Mehboob Ahmad KhanElectrical Engineer (Operation and maintenance) at Al Yamama Group –Riyadh, Saudi Arabia

Nationality: Pakistani Cell No. KSA-00966-530581269Email: mehk25@hotmail.com , Skype ID: mehboob158

••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

Short Description:

Target Objective: Desire the Challenging Position of Electrical Engineer and seek environment, where my skills and loyalty will be

rewarded with career advancement and guidance.

Experience: Three Year Plus (2.5 Year KSA + One Year Pakistan)

Current Job Title: Generator Plant Engineer ( 4200 KVA)

Education: B.Sc. Electrical Engineering (Graduation , 2008-2012).

University Name: Bahauddin Zakariya University Multan-Pakistan.Driving License: Valid driving license- KSAMarital Status: Married

Number of Dependents: one

Career Level: Mid career

Membership:I. Saudi Council of Engineering

II. Pakistan Engineering Council

Qualitative Work Experience Description:-

Country of Work: Saudi Arabia. Employer : Al Yamama Company Project: Princess Nora Bint Abdul Rehman University Riyadh, Saudi Arabia Consultant/Main contractor: Dar Al-Handasah Employment Tenure: Jan 2012- Present

Position Held: I. Generator Plant Engineer ( May,2014 to Present )II. Low Voltage Engineer ( Feb,2013 to April,2014)

OVERVIEW OF RESPONSIBILITIES:

I. Generator Plant Engineer ( May,2014 to Present ): Generator Plant CAT-3616*8 (4200 KVA , 13.8KV)

As Generator Plant Engineer have a following responsibilities:

Supervision and managing a staff working under me. Troubleshooting, Preventive & Corrective maintenance of 13.8 KV Power Plant. Troubleshooting of control signals from Generator to Switchgear and then to SCADA. Starting motor troubleshooting. Weekly run test report of Generators to the consultant and Head of the Department. Emergency operation of Generator during failure of SEC supply. Troubleshooting of engine problems. Maintenance of Neutral Grounding Resistance ( NGR). Sensors problems i.e. Temprature sensor and pressure sensor. Testing and maintenance of Batteries and Battery charger. Synchronizing Panel maintenance and troubleshooting. PLC troubleshooting and maintenance. Air Compressor maintenance.

II. Low Voltage Engineer ( Feb,2013 to April,2014)

Working as Low voltage Central Maintenance Engineer handling the following Utility Areas:-

1. Generator Plant.2. Chiller Plant.3. Boiler Plant.4. Pump Station.5. RO Plant.6. Data Center.7. Utility Tunnel.8. Sewage Treatment Plant (STP).9. Fountain System.

As a Electrical Engineer, I am performing following types of Responsibilities at Princess Noura University Project:-

a. Corrective Maintenance (CM): Diagnosing and troubleshooting of power system of MDB’s , MCC’s , DP’s & small/lighting Panels. Diagnosing and Troubleshooting of control signals of MDB’s , MCC’s , DP’s & small/lighting Panels to DDC

for BMS. Troubleshooting of Duplex Submersible Pump system and signal from sump pump to DDC for BMS. Analyzing and Troubleshooting of VFD’s and Soft starter and there communication to DDC for BMS. Looking and troubleshooting for Fountain system. Troubleshooting of automated Gate Barriers & Auto roll up shutter door.

b. Planned Preventive Maintenance (PPM). Preparation/implementation of Master Plan for PPM of all Electrical assets in PNU utility area. Framing a PPM frequency as per manufacturer recommendation for all assets mention in master plan. Formulating of Preventive maintenance instructions ( PMI) for individual category of assets as per manual

description. Accomplishing all demand of consultant like amendment in Master Plan , Making asset category vs asset

PMI chart , asset category vs asset quantity chart etc. Feeding of PPM Master Plan/job plan/PMI frequency on Maximo for automated work order generation. Proficient for performing of all PMI for the Electrical assets. Satisfying to consultant for on time/proper implementation of submitted Job plan.

c. Miscellaneous work: Protection (lsig) and Contact Resistance testing of ACB. Infrared testing. IR testing of motor. Hipot testing. Earth pit testing. LV cable jointing upto 300 sq mm. Well versed with use of underground Power cable fault locator. Well versed with use of cable route Locator.

Along with above mentions, have a overview of the following systems also: SCADA controlled ABB Distributor’s for the ring main Unit (RMU). SCADA controlled ABB Switchgear. ABB Package Substation. ABB Transformer. BMS monitored SOCOMEC & Chloride make UPS.

Country of Work: Pakistan

Employer: Preston University . Duration: May-2012 to Feb-2013 Project: Preston University Islamabad Campus.Position Held: Lecturer at B.Tech Department. Major Responsibilities: Worked as a Lecturer (B.Tech Department) delivering the following Concepts:-

Alternator working principle, E.M.F equation of Alternator. Induction Motor working principle, comparison of motor and generator action. Working principle of transformer, core type transformer, shell type transformer, E.M.F equation of

transformer, open circuit test and short circuit test.

Faraday ‘law of electromagnetic induction, lens’s law. Concept of electric potential, Law of resistance, conductance and conductivity, effect of temperature on

resistance . Ohm’s law, voltage divider rule and division of current in parallel circuit. Joul’s law of electric heating. Concept of Capacitor and capacitance, energy stored in capacitor. Permeability of the medium, Law of magnetic force, magnetic field intensity (H) and Magnetic flux

density(B).

Training Course:

1. Two week PLC & HMI training on Siemens hardware and software ( practiced on S7-300 by using Simatic manager and Simatic Wincc Flexible) held by Electrical solution international Pvt ltd at Bahria university Islamabad- Pakistan.

2. Three days BMS field based training held by Johnson Control Inc (JCI-KSA) .3. One week Maximo training held by IT department of Al Yamama Company ( AYC-KSA).4. One day ( Three Hrs) User and Operator Training on CHLORIDE UPS BY Saudi Electronic Trading Company

(SETRA)5. One day ( Three Hrs) training on Operation & Maintenance best Practices on Low Voltage Equipment by

PARSONS.6. Two day ( Six Hrs) training on Generator System Operation & Maintenance best Practices by PARSONS.

Communication Skills:

I. English II. Urdu III. Arabic

Computer Skills:

I. MS Office II. Auto CAD III. HTML IV. Maximo V. Sematic Manager VI. Internet Surfing.