Multi 9CT modular contactors Modular contactors are not only used in the residential sector but in the commercial sector or in industrial utilities for the control of single or three-phase loads up to 100 A. They act as an interface between the order giver (e.g. power utility signal, load-shedding device, pushbutton, thermostat, programmable time switch, centralised technical management,…) and the power circuit for final circuits: lighting, utility motors: ventilation, heat pumps, watering systems, hot water, heating, ovens, climatic chambers…

Operation with normally open poles (N/O), pole closing is controlled by the >presence of voltage on the coil and pole opening by the disappearance of this voltage, with normally closed poles (N/C), the poles are closed with the coil >de-energized and open when the coil is fed with power.

Advantages A complete range of modular contactors:

16 to 100 A ratings in single, two, three or four-pole. >Closing, opening or mixed poles. >Comply with the standards in residential and tertiary applications: >EN 61095 and IEC 1095. Silent (< 20 dB). >With an adaptable indication auxiliary for 25 to 100 A contactors. >With control auxiliaries compatible with the reverser relay range and >remote control of the C60 circuit-breaker. Anti-interference filter. >With accessories: screw cover, clip-on markers, spacers. >Homogenous with the entire Multi 9 offer: >- matching design, - same profile, - identical connections.

The rangetime delayATEt

anti-interferenceACTp

ACTo+f

impulse/latched control ACTc

Schematic diagrams ImplementationDesigned to be installed in modular switch >boxes and switchboards.Optimised dimensions: in accordance with the >rating and number of poles.Easy symmetrical rail mounting using a >two-state latch.Easy connection using grooved tunnel terminals >with flap.Mixed +/- socket screws which cannot be lost. >Auxiliaries simply clipped on to contactors. >

SpecificationsElectrical specifications

Power circuit: >rating at 40°C: 16 to 100 A (AC7a category).Control circuit: >- operating voltage: - 24 V AC ± 10%, - 230/240 V AC: -15% +6%, - coil frequency: 50 Hz. Electrical endurance: >- AC1 and AC7a categories: - 16 A ratings, 100,000 operations, - 25 A ratings, 250,000 operations, - 40-63-100 A ratings, 200,000 operations.

Mechanical specifications Visualisation of contactor state on front panel. >Connections: >- control circuit: - rigid cable: 2 x 1.5 mm2, - flexible cable: 2 x 2.5 mm2, - power circuit: rigid cable: - 6 mm2 up to 25 A, - 25 mm2 for 40 and 63 A, - 50 mm2 for 100 A. flexible cable: - 2 x 2.5 mm2 up to 25 A, - 2 x 10 mm2 for 40 and 63 A, - 6 to 35 mm2 for 100 A.

EnvironmentTropicalisation: treatment 2 >(relative humidity: 95% at 55°C ). Protection class: IP 201 (front panel: IP 4). >Operating temperature: -5°C to +50°C. >Storage temperature: -40°C to +70°C. >Complies with the strictest regulations and >directives in the area of “environmental protection”.

132371

© Schneider Electric 2008

Choice tableNumber Power circuit Width Type of Control Referencesof poles Rating

(A)Voltage (V AC)

in mod. (of 9mm)

contacts circuit voltage (V AC)

1P 25 250 2 1C 230/240 15958

2P 16 250 2 1C+1O 230/240 15956

2 2C 230/240 15957

25 250 2 2C 230/240 15959

2 2C 24 16020

2 2O 230/240 15960

40 250 4 2C 230/240 15966

63 250 4 2C 230/240 15971

4 2C 24 16024

100 250 6 2C 230/240 15977

3P 25 400 4 3C 230/240 15961

40 400 6 3C 230/240 15967

63 400 6 3C 230/240 15972

4P 25 400 4 4C 230/240 15962

4 4C 24 16022

4 4O 230/240 15963

4 4O 24 16023

4 2C+2O 230/240 15964

40 400 6 4C 230/240 15968

6 4O 230/240 15969

63 400 6 4C 230/240 15973

6 4C 24 16025

6 4O 230/240 15974

6 4O 24 16026

6 2C+2O 230/240 15975

100 400 12 4C 230/240 15978

1-pole (1N/O)

EnvironmentEnvironmentc Tropicalisation:treatment 2 (relative humidity: 95% at 55°C ).c Protection class:IP 201 (front panel: IP 4).c Operating temperature:-5°C to +50°C.c Storage temperature:-40°C to +70°C.c Complies with the strictest regulations anddirectives in the area of «environmentalprotection».

4-pole (4C)manual op. mech.

3-pole (3C)manual op. mech.

2-pole (2C)manual op. mech.

4-pole (2C+2O)

4-pole (4O)4-pole (4C)3-pole (3C)

2-pole (2O)2-pole (2C)2-pole (1C+1O)1-pole (1C)

Schematic diagrams

Selection table

Approvals

Specifications

Implementation

As standards, specifications and designs change from time totime, please ask for confirmation of the information given in thispublication.

Publication: Communication BT-S2ECreated by: Sodipe (38)

Merlin GerinF-38050 Grenoble cedex 9tel. +33 (0)4 76 57 60 60telex : merge 320 842 F

Schneider Electric SA

03/00

M9F

P46

AE

N

DIT E D1 97 010 enART. 078255

This document has beenprinted on ecologicalpaper

SpecificationsElectrical specificationsc Power circuit:rating at 40°C: 16 to 100 A (AC7a category).c Control circuit:v operating voltage:- 24 V AC ± 10%- 230/240 V AC: -15% +6%,v coil frequency: 50 Hz.c Electrical endurance:v AC1 and AC7a categories:- 16 A ratings, 100,000 operations- 25 A ratings, 250,000 operations- 40-63-100 A ratings, 200,000 operations.Mechanical specificationsc Visualisation of contactor state on front panel(coil fed or manual operation).c Mechanical endurance: 1,000,000 operations.c Connections:v control circuit:- rigid cable: 2 x 1.5 mm2

- supple cable: 2 x 2.5 mm2,v power circuit:- rigid cable:6 mm2 up to 25 A25 mm2 for 40 and 63 A50 mm2 for 100 A- supple cable:2 x 2.5 mm2 up to 25 A2 x 10 mm2 for 40 and 63 A2 x 35 mm2 for 100 A.

Schematic diagrams

Approvals

1A1

A2 2

1A1

A2 2

3

4

1R1

2R2

A1

A2

R1

R2

A1

A2

R3

R4

Oauto

I P

1A1

A2 2

3

4

5

6

7

8Oauto

I P

1A1

A2 2

3

4

5

6

1A1

A2 2

3

4

5

6

7

8

1A1

A2 2

3

4

5

6

R1

R2

A1

A2

R3

R4

R5

R6

R7

R8

Oauto

I P

1A1

A2 2

3

4

1R1

2R2

A1

A2

3

4

R3

R4

Implementationc Designed to be installed in modular switchboxes and switchboards.c Optimised dimensions: in accordance with therating and number of poles.c Easy symmetrical rail mounting using a two-state latch.c Easy connection using grooved tunnelterminals with flap.c Mixed +/- socket screws which cannot be lost.c Auxiliaries simply clipped on to contactors.

Selection tablenumber power circuit width type of control referencesof poles rating voltage in mod. contacts circuit man. op. mech.

(A) (V AC) (9 mm) voltage (V AC) with without

1P 25 250 2 1C 230/240 15958

2P 16 250 2 1C+1O 230/240 15956

2 2C 230/240 1595725 250 2 2C 230/240 15981 15959

2 2C 24 16020

2 2O 230/240 1596040 250 4 2C 230/240 15984 15966

63 250 4 2C 230/240 15987 15971

4 2C 24 16024100 250 6 2C 230/240 15977

3P 25 400 4 3C 230/240 15982 15961

40 400 6 3C 230/240 1596763 400 6 3C 230/240 15972

4P 25 400 4 4C 230/240 15983 15962

4 4C 24 160224 4O 230/240 15963

4 4O 24 16023

4 2C+2O 230/240 1596440 400 6 4C 230/240 15986 15968

6 4O 230/240 15969

63 400 6 4C 230/240 15988 159736 4C 24 16025

6 4O 230/240 15974

6 4O 24 160266 2C+2O 230/240 15975

100 400 12 4C 230/240 15978

EnvironmentEnvironmentc Tropicalisation:treatment 2 (relative humidity: 95% at 55°C ).c Protection class:IP 201 (front panel: IP 4).c Operating temperature:-5°C to +50°C.c Storage temperature:-40°C to +70°C.c Complies with the strictest regulations anddirectives in the area of «environmentalprotection».

4-pole (4C)manual op. mech.

3-pole (3C)manual op. mech.

2-pole (2C)manual op. mech.

4-pole (2C+2O)

4-pole (4O)4-pole (4C)3-pole (3C)

2-pole (2O)2-pole (2C)2-pole (1C+1O)1-pole (1C)

Schematic diagrams

Selection table

Approvals

Specifications

Implementation

As standards, specifications and designs change from time totime, please ask for confirmation of the information given in thispublication.

Publication: Communication BT-S2ECreated by: Sodipe (38)

Merlin GerinF-38050 Grenoble cedex 9tel. +33 (0)4 76 57 60 60telex : merge 320 842 F

Schneider Electric SA

03/00

M9F

P46

AE

N

DIT E D1 97 010 enART. 078255

This document has beenprinted on ecologicalpaper

SpecificationsElectrical specificationsc Power circuit:rating at 40°C: 16 to 100 A (AC7a category).c Control circuit:v operating voltage:- 24 V AC ± 10%- 230/240 V AC: -15% +6%,v coil frequency: 50 Hz.c Electrical endurance:v AC1 and AC7a categories:- 16 A ratings, 100,000 operations- 25 A ratings, 250,000 operations- 40-63-100 A ratings, 200,000 operations.Mechanical specificationsc Visualisation of contactor state on front panel(coil fed or manual operation).c Mechanical endurance: 1,000,000 operations.c Connections:v control circuit:- rigid cable: 2 x 1.5 mm2

- supple cable: 2 x 2.5 mm2,v power circuit:- rigid cable:6 mm2 up to 25 A25 mm2 for 40 and 63 A50 mm2 for 100 A- supple cable:2 x 2.5 mm2 up to 25 A2 x 10 mm2 for 40 and 63 A2 x 35 mm2 for 100 A.

Schematic diagrams

Approvals

1A1

A2 2

1A1

A2 2

3

4

1R1

2R2

A1

A2

R1

R2

A1

A2

R3

R4

Oauto

I P

1A1

A2 2

3

4

5

6

7

8Oauto

I P

1A1

A2 2

3

4

5

6

1A1

A2 2

3

4

5

6

7

8

1A1

A2 2

3

4

5

6

R1

R2

A1

A2

R3

R4

R5

R6

R7

R8

Oauto

I P

1A1

A2 2

3

4

1R1

2R2

A1

A2

3

4

R3

R4

Implementationc Designed to be installed in modular switchboxes and switchboards.c Optimised dimensions: in accordance with therating and number of poles.c Easy symmetrical rail mounting using a two-state latch.c Easy connection using grooved tunnelterminals with flap.c Mixed +/- socket screws which cannot be lost.c Auxiliaries simply clipped on to contactors.

Selection tablenumber power circuit width type of control referencesof poles rating voltage in mod. contacts circuit man. op. mech.

(A) (V AC) (9 mm) voltage (V AC) with without

1P 25 250 2 1C 230/240 15958

2P 16 250 2 1C+1O 230/240 15956

2 2C 230/240 1595725 250 2 2C 230/240 15981 15959

2 2C 24 16020

2 2O 230/240 1596040 250 4 2C 230/240 15984 15966

63 250 4 2C 230/240 15987 15971

4 2C 24 16024100 250 6 2C 230/240 15977

3P 25 400 4 3C 230/240 15982 15961

40 400 6 3C 230/240 1596763 400 6 3C 230/240 15972

4P 25 400 4 4C 230/240 15983 15962

4 4C 24 160224 4O 230/240 15963

4 4O 24 16023

4 2C+2O 230/240 1596440 400 6 4C 230/240 15986 15968

6 4O 230/240 15969

63 400 6 4C 230/240 15988 159736 4C 24 16025

6 4O 230/240 15974

6 4O 24 160266 2C+2O 230/240 15975

100 400 12 4C 230/240 15978

2-pole (1N/C+1N/O)

EnvironmentEnvironmentc Tropicalisation:treatment 2 (relative humidity: 95% at 55°C ).c Protection class:IP 201 (front panel: IP 4).c Operating temperature:-5°C to +50°C.c Storage temperature:-40°C to +70°C.c Complies with the strictest regulations anddirectives in the area of «environmentalprotection».

4-pole (4C)manual op. mech.

3-pole (3C)manual op. mech.

2-pole (2C)manual op. mech.

4-pole (2C+2O)

4-pole (4O)4-pole (4C)3-pole (3C)

2-pole (2O)2-pole (2C)2-pole (1C+1O)1-pole (1C)

Schematic diagrams

Selection table

Approvals

Specifications

Implementation

As standards, specifications and designs change from time totime, please ask for confirmation of the information given in thispublication.

Publication: Communication BT-S2ECreated by: Sodipe (38)

Merlin GerinF-38050 Grenoble cedex 9tel. +33 (0)4 76 57 60 60telex : merge 320 842 F

Schneider Electric SA

03/00

M9F

P46

AE

N

DIT E D1 97 010 enART. 078255

This document has beenprinted on ecologicalpaper

SpecificationsElectrical specificationsc Power circuit:rating at 40°C: 16 to 100 A (AC7a category).c Control circuit:v operating voltage:- 24 V AC ± 10%- 230/240 V AC: -15% +6%,v coil frequency: 50 Hz.c Electrical endurance:v AC1 and AC7a categories:- 16 A ratings, 100,000 operations- 25 A ratings, 250,000 operations- 40-63-100 A ratings, 200,000 operations.Mechanical specificationsc Visualisation of contactor state on front panel(coil fed or manual operation).c Mechanical endurance: 1,000,000 operations.c Connections:v control circuit:- rigid cable: 2 x 1.5 mm2

- supple cable: 2 x 2.5 mm2,v power circuit:- rigid cable:6 mm2 up to 25 A25 mm2 for 40 and 63 A50 mm2 for 100 A- supple cable:2 x 2.5 mm2 up to 25 A2 x 10 mm2 for 40 and 63 A2 x 35 mm2 for 100 A.

Schematic diagrams

Approvals

1A1

A2 2

1A1

A2 2

3

4

1R1

2R2

A1

A2

R1

R2

A1

A2

R3

R4

Oauto

I P

1A1

A2 2

3

4

5

6

7

8Oauto

I P

1A1

A2 2

3

4

5

6

1A1

A2 2

3

4

5

6

7

8

1A1

A2 2

3

4

5

6

R1

R2

A1

A2

R3

R4

R5

R6

R7

R8

Oauto

I P

1A1

A2 2

3

4

1R1

2R2

A1

A2

3

4

R3

R4

Implementationc Designed to be installed in modular switchboxes and switchboards.c Optimised dimensions: in accordance with therating and number of poles.c Easy symmetrical rail mounting using a two-state latch.c Easy connection using grooved tunnelterminals with flap.c Mixed +/- socket screws which cannot be lost.c Auxiliaries simply clipped on to contactors.

Selection tablenumber power circuit width type of control referencesof poles rating voltage in mod. contacts circuit man. op. mech.

(A) (V AC) (9 mm) voltage (V AC) with without

1P 25 250 2 1C 230/240 15958

2P 16 250 2 1C+1O 230/240 15956

2 2C 230/240 1595725 250 2 2C 230/240 15981 15959

2 2C 24 16020

2 2O 230/240 1596040 250 4 2C 230/240 15984 15966

63 250 4 2C 230/240 15987 15971

4 2C 24 16024100 250 6 2C 230/240 15977

3P 25 400 4 3C 230/240 15982 15961

40 400 6 3C 230/240 1596763 400 6 3C 230/240 15972

4P 25 400 4 4C 230/240 15983 15962

4 4C 24 160224 4O 230/240 15963

4 4O 24 16023

4 2C+2O 230/240 1596440 400 6 4C 230/240 15986 15968

6 4O 230/240 15969

63 400 6 4C 230/240 15988 159736 4C 24 16025

6 4O 230/240 15974

6 4O 24 160266 2C+2O 230/240 15975

100 400 12 4C 230/240 15978

2-pole (2N/O)

EnvironmentEnvironmentc Tropicalisation:treatment 2 (relative humidity: 95% at 55°C ).c Protection class:IP 201 (front panel: IP 4).c Operating temperature:-5°C to +50°C.c Storage temperature:-40°C to +70°C.c Complies with the strictest regulations anddirectives in the area of «environmentalprotection».

4-pole (4C)manual op. mech.

3-pole (3C)manual op. mech.

2-pole (2C)manual op. mech.

4-pole (2C+2O)

4-pole (4O)4-pole (4C)3-pole (3C)

2-pole (2O)2-pole (2C)2-pole (1C+1O)1-pole (1C)

Schematic diagrams

Selection table

Approvals

Specifications

Implementation

As standards, specifications and designs change from time totime, please ask for confirmation of the information given in thispublication.

Publication: Communication BT-S2ECreated by: Sodipe (38)

Merlin GerinF-38050 Grenoble cedex 9tel. +33 (0)4 76 57 60 60telex : merge 320 842 F

Schneider Electric SA

03/00

M9F

P46

AE

N

DIT E D1 97 010 enART. 078255

This document has beenprinted on ecologicalpaper

SpecificationsElectrical specificationsc Power circuit:rating at 40°C: 16 to 100 A (AC7a category).c Control circuit:v operating voltage:- 24 V AC ± 10%- 230/240 V AC: -15% +6%,v coil frequency: 50 Hz.c Electrical endurance:v AC1 and AC7a categories:- 16 A ratings, 100,000 operations- 25 A ratings, 250,000 operations- 40-63-100 A ratings, 200,000 operations.Mechanical specificationsc Visualisation of contactor state on front panel(coil fed or manual operation).c Mechanical endurance: 1,000,000 operations.c Connections:v control circuit:- rigid cable: 2 x 1.5 mm2

- supple cable: 2 x 2.5 mm2,v power circuit:- rigid cable:6 mm2 up to 25 A25 mm2 for 40 and 63 A50 mm2 for 100 A- supple cable:2 x 2.5 mm2 up to 25 A2 x 10 mm2 for 40 and 63 A2 x 35 mm2 for 100 A.

Schematic diagrams

Approvals

1A1

A2 2

1A1

A2 2

3

4

1R1

2R2

A1

A2

R1

R2

A1

A2

R3

R4

Oauto

I P

1A1

A2 2

3

4

5

6

7

8Oauto

I P

1A1

A2 2

3

4

5

6

1A1

A2 2

3

4

5

6

7

8

1A1

A2 2

3

4

5

6

R1

R2

A1

A2

R3

R4

R5

R6

R7

R8

Oauto

I P

1A1

A2 2

3

4

1R1

2R2

A1

A2

3

4

R3

R4

Implementationc Designed to be installed in modular switchboxes and switchboards.c Optimised dimensions: in accordance with therating and number of poles.c Easy symmetrical rail mounting using a two-state latch.c Easy connection using grooved tunnelterminals with flap.c Mixed +/- socket screws which cannot be lost.c Auxiliaries simply clipped on to contactors.

Selection tablenumber power circuit width type of control referencesof poles rating voltage in mod. contacts circuit man. op. mech.

(A) (V AC) (9 mm) voltage (V AC) with without

1P 25 250 2 1C 230/240 15958

2P 16 250 2 1C+1O 230/240 15956

2 2C 230/240 1595725 250 2 2C 230/240 15981 15959

2 2C 24 16020

2 2O 230/240 1596040 250 4 2C 230/240 15984 15966

63 250 4 2C 230/240 15987 15971

4 2C 24 16024100 250 6 2C 230/240 15977

3P 25 400 4 3C 230/240 15982 15961

40 400 6 3C 230/240 1596763 400 6 3C 230/240 15972

4P 25 400 4 4C 230/240 15983 15962

4 4C 24 160224 4O 230/240 15963

4 4O 24 16023

4 2C+2O 230/240 1596440 400 6 4C 230/240 15986 15968

6 4O 230/240 15969

63 400 6 4C 230/240 15988 159736 4C 24 16025

6 4O 230/240 15974

6 4O 24 160266 2C+2O 230/240 15975

100 400 12 4C 230/240 15978

2-pole (2N/C)

EnvironmentEnvironmentc Tropicalisation:treatment 2 (relative humidity: 95% at 55°C ).c Protection class:IP 201 (front panel: IP 4).c Operating temperature:-5°C to +50°C.c Storage temperature:-40°C to +70°C.c Complies with the strictest regulations anddirectives in the area of «environmentalprotection».

4-pole (4C)manual op. mech.

3-pole (3C)manual op. mech.

2-pole (2C)manual op. mech.

4-pole (2C+2O)

4-pole (4O)4-pole (4C)3-pole (3C)

2-pole (2O)2-pole (2C)2-pole (1C+1O)1-pole (1C)

Schematic diagrams

Selection table

Approvals

Specifications

Implementation

As standards, specifications and designs change from time totime, please ask for confirmation of the information given in thispublication.

Publication: Communication BT-S2ECreated by: Sodipe (38)

Merlin GerinF-38050 Grenoble cedex 9tel. +33 (0)4 76 57 60 60telex : merge 320 842 F

Schneider Electric SA

03/00

M9F

P46

AE

N

DIT E D1 97 010 enART. 078255

This document has beenprinted on ecologicalpaper

SpecificationsElectrical specificationsc Power circuit:rating at 40°C: 16 to 100 A (AC7a category).c Control circuit:v operating voltage:- 24 V AC ± 10%- 230/240 V AC: -15% +6%,v coil frequency: 50 Hz.c Electrical endurance:v AC1 and AC7a categories:- 16 A ratings, 100,000 operations- 25 A ratings, 250,000 operations- 40-63-100 A ratings, 200,000 operations.Mechanical specificationsc Visualisation of contactor state on front panel(coil fed or manual operation).c Mechanical endurance: 1,000,000 operations.c Connections:v control circuit:- rigid cable: 2 x 1.5 mm2

- supple cable: 2 x 2.5 mm2,v power circuit:- rigid cable:6 mm2 up to 25 A25 mm2 for 40 and 63 A50 mm2 for 100 A- supple cable:2 x 2.5 mm2 up to 25 A2 x 10 mm2 for 40 and 63 A2 x 35 mm2 for 100 A.

Schematic diagrams

Approvals

1A1

A2 2

1A1

A2 2

3

4

1R1

2R2

A1

A2

R1

R2

A1

A2

R3

R4

Oauto

I P

1A1

A2 2

3

4

5

6

7

8Oauto

I P

1A1

A2 2

3

4

5

6

1A1

A2 2

3

4

5

6

7

8

1A1

A2 2

3

4

5

6

R1

R2

A1

A2

R3

R4

R5

R6

R7

R8

Oauto

I P

1A1

A2 2

3

4

1R1

2R2

A1

A2

3

4

R3

R4

Implementationc Designed to be installed in modular switchboxes and switchboards.c Optimised dimensions: in accordance with therating and number of poles.c Easy symmetrical rail mounting using a two-state latch.c Easy connection using grooved tunnelterminals with flap.c Mixed +/- socket screws which cannot be lost.c Auxiliaries simply clipped on to contactors.

Selection tablenumber power circuit width type of control referencesof poles rating voltage in mod. contacts circuit man. op. mech.

(A) (V AC) (9 mm) voltage (V AC) with without

1P 25 250 2 1C 230/240 15958

2P 16 250 2 1C+1O 230/240 15956

2 2C 230/240 1595725 250 2 2C 230/240 15981 15959

2 2C 24 16020

2 2O 230/240 1596040 250 4 2C 230/240 15984 15966

63 250 4 2C 230/240 15987 15971

4 2C 24 16024100 250 6 2C 230/240 15977

3P 25 400 4 3C 230/240 15982 15961

40 400 6 3C 230/240 1596763 400 6 3C 230/240 15972

4P 25 400 4 4C 230/240 15983 15962

4 4C 24 160224 4O 230/240 15963

4 4O 24 16023

4 2C+2O 230/240 1596440 400 6 4C 230/240 15986 15968

6 4O 230/240 15969

63 400 6 4C 230/240 15988 159736 4C 24 16025

6 4O 230/240 15974

6 4O 24 160266 2C+2O 230/240 15975

100 400 12 4C 230/240 15978

3-pole (3N/O)

EnvironmentEnvironmentc Tropicalisation:treatment 2 (relative humidity: 95% at 55°C ).c Protection class:IP 201 (front panel: IP 4).c Operating temperature:-5°C to +50°C.c Storage temperature:-40°C to +70°C.c Complies with the strictest regulations anddirectives in the area of «environmentalprotection».

4-pole (4C)manual op. mech.

3-pole (3C)manual op. mech.

2-pole (2C)manual op. mech.

4-pole (2C+2O)

4-pole (4O)4-pole (4C)3-pole (3C)

2-pole (2O)2-pole (2C)2-pole (1C+1O)1-pole (1C)

Schematic diagrams

Selection table

Approvals

Specifications

Implementation

As standards, specifications and designs change from time totime, please ask for confirmation of the information given in thispublication.

Publication: Communication BT-S2ECreated by: Sodipe (38)

Merlin GerinF-38050 Grenoble cedex 9tel. +33 (0)4 76 57 60 60telex : merge 320 842 F

Schneider Electric SA

03/00

M9F

P46

AE

N

DIT E D1 97 010 enART. 078255

This document has beenprinted on ecologicalpaper

SpecificationsElectrical specificationsc Power circuit:rating at 40°C: 16 to 100 A (AC7a category).c Control circuit:v operating voltage:- 24 V AC ± 10%- 230/240 V AC: -15% +6%,v coil frequency: 50 Hz.c Electrical endurance:v AC1 and AC7a categories:- 16 A ratings, 100,000 operations- 25 A ratings, 250,000 operations- 40-63-100 A ratings, 200,000 operations.Mechanical specificationsc Visualisation of contactor state on front panel(coil fed or manual operation).c Mechanical endurance: 1,000,000 operations.c Connections:v control circuit:- rigid cable: 2 x 1.5 mm2

- supple cable: 2 x 2.5 mm2,v power circuit:- rigid cable:6 mm2 up to 25 A25 mm2 for 40 and 63 A50 mm2 for 100 A- supple cable:2 x 2.5 mm2 up to 25 A2 x 10 mm2 for 40 and 63 A2 x 35 mm2 for 100 A.

Schematic diagrams

Approvals

1A1

A2 2

1A1

A2 2

3

4

1R1

2R2

A1

A2

R1

R2

A1

A2

R3

R4

Oauto

I P

1A1

A2 2

3

4

5

6

7

8Oauto

I P

1A1

A2 2

3

4

5

6

1A1

A2 2

3

4

5

6

7

8

1A1

A2 2

3

4

5

6

R1

R2

A1

A2

R3

R4

R5

R6

R7

R8

Oauto

I P

1A1

A2 2

3

4

1R1

2R2

A1

A2

3

4

R3

R4

Implementationc Designed to be installed in modular switchboxes and switchboards.c Optimised dimensions: in accordance with therating and number of poles.c Easy symmetrical rail mounting using a two-state latch.c Easy connection using grooved tunnelterminals with flap.c Mixed +/- socket screws which cannot be lost.c Auxiliaries simply clipped on to contactors.

Selection tablenumber power circuit width type of control referencesof poles rating voltage in mod. contacts circuit man. op. mech.

(A) (V AC) (9 mm) voltage (V AC) with without

1P 25 250 2 1C 230/240 15958

2P 16 250 2 1C+1O 230/240 15956

2 2C 230/240 1595725 250 2 2C 230/240 15981 15959

2 2C 24 16020

2 2O 230/240 1596040 250 4 2C 230/240 15984 15966

63 250 4 2C 230/240 15987 15971

4 2C 24 16024100 250 6 2C 230/240 15977

3P 25 400 4 3C 230/240 15982 15961

40 400 6 3C 230/240 1596763 400 6 3C 230/240 15972

4P 25 400 4 4C 230/240 15983 15962

4 4C 24 160224 4O 230/240 15963

4 4O 24 16023

4 2C+2O 230/240 1596440 400 6 4C 230/240 15986 15968

6 4O 230/240 15969

63 400 6 4C 230/240 15988 159736 4C 24 16025

6 4O 230/240 15974

6 4O 24 160266 2C+2O 230/240 15975

100 400 12 4C 230/240 15978

4-pole (4N/O)

EnvironmentEnvironmentc Tropicalisation:treatment 2 (relative humidity: 95% at 55°C ).c Protection class:IP 201 (front panel: IP 4).c Operating temperature:-5°C to +50°C.c Storage temperature:-40°C to +70°C.c Complies with the strictest regulations anddirectives in the area of «environmentalprotection».

4-pole (4C)manual op. mech.

3-pole (3C)manual op. mech.

2-pole (2C)manual op. mech.

4-pole (2C+2O)

4-pole (4O)4-pole (4C)3-pole (3C)

2-pole (2O)2-pole (2C)2-pole (1C+1O)1-pole (1C)

Schematic diagrams

Selection table

Approvals

Specifications

Implementation

As standards, specifications and designs change from time totime, please ask for confirmation of the information given in thispublication.

Publication: Communication BT-S2ECreated by: Sodipe (38)

Merlin GerinF-38050 Grenoble cedex 9tel. +33 (0)4 76 57 60 60telex : merge 320 842 F

Schneider Electric SA

03/00

M9F

P46

AE

N

DIT E D1 97 010 enART. 078255

This document has beenprinted on ecologicalpaper

SpecificationsElectrical specificationsc Power circuit:rating at 40°C: 16 to 100 A (AC7a category).c Control circuit:v operating voltage:- 24 V AC ± 10%- 230/240 V AC: -15% +6%,v coil frequency: 50 Hz.c Electrical endurance:v AC1 and AC7a categories:- 16 A ratings, 100,000 operations- 25 A ratings, 250,000 operations- 40-63-100 A ratings, 200,000 operations.Mechanical specificationsc Visualisation of contactor state on front panel(coil fed or manual operation).c Mechanical endurance: 1,000,000 operations.c Connections:v control circuit:- rigid cable: 2 x 1.5 mm2

- supple cable: 2 x 2.5 mm2,v power circuit:- rigid cable:6 mm2 up to 25 A25 mm2 for 40 and 63 A50 mm2 for 100 A- supple cable:2 x 2.5 mm2 up to 25 A2 x 10 mm2 for 40 and 63 A2 x 35 mm2 for 100 A.

Schematic diagrams

Approvals

1A1

A2 2

1A1

A2 2

3

4

1R1

2R2

A1

A2

R1

R2

A1

A2

R3

R4

Oauto

I P

1A1

A2 2

3

4

5

6

7

8Oauto

I P

1A1

A2 2

3

4

5

6

1A1

A2 2

3

4

5

6

7

8

1A1

A2 2

3

4

5

6

R1

R2

A1

A2

R3

R4

R5

R6

R7

R8

Oauto

I P

1A1

A2 2

3

4

1R1

2R2

A1

A2

3

4

R3

R4

Implementationc Designed to be installed in modular switchboxes and switchboards.c Optimised dimensions: in accordance with therating and number of poles.c Easy symmetrical rail mounting using a two-state latch.c Easy connection using grooved tunnelterminals with flap.c Mixed +/- socket screws which cannot be lost.c Auxiliaries simply clipped on to contactors.

Selection tablenumber power circuit width type of control referencesof poles rating voltage in mod. contacts circuit man. op. mech.

(A) (V AC) (9 mm) voltage (V AC) with without

1P 25 250 2 1C 230/240 15958

2P 16 250 2 1C+1O 230/240 15956

2 2C 230/240 1595725 250 2 2C 230/240 15981 15959

2 2C 24 16020

2 2O 230/240 1596040 250 4 2C 230/240 15984 15966

63 250 4 2C 230/240 15987 15971

4 2C 24 16024100 250 6 2C 230/240 15977

3P 25 400 4 3C 230/240 15982 15961

40 400 6 3C 230/240 1596763 400 6 3C 230/240 15972

4P 25 400 4 4C 230/240 15983 15962

4 4C 24 160224 4O 230/240 15963

4 4O 24 16023

4 2C+2O 230/240 1596440 400 6 4C 230/240 15986 15968

6 4O 230/240 15969

63 400 6 4C 230/240 15988 159736 4C 24 16025

6 4O 230/240 15974

6 4O 24 160266 2C+2O 230/240 15975

100 400 12 4C 230/240 15978

4-pole (4N/C)

EnvironmentEnvironmentc Tropicalisation:treatment 2 (relative humidity: 95% at 55°C ).c Protection class:IP 201 (front panel: IP 4).c Operating temperature:-5°C to +50°C.c Storage temperature:-40°C to +70°C.c Complies with the strictest regulations anddirectives in the area of «environmentalprotection».

4-pole (4C)manual op. mech.

3-pole (3C)manual op. mech.

2-pole (2C)manual op. mech.

4-pole (2C+2O)

4-pole (4O)4-pole (4C)3-pole (3C)

2-pole (2O)2-pole (2C)2-pole (1C+1O)1-pole (1C)

Schematic diagrams

Selection table

Approvals

Specifications

Implementation

As standards, specifications and designs change from time totime, please ask for confirmation of the information given in thispublication.

Publication: Communication BT-S2ECreated by: Sodipe (38)

Merlin GerinF-38050 Grenoble cedex 9tel. +33 (0)4 76 57 60 60telex : merge 320 842 F

Schneider Electric SA

03/00

M9F

P46

AE

N

DIT E D1 97 010 enART. 078255

This document has beenprinted on ecologicalpaper

SpecificationsElectrical specificationsc Power circuit:rating at 40°C: 16 to 100 A (AC7a category).c Control circuit:v operating voltage:- 24 V AC ± 10%- 230/240 V AC: -15% +6%,v coil frequency: 50 Hz.c Electrical endurance:v AC1 and AC7a categories:- 16 A ratings, 100,000 operations- 25 A ratings, 250,000 operations- 40-63-100 A ratings, 200,000 operations.Mechanical specificationsc Visualisation of contactor state on front panel(coil fed or manual operation).c Mechanical endurance: 1,000,000 operations.c Connections:v control circuit:- rigid cable: 2 x 1.5 mm2

- supple cable: 2 x 2.5 mm2,v power circuit:- rigid cable:6 mm2 up to 25 A25 mm2 for 40 and 63 A50 mm2 for 100 A- supple cable:2 x 2.5 mm2 up to 25 A2 x 10 mm2 for 40 and 63 A2 x 35 mm2 for 100 A.

Schematic diagrams

Approvals

1A1

A2 2

1A1

A2 2

3

4

1R1

2R2

A1

A2

R1

R2

A1

A2

R3

R4

Oauto

I P

1A1

A2 2

3

4

5

6

7

8Oauto

I P

1A1

A2 2

3

4

5

6

1A1

A2 2

3

4

5

6

7

8

1A1

A2 2

3

4

5

6

R1

R2

A1

A2

R3

R4

R5

R6

R7

R8

Oauto

I P

1A1

A2 2

3

4

1R1

2R2

A1

A2

3

4

R3

R4

Implementationc Designed to be installed in modular switchboxes and switchboards.c Optimised dimensions: in accordance with therating and number of poles.c Easy symmetrical rail mounting using a two-state latch.c Easy connection using grooved tunnelterminals with flap.c Mixed +/- socket screws which cannot be lost.c Auxiliaries simply clipped on to contactors.

Selection tablenumber power circuit width type of control referencesof poles rating voltage in mod. contacts circuit man. op. mech.

(A) (V AC) (9 mm) voltage (V AC) with without

1P 25 250 2 1C 230/240 15958

2P 16 250 2 1C+1O 230/240 15956

2 2C 230/240 1595725 250 2 2C 230/240 15981 15959

2 2C 24 16020

2 2O 230/240 1596040 250 4 2C 230/240 15984 15966

63 250 4 2C 230/240 15987 15971

4 2C 24 16024100 250 6 2C 230/240 15977

3P 25 400 4 3C 230/240 15982 15961

40 400 6 3C 230/240 1596763 400 6 3C 230/240 15972

4P 25 400 4 4C 230/240 15983 15962

4 4C 24 160224 4O 230/240 15963

4 4O 24 16023

4 2C+2O 230/240 1596440 400 6 4C 230/240 15986 15968

6 4O 230/240 15969

63 400 6 4C 230/240 15988 159736 4C 24 16025

6 4O 230/240 15974

6 4O 24 160266 2C+2O 230/240 15975

100 400 12 4C 230/240 15978

4-pole (2N/C+2N/O)

Owing to changes in standards and equipment, the characteristics given in the text and images in this document are not binding until they have been confirmed with us.

Type Rating (A)

Consumptioninrush (VA)

Holding (VA)

Max. power (W)

1P, 2P 16/25 15 3.8 1.1

3P, 4P 16/25 34 4.6 1.6

2P 40/63 34 4.6 1.6

3P, 4P 40/63 53 6.5 2.1

2P 100 53 6.5 2.1

4P 100 106 13 4.2

Customer Care Freecall 0800 652 999

www.schneider-electric.co.nz

Schneider Electric New Zealand Ltd