Cw 2015 Build Info
-
Upload
mick-thomson-rc -
Category
Documents
-
view
214 -
download
0
Transcript of Cw 2015 Build Info
-
8/9/2019 Cw 2015 Build Info
1/13
1 | P a g e
Resolved CPRs
CAMWorks 2015SP0.1
* Please refer to Whats New PDF document for details regarding enhancements in CAMWorks 2015.
Sr.No.
CPRNumber
Help DeskID
Area Description
1.CW-49400
CW-48814
11-3494
11-3237License
The CAMWorks License Manager would stop working on a client
machine whenever the user clicked on Ok after providing the server
name and port details.
2. CW-48719 11-3191 UI
In the Italian version of CAMWorks 2015 Beta version, in the UI
displayed for interactively inserting a Multi Surface Feature, the icons
for the Face Select Option are overlapping and the selection menu is
unstable.
3. CW-48714 11-3184 System
While installing CAMWorks 2015 SP0, user encounters an error
message which states that the supported version of SOLIDWORKS or
CAMWorks Solids was not found installed. This error message is
displayed despite supported version of SOLIDWORKS and CAMWorksSolids having been installed. The installation however gets completed
successfully.
4. CW-48698 11-3145 License
The license borrowed on the client machine for one or more modules
of CAMWorks fails to initialize when it is disconnected from the
network. Instead, CAMWorks starts in Demonstration mode.
5. CW-48628 11-3107 System
If user installs CAMWorks 2015 SP0 on a system with SOLIDWORKS
2015 on which no CAMWorks version was previously installed, then
CAMWorks fails to generate toolpaths for any part.
6. CW-48615 11-3085 TechDB
In Mill machines with rotary axis, the mode for rotary axis should be
set to 'Fixed' for all features except wrapped features. Currently this is
being controlled by the settings made in TechDB and the user cannot
change them in CAMWorks.
7. CW-48582 ---- Toolpath
For the specific part, toolpaths were generated successfully in
CAMWorks 2014 version. In the CAMWorks2015 Beta version, the
application crashes when user tries to generate the same toolpaths.
8. CW-48248 11-2906 Operation
In CAMWorks 2014 SP 2.3 and CAMWorks 2015 SP0, when user tries to
save the operation plan of Face Feature for the specific part, it causes
SOLIDWORKS to crash.
9. CW-47475 11-2472 Support
Users are unable to utilize the Help option to check for Service Pack
updates. When they click on the Check button, they receive the errormessage that they are unable to connect to the Service Pack Server -
even though there is an internet connection.
-
8/9/2019 Cw 2015 Build Info
2/13
2 | P a g e
CAMWorks 2015SP0
Sr.
No.
CPR
NumberCAMWorks
2015 VersionHelp
Desk IDArea Description
1. CW-47786 SP0 11-2638 Post
For a turn operation, if the user inserts a new feed rate byediting the tool path, then upon posting the newly added
feed rate is not reflected in the posted output. This was
working correctly in CAMWorks 2013.
2. CW-47748 SP0 ---- UI
In the Japanese language version of CAMWorks, for
Threading operations in Turn mode, the order of the two
options displayed in the Program point dropdown list in
Thread tab is reverse to the order displayed in the English
version of CAMWorks.
3. CW-47650 SP0 11-2423 PostThe post variable TOOL_PROTRUSION posts values only
for Mill operations but not for Turn operations.
4. CW-47617 SP0 11-2545 Rebuild
In CAMWorks 2014, the yellow exclamation mark displayed
on the feature which is not in sync with the SOLIDWORKS
part is not removed even after the user manually doing a
full rebuild and the feature is also not updated as per the
SOLIDWORKS part. This behavior is seen with MS Hole
features.
5. CW-47534 SP0 11-2477 Rebuild
For the specific Wire EDM part for which features and
operations have been generated, if the dimension of one
of the sketches is updated and Full Rebuild subsequently
done, the yellow exclamation mark is still visible over the
feature icons indicating that the feature is out of sync with
the part model.
6. CW-47518 SP0Beta2015-
USFeatures
While interactively inserting an open profile feature, the
direction of cut specified by the user is not assigned to the
feature for the first time. The user will have to edit the
feature again and reassign the direction of cut. Only then
the user assigned direction of cut is applied to the feature.
7. CW-47511 SP0 11-2354 Post
For the specific Mill-Turn part, the posted NC code for the
Pattern type toolpaths of Wrapped Open Profile feature
outputs wrong Angular values between instances.
8. CW-47471 PR2 11-2470 API
When executing the API macro
"Post_Setup_Name_Full_Name.swp", if a post operation isthe first operation in the mill part setup then, upon
executing the command 'setup.PostProcess', the output
file generated is empty.
9. CW-47391 SP0Beta2015-
USToolpath
For a VoluMill Roughing toolpath, if an Avoid area is
defined using a sketch then, is not considered for
avoidance in the generated toolpath.
-
8/9/2019 Cw 2015 Build Info
3/13
3 | P a g e
Sr.
No.
CPR
NumberCAMWorks
2015 VersionHelp
Desk IDArea Description
10. CW-47384 PR2Beta2015-
USUI
For a turn part, when the stock type is changed to bar
stock from the SOLIDWORKS part type, then the stock
display is reset to wireframe in the display area. Also, if the
stock type is again reset to SOLIDWORKS part and the
current part is selected for stock, the available
configuration list becomes empty.
11. CW-47382 SP0Beta2015-
USUI
For defining the X Axis machining direction, an entity can
be selected. However, after closing the dialog box and
reopening, the entity that was selected does not get
highlighted in the graphics area. Due to this, user cannot
recognize which entity he has selected earlier.
12. CW-47325 PR2 11-2430 Post
For Turn operations, the Post variable
TOOL_CORNER_RADIUS is getting populated with Turn Drill
and Center Drill Diameter values.
13. CW-47278 SP0Beta2015-
EMEAAPI
Add new APIs which would let the user know, if a
CAMWorks feature has failed during the rebuild routine
and whether tool paths can be generated for the
operations in CAMWorks operation tree.
14.CW-47197
CW-45025SP0 11-1346 Setup Sheets
The parameter of "Define Coolant by Tool" is not present
in the Access based Setup Sheet or XML based Setup
Sheet.
15. CW-47187 PR2 11-2343 Help
In the Help documentation for TechDB, there is no
documentation provided on how to delete Tool Cribs
within the TechDB.
16. CW-47051 PR1 11-2308 Toolpath
For the specific Turn part with OD feature, the Roughing
Toolpath gouges the stock when Final Cut Amount is set as
0mm.
17. CW-47020 SP0 11-2282 Simulation
Contour Milling Toolpaths with helical moves are not being
simulated correctly in CAMWorks 2014 version. It worked
correctly in CAMWorks 2012 version.
18. CW-47016 PR211-2273
11-2420Features
If a part created in CAMWorks 2013 containing multiple
circular pockets with tapers is opened in CAMWorks 2014,
the user is prompted for rebuild. Even after selecting
"Light" rebuild, the earlier defined circular pockets get
deleted. Also, the user will not be able to define the same
features again by choosing multiple in 2.5 axis feature
wizard.
19. CW-46979 SP0 11-2248 Toolpath
For the specific Turn part, the ID Bore Rough toolpath
gouges the part when it is generated using the Variable
Allowanceoption enabled (with Radial and Axial
allowance having different values). Toolpath is correct if
Radial and Axial allowance values are equal.
-
8/9/2019 Cw 2015 Build Info
4/13
4 | P a g e
Sr.
No.
CPR
NumberCAMWorks
2015 VersionHelp
Desk IDArea Description
20. CW-46942 PR2 11-2233 Features
In CAMWorks 2014 SP2, the Face feature recognized using
Automatic Feature Recognition (AFR) in Turn module
includes the undercut features available on the part, which
is incorrect. This was working correctly in CAMWorks 2012.
21. CW-46887 SP0 11-2194 SupportThe email address given on the Enhancement Request
Form needs to be corrected to [email protected].
22. CW-46886 SP0Beta2015-
EMEAToolpath
For the specific pat, the Leadin and Leadout for Contour
Mill Operation is defined at the center of the segment.
However, the toolpath generated is not as per the assigned
Leadin and Leadout values.
23. CW-46845 PR2 Beta2015 UI
In the Operation Parameters dialog box, on the Lead
In/Out tab, when the Leadout type is selected as Same as
Leadin, then the preview panel does not display updated
images to correspond with the image for Leadin type.
24. CW-46844 PR2Beta2015-
EMEAUI
The icon provided for New Feature command does not
visually correspond to other icons on the Command
Manager. The icon needs to be modified in order to
visually sync it with other icons.
25. CW-46831 Beta 2Beta2015-
EMEAOperation
For Multiaxis operations, if parameters are modified on the
Gouge Checking tab of the Operations Parameters dialog
box, then CAMWorks doesnt prompt a Toolpath
Regeneration message on closing the dialog box.
26.CW-46804CW-46781
CW-46753
CW-46740
Beta 2 Beta2015 ConfigurationIn CAMWorks 2015 Beta1, for Mill Parts, when stock isdefined by using another configuration of the part being
machined, then SOLIDWORKS crashes. This is not observed
is Turn module.
27. CW-46803 Beta 2Beta2015-
EMEAFeature
Whenever a Hole group feature defined using a sketch is
deleted and restored, then the hole features are restored
as individual features. Upon doing edit definition of such
restored features, only a single hole feature is displayed in
the graphics area although the selected entities list shows
the name of the sketch used to define the group feature.
28. CW-46802 PR1 Beta2015-EMEA
Toolpath
If a corner round tool is used to machine the top fillet of a
feature and the output through option is set to 'Tip', thenthe resultant toolpath gouges the feature. The gouge is not
seen when the output option is set as 'Tangent'.
29. CW-46801 PR1Beta2015-
EMEASystem
CAMWorks Configurations are not supported for 2.5X
Limited License module type. It should be supported for
this License module also.
-
8/9/2019 Cw 2015 Build Info
5/13
5 | P a g e
Sr.
No.
CPR
NumberCAMWorks
2015 VersionHelp
Desk IDArea Description
30. CW-46799 PR1Beta2015-
EMEAToolpath
For the specific Mill part, the VoluMill roughing operation
ignores islands created using sketches.
31. CW-46797 Beta2015-EMEA
Toolpath
In CAMWorks 2015 Beta, for the specific part, the VoluMill
toolpath generated for the Roughing operation gouges 3
circular islands.
32. CW-46795 Beta 2Beta2015-
EMEAFeature
While interactively inserting a 2.5 Axis Mill feature with
islands, when user attempts to define Side Taper for the
Island Entities, the error message An unsupported
operation was attempted is displayed and the 2.5 Axis
Feature Wizard dialog box closes.
33. CW-46793 PR2Beta2015-
EMEAUI
While interactively inserting a 2.5 Axis feature, the End
condition is reset to default values if the user proceeds to
the next dialog in the Wizard and then returns back to the
end condition dialog box.
34. CW-46788 Beta 2Beta2015-
EMEAOperation
While creating a new turn operation, the user can select
tools from the new operation user interface. The available
tool list doesnt get updated when the user changes the
operation type by using the Back button.
35. CW-46771 Beta 2Beta2015-
EMEAAssembly
For the specific assembly file, when user edits the machine
definition, CAMWorks displays an error message Rotary
and Tilt axis cannot be parallel even though these axis are
not parallel. This error message was not observed in
CAMWorks 2014 version.
36. CW-46761 Beta 2 11-2096 Toolpath
For the specific 2.5 Axis Mill Part the Rough Mill toolpath
generated with a stepover of 40% or above and withpattern of pocket out, does not machine the feature
completely.
37. CW-46750 PR2 11-2161 Operation
For Engrave operations, Spline Deviations defined at global
level gets applied. The ability to override this global value
by defining Spline Deviation at operation level is disabled.
In specific cases, it can lead to the engrave toolpath to be
broken into too many segments.
38. CW-46720 SP0 11-2123 Assembly
In assembly mode, if the origin of the Mill par Setup is set
as Top Center and a Coordinate System is selected in the
Machine Definition, then for operations listed under the
Mill Part Setup, the min and Max values of X should ideallybe with respect to the Top Center of the Mill Part Setup.
Instead, these values are derived based on the Coordinate
System in Machine Definition.
-
8/9/2019 Cw 2015 Build Info
6/13
6 | P a g e
Sr.
No.
CPR
NumberCAMWorks
2015 VersionHelp
Desk IDArea Description
39. CW-46718 PR2 11-2124 Operation
If user switches to an alternate Tool Crib after a part has
been programmed and selects the Prompt option, then
CAMWorks displays a dialog to assign tools to the
operations from the new tool crib. However, no tools are
listed to choose from.
40. CW-46649 SP0 11-2126 Toolpath
For Mill parts having taper features needing external
threading, the toolpath passes of the thread milling cut the
feature in the reverse method i.e. the resultant toolpath
cuts the final pass of the thread in the beginning. This
behavior is not seen with thread milling done for features
having no taper.
41. CW-46631 Beta 2 11-2116 Post
When a multi axis mill operation with number of axis set to
3, is post processed, the values of clearance plane do not
get posted correctly. The user defined values for clearance
plane are not considered.
42. CW-46610 PR1 11-2111 Features
In mill parts, when Extract Machinable Features is done the
pockets with chamfer on top are detected as tapered
feature. The taper angle is shown as 90 degrees. However,
the user will not be able to use the option of 'Toolpath
center with or without compensation' for such features.
But the option will be available for interactively inserted
features.
43. CW-46609 Beta 2 11-2110 Features
When chamfer is present on a Mill parts edges, then the
Automatic Feature Recognition doesn't recognize the face
feature.
44. CW-46599 PR2 11-2079 Features
For the specific part, when user tries to generate Turn
features using Automatic Feature Recognition with
Revolved Section option, the features generated using a
Mill-Turn machine and Turn machine are different. Results
in both cases are unsatisfactory.
45. CW-46540 SP0 11-2055 ToolpathFor the specific part, the Contour Mill toolpath defined for
the Curve Feature is not following the curve definition.
46. CW-46497 PR2 11-2037 VoluMillFor the specific part, VoluMill does not avoid islands
defined using a sketch.
47. CW-46491 SP0 11-1982 Assembly
For the specific Assembly file, if user updates the Tool Crib
and tries to save the part, then user is unable to save the
CAMWorks data and CAMWorks crashes.
48. CW-46466 PR1 11-2023 Toolpath
For the specific turn part, the Groove finish toolpath is
generated in Turn mode but cannot be generated in Mill-
Turn mode.
-
8/9/2019 Cw 2015 Build Info
7/13
7 | P a g e
Sr.
No.
CPR
NumberCAMWorks
2015 VersionHelp
Desk IDArea Description
49. CW-46457 Beta 2 11-2014 TechDB
Within the TechDB, in the Tapping- Rolling Taps database,
for some tap conditions, the values of the Tap drill
diameter is larger than the Major diameter (D1) of tap.
Also, for some tapping conditions, no operations have
been defined in mill mode.
50. CW-46410 SP0 11-1986 Features
For the specific part, when a Mill Part Setup is inserted and
Recognize Features command executed, features are
correctly recognized. However, on inserting another Mill
Part Setup in the opposite direction and executing the
Recognize Features command, the features in the earlier
setup indicate a potential rebuild failure.
51. CW-46365 Beta 2 11-1971 Operation
If the user selects Cancel button in the operation
parameters dialog box after selecting a new tool from the
tool crib, then the changes made to the tool should not be
retained. The older tool and its dimensions should be
retained.
52. CW-46321 Beta 1 11-1955 UI
Add the parameter of body length of the corner round tool
in the preview window. At present the parameter is seen in
the UI of the tool tab as L5.
53. CW-46314 Beta 1 11-1954 Configuration
When renaming SOLIDWORKS Configurations, when user
switches to another Configuration, the configuration that
was renamed reverts back to the original name.
54. CW-46308 Beta 2 11-1949 Toolpath
In CAMWorks 2014 SP 2.1, the Contour Mill toolpath for
rest machining ends up machining the whole feature. This
functionality is working correctly in CAMWorks 2014 SP1.
55. CW-46269 SP0 11-1929 SimulationFor specific mill part, large arc moves are seen during stepthrough simulation. However, the posted NC code is
satisfactory as per the feature geometry.
56. CW-46247 Beta 1 11-1918 Feature
If the dimension of the fillet is less than 0.0026 Inch, then
user cannot pick the fillet entity for interactively defining
an Open Profile feature.
57. CW-46161 Beta 1 11-1608 Post
Change the error message which is shown when posting is
done using a Mill Turn post supporting X positive co-
ordinates only to Error: Exceeded X Minus Limit of X0. Post
may still output the X coordinates.
58. CW-46089 Beta 1 11-1807 Feature
In Mill Assembly Mode, when creating 2.5 Axis Features
interactively using assembly sketches, if the user proceeds
with interactive insertion of the next feature without
closing the New 2.5 Axis Feature dialog box, then the
orientation and placement of the resultant feature is
incorrect.
-
8/9/2019 Cw 2015 Build Info
8/13
8 | P a g e
Sr.
No.
CPR
NumberCAMWorks
2015 VersionHelp
Desk IDArea Description
59. CW-46085 Beta 1 11-1826 TechDB
When Additional Amount for Leadin is defined in TechDB
and Generate Operation Plan is done then, the set values
for additional amounts are not reflected in CAMWorks.
60. CW-46026 Beta 1 11-1775 Toolpath
For the specific part machined using CAMWorks 2014
version, the multiaxis toolpath is gouging the part. This
toolpath didnt gouge the part in CAMWorks 2012 version.
61. CW-45992 SP0 11-1774 Translation
In Turn module, for Thread parameter, the choice of
"Program point" -"Tool nose Center" & "Tool nose tip" is
different for Japanese version of CAMWorks when
compared to English Language version.
62. CW-45977 Beta 1 11-1768 Feature
In CAMWorks 2014 SP2.1 version, when a 2.5 Axis Open
Profile feature with the side wall taper is interactively
inserted then, the resultant feature is incorrect.
63. CW-45823 Beta 1 11-1715 UI
In the Post Processor tab of the Machine node dialog box,
the width of the Post Processor selection box needs to be
increased.
64. CW-45679 Beta 2 ---- Toolpaths
The Entry Hole and Entry Drill toolpaths defined for a 2.5
axis operation shouldnt be modified when generate
toolpath command is executed on the 2.5 axis operations
without changing any parameter.
65. CW-45653 Beta 1 11-1629 Post
The post operations do not get post processed when
selected with other operations and posted. But when thepost processing is done for all the operations from
CAMWorks toolbar, they get prost processed.
66. CW-45652 Beta 1 11-1628 UI
When a turn feature is being inserted using Revolved
Section method then, the Turn Section Plane Angle field
should be disabled as it is applicable only to Plane Section
method.
67. CW-45543 Beta 2 11-1552 TechDBFor the Drill Tool with TechDB ID 435, the incorrect tool
description is given. It should be updated to 5/64.
68. CW-45539 Beta 1 11-1549 TechDBIn the Setup tab of the Turn and Mill-Turn MachineDefinition Forms, the 'Global Rotary Retract Plane' field
needs to be removed as it serves no purpose.
69. CW-45456 Beta 1 11-1512 UI
For Contour Mill operations, Additional Amt. fields for
Leadin/Leadout should be disabled when in Units mode.
They should be active only in percentage mode.
-
8/9/2019 Cw 2015 Build Info
9/13
9 | P a g e
Sr.
No.
CPR
NumberCAMWorks
2015 VersionHelp
Desk IDArea Description
70. CW-45397 Beta 2 11-1467 Toolpath
For the specific Mill Part, toolpath is not generated for a
Pattern Project operation with pattern type set to
Flowline.
71. CW-44978 PR1 11-1308 PostPost Flags ID and OD do not work, when Canned Cycle
Output is used for turn roughing operations.
72. CW-44930 Beta 2 11-1261 Feature
For the specific Mill-Turn part file, when coordinate system
is selected from the Machine Definition and the Extract
machinable Features command is executed, then
SOLIDWORKS crashes.
73. CW-44920 PR2 11-1237 UI
The Error message indicating potential tool collision
toolpath gouging needs to be updated to indicate which
parameters/settings are invoking this message.
74. CW-44914 Beta 1 11-1216 OperationIn the tool database of thread mill conditions, duplicatethread conditions are observed. This is seen when the user
tries to add a thread condition to the hole feature.
75. CW-44861 Beta 2 11-1174 Feature
In turning, when full rebuild is done, then the join
segments added by the user after modifying a feature
which was recognized earlier by Automatic Feature
Recognition are lost. After rebuild, the user defined join
segments are deleted and the earlier deleted segments of
the feature are added again.
76. CW-44726 PR2 11-1039 TechDB
Thread Mill Condition definitions for spindle type set to
"Sub spindle "within TechDB need to be updated and thethread type set for the Imperial threads in the Metric
database is incorrect and needs to be corrected.
77. CW-44661 SP0 11-0923 FeaturesFor the specific Mill part, toolpaths cannot be generated
for the Part PerimeterBoss feature.
78. CW-44586 Beta 2 11-0986 Post Help
In the Help documentation for Universal Post Generator, it
should be mentioned that the variable OPR_Z_DEPTH is
available only for Drilling cycles and not for Milling cycles.
79. CW-43454 Beta 1 11-0650 Operation
For a Multiaxis operation, if user sets the Rotate Toolpath
option to xinstances in the Advanced tab of operationParameters dialog box, then user is unable to revert and
turn it off so as to get only one instance of the toolpath.
80. CW-43390 PR2 11-0580 Toolpath
The corner machining option under the side parameters of
a contour mill operation to machine the corners of
features is not working in CAMWorks 2014.
-
8/9/2019 Cw 2015 Build Info
10/13
10 | P a g e
Sr.
No.
CPR
NumberCAMWorks
2015 VersionHelp
Desk IDArea Description
81. CW-42854 PR1 10-9349 UI
Whenever a multi surface feature or a turn feature is
inserted by the user, then the user will not get any
information regarding the successful insertion of the
feature. Display a bubble message after the successful
insertion of the feature, when the insert multi surfacefeature wizard and turn feature wizard are in pinned state.
82. CW-42837 Beta 2 11-0455 Operation
In CAMWorks 2014 SP1 version, in the operation
parameters whenever a tool station number is changed to
an already used tool station number, then the comments
of the tool get overwritten with the comments of another
tool.
83. CW-42641 Beta 1 11-0362 Toolpath
When ignore air segments option is selected for contour
mill operations for slot features and if the avoid area
options are set to "Feed Around" or "Rapid Over", the tool
path gets corrupted.
84. CW-42481 Beta 1 11-0293 Toolpath
For the specific Mill part, when the Pattern type for the
Area Clearance toolpath is set to VoluMill, the resultant
toolpath does not machine most of the large areas.
85. CW-42477 SP0 11-0267 TechDBThe 'Edge Margin' parameter for the Multiaxis Mill
operation should be made available in TechDB.
86. CW-42455 Beta 2 11-0278 System
Provide an ability to define a description for every strategy
in TechDB and in CAMWorks UI. The description should be
user defined in TechDB and for reference purpose in
CAMWorks under the feature parameters dialog box.
87. CW-42250 PR2 11-0179 Assembly
The Mill Part Setup allow the user to define the X axis
direction using an alternate co-ordinate system apart from
the one used to define the Fixture Co-ordinate System on
the machine node.
88. CW-42215 Beta 1 11-0027 Toolpath
In the specific part when a pocket feature is machined
using rough mill operation with 'Stay at Depth' option set
to On, the resultant toolpath leaves wedges.
89. CW-41366 Beta 1 10-9788 Operation
For the specific Mill part, when user tries to machine the
Corner slot feature after replacing the default tool
assigned with the tool of larger diameter, CAMWorks
crashes.
90. CW-41142 Beta 1 10-9683 Feature
For the specific Mill part, when user tries to interactively
insert irregular pocket features using face entities, then
the feature cannot be inserted. The same feature gets
inserted if a sketch is used to define the base entity.
-
8/9/2019 Cw 2015 Build Info
11/13
11 | P a g e
Sr.
No.
CPR
NumberCAMWorks
2015 VersionHelp
Desk IDArea Description
91. CW-41062 SP0 10-9624 Feature
For the specific Mill part, the Roughing and contour Mill
toolpaths generated for Irregular slot features recognized
using AFR end up gouging the part.
92. CW-40815 Beta 1 ---- Turn
In turning when a part is machined using two spindles and
with sub spindle operations then, in step through display,
the sub spindle appears to be moving to home position
after grabbing the part. The correct way is that the main
spindle should return to home position and not the sub
spindle.
93.CW-40544
CW-35284Beta 1
10-9413
10-6824Toolpath
For the specific Mill part, when the Pattern type for the
Area Clearance toolpath is set to VoluMill, the resultant
toolpath gouges the part.
94. CW-40447 Beta 1 10-9028 Rebuild
The feature length for threading operations in turning
doesnt update as per the changes done in the part. The
user will have to manually change the value.
95. CW-40406 Beta 2 10-9335 Features
For the specific Turn part, on executing the Extract
Machinable Features command, the resultant OD Feature
ignores some of the line and arc segments of the part.
96. CW-40344 Beta 2 10-9303 Features
For the specific Mill Part file, Contour Mill toolpaths are
not generated for pocket feature defined through
Automatic Feature Recognition or Interactive Feature
Recognition.
97. CW-40299 Beta 2 10-9264 Features
Simplify the automatic recognition of features which have
intersecting hole features. The user should get the hole
feature separately along with a slot or pocket feature.
98. CW-40115 SP0 10-9203 Features
When 'Extract Machinable Features' is done in assembly,
then the hole thread call outs for features having threads
are not recognized. Instead the hole feature with thread is
recognized as a simple hole feature.
99. CW-39974 Beta 1 10-9145 UI
Whenever an invalid character is entered in the first cut
amount field of rough mill and contour mill operations,CAMWorks displays the error message for 30 times. It
should be displayed only once and shouldnt repeat after
the user closes the error message dialog box.
-
8/9/2019 Cw 2015 Build Info
12/13
12 | P a g e
Sr.
No.
CPR
NumberCAMWorks
2015 VersionHelp
Desk IDArea Description
100. CW-39783 Beta 1 10-9050 Rebuild
CAMWorks is not acknowledging model changes for all
CAMWorks configurations. Only the active Configuration is
Rebuilt. No prompt for Rebuilding is displayed for the
other Configurations.
101. CW-39689 SP0 10-9624 Rebuild
For Mill parts, the toolpath for one of the feature instances
within a group feature is not deleted when its feature is
deleted and the part is Rebuilt.
102. CW-39621 Beta 2 10-8955 Toolpath
For the specific Mill part, VoluMill toolpath generated for
the slot feature does not consider the circular islands
which were recognized automatically or interactively.
103. CW-39431 Beta 1 10-8862 TechDB
When user interactively insert a Multi Surface Feature and
sets the strategy to either Area Clearance and ConstantStepover or Constant Stepover, for the resultant
Constant Stepover operation generated, the Offset Curve
strategy in the Pass Options section of the Constant
Stepover tab doesnt match with the corresponding entry
in TechDB.
104. CW-39156 Beta 1 10-8734 ToolpathWhen rough milling is done using the VoluMill pattern, the
islands in the feature get ignored.
105. CW-38791 Beta 1 ---- Toolpath
For the specific mill Part, when VoluMill pattern is applied,
the resultant Rough Mill toolpath ignores the large bossfeature at the center and machines through it.
106. CW-38583 Beta 2 10-8548 TechDB
In CAMWorks 2013, two new material types HP Drilland
U DRILL were added to the TechDB but were arent
added to the Feeds/Speed Library. Consequently, the Feed
and Speed values for these material type is zero. To avoid
this error, these materials should be removed from
TechDB.
107. CW-38400 Beta 1 10-8440 Operation
For the specific part with Irregular Pocket Feature, when
user executes the Save Operation Plan command and saves
it as a New Feature Condition, CAMWorks crashes.
108. CW-36694 Beta 1 --- ToolpathFor the specific part, the rough mill toolpath with pattern
type set to VoluMill results in a gouge.
109. CW-36531 Beta 1 10-7493 Toolpath
For the specific part, the Roughing toolpath for the
Perimeter-Open Pocket feature doesnt get generated
when the pattern Type is set to VoluMill.
-
8/9/2019 Cw 2015 Build Info
13/13
13 | P a g e
Sr.
No.
CPR
NumberCAMWorks
2015 VersionHelp
Desk IDArea Description
110. CW-36478 PR1 ---- Toolpath
In Mill features having islands with height more than the
feature the rough mill toolpath with pattern type set to
VoluMill gouges the feature.
111. CW-32574 Beta 1 10-5846 Toolpath
In the specific part for a perimeter feature of the type
open pocket, rough mill toolpath with pattern set to
VoluMill cannot be generated.
112. CW-31949 Beta 1 10-5408 Toolpath
In Mill assembly mode, when user selects VoluMill as the
Pattern type, the resultant toolpaths do not take into
account the fixtures to be avoided.
113. CW-31692 PR1 10-5204 Toolpath
In mill features if the islands have one or more edges
collinear with the feature edge, then the rough mill
toolpath generated with pattern type set to Volumill
gouges the feature by ignoring the islands.
114. CW-26033 Beta 1 10-1331 Toolpath
When rough mill toolpath is generated with pattern type
set to VoluMill for an open pocket feature having islands
with multiple steps then, the island geometry is not
considered correctly and the resultant toolpath gouges the
islands.