d - tv antenna & systems
-
Upload
radio-parts -
Category
Documents
-
view
168 -
download
2
Transcript of d - tv antenna & systems
2010 11
TV ANTENNA &SYTEMS
TV ANTENNAS 134VHF 134UHF 134UHF VHF COMBO 135FM 136INDOOR 137CARAVAN 137SATELLITE 137
TV ANTENNA ACCESS. 138MASTHEAD AMPS 138AMP POWER PACKS 140DISTRIBUTION AMPS 141SPLITTER AMPS 141BALUNS & ATTENUATORS 142SPLITTERS & TAPS 142DIPLEXER & TRIPLEXERS 143SATELLITE ACCESS. 144
TV HARDWARE 144MASTING 144MOUNTING 144ROTATOR 147SATELLITE HARDWARE 147
133
CATALOGUE 2010 - 2011134
TV ANTENNA & SYSTEMS
TV ANTENNAS
VHF & UHF ANTENNAS
Designed and tested for digital/analogue reception
VHF YAGI ANTENNA INNER METRODOSS
00727055 V307
Designed and tested for digital/analogue reception
F-Type High Performance Balun Snap out reflectors Stainless Steel screws on connection points
VHF YAGI ANTENNA OUTER METRODOSS
00643735 V310
VHF YAGI ANTENNA OUTER FRINGEDOSS
00643740 V318
VHF DIGITAL ANTENNA HILLSHILLS
00681262 DY6-612
00681268 DY14
6 element
14 element
Digital and analogue compatibility F Type connectors for better shielding and more reliable connections
Rectangular galvanised steel boom construction provides element alignment
Powder coated boom for longer life and improved aesthetics
UV stable plastics for durability under harsh Australian conditions
Australian designed and manufactured
Suitable for reception of horizontal or vertical polarised transmissions
VHF
Channels 6 to 11 High gain 16 element aerial
Can be mounted horizontally, vertically or stacked
Ribbon cable connection 300 Forward gain 10.5-12.5 dB Front to back ratio: 11-16dB
VHF PHASED ARRAY ANTENNAHILLS
00643400 CA16
Deluxe wide band VHF antenna suitable for all VHF channels 1-11 & FM
Good directional properties coupled with superior anti-ghost design
Ellipsoidal anodised boom-anodised elements and EFC Low-loss 75 balun.VHF Ch. 1-11
Popular choice for exceptional frontal and rear anti-ghost properties where a combination aerial is not suitable
Forward Gain: 2-4dB Front to back ratio: 9-14 dB 75 coax connection
VHF WIDEBAND ANTENNA 7 ELEMENTHILLS
00643616 EFC2
Engineered for Digital VHF Wideband Antenna Reinforced for fringe & inner fringe reception
For areas where more directivity is required
VHF Ch: 2-12 75Ω F type coax connection Forward gain 1-11dB F/B ratio: 14-17dB
VHF DIGITAL ANTENNAHILLS
00643725 DL3
GAIN LIFT FOR CA16HILLS
00643472 16CH2
Gain lifter kit can be added to improve Ch2 reception
Forward gain 6.3 dB Front to back ratio: 16dB
UHF
Premium Metropolitan Log periodic Antenna designed for flexible installations on a budget for VHF/UHF digital broadcast reception
VHF/UHF ANTENNA LOG PERIODICDOSS
00727360 CLP
Can be mounted vertical or horizontal as required
UHF ANTENNA LOG PERIODICDOSS
00727365 CLP4/5
Premium UHF Antenna designed for digital broadcast reception
UHF ANTENNA INNER METROPOLITANDOSS
00727350 UWX16
Premium UHF Antenna designed for digital broadcast reception
UHF ANTENNA OUTER METROPOLITANDOSS
00727355 UWX34
Premium Metropolitan UHF Antenna ideal for digital broadcast reception
UHF HIGH GAIN DIGITAL ANTENNADOSS
00727310 UW20
Designed and tested for digital/analogue reception
UHF ANTENNA MESH REFLECTORDOSS
00727340 SX43M
Designed and tested for digital/analogue reception
UHF ANTENNA MESH REFLECTORDOSS
00727345 SX91M
Anti-ghosting antenna for outer areas
Superior Gain(16.5dB) High front to back ratio (30dB)
UHF ANTENNA OUTER AREA PHASEDDOSS
00727370 UPA2
UHF WIDEBAND TRIBEAM ANTENNADOSS
00727380 UTR1
Compact robust 9 element design, easy to assemble, built to the highest electrical standards
Inner fringe model Balun included Forward Gain: 8-13dB F/B ratio:17-20dB Impedance: 75
CH21-69 UHF WIDEBAND ANTENNAHILLS
00720664 TMX16WB
RADIO PARTS GROUP 135
TV ANTENNA & SYSTEMS
D
UHF VHF COMBO ANTENNAS
Hills TMX18B4 & TMX18B5 Band 4 & Band 5
Antennas are compact robust 11 element design
Easy to assemble, built to the highest electrical standards
Band 4 UHF Channels: 28~35 Band 5 UHF Channels: 36~69 Fringe signal model Balun included Forward Gain: 12.5-15dB F/B ratio: 15-24dB Impedance: 75Ω
CH21-35 UHF BAND 4HILLS
00720678 TMX18B4
00720682 TMX18B5
Band 4
Band 5
Digital ready UHF TV antenna Medium Gain designed for Channels 21 to 50
Printed Circuit Board baluns to provide optimal impedance matching and mechanical characteristics.
F Type connectors Unique cross shaped double elements Provides higher gain in a more compact antenna
UV stable plastics Simple assembly Compact neat and unobtrusive design
CH21-50 UHF BAND 4HILLS
00720690 TMX20B4P
Compact, robust 18 element design Easy to assemble Built to the highest electrical standards
Wideband UHF Channels: 28~69 Fringe signal model Balun included Forward Gain: 10-17dB F/B ratio:15-22dB Impedance: 75 Note: Shown with optional FB603836 centre support brace
CH28-69 UHF WIDEBANDHILLS
00720720 TMX34WB
CH28-42 UHF BAND 4 ANTENNAHILLS
00720812 SF91B4P
High gain Band 4 Plus model Ch 28-50 Designed for poor reception areas Quad-X design for extra signal strength Pre-assembled in carton Mesh screen reflector Exceptional anti-ghost qualities Forward Gain: 13-18dB F/B ratio:19-22dB Balun included Impedance: 75Ω
Compact robust design, easy to assemble, built to the highest electrical standards
18 Unique cross shaped double elements for extra strength
Super Fringe signal model Digital and Analogue compatible Suits Channels 28-69 F type connection for better shielding and more reliable connection
Forward Gain:10-17dB Front to Back ratio:15-22dB Impedance: 75 Ohm Note: Centre Brace is Included
CH21-69 UHF WIDEBAND ANTENNAHILLS
00720800 SFX91WB
UHF PHASED ARRAY ANTENNAHILLS
00720483 HUNTER
High gain, excellent front-to-back ratio. For vertical & horizontal polarization
UHF channels 21 - 69 High gain, excellent front-to-back ratio
For vertical & horizontal polarization 10 Tilt facility in horizontal mode Forward Gain:11.4-14.4dB Front to Back ratio:17-19dB Balun included Impedance: 75
UHF phased array antenna with integrated director
Digital & Analog Compatible Channels: 21 - 69 UHF Optimized wide band PCB balun Sealed housing with integral F connector
Robust construction Quick horizontal or vertical mounting
UHF PHASED ARRAY ANTENNAHILLS
00720486 ULTIMAX36
UHF VHF COMBO
VHF/UHF DIGITAL ONLY ANTENNADOSS
00727335 CD14
Stainless Steel screws on connection points
VHF/UHF DIGITAL ANTENNA INNERDOSS
00727320 CD15
VHF/UHF DIGITAL ANTENNA OUTERDOSS
00727325 CD19
F-Type High Performance Balun
F-Type High Performance Balun
Solid-built, high quality, premium VHF/ UHF Antenna ideal for digital broadcast reception
F-type PCB high performance balun UV stabilised plastics 12mm extruded aluminium boom Snap-out reflections Ideal for outer-metropolitan areas VHF/ UHF: 2-12/ 28-40 Back to Front Ratio: >14 dB Front to Back Ratio: >12 dB
VHF/UHF PREMIUM ANTENNADOSS
00727302 CD40
VHF/UHF CROSS POLARISEDDOSS
00727375 CDX19
Solid-built, high quality, premium cross polarity Antenna
Spectramax UHF/VHF Combination antenna
For VHF channels 6-12 inclusive (4 elements)
UHF channels 28-69 (10 elements) For prime signal areas Forward gain:6-8dB VHF 8-13dB UHF Front to back ratio:14-19dB VHF, 11-17dB UHF
Features double sided UHF elements and Trigonal reflector to improve performance
F Type connectors enable better shielding and more reliable connection
VHF/UHF WIDEBAND ANTENNAHILLS
00727007 SMX14WB
For Ballarat, Gippsland, Launceston, SW & W NSW
4 Element VHF Ch. 6 - 12 The UHF section is a 10 element antenna with optimum performance on channels
VHF Channels 6-12 UHF Channels 28-50 75 ohm coax connection Forward gain: 6-8dB VHF, 8-13dB UHF
Front to back ratio: 14-19dB VHF, 11-17dB UHF
VHF/UHF BAND 4 DIGITAL ANTENNAHILLS
00727008 SMX14B4P
VHF/UHF BAND 4 DIGITAL ANTENNAHILLS
00727009 SMX24B4P
Digital & Analogue compatibility VHF Ch: 6-12 UHF Ch: 28-50 Gain (dB): VHF: 7-9 UHF: 8-16 F-B Ratio (dB): VHF: 14-17 UHF: 14 - 18
CATALOGUE 2010 - 2011136
TV ANTENNA & SYSTEMS
Y3/FM With Balum VHF Regional Antenna
VHF channels FM, 3, 4 & 5 3 Elements Prime Signal Antenna Forward gain 5dB Front to back ratio 15dB
Premium FM Antenna designed for crystal clear reception of your favourite FM broadcasts
FM
FM RADIO ANTENNA / AERIALHILLS
00442056 Y3FM
FM RADIO ANTENNA / AERIALDOSS
00442060 FM3
UHF VHF COMBO ANTENNAS | FM
VHF/UHF WIDEBAND ANTENNAHILLS
00727012 SMX24WB
Double sided UHF elements and Trigonal reflector to improve performance.
VHF Ch: 6-12 UHF Ch: 28-69 Gain (dB): VHF: 7-9 UHF: 8-16 F-B Ratio (dB): VHF: 14-17 UHF: 14 - 18
A compact antenna designed for prime signal locations
HD Elements/ Galv. Steel boom F Type connector/ P.C Board Balun VHF channels 2-12 - UHF 28-40 Suitable for Melbourne, Sydney, Brisbane, Adelaide and Perth
Forward Gain VHF:4-9 Forward Gain UHF:9-11Fwd/Back Ratio VHF:10-14
Fwd/Back Ratio VHF:11.5-15 NOTE: Economy Version with single element reflector, ferrite balun and non-powder coated beam
VHF/UHF METRO ANTENNAHILLS
00720350 OMX100P
00720351 OMX100
Optimax 100 PLUS
Optimax 100 Economy
VHF/UHF BAND 4 METROHILLS
00720354 OMX300
VHF/ UHF ANTENNAHILLS
00720387 OMX400P
HD Elements/ Galv. Steel boom F Type connector/ P.C Board Balun Forward Gain VHF:3-9 Forward Gain UHF:9-15 Fwd/Back Ratio VHF:10-15 Fwd/Back Ratio VHF:15-19
Suitable for analogue/digital signal Suitable for inner fringe areas Gain:VHF: 5-10dB UHF:10-13dB F-B Ratio:VHF:10-14dB UHF:10.5-15dB
VSWR:VHF 2:1- UHF 1.6:1
Galvanised steel boom Clam shell insulators 1/2 inch extruded aluminium elements provide a heavy duty construction to withstand harsh weather conditions and wildlife.
Solid rivet construction for durability F Type connectors Extra UHF elements Ultrasonically sealed balun housing Improved trigonal reflector VHF channels 2-12 - UHF 28-40 Forward Gain VHF:6-11 Forward Gain UHF:13.5-15 Fwd/Back Ratio VHF:10-15 Fwd/Back Ratio VHF:15-19
VHF/UHF OUTER METRO ANTENNAHILLS
00720391 OMX450P
VHF/UHF FRINGE ANTENNAHILLS
00720400 OMX550P
VHF/UHF OUTER FRINGE ANTENNAHILLS
00720410 OMX650P
Strong Galvanised steel boom for a more rigid antenna
Designed for improved gain in fringe areas
Suitable for analogue and digital signals
VHF/UHF CROSS POLARISED SEEKERHILLS
00727005 UV13
Designed for regions where UHF and VHF channels are in alternate polarities. (VHF vertically/ UHF is horizontally)Aluminium boom with unique dual rear section for extra strength
Clam shell insulators ½" extruded aluminium elements F Type connectors
VHF/UHF CROSS POLARISED SEEKERHILLS
00727010 UV16C
For Bendigo, Swanhill (Vic) and Mt Conobolis (NSW)
Receives VHF Channel 1 & 6 to 11.
For use where VHF is vertical and UHF is horizontal
For Bendigo, Swanhill (Vic) and Mt Conobolis (NSW)
Receives VHF Channel 1 & 6 to 11 75 ohm coax connection
VHF/UHF CROSS POLARISED SEEKERHILLS
00727015 UV19WB
PLATINUM HIGH DEFINITIONHILLS
00720348 PHD2
PLATINUM HIGH DEFINITIONHILLS
00720305 PHD1
Suitable for channels 6-12 & 28-36 Capital City Digital Channels Reduce Impulse Noise Ultrasonically Sealed PCB F type housing
Clamshell insulators to provide positive element locking
Compact and lightweight Quick and easy site installation Designed and made in Australia for Australian conditions
VHF Channels: 6-12 VHF Gain: 4-6dB VHF F/B Ratio: 11-13dB UHF Channels: 28-36 UHF Gain: 9-11dB UHF F/B Ratio: 14-18dB
13 Element antenna with 'F" type balun fitted Weight: 4.79kg
Gain: B1- 4.5dB / B2-4dB / B3-6dB / UHF-11.5dB
Suitable for channels 6-12 & 28-36 Capital City Digital Channels Reduce Impulse Noise Ultrasonically Sealed PCB F type housing
Clamshell insulators to provide positive element locking
Compact and lightweight Quick and easy site installation
VHF/UHF DIGITAL ANTENNAMATCHMASTER
00727301 MD13P
RADIO PARTS GROUP 137
D
TV ANTENNA & SYSTEMS
Adjustable polarity - simply unscrew 2 wing-nuts to easily convert from vertical to horizontal polarity
Round: 73cm Satellite Dish Supplied with hardware Grey Colour, powder coated One LMBF support arm
Suitable for Caravans, Boats, and mobile homes Suitable for Digital TV applications Omni-directional 3W Antenna Suitable for VHF/FM/UHF (CH 1-12 and 21-69) inPrime/Medium reception Areas
High gain (Up to 36dB) with adjustable gain amplifier box Two TV outputs provided
Built-in low noise circuit Comes with 12m and 1.5m Flyleads Water-proof housing and connection Impedance: 75Ohm Power Supply: 240VAC, 50Hz or 12VDC @100mA Size: 490 x 490 x 120 (LxWxH)
00769002 FL2BS12F
00769004 FL2BS12
00769009 FMFILTF
00769010 BC44264
00604515 C216
12DB LOW BAND VHF FILTER
12DB LOW BAND VHF FILTER
FM BAND REJECTION FILTER 'F'
FM TRAP FILTERHILLS
INDOOR
RABBIT EARS INDOOR
In line trap connects to aerial socket on TV set and filters out unwanted FM interference
Twin Telescopic rods with swivel in plastic base
Direct replacement for antennas on many TV sets
VHF/UHF INDOOR AERIAL
00605015 IA313
VHF/UHF & FM INDOOR AERIAL
00605018 FMA78
INDOOR AMPLIFIED ANTENNADOSS
00605020 SV9100
CARAVAN
UFO BOAT & CARAVAN ANTENNAANTSIG
00727142 AP515
VHF/UHF COMBO CARAVAN ANTENNAPHASELINK
00727155 RV30
VHF/UHF CARAVAN WIDEBANDDOSS
00727260 CMX11CA
Suitable for all channels UHF and VHF sections can be adjusted up/down or rotated for best reception
Complete with 75 ohm coaxial lead & plug
Adjustable Telescopic Rods Attenuator and fine tuning pot
75Ω coaxial cable and PAL plug
Rubber suction feet for greater stability
Designed to receive standard TV and FM radio signals. Generally these antennas work best when they are within a 50KM radius of a transmitting tower
0-30dB Signal Gain Gain Control Dial 88-108mHZ FM Ch: 1-69 Bandwith
Designed specifically for mobile applications This Australian made kit comes complete with power booster, power injector and 240/12v plug pack
Covers channels 6 ~ 69 Built in signal booster is engineered for touring caravanners and provide deep fringe performances on all VHF and UHF channels
Two telescopic dipoles Built-in amplifier
SATELLITE
73CM ROUND SATELLITE DISH
01001040 HSD73
High gain portable outdoor TV Antenna. Cross folded dipoles for perfect reception in all directions. AP515 is supplied with fully adjustable gain controller. The Antenna amplifier can be supplied either from the AC mains or DC power adaptor (not included). AP515 Antenna is the perfect choice for people on the move wanting to get the best TV signal anywhere around Australia.
INDOOR | CARAVAN | SATELLITE
CATALOGUE 2010 - 2011138
TV ANTENNA & SYSTEMS
For weak signal areas that require boosting Very low noise: VHF < 2 dB, UHF < 2.5 dB High gain on required channel group : 32dB High output capacity (116dBuv on 1 Channel, 100 dBuV on 20 Channels)
Good impedance matching (RTR/V SWR) Built in filter rejects FM Band II Lightning & static protection built in Filter rejects cellular phone interference Gold plated internal links to ensure reliable contact UHF Only 470-820MHz Use with UHF antenna only Gain: UHF 32dB Requires PSU2C power supply
Satellite Dish KU Band 65cm Supplied with hardware Grey colour, powder coated One LMBF support arm
Input Voltage: AC 220-240V~ - 50Hz Output Voltage: DC 36V Maximum Current: 2.2A Power Consumption: Max. 70W - Stand By 5W
Antenna Width: 810 mm Antenna Height: 920 mm Offset Angle: 28 Aperture Efficiency: 75% [email protected] GHz Ku-Band: 39.8 dB
Antenna Width: 1200 mm Antenna Height: 1350 mm Offset Angle: 27.3 Aperture Efficiency: 80% [email protected] GHz Ku-Band: 43 dB
Large dish for C-band reception. Mesh reflective material for low wind resistance
Type: 4 section Operating Frequency: 1.0-12.75 Ghz
Low voltage supply suits Hills "A" series Mast Head Amplifiers
Powered via 240VAC mains lead
65CM OBLONG SATELLITE DISH
01001045 19AA65
85CM KU BAND SATELLITE DISHSTRONG
01001055 SD85
120CM KU BAND SATELLITE DISHSTRONG
01001065 SD120
2.7MT C-BAND SATELLITE DISHSTRONG
01001110 SRTD7.5E
LOCKING BAR FOR FIXED POSITIONSTRONG
01001130 STRBAR
SATELLITE DISH POSITIONERSTRONG
01001140 SRTDDP2
24" SAT DISH CONTROL ACTUATORSTRONG
01001150 SRTA24B
TV ANTENNA ACCESS.
MASTHEAD AMPS
UHF/ VHF MASTHEAD AMPLIFIERHILLS
00760086 PSU2C
VHF ONLY MASTHEAD AMPLIFIERHILLS
00760087 AVA
UHF ONLY MASTHEAD AMPLIFIERHILLS
00760088 AUA
VHF AMPLIFIER UHF PASS THROUGHHILLS
00760089 AVPU
UHF AMPLIFIER VHF PASS THROUGHHILLS
00760092 AUPV
Same features as AUA but with amplify UHF pass VHF, use with separate or combined VHF/UHF antenna
Gain: UHF-30dB/ VHF-3dB Requires PSU2C power supply
For use in areas where signals are weak and require boosting. Mast Head Amplifier for domestic installations or as a pre -amplifiers in MATV (Multi-Outlet) Systems
For use in areas where signals are weak and require boosting. Mast Head Amplifier for domestic installations or as a pre -amplifiers in MATV (Multi-Outlet) Systems
ACCESSORIES
RADIO PARTS GROUP 139
D
TV ANTENNA & SYSTEMS
Low noise masthead amplifiers Variable Gain: UHF 24 ~ 34dB/ VHF 18 ~ 28dB Power through option (B link ) Max output 2 ch 109dBuV Noise figure: 3dB Inputs 2 x 75 ohm
Complete with 15V AC Power Supply Pal Type Injector
FM Rejection Different Voltage Selection
Adjustable Gain Switchable Inputs
Weatherproof Case Power LED Indicator Cellular Notch Filters
The MHU24G is a low noise masthead amplifier designed to amplify UHF television signals by up to 24dB and diplex VHF signals with no gain via separate UHF/VHF aerials
A UHF gain control allows up to 10dB variance of UHF amplification
Frequency Range UHF: 470 - 860 MHz Nominal Gain UHF Min/Max: 14/24dB Output level, UHF, 1dB Compression: 120dBuv Noise figure UHF at Min/Max. Gain: 4/ 2.5dB Typ Frequency Range VHF: 44 - 230MHZ Gain at VHF: -0.75dB Typ Operating Voltage, Nominal: 17.5V AC or 14VDC MHU24GP includes PSK08 power supply PSK08
MULTIPURPOSE MASTHEADSHIELDED AMPLIFIERS - KINGRAY
Amplifiers are based on a new concept of convergent technology. The characteristics of the IC selected provided a noise figure that is lower than any other product currently on the market and an output figure that surpasses most distribution amplifiers
The MDA is a multipurpose amplifier that is ideal for our digital and analogue environment. Whether the unit is used as a Masthead of Distribution Amplifier the low noise figure, capacity for multiple channels with low distortion and a high output provides a solution to all installation and is proven especially effective in digital problem reception areas
All models include PSK06 power supply
Designed specifically to provide versatile amplification of broadband television signals. The amplifier comprises of two separate RF circuits, one for each band VHF and UHF. For each band there are two-amplifier stages, a low-power low-noise preamplifier, followed by a more powerful stage
Switchable Gains Gain Controls Improved Noise Figure Die-Cast Housing 1 or 2 inputs Power On Indication Pager/ Cellular/ FM Filters Earth Point Attachment Weather Proof Case
UHF/ VHF MASTHEAD AMP KITHILLS
00760093 A2APSU4P
UHF/VHF 'F' TYPE MASTHEAD AMPHILLS
00760150 MHQAMP
MASTHEAD BOX WITH STRAPKINGRAY
00760806 MHBP
24DB UHF MASTHEAD AMP KITKINGRAY
00760810 MHU24GEP
UHF MASTHEAD AMPLIFIER VHF DIPLEXERKINGRAY
00760811 MHU24GE UHF Only00760813 MHW24GE Wideband00760812 MHW24GEP Wideband with Power Supply
Hinged lid with locking screw Mast or wall Mounting Neoprene sealing strips Incl. 290mm fixing strap
A low noise masthead amplifier designed to amplify VHF channels 6-12 by 26-44dB and UHF channels 28-69 by 0-10dB.
Suitable power supplies: PSK08/F - 17.5 V AC, 100 mA PSK06/F - 14 V DC, 150 mA
UHF/VHF MASTHEAD AMPLIFIERSKINGRAY
DIGITAL TV SHIELDED MASTHEAD AMP
00760450 MDA20H
'F' Type, single input digital TV fully shielded masthead distribution amplifier designed to amplify 174-860 MHz
ANALOGUE & DIGITAL TV MASTHEAD AMP
00760455 MDA20L
F Type, single input fully shielded analogue & digital TV masthead distribution amplifier designed to amplify 44-860 MHz
UHF ONLY SHIELDED MASTHEAD AMP
00760460 MDA20U
'F' Type, single input UHF only fully shielded masthead distribution amplifier designed to amplify 470-860 MHz
24DB ECONOMY 'F' TYPE MASTHEADKINGRAY
00760824 MHW24FE
Non-shielded F type Masthead Amplifier Max Gain: VHF: 22 - 24 dB UHF: 24 dB Noise Figure: VHF: <2 dB UHF: <2.5 dB Power Supply not included Output Figure: 105 dB
F-Type Connections Frequency Response: Band 1: 45 - 75 MHz | 18 dB FM Band: 88 - 108 MHz | 0 dB Band 3: 174 - 230 MHz | 21 dB Band 4 & 5: 520 - 820 MHz | 24 db Notch Filters: Pager 148 MHz | Cellular >900 MHz Maximum Input/ Output: 78/ 104 dBµV Noise Figure: <3.0 dB Hum Rejection: >110 dB Includes power supply/ injector (PSU4P)
Provides "Digital Compatible" Masthead Amplification of broadband television signals
DIGITAL MASTHEAD AMPHILLS
00769011 LNDA-PSU4P
ACCESSORIES
0076086824~34dB MHU34G UHF Only0076087924~34dB MHW34G Wideband0076081628~69dB MHU34GP
UHF Only with Power Supply
0076081724~34dB MHW34GP
Wideband with Power Supply
0076081824~34dB MHW34GDP
Wideband with Power Supply in Blister Pack
CATALOGUE 2010 - 2011140
TV ANTENNA & SYSTEMS
'F' TYPE VHF/UHF MASTHEAD AMPLIFIERSKINGRAY
Low noise F type masthead amplifier for VHF & UHF Variable Gain UHF: 24 ~ 34dB VHF: 18 ~ 28dB Noise figure: 3dB Inputs 2 x 75 ohm
44DB VHF MASTHEAD AMPLIFIERKINGRAY
00760881 MHV44HLG
A low noise masthead amplifier designed to amplify VHF channels 6-12 by 26-44dB and UHF channels 28-69 by 0-10dB.
Suitable power supplies: PSK08/F - 17.5 V AC, 100 mA PSK06/F - 14 V DC, 150 mA
The MHU44G Amplifier has a 10dB Midstage gain control to vary the gain of UHF channels (28-69) between 34dB & 44dB. The Power Pass Link allows power to pass from the output port to the U/V input port for an additional masthead amplifier if required.
Variable Gain: 520~860MHz - 34-44dB Voltage Range: 17.5V AC/12-14V DC Current: 100mA PSK08 P/Supply not Supplied
44DB UHF MASTHEAD AMPKINGRAY
00769012 MHU44G
ACCESSORIES
00760820 MHW34F Wideband Top Only
00760819 MHW34FPWideband with Power Supply
00760822 MHW34FSShielded Wideband Top Only
00760821 MHW34FSPShielded Wideband with Power Supply
AMP POWER PACKS
Output 1 x 75 OHM PAL Injector Voltage: 240V to 9VDC Max Current 200mA
9V DC 200MA POWER SUPPLYKINGRAY
00760730 PSK01
Active antenna power supply, Mains to 12 VDC @ 20mA
Powers Phaselink boosted antennas via coaxial cable
PAL type Antenna -In, TV- out sockets.
POWER SUPPLY
00761016 ELV12V
Output 1 x 75 OHM PAL Injector Voltage: 240V to 14VDC Max Current 150mA
14V DC 150MA POWER SUPPLYKINGRAY
00760745 PSK06
Output 1 x 75 OHM F-Type Injector
Voltage: 240V to 14VDC
Max Current 150mA
14V DC 150MA POWER SUPPLYKINGRAY
00760747 PSK06F
Output Type: 1 x 2.5mm DC Plug Voltage: 240VAC to 15V DC Max Current: 1.7A
15V DC 1.7AMP POWER SUPPLYKINGRAY
00760760 PSK18KR
Output 1 x 75 OHM PAL Injector Voltage: 240V to 17.5VAC Max Current 100mA
Output 1 x 75 OHM F-Type Injector Voltage: 240V to 17.5VAC Max Current 100mA
Output Type: 1 x 2.5mm DC Plug
Voltage: 240VAC to 18V DC Max Current: 300mA
17.5V AC 100MA POWER SUPPLYKINGRAY
00760750 PSK08
17.5V AC 100MA POWER SUPPLYKINGRAY
00760752 PSK08F
18V DC 300MA POWER SUPPLYKINGRAY
00760755 PSK18S
Output 1 x 75 OHM PAL Injector Voltage: 240V to 22VAC Max Current 100mA
22V AC 100MA POWER SUPPLYKINGRAY
00760735 PSK02
RADIO PARTS GROUP 141
D
TV ANTENNA & SYSTEMS
Amplify TV Signals 0-69 1 Input with 4 Outputs 12dB Gain F type Connections Local & Remote Powering Power through to masthead amplifier
The DW42 has been designed specifically for all digital Free To Air requirements utilising three separate midstage gain controls adjustable by 20dB each, using hybrid bipolar technology.
44-140MHz 35dB Maximum 174-300MHz 37.5dB Maximum 470-860MHz 40dB Maximum Separate inputs for VHF and UHF or combined Shielded construction High output capability Surge diodes for storm & static protection
Two inputs: VHF/UHF or combined with separate gain controls
Separate VHF and UHF Inputs with 1 Output
Built in filter prevents FM radio interference, as well as minimising interference from pagers and some cellular phones
DISTRIBUTION AMPS
27DB DISTRIBUTION AMPLIFIERHILLS
00760061 MINILINK25
33DB DISTRIBUTION AMPLIFIERHILLS
00760065 MAXILINK35
33DB DISTRIBUTION AMPLIFIERHILLS
00760066 MAXILINK35F
34DB 'F' TYPE DISTRIBUTION AMPHILLS
00760070 HTA234
Output 1: Single output for maximum output level Output 2: 2 outputs allows via in-built splitter Incorporating a dual function SLOPE/GAIN control Gain control: 1x Out: 27dB , 2x Out: 21dB Gain Gain adjustment: Variable: 21 to 28dB In-built CB & Cellular phone filters
For use in small to medium sized projects Two inputs: VHF/UHF or combined Frequency: 45 to 860MHz Gain: VHF 33 dB, UHF:36dB (-10dB /-8dB Adjustable) Output level dBuV (2 Channels): VHF 117/ UHF 115 | 6 Channels: VHF 110 The KR001 is a 19" sub rack or reversible wall
mount designed to rack mount and combine Kingrays new professional range of commercial products
The DW32 is a Free-to-Air distribution amplifier for use in MATV multiple dwelling applications
Single or combined VHF/ UHF inputs
Separate VHF/UHF gain controls
In-built slope 30dB test point Local or remote powering options Frequency Range: 44-230 / 520-860 MHz Gain: 27dB - 32dB (Sloped) Noise Figure: <5dB Output Level: 112dBuV DIN45004B @ (-60dB IMR) Return Loss: >10dB Gain Control Range: 10dB VHF, 10dB UHF (mid stage)
32DB RF DISTRIBUTION AMPLIFIERKINGRAY
00760602 DW32
42DB RF DISTRIBUTION AMPLIFIERKINGRAY
00760643 DW42
SPLITTER AMPS
BRACKET FOR MOUNTING MD100US
00760011 KR001
2WAY SPLITTER AMPLIFIERHILLS
00760082 BA218
12DB 4WAY 'F' TYPE SPLITTERHILLS
00760145 HTA104
Remote Powered Wide band 4 way Splitter Amplifier Ideal for duplex or flats with no common power VHF Equaliser Control Multi-powering Balance VHF low band/ VHF high band and UHF signals for distribution Power Pass: Inline application to power through to a masthead amplifier
Weatherproof housing allows both indoor (screw to rafter or beam) or outdoor (strap to mast) mounting
Optimised for both digital and analogue tv signal application Frequency Range: 44 - 860 MHz
Maximum Gain: VHF 12 dB/ UHF 16 dB Output Level: 99 dB DIN45004B/ -60 dBIM Noise Figure Typical: <3.5 dB Return Loss: >10 dB Adjustable Gain Control: 14 dB @ 44 MHz/ 8 dB @ 860 MHz
16DB 4 WAY SPLITTER AMPLIFIERKINGRAY
00760580 SAM224
ACCESSORIES
Suitable for powering Masthead TV amplifiers via the coaxial cable
22V AC 150MA POWER SUPPLY
00760736 PS22
Suitable for powering amplifiers via the coaxial cable
'F' LINE POWER INJECTORKINGRAY
00760720 PIK01
2 WAY SPLITTER & POWER SUPPLYHILLS
00760202 PSU1
Low voltage supply to a remote amplifier via the coaxial cable
Also provides an outlet to second TV 3 x PAL sockets plus AC double adaptor
Low voltage supply suits Hills “A” series Mast Head Amplifiers.
Powered via 240VAC mains lead. 15.5VAC :90mA - 2 x PAL sockets
POWER SUPPLY HILLSHILLS
00760204 PSU2C
CATALOGUE 2010 - 2011142
TV ANTENNA & SYSTEMS
240V 50Hz 2.0A Mains supply 44-860MHz TV Signal Booster Gain: 18dB to two outlets Noise figure 6dB typical High Output: 8 channels 98 dBuv Australian Made and Approved PAL type sockets LED Power Indicator SMD design Electrical static protection Continually adjustable preset gain control from Min: Ch2 +4dB, Ch 10 + 8dB to Max: +10dB
Connects 75 ohm coaxial cable to 300 ohm terminals on the aerial with flexible wire leads
Coax cable entry through rubber grommet
44-860MHz TV Signal Boosters powered by PSK06 Mains adaptor via coaxial cable to power port on amp
Noise figure 6dB typical Output: 8 ch 98 dBuv 4 x Coaxial: "F" type outlets with 10dB Gain SMD design Electrical storm and static protection PAL type sockets Continually adjustable preset gain control from Min: Ch2 +4dB, Ch 10 + 8dB to Max 10dB
240V 50Hz 2.0A Mains supply 44-860MHz Gain: 14dB to four outlets Noise figure 6dB High Output: 8 channels 98 dBuv SMD design Electrical storm and static protection Continually adjustable preset gain control from Min: Ch2 +4dB, Ch 10 + 8dB to Max: +10dB
PAL type sockets Fully adjustable gain control
2WAY SPLITTER AMPLIFIERKINGRAY
00760682 SA162 2 Way - PAL type sockets00760683 SA162F 2 Way - 'F' type sockets
00760684 SA164 2 Way - PAL type sockets00760688 SA164F 2 Way - 'F' type sockets
4WAY SPLITTER AMPLIFIER
4WAY 'F' SPLITTER AMPLIFIERKINGRAY
00760686 SA164R
BALUNS & ATTENUATORS
ATTENUATOR
00761352 AT20
ATTENUATOR 'F'
00761355 ATT3F 3DB00761357 ATT6F 6DB00761359 ATT9F 9DB00761361 ATT12F 12DB
00761372 ATT3B 3DB00761374 ATT6B 6DB00761376 ATT12B 12DB00761380 ATT18B 18DB
00761385 ATT6FP 6DB00761390 ATT9FP 9DB
00762990 MHB2
UHF/VHF TV BALUN - OUTD0OR
Connects 75 ohm coaxial cable to 300 ohm terminals on the aerial with metal tabs
UV stabised plastic suitable for outdoor use
0~20dB / 0~900MHz Shielded box with screw holes for panel mounting Easy to use control knob PAL plug/socket connections
ATTENUATOR PAL
ATTENUATOR 'F' TYPE
MASTHEAD 'F' ANTENNA BALUN
00763002 EU235F
MASTHEAD 'F' ANTENNA BALUN
00763015 BT3F
PAL SOCKET ANTENNA BALUN
00763048 EU276A
SCREW BALUN 300 OHM TO 75 OHM
00763088 EU287
SPLITTERS & TAPS
Connects 75 Ohm coaxial cable through “F” Type connection to 300 Ohm terminals on aerial with insulated wire leads
Matching transformer with 75 ohm coaxial socket input and 300 ohm ribbon cable with spade terminal output 75 to 300 Ohm
Plugs directly into 75 ohm input socket of TV set, screw terminal
300 ohm ribbon input 300 ohm to 75 ohm PAL output
ACCESSORIES
2 WAY PAL SPLITTERPRO2
00845260 EU275P
Right angle 2-Way 75 ohm coaxial splitter
Commonly used in wall sockets for TV, Video or FM tuner output
00845128 EU222 2 Way00845136 EU223 3 Way00845144 EU224 4 Way
SPLITTERDOSS
2, 3 & 4 WAY 75 ohm coaxial splitter boxes Isolation: 25dB. 75 ohm coaxial cable input to 75 ohm cable outputs, saddle and screw terminating
V.S.W.R.: 1.3 Power Pass
RADIO PARTS GROUP 143
D
TV ANTENNA & SYSTEMS
High quality Zinc diecast housing “F” type. Directional taps designed to operate down to 5MHZ permitting use in inter-active systems
For both VHF and UHF frequencies Impedance 75 ohm Built in grounding block Power passing 24 VDC 1A (max) 1, 2 and 4 Way Types Tap value: 10dB ~ 25dB
2/4 Way 75 ohm coaxial splitters 900MHz Splitters with power pass on one leg Metal shielded case with F type sockets
00845434 FSP2F 2 Way00845435 FSP4F 4 Way00845436 FSP3F 3 Way00845437 FSP6F 6 Way00845438 FSP8F 8 Way
00845350 SP2F 2 Way00845354 SP3F 3 Way00845358 SP4F 4 Way00845360 SP6F 6 Way00845362 SP8F 8 Way
00845403 ST3115PP 1 Way 15dB00845406 ST3120PP 1 Way 10dB00845409 ST3210PP 2 Way 10dB00845415 ST3225PP 2 Way 25dB00845421 ST3415PP 4 Way 15dB00845424 ST3420PP 4 Way 20dB
'F' SPLITTERDOSS
High quality Satellite & Cable compatible 75 ohm splitters in Zinc diecast housing
F-type connections designed to operate from 5MHz to 2.4 GHz permitting use in inter-active systems
For both VHF and UHF frequencies Built in grounding block All ports power pass
SP8F
SP2F SP3F SP4F
SP6F
MHz (dB) SP2F SP3F SP4F SP6F SP8FLoss: 5-40 4.5 6.9 8 12 13.5Loss: 40-1000 4.5 7 8.5 13.6 13.6Loss: 1000-1750
5.5 8.5 9.8 14.7 16
Loss: 1750-2400
7.2 11 12.6 16.5 18
Isolation: 5-40 14 18 20 20 20Isolation:40-1000 20 21 22 22 20
Isolation: 1000-2400
20 22 21 21 22
Return Loss: 5-40
14 12 12 9 9
Return Loss: 40-1000
13 16 14 13 13
Return Loss: 1000-2050
15 14 13 13 13
Return Loss: 2050-2400
12 12 12 12 12
'F' TAP / SPLITTER
2 & 4 WAY 'F' SPLITTER FREE TO AIR
4 WAY RF SPLITTER WITH IR*RESI-LINX
00845450 RLRF300
2 WAY RF SPLITTER WITH IRRESI-LINX
00845455 RLRF310
3 IN 8 OUT COMBINER, AMPLIFIER*RESI-LINX
00845460 RLRF380
DIPLEXER & TRIPLEXERS
UHF/VHF DIPLEXERKINGRAY
00763335 DPOUV
Combines the UHF and VHF to one single signal Insertion Loss: typically <1dB VHF/UHF Rejection: UHF Input - 50dB VHF VHF Input - 35dB UHF AC Pass on VHF Input Unique SMD Design/Printed Coils
Passive splitter with 1 input, 4 outputs
Passive splitter with 1 input, 2 outputs
Passive splitter with 3 input, 8 outputs
Consists of three 'all-in-one' tight and pass filters to pass our standard television bands which have low insertion loss
Eliminates all unwanted signals that can interfere with both analogue and digital signals
Fully shielded die-cast housing that can be bracket mounted in front of a distribution amplifier, or left in its plastic housing to be installed outdoors in front of a masthead amplifier
Also doubles up as a diplexer or triplexer depending on how the switches are configured
A mast mounting UV resistant Diplexer combines the incoming signals from a UHF aerial & a VHF aerial.
The combined signal is fed by a single coaxial cable to the TV set
Power pass Input: UHF -75 ohm, VHF - 75 ohm
Output: UHF/ VHF - 75 ohm
Power Pass Options High Isolation Low Insertion Point
UHF/VHF DIPLEXERKINGRAY
00763338 DPOUVF
UHF/VHF DIPLEXERHILLS
00763344 DPUV
UHF/VHF TRIPLEXERKINGRAY
00763347 FL3BPMH
ACCESSORIES
SPLITTER / COMBINERCHANNEL PLUS
00842065 CP2514 IR Pass 4 Way00842100 CP2538 IR Pass 8 Way00842070 CP2532 Non Pass 2 Way00842080 CP2534 Non Pass 4 Way
Bi-directional 4-way splitter/combiners provide 1 GHz bandwidth ideal for antenna, coaxial cable operations.
The splitter/combiner is one product that can be used for two applications, it can be used to split the signal from a source, or combine signals on one run
Non Power & IR pass In section Loss: 2 Way: 4.0 dB, 4 Way: 9.0dB
*See Page. 399 for Model Diagram
*See Page. 399 for Model Diagram
CATALOGUE 2010 - 2011144
TV ANTENNA & SYSTEMS
SATELLITE ACCESS.
SATELLITE LNB FOR OPTUS AURORA
01002022 KFM21
KU BAND SATELLITE LNB STRONGSTRONG
01002024 SRTL721
KU BAND SATELLITE LNB STRONGSTRONG
01002026 SRTL801
Low phase noise, improved noise figure, excellent local oscillator stability, high isolation 13/18 V horizontal / vertical switch
Optus frequency range R48 Local Osc. Frequency: 10.7 GHz
Input Frequency Range: 11.7-12.75GHz Output Frequency Range: 1,000-2,150 MHz Noise Figure: 0.7 dB(Typ.) F/D Ratio: 0.6 Cross Polarity Isolation: 22 dB(Min.) 28 dB(Typical)
Low Noise Blocker supporting a wide range of satellites such as Optus B3, Optus CI, Optus Bi and many more.
Input: 12.25~12.75 GHz Output: 950~1450MHz L.O.: 11.30 GHz
Input: 11.7-12.75GHz Output: 1000-2050MHz
KU BAND SATELLITE LNB STRONGSTRONG
01002028 SRTL802
C-BAND SATELLITE LNB STRONGSTRONG
01002030 SRTL926
2 WAY SATELLITE DISEqC SWITCH
01003022 19CDS2
4 WAY SATELLITE DISEqC SWITCH
01003044 19CDS4
FTA SATELLITE DIPLEXER FITTING
01005000 07CDWC
2X Satellite 'F' Inputs 1X Satellite 'F' Output
4X Satellite 'F' Inputs 1X Satellite 'F' Output
Combines TV signal with satellite signal Suits Clipsal wall plates
Input: 11.7-12.75GHz Output: 1000-2050MHz
To receive satellite signals, you need a LNB (Low Noise Block). What this does is picks up all the signals being bounced off the dish and filters out selected frequencies and amplifies the frequencies you need. It then sends the required frequencies to the satellite decoder box.
TV HARDWARE
MASTING
1.5MT MAST EXTENSION POLE
00902400 ME15Z
GALVANISED MASTHILLS
00902408 GM18 1.8m00902424 GM24 2.4m00902440 GM30 3m
00902456 FC180 6m00902472 FC172 9m00902488 FC164 12m00902504 FC156 15m
1.8m - 25.5mm Ø 2.4m - 31.7mm Ø 3.0m - 38.1mm Ø
Total length: 1.5 Meters
Hot dip galvanised and galvabond steel
TELESCOPIC TELEMASTSHILLS
Tubular telescopic guyed masts in heights of 6, 9, 12 and 15 meters
Lightweight, tubular Galvabond steel construction
Full range of mountings and rigging hardware available
Suitable for ground or roof mounting
Efficient, drop-in locking pins simplifies extending mast
Kit includes guy ring plates, thimbles etc. for mounting the mast
Specifications: 6m Telescopic: 2 x 3m lengths 9m Telescopic: 3 x 3m lengths 12m Telescopic: 4 x 3m lengths 15m Telescopic: 5 x 3m lengths
MOUNTING
U BOLT
00901160 UB200901176 UB400901197 UB5
U Bolts with nuts and washers UB2 - Size: 2.0” L x 1/4” UB4 - Size: 21/2” L x 5/16” UB5 - Size: 51/2” L x 5/16”
ACCESSORIES | TV HARDWARE
GUY WIRE / LASHING CLAMP
00901344 GWC1
38MM X 10MM COACH SCREW
50MM X 10MM COACH SCREW
65MM X 10MM COACH SCREW
75MM X 10MM COACH SCREW
00901432 CS38
00901440 CS50
00901450 CS65
00901460 CS75
Plated clamp for securing guying or lashing wire
Mounting screw suitable for fixing brackets to timber facias
Suits Curved facia mount, Eave mount and Brackets
Depth: 36mm, suits 8mm hole
RADIO PARTS GROUP 145
D
TV ANTENNA & SYSTEMS
SCREWEYE
Length Hole00901512 SE4 150X9mm 8mm00901528 SE7 230x9mm 8mm
Used for guying antenna mast Wood screw type
MAST FOOT STRAMIT
00901755 MFS1
267MM GUYING BRACKET
00901760 GB9
GUY CLEAT GALVANISED
00901765 GCG1
GUYING PLATE
00901770 GP32 32mmØ00901776 GP38 38mmØ00901781 GP42 42mmØ00901792 GP51 51mmØ
TV Antenna Hardware Mast Foot Stramit
Guy anchor plate Hot dip galvanised Length: 267mm
TV Antenna Hardware Galvanised Zinc Plated guy cleat
Hot dip galvanized guy ring plates to suit mast sizes of:
32mm 38mm 42mm 51mm
00902516 FC602448
DRAW BAR MOUNT SUIT CARAVAN
00902520 DBRM
Mounts on caravan tow bracket (A frame) with hand tightening fixing bolts
Accommodates standard antenna masts 1mtr bracket, for mounting masts to brick or timber walls and facia panels.
20 GAUGE THIN GUYWIRE (180MT)
00901880 GW20
16 GAUGE THICK GUYWIRE (90MT)HILLS
00902208 GW16
LOCKING RING
00902510 LR3200902511 LR3600902512 LR4200902515 LR51
Plated locking rings with locking screw
LR32: suits Mast: 32mm Ø LR3: suits Mast: 36mm Ø LR42: suits Mast: 42mm Ø LR51: suits Mast: 49mm Ø
180MM 'D' TYPE MAST CLAMP
180mm Galvanized “D” Clamp Suits mast up to 52mm in diameter.
MAST EXTENSION KIT
00902552 MEK2Z
Contains: 2 long “U” bolts (152mm) and 6 x V blocks, with nuts and washers
Extends any standard mast
AS2841 Standard Zinc plated. Suitable for antenna mast guying data cabling
Guy wire: 7 strands. 16 gauge galvanised coil
SINGLE CHIMNEY MOUNT KITDOSS
00902712 CM6DZ
DOUBLE CHIMNEY MOUNT KITDOSS
00902728 CM12MZ
EAVE MOUNT KIT HILLSHILLS
00902744 EMK17
1MT EAVE MOUNT BRACKET HILLSHILLS
00902750 EMB1
Eave mount kit consists of: 280mm bracket, 1m bracket with “U” bolts, nuts and washers for mounting masts to brick or timber walls and facia panels
Model for strong fitting of small to medium antenna masts to chimneys
Double strap kit allows for adjustable length between mast attachment points for fitting long masts to chimneys
TV HARDWARE
CATALOGUE 2010 - 2011146
TV ANTENNA & SYSTEMS
280MM EAVE MOUNT BRACKET
00902752 EMB280Z
FLUSH WALL MOUNT
00902765 FWM1Z
IRON ROOF MOUNT
00902792 IRM6
LOFT MOUNT HILLS
00902808 LMH26
For mounting mast to vertical flat surface
Sits on the ridge capping Suits Stramit or Brown built roof ridge capping Guying is necessary to secure mast
For mounting aerial under a tiled or shingle roof, on rafters or joists. Can be secured above or below rafter
Height above rafter: 360mm
LEAD FLASHING KIT 13-40MM
00902812 LFK1
Heavy malleable 490 x 410mm plate replaces roof tileThe rubber boot can be cut to accept pipe diameter's from 13mm to 9 0mm
280mm bracket, for mounting masts to brick or timber walls and facia panels.
PIPE FLASHING RUBBER BOOT
00902814 PFRB
1.8MT RAFTER ANTENNA MOUNT
Lead Flashing with rubber boot
TV Antenna Hardware
00902816 RM18-32Z 1.8m x 32mm00902818 RM18-25Z 1.8mm x 25mm
Mast
For securing to a roof rafter The pole extends through the roof material Hot dip galvanised mast with angled plate for securing to rafters
Hole in base of mast accepts coach bolt
2X4' STAY BAR WITH COLLAR
00902820 SBK4Z
1200mm stay bars For supporting a mast or facia bracket Collar accepts masts from 25 ~ 32mm in diameter Note: Curved Facia Mount not Included
STEEL STRAMIT DECK MOUNT
00902824 SDM6Z
TELESCOPIC ANTENNA MAST FOOTHILLS
00902840 FB602498
Suits Stramit or Brown built clamp-down flat decking Can support standard masts without guying For masts up to 3 Metres.
For mounting telescopic masts, by bolting on to a solid base Suits masts up to 58mm in diameter
METAL FACIA MOUNTING BRACKET
00902846 MFMBZ
Attaches to pitch roof beam
TRIPOD ANTENNA ROOF MOUNT
00902850 TRM12Z
TILE ROOF ANTENNA MOUNT
00902872 TRM120Z
53CM VERTICAL ANTENNA MOUNT
00902882 VSB53
45CM HORIZONTAL ANTENNA MOUNT
00902886 HSB45
Hot dip galvanised adjustable roof mount complete with 1.2 metre mast
For mounting guyed masts on tile ridge
120° Tile Ridge
53 cm mount For mounting antenna vertically away from mast Takes up to 2" vertical masting
45 cm Horizontal mount Designed to mount the antenna horizontally away from the mast
Takes up to 2" vertical masting
VERTICAL ANTENNA MOUNT HILLSHILLS
00902888 VPB1
Vertically mounts the antenna away from the mast Designed to take vertical masting up to 2” in diameter
Constructed of heavy gauge galvanised metal Supplied with 5/16” U bolts Note: Masts Not Included
TV HARDWARE
RADIO PARTS GROUP 147
D
TV ANTENNA & SYSTEMS
1.5MT CURVED FACIA MOUNT
00902991 CFM5 1.5m
CAP SUIT CFM6
00902994 CFMCAP
Curved mast attached to mounting plate, for facia board mounting Secured by galvanised coach bolts or drilled bolted For masonry dyna bolts, loxins. etc.
Plastic Cap for 25mm diameter television mast Fits over end of the mast to seal out water Suits CFM6 Curved Facia Mount
1.8m X 25mm (1.6mm Wall) Zinc curved facia mount
1.8MT CURVED FACIA MOUNTDOSS
00902996 CFM6Z
CENTRE SUPPORT BRACKETHILLS
00903005 FB603836
CANTILEVER SUPPORT BRACKETHILLS
00903010 FB603844
3.6MT STEEL MAST STRAPPING KITHILLS
00903816 SK3053
Centre brace bracket for TCX34 UHF Antenna
Cantilever bracket for TCX20 UHF Antenna
Galvanized Strapping Kit Includes: 3.6metre Galvanised steel coil 2 x “J” bolts & seals
STRAP SEAL TERMINATION
00904200 3015
6MM THIMBLE FOR LASHING WIRE
00904216 TH2203
6MM 1/4" TURNBUCKLE
00904256 TB897
8MM 5/16" TURNBUCKLE
00904260 TB185
"V" BLOCK STANDARD
00904501 V1
ROTATOR
AUTOMATIC ANTENNA ROTATORMASTERROTOR
00903501 AR300XC
SATELLITE HARDWARE
SAT TRIPOD MOUNT WITH LEAVE
00905010 PSTMZ
DIGITEK FLEXI IRON ROOF MOUNT
00906010 14CFIRMECO
GUTTER MOUNT SINGLE ARM
00906020 14CGMGAL
UNIVERSAL TILE MOUNTDOSS
00906025 TPMBKE1.8
6mm Thimble Suits guy or lashing wire, galvanised, prevents fraying
Portable Tripod Mount Suitable 65cm-80cm dish
Folds Away for easy storage
Pre galvanised steel Top part is powder coated in black
44m mast tubing
Galvanised - non slip termination of mast strapping
6mm hook and eye Galvanised turnbuckle Overall Length: 185mm
8mm hook and eye, galvanised Overall length: 185mm.
Large V block For masts up to 58mm
TV Antenna Hardware Screw Foot Stramit
Ideal for reception in difficult areas, or where two or more channels are available in different locations.
Consists of remote control box and drive unit Vertical load: 45kg Stat breaking: 500Nm Rotation Torque/ speed: 20nM/ 70sec round
Satellite Mount for tin roof Pre-Galvanised steel Mast is 44mm diameter Stay bars are 22mm
Single arm Satellite gutter Mount for rafter 44mm
Pre-galvanised tube Comes with black cap
TV HARDWARE