CTS® Drilled Shaft Reinforcement - Con-Tech Systems · any of your project needs. ... page 2...

11
CTS® Drilled Shaft Reinforcement

Transcript of CTS® Drilled Shaft Reinforcement - Con-Tech Systems · any of your project needs. ... page 2...

Page 1: CTS® Drilled Shaft Reinforcement - Con-Tech Systems · any of your project needs. ... page 2 Contents: Company Introducion: Cover ... 2. Utilization of a CTS®/IBO® Hollow Bar as

CTS® Drilled Shaft Reinforcement

Page 2: CTS® Drilled Shaft Reinforcement - Con-Tech Systems · any of your project needs. ... page 2 Contents: Company Introducion: Cover ... 2. Utilization of a CTS®/IBO® Hollow Bar as

Con-Tech Systems® was founded in 1985 and is a family owned

company. Since inception not only have we remained close to our roots with our innovative Strand and Bar products, but we have also developed and promoted many other unique and in-

novative products, including the ability to produce anchors with standard corrosion protection systems, as well as products with special corrosion protection requirements, to allow our custom-

ers to complete a variety of many difficult projects.

With this wide selection of products still available to our cus-

tomers today we are able to service not only large international contractors but also small owner operators.

Through our several production plants and offices located across Canada and the USA; from British Columbia to Ontario, from Washington State to North Carolina, we are able to service any of your project needs.

... page 2

Contents:

Company Introduction:

Cover

Company Profile.......................................... Page 2Drilled Shaft Intro, HRTB™ Advantages.......... Page 3Our Commitment........................................ Page 4Grade 60,80,100 Cage Detail Comparisons Page 5CTS® HRTB™ Tech Data................................... Page 6/7CTS® Hollow Bar Tech Data........................... Page 6/7Grade 80 Hex Nut, Lock Nut Tech Data....... Page 8Grade 80 Coupler Tech Data and Notes...... Page 9 Grade 100 Hex Nut, Lock Nut Tech Data..... Page 10Grade 100 Coupler Tech Data..................... Page 11Back Cover: Contact Information

CTS® Drilled Shaft Reinforcement

Page 3: CTS® Drilled Shaft Reinforcement - Con-Tech Systems · any of your project needs. ... page 2 Contents: Company Introducion: Cover ... 2. Utilization of a CTS®/IBO® Hollow Bar as

... page 3

CTS® Drilled Shaft Reinforcement

CTS® Hot Rolled Thread Bars: Your SOLID Solution

Advantages of CTS® Hot Rolled Thread Bar:

Our CTS® Hot Rolled Thread Bars (HRTB™) are available in various grades. They are fully threaded along the entire length with a hot formed thread. The CTS® Hot Rolled Thread Bars are in compliance with ASTM A615 depending on their design requirements.

CTS® Drilled Shaft Reinforcement - Introduction:

• The combination of high strength steel and high strength concrete is cre-

ating new opportunities for engineers plus cost savings for Contractors.• The use of Grade 80ksi and Grade100ksi HRTB™ vs. Grade 60 rebar rein-

forcement with lap splices, reduces congestion and weight significantly.• The drilled shafts with HRTB™ can be prefabricated offsite in modules, us-

ing steel plates and couplers for fast and easy installation on the job site.• The HRTB™ thread is a course and continuous thread throughout the bar.

Compared to fine machined thread ends of rebar, it is much less sensi-tive for any damages; “damage proofed”.

• The couplers can be preinstalled on the end of the bars and they are designed and manufactured to develop 125% of the yield strength of the bars after ASTM A615.

#32, Grade 80, 4” HRTB™.

The largest diameter HRTB™ available.

The CTS®, Grades 80 and 100, Hot Rolled Thread Bars are one of the strongest, simplest, most robust and cost effec-

tive bars in the industry. The ductility (elongation) is equal or better than that required for Grade 60 bars, as per ASTM A615.

The continuous hot rolled thread along the entire length of the bar allows the bars to be cut, spliced and anchored with couplers or nuts at any point along the bar.

US DOMESTIC Hot Rolled Thread Bar.

The two flat sides on the Hot Rolled Thread Bar eliminate jamming of nuts or couplers. The thread is self cleaning.

Available in up to 4” diameter. The largest available on the current market.

Page 4: CTS® Drilled Shaft Reinforcement - Con-Tech Systems · any of your project needs. ... page 2 Contents: Company Introducion: Cover ... 2. Utilization of a CTS®/IBO® Hollow Bar as

... page 4

CTS® Drilled Shaft Reinforcement

Our Commitment:

Con-Tech Systems® is committed to providing our customers with the best quality products and service. We take pride in our strict production process which ensures full customer satisfaction from the moment an order is placed.

CTS®

Drilled Shaft

Reinforcement

Spacer Plates for safer lifting

Grade 80 HRTB™ and

Hollow Rebar for CSL or TIP

Fast splicing

NEW Cage Design PREVIOUS Cage Design

Page 5: CTS® Drilled Shaft Reinforcement - Con-Tech Systems · any of your project needs. ... page 2 Contents: Company Introducion: Cover ... 2. Utilization of a CTS®/IBO® Hollow Bar as

CTS® Drilled Shaft Reinforcement

... page 5

Grade 60, 80, 100 Cage Detail Comparisons:

Typical Section View

* All of the above shown sections are designed for the same load.

Typical Sections of a 6’ Diameter Drilled Shaft

Grade 60

Weight of vertical bar in cage at 50’ length:

31,280 lbs

(46) #18 Grade 60 Bars

Grade 80 (20) #24 Grade 80 Bars

Weight of vertical bar in cage at 50’ length:

23,270 lbs

Grade 100 (16) #24 Grade 100 Bars

Weight of vertical bar in cage at 50’ length:

18,616 lbs

Page 6: CTS® Drilled Shaft Reinforcement - Con-Tech Systems · any of your project needs. ... page 2 Contents: Company Introducion: Cover ... 2. Utilization of a CTS®/IBO® Hollow Bar as

... page 6

CTS® Hot Rolled Thread Bar Technical Data:CTS® Drilled Shaft Reinforcement CTS® Drilled Shaft Reinforcement

974 4331 1278 5684 828 3-1/2" 90 3.880 98.60 9.61 6200 32.70 48.65 769 3420 1009 4488 832 4" 100 4.290 109.00 61.60

91011141820

1-1/8"1-1/4"1-3/8"1-3/4"2-1/4"2-1/2"

1.4131.5871.8862.4652.7173.209

283236435763.5

452553

590690101918602230 8

Elongation

%

Max Jacking Load(80% of Ultimate)kips kNlbs./ft

Max Design Load(60% of Ultimate)

Weight Ultimate Strength

Ultimate Strength

3.01

Elongation

0.44sq.in

0.60

lbs./ft1.602.042.603.25

6.408.0011.3820.2424.65

2.23

12.17 7852 41.40

#678

in3/4"7/8"1"

19mm

2225

Size Nominal Diameter Area Weight Yield Load

1.562.254.004.91

mm22843875106458191006145225813168

4.255.377.6513.6016.71

kg/m

3.043.975.06

102125180320393

kips35486380

kN

213280355

133163236420

kips466383105

kN200280359467

8888

%9998

Nominal Diameter

in1"

1-1/4"1-3/8"1-3/4"2-1/4"2-1/2"3"

mm26

75

Area

sq.in mm20.851.251.582.694.005.166.85

5488061019

32364657

17352581

2.075 52.702.465

kips kN127188237

4.486.548.28

65

14.1020.9527.10

36.301.626 41.30

102150190

777

4572

kips kN76113142

339502632

5658361054

0.760.951.10

242360464617

18.2024.12

480620822

6007741028

179226683442

403 322480

721347

35.90

4.39

6.85

9.4714.08

4536678451435213527573656

102150190323

kg/m

Yield Load

kips kN

5.56

Size Nominal Diameter Area Weight Yield Load Ultimate Strength Elongation#7

sq.in0.597/8"

mm22

mm23800.953 24.20

in

1"1-1/8"1-1/4"1-3/8"1-3/4"2-1/4"2-1/2"

35435763.5

252830

1.492.254.004.91

9621452258131674418

491616707

5.077.6514.0816.6823.27

lbs./ft2.002.593.253.73

7.5511.3820.9524.8634.68

kg/m2.983.854.835.55

149225400491685

kips597695110

645973174021222960

kN255329413474

173261467570795

kips6888111127

7701162207725343535

kN304393493565

88866

%8888

27543658

4526698431434 1075

160120652743

22.4024.9028.1031.4035.90

2429 719 3090 8

40.3047.9062.6069.0081.50

79814201748 515

156

0.791.001.27

182024

69.003.209 81.50

mm

Maximum OD

753"

Grade 80 (Left Hand Thread) ASTM A615/18

Grade 100 (Right Hand Thread) ASTM A615/18

Grade 150 (Right Hand Thread) ASTM A722

1.200 30.50

6.85 4418 23.27 34.68 54824 3" 75

Maximum OD

Maximum OD

in

in mm

in mm0.8820.9801.1061.236

891011

kips kN kips kN

1.083 27.501.228 31.201.319 33.501.543 39.20

14

62.60

1.886 47.902.472 62.802.717

1.429

%

2.811 71.403.209 81.50

619822

33314418

Grade 160 (Right Hand Thread) Nominal Diameter Area Weight Yield Load Ultimate Strength Elongationin mm sq.in mm2 lbs./ft kg/m

77

345 33/4" 20 0.49 314 1.72 2.56 64 283 785/8" 315 0.27 177 0.97 1.44 35 159 43 195

... page 7

For the most current technical information please go to our website: www.contechsystems.com

CTS® Hollow Bar Technical Data:

KEY FEATURES:

1. Used as access tubes for CSL and TIP testing; as well as replacement of solid bars.2. Utilization of a CTS®/IBO® Hollow Bar as the reinforcing Bar. From the static point of view, a

hollow bar is superior to a solid rod of the same cross sectional area with respect to bending moment, shear resistance and surface bond/friction.

3. The CTS®/IBO® Hollow Bar is manufactured from high yield micro alloy, high quality structural steel. This steel is not affected by hydrogen embrittlement or by stress crack corrosion. It has at least the mechanical properties and chemical compositions of ASTM A-706.

4. The threads on the CTS®/IBO® Hollow Bar are formed much like the ribs on a reinforcing bar fabricated according to ASTM-A-706. The deep threads result in 2.4 times higher bond friction compared to standard drill steel rope-threads.

5. Continuous threads guarantee that the CTS®/IBO® Hollow Bar can be cut or coupled anywhere Along its length. A thread pitch of 6 degrees eliminates the need for locking nuts at each coupling.

6. Certified to ISO 9001.

Right Hand Thread

INN

ER

ø

d Dø

Left Hand (shown), Sizes 30/16-52/26Right Hand, Sizes 73/53 - 103/78-51

TITAN THREAD

Bar Size Nominal DiameterEffective

Cross-Section

Load Capacity WeightLeft Hand

/ Right Hand

D Ø / INNER Ø Inside Outside Ultimate YieldD Ø G.U.T.S.

mm in in in² kips kips lbs./lf. Threadmm mm mm² kN kN kg/m

30/16 0.62 1.18 0.53 55.1 42.7 1.8 LEFT16 30 340 245 190 2.7

30/11 0.43 1.18 0.64 72.0 58.5 2.2 LEFT11 30 415 320 260 3.3

40/20 0.78 1.57 1.13 121.4 95.6 3.8 LEFT20 40 730 540 425 5.6

40/16 0.62 1.57 1.40 148.4 118.1 4.8 LEFT16 40 900 660 525 7.2

52/26 1.02 2.05 1.94 208.0 164.2 6.7 LEFT26 52 1250 925 730 9.9

73/53 2.08 2.87 2.50 260.8 218.1 8.9 RIGHT53 73 1615 1160 970 13.2

73/45 1.77 2.87 3.50 356.3 285.5 12.0 RIGHT45 73 2260 1585 1270 17.8

103/78 3.07 4.06 4.87 510.3 404.7 17.0 RIGHT78 103 3140 2270 1800 25.3

Please contact us for availability of the following sizes:73/35 1.38 2.87 4.20 419.3 321.5 14.2 RIGHT

35 73 2710 1865 1430 21.273/56 2.20 2.87 2.11 232.7 186.6 7.3 RIGHT

56 73 1360 1035 830 10.8103/43 1.69 4.06 9.34 934.1 763.9 31.8 RIGHT

43 103 6023 4155 3398 47.3103/51 2.00 4.06 8.80 822.8 600.3 30.0 RIGHT

51 103 5680 3660 2670 44.6127/103 4.05 5.00 5.39 521.6 456.4 19.4 RIGHT

103 127 3475 2320 2030 28.9196/130 5.12 7.72 25.11 2315.5 1607.8 85.7 RIGHT

130 196 16200 10300 7152 127.5Note: Subject to change without notice.

Imperial values converted from metric values; July 2010

ONE MORE SIZE? 08/04/2015

Bar Size Nominal DiameterEffective

Cross-Section

Load Capacity WeightLeft Hand

/ Right Hand

D Ø / INNER Ø Inside Outside Ultimate YieldD Ø G.U.T.S.

mm in in in² kips kips lbs./lf. Threadmm mm mm² kN kN kg/m

30/16 0.62 1.18 0.53 55.1 42.7 1.8 LEFT16 30 340 245 190 2.7

30/11 0.43 1.18 0.64 72.0 58.5 2.2 LEFT11 30 415 320 260 3.3

40/20 0.78 1.57 1.13 121.4 95.6 3.8 LEFT20 40 730 540 425 5.6

40/16 0.62 1.57 1.40 148.4 118.1 4.8 LEFT16 40 900 660 525 7.2

52/26 1.02 2.05 1.94 208.0 164.2 6.7 LEFT26 52 1250 925 730 9.9

73/53 2.08 2.87 2.50 260.8 218.1 8.9 RIGHT53 73 1615 1160 970 13.2

73/45 1.77 2.87 3.50 356.3 285.5 12.0 RIGHT45 73 2260 1585 1270 17.8

103/78 3.07 4.06 4.87 510.3 404.7 17.0 RIGHT78 103 3140 2270 1800 25.3

Please contact us for availability of the following sizes:73/35 1.38 2.87 4.20 419.3 321.5 14.2 RIGHT

35 73 2710 1865 1430 21.273/56 2.20 2.87 2.11 232.7 186.6 7.3 RIGHT

56 73 1360 1035 830 10.8103/43 1.69 4.06 9.34 934.1 763.9 31.8 RIGHT

43 103 6023 4155 3398 47.3103/51 2.00 4.06 8.80 822.8 600.3 30.0 RIGHT

51 103 5680 3660 2670 44.6127/103 4.05 5.00 5.39 521.6 456.4 19.4 RIGHT

103 127 3475 2320 2030 28.9196/130 5.12 7.72 25.11 2315.5 1607.8 85.7 RIGHT

130 196 16200 10300 7152 127.5Note: Subject to change without notice.

Imperial values converted from metric values; July 2010

ONE MORE SIZE? 08/04/2015

Bar Size Nominal DiameterEffective

Cross-Section

Load Capacity WeightLeft Hand

/ Right Hand

D Ø / INNER Ø Inside Outside Ultimate YieldD Ø G.U.T.S.

mm in in in² kips kips lbs./lf. Threadmm mm mm² kN kN kg/m

30/16 0.62 1.18 0.53 55.1 42.7 1.8 LEFT16 30 340 245 190 2.7

30/11 0.43 1.18 0.64 72.0 58.5 2.2 LEFT11 30 415 320 260 3.3

40/20 0.78 1.57 1.13 121.4 95.6 3.8 LEFT20 40 730 540 425 5.6

40/16 0.62 1.57 1.40 148.4 118.1 4.8 LEFT16 40 900 660 525 7.2

52/26 1.02 2.05 1.94 208.0 164.2 6.7 LEFT26 52 1250 925 730 9.9

73/53 2.08 2.87 2.50 260.8 218.1 8.9 RIGHT53 73 1615 1160 970 13.2

73/45 1.77 2.87 3.50 356.3 285.5 12.0 RIGHT45 73 2260 1585 1270 17.8

103/78 3.07 4.06 4.87 510.3 404.7 17.0 RIGHT78 103 3140 2270 1800 25.3

Please contact us for availability of the following sizes:73/35 1.38 2.87 4.20 419.3 321.5 14.2 RIGHT

35 73 2710 1865 1430 21.273/56 2.20 2.87 2.11 232.7 186.6 7.3 RIGHT

56 73 1360 1035 830 10.8103/43 1.69 4.06 9.34 934.1 763.9 31.8 RIGHT

43 103 6023 4155 3398 47.3103/51 2.00 4.06 8.80 822.8 600.3 30.0 RIGHT

51 103 5680 3660 2670 44.6127/103 4.05 5.00 5.39 521.6 456.4 19.4 RIGHT

103 127 3475 2320 2030 28.9196/130 5.12 7.72 25.11 2315.5 1607.8 85.7 RIGHT

130 196 16200 10300 7152 127.5Note: Subject to change without notice.

Imperial values converted from metric values; July 2010

ONE MORE SIZE? 08/04/2015

Bars in compliance with ASTM A706 are also available.

Page 7: CTS® Drilled Shaft Reinforcement - Con-Tech Systems · any of your project needs. ... page 2 Contents: Company Introducion: Cover ... 2. Utilization of a CTS®/IBO® Hollow Bar as

... page 8

Accessories: Grade 80 left hand thread

CTS® Drilled Shaft Reinforcement

# inch mm inch mm inch mm lbs. kg6 3/4" 19 1.50 38.1 1.69 43 0.57 0.267 7/8" 22 1.50 38.1 1.77 45 0.65 0.298 1" 25 1.75 44.5 1.97 50 0.79 0.359 1-1/8" 28 2.00 50.8 2.36 60 1.13 0.5010 1-1/4" 32 2.25 57.2 2.56 65 1.80 0.8011 1-3/8" 36 2.50 63.5 2.87 73 2.35 1.0514 1-3/4" 43 3.00 76.2 3.70 94 3.04 1.3818 2-1/4" 57 3.50 90 4.33 110 9.68 4.4020 2-1/2" 63.5 4.00 100 4.53 115 10.80 4.8024 3" 75 4.00 100 5.71 145 11.57 5.2528 3-1/2" 90 5.25 133 6.70 170 24.65 11.1832 4" 100 5.50 140 7.50 191 28.05 12.72

# inch mm inch mm inch mm inch mm lbs. kg6 3/4" 19 1.26 32 1.69 43 1.61 41 0.66 0.307 7/8" 22 1.38 35 1.77 45 1.85 47 0.67 0.318 1" 25 1.61 41 1.97 50 2.09 53 0.79 0.359 1-1/8" 28 1.81 46 2.36 60 2.36 60 0.90 0.4010 1-1/4" 32 2.17 55 2.56 65 2.83 72 1.57 0.7011 1-3/8" 36 2.36 60 2.87 73 3.07 78 2.52 1.12

Anchor Nut

Accessories Grade 80 (left hand thread)

Wrench Size

(F)Size Nominal Diameter

Length

(L)

Weight

Hex Nut

# inch mm inch mm inch mm lbs. kg6 3/4" 19 1.50 38 4.13 105 1.14 0.527 7/8" 22 1.50 38 4.33 110 1.29 0.598 1" 25 1.63 41 4.53 115 1.40 0.629 1-1/8" 28 1.75 44 4.92 125 1.91 0.8510 1-1/4" 32 2.00 51 5.51 140 3.04 1.3511 1-3/8" 36 2.50 64 5.91 150 4.75 2.1114 1-3/4" 43 3.00 76 7.62 193.5 16.48 7.4918 2-1/4" 57 3.75 95 8.66 220 17.82 8.1020 2-1/2" 63.5 4.00 102 10.24 260 21.37 9.5024 3" 75 4.50 114 11.81 300 27.55 12.5028 3-1/2" 90 5.00 127 13.40 340 33.60 15.2532 4" 100 5.50 140 15.00 380 45.50 20.64

# inch mm inch mm inch mm lbs. kg6 3/4" 19 1.50 38.1 0.79 20 0.18 0.087 7/8" 22 1.50 38.1 0.87 22 0.22 0.108 1" 25 1.75 44.5 0.91 23 0.33 0.159 1-1/8" 28 2.00 50.8 0.98 25 0.37 0.1710 1-1/4" 32 2.25 57.2 1.18 30 0.75 0.3411 1-3/8" 36 2.50 63.5 1.38 35 1.08 0.4914 1-3/4" 43 3.00 76.2 1.57 40 1.52 0.6918 2-1/4" 57 3.50 90 2.36 60 4.11 1.8720 2-1/2" 63.5 4.00 100 2.95 75 5.74 2.6124 3" 75 4.00 100 3.15 80 6.38 2.9028 3-1/2" 90 5.25 133 3.50 90 12.90 5.8632 4" 100 5.50 140 4.00 100 15.20 6.87

Lock Nut

Size Nominal DiameterWrench Size

(F)

Length

(L)

Weight

®

®

Page 8: CTS® Drilled Shaft Reinforcement - Con-Tech Systems · any of your project needs. ... page 2 Contents: Company Introducion: Cover ... 2. Utilization of a CTS®/IBO® Hollow Bar as

CTS® Drilled Shaft Reinforcement

... page 9

GRADE 80 & 100 ACCESSORIES NOTES:

• All Couplers and Hex Nuts develop the Guaranteed Ultimate Tensile Strength (GUTS) of the Bars.

• Bars must be engaged half of the Coupler length. If Bars are torqued against each other no Nuts are required. (Note: For the various torque values please contact Con-Tech Systems® directly.)

• If Bars are not torqued, and the splice has to develop the GUTS of the Bar in tension and compression, Hex Nuts shall be used and tightened against each end of the Coupler. If Lock Nuts are used instead of Hex Nuts the splice will develop the GUTS of the Bar in tension but only 50% of the GUTS of the Bar in compression.

• Reduction couplers are available upon request.

• These diameters and wrench sizes are calculated for machined parts made in the USA. Cast material and acces-

sories made in metric sizes maybe have some variation from the published numbers on this page.

Accessories: Grade 80 left hand thread

# inch mm inch mm inch mm lbs. kg6 3/4" 19 1.50 38 4.13 105 1.14 0.527 7/8" 22 1.50 38 4.33 110 1.29 0.598 1" 25 1.63 41 4.53 115 1.40 0.629 1-1/8" 28 1.75 44 4.92 125 1.91 0.8510 1-1/4" 32 2.00 51 5.51 140 3.04 1.3511 1-3/8" 36 2.50 64 5.91 150 4.75 2.1114 1-3/4" 43 3.00 76 7.62 193.5 16.48 7.4918 2-1/4" 57 3.75 95 8.66 220 17.82 8.1020 2-1/2" 63.5 4.00 102 10.24 260 21.37 9.5024 3" 75 4.50 114 11.81 300 27.55 12.5028 3-1/2" 90 5.00 127 13.40 340 33.60 15.2532 4" 100 5.50 140 15.00 380 45.50 20.64

# inch mm inch mm inch mm lbs. kg6 3/4" 19 1.50 38.1 0.79 20 0.18 0.087 7/8" 22 1.50 38.1 0.87 22 0.22 0.108 1" 25 1.75 44.5 0.91 23 0.33 0.159 1-1/8" 28 2.00 50.8 0.98 25 0.37 0.1710 1-1/4" 32 2.25 57.2 1.18 30 0.75 0.3411 1-3/8" 36 2.50 63.5 1.38 35 1.08 0.4914 1-3/4" 43 3.00 76.2 1.57 40 1.52 0.6918 2-1/4" 57 3.50 90 2.36 60 4.11 1.8720 2-1/2" 63.5 4.00 100 2.95 75 5.74 2.6124 3" 75 4.00 100 3.15 80 6.38 2.9028 3-1/2" 90 5.25 133 3.50 90 12.90 5.8632 4" 100 5.50 140 4.00 100 15.20 6.87

Accessories Grade 80 (left hand thread)

Coupler

Size Nominal DiameterOutside Diameter

(D)

Length

(L)

Weight

Page 9: CTS® Drilled Shaft Reinforcement - Con-Tech Systems · any of your project needs. ... page 2 Contents: Company Introducion: Cover ... 2. Utilization of a CTS®/IBO® Hollow Bar as

... page 10

Accessories: Grade 100 right hand thread

CTS® Drilled Shaft Reinforcement

# inch mm inch mm inch mm lbs. kg7 7/8" 22 1 5/8" 41.25 1.97 50 0.8 0.368 1" 25 1 7/8" 47.5 2.17 55 1.15 0.529 1-1/8" 28 2" 50 2.36 60 1.45 0.66

10 1-1/4" 30 2 1/4" 57 2.56 65 1.94 0.8811 1-3/8" 35 2 1/2" 63.5 2.76 70 3.27 1.4814 1-3/4" 43 3 1/4" 82.5 3.54 90 6.11 2.7718 2-1/4" 57 3 1/2" 90 4.72 120 10 4.5420 2-1/2" 63.5 4" 108 5.71 145 16.4 7.4424 3" 75 4" 108 5.71 145 11.7 5.31

# inch mm inch mm inch mm inch mm lbs. kg7 7/8" 22 1.42 36 2.09 53 1.77 45 0.59 0.278 1" 25 1.61 41 2.32 59 1.97 50 0.86 0.399 1-1/8" 28 1.81 46 2.64 67 2.17 55 1.19 0.54

10 1-1/4" 30 1.97 50 2.80 71 2.36 60 1.45 0.6611 1-3/8" 35 2.36 60 3.27 83 2.76 70 2.46 1.1214 1-3/4" 43 2.76 70 4.02 102 3.35 85 4.20 1.91

Anchor Nut

Accessories Grade 100 (right hand thread)

Wrench Size

(F)Size Nominal Diameter

Length

(L)Weight

Hex Nut

# inch mm inch mm inch mm lbs. kg7 7/8" 22 1.57 40 3.94 100 1.54 0.708 1" 25 1.77 45 4.72 120 2.20 1.009 1-1/8" 28 1.97 50 5.51 140 3.09 1.40

10 1-1/4" 30 2.17 55 5.91 150 4.08 1.8511 1-3/8" 35 2.56 65 6.69 170 6.83 3.1014 1-3/4" 43 3.15 80 7.87 200 12.24 5.5518 2-1/4" 57 3.94 100 9.84 250 22.05 10.0020 2-1/2" 63.5 4.53 115 11.81 300 36.38 16.5024 3" 75 4.33 110 11.81 300 27.56 12.50

# inch mm inch mm inch mm lbs. kg7 7/8" 22 1 5/8" 41.25 0.87 22 0.22 0.18 1" 25 1 7/8" 47.5 0.98 25 0.35 0.169 1-1/8" 28 2" 50 1.18 30 0.57 0.26

10 1-1/4" 30 2 1/4" 57 1.18 30 0.66 0.311 1-3/8" 35 2 1/2" 63.5 1.57 40 1.10 0.5014 1-3/4" 43 3 1/4" 82.5 1.97 50 2.42 1.118 2-1/4" 57 3 1/2" 90 2.36 60 5.06 2.320 2-1/2" 63.5 4" 108 2.76 70 6.91 3.1424 3" 75 4" 108 3.15 80 7.70 3.5

Lock Nut

Size Nominal DiameterWrench Size

(F)

Length

(L)Weight

®

®

Page 10: CTS® Drilled Shaft Reinforcement - Con-Tech Systems · any of your project needs. ... page 2 Contents: Company Introducion: Cover ... 2. Utilization of a CTS®/IBO® Hollow Bar as

CTS® Drilled Shaft Reinforcement

... page 11

Accessories: Grade 100 right hand thread

# inch mm inch mm inch mm lbs. kg7 7/8" 22 1.57 40 3.94 100 1.54 0.708 1" 25 1.77 45 4.72 120 2.20 1.009 1-1/8" 28 1.97 50 5.51 140 3.09 1.40

10 1-1/4" 30 2.17 55 5.91 150 4.08 1.8511 1-3/8" 35 2.56 65 6.69 170 6.83 3.1014 1-3/4" 43 3.15 80 7.87 200 12.24 5.5518 2-1/4" 57 3.94 100 9.84 250 22.05 10.0020 2-1/2" 63.5 4.53 115 11.81 300 36.38 16.5024 3" 75 4.33 110 11.81 300 27.56 12.50

# inch mm inch mm inch mm lbs. kg7 7/8" 22 1 5/8" 41.25 0.87 22 0.22 0.18 1" 25 1 7/8" 47.5 0.98 25 0.35 0.169 1-1/8" 28 2" 50 1.18 30 0.57 0.26

10 1-1/4" 30 2 1/4" 57 1.18 30 0.66 0.311 1-3/8" 35 2 1/2" 63.5 1.57 40 1.10 0.5014 1-3/4" 43 3 1/4" 82.5 1.97 50 2.42 1.118 2-1/4" 57 3 1/2" 90 2.36 60 5.06 2.320 2-1/2" 63.5 4" 108 2.76 70 6.91 3.1424 3" 75 4" 108 3.15 80 7.70 3.5

Accessories Grade 100 (right hand thread)

Coupler

Size Nominal DiameterOutside Diameter

(D)

Length

(L)Weight

Couplers splicing Hot Rolled Thread Bars together in Drilled Shaft Cage

Page 11: CTS® Drilled Shaft Reinforcement - Con-Tech Systems · any of your project needs. ... page 2 Contents: Company Introducion: Cover ... 2. Utilization of a CTS®/IBO® Hollow Bar as

Version: July 2017

Website: www.contechsystems.com

Head Office: Sales & Production:• 8150 River Road, Delta, B.C., Canada, V4G 1B5 Tel: 604-946-5571

Toll Free: 1-888-818-4826Email: [email protected]

Eastern Locations: Sales & Production: • Brockville, ON, Canada

Tel: 613-342-0041• Charlotte, NC, USA

Tel: 704-494-3989

Toll Free: 1-888-818-4826Email: [email protected]

Western Locations: Sales & Production Plant:• 3736 South Tacoma Way, Tacoma, WA, 98409, USA Tel: 253-237-9008

Toll Free: 1-888-818-4826Email: [email protected]

Memberships: