Composite and PCB Based Implementations of a Solar Panel ...
Transcript of Composite and PCB Based Implementations of a Solar Panel ...
SPA
CE
SYST
EMS
GR
OU
PU
nive
rsity
of F
lorid
a, G
aine
sville
, Flo
rida
3261
1
08/10/10 1
Composite and PCB Based Implementations of a Solar Panel Design for SwampSat
Sharan Asundi, Matthew Mahin, Vivek Nagabhushan, Tzu Yu Lin, Norman G. Fitz-Coy
08/10/2010
24th Annual AIAA/USU Conference on Small SatellitesAugust 9-12, 2010 · Utah State University · Logan, Utah USA
SPA
CE
SYST
EMS
GR
OU
PU
nive
rsity
of F
lorid
a, G
aine
sville
, Flo
rida
3261
1
08/10/10 2
Rapid Retargeting and Precision Pointing
SwampSat Mission• Rapid Retargeting and Precision Pointing
– Precision 3-axis attitude control
• Validate…– Attitude Determination System (ADS)– Command and Data Handling System (CDH)– Telemetry, Tracking and Command (TT&C)– Electrical Power System (EPS)
SPA
CE
SYST
EMS
GR
OU
PU
nive
rsity
of F
lorid
a, G
aine
sville
, Flo
rida
3261
1
08/10/10 3
SwampSat Subsystem Assembly
1. CMG Based ACS2. Electrical Power System3. SwampSat Transceiver4. SwampSat Flight Computer5. Solar Panels6. Solar Cells7. Sun Sensor8. Sun Sensor Filter9. Motor Driver Board10.Structure11.Receive Antenna Module12.Transmit Antenna Module SwampSat Subsystem Assembly
SPA
CE
SYST
EMS
GR
OU
PU
nive
rsity
of F
lorid
a, G
aine
sville
, Flo
rida
3261
1
08/10/10 4
• Satisfy requirements across subsystems• Adhere to CubeSat form factor• Surface suitable for mounting solar cells• Embed magnetic coils for angular momentum
management• Provision for mounting Sun sensors, temperature
sensors, diodes, etc• Structural members and debris abatement• Interface peripheral components with the respective
subsystem boards• Accommodate Delrin plate design and enable
access to connectors through them
Motivation and Requirements
SwampSat Solar Panel Design
SPA
CE
SYST
EMS
GR
OU
PU
nive
rsity
of F
lorid
a, G
aine
sville
, Flo
rida
3261
1
08/10/10 5
Solar Panel Design
• Sun sensor – TEMT6000• Temperature Sensor –
LM135/335• Bypass diode – BAS40-04• Connector for solar cells
and temperature sensor• Connector for magnetic
coils• Connector for Sun sensor
Solar Panel Design
SPA
CE
SYST
EMS
GR
OU
PU
nive
rsity
of F
lorid
a, G
aine
sville
, Flo
rida
3261
1
08/10/10 6
Carbon Fiber Composite Solar Panel• Magnetic coils prepared from enamel coated 30
AWG copper core wire and EPO-TEX 78-165 epoxy• Two metal plates with a spacer sandwiched
between are held together by a nut and bolt• Metal rods used for guiding the path of copper wire • Layers of magnetic coils secured together in place
by the epoxy and cured for 10 minutes at 1000 C or 30 minutes at 800 C
Magnetic Coil Fabrication Fixture and Finished Coil
SPA
CE
SYST
EMS
GR
OU
PU
nive
rsity
of F
lorid
a, G
aine
sville
, Flo
rida
3261
1
08/10/10 7
Carbon Fiber Composite Solar Panel
A Composite Panel Under Development
• Wet lay up technique using a carbon fiber fabric is chosen for implementing the composite
• Composite preparation vacuum bagged on cured for 3-4 hours at room temperature
• EPO-TEK 78-165 conductive epoxy from Epoxy Technology, conductive pen and metal foil tape used for laying electrical traces
• CV-2566 CV Silicone elastomer used for mounting solar cells
SPA
CE
SYST
EMS
GR
OU
PU
nive
rsity
of F
lorid
a, G
aine
sville
, Flo
rida
3261
1
08/10/10 8
Printed Circuit Board (PCB) Solar Panel• 6-layer 1mm thick PCB with FR-4 cores• 5-layers have electrical traces as magnetic coils• 2oz per square foot copper traces• Dual side solder mask with fully insulated vias• Immersion gold over electroplated nickel finish• Each panel accommodates ~71 turns of coil
A Multifunctional PCB Solar Panel
SPA
CE
SYST
EMS
GR
OU
PU
nive
rsity
of F
lorid
a, G
aine
sville
, Flo
rida
3261
1
08/10/10 9
Composite vs PCB Panel
Composite Solar Panel PCB Solar Panel
Composite solar panels PCB solar panels
Solar panel epoxy can lead to outgassing Suited for solder paste or epoxyHeat dissipation is not an issue Heat dissipation might be an issueElectrical traces and pads are manually laid Electrical traces and pads are machinedWet layup technique can lead to outgassing PCB boards are machine fabricatedPanel thickness ~2.5 mm (with coils) Panel thickness ~1 mm
SPA
CE
SYST
EMS
GR
OU
PU
nive
rsity
of F
lorid
a, G
aine
sville
, Flo
rida
3261
1
08/10/10 10
Tests and Results
Composite and PCB Panel Evaluation
Basis…• Composite coil has
more turns• PCB coil has more
area• Magnetic moment is
assumed to be equal
u – magnetic momentn - # of turnsI – currentA – vector area of each loop
u = nIA
SPA
CE
SYST
EMS
GR
OU
PU
nive
rsity
of F
lorid
a, G
aine
sville
, Flo
rida
3261
1
08/10/10 11
Tests and Results (cont’d…)
PCB Solar Panel Vibration Test Setup and Profile(Ref. PSD table in the Cubesat to PPOD ICD)
SPA
CE
SYST
EMS
GR
OU
PU
nive
rsity
of F
lorid
a, G
aine
sville
, Flo
rida
3261
1
08/10/10 12
Conclusion• PCB panels are selected for SwampSat mission for
reliability and compact packaging• CubeSat form factor and SwampSat mission limit the
thickness to be under ~1mm• PCB panel address the requirements of…
– EPS subsystem– ACS subsystem– ADS subsystem– Structural and cabling requirement– Facilitate TT&C subsystem
• PCB panels are well designed within the limits…– Copper pads for solar cells, sensors and pheripherals– Connectors for interfacing with subsystem boards– SwampSat power budget is designed to accommodate the
power requirement of the embedded coils
SPA
CE
SYST
EMS
GR
OU
PU
nive
rsity
of F
lorid
a, G
aine
sville
, Flo
rida
3261
1
08/10/10 13
• Precisely determine the magnetic field output by the embedded magnetic coils
• Perform thermal analysis and evaluate heat dissipation capability
• PCB panels can accommodate additional turns to accommodate future missions
• Capability of the embedded magnetic coils to manage SwampSat’s angular momentum
• Accommodate different orientations of solar cells, alternate PCB material, solar cell mounting technique…
Future Work
SPA
CE
SYST
EMS
GR
OU
PU
nive
rsity
of F
lorid
a, G
aine
sville
, Flo
rida
3261
1
08/10/10 14
Acknowledgements
• SwampSat development team– Everything and more!!
• Vijay Jagdale, Dr. Ifu and Dr. Shankar– Composite fabrication facility and assistance
• Timco Engineering– Vibration testing facility
• Peggy Evanich– Everything and much more!!
SPA
CE
SYST
EMS
GR
OU
PU
nive
rsity
of F
lorid
a, G
aine
sville
, Flo
rida
3261
1
08/10/10 15
Thank You!!
Questions?
Sharan [email protected], 352-846-3020
Space Systems Group @ University of Florida