CUSTOM TIE-DOWN BRACKETS FOR VICTORY 938 · Use only good quality RATCHET-type tie-down straps to...
3
THANK YOU FOR CHOOSING KϋRYAKYN! PROTECT YOURSELF AND OTHERS FROM POSSIBLE INJURY AND/OR PROPERTY DAMAGE OR LOSS. PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS, AND NOTICES REGARDING THE INSTALLATION, USE, AND CARE OF THIS PRODUCT. MAKE SURE THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT: 1 Left Tie-Down Bracket for Victory 1 Right Tie-Down Bracket for Victory 1 Hardware Kit Containing: 4 Spacers 4 Washers 4 Split Lock Washers 4 M10-1.5 X 60MM Bolts 1 Installation Instructions TOOLS SUGGESTED Socket set and ratchet, Open end wrench set, Torque wrench (ft. lbs.) STEP 1 Read and understand all steps in the instructions before starting the installation. Park the motorcycle on a hard, level surface and turn off the ignition. Allow the engine and exhaust system to cool. STEP 2 Protect the front fender with a service cover or soft, clean towel. INSTALLATION CUSTOMER SERVICE 877.370.3604 (toll free) INSTALLATION QUESTIONS [email protected] or call 715.247.2983 LIMITED WARRANTY Küryakyn warrants that any Küryakyn products sold hereunder, shall be free of defects in materials and workmanship for a period of one (1) year from the date of purchase by the consumer excepting the following provisions: ● Küryakyn shall have no obligation in the event the customer is unable to provide a receipt showing the date the customer purchased the product(s). ●The product must be properly installed, maintained and operated under normal conditions. ●Küryakyn makes no warranty, expressed or implied, with respect to any gold plated products. ●Küryakyn shall not be liable for any consequential and incidental damages, including labor and paint, resulting from failure of a Küryakyn product, failure to deliver, delay in delivery, delivery in nonconforming condition, or for any breech of contract or duty between Küryakyn and a customer. ●Küryakyn products are often intended for use in specific applications. Küryakyn makes no warranty if a Küryakyn product is used in applications other than intended. ●Küryakyn electrical products are warranted for one (1) year from the date of purchase by the consumer. L.E.D.’S contained in components of Küryakyn products will be warranted for defects in materials and workmanship for 3 years from the date of purchase where as all other components shall be warranted for one(1) year. This includes, but is not limited to; control modules, wiring, chrome & other components. ●Küryakyn makes no warranty of any kind in regard to other manufacturer¹s products distributed by Küryakyn. Küryakyn will pass on all warranties made by the manufacturer and where possible, will expedite the claim on behalf of the customer, but ultimately, responsibility for disposition of the warranty claim lies with the manufacturer. ABOUT OUR CATALOG For purchasing Küryakyn® products, you can receive a complete catalog free of charge. Send the Proof-of-Purchase below with your address to: Küryakyn, P.O. Box 339, Somerset, WI 54025. Please indicate either Accessories Catalog for Harley-Davidson® or GL & Metric Cruisers. Be sure to ask your local dealer about other Küryakyn® products, the motorcycle parts and accessories designed for riders by riders. ©2005 Küryakyn USA® All Rights reserved. CUSTOM TIE-DOWN BRACKETS FOR VICTORY 938-21MC-0913 -cont.- THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY. This indication alerts you to the fact that ignoring the contents described herein may negatively affect product performance and functionality or damage the product itself or the product to which it is being attached. This indication alerts you to the fact that ignoring the contents described herein can result in minor or moderate potential injury. 938 NOTE: In the following instructions, left and right may be referred to as “clutch-side” (left) and “brake-side” (right) for clarity. Working around the sharp edges of the cylinder- head fins exposes your hands to injury. Wear pro- tective gloves to prevent serious injury. YOU WILL BE WORKING AROUND THE ENGINE AND EXHAUST SYSTEM DURING INSTALLATION. ENSURE THAT THE ENGINE AND EXHAUST SYSTEM HAVE FULLY COOLED TO PREVENT INJURY.
Transcript of CUSTOM TIE-DOWN BRACKETS FOR VICTORY 938 · Use only good quality RATCHET-type tie-down straps to...
THANK YOU FOR CHOOSING KϋRYAKYN! PROTECT YOURSELF AND OTHERS FROM POSSIBLE INJURY AND/OR PROPERTY DAMAGE OR LOSS. PAY CLOSE ATTENTION TO ALL INSTRUCTIONS, WARNINGS, CAUTIONS, AND NOTICES REGARDING THE INSTALLATION, USE, AND CARE OF THIS PRODUCT.
MAKE SURE THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT: 1 Left Tie-Down Bracket for Victory 1 Right Tie-Down Bracket for Victory 1 Hardware Kit Containing: 4 Spacers 4 Washers 4 Split Lock Washers 4 M10-1.5 X 60MM Bolts 1 Installation Instructions TOOLS SUGGESTED Socket set and ratchet, Open end wrench set, Torque wrench (ft. lbs.)
STEP 1 Read and understand all steps in the instructions before starting the installation.
Park the motorcycle on a hard, level surface and turn off the ignition. Allow the engine and exhaust system to cool.
STEP 2 Protect the front fender with a service cover or soft, clean towel.
INSTALLATION
CUSTOMER SERVICE 877.370.3604 (toll free)
INSTALLATION QUESTIONS
[email protected] or call 715.247.2983
LIMITED WARRANTY
Küryakyn warrants that any Küryakyn products sold hereunder, shall be free of defects in
materials and workmanship for a period of one (1) year from the date of purchase by the
consumer excepting the following provisions:
● Küryakyn shall have no obligation in the event the customer is unable to provide a receipt
showing the date the customer purchased the product(s).
●The product must be properly installed,
maintained and operated under normal conditions.
●Küryakyn makes no warranty, expressed or
implied, with respect to any gold plated products.
●Küryakyn shall not be liable for any
consequential and incidental damages, including labor and paint, resulting from failure of a
Küryakyn product, failure to deliver, delay in delivery, delivery in nonconforming condition, or
for any breech of contract or duty between Küryakyn and a customer.
●Küryakyn products are often intended for use in
specific applications. Küryakyn makes no warranty if a Küryakyn product is used in
applications other than intended.
●Küryakyn electrical products are warranted for one (1) year from the date of purchase by the
consumer. L.E.D.’S contained in components of Küryakyn products will be warranted for defects in materials and workmanship for 3 years from
the date of purchase where as all other components shall be warranted for one(1) year.
This includes, but is not limited to; control modules, wiring, chrome & other components.
●Küryakyn makes no warranty of any kind in
regard to other manufacturer¹s products distributed by Küryakyn. Küryakyn will pass on
all warranties made by the manufacturer and where possible, will expedite the claim on behalf of the customer, but ultimately, responsibility for disposition of the warranty claim lies
with the manufacturer.
ABOUT OUR CATALOG For purchasing Küryakyn® products, you
can receive a complete catalog free of charge. Send the Proof-of-Purchase below with
your address to: Küryakyn, P.O. Box 339, Somerset, WI 54025.
Please indicate either Accessories Catalog for Harley-Davidson® or GL & Metric Cruisers.
Be sure to ask your local dealer about other
Küryakyn® products, the motorcycle parts and accessories designed for riders by riders.
©2005 Küryakyn USA® All Rights
reserved.
CUSTOM TIE-DOWN BRACKETS FOR VICTORY
938-21MC-0913
-cont.-
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
This indication alerts you to the fact that ignoring the contents described herein may negatively affect product performance and functionality or damage the product itself or the product to which it is being attached.
This indication alerts you to the fact that ignoring the contents described herein can result in minor or moderate potential injury.
938
NOTE: In the following instructions, left and right may be referred to as “clutch-side” (left) and “brake-side” (right) for clarity.
Working around the sharp edges of the cylinder-head fins exposes your hands to injury. Wear pro-tective gloves to prevent serious injury.
YOU WILL BE WORKING AROUND THE ENGINE AND EXHAUST SYSTEM DURING INSTALLATION. ENSURE THAT THE ENGINE AND EXHAUST SYSTEM HAVE FULLY COOLED TO PREVENT INJURY.
PAGE
2
TUBULAR-STYLE ENGINE GUARD INSTALLATION: STEP 3 Determine clutch-side (left) and brake-
side (right) Tie-Down Brackets. PIC 1 STEP 4 Starting on the clutch-side, gently pull
the rubber boot (PIC 2) away from the engine guard mount.
STEP 5 Remove the two OEM bolts shown in PIC 2. STEP 6 Slide the clutch-side (left) Tie-Down Bracket in between the engine
guard weldment and the frame. PIC 3 STEP 7 Insert the included M10 Bolts through the Split Lock Washers,
Washers, engine guard weldment, Tie-Down Bracket and into the frame.
STEP 8 Thread both Bolts into the frame and torque the Bolts to 52
FT/LBS. Slide the rubber boot back over the mount. STEP 9 Repeat STEPS 4 through 8 for the brake-side (right).
FORGED-STYLE ENGINE GUARD INSTALLATION: STEP 10 Determine the left Tie Down Bracket from the right. PIC 1 STEP 11 Locate and remove the two OEM bolts in the clutch-side (left)
forged engine guard. PIC 4. STEP 12 Locate the engine
guard’s lower mount-ing bolt. PIC 5 Loosen the bolt. DO NOT FULLY RE-MOVE THE BOLT. Loosening the bolt will make aligning the upper bolt holes
easier.
-cont.-
CUSTOM TIE-DOWN BRACKETS FOR VICTORY INSTALLATION
PIC 2
REMOVE THE TWO OEM BOLTS
SLIDE RUBBER BOOT AWAY FROM MOUNT
CLUTCH-SIDE (LEFT)
CLUTCH-SIDE (LEFT) PIC 3
SLIDE TIE-DOWN BEHIND THE ENGINE GUARD WELDMENT AS SHOWN
INSERT TWO INCLUDED BOLTS WITH THE HARD-WARE. TORQUE TO 52 FT/LBS
REMOVE THE TWO OEM BOLTS
CLUTCH-SIDE (LEFT) PIC 4
PIC 5
LOOSEN THE LOWER BOLT
CLUTCH-SIDE (LEFT)
PIC 1
BRAKE-SIDE (RIGHT) CLUTCH-SIDE (LEFT)
FRONT OF BIKE FRONT OF BIKE
PAGE
3
STEP 13 Insert the included M10 Bolts through the Split Lock Washers, Washers, and Left Tie-Down Bracket. Place the included Spacers over the threaded ends of the bolts. PIC 6
STEP 14 Thread the front bolt into the front hole in the frame. Leave the bolt loose for now. STEP 15 Thread the rear bolt into the rear hole in the frame.
TIP: Use an open end wrench to start the rear bolt. STEP 16 Fully tighten both bolts and torque them to 52 FT/LBS. STEP 17 Torque the lower mounting bolt (from STEP 12) to 52 FT/LBS. STEP 18 Repeat STEPS 11 through 17 for the brake-side (right).
Ride On!
If installing this product for another party, please make sure they receive this copy of the installation instructions so they are aware of the important information contained in them.
It is the end user’s responsibility to ensure that all of the fasteners (including pre-assembled) are tightened before operation of the motorcy-cle. Küryakyn will not provide warranty coverage on products or compo-nents lost due to improper installation or lack of maintenance. Periodic in-spection and maintenance are required on all fasteners.
Use only good quality RATCHET-type tie-down straps to secure you motor-cycle. Ensure the straps have a weight rating sufficient to support your motorcycle. DO NOT USE straps that have tears, worn seams, cuts, abrasions, bent hooks, faulty ratchets, or unknown weight ratings to secure a motorcycle. Use only good quality wheel chocks designed for your type of motorcycle. Follow wheel chock manufacturer’s recommendations for securing your motorcycle to the trailer or motorcycle lift. Condor brand wheel chocks (Kuryakyn Part Number 920 or 922) are sold separately through Kuryakyn.com or your Kuryakyn dealer.
CUSTOM TIE-DOWN BRACKETS FOR VICTORY INSTALLATION
CLUTCH-SIDE (LEFT)
PIC 6
FRONT OF BIKE
CLUTCH-SIDE (LEFT)
PIC 7
USE A COMBINA-TION WRENCH TO START THIS BOLT
FRONT OF BIKE
