D5 & D6C Crawler S/n 98J1 & Up S/n 17R1 & Up...Caterpillar D5 | D6C Crawler Operators Manual Author:...
5
Operator’s Manual Operator’s Manual THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF CATERPILLAR OR IT’S SUCCESSORS. CATERPILLAR AND IT’S SUCCESSORS ARE NOT RESPONSIBLE FOR THE QUALITY OR ACCURACY OF THIS MANUAL. TRADE MARKS AND TRADE NAMES CONTAINED AND USED HEREIN ARE THOSE OF OTHERS, AND ARE USED HERE IN A DESCRIPTIVE SENSE TO REFER TO THE PRODUCTS OF OTHERS. D5 & D6C Crawler S/n 98J1 & Up S/n 17R1 & Up CT-O-D5 98J+
Transcript of D5 & D6C Crawler S/n 98J1 & Up S/n 17R1 & Up...Caterpillar D5 | D6C Crawler Operators Manual Author:...
Op
era
tor’
s M
an
ua
l
Operator’s Manual
THIS IS A MANUAL PRODUCED BY JENSALES INC. WITHOUT THE AUTHORIZATION OF
CATERPILLAR OR IT’S SUCCESSORS. CATERPILLAR AND IT’S SUCCESSORS
ARE NOT RESPONSIBLE FOR THE QUALITY OR ACCURACY OF THIS MANUAL.
TRADE MARKS AND TRADE NAMES CONTAINED AND USED HEREIN ARE THOSE OF OTHERS,
AND ARE USED HERE IN A DESCRIPTIVE SENSE TO REFER TO THE PRODUCTS OF OTHERS.
D5 & D6C Crawler
S/n 98J1 & Up
S/n 17R1 & Up
CT-O-D5 98J+
ERPILLAR
@~®[f(ill~O@ITiJ U¥1J (ill ITiJ (ill (ill ~ D5&D6 Special Application Tractors
98J1-Up 17R1-Up
TABLE OF CONTENTS
06 Special Application Tractor. . . . . . . . . . . . . . .. 3
Safety ........ : . . . . . . . . . . . . . . . . . . . . . . . . . . .. 4
Symbol Identification . . . . . . . . . . . . . . . . . . . . . . .. 6
Operator's Compartment. . . . . . . . . . . . . . . . . . . .. 9
Controls. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 11
Before Starting. . . . . . . . . . . . . . . . .. . . . . . . . . . .. 12
Starting the Engine ......................... 14
After Starting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .. 18
Moving the Tractor .......................... 20
Parking the Tractor .......................... 25
Operating Adjustments ....................... 26
Operating Techniques ....................... 32
Shipping Hints .............................. 34
2
BEFORE STARTING
1. Check diesel engine crankcase oil level. Oil level should be above FULL mark on gauge.
3. Check transmission, bevel gear, flywheel clutch, steering clutch and hydraulic system oil level. Oil should show on gauge.
5. Check air cleaner service indicator. Have air cleaner serviced if red piston is locked in the visible position.
12
2. Check coolant level. Maintain level to within % inch' (1 em) of the bottom of fill pipe.
4. Check fuel level.
6. Check for free movement of controls.
Beam Adjustments
NOTE Beam. must be parallel to ground when implement is at desired penetration depth.
2. Shorten screws to increase penetration.
1. Lengthen screws to decrease penetration.
NOTE Do not lengthen screw more than 5% inches (140 mm).
3. Lock handles.
Removing Tool Bar Beam Assembly
1. Put 18 inch (45 cm) blocks under beam assembly.
27
2. Remove adjusting screw, cotter and pin. Remove draft member cotter and pin.
3. Drive tractor away.
