CRS DATA CENTRE CEILING SYSTEMS
Transcript of CRS DATA CENTRE CEILING SYSTEMS
C R S D A T A C E N T R E C E I L I N G S Y S T E M S
Complimenting our range of
data centre specific products
& services CRS manufactures
& installs structural grid ceiling
systems purpose developed
for mission critical data centre
environments.
Designed with flexibility,
customization & ease of install in
mind, CRS Ceiling Systems
are the optimal choice for
applications where complex and
concentrated overhead services
are required including lighting,
cable trays, fibre duct, fire
protection, and power busways.
CRS ceiling systems allow for
extremely rapid installation
times providing extensive
cost benefits over the more
traditional & cumbersome
structural ceiling systems.
Page 1 of 8
C R S D A T A C E N T R E C E I L I N G S Y S T E M S
The CRS ceiling grid is suspended from building structures above using threaded rod connected to a purpose built innovative bracket assembly that enables ceiling height trimming adjustments without the need for a traditional turnbuckle.
The adjustment spindle that inserts into the bracket enables the spindle height to be pre-set on the threaded rods so that the ceiling grid can be preassembled at the working floor plane and easily lifted in sectionsand attached to the suspension rods.
K E Y F E A T U R E SNo turnbuckle or reverse threaded rod sections are required.
Indexing notches located at fixed intervals on main grid extrusions for accurate location of connection brackets.
Grid extrusion incorporates an underside channel for the insertion of fastening nuts which provide exceptional pull out resistance and connection reliability for robust fixing to the ceiling.
Attachment of preassembled ceiling sections to threaded rods simplified with innovative bracket design that hooks onto rod spindle, ie no fiddly connection to turnbuckles.
Fasteners do not leave permanent paint damage to underside of channel improving aesthetics over life-cycle of ceiling.
A I R F L O W M A N A G E M E N T
Air flow delivery from or return to the plenum space can be provisioned for by the use of grilles that can be readily installed in the ceiling grid where required for instance above hot aisles.
Air grilles with adjustable opposed blade dampers are also available for applications where modulation of return air flow is required.
Page 2 of 8
All Sales Enquiries t: 1300 367 983 e: [email protected]
CRS Sydney - Head OfficeUnit C, 110 McEvoy Street Alexandria NSW 2015 t: 02 9469 1100 e: [email protected] w: www.crs.com.au
CRS MelbourneUnit 7, 28 Ricketts Road Mount Waverley VIC 3149 t: 03 9263 0400 e: [email protected] w: www.crs.com.au
CRS SingaporeFloor 11, Wisma Atria 435 Orchard Rd Singapore 238877t: +65 66 32 35 66 e: [email protected] w: www.crs.com.au
Page 3 of 8
C R S D A T A C E N T R E C E I L I N G S Y S T E M S
C R S D A T A C E N T R E C E I L I N G S Y S T E M S
T-Bolts drop through bracket feet then rotate and
seat into cross position.
Indexing Notches align with locating pins on
the bottom of the grid suspension bracket.
Adjustment spindle located on
threaded rod, inserts from side into
bracket body.
BRACKET BODY
ADJUSTMENT
SPINDLE
W W W. C R S . C O M . A UPage 4 of 8
C R S D A T A C E N T R E C E I L I N G S Y S T E M S
W W W. C R S . C O M . A U
A C C E S S O R I E S
Channel Nuts
C E I L I N G T I L E S
CRS ceiling tiles are made from
a single formed metal sheet
to an engineered profile that
enhances seal integrity and ready
access removal. All ceiling tiles
are manufactured from electro
gal or equivalent sheet metal
guaranteeing inherent corrosion
resistance and prevention of zinc
whiskers. Available in a range of
nominal pan sizes such as 1200 x
600mm to suit all common grid
configurations.
CRS also provide a range of base
sheet metal thickness including
0.7mm, 0.9mm and 1.2mm with
powder coated finish to align with
applicable differential pressures.
Perimeter seals can also be
provided where extremely high
containment integrity is required.
J O I N T S E A L I N G
CRS ceiling systems are sealed
against air leakage into the ceiling
plenum using a purpose designed
self-adhesive foam seal strip.
The foam strip is applied on all
perimeter sides of the ceiling
tile to ensure it seals effectively
into the ceiling grid. Tape will
overlap sufficiently at ends so that
adequate seal density is achieved
in corners.
T R I M M I N G
To ensure the effectiveness of the
ceiling across the full installation
area, grid framing and ceiling
tiles can be readily adpated as
necessary to ensure the ceiling
containment plane is preserved.
Careful design consideration has
been given to real world data
centre applications and as such
the CRS ceiling design allows
for seamless integration around
standard penetrations for the
following;
• Environmental sensors
• Annunciators
• Fire detection & suppression
systems
• Cable trays & managers
• Light fittings etc
Page 5 of 8
M6, M8, M10
Spring Clips
D I M E N S I O N S
SECTION A-ATYPICAL VIEW OF LONG SECTIONS
1:4
SECTION B-B TYPICAL VIEW OF SHORT SECTIONS
1:4
1200
1200
HEIGHT ADJUSTMENT SPINDLE NUTSPRING CLIP
M10 T-BOLT
M10 SERRATED FLANGE HEX NUT
AA
B
B
M10 ALLTHREAD RODGALVANISED
0.9 GALVANNEALCEILING TILE
TESA 601 FOAM SEALING TAPE
M10 ROLL IN CHANNEL NUT
HEIGHT ADJUSTINGSPINDLE NUT
M10 ALLTHREAD RODGALVANISED
RETAINER CLIP
E
F
ALLOY EXTRUSION300 KG/1.2 METRE LOAD RATINGPENDING ENGINEERS APPROVAL.
C R S D A T A C E N T R E C E I L I N G S Y S T E M S
P E R I M E T E R E X T R U S I O N S E C T I O N
S T A N D A R D E X T R U S I O N S E C T I O N
W W W. C R S . C O M . A UPage 6 of 8
ITEM DESCRIPTIONCLNG-AGE-PC-3600 Ceiling Aluminium Grid Extrusion Powder Coated (L) 3600mmCLNG-APE-PC-3600 Ceiling Aluminium Perimeter Extrusion Powder Coated (L) 3600mmCLNG-AGE-PC-1200 Ceiling Aluminium Grid Extrusion Powder Coated (L) 1200mmCLNG-TL-1200-600-PC Ceiling Tile 0.9mm Nom 1200mm x 600mm Powder CoatedRTNR-CLP-CT-AGE Retainer Clip For Ceiling Tile To Aluminium Grid ExtrusionHNGR-BKT-ACE Hanger Bracket For Aluminium Ceiling ExtrusionSPDL-NT-M10-30 Spindle Nut M10 X 30mm For Ceiling Hanger BracketRTNR-CLP-CHBSN Retainer Clip For Ceiling Hanger Bracket SpindleCHN-T-BLT-M10-30 Channel T Bolt M10 X 30mm Suits Aluminium CeilingWNM10 Serrated Flange (Whiz) Hex Nut M10CHN-NT-RLS-M10 Channel Nut With Roll Spring M10 For Aluminium CeilingCHN-NT-RLS-M8 Channel Nut With Roll Spring M8 For Aluminium CeilingCHN-NT-RLS-M6 Channel Nut With Roll Spring M6 For Aluminium CeilingCLNG-RAG-1200-600 Egg Crate Return Air Grille Nom 1200mm x 600mmCLNG-RAG-1200-600-AD
Egg Crate Return Air Grille Fitted With Ajustable Damper Nom 1200mm x 600mm
O R D E R I N G I N F O R M A T I O N
LOAD CAPACITY
Attachment Location General Grid(Based on 1200mm x 1200mm
suspension centres)
Channel Nut Below Bracket
Point Load (kN) 2.0 kN 4.9kN 4.9 kN
Uniform Load (k/N/m2) 2.8 kPa - -
Ultimate Point Load (kN)
3.6 kN 6.6 kN 6.6 kN
L O A D R A T I N G S
C R S D A T A C E N T R E C E I L I N G S Y S T E M S
W W W. C R S . C O M . A UPage 7 of 8
All Sales Enquiries t: 1300 367 983 e: [email protected]
CRS Sydney - Head OfficeUnit C, 110 McEvoy Street Alexandria NSW 2015 t: 02 9469 1100 e: [email protected] w: www.crs.com.au
CRS MelbourneUnit 7, 28 Ricketts Road Mount Waverley VIC 3149 t: 03 9263 0400 e: [email protected] w: www.crs.com.au
CRS SingaporeFloor 11, Wisma Atria 435 Orchard Rd Singapore 238877t: +65 66 32 35 66 e: [email protected] w: www.crs.com.au
Page 8 of 8