ctASTl F-ClampPREFORMED AND OPEN END PUNCH-TYPE HOSE CLAMPS

FAST LOK Open End Clamp

Preformed Clamps are double wrapped and formed to a given diameter. Used primarily where one end of the hose or article is free to allow the clamps to be slid over the hose end before the fitting is inserted. Preformed clamps range in size from 13/16 inch I.D. to 8 inch I.D.; all clamps may be pulled down to a smaller diameter but cannot be adjusted to a larger diameter.

Open End Clamps are of the same general construction as the preformed clamps with this exception, the double wrapping of the band around the hose or article is a part of the application. The open end clamps are used when one end or both, of the article to be clamped Is not free, or an obstruction prevents slipping a preformed clamp over the end. Open End Clamps range in size from 13/16 inch I.D. to 48 inch I.D.

Galvanized Preformed Clamps 2 1 /2 Inch I.D. and above, and 5/8" wide open end clamps have a stainless steel lok for greater strength and rigidity.

AVAILABLE IN YOUR AREA FROM

FAST LOK Preformed Clamp

Double-Wrapped Triple-Punched Holds Permanently

Ask for a current price list at your distributor or

write for literature.

GALVANIZED

STEEL

Catalog Number F-3 F-311F-4F-5

F-CLAMPREFORMED CLAMPS

(3/8 11 AND 5/8" (NOMINAL) WIDTH)

Band Width Clamp 1.0. Clamps & Thickness Inches Per Pkg.

3/o X .025 13/16 11 100 3/a X .025 13/a" 100 5/a X .025 111 100 5/a X .025 1" 100

STAINLESS STEEL

Catalog Number

--

FS-3 FS-311 FS-4 FS-5

Band Width & Thickness 3/a X .020 3/e X .020 5/e X .022 5/9 X .022

HEAVY DUTY BANDS F-6 5/e X .031 1" 100 FS-6 5/a X .022 F-7 6/9 X .031 1" 100 FS-7 5/a X .022 F-8 5/a X .031 2" 100 FS-8 5/a X .022 F-9 5/e X .031 2" 100 FS-9 5/a X .022

WITH STAINLESS STEEL LOKS F-10 5/e X .031 2" 50 FS-10 5/a X .022 F-11 5/a X .031 2" 50 FS-11 5/o X .022 F-12 5/e X .031 311 50 FS-12 5/e X .022 F-14 5/9 X .031 3" 50 FS-14 5/e X .022 F-16 6/a X .031 4"' 25 FS-16 5/e X .022 F-18 5/a X .031 4" 25 FS-18 5/e X .022 F-20 5/e X .031 5" 25 FS-20 5/a X .022 F-24 6/a X .031 6" 25 FS-24 5/a X .022 F-28 5/e X .031 7" 25 FS-28 5/a X .022 F-32 5/a X .031 8" 25 FS-32 5/a X .022

OPEN END CLAMPS

(3/8" AND 5/8 11 (NOMINAL) WIDTH) GALVANIZED STEEL

Catalog NumberF0-3 F0-311 F0-316 F0-325

Band Width & Thickness3/9 X .022 3/a X .022 3/9 X .022 3/e X .022

iwlTH STAINLESS STEEL LOKS F0-8 5/a X .025 F0-10 I 5/e X .025

HEAVY DUTY BANDS F0-12 5/e x.031 F0-14 5/e X .031 F0-16 5/e X .031 F0-18 5/a X .031F0-20 5/a X .031F0-24 5/a X .031 F0-28 o/a X .031 F0-32 % X .031 F0-36 o/e X .031 F0-40 5/e x.031 F0-48 o/a X .031 F0-56 5/a X .031 F0-64 5/e X .031 F0-72 o/s X ,031 F0-80 o/a X .031 F0-96 5/a X .031 F0-120 5/e X .031 F0-144 5/s X ,031 F0-168 5/a X .031 F0-192 o/e X .031

Clamp I.D.Inches 13/16" 13/8 112" 31/e

2" 2 11

3" 3 11 411 4 11 511 5117115 11 911

10 11 12" 14" 16" 18" 20 11 24" 30 11 36 11 42 11 48"

Clamps Per Pkg.100 100 100 100

100 50

50 50 50 50 25 25 25 25 25 25 25 10 10 10 10 10 10 10 10 10

STAINLESS STEEL

Catalog Number

FOS-3 FOS-311 FOS-316 FOS-325

FOS-8 FOS-10

FOS-12 FOS-14 FOS-16 FOS-18 FOS-20 FOS-24 FOS-28FOS-32 FOS-36 FOS-40 FOS-48 FOS-56 FOS-64 FOS-72 FOS-80 FOS-96 FOS-120 FOS-144 FOS-168 FOS-192

I Band Width & Thickness 3/a X .020 3/e X .020 3/9 X .020 3/e X .020

5/e X .022 5/a X .022

5/a X .022 6/a X .022 5/9 X .022 5/a X .022 5/e X .022 5/e X .022 6/9 X .022 6/a X .022 5/e X .022 5/a X .022 5/a X .022 o/e X .022 5/s X .022 5/e X .022 5/a X .022 o/s X .022 5/e X .022 5/e X .022 5/e X .022 % X .022

and TOOL PREFORMED AND OPEN END CLA.MPS are available in various materials and widths to satisfy a wide variety of applications; Galvanized Steel and Stainless Steel; 3/8" & 5/8" (Nominal) widths.

TO ORDER the correct size Fast Lok Clamps, measure the outside diameter of the hose or article and then select the next larger inside diameter clamp by catalog number.

APPLICATION TOOLS available from FastLok: For 3/8" and 5/8" widths ... F-38, F-40, F-100.

F-38

Laking Tool

Intermediate sizetool with antiback lash ratchet.

F-100

Laking Tool (Revised F-1)

t F-225Mallet

a

IDEAL CLAMP PRODUCTS, INC. 8100 TRIDON DRIVE SMYRNA, TN 37167 800-251-3220 | 615-459-5800

PREFORMED HOSE CLAMPS

Punch Indentation for ease .of center pu ..

Heavy Duty Lok for greater strength and rigidity

K-Clamps may be secured by either a punch or fold-up method.(See cross sectioned views below)

Center Punched Fold-up

Less tension loss. Patented hole in inner band gives better internal mechanical locking after punching. AVAILABLE IN YOUR AREA FROM

Ask for a current price 11st at your distributor or

write for literature.

K-CLAMPS and TOOLS

GALVANIZED

STEEL

Catalog Number

K-3K-311K-4K-5K-6K-7K-8K-9K10 K-11K-12K-14K-16K-18K-20K-24K-28K-32

PREFORMED CLAMPS

(3/8" AND 5/8" (NOMINAL} WIDTH}

Clamp 1.0. Inches 13/16 tl

1" 1" 1" 1" 1tl

2" 2" 2" 2tl

3" 3" 4"

41/2 ti

5" 6" 7t1

Btl

Band Width & Thickness 3/a" X .025 3/a" X .025 5/a t1 X .0305/a" X .030 5/a" X .030 5/a" X .030 5/a t1 X .030%

t1 X .030 5/a" X .030 5/a t1 X .030 5/a t1 X .030 5/a" X .030 51a t1 X .0305/a t1 X .030 5/a" X .030 51a t1 X .0305/a" X .030 5/a" X .030

Clamps per Pka.

100 100 100 100 100 100 100 100

50 50 50 50 25 25 25 25 25 25

PREFORMED CLAMPS

(3/4" (NOMINAL} WIDTH}

STAINLESS

STEEL

TYPE 301

Catalog Number

KS-3 l

he [?[bJ-Cla PREFORMED HOSE CLAMPS

KA001

FOLD-UP ADAPTER

KS001

WIND-UP TOOL

J-Clamps are available in 3/a", 5/a" and" widths, from 13/15" to 8"I.D. These none punch type clamps are to be secured by the foldup method, using the WIND-UP tool, our part no. KS001 andadapter KA001.

LA

PREFORMED CLAMPS

GALVANIZED STAINLESS

STEEL STEEL

3/8" ( NOMINAL WIDTH ) TYPE 301

CATALOG CLAMP I.D. BAND WIDTH CLAMPS CATALOG

NUMBER INCHES

FLJ 301 13/16"

FLJ 343 1II

FLJ 302 1 3/8"

FLJ 345 2"

FLJ 346 3"

N/A 3 1 /4"

FLJ 303 1 "

FLJ 304 1 1 /4"

FLJ 305 1 1 /2"

FLJ 306 1 3/4"

FLJ 307 2"

FLJ 308 2 1 /4"

FLJ 309 2 1 /2"

FLJ 327 2"

FLJ 310 2 3/4"

FLJ 311 3"

FLJ 312 3 1/2"

FLJ 313 4"

FLJ 314 4 1 /2"

FLJ 315 5"

FLJ 316 6"

FLJ 318 7"

FLJ 319 8"

IDEAL CLAMP PRODUCTS, INC. 8100 TRIDON DRIVE SMYRNA, TN 37167 800-251-3220 | 615-459-5800

& THICKNESS PER PKG. NUMBER

3/8" X .025 100 FLJ 201

3/8" X .025 100 FLJ 243

3/8" X .025 100 FLJ 202

3/8" X .025 100 FLJ 245

3/8" X .025 100 FLJ 246

3/8" X .025 100 FLJ 255

5/8" ( NOMINAL WIDTH )

5/8" X .030 100 FLJ 203

5/8" X .030 100 FLJ 204

5/8" X .030 100 FLJ 205

5/8" X .030 100 FLJ 206

5/8" X .030 100 FLJ 207

5/8" X .030 100 FLJ 208

5/8" X .030 100 FLJ 209

3/4" ( NOMINAL WIDTH )

3/4" X .030 100 FLJ 227

3/4" X .030 50 FLJ 210

3/4" X .030 50 FLJ 211

3/4" X .030 50 FLJ 212

3/4" X .030 25 FLJ 213

3/4" X .030 25 FLJ 214

3/4" X .030 25 FLJ 215

3/4" X .030 25 FLJ 216

3/4" X .030 25 FLJ 218

3/4" X .030 25 FLJ 219

316 STAINLESS AVAILABLE UPON REQUEST

AVAILABLE IN YOUR AREA FROM

FLJ895

l

e [?f1JS-Cla SMOOTH I.D. CLAMPS

KADD1

FOLD-UP ADAPTER

KS001

WIND-UP TOOL

Fast Lok JS - clamps are double wrapped clamps with a more smooth inside diameter, intended for your thermoplastic and other thinner wall hose clamping applications. The JS series clamps slide on the hose prior to inserting the fitting.

Preformed JS - Clamps are available in 5/a and inch widths, 1 inch I.D. to 8 inch 1.0. in inch increments. The clamps are produced from galvanized or stainless steel, the locks are stainless steel.

The Fast Lok JS - clamp is intended to be applied with a Fast Lok, l

-CL M

SMOOTH I.D. CLAMPS

GALVANIZED STAINLESS

STEEL STEEL

5/8" ( NOMINAL WIDTH) TYPE 301

CATALOG CLAMP I.D. BAND WIDTH CLAMPS CATALOG

NUMBER INCHES & THICl

Please use the Part Numbers when placing orders. (The illustrations are not in correct proportion to one another).

QTY. Part Per Tool Descri tion

Punch Head 1 Punch 1 Punch Head Pin 1 Pusher Nose 1 Holding Dog 1 Pusher Nose Pin 1 Holding Dog Spring 2 Puller Links 2 Puller Links

Puller Link Pin Pulling Dog Pulling Dog Spring Pulling Dog Pin

1 Ball Handle Assy 1 3/8" Clamp Adapter

Pusher Puller Assy 3 Retaining Rings

Cresent Ring Punch Retainer Ring

1 Pulling Dog 1 Pulling Dog Spring 2 Puller Links 2 Puller Links

VIEW1

(

VIEW3

Part Number F-202

FX-201 F-202F-233F-206F-207

F-208

F-208 FX-211 B F-212

F-209

/FY-214

F-206

FX-211 A

FY-217F-209

FX-211AFX-211 B F-212FY-214FY-217F-233

F-233

' FA-220 F-242

FA-220

. F-232

F-229HT FA-231

F-235

F-229HT0 C 0 FA-231

F-242F-232F-235

Sliding Jack Replacement Kit No. FY205K FY-214 FY-217 FX- 211A FX-2118

(Kit Fits The F-1,F-100, F-175, & the C-2 Tools)

INSTRUCTIONS FOR OPERATING

TOOL No. F-100

Hold Laking Tool as shown with b