PIS

TO

L

PAGE 214 Office/Tech: 641-623-5401GUARANTEED. FOREVER.

SINCE 1939

FRA

ME

S/SL

IDE

SPISTOL INDEX

Barrels . . . . . . . . . . . . . . . . . . . . . . . . .218-222 Magazines & Parts . . . . . . . . . . . . . 226-230

Frames/Slides . . . . . . . . . . . . . . . . . . . 214-218 Magwells . . . . . . . . . . . . . . . . . . . . . . . . . 224

Grips & Screws . . . . . . . . . . . . . . . . 239-240 Safeties . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 222

Guide Rods . . . . . . . . . . . . . . . . . . . 223-224 Springs . . . . . . . . . . . . . . . . . . . . . . . 230-232

Ignition Parts . . . . . . . . . . . . . . . . . . 237-239 Triggers & Components . . . . . . . . . 232-237

Mag & Slide Releases . . . . . . . . . . . 224-226

Drop-in conversion sys-tem replaces the top end of your Glock 20/21 pistol and converts it to fire the hard-hitting, yet controllable, 50 GI cartridge. Developed by Guncrafter, the 50 GI’s head is the same diameter as a .45 ACP, so the rest of your pistol remains stock, allowing easy conversion back to the original caliber. 50 GI ammo can be loaded to drive a 185 grain bullet at 1,200fps, with a felt recoil similar to 230 grain .45 ACP ball ammo. Delivers greater knock-down power, while remaining controllable during rapid fire. Conversion unit comes ful-ly assembled with 41/2" stainless steel barrel, firing pin, and guide rod with captive recoil spring. Slide and barrel are precision machined from stainless steel forgings to the same exacting tolerances as the original factory components. Non-reflective, matte finish is durable and good-looking. Black polymer fixed sights with easy to acquire white dot on front sight and U-shaped white outline around rear sight notch. The SF-style magazine uses a modified .45 ACP fol-lower and has an extended base pad that allows it to hold 9 rounds; convenient witness holes at the rear. Fits standard mag pouches for .45 caliber Glock mags. Cut for SF-style magazine catch. Additional magazines available separately. abSPECS: Slide/Barrel Assembly - Stainless steel, matte finish. Magazine – Stainless steel liner, black polymer shell, base pad, and follower. 9-round capacity. May require some fitting of conversion unit’s locking lug and/or pistol’s locking block. Fits Glock 20/21 pistols only.

GUNCRAFTER INDUSTRIES

50 GI® CONVERSION SYSTEM for GLOCK®

Steps Up Large-Frame Glock Pistol To Powerful

.50 Caliber Cartridge

#100-003-756AU 50 GI Conversion System for Glock, 9A763Q99 � � � � � � � � � � � � � � � � � � � � � � � � $ 810.99

#100-003-757AU 9-Rd Mag for 50 GI Conv., 9A61A99 � � 64.99

Complete slide assembly enables the firing of .22 LR car-tridges in your centerfire CZ 75. The Kadet is the same size as the centerfire slide, but only the lower third moves, reducing the

overall mass but still retaining the ability to cock the hammer. Slide stop will hold open and release the slide the same as on origi-nal pistol. Conversion kit is constructed of forged steel and comes with an adjustable rear sight, plus two 10-round .22 LR maga-zines. Minor fitting may be necessary for correct slide-to-frame fit on your specific pistol. Fits full-size CZ 75, plus these com-

pact/sub-compact models: 75 Compact, P-01, P-06, PCR, and RA-MI. Magazines will extend beyond the bottom of grip frame on these models. Kadet will not work on the 97, 75 TS, P-07, or P-09 models. SPECS: Steel, blued. 8.11" (20.6cm) OAL. 4.72" (12cm) barrel length. 1.1 lbs. (499g) wt.

CZ USA CZ 75

KADET II RIMFIRE CONVERSION UNIT

#100-015-794AU CZ 75 Kadet II Rimfire Unit, 7H448B99 � � � � � � � � � � � � � � � � � � � � � � � � �$ 461.99

Turns Your CZ Into A Training Or Plinking Pistol

Our front cut slides allow you to build a custom Glock® Gen3 style pistol from the ground up

with a slide already customized with front slide serrations. Our Front Cut Slides feature a unique wraparound slide serration design that aids in weapon manipulation, especially when checking the cham-ber. Serrations are cut to the same depth as Glock® factory models to ensure lower slide rigidity. Models are also available with top window cutout between the front serrations. Slides start out as 17-4 stain-less steel billet and are machined internally to factory specifications. Slides are compatible with any standard Glock® 17 or 19 compo-nents. The factory Glock® rear sight dovetail is machined, with a standard Glock® front sight cut at the front. Heat treated and finished with a matte Black Nitride finish. Factory internal dimensions - so excellent compatibility with factory and aftermarket components. Factory Glock® sight cuts. For Gen3 pistols. ab

SLIDES for GLOCK® 17/19 Foundation for a Superb D.I.Y.

Pistol - Ergo Enhancements for Better Control

#078-000-366AU Slide for Gen3 Glock® 17, 6H185J99 � � $ 199.99#078-000-368AU Window Slide for Gen3 Glock® 17,

6H195K99 � � � � � � � � � � � � � � � � � � � � � � � � 209.99#078-000-367AU Slide for Gen3 Glock® 19, 6H185N99 � � 199.99#078-000-369AU Window Slide for Gen3 Glock® 19,

6H195L99 � � � � � � � � � � � � � � � � � � � � � � � � 209.99

Our RMR Slides for Glock® pistols feature a distinctive, wrap-around serration pattern that aids in manipulating the slide, espe-

cially when checking the chamber. (OK, we’ll admit it: the serrations look cool, too.) They also come with a pre-cut slot for easy, secure, low-profile mounting of a Trijicon RMR sight. All Front Cut RMR Slides also have standard Glock factory front and rear sight dovetails for "iron" sights. Since the RMR sits low, it can easily co-witness with iron sights. In addition, you can get your Front Cut RMR Slide with an optional "window" cutout on top between the front serrations that reduces weight and enhances airflow to keep the barrel cooler - ideal for hard-working action competition pistols. Each Front Cut RMR Slide starts life as a billet of 17-4 stainless steel that is machined to Glock® factory specifications inside, so it’ll fit factory frames and accept factory or aftermarket barrels and parts. Fits Gen3 Glock 17 and 19 pistols & components. Heat treated to add surface hardness & given a wear-resistant matte black Nitride finish. Pre-cut Trijicon RMR mounting slot, plus factory front/rear sight cuts. This slide is the ideal upgrade for your factory Glock 17 or 19 pistol - and the perfect top half for a new custom gun built on an 80% frame. Available with distinctive top window cutout or traditional solid top. ab

RMR SLIDE FOR GLOCK® 17/19Stainless Steel Slide With a Bundle of Custom Features

#078-200-001AU RMR Slide for Gen3 Glock® 17, 8G206M99 � � � � � � � � � � � � � � � � � � � � � � � $ 229.99

#078-200-003AU Window RMR Slide for Gen3 Glock® 17, 8G216H99 � � � � � � � � � � � � � � � � � � � � 229.99

#078-200-002AU RMR Slide for Gen3 Glock® 19, 8G206H99 � � � � � � � � � � � � � � � � � � � � � � � 229.99

#078-200-004AU Window RMR Slide for Gen3 Glock® 19, 8G216B99 � � � � � � � � � � � � � � � � � � � � 229.99

Brownells Blank Slides for Glock® pistols come with the exterior left smooth and featureless so you can customize it exactly the way you want it. Add cocking serrations, an optic mounting slot, and cosmetic flourishes to make it entirely your own. (Yes, you will need to bring some machining skills to the table!) Inside, the dimensions fully machined to factory dimensions, so your Brownells Blank Slide for Glock comes ready to fit a factory-spec frame and accept Gen 3 factory and aftermarket barrels and parts. Models for Gen3 Glock® 17 and 19 pistols. Machined from firearm-grade 17-4 stainless steel. Comes "in-the-white" so you can apply the finish of your choice. Includes Glock factory front and rear sight dovetails. Sometimes "off the shelf" works, sometimes you want to do it your way. When you’re ready to build your own Glock®-platform Dream Gun™, reach for a Brownells Blank Slide. ab

SLIDE BLANKS for GLOCK® 17/19

A "Blank Canvas" for Your Next Custom Pistol

Masterpiece

#078-200-005AU Slide Blank for Gen3 Glock 17, 6H155E99 � � � � � � � � � � � � � � � � � � � � � � � � $ 174.99

#078-200-006AU Slide Blank for Gen3 Glock 19, 6H155I99 � � � � � � � � � � � � � � � � � � � � � � � � � 174.99

Brownells offers many inno-vations for the Glock® pistol, but one of our most novel offerings now gives Glock® fans the ability to mix and match components to create a custom hybrid pistol ideally suited to their personal

needs. The Brownells Extended Slide for Glock® 19 enables own-ers of the popular G19 pistol to put an extended G17-length slide on their guns. The result is a gun with a longer sight radius - for more accurate shooting - with the G19’s shorter frame, making it easier to carry concealed with less risk of "printing" through your clothing. Another enhancement on our Extended Slide for Glock® 19: wraparound, front-cut slide serrations that aid in manipulating the slide, especially for a quick check of the chamber. There are standard, factory-style serrations at the rear. You also get standard factory front and rear sight cuts on your Brownells extended slide so you can install any aftermarket sights that fit a Glock® factory slide.

• Fits Gen3 Glock® 19 frame ONLY

• Machined from hardened, corrosion-resistant 17-4 stainless steel billet

• Tough black Nitride finish with excellent wear resistance

• Accepts standard 9mm internal slide components

• Length: 7.21"

• 12 oz. wt.

Window models have a cutout up front on top that reduces weight and enhances air flow to keep your barrel cool during long practice sessions - plus it gives your pistol a unique, futuristic flair. RMR models also have a pre-cut slot for neat, secure, integrated installation of a Trijicon® RMR red dot sight (mounting screws for sight are even included). Blank slide is unfinished, ready for the skilled gunsmith (or metal worker) to cut slide serrations and other features exactly as needed by you - or your customer. But "cus-tom" work doesn’t mean unnecessary work - comes with factory sight cuts. Then it’s ready to accept a custom finish; go plain or go wild or something in between. Note: Due to changes in barrel-to-frame geometry caused by mating the longer slide with the smaller Glock 19 frame, a standard Glock 17 barrel won’t work with this slide. Instead, use the Brownells Extended Barrel for Glock® 19 (sold separately, #078-000-383, plain, or #078-000-384, with threaded muzzle). ab

19LS EXTENDED SLIDE for GLOCK® 19

Build Your Own Hybrid "Long Slide" Glock®

#078-000-411AU 19LS Slide for Gen3 Glock 19, 6H219G99 � � � � � � � � � � � � � � � � � � � � � � � � $ 249.99

#078-000-381AU Window 19LS Slide for Gen3 Glock 19, 6H239E99 � � � � � � � � � � � � � � � � � � � � 269.99

#078-000-412AU RMR 19LS Slide for Gen3 Glock 19, 6H242Q99 � � � � � � � � � � � � � � � � � � � � � � � 289.99

#078-000-382AU Window RMR 19LS Slide for Gen3 Glock 19, 8G253C99 � � � � � � � � � � � � � � 299.99

#078-000-380AU 19LS Extended Slide Blank for Gen3 Glock® 19, 6H206J99 � � � � � � � � � � � � � 219.99

Factory Sight Cuts + Window

RMR Cut, No Window

The JagerWerks cus-tom machines Glock® factory slides to provide a high-quality option for up-grading your Glock in one easy step: remove your pis-tol's factory slide and barrel assembly and replace it with the Breacher assembly. The Breacher slide has a window machined on both sides of the slide to give it that ultimate customized look as well as saving some weight. Front and top cocking serrations are added, providing possibly the most functional upgrade to any Glock® handgun. A slot for mounting a Trijicon RMR red dot sight is machined in front of the factory rear dovetail. Included is a carbon fiber cover plate to go over the slot when you don't have an RMR in-stalled on your pistol. JagerWerks retains the Glock® barrel, sights, extractor assembly, striker assembly, and striker safety plunger - why replace what already works very well? After the machining is done, JagerWerks finishes these slides in durable Black Nitride or Flat Dark Earth (FDE) Cerakote®. Or you can get a two-tone version that mixes both colors with a unique Battleworn look.

JAGERWERKS

BREACHER SLIDE for GLOCK® 17/19

A Custom Job for Your Glock® in One Easy Step

#100-024-403AU Breacher G17 Slide, Black, 8A00FDQ � � � � � � � � � � � � � � � � � � � � � � � $ 1052.99

#100-024-404AU Breacher G17 Slide, FDE, 8A00GPM � � � � � � � � � � � � � � � � � � � � � � � 1095.99

#100-024-405AU Breacher G17 Slide, Battleworn Black/FDE, 8A00DJJ � � � � � � � � � � � � � 1062.99

#100-024-400AU Breacher G19 Slide, Black, 8A00EMK � � � � � � � � � � � � � � � � � � � � � � � � 992.99

#100-024-401AU Breacher G19 Slide, FDE, 8A00MFG � � � � � � � � � � � � � � � � � � � � � � � 1050.99

#100-024-402AU Breacher G19 Slide, Battleworn Black/FDE, 8A00FFL � � � � � � � � � � � � � � 1094.99

PIST

OL

PAGE 215Orders: 800-741-0015order on the web

brownells.com

FRA

ME

S/SLIDE

S

The PS9C DLC slide is the perfect top half for a finished Polymer80 frame. Aggressive front and rear serrations coupled with clean, modern lines and a heavy front chamfer allow effective manipulation and holstering of a PS9C-equipped pistol while maintaining a unique but low-key aesthetic profile, right down to the subtle P80 logo engraved for-ward of the ejection port. Fabricated from domestically-sourced 17-4 PH stainless steel, the slide is heat treated to 42-43 HRC, then given a DLC (Diamond-Like Carbon - an extremely hard, amorphous nanocomposite coating) finish for the ultimate in durability, lubricity, and resistance to wear. The PS9C slide is compatible with Glock® 19 Gen3 9mm components, making it the perfect way to complete your Polymer80 PF9 pistol build or as an upgrade to your existing OEM pistol. Slide ONLY - no barrel or internal components. Available in Glock Black or Flat Dark Earth (FDE). ab

POLYMER80 PS9C SLIDE FOR GLOCK®

Aggressive Look Sets It Apart from Ordinary Glock Slides -

Perfect Top End for a Finished 80% Frame

#100-023-749AU PS9C Standard Glock 19 Slide, Black, 9D375Q00 � � � � � � � � � � � � � � � � � � � � � � � �$ 375.00

#100-023-750AU PS9C Standard Glock 19 Slide, FDE, 9D375A00 � � � � � � � � � � � � � � � � � � � � � � � � � 375.00

AlphaWolf factory-profile slides are the perfect complement to your

original G17 or G19 or for an aftermarket receiver, including the new "D.I.Y." 80% receivers. They are machined form high-grade 416 stainless steel, hardened to Rockwell Rc 32-36 and compatible with all Gen 1-3 17 or 19 frames. The standard AlphaWolf models have the Gen3 OEM nose profile and cocking serrations. The AlphaWolf Featureless model has no profiling, serrations or sight cuts, allowing you to apply your own customized finish to the exterior. Internal machining has been completed on the AlphaWolf Featureless Slide for your convenience. All models are shipped in-the-white. With an AlphaWolf slide, you can build your own custom dream gun or complete an 80% frame. ab

LONE WOLF

ALPHAWOLF SLIDES for GLOCK®Ready To Be Customized To Your Preference & Top Off That Dream

Gun or Finished 80% Frame

#100-023-060AU AlphaWolf Glock 17 Gen1-3 Slide, 2K00PPP � � � � � � � � � � � � � � � � � � � � � � � � � $ 209.99

#100-023-061AU AlphaWolf Glock 19 Gen1-3 Slide, 2K00BHN � � � � � � � � � � � � � � � � � � � � � � � � 209.99

#100-024-200AU AlphaWolf Featureless Glock 17 Gen3 Slide, 2K174H95 � � � � � � � � � � � � � 174.95

#100-024-201AU AlphaWolf Featureless Glock 19 Gen3 Slide, 2K174G95 � � � � � � � � � � � � � 174.95

KE's Glock® upgrade slides are machined from premium 17-4 stainless steel, heat treated to Rc 42-43, and finished in black Mel-onite. This results in a slide with exceptional wear-resistance prop-erties, ready to put many thousands of rounds downrange without wearing out of spec. They accept OEM internals, barrels, and guide rods, as well as aftermarket parts. All also have machined cutout to directly mount the popular Trijicon RMR red dot sights. Bravo has front and rear cocking serrations and more aggressive angle cuts on the sides of the slide, plus dovetails on the topside to accept traditional front/rear iron sights. Includes matte black anodized cover plate to conceal the RMR slot when your shooting wthout the red dot mounted. Charlie also has front/rear cocking serrations, plus aggressive contouring on the sides, bull nose on the front, and weight relief cuts on the top and sides. Delta has all the features of the Charlie, plus the slots cut through the front serrations further reduce weight and aid in barrel cooling. ab

KE ARMS

BRAVO, CHARLIE & DELTA SLIDES for GLOCK®

Make Your Pistol Unique - Three Configurations To Choose From,

All RMR-Ready

Bravo G17

#100-023-175AU Bravo G17 Gen 3 Slide, 6A379P99 � � $ 429.99#100-023-176AU Bravo G19 Gen 3 Slide, 6A379E99 � � 429.99#100-023-177AU Charlie G17 Gen 3 Slide, 6A479I99 � � 549.00#100-023-178AU Charlie G19 Gen 3 Slide, 6A479N99 � � 549.00#100-023-179AU Delta G17 Gen 3 Slide, 6A519N99 � � � 599.00#100-023-180AU Delta G19 Gen 3 Slide, 6A519D99 � � 599.00

Charlie G17

Delta G17

Polymer80 truly revolution-ized the world of custom pistols with their P80 80% frames. The P80 made it possible for the average shooter, with some basic me-chanical skills and tools, to build his or her own custom pistol from the frame up, and without the need bring an an FFL holder to handle the transfer of said frame. If you ARE an FFL holder, Polymer80 now offers these fully finished, serial-numbered frames for use as the foundation of custom pistols. They gives you the ergonomics and advanced features of the original 80% frames, only without the drill-ing and finishing steps. These frames are ideal for your next com-petition or duty pistol build. They come stripped and ready for as-sembly and customization with Glock®-compatible parts. Made of high-strength reinforced polymer, ready for multiple applications.

Two size options to choose from: Full-size PFS9 frame accepts Glock G17/22 slide and barrel. PFC9 Compact frame accepts Glock G19/23 slide and barrel. Available with ReadyMod® blank grip for custom texturing, Standard grip texture, or P80's Aggressive grip texture - your choice, whatever works best for the type of pistol you're building. The Polymer 80 Serialized Stripped PFS9/PFC9 frame for Glock® is a ready to serve as the solid foundation of your next build, with almost unlimited customization options! FFL required for purchase. ab

POLYMER80

COMPLETE SERIALIZED FRAMES for GLOCK®

Complete Frame for Building Custom Pistols - No D.I.Y. Work

Required

STOCK # COLOR PRICEPFS9 READYMOD SERIALIZED FRAME FOR G17/22

#100-030-162AU Black 9D114C00 $ 135.00#100-030-163AU FDE 9D114F00 $ 135.00#100-030-164AU ODG 9D114L00 $ 135.00#100-030-165AU TacGrey 9D114E00 $ 135.00#100-026-973AU Coyote 9D114H00 $ 135.00#100-030-167AU Robin’s Egg Blue 9D114N00 $ 135.00#100-030-166AU Cobalt 9D114J00 $ 135.00#100-026-971AU White 9D114L00 $ 135.00#100-030-168AU Black 9D114H00 $ 135.00#100-030-169AU FDE 9D114A00 $ 135.00#100-030-170AU ODG 9D114N00 $ 135.00#100-030-171AU TacGrey 9D114L00 $ 135.00#100-026-977AU Coyote 9D114F00 $ 135.00#100-030-173AU Robin’s Egg Blue 9D114M00 $ 135.00#100-030-172AU Cobalt 9D114K00 $ 135.00

PFS9 AGGRESSIVE TEXTURE SERIALIZED FRAME FOR G17/22#100-030-069AU Black 9D114C00 $ 135.00#100-030-070AU FDE 9D114M00 $ 135.00#100-030-071AU ODG 9D114B00 $ 135.00#100-030-072AU TacGrey 9D114G00 $ 135.00#100-030-073AU Coyote 9D114I00 $ 135.00#100-030-074AU Cobalt 9D114J00 $ 135.00#100-030-075AU White 9D114F00 $ 135.00

PFC9 STANDARD SERIALIZED FRAME FOR G19/23#100-030-050AU Black 9D114M00 $ 135.00#100-030-051AU FDE 9D114C00 $ 135.00#100-030-052AU ODG 9D114K00 $ 135.00#100-030-053AU TacGrey 9D114G00 $ 135.00#100-026-972AU Coyote 9D114L00 $ 135.00#100-026-970AU White 9D114I00 $ 135.00#100-030-055AU Robin’s Egg Blue 9D114E00 $ 135.00#100-030-054AU Cobalt 9D114N00 $ 135.00

PFC9 READYMOD SERIALIZED FRAME FOR G19/23#100-030-056AU Black 9D114J00 $ 135.00#100-030-057AU FDE 9D114G00 $ 135.00#100-030-058AU ODG 9D114G00 $ 135.00#100-030-059AU TacGrey 9D114G00 $ 135.00

STOCK # COLOR PRICE#100-030-060AU Cobalt 9D114P00 $ 135.00#100-026-976AU Coyote 9D114M00 $ 135.00#100-030-061AU Robin’s Egg Blue 9D114D00 $ 135.00

PFC9 AGGRESSIVE TEXTURE SERIALIZED FRAME FOR G19/23#100-030-062AU Black 9D114E00 $ 135.00#100-030-063AU FDE 9D114D00 $ 135.00#100-030-064AU ODG 9D114B00 $ 135.00#100-030-065AU TacGrey 9D114F00 $ 135.00#100-030-066AU Coyote 9D114N00 $ 135.00#100-030-067AU Cobalt 9D114B00 $ 135.00#100-030-068AU White 9D114K00 $ 135.00

Complete frame machined from alu-minum alloy weighs only 7 oz. and comes with a whole list of popular accurizing features to help you shoot super-precise groups with your Mark III. Each VC frame comes with all of the following items installed: extended bolt release, precision target trigger, wire-EDM cut target hammer and sear, Titanium dis-connector, spring-loaded magazine ejector, and an extended safety button. Each VC Frame ships from the factory with a clean, crisp 2¼ lb. trigger pull. The magazine disconnect has also been eliminated from this frame. Has the standard factory grip frame configuration, so it accepts any grips designed for Mark III steel frame. Available with or without a set of Volthane target grips. abSPECS: Machined aluminum, matte black finish. Accepts only Mark III mag-azines. Installation instructions included. FFL not required for purchase.

VOLQUARTSEN RUGER® MARK II/III/22-45

VC TARGET FRAMEPrecision-Machined Frame With

Match Grade Internal Parts Promotes Oustanding Accuracy

#930-000-131AU VC Target Frame, 3Z444A99 � � � � � � � $ 461.99#930-000-132AU VC Target Frame w/Target Grip,

3Z486G99 � � � � � � � � � � � � � � � � � � � � � � � � 639.99

PAC-LITE COMPENSATOR - 360-degree venting holes and a large internal expansion chamber dis-perse gasses evenly to help tame recoil and muz-zle rise, so that you can stay on target and make quicker follow-up shots. Sleek-looking compensator has same O.D. as Pac-Lite barrel; quickly screws onto ½"-28 tpi threads. SPECS: 6061-T6 aluminum, hardcoat anodized, matte black (MB) or silver (SIL). 2" (5.1cm) OAL. .900" (2.3cm) O.D. ½"-28 tpi threads. #100-011-117AU Pac-Lite Comp., MB, 8K31C07 � � � � � � � �$ 35.00#100-801-008AU Pac-Lite Comp., SIL, 8K31G07 � � � � � � � � 35.00

PAC-LITE STANDARD SCOPE BASE - Machined aluminum base attaches to a pre-drilled and tapped Pac-Lite barrel to allow the mounting of optics or other accessories. Compatible with Picatinny or Weaver-style scope rings. SPECS: 6061-T6 aluminum, hardcoat anodized, matte black. 3.4" (8.6cm) OAL. Fits Pac-Lite barrel/receiver.#100-011-118AU Pac-Lite Stdd Scope Base, 8K27F34 � � $ 28.00

TACTICAL SOLUTIONS RUGER® MARK I/II/III & 22/45

PAC-LITE BARREL/RECEIVER Provides Competition-

Ready Accuracy & Improved Balance For Better Handling

ab

ab

Lightweight, easy to install, replacement barrel/receiver turns

your Ruger Mark III or 22/45 pistol into a well-balanced, compe-tition-ready firearm in seconds. A button-rifled steel liner works with the integrated, adjustable rear sight and ramped front sight to deliver impressive accuracy. Durable, milled stainless steel ejec-tor is built for reliability and long-lasting performance. ½"-28 tpi muzzle threads enable attachment of the Pac-Lite compensator (sold below) and are pre-drilled and tapped for the Pac-Lite scope base (also sold separately). Fluted model provides further weight reduction. abSPECS: 6061 T6 aluminum, hardcoat anodized, matte black. 4140 steel-lined barrel. 4.5" barrel length. .900" (2.3cm) O.D. 1-16" twist. Fits Ruger Mark III and 22/45; also fits older model Mark I/II. 22/45 installation may require minor fitting. FFL required for purchase.

#100-011-119AU 4.5" Pac-Lite Barrel/Receiver, 8F287G57 � � � � � � � � � � � � � � � � � � � � � � � � $ 290.00

#100-011-120AU 4.5" Pac-Lite Fluted Barrel/Receiver, 8F293Q97 � � � � � � � � � � � � � � � � � � � � � � � � 300.00

Shoot More, Pay Less With .22 LR Ammo For

Practice

TACTICAL SOLUTIONS

TSG-222 CONVERSION KIT for GLOCK®

The TSG-222 .22 LR conversion system is built to the same high qual-ity standards as your original Glock pistol to provide a lower-cost alternative to burning up expensive cen-terfire ammo during practice. TSG-222 It has the same external dimensions as the factory slide and barrel, so the gun feels and moves the same – just with less recoil. Easy-to-install: remove the factory slide, replace with

the TSG-22 slide/barrel assembly, and insert the included 10-round rimfire magazine. Includes Glock sights with factory front white dot and rear white outline U-notch. Polymer magazine locks slide open after last round fired. Precision machined steel slide is treated with a friction-reducing black nitride finish for superb wear and corrosion resistance. Comes with one 10-round magazine. Spare magazines sold separately, below. Note: Does not fit Gen5 pistols. abSPECS: Slide – 4140 carbon steel, black nitride finish. Barrel - 4130 carbon steel, matte blued. Magazine – Polymer, black. 10-rd capacity. For best results, use .22 LR ammunition with 40 grain round nose bullets. TSG-222 17/22 fits all generations of Glock® 17, 22, 34, 35, and 37, including Gen4 models. TSG-222 19/23 fits all generations of Glock® 19, 23, 32, and 38, including Gen4.

#100-013-940AU TSG-222 17/22 Conversion, 10-Rd Mag, 8K344A99 � � � � � � � � � � � � � � � � � � � $ 344.99

#100-013-941AU TSG-222 19/23 Conversion, 10-Rd Mag, 8K00JGJ � � � � � � � � � � � � � � � � � � � � 329.00

#100-009-463AU 10-Rd TSG-22 Magazine, 8K22F37 � � � � � � � � � � � � � � � � � � � � � � � � � � 28.00

PIS

TO

L

PAGE 216 Office/Tech: 641-623-5401GUARANTEED. FOREVER.

SINCE 1939

FRA

ME

S/SL

IDE

S

Weighing just under 16 oz., this complete barreled receiver is precision machined from a single piece of aluminum alloy. An integral Picatinny rail is machined into the top of the receiver for optic and accessory mounting options. Upper receiver features a contoured, stainless steel barrel that has been machine-honed and lapped. Stainless steel breech face will withstand years of use. Receiver comes with 1/2 x28 muzzle threads and screw on thread protector. abSPECS: Aluminum, Type III hardcoat anodized finish, matte black. Fits Ruger Mark II, Mark III and 22/45. 6" - 15 oz. (425g) wt. 4.5" - 14 oz. (396g) wt. FFL required for purchase.

VOLQUARTSEN RUGER® MARK II/III & 22/45

LLV COMPETITION PISTOL UPPERLightweight, Machined

Billet Receiver With Stainless Steel Barrel

#930-000-140AU 6" LLV Competition Upper Receiver, 3F356P99 � � � � � � � � � � � � � � � � � � � � � � � � $ 410.99

#930-000-141AU 4" LLV Competition Upper Receiver, 3F332I99 � � � � � � � � � � � � � � � � � � � � � � � � � 438.99

Machined steel bolt drops into Ruger .22 pistol and helps eliminate stovepipes, failures to fire, and improves overall function. Offers superior tolerances, fit and finish. Bolt features the tool steel Exact Edge Extractor built to withstand years of use and the Sur-eStrike firing pin that helps eliminate light hits. Integral Extended Bolt Racker makes it easy to charge the pistol and avoid pinched fingers. abSPECS: Machined steel. Matte black finish except for stainless portion visible through ejection port. Includes recoil spring assembly.

VOLQUARTSEN RUGER® MARK II/III

COMPETITION BOLT ASSEMBLYEnhances Reliability & Performance For

Competition

#930-000-134AU Ruger Mark II Competition Bolt, 3Z253J99 � � � � � � � � � � � � � � � � � � � � � � � � $ 262.99

#930-000-133AU Ruger Mark III Competition Bolt, 3Z230B99 � � � � � � � � � � � � � � � � � � � � � � � � 238.99

Volquartsen developed the LLV Competition Upper to turn

the already excellent Ruger® Mark IV™ pistol into an outstanding .22 target pistol. To keep weight to a minimum and maintain perfect receiver-barrel alignment, the receiver and barrel shroud are preci-sion machined from a single piece of aluminum alloy, with a rugged Type III hardcoat anodized matte black finish. The Volquartsen Ru-ger® Mark IV™ LLV Competition Upper is fitted with a match-grade, stainless steel barrel that has a honed and lapped bore for superb accuracy potential and easy cleaning. The contours and weight dis-tribution are optimized for impeccable balance in the hand. A stain-less steel breech face withstands many thousands of firing cycles. Threaded muzzle is standard, thread protector included. The LLV fits on a standard Ruger® Mark IV™ grip frame ("lower" receiver). It comes with a Picatinny rail machined into the top of the barrel for installation of an optical sight. Available with a 4.5" or 6" barrel. Both are also available with adjustable "iron" Target Sights installed that can be used alone or co-witnessed with a non-magnifying red dot sight. FFL required for purchase. ab

VOLQUARTSEN RUGER® MARK IV™

LLV COMPETITION UPPEROptic-Ready Top-Half

Turns Your Ruger .22 Into a Competition Target Pistol

#930-000-155AU LLV Competition Upper, 4.5", 3Z00QGB � � � � � � � � � � � � � � � � � � � � � � � � �$ 337.50

#930-000-157AU LLV Competition Upper, 4.5" w/Sights, 3Z504G00 � � � � � � � � � � � � � � � � � � 504.00

#930-000-156AU LLV Competition Upper, 6", 3Z337G50 � � � � � � � � � � � � � � � � � � � � � � � � � 337.50

#930-000-158AU LLV Competition Upper, 6" w/Sights, 3Z00BEQ � � � � � � � � � � � � � � � � � � � � � � � � � � 504.00

Maybe ol’ King Leonidas didn’t have a Glock®, but if he had, you can bet he would appreciate the radical look the Spartan slide would have given it. Machined from a single billet of 17-4 stainless steel to tighter than the factory toler-ances, the Spartan delivers increased consistency in barrel lockup for improved accuracy. Window cutouts along the top edge not only let the barrel cool faster, they also make the slide lighter, resulting in a reduced reciprocating weight which translates into less recoil for faster follow up shots. Plus, they give the slide a highly customized look that is just plain cool! Angled front and rear serrations offer plenty of grip without getting hung up on your holster while the small top serrations help to reduce glare. A CNC machined cutout at the rear of the slide readily accepts any model RMR sight, and the beefy positioning posts hold the sight at a center zero point on the slide. Slide comes with proper mounting screws for the RMR of any model plus cover plate for those times you want to run the pistol without the optic. Available for both Gen3 G17 ("Z17" model) and G19 ("Z19" model) with a super-tough, scuff/wear/abrasion-resistant DLC (Diamond-Like Carbon) finish in traditional black or subdued gray. ab

ZEV TECHNOLOGIES

SPARTAN SLIDE for GLOCK®

17/19Upgraded Performance

With Plenty of Eye-Catching Aesthetic Appeal

#100-024-911AU Spartan Z17 Gen3 Slide, Black, 8B454J54 � � � � � � � � � � � � � � � � � � � � � � � � $ 499.99

#100-024-912AU Spartan Z17 Gen3 Slide, Gray, 8B454Q54 � � � � � � � � � � � � � � � � � � � � � � � � 499.99

#100-024-917AU Spartan Z19 Gen3 Slide, Black, 8B454E54 � � � � � � � � � � � � � � � � � � � � � � � � 499.99

#100-024-918AU Spartan Z19 Gen3 Slide, Gray, 8B454M54 � � � � � � � � � � � � � � � � � � � � � � � � 499.99

The complement to Lone Wolf's Spectre receiver completion kits, this kit contains all the neces-sary parts to complete the inside of a stripped Glock® slide, minus the barrel. This is a must-have item for any custom build involving an aftermarket slide, including an all-new custom pistol built on one of the popular 80% frames. Includes chan-nel liner, spacer sleeve, marine spring cups, mid-weight striker spring, striker, LCI extractor, spring-loaded bearing, depressor plunger and spring , firing pin safety and spring, and slide cover plate. Kit does not include recoil spring, barrel or sights. ab

LONE WOLF

SLIDE COMPLETION KIT for GLOCK®All the "Guts" To Complete a Stripped Slide (Except Barrel)

STOCK # CALIBER FITS PRICE#100-803-023AU 9mm 17, 19, 26, 34 & 17L 2K84D95 $ 84.95#100-803-021AU .40 S&W 22, 23, 27 35 & 24 2K84K95 $ 84.95

The PF940Cv1 and PF940v2 are Polymer80's next generation of 80% frames for Glock® pistols that enables you to create a customized handgun

yourself, from the bottom up. The PF940Cv1 comes with a finishing jig, an end mill, and all the necessary drill bits you need to complete the remain-ing 20% of the work to get a finished, working pistol frame. The PF940Cv1

offers high-strength reinforced polymer construction and improved ergonomics over the original Polymer80 frame that make it a superb platform for a reliable and great-shooting pistol. It is compatible with factory and aftermarket Glock® Gen3 internal components (not compatible with Gen4 parts). Inside, there's a stainless steel locking block to keep the fire control parts in place, and a stainless steel rear rail module that keeps the slide on track through many thousands of firing cycles. Hardened front and rear rail pins ensure the slide/rail/frame interface is - and stays - rock solid. A modified grip profile and improved overall balance make this not only an easier frame to operate and control, but also a unique looking one. Up front, there's an under-receiver Picatinny/STANAG rail for mounting any standard light or laser. The PF940v2 is the "full-size" frame that accepts Glock 17/22/31 Gen3 slides and and components, while the PF940Cv1 is the "compact" frame that accepts Glock 19/23/32 Gen3 slides and components. Both are available in three configurations: Standard with textured grips that aid in recoil control and retention of the pis-tol under stress. ReadyMod with completely smooth grips, ready for custom stippling to get the exact texture you prefer. The PF940v2-BE/PF940Cv1-BE models are available ONLY at Brownells ("BE" = Brownells Exclusive!) and come with what we're calling "aggressive" texturing on the grips that will give you an exceptionally firm hold to counteract recoil and muzzle rise under any conditions - even when your hands are wet or you're under extreme stress. Colors: Black, Flat Dark Earth (FDE), Olive Drab Green (ODG), Coyote, Tac-Grey, Robin's Egg Blue, White, and Cobalt. Not all models available in all colors. A note on Cobalt - although this color is usually a deep, vibrant blue, the color of these frames appears to be more of a dark gray or graphite color. ab

POLYMER80

POLYMER 80% FRAMES for GLOCK®

Ergonomic Upgrades, Plus Plenty of Customization Options for

Building Your Glock

STOCK # COLOR PRICE#100-023-590AU ODG 9D128J99 $ 154.99#100-023-591AU TacGrey 9D130P99 $ 157.99 100-024-324AU Coyote 9D126M99 $ 151.99 100-025-959AU Robin's Egg Blue 9D114Q99 $ 142.99 100-025-963AU White 9D114I99 $ 142.99 100-025-964AU Cobalt 9D114Q99 $ 142.99PF940CV1-READYMOD 80% FRAME for GLOCK 19/23/32

#100-023-489AU Black 9D125H00 $ 149.99 100-025-571AU FDE 9D125J00 $ 149.99 100-025-572AU ODG 9D125L00 $ 149.99 100-025-573AU TacGrey 9D125J00 $ 149.99 100-024-325AU Coyote 9D125G03 $ 149.99PF940CV1-BE AGGRESSIVELY TEXTURED 80% FRAME for

GLOCK 19/23/32#100-023-538AU Black 9D125E68 $ 149.99#100-023-539AU FDE 9D125L68 $ 149.99#100-023-540AU ODG 9D120K99 $ 147.99#100-023-541AU TacGrey 9D125D68 $ 149.99#100-023-542AU Coyote 9D125Q68 $ 149.99 100-026-651AU Cobalt 9D125A68 $ 149.99

STOCK # COLOR PRICEPF940V2 80% FRAME for GLOCK® 17/22

100-025-396AU Black 9D125P68 $ 149.99 100-025-398AU FDE 9D125K68 $ 149.99 100-025-399AU ODG 9D125E68 $ 149.99 100-025-400AU TacGrey 9D125F68 $ 149.99 100-025-397AU Coyote 9D125L68 $ 149.99 100-026-347AU Robin’s Egg Blue 9D139M99 $ 149.99 100-026-348AU Cobalt 9D139F99 $ 149.99

PF940V2-READYMOD 80% FRAME for GLOCK® 17/22 100-025-401AU Black 9D125J68 $ 149.99 100-025-403AU FDE 9D125A68 $ 149.99 100-025-404AU ODG 9D125P68 $ 149.99 100-025-405AU TacGrey 9D125D68 $ 149.99 100-025-402AU Coyote 9D125D68 $ 149.99

PF940V2-BE AGGRESSIVELY TEXTURE 80% FRAME for GLOCK® 17/22

100-025-335AU Black 9D121J00 $ 149.99 100-025-336AU FDE 9D121I00 $ 149.99 100-025-337AU ODG 9D121M00 $ 149.99 100-025-338AU TacGrey 9D121K00 $ 149.99 100-025-339AU Coyote 9D121C00 $ 149.99

PF940CV1 80% FRAME for GLOCK 19/23/32#100-023-488AU Black 9D125P03 $ 149.99#100-023-589AU FDE 9D128P99 $ 154.99

Race-Ready

Items

This upgraded slide is built to tighter tolerances than the facto-

ry slide for better potential accuracy from your pistol, plus expanded sight mounting options. This competition grade slide comes with the firing pin liner installed and a lowered ejection port to aid in the ejection of brass. And it adds a mounting slot for a Trijicon RMR red dot sight, positioning the RMR at the center zero point on the slide (mounting screws for the RMR included). The top still has dovetail cuts for traditional "iron" sights that can be co-witnessed with the RMR, if you like. Also included is an aluminum cover for filling the RMR slot should you choose to operate with "iron" sights alone. Models available for both Gen3 and Gen4 G17 (Z17 model), G19 (Z19 model), and G34 (Z34) with a super-tough, scuff/wear/abrasion-resistant DLC finish in traditional black, gray, or an eye-catching Bronze. Regardless of the slide color, the RMR slot cover is always black. Note: These are just the stripped slide alone, with channel liner installed, and the cover for the RMR slot. We also offer Drag-onfly Slide Kits that include sights and the other internal parts (minus the barrel), see separate listing. ab

Just the Slide With Built-In RMR Mounting Slot - Add the Exact Barrel & Other Components YOU Want

100-024-905AU Dragonfly Z17 Gen3 Slide, Black, 8B454B54 � � � � � � � � � � � � � � � � � � � � � � � � �$ 499.99

100-024-906AU Dragonfly Z17 Gen3 Slide, Gray, 8B454D54 � � � � � � � � � � � � � � � � � � � � � � � � � 499.99

#100-022-940AU Dragonfly Z17 Gen4 RMR Slide, Black, 8B459C59 � � � � � � � � � � � � � � � � � � 499.99

#100-022-934AU Dragonfly Z19 Gen3 RMR Slide, Black, 8B459A59 � � � � � � � � � � � � � � � � � � � 499.99

100-024-914AU Dragonfly Z19 Gen3 Slide, Gray, 8B454D54 � � � � � � � � � � � � � � � � � � � � � � � � � 499.99

#100-022-935AU Dragonfly Z19 Gen3 RMR Slide, Bronze, 8B459Q59 � � � � � � � � � � � � � � � � � 499.99

#100-022-938AU Dragonfly Z19 Gen4 RMR Slide, Black, 8B459A59 � � � � � � � � � � � � � � � � � � � 499.99

#100-022-939AU Dragonfly Z19 Gen4 RMR Slide, Bronze, 8B459I59 � � � � � � � � � � � � � � � � � � 499.99

100-024-919AU Dragonfly Z34 Gen3 Slide, Black, 8B474E74 � � � � � � � � � � � � � � � � � � � � � � � � � 523.00

100-024-920AU Dragonfly Z34 Gen3 Slide, Gray, 8B474F74 � � � � � � � � � � � � � � � � � � � � � � � � � 523.00

100-026-527AU Dragonfly Z34 Gen4 Slide, Blk, 8B479D00 � � � � � � � � � � � � � � � � � � � � � � � � � 523.00

ZEV TECHNOLOGIES

DRAGONFLY RMR STRIPPED SLIDE FOR GLOCK®

Items

PIST

OL

PAGE 217Orders: 800-741-0015order on the web

brownells.com

FRA

ME

S/SLIDE

S

VooDoo In-novations Glock slide assemblies are designed for an improved drop-in fit to factory or factory-spec aftermarket Glock frames. The VDI Slide is profiled lightened to reduce reciprocal mass and decrease felt recoil. These slides are cut from stainless steel with enhanced front and rear cocking serrations for improved manipulation and improved slide geometry to draw your eye to the front sight. The VDI Barrel is machined to tighter fitment tolerances to increase ac-curacy potential without the need of gunsmith fitting. The barrel features a SAAMI spec 9mm match chambering, Match Grade Rifling to allow the use of any 9mm projectile (not just jacketed bullets), threaded ½ x 28 TPI for use with 9mm suppressors and compensa-tors, machined from 416R stainless steel, and Finished in Voodoo Innovations LifeCoat process. Includes VDI Thread Protector. These Enforcer model features the RMR cut with cover plate and upgraded XS Sights Suppressor Dot Sights. ab

VOODOO INNOVATIONS

BRAWLER & ENFORCER SLIDES for GLOCK®

Complete Top Half With Barrel & Innards

- Plus, Innovative Upgrades

Brawler G17

#100-023-258AU Brawler Glock 17 Gen3 Slide Assembly, 4Z579G99 � � � � � � � � � � � � � � $ 629.99

#100-023-259AU Brawler Glock 19 Gen3 Slide Assembly, 4Z579L99 � � � � � � � � � � � � � � 629.99

#100-023-256AU Enforcer Glock 17 Gen3 Slide Assembly, 4Z679H99 � � � � � � � � � � � � � � 729.99

#100-023-257AU Enforcer Glock 19 Gen3 Slide Assembly, 4Z679B99 � � � � � � � � � � � � � � 729.99

Enforcer G17

ZEV's Dragonfly slides are designed to tighter tolerances than factory slides to promote better accuracy. An excellent upgrade for a factory pistol, or to top off a custom build. Slide is machined from a billet of 1704 stainless steel before receiving a tough DLC (Diamond-Like Carbon) finish. Custom serrations and cooling vents next to the barrel give a truly unique look, while providing a lighter, yet rugged slide. The top has dovetails for standard Glock® front and rear sights (sights included) AND a cutout for mounting a Trijicon RMR red dot sight. Positions the RMR low in the slide for a very secure installa-tion that can be co-witnessed with the "iron" sights. Kit contents: slide, RMR gasket and mounting screws, firing pin assembly, firing pin safety block and spring, extractor, extractor depressor plunger and spring, spring-loaded bearing, cover plate, and sight set. Barrel NOT included. ab

ZEV TECHNOLOGIES

DRAGONFLY SLIDE KIT for GLOCK®

Optimized To Promote Improved Accuracy - Heckuva Unique

Appearance

#100-019-702AU Dragonfly G17 Gen3 Slide Kit, 8B734B40 � � � � � � � � � � � � � � � � � � � � � � � � $ 798.00

#100-019-706AU Dragonfly G17 Gen4 Slide Kit, 8B690I41 � � � � � � � � � � � � � � � � � � � � � � � � � 798.00

#100-019-704AU Dragonfly G19 Gen3 Slide Kit, 8B734K40 � � � � � � � � � � � � � � � � � � � � � � � � 798.00

#100-019-708AU Dragonfly G19 Gen4 Slide Kit, 8B734M40 � � � � � � � � � � � � � � � � � � � � � � � � 798.00

Stainless steel pins fit into Glock pistols to give long service life and high resistance to corrosion and wear. Pins also add striking contrast color against the frame for enhanced appearance. JBP-1 kit fits into Gen 1, 2, and 3 Glocks and includes trigger pin, locking block pin and trigger housing pin. JBP-2 fits Gen 4 Glocks, and includes trigger pin, locking block

pin, short trigger housing pin for use without a backstrap, and long trigger housing pin for use with a backstrap. ab

JENTRA

STAINLESS STEEL PIN KIT for GLOCK®Pins Give Long Service Life &

Enhance Appearance

#463-000-010AU JBP-1 Stainless Steel Pin Kit, 3F17I99 � � $ 19.99#463-000-011AU JBP-2 Stainless Steel Pin Kit, 3F20A99 � � 23.99

Factory replacement back-strap kit for Glock Gen4 pistols comes with standard 2mm and 4mm backstraps. Kit also includes trigger housing pin and an instal-lation tool with a built-in polymer punch to assist in changing backstraps. These parts are factory re-placements, made to the same specifications as the originals in-cluded with your pistol. SPECS: Molded, black polymer. Fits Gen4 G17/22/31/34/35/37. Includes 2mm backstrap, 4mm backstrap, trigger housing pin, removal tool, in-struction sheet.

GEN 4 BACKSTRAP REPLACEMENT KIT for GLOCK®

#100-015-078AU Backstrap Kit for Gen4 G17/22, 1D18Q99 � � � � � � � � � � � � � � � � � � � � � � � � � � $ 20.99

#100-015-081AU Backstrap Kit for Gen4 G26/27, 1D18J99 � � � � � � � � � � � � � � � � � � � � � � � � � � � 29.99

Perfect For Increasing Grip Size

Polymer insert fits into gap at bot-tom of Glock grip to help keep out dirt and gives a beveled edge to help ease magazine removal and insertion. Inlcudes two plugs - one for use with back strap, one for use without back strap. Simply choose appropriate plug and insert it into the gap. abSPECS: Polymer, matte black. Fits Gen4 models 19, 17, 22, 23, 31, 32, 34, 35, 37 & 38. Fits only Gen4 pistols. Will not fit SF models.

GHOST

GRIP PLUG KIT for GEN4 GLOCK®Helps Keep Out Dirt & Enhances Magazine Insertion & Removal

#100-013-385AU Gen4 Grip Plug Kit, 7K7P93 � � � � � � � � � � �$ 8.95

Easy to install adapter helps improve grip and shooting control. Modifies the backstrap angle to create a subtle change in grip and wrist positioning that helps enhance pointability for improved sight

acquisition and faster follow up shots. Extended tang increases le-verage for better control during rapid fire and helps the user form the proper shooting grip, especially when drawing from a holster. Also prevents the slide from making contact with the skin between thumb and forefinger. Comes with a Gen 123SC adapter that fea-tures a smooth tang and a shorter backstrap. Easy to install with the included trigger housing pin. No permanent modifications to the gun; won’t damage the pistol or mar the frame. abSPECS: Textured plastic, black. Gen 123SC adapter fits Gen 4 pistols in the short frame configuration or with the Medium grip panel installed. Gen 123 adapter fits Glock Gen 1, 2, 3 pistols and the Gen 4 pistol with the Medium grip panel installed. May not fit pistols with letter L serial number prefix (i.e., LXX123). Increases trigger reach by .077" (1.96mm) and tang area thickness by .084" (2.13mm). Gen 4 adapter fits Glock Gen 4 pistols in the “SF” (short frame) configuration to give the pistol a more upright backstrap/grip angles, will not fit over the Medium or Large grip panels. Increases trigger reach by .091" (2.31mm) and tang area thickness by .085" (2.16mm).

Helps Improve Hold & Sight Acquisition For Fast Follow Up Shots

#100-011-617AU Gen 123 Grip Adptr for Glock, 9C21B88 � �$ 24.95#100-011-618AU Gen 4 Grip Adptr for Glock, 9C21J88 � � 24.95

GRIP FORCE GRIP ADAPTER for GLOCK®

Snaps into the opening at the rear of the Glock grip frame for a cleaner appearance, plus keeps dust, dirt, snow and water out of the gun. Creates a perfect location for adding extra weight to competition guns or to counter recoil on light, carry guns. Easily removed, does not alter gun. abSPECS: Synthetic polymer, black. JP-1 fits models 17, 19, 20, 21, 22, 23, 24, 25, 31, 32, 34, 35. JP-2 fits compact models 26, 27 and 33. Does not fit G29 or G30. JP-3 fits G30 only. JP-4 fits G21SF. JP-6 fits Gen4 17, 19, 20, 21, 22, 23, 24, 25, 31, 32, 34, 35 without backstrap insert. JP-7 fits Gen4 models 20, 21 and 41 without backstrap insert. JP-8 fits Gen4 models 26, 27, 33 without backstrap insert. JP-9 fits Gen4 models 17, 18, 19, 22, 23, 24, 25, 31, 32, 34, 35 with interchangeable backstrap inserts.

JENTRA GRIP PLUGS for GLOCK®Keeps Dirt Out Of

Grip Frame

#463-100-017AU JP-1 Grip Plug for Glock, 3F7E99 � � � � � $ 9.99#463-000-001AU JP-2 Grip Plug for Mini Glock, 3F5C99 � � 6.99#463-000-002AU JP-3 Grip Plug for G30, 3F7I99 � � � � � � � 8.99#463-000-004AU JP-4 Grip Plug for G21SF, 3F5B99 � � � � 6.99#463-000-012AU JP-6 Grip Plug for Gen4 Glock w/o

Backstrap, 3F5L99 � � � � � � � � � � � � � � � � � � 7.99#463-000-013AU JP-7 Grip Plug for Gen4 G20/21/41

w/o Backstrap, 3F5J99 � � � � � � � � � � � � � � 6.99#463-000-014AU JP-8 Grip Plug for Gen4 G26/27/33

w/o Backstrap, 3F5B99 � � � � � � � � � � � � � � 6.99#463-000-015AU JP-9 Grip Plug for Gen4 w/Backstrap,

3F7J99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 9.99#100-023-024AU Grip Plug for G42/43, 3F4A99 � � � � � � � � 6.99

Plastic plug installs in the bottom rear cavity of the frame to fill the opening found in Glock pistols. Front “lip” forms a tight, flush bond with the mag well to help make sure the mag goes where it should, smoothly. Keeps dirt and debris from finding its way inside the pistol and gives a clean, smooth look. Uses the lanyard hole for retention to snap firmly into place. Does not add extra rounds. abSPECS: Impact-resistant plastic, black. One per pack. Does not add extra rounds. Glock Plus Zero fits models 17 through 25, 31, 32, 34, 35, 37, and 38. Gen 4 Mid/Full Size fits Gen 4 models 17, 18, 19, 22, 23, 24, 31, 32, 34, 35, 37, and 38 only. Gen 4 Subcompact fits Gen 4 models 26, 27, 33, and 39 only. Other models fits the pre-Gen 4 Glocks indicated in the price lines below.

PEARCE GRIP

GRIP FRAME INSERT for GLOCK®

Fills The Opening In Glock Frames For Smoother Reloading

#092-000-009AU Glock Plus Zero Grip Frame Insert, 2K3M99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 4.99

#092-000-011AU G26/27/33/39 Grip Frame Insert, 2K3G99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4.99

#092-000-014AU G20SF/21SF Grip Frame Insert, 2K3J99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4.99

#092-000-031AU Gen 4 G20/21/41 Grip Frame Insert, 2K5F99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 6.99

#092-000-016AU G36 Grip Frame Insert, 2K3B99� � � � � � � � 4.99#092-000-022AU Gen 4 Mid/Full-Size Frame Insert,

2K3D99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4.99#092-000-023AU Gen 4 Subcompact Frame Insert,

2K3Q99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � � 4.99#092-000-030AU G42 Grip Frame Insert, 2K5K99� � � � � � � � 6.99

Ever since the Glock 17 first came out, aftermarket parts mak-ers have supplied a "grip plug" to

seal off the void in the back of the molded polymer grip frame behind the magazine well. They give your Glock a finished look down there, but...what if that space could be used for some-

thing really useful? Vickers's Grip Plug/Takedown Tool is a handy pin-punch tool for field stripping your Glock that conveniently stows in the grip cavity until you need it. As a bonus, it also serves as a mini magwell ramp and index point to aid in smooth, rapid magazine insertion. Exterior is fully radiused - won't snag on hol-ster or clothing. Of course, when inserted into the grip, the tool seals off the grip cavity to prevent dirt, sand, and mud from entering the trigger control components and possibly disabling the weapon. Fits G17/19/22/23/31/32/34/35, with separate models for Gen3 and Gen4 pistols. Gen4 comes with one base insert and 2 tools, one for pistols with backstrap inserts, one for pistols without them. ab

TANGODOWN VICKERS TACTICAL GRIP PLUG/TOOL for GLOCK®

Fills Void in Grip Behind Magwell - Always Have a Takedown Tool With You

Gen3

#100-019-808AU Grip Plug Tool for Gen3 Glocks, 9B11D99 � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 12.99

#100-023-864AU Grip Plug Tool for Gen4 Glocks, 9B15I99 � � � � � � � � � � � � � � � � � � � � � � � � � � � � 17.25

Gen4

ZEV TECHNOLOGIES

ENHANCED SOCOM SLIDE for GLOCK®

Practical Upgrades Plus Center-Zero Mounting

for an RMR Sight

SOCOM slides offer yet another variation on Glock® customization, with a lower ejection port to help prevent smoke stacks or other failures to fully eject. Machined from top-grade stainless steel to precise dimensions for

excellent fit and performance. Built-in mounting slot for a Trijicon RMR red dot sight in front of the factory rear sight puts the RMR at the center zero point of the slide. "Aggressive" serrations give you plenty of purchase to rack the slide under stress - ideal for competition. Even the top of the slide has these serrations, so you can cycle the slide quickly, regardless of where your hand contacts it - another benefit for the competition shooter. And, of course, these serrations give your gun an unusual appearance. Models for Gen3 and Gen4 G17 ("Z17" model) and G19 ("Z19" model), in Flat Dark Earth (FDE) and Titanium Gray (Ti Gray) ab

#100-022-944AU Enhanced SOCOM Z17 Gen3 RMR Slide, Ti Gray, 8B459A59 � � � � � � � � � � � $ 499.99

#100-022-949AU Enhanced SOCOM Z17 Gen4 RMR Slide, FDE, 8B459J59 � � � � � � � � � � � � � � 499.99

PIS

TO

L

PAGE 218 Office/Tech: 641-623-5401GUARANTEED. FOREVER.

SINCE 1939

BA

RR

ELS

FRA

ME

S/SL

IDE

S

Easy-to-install, specialized muzzle acces-sories give Glock shooters a choice of flash suppression or recoil control. Compensator’s side ports direct gasses 30 degrees rearward and out of the top ports, resulting in reduced felt recoil and muzzle jump. As a result, the shooter can remain centered on the target, allowing for quicker, more reliable follow-up shots. Integrated Allen screw indexes compensator for correct positioning. Flash Suppressor has longitudinal 6-port design that reduces muzzle flash, affording the shooter concealment and vision preservation in night-adapted environments. abSPECS: CNC-machined steel. Flash Suppressor - Black oxide finish. 1.6" (4cm) OAL. .750" (1.9cm) O.D. 1.1 oz (31.2g) wt. Fits pistols chambered in 9mm. ½" x 28 threads. Compensator - Parkerized , matte gray. 1.2" (34cm) OAL. 1" (2.5cm) wide, ¾" (1.9cm) high. 1.6 oz (45.4g). Available in 9mm with ½" x 28 threads and .40 S&W with 9/16" x 24 threads. Allen wrench and instructions included.

LONE WOLF

FLASH SUPPRESSORS & COMPENSATORS

Dynamic Recoil & Flash Control Options

#100-009-517AU 9mm Comp., ½" x 28, 2K59Q99 � � � � � $ 67.99#100-009-518AU .40 S&W Comp., 9/16" x 24, 2K58C99 � � 64.99#100-009-521AU 9mm Flash Supp., ½" x 28, 2K19K99 � � 20.99

Flash Suppressor

Compensator

Cover plate personalizes the look of your Glock and replaces the plastic, factory part for added strength. Installs and removes more easily than the factory cover plate for maintenance access. abSPECS: Machined aluminum, hardcoat anodized, matte black finish. Uni-versal fit for Glock pistols.

LIGHTNING STRIKE

COVER PLATE for GLOCK®

Durable Replacement To Factory Part Easy, Drop-On Installation

#642-000-016AU Cover Plate for Glock, 2D9B99 � � � � � � �$ 16.99

A standard-sized Glock® slide backplate with a unique dimpled pattern - kinda like golf-ball dimples - that gives your Glock a subtly different look. Made of hardcoat anodized alu-

minum, so it's substantially sturdier than the plastic backplate that came with your pistol from the factory. ab

ZEV TECHNOLOGIES

ALUMINUM SLIDE BACK PLATE for GLOCK®

Stronger Than Factory Part - Golfball Pattern Gives Your Pistol a Unique Look

#100-019-677AU Alum. Slide Back Plate, 8B17K48 � � � � � �$ 19.00

Durable, machined alumi-num slide plate replaces fac-tory plastic part and is laser etched with a distinctive dec-orative logo that dresses up your favorite Glock pistol with your own personal statement. Drop-in fit, so no modifications to the slide are required. Logos will not fade or wear off. Available with American Flag, Punisher , Jolly Roger, Bio-hazard, Smiley Face, or We The People logo. abSPECS: Machined aluminum, anodized, matte black finish with white logo. Fits all Glock pistol models.

SLIDE RACKER - Replacement slide plate has an aluminum extension that lets you rack the slide from behind with a fast pull of your fingers. Also helps you rack the slide in a confined space to clear a jam or reload while maintaining cover. Remove the two screws and flip the extension to the other side for right- or left-handed operation. Available in plain black or with American Flag logo.SPECS: Machined aluminum, anodized, matte black finish. Fits all Glock pistol models.#100-005-827AU Plain Black Slide Racker, 4C22L99 � � � $ 34.99#100-005-828AU US Flag Slide Racker, 4C22L99 � � � � � � 34.99

TACTICAL SUPPLY DEPOT

SLIDE PLATE for GLOCK®Functional, All-Metal

Construction; Personalizes Your Glock

#100-004-914AU US Flag Slide Plate, 4C16A99 � � � � � � � � $ 24.99#100-005-824AU Jolly Roger Slide Plate, 4C16C99 � � � � 24.99#100-005-825AU Biohazard Slide Plate, 4C16I99 � � � � � � 24.99#100-005-826AU Smiley Face Slide Plate, 4C16D99 � � � 24.99#100-006-901AU We The People Slide Plate,

4C16D99 � � � � � � � � � � � � � � � � � � � � � � � � � � 24.99

ab

The "Eagle's Talon" is an upgrade part that re-places your Buck Mark's factory extractor to give more reliable, positive extraction of spent cases.

The Buck Mark is an excellent rimfire pistol, but one of its weak spots is its extractor. Tandemkross's part eliminates this weakness through enhanced hook geometry that grabs the rim of each round securely - like an eagle snatching its prey - and won't let go until it's time for it to be ejected. The sharp hook holds the case rim securely through the entire firing cycle. Machined from hardened tool steel for reliable long-term service, and won't chip like the factory part is prone to do. Really boosts your pistol's reliability by preventing ejection failures that can be a disaster in competition or put a damper on the fun during a day of plinking. ab

TANDEMKROSS BROWNING BUCK MARK

EAGLE'S TALON EXTRACTORBoosts Your Pistol's Reliability By Ensuring

Positive, Consistent Case Ejection

#100-023-854AU Eagle's Talon Extractor, 1G00AFE � � � � � $ 9.99

Makes field stripping your Ru-ger .22 pistol faster and easier by enabling rapid disassembly with a single Allen wrench for routine cleaning and maintenance. Re-places the factory hammer and sticky bolt stop pin that make bolt removal a real chore. Replacement parts are precision machined from high-grade stainless steel to toler-ances that meet or exceed the fac-tory parts. Requires no permanent modification to your pistol; gun-smith installation recommended. Speed Strip 3.2 fits any genera-tion Mark series pistol and features hammer pivot bushing that helps reduce trigger pre-travel significantly and allows safe omission of magazine disconnect in Mark III pistols. abSPECS: Stainless steel, natural silver finish. Kit includes replacement hammer and bolt stop pin, plus Allen wrench and illustrated installation instructions. Mark I/II fits Ruger Mark I, II, and 22/45 pistols. Mark III fits Ruger Mark III pistol only. 3.2 Kit includes hammer pivot bushing and fits all Ruger Mark I, II, III, and 22/45 pistols.

MAJESTIC ARMS RUGER® MARK I/II/III

SPEED STRIP KITReplaces Factory Parts For Fast

Field Stripping & Cleaning

Mark I/II

#941-000-003AU Mark I/II Speed Strip Kit, 1D37M99� � � �$ 59.99#941-000-002AU Mark III Speed Strip Kit, 1D41P99 � � � � � 62.99#941-000-006AU 3.2 Speed Strip Kit, 1D70K99 � � � � � � � � � 74.99

3.2

Improved hook design helps ensure consistent extraction each and every time. Machined from tool steel then hardened to resist breakage and reduce wear for a lifetime of reliable operation. Includes extra-power spring for added reliability. Also fits Ruger® 10/22® rifle. abSPECS: Tool steel extractor, high-performance spring. Fits Ruger Mark I/II/III & 22/45 pistols and 10/22 rifles in .22 LR and .22 Magnum.

TACTICAL SOLUTIONS RUGER® MARK I/II/III™ & 22/45™

HEAVY DUTY EXTRACTORHardened Tool Steel

With Improved Hook For Reliable Extraction

#100-006-000AU Heavy Duty Extractor, 8K9E99 � � � � � � � $ 11.99

Steel extractor is machined using advanced EDM technology to ensure precise tolerances, then hardened to Rc 58-60 to help prevent premature wear. Extra long extractor hook is .005" closer to case rim for a positive, non-slip grip on

the case head. Made from A2 tool steel. abSPECS: A-2 tool steel, in-the-white. Hardened to Rc 58-60. Includes re-placement spring. Fits Walther P22.

VOLQUARTSEN WALTHER P22

EXACT EDGE EXTRACTORTuned & Hardened For Lasting

Performance

#930-000-053AU Exact Edge Extractor, 3Z17C99 � � � � � � $ 19.99

The "Halo" is an easy-to-grip pull-ring that clamps quickly and easily to your Ruger rimfire's bolt "ears" to make charging the pistol easier. With its simple, robust design, the Halo ensures fingers of any size can get the proper purchase on the bolt to cycle it smartly without slip-ping. Ambidextrous, so left- and right-hand-ed shooters get the same benefit. Makes your pistol look just a bit different from the other Ruger .22s at the range, too. Made of light-weight yet strong aluminum, so it doesn't mess up the gun's balance. Easily mounts to the bolt with no permanent alterations to the gun. Great for youths, competition shooters, and slightly less young shooters with weak or arthritic hands - anybody who doesn't want to take multiple swipes to charge a round or clear a jam. Separate models for Mark IV™/Mark III™ and older Mark II™. Both also fit associated 22/45™ vari-ants. ab

TANDEMKROSS RUGER® MARK II/III/IVTM

"HALO" CHARGING RINGGives You Extra "Purchase"

To Rack the Bolt

#100-023-848AU Halo Ring, Mark III/IV, Blk, 1G00EGA � �$ 49.99#100-023-849AU Halo Ring, Mark III/IV, Silver,

1G00LBL � � � � � � � � � � � � � � � � � � � � � � � � � � � 49.99#100-023-850AU Halo Ring, Mark II, Black, 1G00ERE � � � � 42.99

Tandemkross has put to-gether a kit of upgrades that will transform your 22/45 from a good .22 to a Dream GunTM. These parts fit any ANY Ruger Mark III 22/45. Stainless steel (308 alloy) Hammer Bush-ing lets the hammer move smoothly at the correct speed

for reliable hits on the cartridge rim. Allows you to safely remove the magazine disconnect, too, so ejected mags drop freely. Gun will also fire with a round in the chamber but no magazine - useful backup function for competition and self-defense. "Kanewolf" up-grade enables "slingshot" loading action rather than depressing the bolt release to close the bolt, which causes unnecessary wear on the bolt catch and bolt face. Kanewolf lets you charge the chamber just like on any modern semi-auto: by pulling back on the "slide". Does not affect last round hold open function. "Firestarter" Titanium fir-ing pin is 40% lighter than the factory steel pin for shorter locktime and less risk of moving the pistol between squeezing the trigger and the pin hitting the case rim. Titanium resists "mushrooming" that sometimes happens with steel firing pins, so it ensures positive primer strikes - and causes less deformation of case rim for positive extraction. "Eagle Talon" extractor machined from hardened tool steel with a unique hook design that grabs casings securely - like an eagle snagging its prey - and yanks 'em out, helping to reduce the incidence of failures-to-eject and "stove-pipe" malfunctions. Extended magazine release is longer and has a wider face than the factory part, so it's easier to locate and drop the mag on the first try. Also ensures full access to the release when you have thick target grips installed. Loaded chamber indicator replacement insert helps prevent some misfeeding and ejection problems, improves the appearance of your pistol, and simplifies cleaning. It does disable loaded chamber indicator feature, so check local laws. ab

TANDEMKROSS RUGER® MARK III 22/45TM

HIGH PERFORMANCE KITMultiple Upgrades That

Improve Reliability, Comfort & Aesthetics

#100-020-906AU Mark III 22/45 High Performance Kit, 1G94E49 � � � � � � � � � � � � � � � � � � � � � � � � � � �$ 99.99

The "Stealth" comp hides in plain sight: with its blocky, squared-off pro-file, it easily blends in with your Glock's squared-off slide. In fact, the Stealth mir-rors the Glock factory slide contour so

well, that when it's installed on a G19 or G23 (with a 9mm conversion barrel), the pistol easily fits in a holster designed for the G34/35. Two narrow ports running horizontally across the top, plus two smaller side ports, supplemented by two small side ports, vent combustion gases upward to counteract muzzle rise and reduce felt recoil. The Stealth is machined from high-grade 7075 T6 aluminum billet and given a durable, matte black hardcoat anodized finish. And it's de-signed to fit 9mm barrels with ½"-28 tpi threads (NOT for .40 S&W). The Stealth's attachment setscrews are hidden, so when it's installed, it offers an exceptionally clean, uncluttered appearance. Instructions and all necessary parts for the installation are included. abSPECS: 1.150" long x 1" wide x .785" tall.

PRIMARY MACHINE

STEALTH COMP FOR GLOCK®

Effective Control of Muzzle Rise, Plus a Clean, Futuristic Look

#100-024-393AU Stealth Comp for Glock, 7F00EPI � � � � $ 90.99

PAGE 219Orders: 800-741-0015order on the web

brownells.com

PIST

OL

BA

RR

ELS

BARREL FITTING All custom aftermarket barrels will need some fit-

ting. The amount required will depend on the tolerances allowed by both the barrel and slide makers, as well as the frame of the pistol. Some barrels may need the chamber cut to full depth after the barrel has been fitted. We carry a wide variety of files and stones to help with the fitting, and chambering reamers from Clymer and Manson Precision.

Stainless steel barrels drop into pouplar models of 9mm and .45 ACP semi-auto pistols and come with either metric or English unit threads that mate with different types of suppressors. Barrels are designed to install with no fitting required, and have rifling compat-ible with both jacketed and lead ammunition. All barrels come with knurled thread protectors for use when not using a suppressor. abSPECS: 416R Stainless steel, Black Isonite finish. LH = left-hand.

ADVANCED ARMAMENT

THREADED PISTOL BARRELS

STOCK # FITS CALIBER THREAD SIZE#276-000-031AU Glock 17 9mm Metric 13.5x1 LH#276-000-033AU Glock 17 9mm ½" x 28#276-000-032AU Glock 19 9mm Metric 13.5x1 LH#276-000-035AU Glock 21 .45 ACP Metric 16x1 LH#276-000-036AU Glock 21 .45 ACP .578" x 28#276-000-037AU S&W M&P Full-Size 9mm Metric 13.5x1 LH#276-000-038AU S&W M&P Full-Size 9mm ½" x 28#276-000-039AU S&W M&P Full-Size .45 ACP .578" x 28#276-000-040AU Springfield XD Service 9mm Metric 13.5x1 LH#276-000-041AU Springfield XD Service 9mm ½" x 28#276-000-042AU Springfield XD Service .45 ACP .578" x 28

— Advise # — AA Threaded Barrels, 6G208P99 � � � � � � $ 219.99

Barrels Feature Suppressor-Ready Threads

If you can break down your pistol for cleaning, then you can install one of these drop-in ready, match grade barrels. Machined from 416R stainless steel, with pulled broach rifling and a 1-10" twist, bar-rels are available in either a Standard configuration or as a fluted Mid-Line for enhanced cooling during those long range sessions. Non-Threaded barrels sit flush with slide and feature a deep beveled crown to protect the rifling. Threaded models come with ½"-28 threads and protector. Barrels are finished in either Stainless Steel, Black DLC (Diamond-Like Carbon), or Titanium Nitride (Gold). Will not fit Gen5 pistols. ab

AGENCY ARMS

MATCH-GRADE BARRELS for GLOCK® PISTOLS

A Drop-In Upgrade - The Quickest Way To Improve the Accuracy Potential of

Your Pistol

STOCK # FITS FINISH STYLE PRICESTANDARD LINE BARRELS

#100-024-648AU G17 Stnls Non-Threaded 1A00QIQ $ 160.00#100-024-632AU G17 Black Nitride Non-Threaded 1A00QKS $ 160.00#100-024-664AU G17 TiNi Non-Threaded 1A00BUD $ 160.00#100-024-650AU G17 Stnls Threaded 1A00DBH $ 170.00#100-024-634AU G17 Black Nitride Threaded 1A00MGG $ 170.00#100-024-666AU G17 TiNi Threaded 1A00FQQ $ 170.00#100-024-652AU G19 Stnls Non-Threaded 1A00KPE $ 160.00#100-024-636AU G19 Black Nitride Non-Threaded 1A160I00 $ 160.00#100-024-668AU G19 TiNi Non-Threaded 1A00PYE $ 160.00#100-024-654AU G19 Stnls Threaded 1A00MFG $ 170.00#100-024-638AU G19 Black Nitride Threaded 1A00BAF $ 170.00#100-024-670AU G19 TiNi Threaded 1A00AVE $ 170.00#100-024-656AU G34 Stnls Non-Threaded 1A00PGE $ 160.00#100-024-640AU G34 Black Nitride Non-Threaded 1A160A00 $ 160.00#100-024-672AU G34 TiNi Non-Threaded 1A00EZM $ 160.00#100-024-658AU G34 Stnls Threaded 1A00ESM $ 170.00#100-024-642AU G34 Black Nitride Threaded 1A170L00 $ 170.00#100-024-674AU G34 TiNi Threaded 1A00KXI $ 170.00#100-024-660AU G43 Stnls Non-Threaded1A128Q00 $ 160.00#100-024-644AU G43 Black Nitride Non-Threaded 1A00KAI $ 160.00#100-024-676AU G43 TiNi Non-Threaded 1A00BGD $ 160.00#100-024-662AU G43 Stnls Threaded 1A00HMD $ 170.00#100-024-646AU G43 Black Nitride Threaded 1A00MFC $ 170.00#100-024-678AU G43 TiNi Threaded 1A00BSB $ 170.00

MID-LINE FLUTED BARRELS#100-024-649AU G17 Stnls Non-Threaded 1A00NEH $ 200.00#100-024-633AU G17 Black Nitride Non-Threaded 1A00EMI $ 200.00#100-024-665AU G17 TiNi Non-Threaded 1A00CLK $ 200.00#100-024-651AU G17 Stnls Threaded 1A00EMA $ 210.00#100-024-635AU G17 Black Nitride Threaded 1A00DEF $ 210.00#100-024-667AU G17 TiNi Threaded 1A00QEN $ 210.00#100-024-653AU G19 Stnls Non-Threaded 1A00CSR $ 200.00#100-024-637AU G19 Black Nitride Non-Threaded 1A00AQK $ 200.00#100-024-669AU G19 TiNi Non-Threaded 1A00KAC $ 200.00#100-024-655AU G19 Stnls Threaded 1A00GLM $ 210.00#100-024-639AU G19 Black Nitride Threaded 1A00IUI $ 210.00#100-024-671AU G19 TiNi Threaded 1A00LEQ $ 210.00#100-024-657AU G34 Stnls Non-Threaded 1A00AQE $ 200.00#100-024-641AU G34 Black Nitride Non-Threaded 1A00MHK $ 200.00#100-024-673AU G34 TiNi Non-Threaded 1A00PAA $ 200.00#100-024-659AU G34 Stnls Threaded 1A210Q00 $ 210.00#100-024-643AU G34 Black Nitride Threaded 1A00BYB $ 210.00#100-024-675AU G34 TiNi Threaded 1A00EIP $ 210.00

Standard Threaded Stnls

Mid-Line Non-Threaded w/TiNi Finish

Mid-Line Non-Thread w/Black Nitride

If you're looking for a thread-ed barrel with match-grade ac-curacy for your G43, then ATI's

drop-in, stainless steel barrel is right up your alley! 1-10" broach-cut rifling gives superb accuracy with both jacketed and, and a bonus to help you keep down the cost of practice ammo, lead bullets. And it's fully chambered and throated to match-grade standards. Comes with a threaded cap to protect the muzzle when no de-vice is attached. Shooting a small pistol does not have to mean big groups! abSPECS: 416R stainless steel, natural polished finish. 1/2-28" muzzle threads.

AMERICAN TACTICAL

THREADED BARREL for GLOCK® 43Comp/Suppressor-Ready,

Plus Match-Grade Accuracy & Lead-Bullet Friendly

#100-018-092AU Threaded Barrel for Glock 43, 3E134I99 � � � � � � � � � � � � � � � � � � � � � � � � � $ 143.99

Machined from 416 stainless steel bar stock, stock length re-

placement barrels for your Glock® have fully supported chambers and broach cut rifling with a 1-16" twist. Barrels have a heat treated hardness of 39 to 43 RC and a tensile strength of 180,000 psi. Due to the close tolerances and variances in handguns, these “semi fit” barrels may require some fitting. abSPECS: Stainless steel, hardened to 39 to 43 Rc. Fits Glock handguns.

BAR-STO

GLOCK SEMI-FIT BARRELSBroach Cut Rifling For

Improved Accuracy

STOCK # MODEL CALIBER PRICE#100-015-626AU 17 9mm Luger 7B250N99 $ 281.99#100-015-627AU 19 9mm Luger 7B232A99 $ 251.99#100-015-628AU 20 10mm Auto 7B232K99 $ 251.99#100-015-629AU 21 .45 ACP 7B232I99 $ 251.99#100-015-652AU 22 .40 S&W 7B232B99 $ 251.99#100-015-653AU 23 .40 S&W 7B232K99 $ 251.99#100-015-654AU 34 9mm Luger 7B244L99 $ 268.99#100-015-655AU 35 .40 S&W 7B243N99 $ 263.99

STOCK # FITS FINISH STYLE PRICE#100-024-661AU G43 Stnls Non-Threaded 1A00HLN $ 200.00#100-024-645AU G43 Black Nitride Non-Threaded 1A00JPL $ 200.00#100-024-677AU G43 TiNi Non-Threaded 1A00FKB $ 200.00#100-024-663AU G43 Stnls Threaded 1A210D00 $ 210.00#100-024-647AU G43 Black Nitride Threaded 1A00JLD $ 210.00#100-024-679AU G43 TiNi Threaded 1A00EKE $ 210.00

Built to the same specifica-tions as your original factory barrel, our replacement barrels enable you to restore the accuracy of pistols with shot out barrels, without going to a gunsmith. These barrels, including the models for Glock®

pistols have conventional rifling with a 1-10" twist to handle cast lead or jacketed bullets with accuracy. Machined from 416-R stainless steel, these barrels are nitride treated inside AND out for corrosion resistance and longevity. An 11° target crown protects the end of the rifling from accuracy-compromising damage. Threaded muzzle models available with 1/2"-28 tpi threads. These barrels are ready-to-install in your pistol, with no additional fitting required. Glock models fit Gen 1-4. Smith & Wesson M&P fit both original M&P and M2.0 models. ab

PISTOL BARRELSDrop-In Accuracy

Upgrade With No Gunsmithing Required

#100-026-209AU Browning Hi-Power 9mm Bbl, 1D103H99 � � � � � � � � � � � � � � � � � � � � � � � � �$ 130.99

#100-026-208AU Browning Hi-Power 9mm Bbl, Threaded, 1D103B99 � � � � � � � � � � � � � � � 130.99

#100-026-202AU Glock G17 Gen1-4 9mm Bbl, 1D113B99� � � � � � � � � � � � � � � � � � � � � � � � � � 149.99

#100-026-203AU Glock G17 Gen1-4 9mm Bbl, Threaded, 1D116Q99 � � � � � � � � � � � � � � � 137.99

#100-026-200AU Glock G19 Gen1-4 9mm Barrel, 1D129C99 � � � � � � � � � � � � � � � � � � � � � � � � � 149.99

#100-026-201AU Glock G19 Gen1-4 9mmBarrel, Threaded, 1D117H99 � � � � � � � � � � � � � � � 134.99

#100-026-204AU SIG P320 Full-Size 9mm Barrel, 1D98P99 � � � � � � � � � � � � � � � � � � � � � � � � � � 126.99

#100-026-205AU SIG P320 Full-Size 9mm Barrel, Threaded, 1D103H99 � � � � � � � � � � � � � � � 130.99

#100-026-206AU Smith & Wesson M&P Full-Size 9mm Barrel, 1D98N99 � � � � � � � � � � � � � � � � � � � 126.99

#100-026-207AU Smith & Wesson M&P Full-Size 9mm Barrel, Threaded, 1D103C99 � � � � � � � � 130.99

Standard & SAAMI

The Brownells Extended Bar-rel for Glock® 19 is designed to

work hand-in-glove with our extended slides for the popular com-pact 9mm pistol. Due to changes in the slide-to-frame geometry caused by mating the long slide on the compact Glock 19 frame, a factory Glock 17 slide will not work with our slide. This extended barrel is correctly configured to ensure that your new "long slide" G19 functions perfectly. This extended barrel and the slide work to-gether to give you a longer sight radius for more accurate shooting and better recoil control - and a pistol that’s more comfortable to shoot all around. Our Extended Barrel for Glock 19® is available with a Plain muzzle or Threaded (1/2"-28 tpi) to accept a compensator or silencer. Easy drop-in installation. Corrosion-resistant 416R stain-less steel with durable black Nitride finish for excellent resistance to surface wear. 1-10" right-hand 6-groove rifling. Threaded model has ½"-28 muzzle threads. These barrels are precision machined to ensure an exact fit to drop right into your pistol’s extended slide and preserve the superior reliability and performance your expect from your Glock® 19. ab

19LS EXTENDED BARREL for GLOCK® 19

Correct Barrel for Your Custom G19 With Extended Slide

#078-000-383AU 19LS Barrel for Gen3 Glock® 19, 6H151M99 � � � � � � � � � � � � � � � � � � � � � � � � $ 169.99

#078-000-384AU Threaded 19LS Barrel for Gen3 Glock® 19, 6H159A99 � � � � � � � � � � � � � � 179.99

Swap your 9mm M&P's factory barrel for one of these and enjoy an immediate jump in accuracy and performance. The folks at Apex Tactical have engineered a barrel capable of shooting groups as small as a 11/2" at 25 yards. These 9mm barrels have a 1-10" twist and are available in either 4.25" or 5" lengths. Semi Drop-In replaces factory barrel and may require some minor fitting before installation. Gunsmith Fit requires fitting by a profes-sional gunsmith. Threaded models maintain the same features and also have an extended muzzle with 1/2"-28 tpi threads to accept a compensator or sound suppressor. Screw-on thread protector in-cluded. .40-to-9mm Conversion Barrels do what the name says they do: converts an M&P40 to shoot 9mm Luger. These barrels fit all M&P40 pistols, including the M&P 2.0 and are optimized to work best with bullet weights of 115 gr to 147 gr. 1-10" rifling. A 9mm magazine is required to complete the conversion (not included). ab

APEX TACTICAL SMITH & WESSON M&P

STAINLESS STEEL 9MM BARRELS & .40-TO-9MM CONVERSION BARRELSBoosts Accuracy Of Your M&P -

1.5" Groups 75 Yards

#100-018-361AU 4.25" Semi Drop-In S&W M&P Barrel, 7F171P39 � � � � � � � � � � � � � � � � � � � � � � � � � $ 189.95

100-023-282AU 4.25" Threaded Semi Drop-In M&P Barrel, 7F229P29 � � � � � � � � � � � � � � � � � 259.95

#100-018-360AU 5" Semi Drop-In S&W M&P Barrel, 7F171P39 � � � � � � � � � � � � � � � � � � � � � � � � � 189.95

100-023-281AU 5" Threaded Semi Drop-In M&P Barrel, 7F229J29 � � � � � � � � � � � � � � � � � � 259.95

#100-018-363AU 4.25" Gunsmith Fit S&W M&P Barrel, 7F171I39 � � � � � � � � � � � � � � � � � � � � � � � � � � 189.95

100-023-280AU 4.25" Threaded Gunsmith Fit M&P Barrel, 7F229P29 � � � � � � � � � � � � � � � � � 259.95

#100-018-362AU 5" Gunsmith Fit S&W M&P Barrel, 7F171F39 � � � � � � � � � � � � � � � � � � � � � � � � � 189.95

100-023-279AU 5" Threaded Gunsmith Fit M&P Barrel, 7F229I29 � � � � � � � � � � � � � � � � � � 259.95

100-023-825AU 4.25" Semi Drop-In .40-to-9mm Conversion M&P Bbl, 7F174E49 � � � � 189.99

100-023-799AU 5" Semi Drop-In .40-to-9mm Conversion M&P Bbl, 7F174Q49 � � � � 189.99

100-023-798AU 4.25" Gunsmith-Fit .40-to-9mm Conversion M&P Bbl, 7F174M49 � � � � 189.99

100-023-797AU 5" Gunsmith-Fit .40-to-9mm Conversion M&P Bbl, 7F174B49 � � � � 189.99

Items

PAGE 220 Office/Tech: 641-623-5401GUARANTEED. FOREVER.

SINCE 1939

PIS

TO

LB

AR

RE

LS

A great starting point for your next custom build, or just a refresh of a gun with a shot-out barrel, these drop-in barrels are care-fully engineered, meticulously ma-chined, and exhaustively tested to provide top-notch performance.

Machined from triple stress-relieved, GBQ 4150 carbon steel for a tighter-than-OEM fit, these barrels deliver a more precise lockup with a greater accuracy potential. Barrels have an 11° target crowned muzzle to ensure the bullet stays on a true trajectory and are avail-able with either a standard muzzle or with ½"-28 tpi muzzle threads. The SAAMI-spec chamber and 1-10" twist conventional rifling read-ily handles any type of projectile - jacketed, heavy subsonics, even cast-lead practice bullets. These barrels fit Gen1 through Gen4 pistols. Choose from a Plain barrel for a traditional look or a Flame Fluted barrel that not only dissipates heat quicker, but it adds an ultra-radical look to your gun. These show stopping barrels have a hard, black Nitride finish for superb resistance to corrosion and surface wear. ab

FAXON FIREARMS

MATCH-GRADE BARRELS FOR GLOCK® 17/19/34

Tight, Slop-Free Fit for Superior Accuracy Potential

#100-026-101AU Glock G17 Gen1-4 9mm Bbl, Threaded, 1D141A55 � � � � � � � � � � � � � � � �$ 141.55

#100-026-105AU Glock G17 Gen1-4 Flame 9mm Barrel, 1D179I55 � � � � � � � � � � � � � � � � � � � 179.55

#100-026-106AU Glock G17 Gen1-4 Flame 9mm Barrel, Threaded, 1D189M05 � � � � � � � � 189.05

#100-026-100AU Glock G19 Gen1-4 9mm Barrel, Threaded, 1D132C05 � � � � � � � � � � � � � � � 132.05

#100-026-103AU Glock G19 Gen1-4 Flame 9mm Barrel, 1D170D05 � � � � � � � � � � � � � � � � � � 170.05

#100-026-104AU Glock G19 Gen1-4 Flame 9mm Barrel, Threaded, 1D179P55 � � � � � � � � � 179.55

#100-026-102AU Glock G34 Gen1-4 Competition 9mm Barrel, Threaded, 1D151L05 � � � � 151.05

#100-026-107AU Glock G34 Gen1-4 Flame 9mm Barrel, 1D189G05 � � � � � � � � � � � � � � � � � � 189.05

#100-026-108AU Glock G34 Gen1-4 Flame 9mm Barrel, Threaded, 1D198B55 � � � � � � � � � 198.55

Flame Threaded

Gemtech's threaded barrels set you up for proper and straight-forward mounting of a sound suppressor on your pistol. These premium extended/threaded barrels are designed for drop-in fit to your pistol's slide and feature a matte black oxide finish that is cor-rosion resistant for lasting durability and a compatible look. Bores have been gauged to ensure perfect alignment of the mounted sup-pressor with the land-and-grooves. Beretta 92 fits 92SB, 92F, 92FS, 92A1, 90-Two, Vertec, Brigadier, and Elite. Glock barrels are Gen4 compatible. All barrels come with a thread protector with easy-to-grip knurled outer surface. ab

GEMTECH

THREADED PISTOL BARRELS

#100-023-055AU Beretta 92 Threaded Barrel, 1/2"-28, 1A208C99 � � � � � � � � � � � � � � � � � � � � � � � � $ 208.99

#100-023-671AU Glock 17 Threaded Barrel, 1/2"-28, 1A171I43 � � � � � � � � � � � � � � � � � � � � � � � � � � 193.99

#100-023-672AU Glock 19 Threaded Barrel, 1/2"-28, 1A171L43 � � � � � � � � � � � � � � � � � � � � � � � � � 193.99

#100-023-673AU Glock 21 Threaded Barrel, .578"-28, 1A171N43 � � � � � � � � � � � � � � � � � � � � � � � � � 193.99

Mounting a Suppressor Just Got Easier

Restore or customize your High Standard pushbutton, take-down pistol with a factory replacement barrel. All barrels are drilled and tapped for High Standard Universal Scope Mount (#430-000-122). Models with front sight cut or tap, as well as cuts for muzzle stabilizer, are noted in chart. Sight not included. abSPECS: Steel, blued, gloss or matte finish. Available in .22 LR and .17 High Standard (.17 PMC/.17 Aguila) calibers and three contours: Round (R), Fluted (F), and Slab-Sided (S).

HIGH STANDARD

FACTORY PISTOL BARRELS

STOCK # LENGTHCONTOUR/

FINISHSTAB.CUT

SIGHT CUT PRICE

.22 LONG RIFLE#430-000-135AU 41/2" S/Gloss N Tapped 3D143K99 $ 167.99#430-000-107AU 51/2" R/Gloss Yes Dovetail 3D132L99 $ 154.99#430-000-136AU 51/2" S/Matte N Tapped 3D141F99 $ 164.99#430-000-126AU 51/2" S/Gloss N Tapped 3D227I99 $ 264.99#430-000-124AU 51/2" Bull R/Matte Yes Dovetail 3D196D99 $ 227.99#430-000-109AU 51/2" Bull R/Matte N Dovetail 3D118F99 $ 138.99#430-000-110AU 51/2" Bull S/Matte N No 3D112K99 $ 130.99#430-000-125AU 71/4" F/Matte Yes Dovetail 3D224A99 $ 260.99#430-000-123AU 10"

SilhouetteR/Matte N No 3D188P99 $ 202.99