Corrosion mapping
-
Upload
abhisheikgh42 -
Category
Technology
-
view
197 -
download
1
description
Transcript of Corrosion mapping
![Page 1: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/1.jpg)
REMEDIAL ENGINEERING
CORROSION MAPPING
ABHISHEK.G.H M-TECH(CONSTRUCTION TECHNOLOGY)
![Page 2: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/2.jpg)
INTRODUCTION:-
Corrosion mapping is a non intrusive technique which maps materials thickness using ultrasonic technology.
Variation in material thickness due to corrosion can be identified and graphically portrayed as an image format
![Page 3: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/3.jpg)
Continue,,,,,,,,,,,,,,,,,
Conventional manual ultrasonic inspection is the most reliable technique for measuring wall thickness.
The measured wall thickness is read from the ultrasonic device and reported.
![Page 4: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/4.jpg)
-:SCHEMATIC DIAGRAM:-
![Page 5: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/5.jpg)
-:GRAPHICAL REPRESENTATION:-
![Page 6: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/6.jpg)
-:COMPARISION:-
![Page 7: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/7.jpg)
![Page 8: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/8.jpg)
-:ROBOTIC INSTRUMENTS:-
![Page 9: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/9.jpg)
HUGE STRUCTURES CAN BE ANALYSED
![Page 10: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/10.jpg)
-:INSTRUMENTS:-
![Page 11: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/11.jpg)
-:M.C.MILLER TEST FOR CONCRETE MAPPING:-
-:Preparation of test surface :- A. Use a measuring tape to lay out a grid of
the test location (typically) on four foot centers covering the entire area which is to be tested.
B. Mark each test location with the spray paint.
C. Remove all asphalt, waterproofed surface or insulating films from each test location. This requires only a spot about two inches square.
![Page 12: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/12.jpg)
D. All test points should be wetted with electrical contact solution prior to testing, and the location must still be damp at the time of actual testing.
![Page 13: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/13.jpg)
-:PROCEDURE:-
1. Using the M.C. Miller concrete reference electrode assembly, place the CuCuSO4 apparatus onto the concrete surface in an area protected from foot and road traffic.
2. Connect the reference cell to the reel of test wire.
![Page 14: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/14.jpg)
3. Connected a test wire onto reinforced steel site or metal component.
4. Using the voltmeter, measure and record the potential difference between the reference cell and the reinforced steel or metal component.
5. With the reference cell assembly location unchanged, repeat the procedure.
6. Repeat as necessary to obtain sufficient data.
![Page 15: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/15.jpg)
-:TYPICAL CONCRETE SLAB WITH REINFORCEMENT (REBAR):-
![Page 16: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/16.jpg)
-:BENEFITS:-
Thin locations are reproduced directly in color, on-the-spot results.
Indications can easily be measured, both in surface and in form.
High degree of reproducibility.
![Page 17: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/17.jpg)
No ionizing radiation with regard to the taking of on-stream pictures.
No disruption of other activities. Data, a constant C-scan, are digitally
stored and saved.
![Page 18: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/18.jpg)
-: APPLICATIONS :-
Pressure Vessels and Systems. Pipework (T-joints , elbow joints) Reactors. Storage Tanks.
![Page 19: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/19.jpg)
-:LIMITATIONS:-
110V - 240V Power Required.Material to be Inspected must be
Penetrable by Ultrasonic Sound Waves.
Surface must be Clean & Free from Loose Material, Rust etc.
![Page 20: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/20.jpg)
-:CONCLUSION:-
The techniques is widely used in oil and gas industries for inservice detection and characteristics of corrosion in pipes and vessels.
The data is stored on a computer and may be color coded to show difference in thickness readings.
Corrosion may be mapped using zero degree ultrasonic probes,an eddy current array and or tiome of flight detection methods.
![Page 21: Corrosion mapping](https://reader034.fdocuments.net/reader034/viewer/2022051313/549ec5d7b4795988208b487f/html5/thumbnails/21.jpg)
-: THANK YOU :-