Control. Not Compromise. Control. Not Compromise.

Prime&Bond Elect™ Universal Dental AdhesiveA flexible solution for all bonding applications.

Selective-EtchIn selective-etch mode, Prime&Bond Elect™ virtually eliminates the risk of sensitivity on dentin by minimizing exposure to etchant. During a selective-etch application, the viscosity of the Caulk® 34% Tooth Conditioner Gel gives you better application control at the enamel-dentin junction. In addition, Prime&Bond Elect™

provides high bond strength to dentin (in deep Class II restorations), as well as creating a tight seal at the enamel margin.

CLINICAL SITUATIONS:

Direct Restorations (all cavity classes)

Uninstrumented Enamel

Indirect Inlay/Onlay Cementation*

Self-EtchWhen using Prime&Bond Elect™ with a self-etch method, there’s no need to compromise bond strength or risk sensitivity. Prime&Bond Elect™ assures virtually no sensitivity and creates high bond strength.

CLINICAL SITUATIONS:

Indirect Full-Coverage Crown*

Endo Post Cementation*

Total-EtchPrime&Bond Elect™ is ideal in clinical situations where there is a large amount of enamel, such as veneer placement. With a total-etch application, Prime&Bond Elect™ creates a strong bond on enamel and dentin.

CLINICAL SITUATIONS:

Indirect Veneer Cementation

Small or Shallow Direct Restorations

Direct Veneers

Class IV Restorations

Class V Restorations

Prime&Bond Elect™

Caulk® 34% Tooth Conditioner Gel

Caulk® 34% Tooth Conditioner Gel applied over entire prep

* Mix with self cure activator

A reliable, convenient, universal adhesive for any bonding technique.Every procedure is different, and with new Prime&Bond Elect™ Universal Dental

Adhesive you can use your preferred etching method — total-etch, self-etch or

selective-etch — across all direct and indirect indications. Built on the clinically

proven chemistry of Prime&Bond® NT™ adhesive, you can be confident that

you’re achieving the consistent, high bond strengths necessary to meet the

clinical needs of your patients, with virtually no post-operative sensitivity.

High bond strength

Low fi lm thickness

Virtually no sensitivity

Resin

Adhesive Layer

Enamel

Resin

Adhesive Layer

Enamel

Self-Etch Total-Etch

MP

a

20.221.7 37.0

32.0

5 Second DryMoist

Consistent, High Bond StrengthPrime&Bond Elect™ has low water uptake and provides a high bond strength when placing direct or indirect material on dentin and enamel. In addition, consistent bond strength is achieved across varied moisture levels.

Low Film ThicknessWith a rise in esthetic restorations and increased milling accuracy*, the film thickness of the adhesive layer is becoming more critical to allow passive seating of the crown. Prime&Bond Elect™ provides a lower film thickness of resin-dentin and resin-enamel interfaces, as highlighted below.

Virtually No SensitivityIn a recent clinical trial, Prime&Bond Elect™ displayed low post-operative sensitivity.1 The advanced technology behind Prime&Bond Elect™ enables minimal microleakage, helping ensure a tight seal.

Representative FE-SEM of a resin-enamel interface produced with Prime&Bond Elect™ applied in self-etching mode.

Representative FE-SEM of a resin-enamel interface produced with ScotchBond™ Universal applied in self-etching mode.

Total-Etch Shear Bond Strength of Prime&Bond Elect™ on Dentin

Consistent bond strength on tooth surfaceswith varied moisture levels.

*CEREC® machine accuracy is 25µm (data on file)

Built on proven chemistry.Prime&Bond Elect™ is built on the

chemistry of Prime&Bond® NT™, one of

the world’s most widely used and clinically

tested adhesives. Administered over

one billion times throughout the world,

Prime&Bond® NT™ delivers a sensitivity-

free post-operative experience virtually

every time.

Based on more than 13 years of trusted,

clinically proven PENTA (dipentaerythritol

penta acrylate monophosphate) resin

technology, Prime&Bond Elect™ can be

used in virtually all restorative bonding

procedures. The chemistry uses acetone

to chase away water, which allows the

resins and fillers to penetrate into the

dentinal tubules, enabling a strong bond.

IN ADDITION, UNIQUE PENTA CHEMISTRY:

Eliminates worry about adequate bonding

Instills confidence from dependable, long-term clinical results

1 billionapplicationsover 13 yearsapplicationsover 13 yearsapplications

36.5

37.9

33.2

24.1

Dentin Enamel

Prime&Bond Elect™

Scotchbond™

UniversalOptiBond™

Solo Plus

MP

a

33.2

36.5

18.5

29.4

33.9

23.7

Prime&Bond Elect™

Scotchbond™

Universal

Dentin Enamel

OptiBond™

XTRCLEARFIL™

SE Bond

MP

a

37.9

24.1 24.421.7

36.9

23.0

34.0

24.9

24-hour Notched Edge Shear Bond Strength in Self-Etch Application

24-hour Notched Edge Shear Bond Strength in Total-Etch Application

38 West Clarke Avenue • Milford, DE 19963 • 800.532.2855 • www.caulk.com • www.dentsply.com1All data on file. Scotchbond™ Universal, OptiBond™ XTR, CLEARFIL™ SE Bond, OptiBond™ Solo Plus and CEREC are not registered trademarks of DENTSPLY International.Form 534902 (9/11/12)

www.PrimeandBondElect.com

Ordering Information634602 Introductory Kit 1 Bottle Prime&Bond Elect™ (5mL) 1 Syringe Caulk® 34% Tooth Conditioner Gel (3mL) 25 Applicator Tips 50 Flocked Applicator Tips 1 Dispensing Well

634600 Dual Cure Introductory Kit 1 Bottle Prime&Bond Elect™ (5mL) 1 Syringe Caulk® 34% Tooth Conditioner Gel (3mL) 25 Applicator Tips 1 Bottle Self Cure Activator (4.5mL) 50 Flocked Applicator Tips 1 Dispensing Well

634601 Bottle Refill 1 Bottle Prime&Bond Elect™ (5mL)

634604 Unit Dose Package 50 Unit Doses 2 Unit Dose Holders 50 Flocked Applicator Tips

634603 Unit Dose Package 100 Unit Doses 3 Unit Dose Holders 100 Flocked Applicator Tips

646125 Caulk® 34% Tooth Conditioner Gel Refill 2 Syringes (3mL each) 25 Disposable Applicator Tips (Needles)

646126 Applicator Tips Refill Package (25 Blue Tips)

©2012 DENTSPLY International. All rights reserved.