Compliance and Safety Manual.pdf
-
Upload
arun-mishra -
Category
Documents
-
view
225 -
download
0
Transcript of Compliance and Safety Manual.pdf
-
7/29/2019 Compliance and Safety Manual.pdf
1/31
Chapter 1 Regulatory Compliance Statement 1-1...............................................
Chapter 2 Regulatory Compliance Information 2-1............................................
2.1 Regulatory Compliance Standards 2-1.........................................................
2.2 European Directives Compliance 2-1...........................................................
2.3 USA Regulatory Compliance (FCC Part 15) 2-1..........................................
2.4 Japan Regulatory Compliance 2-2...............................................................
2.5 CISPR 22 Compliance 2-2...........................................................................
Chapter 3 Safety Information 3-1..........................................................................
3.1 Overview 3-1................................................................................................
3.1.1 Conventions Used 3-1..........................................................................
3.1.2 General Requirements 3-2...................................................................
3.2 Electricity Safety 3-3.....................................................................................
3.2.1 High Voltage 3-3..................................................................................
3.2.2 Power Cable 3-3..................................................................................
3.2.3 Tools 3-4..............................................................................................
3.2.4 Drilling 3-4............................................................................................
3.2.5 Thunderstorm 3-5.................................................................................
3.2.6 Electrostatic 3-5...................................................................................
3.3 Fuse 3-6.......................................................................................................
3.4 Working at Heights 3-6.................................................................................
3.4.1 The Safety Codes on Ladder-using 3-7...............................................
3.4.2 Weight Hoisting 3-7..............................................................................
3.5 Miscellaneous 3-8.........................................................................................
3.5.1 Lifting Heavy Objects 3-8.....................................................................
3.5.2 Sharp Objects 3-8................................................................................
3.5.3 Plug/Unplug Board 3-9.........................................................................
3.5.4 Binding Signal Cables 3-9....................................................................
Chapter 4 Sicherheitsinformationen 4-1..............................................................
-
7/29/2019 Compliance and Safety Manual.pdf
2/31
Huawei Technologies Proprietary
HUAWEI
HUAWEI MSOFTX3000 Mobile SoftSwitch Center
Compliance and Safety Manual
V100R003
-
7/29/2019 Compliance and Safety Manual.pdf
3/31
Huawei Technologies Proprietary
HUAWEI MSOFTX3000 Mobile SoftSwitch Center
Compliance and Safety Manual
Manual Version T2-032281-20060425-C-3.05
Product Version V100R003
BOM 31220381
Huawei Technologies Co., Ltd. provides customers with comprehensive technical support
and service. Please feel free to contact our local office or company headquarters.
Huawei Technologies Co., Ltd.
Address: Administration Building, Huawei Technologies Co., Ltd.,
Bantian, Longgang District, Shenzhen, P. R. China
Postal Code: 518129
Website: http://www.huawei.com
Email: [email protected]
-
7/29/2019 Compliance and Safety Manual.pdf
4/31
Huawei Technologies Proprietary
Copyright 2006 Huawei Technologies Co., Ltd.
All Rights Reserved
No part of this manual may be reproduced or transmitted in any form or by any
means without prior written consent of Huawei Technologies Co., Ltd.
Trademarks
, HUAWEI, C&C08, EAST8000, HONET, , ViewPoint, INtess, ETS, DMC,
TELLIN, InfoLink, Netkey, Quidway, SYNLOCK, Radium, M900/M1800,
TELESIGHT, Quidview, Musa, Airbridge, Tellwin, Inmedia, VRP, DOPRA,
iTELLIN, HUAWEI OptiX, C&C08iNET, NETENGINE, OptiX, iSite, U-SYS, iMUSE,
OpenEye, Lansway, SmartAX, infoX, and TopEng are trademarks of Huawei
Technologies Co., Ltd.
All other trademarks and trade names mentioned in this manual are the property of
their respective holders.
Notice
The information in this manual is subject to change without notice. Every effort has
been made in the preparation of this manual to ensure accuracy of the contents,
but all statements, information, and recommendations in this manual do not
constitute the warranty of any kind, express or implied.
-
7/29/2019 Compliance and Safety Manual.pdf
5/31
Huawei Technologies Proprietary
Compliance and Safety Manual
HUAWEI MSOFTX3000
-
7/29/2019 Compliance and Safety Manual.pdf
6/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Table of Contents
Huawei Technologies Proprietary
i
Table of Contents
Chapter 1 Regulatory Compliance Statement............................................................................ 1-1Chapter 2 Regulatory Compliance Information.......................................................................... 2-1
2.1 Regulatory Compliance Standards.................................................................................... 2-12.2 European Directives Compliance ...................................................................................... 2-12.3 USA Regulatory Compliance (FCC Part 15) ..................................................................... 2-12.4 Japan Regulatory Compliance........................................................................................... 2-22.5 CISPR 22 Compliance....................................................................................................... 2-2
Chapter 3 Safety Information ....................................................................................................... 3-13.1 Overview............................................................................................................................ 3-1
3.1.1 Conventions Used................................................................................................... 3-13.1.2 General Requirements............................................................................................ 3-2
3.2 Electricity Safety ................................................................................................................ 3-33.2.1 High Voltage............................................................................................................ 3-33.2.2 Power Cable............................................................................................................ 3-33.2.3 Tools........................................................................................................................ 3-43.2.4 Drilling ..................................................................................................................... 3-43.2.5 Thunderstorm.......................................................................................................... 3-53.2.6 Electrostatic............................................................................................................. 3-5
3.3 Fuse................................................................................................................................... 3-63.4 Working at Heights............................................................................................................. 3-6
3.4.1 The Safety Codes on Ladder-using ........................................................................ 3-73.4.2 Weight Hoisting ....................................................................................................... 3-7
3.5 Miscellaneous .................................................................................................................... 3-83.5.1 Lifting Heavy Objects .............................................................................................. 3-83.5.2 Sharp Objects.......................................................................................................... 3-83.5.3 Plug/Unplug Board.................................................................................................. 3-93.5.4 Binding Signal Cables............................................................................................. 3-9
Chapter 4 Sicherheitsinformationen ........................................................................................... 4-14.1 berblick............................................................................................................................ 4-1
4.1.1 Symbolerluterung.................................................................................................. 4-14.1.2 Allgemeine Anforderungen...................................................................................... 4-2
4.2 Elektrische Sicherheit ........................................................................................................ 4-34.2.1 Hochspannung ........................................................................................................ 4-34.2.2 Zuleitung.................................................................................................................. 4-44.2.3 Werkzeuge.............................................................................................................. 4-54.2.4 Bohren..................................................................................................................... 4-54.2.5 Gewitter................................................................................................................... 4-6
-
7/29/2019 Compliance and Safety Manual.pdf
7/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Table of Contents
Huawei Technologies Proprietary
ii
4.2.6 Elektrostatische Entladung...................................................................................... 4-64.3 Sicherung........................................................................................................................... 4-74.4 Arbeiten in groen Hhen.................................................................................................. 4-7
4.4.1 Sicherheitshinweise fr die Benutzung von Leitern................................................ 4-8
4.4.2 Lastenaufzug........................................................................................................... 4-84.5 Sonstiges........................................................................................................................... 4-9
4.5.1 Anheben schwerer Gegenstnde............................................................................ 4-94.5.2 Scharfkantige Gegenstnde.................................................................................... 4-94.5.3 Einsteckplatinen .................................................................................................... 4-104.5.4 Zusammenlegen von Signalleitungen................................................................... 4-10
-
7/29/2019 Compliance and Safety Manual.pdf
8/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center List of Figures
Huawei Technologies Proprietary
iii
List of Figures
Figure 1-1 European Community CE Certification DoC ........................................................1-1Figure 3-1 Diagram of wearing electrostatic protection wrist strap........................................ 3-6Figure 3-2 Weight hoisting.....................................................................................................3-8Figure 4-1 Darstellung des geerdeten Armbandes................................................................ 4-7Figure 4-2 Lastenaufzug ........................................................................................................4-9
-
7/29/2019 Compliance and Safety Manual.pdf
9/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center List of Tables
Huawei Technologies Proprietary
iv
List of Tables
Table 2-1 Regulatory compliance standards..........................................................................2-1Table 3-1 Safety symbols and descriptions............................................................................3-1Table 4-1 Sicherheitssymbole und Beschreibung..................................................................4-2
-
7/29/2019 Compliance and Safety Manual.pdf
10/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 1 Regulatory Compliance Statement
Huawei Technologies Proprietary
1-1
Chapter 1 Regulatory Compliance Statement
Figure 1-1 European Community CE Certification DoC
-
7/29/2019 Compliance and Safety Manual.pdf
11/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 2 Regulatory Compliance Information
Huawei Technologies Proprietary
2-1
Chapter 2 Regulatory Compliance Information
2.1 Regulatory Compliance Standards
Table 2-1 Regulatory compliance standards
Discipline Standards
EMC
FCC Part 15 (CFR 47) Class A
VCCI Class A
CISPR22 Class A
EN55022 Class A
AS/NZS 3548 Class AETSI EN 300 386 V1.3.1
EN50024
Safety
IEC 60950:1999
EN 60950:2000
EN 60825-1/2:2000
AS/NZS 60950:2000
2.2 European Directives ComplianceHUAWEI MSOFTX3000 complies with the following European Directives: 89/336/EC
(electromagnetic compatibility), 73/23/EC (low voltage).
See Figure 1-1 for Huawei's Declaration of Conformity
2.3 USA Regulatory Compliance (FCC Part 15)
HUAWEI MSOFTX3000 complies with Part 15 of the FCC Rules. Operation is subject
to the following two conditions:
z This device may not cause harmful interference.
z This equipment must accept any interference received, including interference that
may cause undesired operation.
If the customer modifies the equipment without the authorization of Huawei, which
directly or indirectly contributes to the equipment incompliance with FCC requirements
for Class A digital equipment, Huawei is not liable for such interference problem and the
expenses incurred therefrom shall be covered by the customer.
-
7/29/2019 Compliance and Safety Manual.pdf
12/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 2 Regulatory Compliance Information
Huawei Technologies Proprietary
2-2
2.4 Japan Regulatory Compliance
HUAWEI MSOFTX3000 complies with the requirements of VCCI Class A Information
Technology Equipment (ITE).
Warning: If this equipment is used in a domestic environment, radio disturbance might
arise. When such trouble occurs, the user may be required to take corrective actions.
2.5 CISPR 22 Compliance
HUAWEI MSOFTX3000 complies with the requirements of CISPR 22 for Class A
Information Technology Equipment (ITE).
Warning: If this equipment is used in a domestic environment, radio disturbance might
arise. When such trouble occurs, the user may be required to take corrective actions.
-
7/29/2019 Compliance and Safety Manual.pdf
13/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 3 Safety Information
Huawei Technologies Proprietary
3-1
Chapter 3 Safety Information
3.1 Overview
This section introduces part of the safety precautions that should be followed during the
installation and maintenance of the equipment of Huawei.
Before performing any operation, read the operation instructions and precautions
carefully to minimize the risk of accidents. The Note, Caution, Warning and Danger
items in other manuals do not cover all safety precautions that should be followed.
They are only the supplements to the safety precautions for operations as a whole.
Therefore, the personnel in charge of the installation and maintenance of the Huaweiproducts are required to understand these basics of safety operation.
In performing various operations, follow the local safety regulations. The safety
precautions introduced in the product manuals are supplementary and subject to the
local safety regulations.
When carrying out operations on Huawei products, follow the precautions and special
safety instructions provided by Huawei.
The personnel in charge of the installation and maintenance must be well-trained to
adopt the proper operating methods and observe all safety precautions. All installation
and maintenance people must be well-trained and qualified.
3.1.1 Conventions Used
Table 3-1 shows the symbols used in this manual. The symbols are used to remind you
of the safety precautions during equipment installation and maintenance.
Table 3-1 Safety symbols and descriptions
Safetysymbol
Description
Generic alarm symbol suggests a general safety concern.
ESD protection symbol suggests electrostatic-sensitiveequipment.
Electric shock symbol suggests a danger of high voltage.
Microwave symbol suggests a high-intensity electromagnetic field.
Laser symbol suggests a strong laser beam.
-
7/29/2019 Compliance and Safety Manual.pdf
14/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 3 Safety Information
Huawei Technologies Proprietary
3-2
Safety precautions are classified into the following levels: Danger, Warning, Caution
and Note.
Danger: Suggests the possibility of a fatal accident or body injury if safety precautions
are ignored.Warning: Suggests the possibility of a major accident or severe injury, or equipment
damage, if safety precautions are ignored.
Caution: Suggests the possibility of a severe injury, or equipment damage, if safety
precautions are ignored.
Note: Suggests the possibility of an injury or equipment damage, if safety precautions
are ignored
3.1.2 General Requirements
In order to reduce the technically unavoidable residual risk to a minimum, it is
imperative to follow the rules below:
z Read all the instructions before operation.
z The equipment is suitable for mounting on concrete or other non-combustible
surface only.
z When installing the unit, always make the ground connection first and disconnect it
last.
z Never defeat the ground conductor or operate the equipment in the absence of a
suitably installed ground conductor. Conduct the appropriate electrical inspection.
z Connect the unit/system to the protection ground before permanent operation.
The cross section of protective earthing conductor must be at least 10 mm2.
z For DC supplied model, the equipment applies to DC power supply that complies
with the Safety Extra-Low Voltage (SELV) requirements in IEC 60950 is based
safety standards.
z Before operation, the equipment must be fixed securely on the floor or other
reliable objects, such as walls and mounting racks.
z Installation, configuration and disassembly must be done only by trained
personnel according to the documents concerned.
z The unit/system must be operated by experts and authorized users only.z Any replacement or change to the system or parts of the system (including the
software) must be done by qualified or authorized personnel of Huawei.
z Any fault and error that might affect safety must be reported immediately by the
user to the person in charge.
z Removal or disabling of safety facilities, troubleshooting, and maintenance of the
equipment must be done by qualified specialists only.
All parts of the document must be followed to the full. The document also serves as a
guide to the selection of measuring and test equipment.
-
7/29/2019 Compliance and Safety Manual.pdf
15/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 3 Safety Information
Huawei Technologies Proprietary
3-3
3.2 Electricity Safety
3.2.1 High Voltage
Danger:
High voltage power supply offers electric power for equipment operation. Direct contact
or indirect contact (through damp objects) with high voltage and AC mains supply may
result in fatal danger.
z During the installation of AC power supply facility, the local safety regulations mustbe followed. The personnel who install the AC facility must be qualified for high
voltage and AC operations.
z Conductive articles, such as watch, hand chain, bracelet and ring are prohibited
during the operation.
z When water is found in the rack, or the rack is damp, immediately switch off the
power supply.
z When operation is performed in a damp environment, make sure that water is kept
off the equipment.
Warning:
Non-standard and improper high voltage operations may result in fire and electric
shock. Therefore, when bridging and wiring the AC cable across a certain area, follow
the local rules and regulations. The personnel who perform high voltage operations
should be qualified for high voltage and AC operations.
3.2.2 Power Cable
Note:
Installation and removal of live power cable is prohibited strictly. Transient contact
between the core of power cable and conductor may generate spark or electric arc,
which may lead to fire or eye injury.
-
7/29/2019 Compliance and Safety Manual.pdf
16/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 3 Safety Information
Huawei Technologies Proprietary
3-4
z Before the power cable is installed or removed, the power switch must be turned
off.
z Before the power cable is connected, it must be confirmed that the power cable
and label comply with the requirements of the actual installation.
Note:
Use power cables, whose cross sections are greater than 25 mm2, to connect the
equipment powered by DC.
3.2.3 Tools
Warning:
During high voltage and AC operations, special tools should be used. It is not permitted
to use common tools or tools brought by the operator.
3.2.4 Drilling
Warning:
Drilling on the rack without permission is strictly prohibited. Drilling that does not satisfy
the requirements concerned may damage the wires and cables inside the rack. If the
metal swarf from the drilling gets into the rack, it may result in short-circuit of the circuit
boards.
z If it is necessary to drill a hole on the rack, insulation protection gloves must be
worn, and the cables inside the rack should first be removed.
z During the drilling, make sure that the eyes of the operator are well protected. The
spattering swarf may cause injury to the eyes.
z Make sure that the metal swarf does not get into the rack.
z Non-standard drilling operation may damage the electromagnetic shielding
performance of the rack.
-
7/29/2019 Compliance and Safety Manual.pdf
17/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 3 Safety Information
Huawei Technologies Proprietary
3-5
z After the drilling, clean up the metal swarf in time.
3.2.5 Thunderstorm
Danger:
High voltage and AC operations, or operations on a steel tower or a mast on a
thunderstorm day are prohibited.
On a thunderstorm day, the electromagnetic field generated in the thunderstorm area
may cause damage to electronic parts. In order to prevent the equipment from beingdamaged by lightning, proper grounding is required.
3.2.6 Electrostatic
Caution:
The static electricity generated by human body may damage the electrostatic-sensitive
components on the circuit board, such as large-scale integrated circuit (LIC).
z In the case of human body moving, clothes friction, friction between shoes and
ground, or holding ordinary plastic in hand, the human body will generate a static
electromagnetic field that will remain with the human body for a long time.
z Before touching the equipment, ejector, circuit boards, or ASICs, wear a grounded
electrostatic discharge(ESD) wrist strap to prevent the sensitive components from
being damage by the electrostatic in human body.
-
7/29/2019 Compliance and Safety Manual.pdf
18/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 3 Safety Information
Huawei Technologies Proprietary
3-6
Figure 3-1 Diagram of wearing electrostatic protection wrist strap
3.3 Fuse
Warning:
For the safety of continuous operation, replace the fuse with that of the same type and
rating, if necessary.
3.4 Working at Heights
Warning:
When working at heights, watch out for falling objects.
High-altitude work should comply with the following requirements:
z Operators working at high-altitude must be trained.
z Operating machines and tools should be carried and handled safely to avoid
falling.
z Take safety protection measures like wearing helmet and safety belt.
z In cold areas, heat-retaining clothes should be worn before high-altitude
operation.
-
7/29/2019 Compliance and Safety Manual.pdf
19/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 3 Safety Information
Huawei Technologies Proprietary
3-7
z All lifting appliances should be checked before high-altitude operation.
3.4.1 The Safety Codes on Ladder-using
Before using the ladder, first check if the ladder is damaged. Make sure the ladder is
safe for use. Overweight on the ladder is strictly prohibited.
The slant of the ladder is 75 at best. The slant can be measured with Angle Square or
with arms. When a ladder is used, the wider end of the ladder should be placed against
the ground or protective measures should be taken on the base part of the ladder for
the purpose of skid resistance. Place the ladder against a stable ground.
When climbing the ladder, do not deviate your center of gravity from the ladder edge. To
lessen the danger and ensure safety, three parts of the body should be on the ladder.
When climbing the ladder, the upper limit of the height should not exceed the highest
four steps. If one is about to climb to the top, the length of the ladder should be 1 meterhigher than the eave.
3.4.2 Weight Hoisting
Warning:
Access to the areas under the gib arm and the goods in suspension is strictly prohibited
when hoisting weight.
z The weight hoisting operators should undergo related training and be qualified.
The weight hoisting tools should be checked and be complete. Make sure that only
when the weight hoisting tools are firmly fixed onto the weight-bearing object or
the main wall can weight-hoisting operations be undertaken. Use concise
command to avoid mis-operation.
z The slant of the cabinet-top bearing cable for hoisting should not be greater than
90
to prevent the cable from breaking.
-
7/29/2019 Compliance and Safety Manual.pdf
20/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 3 Safety Information
Huawei Technologies Proprietary
3-8
Figure 3-2 Weight hoisting
3.5 Miscellaneous
3.5.1 Lifting Heavy Objects
Warning:
When lifting heavy objects, it is prohibited to stand or walk under the arm or the lifted
object.
3.5.2 Sharp Objects
Warning:
When the equipment is carried by hand, protection gloves should be worn to avoid
injury by sharp objects.
-
7/29/2019 Compliance and Safety Manual.pdf
21/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 3 Safety Information
Huawei Technologies Proprietary
3-9
3.5.3 Plug/Unplug Board
Note:
When plugging the board, the operator should not push it too hard. Otherwise, the pins
on the backplane may be distorted.
z The board should be inserted along the slot guide. Try to avoid the contact
between the circuit sides of two boards, which will result in short-circuit or scratch.
z When holding a board in hand, do not touch the board circuit, components,
connectors, and connection slots.
3.5.4 Binding Signal Cables
Note:
Signal cables should be bound separately from strong current electrical lines or high
voltage lines. The space between the binding should be 150mm at minimum.
-
7/29/2019 Compliance and Safety Manual.pdf
22/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 4 Sicherheitsinformationen
Huawei Technologies Proprietary
4-1
Chapter 4 Sicherheitsinformationen
4.1 berblick
Dieser Abschnitt macht Sie mit den Sicherheitsvorschriften vertraut, die Sie bei der
Installation und Instandhaltung der Ausrstung von Huawei beachten mssen.
Anmerkung:z Lesen Sie bitte alle Arbeitsanweisungen und Sicherheitshinweise sorgfltig durch ,
bevor Sie mit dem Arbeiten beginnen. Nur durch Beachtung dieser Hinweise lsst
sich das Unfallrisiko minimieren . Die in anderen Handbchern aufgefhrten
Symbole Anmerkung, Achtung, Warnung und Gefahrbeinhalten nicht alle zu
beachtenden Sicherheitshinweise. Sie dienen lediglich der Ergnzung. Deshalb
muss sich das fr die Installation und Instandhaltung der Ausrstung von Huawei
verantwortliche Personal mit allen Sicherheitshinweisen vertraut machen.
z Bei der Durchfhrung der verschiedenen Arbeitsschritte mssen auerdem die
rtlichen Sicherheitsvorschriften beachtet werden. Die in den Handbchern der
einzelnen Produkte aufgefhrten Sicherheitshinweise sind Ergnzungen und
unterliegen den nationalen Sicherheitsvorschriften.
z Whrend der Arbeit mit den Produkten von Huawei sind deshalb grundstzlich alleSicherheitsvorschriften und spezifischen Sicherheitshinweise genau zu beachten.
z Das fr die Installation und Instandhaltung der Produkte von Huawei
verantwortliche Pesonal muss geschult werden, um alle Sicherheitsvorschriften zu
kennen und die richtigen Arbeitsmethoden anwenden zu knnen. Nur geschultes
und qualifiziertes Personal kann die Installation und Instandhaltung in korrekter
Weise durchfhren.
4.1.1 Symbolerluterung
Die in diesem Handbuch verwendeten Symbole sind in der folgenden Tabelle
dargestellt. Diese Symbole sollen das Personal whrend der Installation und
Instandhaltung der Ausrstung an die Wichtigkeit der im Handbuch aufgefhrten
Sicherheitsvorschriften erinnern.
-
7/29/2019 Compliance and Safety Manual.pdf
23/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 4 Sicherheitsinformationen
Huawei Technologies Proprietary
4-2
Table 4-1 Sicherheitssymbole und Beschreibung
Symbol Erluterung
Alarm: Hinweis auf ein generelles Sicherheitsproblem
ESD-Schutz: Hinweis auf Beschdigung infolge elektrostatischerEntladung
Elektrischer Schlag: Hinweis auf Gefhrdung durch Hochspannung
Mikrowellen: Hinweis auf ein hochintensives elektromagnetischesFeld
Laser: Hinweis auf einen starken Laserstrahl
Die Sicherheitshinweise sind in die folgenden Gefahrenstufen eingeteilt: Gefahr,
Warnung, Achtung und Anmerkung.
Gefahr: Hinweis auf die Mglichkeit von Unfllen mit tdlichen Verletzungen bei
Nichtbeachtung der Sicherheitsvorschriften.
Warnung: Hinweis auf die Mglichkeit von schweren Unfllen, schweren
Krperverletzungen oder Beschdigungen der Ausrstung bei Nichtbeachtung der
Sicherheitsvorschriften.
Achtung: Hinweis auf die Mglichkeit von schweren Krperverletzungen oder
Beschdigungen der Ausrstung bei Nichtbeachtung der Sicherheitsvorschriften.
Anmerkung: Hinweis auf die Mglichkeit einer Krperverletzung oder Beschdigung
der Ausrstung bei Nichtbeachtung der Sicherheitsvorschriften.
4.1.2 Allgemeine Anforderungen
Um das technisch bedingte Restrisiko auf ein Minimum zu begrenzen, ist es unbedingt
erforderlich, die folgenden Regeln zu beachten:z Lesen Sie alle Anweisungen sorgfltig durch, bevor Sie mit dem Arbeiten
beginnen.
z Die Ausrstung kann nur auf Beton oder einer anderen nichtbrennbaren
Oberflche installiert werden.
z Beachten Sie, dass bei der Installation des Systems stets zuerst die
Erdverbindung angebracht wird und das die Erdverbindung stets als letztes
getrennt wird.
z Betreiben Sie die Ausrstung niemals ohne Erdung. Trennen Sie das System
nicht von der Erdung.
-
7/29/2019 Compliance and Safety Manual.pdf
24/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 4 Sicherheitsinformationen
Huawei Technologies Proprietary
4-3
z Das System muss vor der stndigen Inbetriebnahme geerdet werden. Der
Querschnitt der Erdverbindung sollte mindestens 10mm betragen.
z Mit Gleichstrom betriebenes Modell: Das Gert arbeitet mit Gleichstrom, wobei die
Anforderungen der Norm (IEC 60950) fr Schutzkleinspannung eingehaltenwerden mssen.
z Die Ausrstung muss fest und sicher auf dem Boden oder an geeigneten
Gegenstnden, wie z. B. Wnden oder Regalen, angebracht sein. Vergewissern
Sie sich vor der Inbetriebnahme, ob die Verankerung sicher ist.
z Installation, Einrichtung und Demontage der Ausrstung drfen nur durch
geschultes und qualifiziertes Fachpersonal durchgefhrt werden.
z Das System darf nur von qualifizierten und bevollmchtigten Fachkrften
betrieben werden.
z Jeder Austausch und jede nderung am System und seinen Teilen (einschlielich
der Software) darf nur vom qualifizierten und bevollmchtigten Fachpersonal vonHuawei durchgefhrt werden.
z Jeder aufgetretene Fehler und jede Funktionsstrung, welche die Sicherheit
gefhrden knnen, mssen unverzglich vom Betreiber dem verantwortlichen
Personal berichtet werden.
z Entfernen oder Abschalten von Sicherheitseinrichtungen sowie die Instandhaltung
der Ausrstung drfen nur von qualifizierten Fachkrften durchgefhrt werden.
Alle Teile dieses Handbuches sind zu beachten.Das Handbuch dient gleichzeitig als
Ratgeber bei der Auswahl von zustzlichen Messinstrumenten und Testvorrichtungen.
4.2 Elektrische Sicherheit
4.2.1 Hochspannung
Gefahr:
Hochspannungsleitungen stellen die fr die Arbeit der Ausrstung erforderliche
Energie zur Verfgung. Direkter oder indirekter Kontakt (z. B. durch feuchteGegenstnde) mit Hochspannung und Wechselstromversorgung kann zu tdlichen
Unfllen fhren.
z Bei der Installation der Wechselstromversorgung sind die rtlichen
Sicherheitsbestimmungen zu beachten. Das Personal muss besonders qualifiziert
sein fr das Arbeiten mit Hochspannung und Wechselstrom.
z Es ist nicht erlaubt whrend dieser Arbeiten leitende Gegenstnde wie Uhren,
Armbnder, Armreifen und Ringe am Krper zu tragen.
-
7/29/2019 Compliance and Safety Manual.pdf
25/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 4 Sicherheitsinformationen
Huawei Technologies Proprietary
4-4
z Sollte sich Wasser im Baugruppentrger befinden oder der Baugruppentrger
feucht sein, ist die Energiezufuhr sofort zu unterbrechen und das System
abzuschalten.
z
Muss in einer feuchten Umgebung gearbeitet werden, ist sicherzustellen, dasskein Wasser in die Ausrstung dringen kann.
Warnung:
Die Nichtbeachtung der Sicherheitsvorschriften bei der Arbeit mit Hochspannung kann
zu Feuer und elektrischem Schlag fhren. Deshalb muss die Verlegung von Leitungen
und Verbindungen den rtlichen Anforderungen und Sicherheitsvorschriften
entsprechen. Arbeiten mit Hochspannung drfen nur von qualifiziertem Fachpersonal
durchgefhrt werden.
4.2.2 Zuleitung
Anmerkung:
Das Entfernen und Anbringen von Zuleitungen ist strengstens verboten. Kurzschlssezwischen innerem und uerem Leiter knnen Lichtbgen oder Funkenflug
verursachen, was zu Feuer oder einer Augenverletzung fhren kann.
z Das System muss stets abgeschaltet werden, bevor die Zuleitung angebracht
oder entfernt wird.
z berprfen Sie vor dem Anbringen der Zuleitung immer, ob das von Ihnen
verwendete Kabel den Anforderungen entspricht.
Anmerkung:
Fr mit Gleichstrom betriebene Ausrstung benutzen Sie bitte eine 25 mm2 oder.
-
7/29/2019 Compliance and Safety Manual.pdf
26/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 4 Sicherheitsinformationen
Huawei Technologies Proprietary
4-5
4.2.3 Werkzeuge
Warnung:
Fr Arbeiten mit Hochspannung und Wechselstrom sind Spezialwerkzeuge zu
verwenden. Es ist nicht erlaubt, herkmmliche Werkzeuge oder Werkzeuge des
Bedienpersonals zu benutzen.
4.2.4 Bohren
Warnung:
Das Anbohren des Baugruppentrgers ist verboten. Am Baugruppentrger darf nur mit
Erlaubnis gebohrt werden. Um die Beschdigung der im Inneren des
Baugruppentrgers verlaufenden Kabel und Leitungen zu vermeiden, sind beim
Bohren die Sicherheitsanforderungen zu beachten. Beim Bohren knnen Metallspne
in den Baugruppentrger gelangen und Kurzschlsse in den Leiterplatten auslsen.
z Sollte es wirklich erforderlich sein, in den Baugruppentrger ein Loch zu bohren,
sind zuvor die Kabel aus dem Inneren des Baugruppentrgers zu entfernen.
Whrend des Bohrens sind isolierende Schutzhandschuhe zu tragen.
z Um die Verletzung der Augen durch umherfliegende Spne zu vermeiden, hat das
Personal eine Schutzbrille zu tragen.
z Vermeiden Sie, dass die Metallspne in den Baugruppentrger gelangen.
z Um die EM-Abschirmungseigenschaften des Baugruppentrgers zu erhalten,
mssen beim Bohren alle Sicherheitsanforderungen eingehalten werden.
z Entfernen Sie nach Beendigung des Bohrens bitte unverzglich alle Metallspne.
-
7/29/2019 Compliance and Safety Manual.pdf
27/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 4 Sicherheitsinformationen
Huawei Technologies Proprietary
4-6
4.2.5 Gewitter
Gefahr:
Arbeiten mit Hochspannung und Wechselstrom oder Arbeiten auf Stahltrmen und
masten whrend eines Gewitters sind verboten.
Das elektromagnetische Feld, das whrend eines Gewitters entsteht, kann die
Elektronik beschdigen. Um die Ausrstung vor Beschdigung durch Blitzschlag zu
schtzen, ist eine ordnungsgeme Erdung erforderlich.
4.2.6 Elektrostatische Entladung
Achtung:
Die durch den menschlichen Krper erzeugte elektrostatische Energie (statische
Elektrizitt) kann die gegen elektrostatische Entladung besonders empfindlichen Teile
der Leiterplatten, wie z. B. die Schaltkreise (LIC), beschdigen.
z Hlt man einen herkmmlichen Kunststoffgegenstand in der Hand, wird bei jeder
Bewegung des menschlichen Krpers durch die Reibung der Kleidung aneinander
oder durch die Reibung der Schuhe mit dem Boden ein elektromagnetisches Feld
erzeugt, welches fr lange Zeit im Krper bestehen bleibt.
z Deshalb ist es erforderlich, vor jeder Berhrung der Ausrstung, der Leiterplatten
oder Schaltungen ein geerdetes Armband zur elektrostatischen Entladung zu
tragen. So knnen die sensiblen Teile vor einer Beschdigung infolge der im
Krper vorhandenen Elektrostatik geschtzt werden.
-
7/29/2019 Compliance and Safety Manual.pdf
28/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 4 Sicherheitsinformationen
Huawei Technologies Proprietary
4-7
Figure 4-1 Darstellung des geerdeten Armbandes
4.3 Sicherung
Warnung:
Ersetzen Sie die Sicherung bei Bedarf immer nur mit einem Sicherungstyp, der die
gleichen technischen Daten besitzt.
4.4 Arbeiten in groen Hhen
Warnung:
Achten Sie beim Arbeiten in groen Hhen darauf, dass keine Gegenstnde auf die
Erde fallen knnen.
Bei Arbeiten in groen Hhen sollten die folgenden Anforderungen beachtet werden:
z Das Personal muss speziell dafr ausgebildet sein.
z Werkzeuge und andere Gegenstnde mssen sorgfltig und sicher transportiert
und gehandhabt werden, um das Herabfallen zu vermeiden.
z Sichern Sie sich mit Hilfe eines Sicherungsgrtels ab und tragen Sie einen
Schutzhelm.
z In Regionen mit niedrigen Temperaturen sollte wetterfeste, wrmende Kleidung
getragen werden.
-
7/29/2019 Compliance and Safety Manual.pdf
29/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 4 Sicherheitsinformationen
Huawei Technologies Proprietary
4-8
z Alle Hubgerte sollten vor Beginn der Arbeit auf ihre Funktionstchtigkeit
berprft werden.
4.4.1 Sicherheitshinweise fr die Benutzung von Leitern
Vergewissern Sie sich vor der Benutzung stets, dass die Leiter nicht beschdigt und
voll funktionstchtig ist. berladen Sie die Leiter nicht.
Der optimale Anlegewinkel fr eine Leiter liegt bei 75. Den Anlegewinkel knnen Sie
mit einem Winkelmesser oder mit den Armen messen. Beim Gebrauch der Leiter muss
deren Standfestigkeit zu jedem Zeitpunkt gewhrleistet sein. Das geffnete Ende der
Leiter muss deshalb fest und sicher auf dem Boden stehen. Der Boden sollte eine
glatte, regelmige Oberflche haben, um das Wackeln der Leiter zu verhindern.
Whrend des Aufstiegs darf der Schwerpunkt der Person nicht ber dem Leiterrand
liegen. Um die Sicherheit zu gewhrleisten und Unflle zu vermeiden, sollten sich stetsdrei Krperpunkte auf der Leiter befinden. Die Leiter sollte lediglich bis zur
vierthchsten Stufe bestiegen werden. Falls man auf eine erhhte Stelle, wie z. B. ein
Dach, steigen mchte, muss die Leiter 1m hher als die obere Kante sein.
4.4.2 Lastenaufzug
Warnung:Es ist verboten, sich unter dem Greifarm des Lastenaufzuges sowie unter den
hngenden Gegenstnden aufzuhalten.
z Das mit dem Lastenaufzug arbeitende Personal muss ausreichend geschult und
qualifiziert sein. Der Lastenaufzug muss regelmig auf seine
Funktionstchtigkeit berprft und gewartet werden. Benutzen Sie prgnante
Kommandos, um Missverstndnisse zu vermeiden.
z
Der Winkel, den das Aufzugskabel bildet, sollte maximal 90 sein. Ein grererWinkel kann zu einem Kabelbruch fhren.
-
7/29/2019 Compliance and Safety Manual.pdf
30/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 4 Sicherheitsinformationen
Huawei Technologies Proprietary
4-9
Figure 4-2 Lastenaufzug
4.5 Sonstiges4.5.1 Anheben schwerer Gegenstnde
Warnung:
Es ist verboten, unter einem angehobenen Gegenstand zu stehen oder durchzulaufen.
4.5.2 Scharfkantige Gegenstnde
Warnung:
Um sich vor Verletzungen zu schtzen drfen scharfkantige Gegenstnde nur mit
Schutzhandschuhen angefasst und transportiert warden .
-
7/29/2019 Compliance and Safety Manual.pdf
31/31
Compliance and Safety ManualHUAWEI MSOFTX3000 Mobile SoftSwitch Center Chapter 4 Sicherheitsinformationen
4.5.3 Einsteckplatinen
Anmerkung:
Beim Einstecken einer Platine darf kein zu groer Druck ausgebt werden, ansonsten
kann es zur Verdrehung der Kontakte kommen .
z Die Platine muss exakt lngs zum Einschub eingefhrt werden. Verhindern Sie,
dass sich die Schaltkreise der Platinen berhren. Das kann zu Kurzschluss oder
Kratzern auf der Platine fhren.
z Berhren Sie nicht mit den Fingern die Schaltkreise, Einzelkomponenten,
Verbindungen und Verbindungsschlitze.
4.5.4 Zusammenlegen von Signalleitungen
Anmerkung:
Signalleitungen sollten getrennt von Hochspannungsleitungen verlegt warden . Der
Abstand zwischen den Leitungen sollte mindestens 150mm betragen .