Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

21
Page 1 Course 4, Module 7: Electro-Optic and Acousto-Optic Devices 8.12.2010 15:10:39 http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm This version reflects the comments of the core participants as reviewed and incorporated in accordance with CORD's FIPSE-supported Curriculum Morphing Project. MODULE 4-7 ELECTRO-OPTIC AND ACOUSTO-OPTIC DEVICES General Comments of John Simcik lectro-optic and acousto-optic devices are used with lasers as Q-switches, beam deflectors, modulators, and mode-lockers. The electro-optic effect is a change in the index of refraction for certain crystals as a function of applied voltage. The index change is dependent on the direction and polarization of the incident beam. The acousto-optic effect involves an interaction between sound waves and light waves traveling through other types of crystals. The acousto-optic effect can be used to control the frequency, intensity, and direction of an optical beam. When you complete this unit, you will be able to: 1. Describe the operation of electro-optic devices and give a list of potential applications. 2. Define extinction ratio as it applies to an electro-optic modulator. 3. Given the relevant parameters, calculate the transmission of an electro-optic modulator. 4. Define the difference in operation for an electro-optic modulator operated in the longitudinal and transverse modes. Draw a diagram illustrating each configuration. Compare the characteristics of each mode. 5. Describe the operation of acousto-optic devices and give a list of potential applications. 6. Draw and label a block diagram of a simple acousto-optic beam-deflection system. 7. State the equation for the rise time for an acousto-optic modulator as a function of laser beam diameter. Calculate and plot the rise time as a function of the diameter for a ? ? en acoustic velocity. 8. Given the necessary parameters, calculate the deflection angle for an acousto-optic light-beam deflector. 9. Compare the speed and number of resolvable spots for electro-optic and acousto-optic light-beam deflectors. Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Transcript of Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 1: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 1Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

This version reflects the comments of the core participants as reviewed and incorporated in accordance withCORD's FIPSE-supported Curriculum Morphing Project.

MODULE 4-7

ELECTRO-OPTIC ANDACOUSTO-OPTIC DEVICES

General Comments of John Simcik

lectro-optic and acousto-optic devices are used with lasers as Q-switches, beam deflectors,modulators, and mode-lockers. The electro-optic effect is a change in the index of refraction forcertain crystals as a function of applied voltage. The index change is dependent on the direction andpolarization of the incident beam. The acousto-optic effect involves an interaction between soundwaves and light waves traveling through other types of crystals. The acousto-optic effect can be usedto control the frequency, intensity, and direction of an optical beam.

When you complete this unit, you will be able to:

1. Describe the operation of electro-optic devices and give a list of potential applications.

2. Define extinction ratio as it applies to an electro-optic modulator.

3. Given the relevant parameters, calculate the transmission of an electro-optic modulator.

4. Define the difference in operation for an electro-optic modulator operated in the longitudinal andtransverse modes. Draw a diagram illustrating each configuration. Compare the characteristics ofeach mode.

5. Describe the operation of acousto-optic devices and give a list of potential applications.

6. Draw and label a block diagram of a simple acousto-optic beam-deflection system.

7. State the equation for the rise time for an acousto-optic modulator as a function of laser beamdiameter. Calculate and plot the rise time as a function of the diameter for a ?�?��enacoustic velocity.

8. Given the necessary parameters, calculate the deflection angle for an acousto-optic light-beamdeflector.

9. Compare the speed and number of resolvable spots for electro-optic and acousto-optic light-beamdeflectors.

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 2: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 2Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

10. Use an electro-optic modulator to modulate a beam of laser light. Measure the half-wavevoltage, the extinction ratio, and the modulation frequency. From the measured values, calculate thebirefringence as a function of applied voltage.

11. Set up and operate an acousto-optic beam deflector. Adjust the drive frequency of the deflectorand measure the deflection of a laser beam.

Electro -Optic Modulators

In this section, we discuss the operation and application of electro-optic devices that rely on thephenomenon of birefringence that is induced by application of voltage to a crystal. Let us firstdefine birefringence. In certain crystalline materials, an incident light ray will separate into two raysthat may travel in different directions. These crystals are called birefringent. The direction in whichthe light travels is dependent on its polarization. For each of the two different perpendicular statesof polarization, the light will travel in a different direction. Birefringence is also called doublerefraction because when the light enters the crystal, it is refracted into two different directions.

Figure 1 shows the effect of birefringence when a beam of unpolarized light enters the surface of abirefringent material at an angle q to the normal to the surface. The two different components ofpolarization (horizontal and vertical) travel in two different directions. The material has twodifferent indices of refraction, one for each of the two perpendicular components of polarization. Inaccordance with the laws of geometric optics, the two rays are refracted at different angles as theyenter the crystal.

Fig. 1Schematic diagram showing the separation of the two

components of polarization in a light beam traveling through abirefringent material. The incident light is unpolarized.

Many crystalline materials exhibit birefringence naturally, without application of any voltage. Thebirefringence is present all the time. Examples of such crystals are quartz and calcite.

There are also a number of crystals that are not birefringent naturally but in which application of avoltage induces birefringence. This phenomenon is called the electro-optic effect. The electro-opticeffect leads to the ability to control light beams in a variety of ways and is the basis of a number ofapplications, including light-beam modulators, Q-switches, and deflectors. Examples of crystals thatexhibit the electro-optic effect are potassium dihydrogen phosphate (commonly called KDP),ammonium dihydrogen phosphate (ADP), potassium dideuterium phosphate (KD*P), lithiumniobate, and barium sodium niobate.

The operation of an electro-optic device used as a light-beam modulator is shown schematically inFigure 2. Polarized light is incident on the modulator. The light may be polarized originally or a

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 3: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 3Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

polarizer may be inserted, as shown. The analyzer, oriented at 90?�to the polarizer, prevents anylight from being transmitted when no voltage is applied to the electro-optic material. When thecorrect voltage is applied to the device, the direction of the polarization is rotated by 90?�. Then thelight will pass through the analyzer.

Fig. 2Schematic diagram of the operation of a modulator based

on the electro-optic effect. In this configuration, the voltage isapplied parallel to the direction of light propagation.

Two types of electro-optic effect have been used: the Kerr electro-optic effect, which is shown byliquids such as nitrobenzene, and the Pockels electro-optic effect, shown by crystalline materialssuch as ammonium dihydrogen phosphate or lithium niobate. Some early electro-optic devices usednitrobenzene, but the liquid tends to polymerize in the presence of the intense laser light. Modernelectro-optic modulators use the Pockels effect. The electro-optic modulators are often calledPockels cells.

The orientation of the polarizer and analyzer at 45?�to the vertical, as shown in Figure 1, is acommon configuration, used with many commercial modulators. But the orientation depends on theparticular material used and on the direction in which the crystal has been cut. The manufacturer’sinstructions should be consulted to ensure proper orientation of the modulator and the directions ofthe pass axes for the polarizer and analyzer.

With the direction of polarization at 45?�to the vertical direction, the polarization vector iscomposed of two perpendicular components of equal intensity, one vertical and one horizontal. Thecrystalline element is oriented with its axes in a specified orientation (which depends on thecrystalline symmetry of the particular material). The applied voltage induces birefringence in thecrystal, so that the two components of polarization travel with different velocities inside the crystal.This induced birefringence is the basis of the electro-optic effect.

The two components travel in the same direction through the crystal and do not become physicallyseparated. But the two components, in phase as they enter the crystal, emerge with different phases.As they traverse the crystal, they accumulate a phase difference, which depends on the distancetraveled and on the applied voltage. When the beams emerge from the crystal, the polarization ofthe combined single beam depends on the accumulated phase difference. If the phase difference isone-half wavelength, the polarization is rotated by 90?�from its original direction. This by itselfdoes not change the intensity of the beam. But, with the analyzer, the transmission of the entiresystem varies, according to

T = T0 sin2(p D nL/l ) Equation 1

where T is the transmission, T0 the intrinsic transmission of the assembly, taking into account all thelosses, D n the birefringence (that is, the difference in refractive index for the two polarizations), Lthe length of the crystal, and l the wavelength of the light. The birefringence is an increasingfunction of the applied voltage, so that the transmission of the device will be an oscillatory functionof applied voltage. The maximum transmission occurs when

D n = l /2L Equation 2

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 4: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 4Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

This occurs at a voltage called the half-wave voltage, denoted V1/2. The half-wave voltage dependson the nature of the electro-optic material. The half-wave voltage for a particular material increaseswith the wavelength. Thus, in the infrared the required voltage is higher than in the visible. Thisfactor can limit the application of electro-optic modulators in the infrared.

The transmission of an electro-optic device as a function of applied voltage is shown in Figure 3,indicating the maximum transmission at the half-wave voltage.

Fig. 3Transmission of an electro-optic device as a function of applied voltage.

V1/2 denotes the half-wave voltage.

In most crystals, each of the prominent crystalline faces belongs to one of three families of planesthat intersect along what are called crystal axes. These axes can be designated as coordinate axes,even though they are not generally at right angles to each other. When one fabricates an electro-optic modulator, the crystal must be cut at certain specified angles to the crystalline axes. A fulldiscussion of the different orientations and the reasons for them is beyond the scope of this module.We simply note that different crystalline symmetries require that specific relations be maintainedbetween the crystalline axes and the faces of the electro-optic element.

One important performance parameter for electro-optic modulators is the extinction ratio, defined asthe ratio of the transmission when the device is fully open, to the transmission when the device isfully closed. In practice there is always some light leakage, so the minimum transmission neverreaches zero. A high value of the extinction ratio is desirable because it determines the maximumcontrast that may be obtained in a system that uses the modulator. Commercial electro-opticmodulators can have extinction ratios in excess of 1000.

Electro-optic modulators may be fabricated with different physical forms. In one form, voltage isapplied parallel to the light propagation, as was shown in Figure 2. One uses transparent electrodesor electrodes with central apertures. This is called a longitudinal electro-optic modulator.

In another form, metal electrodes are on the sides of the crystal (which has a square cross section)and the voltage is perpendicular to the light propagation. This is called a transverse modulator. Twoexamples are shown in Figure 4. The top is a two-element configuration suitable for use withmaterials like ADP. The use of two crystals oriented as shown provides compensation for thenatural birefringence of the material. The bottom portion of the figure shows a single-elementconfiguration suitable for lithium tantalate-type materials. Both single- and dual-elementconfigurations are in use in commercial modulators.

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 5: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 5Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

Fig. 4Transverse electro-optic modulator configurations.

Top: Two-element configuration suitable for ADP-type materials.Bottom: Single-element configuration suitable for lithium tantalate-type materials

Longitudinal and transverse modulators have different applications. Longitudinal modulators mayhave large apertures, but the half-wave voltage will be high, often in the kilovolt range.Longitudinal modulators are often used with conventional light sources. Because it is difficult tovary the required high voltages rapidly, the frequency response of longitudinal modulators tends tobe low. Applications for which longitudinal modulators are suited include relatively low-frequencymodulation of laser beams or use with non-laser sources.

In transverse modulators, the voltage is applied perpendicular to the light propagation. The phaseretardation for a given applied voltage may be increased simply by making the crystal longer. Thehalf-wave voltage thus may be much lower for transverse modulators, perhaps as low as 100 volts.It follows that the frequency response may be much higher. Transverse modulators are thus suitedfor fast, broadband applications. A problem with transverse modulators is the relatively smallaperture that they permit, because the crystal may be a long, thin parallelepiped. This physicalconfiguration means that transverse modulators are best suited for use with narrow, well-definedlaser beams. In addition, the extinction ratios available with transverse modulators tend to be lowerthan for longitudinal modulators. Applications of transverse modulators include broadband opticalcommunication, display and printing systems, and fast image and signal recorders.

Table 1 lists electro-optic materials and some of their characteristics. The table includes the namesof a number of electro-optic materials, their common abbreviations, their chemical formulas, andthe spectral range over which they are transmissive. The bandwidths quoted are for use of thematerials in commercially available electro-optic light modulators. Most of the materials are suitedfor use in the visible and near-infrared portions of the spectrum, but cadmium telluride is useful as amodulator for CO2 lasers in the long-wavelength infrared.

Of the materials in the table, ADP, AD*P, and KD*P are relatively older materials. They may beused as either longitudinal or transverse modulator materials, but have relatively high half-wavevoltages.

Lithium niobate and lithium tantalate represent a relatively modern class of electro-optic materials,which have larger electro-optic effects and smaller half-wave voltages. They are hard to grow inlarge crystals of high quality but they are perhaps the best available modern electro-optic materials.

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 6: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 6Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

Table 1. Electro-Optic Materials

Material Abbreviation ChemicalFormula

TransmissionRange(µ M)

Bandwidth(MHz)

Index ofRefraction

no,ne atwavelength

(µm)

Ammoniumdihydrogenphosphate

ADP NH4H2PO4 0.3 - 1.2 to500

1.51, 1.47at 1.06

Potassiumdihydrogenphosphate

KDP KH2PO4 0.25 - 1.7 >100

1.51, 1.47at 0.55

Potassiumdideuteriumphosphate

KD*P KD2PO4 0.3 - 1.1 to350

1.49, 1.46at 1.06

Lithiumniobate LN LiNbO3 0.5 - 2 to

80002.23, 2.16

at 1.06

Lithiumtantalate — LiTaO3 0.4 - 1.1 to 1000

2.14,2.143at 1.00

Cadmiumtelluride — CdTe 2 - 16 to 1000

no = 2.6at 10

The speed of electro-optic modulators is expressed as a bandwidth, i.e., the rate at which the devicecan be turned on and off. The bandwidth of electro-optic modulators can be very large, up tohundreds of megahertz. The speed is limited mainly by the ability to produce voltage pulses ofsufficient amplitude at high frequency.

We summarize some of the advantages and drawbacks of electro-optic devices as light-beammodulators. Electro-optic modulators have higher speed and larger bandwidth than competingtechnologies (mechanical and acousto-optic devices). Electro-optic devices have some limitations,including their relatively high voltage requirements and limited beam-diameter capabilities.

Acousto-Optic Modulators

A different approach to modulator technology uses the interaction between light and sound waves toproduce changes in optical intensity, phase, frequency, and direction of propagation. Acousto-opticmodulators are based on the diffraction of light by a column of sound in a suitable interactionmedium.

When a sound wave travels through a transparent material, it causes periodic variations of the indexof refraction. The sound wave can be considered as a series of compressions and rarefactionsmoving through the material. In regions where the sound pressure is high, the material iscompressed slightly. This compression leads to an increase in the index of refraction. The increaseis small, but it can produce large cumulative effects on a light wave passing some distance throughthe compressed material.

An acousto-optic device requires a material with good acoustic and optical properties and highoptical transmission. Several types of material are available. We shall describe acoustic-opticmaterials in more detail later.

The sound wave is produced by a piezoelectric transducer. Piezoelectric materials exhibit slightchanges in physical size when voltage is applied to them. An example of one such material iscrystalline quartz. If the piezoelectric material is placed in contact with the acousto-optic materialand a high-frequency oscillating voltage is applied to the piezoelectric material, it will expand and

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 7: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 7Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

contract as the voltage varies. This in turn exerts pressure on the acousto-optic material and willlaunch an acoustic wave (sound wave) which will travel through the material. The frequency F ofthe acoustic wave will be the same as the frequency of the applied voltage. The acoustic wave willhave a wavelength Λ given by:

FΛ = C Equation 3

where C is the velocity of sound in the material, typically of the order of 105 cm/sec. Variation ofthe acoustic frequency of the driver will thus change the acoustic wavelength, which in turn changesthe characteristics of the acousto-optic interaction.

A typical structure for an acousto-optic device is shown in Figure 5. The piezoelectric materials andmetal layers are bonded or deposited on the acousto-optic material. A radio-frequency field isapplied across the piezoelectric material using the metal layers as electrodes. The acoustic wave isthen launched into the acousto-optic medium by the piezoelectric material. Acoustic wavespropagating from a flat piezoelectric transducer into a crystal will form almost plane wavefrontstraveling in the crystal. The opposite end of the material from the transducer should have anacoustic termination to suppress reflected acoustic waves.

Fig. 5Typical structure of an acousto-optic device

The elasto-optic properties of the medium respond to the acoustic wave so as to produce a periodicvariation of the index of refraction. A light beam incident on this disturbance is partially deflected inmuch the same way that light is deflected by a diffraction grating. The operation is shown in Figure6. The alternate compressions and rarefactions associated with the sound wave form a grating thatdiffracts the incident light beam. No light is deflected unless the sightsst wave is present.

Fig. 6Diagram showing the principles of operation of an acousto-optic light-beam modulator or deflector.

The diagram defines the Bragg angle F and deflection angle F used in the text.

For a material with a fixed acoustic velocity, the acoustic wavelength or grating spacing is afunction of the radio-frequency drive signal; the acoustic wavelength controls the angle of

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 8: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 8Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

deflection. The amplitude of the disturbance, a function of the radio-frequency power applied to thetransducer, controls the fraction of the light that is deflected. Thus, the power to the transducercontrols the intensity of the deflected light. Modulation of the light beam is achieved by maintaininga constant radio frequency, allowing only the deflected beam to emerge from the modulator andmodulating the power to the transducer. Thus the modulator will be in its off state when no acousticpower is applied and will be switched to its transmissive state by the presence of acoustic power.

The transmission T of an acousto-optic modulator is

T = T0 sin2(p (M2PL/2H)0.5/l cos Q ) Equation 4

where P is the acoustic power supplied to the medium, l is the wavelength, L is the length of themedium (length of the region in which the light wave interacts with the acoustic wave), H is thewidth of the medium (width across which the sound wave travels), and the inherent transmission T0is a function of reflective and absorptive losses in the device. The quantity M2 is a figure of merit, amaterial parameter that indicates the suitability of a particular material for this application. It isdefined by

M2 = n6p2/r v3 Equation 5

where p is the photoelastic constant of the material, r is its density, and v is the velocity of sound inthe material. This figure of merit relates the diffraction efficiency to the acoustic power for a givendevice. It is useful for specifying materials to yield high efficiency, but in practical devices,bandwidth is also important, so that specifying a high value of M2 alone is not sufficient.

The angle Q is the so-called Bragg angle. The diffraction of the light beam by the periodic array ofacoustic waves satisfies the same relationship as the scattering of X rays by periodic planes of atoms(so-called Bragg scattering). Hence the diffraction of the light waves is also referred to as Braggreflection. Bragg reflection of X rays occurs at the planes of atoms in a crystal which are spaced aregular distance apart. The so-called Bragg angle gives the angle at which the most efficientreflection occurs. The phenomenon of optical reflection from the regular wavefronts of the acousticwaves is exactly the same, with the provision that the acoustic wavelength replaces the distancebetween planes of atoms.

The Bragg angle Q is defined as the angle the beam makes with the reflecting waves. It is given by:

sin Q = l /2nΛ Equation 6

where n is the index of refraction of the material, λis the optical wavelength and Λ is the acousticwavelength.

To use the acousto-optic device as a modulator, one should employ the deflected beam as shown inFigure 7. This will give higher values of the extinction ratio than using the undeflected beam. Whenthe acoustic drive is off, the light in the direction of the deflected beam is zero. When the acousticdrive is on, light is diffracted into that direction. Thus, the acousto-optic device controls the light inthat direction, turning it on and off at will. The device is operated as a modulator by keeping theacoustic wavelength (frequency) fixed and varying the drive power to vary the amount of light in thedeflected beam. As we shall see later, the use as a light-beam deflector is somewhat different.

Fig. 7Use of an acousto-optic device as a light-beam modulator

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 9: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 9Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

The design and performance of acousto-optic beam modulators have several limitations. Thetransducer and acousto-optic medium must be carefully designed to provide maximum light intensityin a single diffracted beam, when the modulator is in an open condition. The transit time of theacoustic beam across the diameter of the light beam imposes a limitation on the rise time of theswitching and therefore limits the modulation bandwidth. The acoustic wave travels with a finitevelocity and the light beam cannot be switched fully on or fully off until the acoustic wave hastraveled all the way across the light beam. Therefore, to increase bandwidth, one focuses the lightbeam to a small diameter at the position of the interaction so as to minimize the transit time.Frequently the diameter to which the beam may be focused is the ultimate limitation for thebandwidth. If the laser beam has high power, it cannot be focused in the acousto-optic mediumwithout damage.

General Comments of John Simcik

The rise time tr for an acousto-optic modulator is given by the equation:

tr = d/C Equation 7

where d is the diameter of the laser beam in the region of the interaction and C is the velocity ofsound in the material. As an example, for a tellurium dioxide acousto-optic modulator, with anacoustic velocity of 8.03 ?�105 cm/sec and a laser-beam diameter of 100 m m, the rise time is 0.01cm/8.03 ?�105 cm/sec = 1.245 ?�10- 8 = 12.45 nsec. Thus acousto-optic devices are capable ofhigh-frequency modulation.

Acousto-optic light-beam modulators have a number of important desirable features. The electricalpower required to excite the acoustic wave may be small, less than one watt in some cases. Highextinction ratios are obtained easily because no light emerges in the direction of the diffracted beamwhen the device is off. A large fraction, up to 90% for some commercial models, of the incidentlight may be diffracted into the transmitted beam. Acousto-optic devices may be compact and mayoffer an advantage for systems where size and weight are important. As compared to electro-opticmodulators, they tend to have lower bandwidth, but do not require high voltage.

Table 2 presents the characteristics of some materials used in commercially available acousto-opticmodulators. Several materials are available for use in the visible and near-infrared regions, and onematerial (germanium) is useful in the far infrared. The table also presents some values for the figureof merit M2, at a wavelength of 633 nm, except for GaAs (1530 nm) and Ge (10.6 mm). The factorsthat enter into the definition of M2 vary with crystalline orientation; the values in the table are forcrystals oriented to maximize M2. The values for bandwidth and for typical drive power arerepresentative of commercially available acousto-optic devices.

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 10: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 10Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

Table 2. Acousto-Optic Materials

Material Chemicalformula

Spectralrange(m m)

Figureof

meritM2(10-

15 m2/W)

Bandwidth(MHz)

Typicaldrivepower(W)

IndexofRefraction

AcousticVelocity(m/sec)

Fusedsilica/quartz

SiO20.3 -1.5 1.6 to 20 6 1.46

(6343 nm) 5900

Galliumarsenide GaAs 1.0 - 11 104 to 350 1 3.37

(1.15 µm) 5340

Galliumphosphide GaP 0.59 -

1.0 45 to 1000 50 3.31(1.15 µm) 6320

Germanium Ge 2.5 - 15 840 to 5 50 4.0(10.6 µm) 5500

Leadmolybdate

PbMoO40.4 -1.2 50 to 50 1 - 2 2.26

(633 nm) 3630

Telluriumdioxide

TeO2 0.4 - 5 35 to 300 1 - 2 2.26(633 nm) 4200

Lithiumniobate

L6Nb03 0.5-2 7 > 300 50-100 2.20(633nm) 6570

Light -Beam Deflectors

Light-beam deflectors, sometimes called scanners, form an important class of accessory that isrequired for applications such as display optical processing and optical data storage. Three mainmethods of light-beam deflection are commonly used: mechanical (i.e., galvanometer-type), electro-optic, and acousto-optic. The capabilities of these three types of systems are compared in Figure 8.Light-beam deflection is measured in terms of "resolvable spots," rather than in terms of theabsolute angle of deflection. One resolvable spot means that the beam is deflected by an angle equalto its own angular spread. The access time is the random-access time to acquire one specific spot orresolution element. The figure indicates that mechanical methods give the largest number ofresolvable spots, but are slowest, whereas electro-optic devices are fastest, but have the smallestnumber of resolvable spots. The figure characterizes the speed in terms of random access time toreach any desired spot. This is a useful parameter for applications like a random-access memory.Another possible method of characterizing speed would be the spot scan rate during a sequentialscan. This would be useful for applications like imaging or projection display. Again the mechanicalsystems are slowest and the electro-optic fastest, but the difference is less pronounced than for therandom-access time. We shall now describe the electro-optic and acousto-optic methods in moredetail.

Fig. 8Tradeoff between capacity (number of resolvable spots) and

access time for various types of light-beam deflectors

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 11: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 11Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

Electro-optic deflectors use prisms of electro-optic crystals like lithium niobate. A voltage is appliedto the crystal and changes the index of refraction of the material, and hence the direction ofpropagation of the beam traveling through the prism. Figure 9 illustrates the operation of such adevice.

Fig. 9Prism setup for an electro-optic light-beam deflector element. In the figure, n is

the index of refraction of the material and F is the angle of deflection.The figure defines the widths La and Lb used in the text.

The deflection angle for a plane wave passing through such a prism is obtained by applying Snell’slaw at the boundaries of the prism. The number N of resolvable spots is

N = D n(La - Lb)/e l Equation 8

where D n is the change in the index of refraction, which is a function of the applied voltage, Laand Lb are the widths defined in Figure 9, e is a factor of the order of unity, and l is the wavelength.

A method of construction for a useful beam deflector is shown in Figure 10. This uses two prisms,one with a positive value of D n and one with a negative value, when voltage is applied to theelectrodes as shown.

Fig. 10A possible construction for an electro-optic light-beam deflector, using

two prisms, one of which has a positive value of D n and the otherof which has a negative value

Electro-optic deflectors exhibit very fast response and short access time, but have relatively smallnumbers of resolvable spots, as Figure 8 showed. Other limitations are limited availability ofelectro-optic crystals with high optical quality throughout a sufficiently large volume, and relativelyhigh requirements on operating power. Because of these factors, electro-optic deflectors are usedless frequently than galvanometers, rotating mirrors, or acousto-optic devices. Most of the workdone on electro-optic deflectors has been experimental; relatively few commercial models areavailable.

Acoustic waves propagating from a flat piezoelectric transducer into a crystal form almost planarwavefronts in the crystal. Light rays passing through the crystal approximately parallel to theacoustic wavefronts are diffracted by the phase grating formed by the acoustic waves. Thediffraction satisfies the Bragg condition, similar to the diffraction of X rays from planes of atoms ina crystalline lattice. The Bragg angle has been defined above in equation 6.

The operation of acousto-optic devices has been illustrated in Figure 6 in connection with acousto-optic modulators. When an acousto-optic device is used as a modulator, one observes the diffracted

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 12: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 12Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

beam at a fixed angle and varies the acoustic power to change the diffraction efficiency. When oneuses an acousto-optic device as a deflector, one keeps the acoustic power constant but varies theacoustic wavelength so as to change the Bragg angle. Then F , the angle formed by the undiffractedand diffracted beams, is

equation9.jpg ( Equation 9

where l is the optical wavelength and Landais the acoustic wavelength. Note that this result is in radianmeasure. Changing Landathus changes the angle at which the beam emerges from the device. Becausethe acoustic wavelength is much longer than the optical wavelength, the absolute value of thedeflection angle is small, often a few milliradians.

The operation of an acousto-optic device as a light-beam deflector is illustrated in Figure 11. Thedrive power is kept constant and the acoustic wavelength (frequency) is varied, to deflect the beamto different angular positions. This is different from the way the device is used as a modulator(Figure 8).

Fig. 11Application of an acousto-optic device as a light-beam deflector

The bandwidth is limited by the time it takes for the acoustic wave to propagate across the diameterof the light beam, the same limitation that applies to the acousto-optic modulator. Acousto-opticdeflectors offer several advantages:

• easy control of deflection modes and position

• simple structure

• wide variety of uses from a single deflector

• larger number of resolvable spots than electro-optic devices

• faster access than mechanical devices

The capabilities of acousto-optic deflectors have been shown in Figure 8. Commercial models offerup to 1000 resolvable spots, with access times typically in the range of 5-50 microseconds. Two-dimensional deflection may be obtained by using two deflectors in series, with their directions ofdeflection at right angles. Acousto-optic deflectors have been employed in applications such ashigh-frequency scanning and optical signal processing. A variety of different types of Q-switch hasbeen developed. As we describe them, we shall use a solid-state laser as an illustration, but the basicmethods are applicable for other types of lasers also.

Q-Switches

Q-switching methods all employ a variable attenuator between the laser rod and the output mirror.During the time the rod is being pumped to a highly excited state, the attenuator is opaque and laseraction is inhibited. When the attenuator is suddenly switched to a transparent condition, the laser rodcan "see" the output mirror. The energy stored in the rod can be extracted by the stimulated-emission process and emitted through the output mirror in a short, high-power pulse.

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 13: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 13Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

The various types of attenuator that can be used define three other classes of Q-switch. The threetypes of variable attenuator that have been used most widely are electro-optic elements, acousto-optic elements, and bleachable dyes. Bleachable dyes, although least expensive, tend to openirregularly so that, for the highest performance, electro-optic or acousto-optic Q-switches arepreferred.

The use of electro-optic and acousto-optic elements as light modulators has been described earlier.It is apparent that a Q-switch is a specialized type of modulator. The operation of an electro-opticQ-switch for a solid-state laser is shown schematically in Figure 12. The solid-state crystal is ruby,because when the ruby rod is oriented as shown, the light emitted from the rod is polarized in ahorizontal direction. The analyzer will prevent the light from reaching the output mirror. Whenvoltage is applied to the electro-optic switch, the plane of polarization of the light is rotated 90?�.Then light from the rod passes through the analyzer and reaches the mirror. Electro-optic Q-switches use the Pockels effect in crystalline materials like potassium dideuterium phosphate. Theyare extremely fast, with opening times around one nanosecond. They are used most often at shorterwavelengths, in the visible spectrum, because the half-wave voltage increases at longer wavelengths.

Fig. 12Application of an electro-optic Q-switch

in a solid-state laser

Acousto-optic Q-switches rely on the diffraction grating set up by sound waves in certain materials,as described earlier. The light beam is deflected from its path by diffraction when the sound wave ispresent. The operation of an acousto-optic Q-switch is shown in Figure 13. When the acoustic waveis present, some of the light is diffracted and misses the mirror. The deflection angle, a smallfraction of one degree, is exaggerated in the figure. The loss due to diffraction is enough to keep thelaser below threshold. When the pumping of the laser is complete, the acoustic wave is switchedoff. Then all the light reaches the mirror and a laser pulse builds up rapidly. The most commonlyencountered acoustic Q-switch uses fused silica. The opening time is typically around 100nanoseconds, longer than for the electro-optic device.

General Comments of John Simcik

Fig. 13Application of an acousto-optic Q-switch in a solid-state laser

Acousto-optic devices have proved to be the most useful type for Nd:YAG lasers. The voltagerequired for operation of an electro-optic device increases with wavelength, a disadvantage forinfrared applications. Bleachable dyes for Q-switching in the infrared are less developed than thosefor use in the visible. Thus acousto-optic devices are most useful for Nd:YAG Q-switching.

Mode-Lockers

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 14: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 14Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

Within a Q-switched laser pulse there may be further substructure. This arises because of aphenomenon called mode-locking. If a number of longitudinal modes is present in the laser output,these modes may interfere and lead to an oscillatory behavior for the output. Thus, within theenvelope of the Q-switched pulse, there may be a train of shorter pulses. If only a single longitudinalmode is present in the laser output, there will be opportunity for mode-locking.

In many lasers, a number of longitudinal modes will be present simultaneously. Ordinarily, thephases of these modes will be independent of each other. But under some conditions, the modes caninteract with each other and their phases can become locked together. Then the behavior of theoutput will contain a train of short, closely spaced pulses within the Q-switched pulse.

Mode-locking may be accomplished intentionally by introducing a variable loss into the cavity, suchas an electro-optic or acousto-optic modulator, so that the gain of the cavity is modulated at thefrequency c/2L, which is the difference in frequency between adjacent longitudinal modes. Here c isthe velocity of light and L is the length of the laser cavity.

In the time domain, the output of the mode-locked laser consists of a series of very short pulses.From a simple point of view, one may consider that there is a very short pulse of light bouncingback and forth between the laser mirrors. Each time the pulse reaches the output mirror, a mode-locked pulse emerges from the laser. The result is a series of short pulses separated in time by 2L/c,the round-trip transit time of the cavity. The duration of these pulses is very short, often of the orderof a few picoseconds. Hence, a laser operating in this fashion is often called a picosecond pulselaser.

The mode-locking behavior is encouraged by inserting a modulator in the laser cavity near theoutput mirror and opening the modulator at a frequency c/2L. This is shown in Figure 14.

Fig. 14Example of a modulator used as a mode-locker

The minimum duration for a mode-locked pulse is equal to D n , where D n is the spectral width ofthe active medium. For an Nd:glass laser, the spectral width is large, around 1012 Hz. The minimumpulse duration for such a laser is then around 1 picosecond. The shortest pulses that have beenproduced have come from liquid-dye lasers, for which the spectral width can be very large. Pulsesas short as 30 femtoseconds (30 ?�10- 15 sec) have been produced. This is remarkable in that thetotal duration of the pulse contains only a few cycles of the high-frequency electric field.

One may obtain a single pulse with this duration by using an output coupler such as an electro-opticswitch that opens long enough to let one pulse emerge from the train of output pulses and thencloses again.

Drivers for Electro -Optic Devices

Electro-optic devices require relatively high voltages, typically of the order of kilovolts forlongitudinal devices and a hundred volts to a few hundred volts for transverse devices. The powersupplies that are used to supply them may be ordinary laboratory power supplies if the frequenciesare not too high. Any power supply or function generator that can supply the required half-wavevoltage at the required frequency will generally be adequate.

The Pockels cell represents a capacitive load, so the power dissipation is not excessively high.

If the frequency is high or a very rapid rise time is required, it becomes more difficult to switch therequired values of voltage at high speed. One circuit that has been employed for driving Pockels cell

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 15: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 15Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

modulators at high speed is shown in Figure 15. This circuit uses a switching tube called a krytron.This is a gas-filled tube that has the capability of shorting out voltages in the 3- to 7-kilovolt range.The trigger pulse that initiates the operation of the switch is delivered through a silicon-controlledrectifier (SCR) and transformer. This circuit is capable of switching the Pockels cell modulator atspeeds in the nanosecond range. The chief drawback of the circuit is the limited lifetime of the tube.

Fig. 15. Drive circuit for electro-optic Pockels cell

The manufacturers of commercial electro-optic light-beam modulators, deflectors, and Q-switchesgenerally also supply a line of power supplies for their devices. The voltages and impedances ofparticular power supplies are matched to the requirements of individual electro-optic devices. Therise times for some of these voltage drivers may be less than one nanosecond.

Drivers for Acousto-Optic Devices

The drive circuit for an acousto-optic device may be an electrical signal generator that delivers aperiodic voltage to the electrodes attached to the piezoelectric material bonded to the acousto-opticdevice. A simple radio-frequency generator may suffice. The generation of the acoustic waves doesdissipate power, so some drive power is necessary. Usually a few watts is sufficient.

Figure 16 shows how the drive power affects the performance of a commercial acousto-opticdevice. The figure shows the diffraction efficiency as a function of drive power. The diffractionefficiency is the optical power in the diffracted beam divided by the incident optical power. Thediffraction efficiency increases with drive power and then saturates at a value near 100%. Thismeans that almost all the incident light gets into the diffracted beam. For this example, it takes onlya few hundred milliwatts to reach high values of diffraction efficiency. For other devices, it maytake several watts.

Fig. 16Diffraction efficiency as a function of drive power for a

commercial acousto-optic modulator

As one example of the complexity that a drive circuit for an acousto-optic device can take, Figure17 shows a circuit that has been developed to drive a 50-watt, 24-MHz laser Q-switch.

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 16: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 16Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

Again, the manufacturers of commercial acousto-optic light-beam modulators, deflectors, and Q-switches generally also supply a line of power supplies for their devices. The voltages andimpedances and drive power capabilities of particular power supplies are matched to therequirements of individual acousto-optic devices. The frequencies of these power supplies are oftenin the range of hundreds of megahertz.

Helium-neon laser (one with plane polarized output preferred)

Electro-optic modulator

DC power supply for modulator

Sine-wave variable-frequency power supply for modulator

Power meter compatible with laser

Photodiode detector and appropriate circuitry

Oscilloscope and cables

Sheet polarizer

Polarizing prisms (one if He-Ne laser output is plane polarized, otherwise, two)

Angular rotation mount

Acousto-optic light-beam deflector

Acoustic signal generator (power supply)

Angular rotation mount for deflector

Screen

Meter stick

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 17: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 17Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

First you will operate an electro-optic modulator and measure some of its characteristics.

In these procedures, observe all appropriate safety procedures, and use laser protective eyewearaccording to the rules of your laboratory.

You will need a beam of plane polarized light from the helium-neon laser. Determine thepolarization of the laser light by placing a piece of sheet polarizer in the beam, mounted on theangular rotation mount. Direct the beam emerging from the polarizer into the power meter. Rotatethe polarizer through 360?�and observe the variation of the power meter. If the beam is planepolarized, the reading of the power meter should decrease to zero at two positions 180?�apart. Atangles that are 90?�from the positions where the intensity is zero, the intensity will rise to amaximum. In this case, when the laser output is plane polarized, it may be used as is.

If the light passing through the polarizer does not decrease to zero at two positions 180?�apart, it isnot plane polarized. It may be unpolarized (intensity does not change as the polarizer is rotated) orpartially polarized (intensity goes through two minima 180?�apart, but the minima are greater thanzero). In either case, a polarizing prism must be used to yield plane polarized light. Use a polarizingprism rather than sheet polarizer. The prism will give better results. Direct the beam through thepolarizing prism. The beam emerging from the prism should be plane polarized. Check it again,using the sheet polarizer, to be sure.

Now set up the electro-optic modulator and use it to modulate the laser beam. Set up theexperimental arrangement shown in Figure 18. The first polarizing prism will not be required if thelaser was originally plane polarized. Carefully align the modulator so that the light beam passesaccurately along the axis of the device and emerges with minimum loss of intensity. Mount thesecond polarizing prism on an angular rotation mount so that the beam passes through it and entersthe power meter. Rotate the prism until the light transmitted through it is at a minimum. Theminimum should be near zero.

Fig. 18Experimental arrangement for electro-optic

light-modulation measurement

The orientation of the polarizer and analyzer at 45?�to the vertical, as shown in Figure 19, is acommon configuration, used with many commercial modulators, especially modulators employingmaterials like ADP. But the orientation depends on the particular electro-optic material used and onthe direction in which the crystal has been cut. Consult the manufacturer’s instructions to ensureproper orientation of the modulator and the orientation of the pass directions for the polarizer andanalyzer.

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 18: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 18Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

Fig. 19Commonly used orientation of modulator element

and polarization directions

Next connect the DC power supply to the electrical connectors on the case of the modulator. Turnon the power supply and gradually increase the voltage from zero. Observe the increase in the lightreaching the power meter. As you increase the voltage in steps, record the voltage and the powermeter reading at each step. The power meter reading should increase with increasing voltage at first.Then a maximum reading will be reached and, with further increase in voltage, the power meterreading should begin to decrease. When you have reached this point, you may terminate this part ofthe measurement. The value of the voltage at which the power is maximum is the half-wave voltage.

Plot the power meter reading as a function of the applied voltage and determine the value of thehalf-wave voltage. Determine the extinction ratio for the modulator. The extinction ratio is thepower meter reading when the applied voltage is equal to the half-wave voltage divided by thepower meter reading when the voltage is zero.

Use the plot of power versus applied voltage to derive the birefringence D n as a function of appliedvoltage. Use the equation:

P(V) = P(V1/2) ?�sin2 (p D n/l )

to determine D n as a function of voltage V. Here P(V) is the meter reading at voltage V, P(V1/2) isthe meter reading at the half-wave voltage V1/2, L is the length of the crystal, and l is the wavelength(632.8 nm). You will need to determine the value of L. Either use the value specified by themanufacturer or carefully measure the length of the crystal.

Solve the equation above for D n at several values of voltage V, using the values of P(V) obtainedabove. Then plot D n as a function of voltage V.

Next, you will modulate the light at a high frequency. Remove the DC power supply and connectthe sine-wave generator to the modulator. Replace the power meter with the photodiode and directthe beam onto the photodiode. Connect the output of the photodiode circuit to the oscilloscopeinput. Turn on the power supply and adjust the voltage so that the peak of the sine wave is equal tothe half-wave voltage. This will lead to maximum contrast in the modulated beam.

Observe the output of the detector on the oscilloscope. The scope trace should show a modulatedoutput. Vary the frequency of the sine-wave generator and observe how the oscilloscope signalchanges.

With the frequency of the sine-wave generator set at a fixed value, measure the frequency of themodulation. Measure the time between successive maxima in the intensity of the modulated signal.Use the known sweep speed of the oscilloscope to make this measurement. Calculate the frequencyof the modulation, which is equal to the reciprocal of the time just measured. Compare thisfrequency to the frequency of the sine wave produced by the sine-wave generator.

Next you will operate an acousto-optic light-beam deflector. Set up the experimental arrangementshown in Figure 20. The acousto-optic device should be inserted in an angular rotation mount.Angular adjustment is needed so that the light beam intersects the acoustic wavefronts at the Braggangle. It is possible to calculate the Bragg angle and set the acousto-optic device in place at theproper angle, but it is usually more simple to rotate the device until optimum operation is obtained.

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 19: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 19Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

Fig. 20Experimental arrangement for

acousto-optic light-beam deflection

During the initial alignment, the drive power from the signal generator should be off. When theacousto-optic device is in place, turn on the laser, but do not turn on the signal generator. Adjust theposition of the laser beam and the acousto-optic device so that the beam passes undeflected throughthe acousto-optic device. The undeflected beam should emerge from the acousto-optic devicetraveling in the same direction as the original beam. Adjust the alignment until this occurs.

Turn on the signal generator and increase the drive power until most of the light goes into thedeflected beam. Project the deflected beam onto the screen, at a distance of several meters from thedeflector. The drive power will be kept constant and the frequency will be varied. This will changethe acoustic wavelength and will deflect the beam. The deflection of the beam will be observedthrough movement of the spot of light on the screen.

To observe the deflection, vary the acoustic frequency and note how the spot of light moves acrossthe screen. Measure the total distance on the screen through which the beam can be deflected. Itmay be necessary to adjust the alignment so that the total motion of the spot stays on the screen. Tomeasure the deflection angle, set the drive frequency at its lowest value. Determine the position x1where the beam strikes the screen. Change the drive frequency to its highest value and measure theposition x2 where the beam strikes the screen. Use the meter stick to measure the distance x1- x2.

Now use the meter stick to measure the distance D from the deflector to the screen. Measure to thescreen at the midpoint between x1 and x2. Calculate the maximum deflection angle f of the beamusing the equation:

sin (F /2) = |x1 – x2|/2D

Compare the result to the specification for the detector.

Now determine the number of resolvable spots that this deflector can achieve. First determine thebeam-divergence angle of the laser, either by measuring it directly through measuring the beamdiameter at a known large distance from the laser or by using the specification given by the lasermanufacturer. Calculate the number of resolvable spots by dividing the beam-deflection angle fobtained above by the beam-divergence angle. Compare your result to the specified value for theacousto-optic deflector.

Electro-optic measurements

Observation Voltage (volts) Power meter reading(milliwatts)

1.

2.

3.

4.

5.

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 20: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 20Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

6.

7.

8.

9.

10.

11.

12.

Distance between maxima on scope trace (divisions) ______

Scope sweep speed (microseconds per division) ______

Acousto-optic measurements

Distance x1 - x2 (cm) ______

Distance D (m) ______

1. Describe the operation of electro-optic devices and give a list of potential applications.

2. Define extinction ratio as it applies to an electro-optic modulator.

3. An electro-optic modulator has an intrinsic transmission of 95% (5% insertion loss). The crystalin it is 3 mm long. A light beam with a wavelength of 633 nm is directed through it. Voltage isapplied so that the induced change in index of refraction is 0.0001. Calculate the transmission of theelectro-optic modulator.

4. Define the difference in operation for an electro-optic modulator operated in the longitudinal andtransverse modes. Draw a diagram illustrating each configuration. Compare the characteristics ofeach mode.

5. Describe the operation of acousto-optic devices and give a list of potential applications.

6. Draw and label a block diagram of a simple acousto-optic beam-deflection system.

7. State the equation for the rise time for an acousto-optic modulator as a function of laser-beamdiameter. Calculate and plot the rise time as a function of the spot diameter over the range from 10to 1000 micrometers for a device fabricated from lithium niobate that has an acoustic velocity of6.57 ?�105 cm/sec.

8. An argon laser beam with wavelength 514.5 nm is directed through a tellurium dioxide acousto-optic light-beam deflector excited by a100-MHz acoustic wave. Tellurium dioxide has an acoustic velocity of4.2 ?�105 cm/sec. Calculate the deflection angle for the beam.

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.

Page 21: Course 4, Module 7_ Electro-Optic and Acousto-Optic Devices

Page 21Course 4, Module 7: Electro-Optic and Acousto-Optic Devices

8.12.2010 15:10:39http://utopia.cord.org/cm/leot/course04_mod07/mod04_07.htm

9. Compare the speed and number of resolvable spots for electro-optic and acousto-optic light-beamdeflectors.

Berg, N. J., and J. N. Lee, editors. Acousto-Optic Signal Processing, Theory and Implementation. New York: Marcel Dekker, Inc., 1983.

Goldstein, R. "Electro-Optic Devices in Review." Lasers and Applications, April 1986.

Gottlieb, M., C. L. M. Ireland, and J. M. Ley. Electro-Optic and Acousto-Optic Scanning and Deflection. New York: Marcel Dekker, Inc?�,1983.

Higgins, T. V. "There is a lot more to an A-O modulator than meets the eye." Laser Focus World, July 1991: 133.

Kaminow, I. P. An Introduction to Electro-optic Devices. New York: Academic Press, 1974.

Korpel, A. Acousto-Optics. New York: Marcel Dekker, Inc., 1988.

Main, R. P. "Fundamentals of Acousto-Optics." Lasers and Applications, June 1984: 111.

Yariv, A. Quantum Electronics. 3rd ed. New York: Wiley, 1988.

---Course Contents---

---Next Module---

Please purchase PDFcamp Printer on http://www.verypdf.com/ to remove this watermark.