Rating 2 A @ 30 VDC, 1 A @ 125 VAC

Relay on Time 5 ms typicalRelay off Time 5 ms typicalLife Span > 5 x 105 operations @ 30 VDC and 2 A

> 2 x 106 operations @ 30 VDC and 1 AResistance Contact: 50 MW

Insulation: 1 GW @ 500 VDC min.

GeneralBus Type ISAI/O Connectors 1 x DB37 female connectorDimensions (L x H) 155 x 100 mm (6.1" x 3.9")Power Consumption Typical: +5 V @ 280 mA

Max.: +12 V @ 200 mAOperating Temperature 0 ~ 60° C (32 ~ 140° F)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95% RH, non-condensing (refer to IEC 68-2-3)

12 relay outputs




Ordering InformationPCL-735 12-ch Relay ISA Card w/ 16-ch Digital I/OPCL-10137-1 DB37 Cable, 1 mPCL-10137-2 DB37 Cable, 2 mPCL-10137-3 DB37 Cable, 3 mADAM-3937 DB37 DIN-rail Wiring BoardPCLD-880 Wiring Board w/ Two 20-pin Flat Cables & Adapter

Pin Assignments

IntroductionIdeal for applications such as on/off control or signal switching, the PCL-735 12-channel relay actuator provides 12 SPDT relays on a half-size card. The on/off status of each relay is easy to monitor. A red LED next to each relay shows its on/off status, and the software can read each relay’s status. An onboard DB-37 connector provides access to all output channels.


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16



Features


8 independent 16-bit counters

8 programmable clock source

8 digital TTL outputs and 8 digital TTL inputs

Up to 20 MHz input frequency

Multiple counter clock source selectable

Counter output programmable

Counter gate function

Flexible interrupt source select

BoardID™ switch

PCI-1780U 8-ch, 16-bit Counter/Timer Universal PCI Card



Logic 1: 2.0 V min.Interrupt Capable Ch. CH0

Digital OutputChannels 8Compatibility 5 V/TTLOutput Voltage Logic 0: 0.8 V

Logic 1: 2.0 VOutput Capability Sink: 24 mA @ 0.8 V

Source: -15 mA @ 2.0 V

Counter/TimerChannels 8 (independent)Resolution 16 bitsCompatibility 5 V/TTLMax. Input Frequency 20 MHzReference Clock Internal: 20 MHz

External clock: 20 MHz max.Counter Modes 12 (programmable)Interrupt Capable Ch. 8PWM Channels 8

IntroductionPCI-1780U is a general purpose multi-channel counter/timer card for the PCI bus. It targets the AM9513 to implement the counter/timer function by CPLD. It provides eight 16-bit counter channels, 8 digital outputs and 8 digital inputs. Its powerful counter functions cater to a broad range of industrial and laboratory applications.

The card features 12 programmable counter modes, to provide one shot output, PWM output, periodic interrupt output, time-delay output, and to measure the frequency and the pulse width. The PCL-10168 shielded cable works well with PCI-1780U to reduce noise. Its wires are all twisted pairs, and the input signals and output signals are separately shielded, providing minimal cross talk between signals and the best protection against EMI/EMC problems.

GeneralBus Type Universal PCI V2.2I/O Connectors 1 x 68-pin SCSI female connectorDimensions (L x H) 175 x 100 mm (6.9" x 3.9")Power Consumption Typical: +5 V @ 900 mA

Max.: +5 V @ 1.2 AOperating Temperature 0 ~ 60° C (32 ~ 140° F) (IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95 % RH, non-condensing (IEC 68-2-3)

Ordering InformationPCI-1780 8-ch, 16-bit Counter/Timer Universal PCI CardPCL-10168-1 68-pin SCSI Shielded Cable, 1 mPCL-10168-2 68-pin SCSI Shielded Cable, 2 mADAM-3968 68-pin DIN-rail SCSI Wiring Board


Features


PCL-836 6-ch, 16-bit Counter/Timer ISA Card



Logic 1: 2.0 V min.

Digital Output Channels 16Compatibility 5 V/TTLOutput Voltage Logic 0: 0.8 V

Logic 1: 2.0 VOutput Capability Sink: 8 mA @ 0.8 V

Source: -0.4 mA @ 2.0 V

Counter/TimerChannels 6Resolution 16 bitsCompatibility 5 V/TTLMax. Input Frequency 10 MHzReference Clock Internal: 10 MHz

External clock: 10 MHzCounter Modes 6 programmable counter modesInterrupt Capable Ch. IRQ 2, 4, 5, 7, 10, 11, 12, 15 (jumper selectable)PWM Channels 3Digital Noise Filter 1.6 ms to 52 ms (programmable)

GeneralPower Consumption +5 V @ 360 mA (typical)

+5 V @ 400 mA (max.)Operating Temperature 0 ~ 60° C (32 ~ 140° F)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)Operating Humidity 5 ~ 95% RH non-condensing (refer to IEC 68-2-3) Connector 1 x DB37 female connector for counter 2 x 20-pin box header for digital I/ODimensions (L x H) 185 x 100 mm (7.3" x 3.9")

Periodic interrupt generation

6 independent 16-bit counters

Digital filter for noise reduction

Binary or BCD counting

Programmable frequency output

Complex duty-cycle output

Single-shot output

16-bit TTL input and 16-bit TTL output ports

Selectable interrupt input channel

Up to 10 MHz input frequency

Pulsewidth and period measurement

Time-delay generation

F/V conversion and accumulation

Ordering InformationPCL-836 6-ch, 16-bit Counter/Timer ISA CardPCL-10137-1 DB37 Cable, 1 mPCL-10137-2 DB37 Cable, 2 mPCL-10137-3 DB37 Cable, 3 mADAM-3937 DB37 DIN-rail Wiring BoardPCLD-880 Wiring Board w/ Two 20-pin Flat Cables & Adapter

Pin Assignments

IntroductionPCL-836 is a general purpose counter/timer and digital I/O card for PC/AT compatible computers. It provides six 16-bit counter channels. It also includes 16 digital outputs and 16 digital inputs. Two 8254 chips provide a variety of powerful counter/timer function modes to match your industrial and/or laboratory applications.

Unique Digital FilterPCL-836 includes a unique digital filter to eliminate noise on the input signal. The frequency can be adjusted to provide more stable output readings.


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16




Channels 16 single-ended / 8 differentialResolution 12 bitsMax. Sampling Rate 100 KHz* (DMA transfer) *80 kHz on P4-based (or upper) systemInput Impedance 10 MWSampling Modes Software, pacer or external

Input Range

PCM-3718H and PCM-3718HO

Bipolar ±10, ±5, ±2.5, ±1.25, ±0.625

Unipolar 0 ~ 10, 0 ~ 5, 0 ~ 2.5, 0 ~ 1.25

PCM-3718HGBipolar

±10, ±5, ±1, ±0.5, ±0.1, ±0.05, ±0.01,

±0.005

Unipolar 0 ~ 10, 0 ~ 1, 0 ~ 0.1, 0 ~ 0.01

Analog Output (PCM-3718HO only)Channels 1 (12 bits)Output Range

Internal Reference Unipolar (V) 0 ~ 5, 0 ~ 10

External Reference (V) 0 ~10, 0 ~ -10Slew Rate 10 V/µsOutput Impedance 0.1 W max.

Digital Input/OutputChannels 16, 5V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min.Output Voltage Logic 0: 0.33 V max. @ 6 mA

Logic 1: 3.84 V min. @ 6 mA

GeneralBus Type PC/104I/O Connectors 2 x 20-pin box headerDimensions (L x H) 96 x 90 mm (3.8" x 3.5")Power Consumption Typical: 5 V @ 180 mA

Max.: 5 V @ 400 mAOperating Temperature 0 ~ 60° C (32 ~ 140° F)Storage Temperature -40 ~ 85° C (-40 ~ 185° F)

Ordering InformationPCM-3718H 100 kS/s, 12-bit Multi. PC/104

Module PCM-3718HG 100 kS/s, 12-bit High-gain

Multi. PC/104 Module PCM-3718HO 100 kS/s, 12-bit Multi. PC/104

Module w/AOADAM-3920 20-pin DIN-rail Flat Cable

Wiring BoardPCLD-780 Screw Terminal Board w/ Two

20-pin Flat CablesPCL-10120-1 20-pin Flat Cable, 1 mPCL-10120-2 20-pin Flat Cable, 2 m

PCM-3813IPCM-3718H/HG/HOPCM-3724

100 kS/s, 12-bit, 32-ch Isolated Analog Input PCI-104 Module100 kS/s, 12-bit, 16-ch PC/104 Multifunction Module

48-ch Digital I/O PC/104 Module

PCM-3813I PCM-3718H/HG/HO

Features48 TTL digital I/O linesSupports dry contact and wet contactKeeps the I/O port setting and DO state after system resetOutput status read-backChannels simulate 8255 PPI mode 0Interrupt triggering, rising/falling edge




Digital OutputChannels 48 (shared with input)Compatibility 5 V/TTLOutput Voltage Logic 0: 0.5 V max. @

6 mA Logic 1: 2.0 V min. @ -6 mA

GeneralBus Type PC/104I/O Connectors 2 x 50-pin box headerDimensions (L x H) 96 x 90 mm (3.8" x 3.5")Power Consumption 5 V @ 90 mAOperating 0 ~ 60° C (32 ~ 140° F) TemperatureStorage Temperature -40 ~ 85° C (-40 ~ 185° F)

Ordering InformationPCM-3724 48-ch Digital I/O PC/104

Module w/ 50-pin CableADAM-3950 50-pin DIN-rail Flat Cable

Wiring BoardPCLD-782B 24-ch IDI Board w/ 20-pin

& 50-pin Flat CablesPCLD-785B 24-ch Relay Board w/ 20-

pin & 50-pin Flat CablesPCL-10150-1.2 50-pin Flat Cable, 1.2 m

PCM-3724

Features32 single-ended or 16 differential analog inputs 12-bit A/D converter, with up to 100 kHz sampling rateProgrammable gain for each input channelAutomatic channel/ gain/ SD scanning Onboard ring buffer (1,024 samples)Isolation protection (2,500 VDC)Software polling, internal or external pacer sampling modes supportedBoardID™ switch


Channels 32 single-ended or 16 differential or combination

Resolution 12 bitsMax. Sampling Rate 100 kS/sRing Buffer Size 1,024 samplesInput Range and PGA Bandwidth

Gain 0.5 1 2 4 8Unipolar N/A 0 ~ 10 0 ~ 5 0 ~ 2.5 0 ~ 1.25Bipolar ±10 ±5 ±2.5 ±1.25 ±0.625Bandwidth 5.0 MHz 5.0 MHz 4.0 MHz 1.3 MHz 0.6 MHz

Input Protect 30 Vp-pInput Impedance 100 MW/10pF (off);

100 MW/100pF (on)Trigger Mode Software polling,

onboard programmable pacer, or external TTL trigger

GeneralBus Type PCI-104I/O Connectors 1 x IDC-40 pinDimensions (L x H) 96 x 90 mm (3.8" x 3.5")Operating 0 ~ 60° C (32 ~ 140° F) Temperature (refer to IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~158° F)

Ordering InformationPCM-3813I 100 kS/s, 12-bit Isolated AI

PCI-104 ModuleADAM-3937 DB37 DIN-rail Wiring

Board




NEW





Channels 16, 5 V/TTLInterrupt Capable Ch. 4

Isolated Digital InputChannels 8Input Voltage Logic 0: 2 V max.


Isolation Protection 2,500 VDC

Opto-Isolator 0.1 ms ResponseInput Resistance 2 kW @ 0.5 W

Digital OutputChannels 16, 5 V/TTLOutput Capability Sink: 8 mA @ 0.5 V max. Source: -0.4 mA @ 2.4 V min.

Isolated Digital OutputChannels 8Output Type Sink (NPN)Isolation Protection 2,500 VDC


Sink Current 200 mA max./channelOpto-Isolator 100 µs Response

GeneralBus Type PC/104I/O Connectors 3 x 20-pin box headerDimensions (L x H) 96 x 90 mm (3.8" x 3.5")Power Consumption 330 mA @ +5 V (typical)

500 mA @ +5 V (max.)Operating 0 ~ 60° C (32 ~ 158° F) TemperatureStorage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95% RH, non-cond.

Ordering InformationPCM-3730 16-ch Isolated DI/O PC/104

Module w/ 20p CablePCL-10120-1 20-pin Flat Cable, 1 mPCL-10120-2 20-pin Flat Cable, 2 mADAM-3920 20-pin DIN-rail Flat Cable

Wiring BoardPCLD-780 Screw Terminal Board w/

Two 20-pin Flat CablesPCLD-785 16-ch Relay Board w/ One

1m 20-pin Flat CablePCLD-885 16-ch Power Relay Board w/

20p & 50p Flat Cables


Channels 8Input Voltage Logic 0: 3 V

Logic 1: 10 V (50 V max.)Isolation Protection 2,500 VDC

Overvoltage 70 VDC

ProtectionOpto-Isolator 25 µs ResponseInput Resistance 4.7 KW

Relay OutputChannels 8Relay Type SPDT (Form C)Contact Rating 30 VDC@ 1.5 A Relay on Time 4 msRelay off Time 4 msLife Span 100,000 min @ 2 A/30 VResistance Contact: 100 MW

Insulation: 1 GW @ 500 VDC

GeneralBus Type PC/104I/O Connectors 1 x 20-pin head for IDI

1 x 50-pin head for relayDimensions (L x H) 96 x 90 mm (3.8" x 3.5")Power Consumption 100 mA @ +5 V (typical)

280 mA @ +5 V (max.)Operating 0 ~ 60° C (32 ~ 158° F) TemperatureStorage Temperature -20 ~ 70° C (-4 ~ 158° F)Storage Humidity 5 ~ 95% RH, non-cond

Ordering InformationPCM-3725 8-ch Relay/Isolated Digital

Input PC/104 Module PCL-10120-1 20-pin Flat Cable, 1 mPCL-10120-2 20-pin Flat Cable, 2 mPCL-10150-1.2 50-pin Flat Cable, 1.2 mADAM-3920 20-pin DIN-rail Flat Cable

Wiring BoardADAM-3950 50-pin DIN-rail Flat Cable

Wiring BoardPCLD-780 Screw Terminal Board w/ Two

20-pin Flat Cables

PCM-3725PCM-3730PCM-3780

8-ch Relay and Isolated Digital Input PC/104 Module

16-ch Isolated Digital I/O PC/104 Module2-ch Counter/Timer with 24-ch Digital I/O PC/104 Module

SpecificationsProgrammable Counter

2 independent 16-bit counters4 independent programmable clock sources (10 M, 1 M, 100 k, 10 k)12 programmable counter modes

Digital InputChannels 24 (shared with output)Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.


Digital OutputChannels 24 (shared with input)Compatibility 5 V/TTLOutput Voltage Logic 0: 0.5 V max. @ 24 mA (sink) Logic 1: 2.4 V min. @ 15 mA (source)

Counter/TimerChannels 2Resolution 16 bitsCompatibility 5 V/TTLMax. Input Frequency 20 MHzCounter Modes 12 (programmable)Interrupt Capable Ch. 2

GeneralBus Type PC/104I/O Connectors 1 x 50-pin box header

1 x 20-pin box headerDimensions (L x H) 96 x 90 mm (3.8" x 3.5")Power Consumption 300 mA @ +5 V (typical)

0.8 mA @ +5 V (max.)Operating 0 ~ 60° C (32 ~ 158° F) TemperatureStorage Temperature -20 ~ 70° C (-4 ~ 158° F)Operating Humidity 5 ~ 85% RH non-cond.

Ordering InformationPCM-3780 2-ch Counter/Timer, DI/O,

PC/104 Module w/CablesPCL-10120-1 20-pin Flat Cable, 1 mPCL-10150-1.2 50-pin Flat Cable, 1.2 mADAM-3920 20-pin DIN-rail Flat Cable


Wiring Board

PCM-3725 PCM-3730 PCM-3780


8

544

10USB DAQ


8DAQ

7Serial Comm. Card

6Device Server

Ethernet Switch

Industrial Monitor


2Touch Panel PC



Fanless Box PC


PAC14

RS-485 I/O15

Ethernet I/O16






PCM-3730IPCM-3753IPCM-3761I

32-ch Isolated Digital I/O PCI-104 Module

96-ch Digital I/O PCI-104 Module8-ch Relay and 8-ch Isolated Digital Input PCI-104 Module

PCM-3753I PCM-3761IPCM-3730I

FeaturesSupports dry/wet contact

Keeps the last output value after system hot reset

Interrupt handling capacity

“Pattern match” and “change of state” interrupt functions


Interrupt output pin for simultaneously triggering external devices

SpecificationsDigital Input/Output

Channels 96 (bi-directional)Compatibility 5 V/TTLInput Voltage Logic 0: 0.8 V max.

Logic 1: 2.0 V min.Output Voltage Logic 0: 0.4 V max.


Source: 2.4 V @ 15 mA

GeneralBus Type PCI-104I/O Connectors 4 x IDC-50 pinDimensions (L x H) 96 x 90 mm (3.8" x 3.5")Operating -20 ~ 70° C TemperatureStorage Temperature -50 ~ 120° C

Ordering InformationPCM-3753I 96-ch Digital I/O PCI-104

Module w/ 50p CablePCL-10150-1.2 50-pin Flat Cable, 1.2 mADAM-3950 50-pin DIN-rail Flat Cable

Wiring BoardPCLD-782B 24-ch IDI Board w/ 20-pin

& 50-pin Flat CablesPCLD-785B 24-ch Relay Board w/ 20-

pin & 50-pin Flat Cables

Features8 Form C type relay output channelsRetained relay output values when hot system resetHigh-voltage isolation on input channels (2,500 VDC)Wide input range (5 ~ 30 VDC)Interrupt handling capability



Logic 1: 5 V min. 30 V max.

Input Current 2.5 mA @ 5 V 15 mA @ 30 V

Input Resistance 2 kW 0.5 WIsolation Protection 2,500 VDC


Interrupt Capable All channelsOpto-isolator 25 µs Response Time

Relay OutputChannels 8Relay Type DPDT, Form CContact Rating 240 VAC @ 0.25 A,

or 30 VDC @ 1 ARelay on Time 5 ms max.Relay off Time 4 ms max.Life Span 1 x 10^7 @ 6 V/100 mAResistance Contact < 50 mWInsulation 1 GW min. (at 500 VDC)

GeneralBus Type PCI-104I/O Connectors 1 x IDC-50 pin,

1 x IDC-20 pinDimensions (L x H) 96 x 90 mm (3.8" x 3.5" )Operating Temperature 0 ~ 60° C (32 ~ 140° F)

(refer to IEC 68-2-1, 2)Storage Temperature -20 ~ 70° C (-4 ~ 158° F)

Ordering InformationPCM-3761I 8-ch Relay/Isolated Digital

Input PCI-104 ModuleADAM-3920 20-pin DIN-rail Flat Cable


Wiring BoardPCL-10150-1.2 50-pin Flat Cable, 1.2 mPCL-10120-1 20-pin Flat Cable, 1 mPCL-10120-2 20-pin Flat Cable, 2 m

FeaturesHigh-voltage isolation on input channels (2,500 VDC)

High output driving capacity


High-voltage isolation on output channels



Logic 1: 5 V min. 30 V max.

Input Current 2.5 mA @ 5 V 15 mA @ 30 V

Input Resistance 2 kW 0.5 WIsolation Voltage 2,500 VDC

Over Voltage 70 VDC

ProtectionOpto-isolator 25 µs Response TimeInterrupt Capable All channels

Isolated Digital OutputChannels 16Output Voltage 5 to 30 VDC

Open Collector Output Sink Current 200 mA max.Isolation Voltage 2,500 VDC

Over Current 1.6 A per 8 channels ProtectionOpto-isolator 25 µs Response Time

GeneralBus Type PCI-104I/O Connectors 2 x 20-pin IDCDimensions (L x H) 96 x 90 mm (3.8" x 3.5")Operating -20 ~ 70° C Temperature Storage Temperature -50 ~ 120° C

Ordering InformationPCM-3730I 32-ch Isolated Digital I/O

PCI-104 ModuleADAM-3920 20-pin DIN-rail Wiring

BoardPCL-10120-1 20-pin Flat Cable, 1 mPCL-10120-2 20-pin Flat Cable, 2 m

NEW NEW NEW


Features

PCI-1671UP

IntroductionThe PCI-1671UP IEEE-488 interface converts any PCI bus personal computer into an instrumentation control and data acquisition system. Connect up to 14 instruments using standard IEEE-488 cables such as the PCL-10488-2, 2 meter IEEE-488 interface cable. The PCI-1671UP transfers data over the GPIB at rates in excess of 1.5 million bytes per second using the maximum IEEE-488 specification cable length (2 meters times the # of devices). A 1,024-word FIFO buffer and the advanced REP-INSW ISR data transfer method provide the horsepower required to then transfer the data between the GPIB board and the host computer. The high-speed state machine also provides byte-to-word packing and unpacking, and because words carry twice the information that bytes do, packed data requires fewer bus cycles to transfer the same GPIB information.

The PCI-1671UP adheres to ANSI/IEEE Standard 488-1978. Often referred to as the IEEE-488.2 bus, GPIB bus or HP-IB bus, the GPIB (General Purpose Interface Bus) is a standard for instrumentation communication and control for instruments from manufacturers the world over. The GPIB provides handshaking and interface communications over an 8-bit data bus employing 5 control and 3 handshake signals. Equipped with PCI-1671UP, a personal computer can control GPIB instruments, gather data from GPIB test equipment, or become a data acquisition station in a GPIB system.

IEEE 488.2 Standard interface

Complete Talker/Listener/Controller

Industry standard 32-bit PCI bus

Data transfer rates over 1.5 MB/s

1,024-word FIFO buffer

High-Speed State Machine Bus Manager

7 Interrupt lines, shared interrupt capability

Transparent interrupt enabling/disabling

Includes GPIB-Library software

Low profile MD1 size

SpecificationsGPIB

Compatibility IEEE 488.1, 488.2GPIB Transfer Rate 1.5 MB/sOS Support Windows® 2000/XPLibrary Support Visual C++®, Borland C++ Builder®, LabWindows/CVI,

Visual Basic®, Delphi®, LabVIEWMax. GPIB Connections 15

GeneralBus Type Universal PCI V2.2I/O Connectors 1 x 24-pin IEEE 488Dimensions (L x H) 120 x 64 mm (Low profile MD1)Power Consumption 5 VDC @ 375 mAOperating Temperature 0 ~ 60° C (32 ~ 158° F) @ 0-90% RHStorage Temperature -40 ~ 100° C (-40 ~ 212° F) @ 5-90% RHOperating Humidity 0 ~ 90% RH, non-condensing

Ordering InformationPCI-1671UP High-perform. IEEE-488.2 Interface PCI CardPCL-10488-2 IEEE-488 Cable, 2 m

IEEE-488.2 Interface Low Profile Universal PCI Card

Data Acquisition Boards - Esis€¦ · Operating system used 2. User programming expertise 3....

Documents

Transcript of Data Acquisition Boards - Esis€¦ · Operating system used 2. User programming expertise 3....