Composite Field Multiplier based on Look-Up Table for Elliptic Curve Cryptography Implementation
-
Upload
marisa-paryasto -
Category
Documents
-
view
591 -
download
1
description
Transcript of Composite Field Multiplier based on Look-Up Table for Elliptic Curve Cryptography Implementation
ITB J. ICT, Vol. 6, No. 1, 2012, 63-81 63
Received November 29th, 2011, Revised April 16
th, 2012, Accepted for publication April 25
th, 2012.
Copyright © 2012 Published by LPPM ITB,ISSN: 1978-3086, DOI: 10.5614/itbj.ict.2012.6.1.4
Composite Field Multiplier based on Look-Up Table
for Elliptic Curve Cryptography Implementation
Marisa W. Paryasto1, Budi Rahardjo
1, Fajar Yuliawan
2, Intan Muchtadi-
Alamsyah2& Kuspriyanto
1
1School of Electrical Engineering and Informatics, Institut Teknologi Bandung
Jl. Ganesha No. 10 Bandung 40132 – Indonesia 2Algebra Research Group, Faculty of Mathematics and Natural Sciences,
Institut Teknologi Bandung, Jl. Ganesha No. 10 Bandung 40132 – Indonesia
Email: [email protected]
Abstract. Implementing a secure cryptosystem requires operations involving
hundreds of bits. One of the most recommended algorithm is Elliptic Curve
Cryptography (ECC). The complexity of elliptic curve algorithms and
parameters with hundreds of bits requires specific design and implementation
strategy. The design architecture must be customized according to security requirement, available resources and parameter choices. In this work we propose
the use of composite field to implement finite field multiplication for ECC
implementation. We use 299-bit keylength represented in GF((213)23) instead of
in GF(2299). Composite field multiplier can be implemented using different
multiplier for ground-field and for extension field. In this paper, LUT is used for
multiplication in the ground-field and classic multiplieris used for the extension
field multiplication. A generic architecture for the multiplier is presented.
Implementation is done with VHDL with the target device Altera DE2. The work
in this paper uses the simplest algorithm to confirm the idea that by dividing
field into composite, use different multiplier for base and extension field would
give better trade-off for time and area. This work will be the beginning of our more advanced further research that implements composite-field using
Mastrovito Hybrid, KOA and LUT.
Keywords: composite field; cryptography, elliptic curve, finite field, multiplier,
security.
1 Introduction
Elliptic Curve Cryptography (ECC) is a public-key encryption that requires high computation for solving complex arithmetic operations. Elliptic curve is
used in cryptography because of its special mathematical properties match
cryptographic requirements for encryption and decryption. Elliptic curve has its own arithmetic operation, that is very specific and unpredictable, makes it
cryptographically strong and becomes the most preferable cryptography
algorithm to replace RSA. Unfortunately, implementing ECC requires
sophisticated mathematical skills. There are many layers, restrictions, and
64 Marisa W. Paryasto, et.al.
combinations that make various ECC implementations difficult to compare.
Every level of ECC offers many things to explore. In this work we focus on the
lowest level: finite field operations. Since multiplication is the most frequently
used operations, we investigate existing multipliers algorithms and make improvements.
The keylength used in ECC determines the level of security. In general, longer
key requires more components in the corresponding hardware implementation. As the internet technology grows, the demand to implement ECC on constraint
devices increases. As a consequence, there is a need for efficient algorithm and
architecture for implementing ECC on constraint devices. To fulfill the security
level requirement at the present, ECC should have above 160 bits keylength.
We choose to implement 299 bits in this research. However implementing 299-
bit ECC in constrained devices, simulated with FPGA board, cannot be done
using conventional algorithm and architecture. For example, 299-bit binary classic multiplier cannot fit in most FPGA devices. One alternative solution is
by using composite field.
Composite field can be seen as a finite field divided into subfields (ground fields) and extended fields. The representation of composite field can be seen as
composing a long string of bits into smaller groups of bits. This representation
allows arithmetic operations to be done in smaller chunks of string so the
complex operations can be broke down into simpler operations. The focus of our paper is the implementation of multiplier using composite field. We focus
on multiplier because multiplication is the most frequently used operation in
ECC. The benefit of using composite field is the lower of memory usage and lower components. Thus if the process of multiplication is more efficient, the
whole performance of cryptosystem will be improved.
This work uses of composite field characteristic of dividing one big chunk of
operation into smaller ones, with the classic multiplication for the extension field multiplication and LUT for base multiplication. We chose to use the
easiest multiplier algorithm just to confirm the idea that composite field is
promising to be able to perform operations for long bits.
2 Background and Previous Work
2.1 Elliptic Curves
Given a field F of characteristic 2, an elliptic curve E over F is an equation of
the form
y2 + a1xy + a3y = x
3 + a2x
2 + a4x + a6,
Elliptic Curve Cryptography Implementation 65
where a1,a2 ,a3,a4,a6 in F.
The set of rational points on E over F denoted by E(F) is
E(F) = {(x,y) ∈ F2 : y
2 + a1xy + a3y = x
3 + a2x
2 + a4x + a6} ∪ {𝑂}
where O is the projective closure of the equation y2 + a1xy + a3y = x
3 + a2x
2 +
a4x + a6 .The point O is called the point at infinity.
The set of rational points E(F) carries a commutative group structure with some
addition operation with the point at infinity acting as the zero element. The following is the explicit formula for the group operation.
Composition Rule. Let P,Q∈E, and L be a line connecting P and Q (the tangent
line of E if P=Q), and R the third point which is the intersection of L and E. Let
L’ be the line connecting R and O. Then P+Q will be the point where L’ intersect E.
Proposition 1. The composition rule above satisfies the following:
If L intersect E at P,Q,R (not necessarily different) then (P+Q)+R=O.
1. P+O = P for all P∈ E
2. P+Q=Q+P for all P,Q∈ E
3. For all P∈ E there exists a point (-P), such that P+(-P)=O
4. For all P, 𝑄, 𝑅 ∈ E(P+Q)+R=P+(Q+R).
5. Hence E with the composition rule form an abelian group with identity O.
Explicit Group Operation. Let E be an elliptic curve satisfies the Weierstrass
equation
E: y2 + a1xy + a3y = x
3 + a2x
2 + a4x + a6
1. Let P0 = (x0, y0) ∈ E. Then −P0 = (x0,−y0 − a1x0 − a3).
2. Let P1 + P2 = P3 with Pi = (xi, yi)∈ E. If x1 = x2and y1 + y2 + a1x2 + a3 = 0,
then P1 + P2 = O.
Otherwise, let
66 Marisa W. Paryasto, et.al.
𝜇 =𝑦2−𝑦1`
𝑥2−𝑥1`,
𝜗 =𝑦1𝑥2−𝑦2𝑥1
𝑥2−𝑥1`
for𝑥1 ≠ 𝑥2, and
𝜇 =3 𝑥1
2+2𝑎2𝑥1`+𝑎4−𝑎1𝑦1`
2𝑦1`+𝑎3+𝑎1𝑥1`
𝜗 =− 𝑥1
3+𝑎4𝑥1`+2𝑎6−𝑎3𝑦1`
2𝑦1`+𝑎3+𝑎1𝑥1`
for𝑥1 = 𝑥2.
Then 𝑦 = 𝜇𝑥 + 𝜗 is the line through P1and P2, or the tangent line of E if P1= P2.
3. P3 = P1 + P2 is given by
x3 = 𝜇2+ a1 𝜇 − a2 − x1 − x2
y3 = −( 𝜇 + a1)x3 − 𝜗 − a3.
For an integer m and P∈ E, define
[m]P = P + … + P (m terms) for m> 0,
[0]P = O, and [m]P = [−m](−P) for m< 0
The El Gamal elliptic curve encryption based on binary field is as following:
INPUT: Elliptic curve domain parameter (k,E,P,n), public key Q, plaintext m
OUTPUT: Ciphertext (C1,C2)
1. Represent the message m as a point M in E(GF(2k))
2. Select k ∈[1, n-1]
3. Compute C1=[k]P
4. Compute C2=M+ [k]Q
5. Return (C1,C2)
Elliptic Curve Cryptography Implementation 67
The encryption process is shown in Figure 1
Figure 1 Encryption process in ECC.
For the decryption is as following:
INPUT: Elliptic curve domain parameter (k,E,P,n), private key d, ciphertext
(C1,C2)
OUTPUT: Plaintext m
1. Compute M= C2 –[d] C1
2. Extract m from M
3. Return (m)
Figure 2 Decryption process in ECC.
From the elliptic curve encryption and decryption and elliptic curve operation,
one can see that the role of operations in ground field is very important. In this
research we choose composite field as the ground field.
2.2 Composite Fields
Assume that 𝑞 is a number to be used to construct a field.𝑞does not have to be
prime if the order of the finite field is power of a prime or 𝑞 = 𝑝𝑚 where 𝑝 is a prime. Thus the finite field can be extends to an extension field so the field
𝐺𝐹(𝑞𝑛) can be extended to 𝐺𝐹((𝑞𝑛 )𝑚 ).
68 Marisa W. Paryasto, et.al.
Both in hardware or software implementation performing finite field
arithmetics, choosing 𝑞 = 2 is a big advantage because information is only
representated in 0 or 1.
Referring to [1], certain kinds of finite field can be defined as:
Two pairs of 𝐺𝐹 2𝑛 , 𝑄 𝑦 = 𝑦𝑛 + 𝑞𝑖𝑛−1𝑖=0 𝑦𝑖 dan 𝐺𝐹 2𝑛 𝑚 , 𝑃 𝑥 = 𝑥𝑚 +
𝑝𝑖𝑥𝑖𝑚−1
𝑖=0 is a composite field if 𝐺𝐹(2𝑛) is constructed as extension field of
𝐺𝐹(2) by 𝑄(𝑦) and 𝐺𝐹( 2𝑛 𝑚 ) is construced as extension field of 𝐺𝐹(2𝑛 ) by
𝑃(𝑥). 𝑄 𝑦 and 𝑃(𝑥)is irreducible polynomials over 𝐺𝐹(2).
Mathematically, 𝐺𝐹((2𝑛 )𝑚 ) is isomorphic to 𝐺𝐹(2𝑘) for 𝑛. 𝑚 = 𝑘 [2]. Although
a field of order 2𝑛𝑚 is isomorphic to a field of order 2𝑘 , the algorithmic
complexity of both fields are different in additions and multiplication
operations. Generally it depends on the chosen 𝑚 and 𝑛 and more specifics on polynomials 𝑄(𝑦) and 𝑃(𝑥) [3].
All curve representations in 𝐺𝐹(2𝑘) can be converted to curves in 𝐺𝐹((2𝑛 )𝑚 ) . If
both 𝐹 and 𝐹′ are finite fields with equal number of elements, there exists way to correlate each element in 𝐹 with corresponding element in 𝐹′ so addition and
multiplication tables of 𝐹 and 𝐹′are equal (𝐹 and 𝐹′ isomorphic)[4], Theorem
2.60 page 104.Curve representations in composite field converted to non-composite field has been done in [5].
In finite field, composite field can perform same operations as non-composite.
Only the operation has to be modified to be able to do in composite
representation. In composite field, the field is divided into sub-fields. 𝐺𝐹 28 can be divided into 𝐺𝐹((22)4) or 𝐺𝐹((24)2). Sub-fields can be processed faster dan
implemented in parallel.
The reason why we use GF((213
)23
) in this implementation is because GF((2
13)
23)=GF(2
299) which complies with the security level needed. The other
reasons is that GCD(13,23)=1 so irreducible polynomial can be used for both
ground field and extension field, and there are trinomials and polynomials available. Carefully chosen irreducible polynomial will reduce the complexity
of multiplication operation.
Previous Works. The first idea multiplier for composite field was initiated by
Mastrovito [6]. The multiplier is called hybrid-multiplier. It performs the multiplication by doing multiplication serially in the ground field and parallel in
the extension field. Mastrovito's multiplier basically works using a
multiplication matrix that includes the reduction process. Paar in his works [3],[7],[8] added some improvements to Mastrovito's. Paar implemented
Elliptic Curve Cryptography Implementation 69
multiplication in the ground field using KOA and Mastrovito for multiplication
in the extension field. Later, Rosner [9] conducted further research of
Mastrovito and Paar.
Look-Up Table (LUT) for composite field operations has been implemented in [9]. The algorithm for ground field multiplication using logaritmic table lookup
is proven to be fast.
3 Methodology
3.1 Look-Up Table (LUT)
LUT is used for storing log and alog (anti log) table to make multiplication operation in the ground field GF(2
n) perform faster. In [2] it is concluded that n
does not have to be exactly the same as a single computer word (e.g. 8, 16). It
has been proved that n <2is more efficient because the table will be smaller and
thus will take advantage of the first level cache of computers.
One of the reason why this research uses LUT for storing precomputed log and
alog table in GF(213
) is that Table 2 in [2] shows that LUT for n =13 is
efficient for polynomial basis multiplication compared to bigger n. To construct logaritmic lookup table, a primitive element g in GF(2
n) is selected to be the
generator of the field GF(2n), so that every element A in this field can be written
as a power of g as A=gi , where 0 < i < 2
n-1 . Then the powers of the primitive
element gi can be computed for i=0, 1, 2,.. , 2
n-1, and obtain 2
n pairs of the form
(A, i). Two tables sorting these pairs have to be constructed in two different
ways: the log table sorted with respect to A and the alog table sorted with the
respect i. These tables then can be used for performing the field multiplication, squaring and inversion operations. Given two elements A, B in GF(2
n) , the
multiplication C=AB is performed as follows:
1. i := log[A]
2. j := log[B]
3. k := i+j (mod 2n-1)
4. C := alog[k]
70 Marisa W. Paryasto, et.al.
The steps above is based on the fact that C = AB = gigj = g
i+j mod 2n-1. Ground
field multiplication requires three memory access and a single addition
operation with modulus 2n-1.
Savas and Koc [2] also proposed the use of the extended alog table for eliminating modular addition operation (step 3). The extended alog table is 2
n+1-
1 long, which is about twice the length of the standard alog table. It contains
the values (k, gk) sorted with repect to the index k , where k = 0, 1, 2, . . .,2
n+1-2
. Since the values of i and j in step 1 and 2 of the multiplications are in the
range 0, 2n-1 , the range of k = i + j is 0, 2
n+1-2 . Thus modular addition
operation can be omitted and the ground field multiplication operation can be
simplified as follows:
1. i := log[A]
2. j := log[B]
3. k := i + j
4. C := extended-alog[k]
Figure 3 shows the process of reading LUT to compute multiplication using log
and alog table.
Figure 3 Multiplying using LUT.
Elliptic Curve Cryptography Implementation 71
Figure 4 13-bit LUT implementation.
Figure 5 Multiplication of GF(24) using log and alog table with LUT.
72 Marisa W. Paryasto, et.al.
Figure 6 The waveform of multiplication of GF(24) using log and alog table
with LUT.
Figure 4 shows the RTL diagram of LUT implemented using Quartus and
Altera DE2while Figure 5 shows the RTL of GF(24) using LUT for storing log
and a-log table with algorithm from [2]. There are two LUTs in the
implementation, one is for storing 24-blocks log table, and the other is for
storing 24 –blocks alog table. Log table put n-bits i values on the first column
and n-bits gi values on the second column. alog table sorted the table based on
gi values, and put the corresponding i values on the second column. Thus, each
multiplier unit requires at least one LUT for storing i and j values in serial implementation and two LUTs for parallel implementation. Another LUT is
needed for storing alog table.
Figure 6 shows the simulation waveform of multiplier implemented in Figure 5.
As a comparison, Figure 7 shows that straightforward 299-bit implementation failed for the available resources.
4 Design and Implementation
The generic architecture of our circuit is shown in the Fig 8. On the left side
there are two set of input registers, each for input A and B. The size of the input
registers depends on the bit size. For our particular case, which is a custom
design, it is 13-bit. If we use off the shelf components, we may have to use 16-bit registers since common components usually have 2
n word size.
Elliptic Curve Cryptography Implementation 73
Figure 7 Failed implementation for straightforward 299-bit implementation.
Figure 8 Multiplier General Architecture.
74 Marisa W. Paryasto, et.al.
Right next to the input registers are temporary registers that are used to store
addition terms before they are multiplied. The decision will effect the number of
temporary registers (and adders needed).
In the center of our circuit is the GF(213
) multiplier. In this particular design we have only one multiplier, implemented as LUT multiplier. Multiplication is
done in serial fashion. Figure 9 shows an estimated timing diagram, which will
be implemented in the sequencer. For example, when multiplying a22 andb22, the enable lines of registers related to those element and the result register are
activated.
If area is permitting, we could add more multipliers to perform parallel
multiplication. Additional multipliers will reduce the time to perform all multiplications at the expense of more area. Careful timing consideration must
be done in order to avoid race condition is multiple multipliers are
implemented.
The results of multiplications are stored in temporary registers before they are
added to create the final results. Thus, there is a network of adders on the right
side.
Figure 9 Estimated timing diagram.
Elliptic Curve Cryptography Implementation 75
Figure 10 below is the snippets of VHDL code LUT implementing GF(213
)
multiplier. A 13-bit multiplier requires 213
entries ≈ 8000 entries, for each table.
If we implement this in general purpose hardware then it should be
implemented in 16 bit (2 bytes). In our implementation, the log and alog table occupies 2*8*2 bytes = 32 Kbytes .
Figure 10 Snippet ofGF(213) LUT implementation in VHDL.
ECC Processor Architecture. Figure 11 shows the general architecture of
ECC processor. FFAU (Finite Field Arithmetic Unit) is an arithmetic unit
specifically used for calculating finite fields operations.
The processor will accept input data (plaintext) through data_in pin then will
process the command given according to the opcode. The processor will execute
the command after “start” command. Status of the processor (busy, done) can be monitored through “status” line. After the process is done, the result (ciphertext)
will be send through “data_out” pin. “reset” pin is used to return the processor
to the initial state.
The ECC processor can process data in different length of bits. For long bits, the transfer process has to be carefuly considered to fit in the data bus. General
process (clk) begin
if clk'event and clk = '1' then
case a is
when "0000000000000" => i <= "0000000000001";
when "0000000000001" => i <= "0000000000010";
when "0000000000010" => i <= "0000000000100";
when "0000000000011" => i <= "0000000001000";
when "0000000000100" => i <= "0000000010000";
when "0000000000101" => i <= "0000000100000";
…
76 Marisa W. Paryasto, et.al.
computers use 32-bits data bus. Meanwhile the data to be processed by ECC
processor is more than 100bits length.
Figure 11 ECC top level processor architecture.
Figure 12 FFAU (Finite Field Arithmetic Unit).
One method to solve this is to divide data into several blocks (for example each
blocks is 32-bit length) and load the data to the processor several times. Even
I/O
Control Unit
Register
Finite Field Arithmetic Unit (FFAU)
clk
data
bus
data bus data bus
data bus
reset
start
opcode
status
data in
data out
ECC processor
1.2
control bus
control bus
Elliptic Curve Cryptography Implementation 77
for the most extreme cases, data can be loaded serially. This ECC processor has
several parameters stored in the register. The parameters are elliptic curve
equation used, private key and public key. The parameters can be stored
permanently (hardcoded) or can be loaded through the ”data_in” using a specific opcode. ”reset” pin is used to set the parameter to the initial condition
(for example all zero). At the earlier stage of research, the parameters are stored
permanently to simplify the problem.
Figure 12 shows the block diagram of FFAU shown earlier in Figure 11.
GF((213
)23
) requires 23 GF(213
) multipliers. Figure 13 shows the concept of
GF((213
)23
) multiplier.
Figure 13 GF(213)23) Classical Multiplier-LUT.
5 Analysis
We compare our composite field multiplier with standar non-composite
multipliers: classic multiplier, interleaved multiplier, Karatsuba-Offman
multiplier, Mastrovito multiplier Type-1 and Type-2 and Montgomery multiplier.
The experiment is done by running each multiplier using Quartus II Version 9.1
Build 350 03/24/2020 SP 2 SJ Web Edition. All multipliers are implemented
using family device is Stratix II, device EP2S15F484C3.
As shown in Table 1, not all multipliers design fit in the standard device. Only
interleaved multiplier and Mastrovito 2 multiplier can handle up to 233 bits.
78 Marisa W. Paryasto, et.al.
Our design has been tested for lower bits and gives promising result that it can
also works for 233 bits or more. This is the subject of our further research since
the architecture should be customized to able to process longer bits.
Table 2 shows the result of all multipliers comparation based on logic utilization, combinational ALUT(s), dedicated logic registers, total registers and
total pins. The performance of our multiplier is in general better than other
multipliers except it requires more pins.
Our multiplier number of register is 56% lower than interleaved and
Montgomery multiplier and 83% lower than Karatsuba multiplier. Karatsuba
multiplier requires more register due to its recursive process in multiplying
process.
The use of combinational ALUT is less than 1%, which makes our multiplier
use combinational ALUT less than Mastrovito, Mastrovito 2, Classic and
Karatsuba.
Our design uses more pins as a tradeoff of less registers and ALUT.
Figure 15shows gives multipliers compared with all variables. Figure 16 is the
brief version of Figure 15, focusing on variables not significantly observed in Figure 15.
Figure 14 Multiplier Area Usage Comparison.
Elliptic Curve Cryptography Implementation 79
Table 1 Multiplier Comparison.
Stratix II
Logic
utiliza-
tion (%)
Combina-
tional
ALUT(s)
Combina-
tional
ALUT(s)
(%)
Dedicated
logic
registers
Dedica-
ted logic
registers
(%)
Total
regis-
ters
Total
pins
Total
pins
(%)
Composite < 1 91/12480 < 1 24/12480 < 1 24 122/343 36
Mastrovito 2 169/12480 1 0/12480 0 0 48/343 14
Mastrovito 2 2 128/12480 1 0/12480 0 0 48/343 14
Interleaved < 1 31/12480 < 1 55/12480 < 1 55 52/343 15
Classic 2 128/12480 1 0/12480 0 0 48/343 14
Montgomery < 1 28/12480 1 55/12480 < 1 55 52/343 15
Karatsuba 2 187/12480 1 141/12480 1 141 44/343 13
Table 2 Multiplier Processing Limit.
Multiplier m
Classic 8, 16, 32, 64, 128, 163
Interleaved 8, 16, 32, 64, 128, 163, 233 Mastrovito 8, 16, 32, 64 Mastrovito 2 8, 16, 32, 64, 128, 163, 233 Montgomery 8, 16, 32, 64, 128 Karatsuba-Offman 8, 16, 32, 64 Composite *our experiments so far shows
a strong indication that it is implementable for m >= 233
Figure 15 Multiplier Comparison.
80 Marisa W. Paryasto, et.al.
Figure 16 Brief Multiplier Comparison.
6 Conclusions
Our multiplier has been compared with other multipliers and the result
conforms our hypothesis that our multiplier gives better trade off for time and space, like shown in Figure 15 and Figure 16. The number of total pins is
higher in order to lower the use of ALUT and registers.
The experiment results in Table 1 shows that composite field implementation
requires less combinational ALUT and registers (area) than most of multipliers. This advantage achieved by gaining better trade off for time is space is the
flexibility of the architecture design that can be modified to fit devices
according to space of time available.
Acknowledgement
This research is supported by Hibah Kompetensi DIKTI based on SK Dekan
STEI No. 0930/I1.C07.1/DN/2011. We thank Muhammad Hafiz Khusyairi and Nopendri Zulkifli for their inputs and discussions on the topic.
References [1] Guajardo, Jorge, Efficient Algorithms for Elliptic Curve Cryptosystem,
Master’s thesis, Worcester Polytechnic Institute, 1997.
[2] Savas, E. & Koc, C.K., Efficient Methods for Composite Fields
Arithmetic, Technical report, Oregon State University, 1999.
Elliptic Curve Cryptography Implementation 81
[3] Paar, Christof, Efficient VLSI Architectures for Bit-parallel Computation
in Galois Fields, PhD thesis, 1994.
[4] Deschamps, Jean-Pierre, Imana, Jose Luis& Sutter, Gustavo D.,
Hardware Implementation of Finite-Field Arithmetic, The McGraw Hill Companies, Inc., 2009.
[5] Hoffstein, Jeffrey, Pipher, Jill & Silverman, Joseph H., An Introduction to
Mathematical Cryptography, Springer Science+Business Media, LLC, 2008.
[6] Edoardo, Mastrovito, VLSI Architecture for Computations in Galois
Fields, PhD thesis, Linkoping University, 1991.
[7] Paar, Christof, Fast Arithmetic Architectures for Public-Key Algorithms over Galois Fields GF((2n)m), Number 1233 in Lecture Notes in
Computer Science, Springer-Verlag, pp. 363–378, 1997.
[8] Paar, Christof & Fleischmann, Peter, Fast Arithmetic for Public-Key Algorithms in Galois Fields with Composite Exponents, IEEE
Transactions on Computers, 48(10), pp. 1025–1034, October 1999.
[9] Rosner, Martin Christopher, Elliptic Curve Cryptosystems on Reconfigurable Hardware, Master’s thesis, Worcester Polytechnic
Institute, May 1998.