Complete Systems Kits - Home | MIL-SIM-FX Systems Complete Systems Kits MIL-FIL-SYS * Complete Fill...
Transcript of Complete Systems Kits - Home | MIL-SIM-FX Systems Complete Systems Kits MIL-FIL-SYS * Complete Fill...
Complete Systems
Complete SystemsKitsMIL-ECH-IMEESS* A complete training kit including an ECHO system which allows the user a multiple signature detonation with audio, visual effects and damage assessment * Includes high output LED strobes for night training * Can be converted to use as four separate units for daisy chaining * Includes NEW 27 MHz long range detonator (.5 Mile LOS) * Self InventoryingDescriptionECHO System IMEESS
MIL-MCO-IMEESS* A complete Mounted Convoy Operations training Kit * Kit includes a number of large tubes, heads, detonators and a supporting Field Supply Box with start up consumables * Includes 315 MHz 75mm E-Detonator (500 foot LOS) * Items to cover a large visual cue, required noise levels and damages assessment * Includes high output LED strobes for night training * Self-inventorying * Steel, powder coated casesDescriptionMounted Convoy Operations IMEESS
MIL-MCO-SCSA complete start up kit of consumables, service parts and spare parts for the MIL-MCO-IMEESS * Kit Includes: 1- skid grey FX Powder (Cool Smoke) (936 bottles per skid) 1- skid white Cool Smoke FX Powder (Cool Smoke) (936 bottles per skid) 2500 plastic burst discs 900 - 12gram CO2 cartridges CO2 Fill Station with 2 weigh scales, tools and spare parts 300 feet of airline in Orange, Tan and Olive Drab colors
Also incluces an assorted supply of airline connectors, repair kits, etc..DescriptionMCO IMEESS Support- Site Start up Kit
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –1
Complete Systems
Complete SystemsKitsMIL-URB-IMEESS* Urban Improvised Munitions Explosive Effects Simulator System * Comprised of devices that operate on the disposable CO2 cartridge and rubber burst disc platforms including a distraction device, pipe bombs and suicide vest simulators. * Contains a variety of detonators including radio controlled (315 Mhz), hard-wire via airline, hacksaw blades and auxiliary trigger. * Also included is a supporting Field Supply Box with start up consumables * Self-inventorying, steel, powder coated casesDescriptionUrban Training IMEESS
MIL-URB-SCS* A complete start-up kit of consumables, service parts and spare parts for the MIL-URB-IMEESS Kit * Kit Includes: 5 - Cases of Special FX White Powder 5 - Cases of Special FX Grey Powder 500 - Plastic Burst Discs 500 - Rubber Burst Discs 1200 - 12 gram CO2 cartridges 300 ft of assorted coloured Airline (Tan and Olive Drab) * An assorted supply of airline connectors, service tools, O-Rings etcDescriptionURB IMEESS Startup Kit
MIL-DD-KIT* Distraction Device Kit with consumables for 50 detonations * 10 Distraction Devices * 50 Disposable 12 Gram CO2 Cartridges * 50 Rubber Burst Discs * 1 Self inventorying steel powder coated carrying case.DescriptionDistraction Device Kit
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –2
Complete Systems
Complete SystemsKitsMIL-120-VBIED* VBIED simulator Kit Includes: 1 - ARC Head/Male Adapter 1 - 120mm Tube 1 - Base/Firing Actuator 1 - Airline 1 - Airline Clippers 1 - Trigger Command Detonator and 1 - Wooden CaseDescriptionVBIED Kit
MIL-E3-KIT* Includes a variety of interchangeable 2 inch diameter pipe bomb simulators * Radio controlled (315 MHz) detonation - 500 foot LOS * Two channel transmitter included * Machined aluminum, MIL SPEC hard anodized matte finish * Self-inventorying carry case * Start up consumablesDescriptionE3 Kit
MIL-SV1* Vest has marking rounds capability for damage assessment * Uses disposable 12 gram CO2 cartridges, plastic burst discs and FX Powder (Cool Smoke) * Includes 1 Trigger Command Detonator * Machined aluminum * MIL SPEC hard anodized matte finish * Polypropylene webbed harnessDescriptionSuicide Vest V1 Complete Kit
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –3
Complete Systems
Complete SystemsKitsMIL-SV42* A two tube suicide vest simulator complete kit * Tubes have blow forward (right angle) heads to direct powder away from user * Uses disposable 12 gram CO2 cartridges, rubber burst discs and FX Powder (Cool Smoke) * Includes 1 Trigger Command Detonator * Comes with X-Vest and 2 pouches.DescriptionSuicide Vest V4.2 Complete Kit
MIL-SV44* A four tube suicide vest simulator complete kit * Tubes have blow forward (right angle) heads to direct powder away from user * Uses disposable 12 gram CO2 cartridges, rubber burst discs and FX Powder (Cool Smoke) * Includes 1 Trigger Command Detonator * Comes with X-Vest and 4 pouchesDescriptionSuicide Vest V4.4 Complete Kit
MIL-SV4R* A four tube suicide vest simulator complete kit * Includes Remote Control Power Pack, E3 Universal Booby Trap Device, Ripcord and Trigger Command Detonator * Tubes have blow forward (right angle) heads to direct powder away from user * Uses disposable 12 gram CO2 cartridges, rubber burst discs and FX Powder (Cool Smoke) * Comes withX-Vest, 5 pouches and remote control box pouchDescriptionSuicide Vest V4.R Complete Kit
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –4
Complete Systems
Complete SystemsKitsMIL-FIL-SYS* Complete Fill Station System includes: 1 - Fill Station 1 - Vent Hose Muffler 1 - Vent Hose 2 - Weigh Scale 2 - Adapter Hose Assembly w/ Pin Depress 2 - Adapter w/ Pin Depress 1 - Fill Station Service Kit 1 - Package of 10 Pin Depress O-Rings 1 - Package of 5 Bulk Tank Washers 1 - Tube Silicone Lube 1 - 5/16" Allen Wrench 1 - Adjustable Wrench 10 - Rupture Discs 1 - Plastic Carrying CaseDescriptionFill Station Complete Start up Kit
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –5
Detonators
DetonatorsHardwire via Airline MIL-12G-TCD* Detonates any MIL-SIM-FX device * Uses disposable 12 gram cartridge for initiation * Command detonation * Standard issue with suicide vest * Cast and machined plasticDescriptionTrigger Command Detonator
MIL-12G-MFD* Detonates any MIL-SIM-FX device * Uses disposable 12 gram cartridge for initiation * Tripwire, Command, Pressure sensitive capabilities * Machined aluminum * MIL SPEC anodized matte finishDescriptionMulti-Function Detonator
MIL-12G-DMS* Pressure Release Detonator * Uses disposable 12 gram cartridge for initiation * Machined aluminum * MIL SPEC anodized matte finishDescriptionDead Man’s Switch - Pressure Release Detonator
MIL-12G-PAD* Pressure Applied Detonator * 10lb pressure applied detonation * Uses disposable 12 gram cartridge for initiation * Machined aluminum * MIL SPEC anodized matte finishDescriptionPressure Applied Detonator
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –6
Detonators
DetonatorsRadio ControlledMIL-E3-EFD* E3 Electronic Firing Device * Streamlines the functions of MIL-EIPB-EOD, MIL-RX-EFD and MIL-RX-IED into one device * 2 Channel remote control power pack * Tripwire capabilities * External trigger banana jacks * 315 MHz and 500ft LOSDescriptionElectronic Firing Device
MIL-RX-75SK* Single Air Solenoid Trigger and Compressed Air Chamber Set * Radio controlled detonator with 2 Channel Transmitter * 315 MHz - 500 Feet LOS * Allows for two consecutive detonations * Uses low pressure compressed air for initiation * Machined aluminum * MIL SPEC anodized matte finishDescription75mm E-Detonator
MIL-4CH-RXASK* ECHO Long Range 4 Channel Receiver * Compressed Air Chamber with Sure Seal Connectors * 5 Pin Connector Harness * External Trigger Inputs-Initiate or cut an improvised firing circuit to trigger detonation * 4 Channel LED Status Indicators, Battery Status Test Button, On/Off Switch with LED Status Indicator * 4 Channel/Button Hand Held Transmitter * Includes Quick Fill Trigger * Storage Case * 27 MHz and .5 Mile LOSDescriptionRadio Controlled 4 Channel Extended Range DetonatorMIL-4CH-RXAS* ECHO Long Range 4 Channel Receiver and Transmitter with 5 Pin Connector * 27 MHz - .5 Mile LOS * 4 Channel/Button Hand Held Transmitter * With Normally Open/Normally Closed firing circuit Compressed Air Chamber - Sold SeparatelyDescriptionECHO Long Range Detonator
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –7
Dismounted Training Devices
Dismounted Training DevicesExternal Detonation DevicesMIL-5-105* Improvised ordnance round for detection / reaction drills * Anti-personnel training * Uses disposable 12 gram CO2 cartridge and FX Powder (Cool Smoke) * Machined aluminum * MIL SPEC anodized matte finishDescription105mm IED Threat SIM with 5 inch Tube
MIL-5-BMB* An improvised bomb for detection / reaction drills * Anti-personnel training * Uses disposable 12 gram CO2 cartridge and FX Powder (Cool Smoke) * Machined aluminum * MIL SPEC anodized matte finish.DescriptionBomb IED Threat SIM with 5 inch Tube
MIL-5-DCP* Anti-personnel or convoy training * Uses disposable 12 gram CO2 cartridge and FX Powder (Cool Smoke) * Machined aluminum * MIL SPEC anodized matte finish * Has marking rounds capability for damage assessmentDescriptionDirectional Charge IED Threat SIM with 5 inch Tube
MIL-5-EFP* Explosively Formed Penetrator Simulator Assembly * Specifically designed to be used with marking rounds * 42” marking zone at approximately 25 feet * MIL SPEC anodized matte finishDescriptionExplosively Formed Penetrator Assembly with 5 inch Tube
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –8
Dismounted Training Devices
Dismounted Training DevicesExternal Detonation DevicesMIL-5-MTR* Improvised mortar round for detection/reaction drills * Anti-personnel training * Uses disposable 12 gram CO2 cartridge and F/X powder * Machined aluminum * MIL SPEC anodized matte finishDescriptionMortar IED Threat with 5 inch Tube
MIL-5-NCA* Improvised ordnance round with nose cone firing actuator for detection / reaction drills * Anti-personnel training * Uses disposable 12 gram CO2 cartridge and F/X powder * Machined aluminum * MIL SPEC anodized matte finishDescriptionDet Cord to Nose Cone IED with 5 inch Tube
MIL-5-RAH* Uses disposable 12 gram CO2 cartridge and F/X powder * Anti-personnel training * Machined aluminum * MIL SPEC anodized matte finish * Has marking rounds capability for damage assessmentDescriptionA.R.C Threat SIM with 5 inch Tube
MIL-5-UXO* Replica mortar round for detection / reaction drills * Anti-personnel training * Uses disposable 12 gram CO2 cartridge and F/X powder * Machined aluminum * MIL SPEC anodized matte finishDescriptionMortar UXO Trainer with 5 inch Tube
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –9
Dismounted Training Devices
Dismounted Training DevicesExternal Detonation DevicesMIL-PB-RAH* A short pipe bomb simulator * Requires external detonation device * Uses rubber burst discs * Uses FX Powder (Cool Smoke) * Machined aluminum * MIL SPEC anodized matte finishDescriptionPipe Bomb Tube with Right Angle Head
MIL-PBST-S* A short pipe bomb simulator * Requires external detonation device * Uses rubber burst discs * Uses FX Powder (Cool Smoke) * Machined aluminum * MIL SPEC anodized clear coat finishDescriptionPipe Bomb SIM Tube (Short)
MIL-RB-SQB* A small explosion simulator * Requires an external detonation device * Magnetic bottom * Uses rubber burst discsDescriptionMagnetic Squib
Internal Detonation DevicesMIL-DD-SIM* Distraction Device Simulator * Uses disposable 12 gram CO2 cartridge * Creates an audible report * Used for dynamic entry training * Aluminum body with MIL SPEC anodized matte finishDescriptionDistraction Device Simulator
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –10
Dismounted Training Devices
Dismounted Training DevicesInternal Detonation DevicesMIL-DD-SIM2* Distraction Device Simulator with Powder Cavity for Visual Effect * Uses disposable 12 gram CO2 cartridge * Creates an audible and visible report * Used for dynamic entry training * Aluminum body with MIL SPEC anodized matte finishDescriptionDistraction Device Simulator with Powder Cavity
MIL-DMS-IED* Low Profile - Pressure Release Detonation * Uses disposable 12 gram CO2 cartridge * Creates an audible report * Aluminum body with MIL SPEC anodized matte finishDescriptionDead Man Switch Improvised Explosive Device Simulator
MIL-LM* Equipped with 6 drain holes which prevent water build up inside the head during extended deployment * Uses disposable 12 gram CO2 cartridge, Plastic Burst Disc and FX Powder (Cool Smoke) * Can be quickly converted from pressure applied to pressure release by changing the pierce pin plug (included). * Includes plug removal toolDescriptionLandmine
MIL-LM-TC6* TC/6 Anti-Tank Mine Simulator * MIL-LM uses disposable 12 gram CO2 cartridge, Plastic Burst Disc and FX Powder (Cool Smoke) * Can be quickly converted from pressure applied to pressure release by changing the pierce pin plug (included). * Includes plug removal tool DescriptionTC6 Anti-Tank Mine Simulator
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –11
Dismounted Training Devices
Dismounted Training DevicesInternal Detonation DevicesMIL-PB-TW*A single Trip Wire Pipe Bomb simulator * Internal Detonation * Uses rubber burst discs * Uses FX Powder (Cool Smoke) * Machined aluminum * MIL SPEC anodized matte finishDescriptionTripwire Initiated Pipe Bomb
MIL-PB-TWS* Two Trip Wire Pipe Bomb Simulators in Magnetic Caddy * Internal Detonation * Uses rubber burst discs and FX Powder (Cool Smoke) * Machined aluminum * MIL SPEC anodized matte finishDescriptionTripwire Initiated Pipe Bomb Set
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –12
Mounted Training Devices
Mounted Training DevicesE4 FamilyMIL-E4* Designed for rugged training conditions, the streamlined E4 combines MIL-SIM-FX's Firing Actuator, Compressed Air Chamber and IED effect simulator in one compact buriable device. * 60 inch bare wire leadsDescriptionElectrically Initiated Buriable Device- with Bare Wire Leads
MIL-E4-1* Designed for rugged training conditions, the streamlined E4-1 combines MIL-SIM-FX's Firing Actuator Compressed Air Chamber and IED effect simulator in one compact buriable device. * 60 inch banana plug leadsDescriptionElectrically Initiated Buriable Device- with Banana Plugs Leads
ECHO SystemMIL-ECHO-1* ECHO System with built in ILLUM-FX for night training * Includes: 4 - ECHO Devices (heads sold separately) 1 - 4 Solenoid Compressed Air Chamber with 5 pin connector 1 - 5 Cell Caddy 2 - Ground Stakes DescriptionECHO System
External Detonation DevicesMIL-120-DCP8* Includes 2 - 8 Inch Ground Stakes * Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 44 oz) * Machined aluminum * MIL SPEC anodized matte finish * Has marking rounds capability for damage assessment
DescriptionDirectional Charge with 120 mm Tube
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –13
Mounted Training Devices
Mounted Training DevicesExternal Detonation DevicesMIL-20-105* Improvised ordnance round for detection / reaction drills * Mounted or dismounted convoy training * Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz) * Machined aluminum * MIL SPEC anodized matte finish Description105mm IED Threat SIM with 20 inch Tube
MIL-20-BMB* Improvised bomb for detection / reaction drills * Mounted or dismounted convoy training * Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz) * Machined aluminum * MIL SPEC anodized matte finishDescriptionBomb IED Threat SIM with 20 inch Tube
MIL-20-CBA* Non-directional concussive effects device used to achieve a significant audio signature * Consumable platform used is P.E.T. beverage (pop/soda) bottles * Machined aluminum * MIL SPEC anodized matte finish DescriptionConcussive FX IED Threat SIM with 20 inch Tube
MIL-20-DCP6* Mounted or dismounted convoy training device * Includes 2 - 6 Inch Ground Stakes * Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz) * Machined aluminum * MIL SPEC anodized matte finish * Has marking rounds capability for damage assessmentDescriptionTC6 Anti-tank Mine Simulator
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –14
Mounted Training Devices
Mounted Training DevicesExternal Detonation DevicesMIL-20-DCP8* Mounted or dismounted convoy training device * Includes 2 - 8 Inch Ground Stakes * Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz) * Machined aluminum * MIL SPEC anodized matte finish * Has marking rounds capability for damage assessmentDescriptionDirectional Charge with 20 inch Tube
MIL-20-FHA* IED Threat Simulator with 180 degree Spray pattern * Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz) * Machined aluminum * MIL SPEC anodized matte finishDescriptionIED Threat SIM- 180 Degree with 20 inch Tube
MIL-20-MTR* Improvised mortar for detection / reaction drills * Mounted or dismounted convoy training * Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz) * Machined aluminum * MIL SPEC anodized matte finish DescriptionMortar IED Threat SIM with 20 inch Tube
MIL-20-NCA* Improvised ordnance round with nose cone firing actuator for detection / reaction drills * Mounted or dismounted convoy training * Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz) * Machined aluminum * MIL SPEC anodized matte finishDescriptionDet Cord to Nose Cone IED with 20 inch Tube
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –15
Mounted Training Devices
Mounted Training DevicesExternal Detonation DevicesMIL-20-RAH* Improvised claymore for detection / reaction drills * Has marking rounds capability for damage assessment * Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz) * Machined aluminum * MIL SPEC anodized matte finishDescriptionIED Threat SIM with 20 inch Tube
MIL-20-UXO* Replica mortar round for detection / reaction drills * Mounted or dismounted convoy training * Uses refillable High Pressure Bottles and FX Powder (Cool Smoke) (up to 22 oz) * Machined aluminum * MIL SPEC anodized matte finishDescriptionMortar UXO Trainer with 20 inch Tube
Improvised Mortar SimulatorsMIL-MTR-DFLTAS* Improvised Mortar Round Launch Tube and Base Set * Drop Fired Mortars * Includes: 1 - Launch Tube 1 - Base Assembly 8 - Drop Fired Rounds 1 - Carrying CaseDescriptionImprovised Mortar System - Drop Fired
MIL-MTR-RFLTAS* Improvised Mortar Round Launch Tube and Base Set * Remote Fired Mortar * Includes: 1 - Launch Tube 1 - Base Assembly 1 - Remote Fired RoundDescriptionImprovised Mortar System - Remote FiredPH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –16
Mounted Training Devices
Mounted Training DevicesImprovised Mortar SimulatorsMIL-MTR-RFLTS* Improvised Mortar Round Launch Tube System * Remote Fired Mortar * Includes: 1- Launch Tube 1- Remote Fired RoundDescriptionImprovised Mortar Round
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –17
Refillable Bottles
Refillable BottlesC02 Bottles and HPA BottlesMIL-35-HPN* Refillable high pressure bottle with high flow valve * Includes magnetic thread/pin protector cap * Light weight alloy steel cylinder * Machined brassDescription35 Cubic Inch - 1800 PSI High Pressure Bottle
MIL-9R-HFV* Refillable high pressure bottle with high flow valve * Includes magnetic thread/pin protector cap * Light weight alloy steel cylinder * Machined brass DescriptionHigh Pressure Bottle with High Flow Valve
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –18
Inert
InertInert Training DevicesMIL-155-ICAR* Inert training round * Light weight aluminum cast * Olive drab powder coat finishDescription155mm Inert Cast Aluminum Rounds
MIL-155-PET* Works with Non-Directional Concussive FX System * Window adds shape charge directional capability when detonating PET bottles * Light weight aluminum cast * Olive drab powder coat finishDescription150mm Concussive FX VISMOD
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –19
Consumables
ConsumablesAirlineMIL-GRN-100* Green airline used to connect detonator with device * Par flex 1/8 O.D. x .031 wall nylon 500 WP lineDescriptionOlive Drab Airline
MIL-ORG-100* Orange airline used to connect detonator with device * Par flex 1/8 O.D. x .031 wall nylon 500 WP lineDescriptionOrange Airline
MIL-TAN-100* Tan airline used to connect detonator with device * Par flex 1/8 O.D. x .031 wall nylon 500 WP lineDescriptionTan Airline
Burst DiscsMIL-PBD-2500* Case of 2500 Plastic burst discs * Molded plasticDescriptionPlastic Burst Discs
MIL-RBD-500* Bag of 500 rubber burst discs * Bulk purchase pricingDescriptionRuber Burst Discs
MIL-RBD-1000* Case of 1000 rubber burst discs * Bulk purchase pricingDescriptionRubber Burst Discs
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –20
Consumables
ConsumablesBurst DiscsMIL-GBD-250* Bag of 250 thermoplastic burst discs * Fragment free * Considerably louder than the standard black rubber burst discDescriptionThermoplastic Burst Disc - Green
PET BottlesMIL-PET-500* 500 ML PET (Polyethylene Terephthalate) plastic bottle * Used with the Concussive FX Bottle Adapter , Concussive FX IED Threat SIM and the CFX System * New, Non-Recycled Plastic * RecyclableDescriptionPET Plastic Bottle
C02 CartridgesMIL-C02-300* Case of 300 cartridges * 12 gram liquid CO2 * Disposable formed plated steel cartridge * Authorized for use with MIL-SIM-FX productsDescriptionDisposable CO2 Cartridges
PowderMIL-GRY-CS* Grey FX Powder (Cool Smoke) used to simulate the visual cloud effect of an explosion * Ground Talc Powder * Case of 12 - 22 oz bottlesDescriptionCool Smoke - Special FX Powder- Grey
MIL-GRY-SKD* Grey FX Powder (Cool Smoke) used to simulate the visual cloud effect of an explosion * Non-scented ground talc powder * Skid of 78 cases (936 - 22 oz bottles)DescriptionCool Smoke - Special FX Powder- Grey
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –21
Consumables
ConsumablesPowderMIL-WHT-CS* White FX Powder (Cool Smoke) used to simulate the visual cloud effect of an explosion * Ground Talc Powder * Case of 12 - 22 oz bottlesDescriptionCool Smoke - Special FX Powder- White
MIL-WHT-SKD* White FX Powder (Cool Smoke) used to simulate the visual cloud effect of an explosion * Non-scented ground talc powder * Skid of 78 cases (936 - 22 oz bottles)DescriptionCool Smoke - Special FX Powder- White
Marking RoundsMIL-68-FO*Yellow Marking rounds used in some of the MIL-SIM-FX IED devices * Gel cap filled with non-toxic, non staining paint filler DescriptionFluorescent Orange Color Paint Pallets
MIL-68-FY* Orange Marking rounds used in some of the MIL-SIM-FX IED devices * Gel cap filled with non-toxic, non staining paint filler DescriptionFluorescent Yellow Color Paint Pallets
Dry LubricantMIL-PTFE* Dry lubricant used for lubing the threads of the MIL-SIM-FX IED devices * Contains - Hexane, Propanone, Propane/isobutane/w-butane blend, Toluene, TetrafluroethyleneDescriptionPTFE Dry Lubricant
MIL-PTFE-CS* Case of 12 * Dry lubricant used for lubing the threads of the MIL-SIM-FX IED devices * Contains - Hexane, Propanone, Propane/isobutane/w-butane blend, Toluene, TetrafluroethyleneDescriptionPTFE Dry Lubricant - Case of Twelve
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –22
75mm EDet Support Items
75mm EDet Support Items75mm EDet SupportMIL-75S-BJS* Replacement Banana Jacks for the MIL-RX-75 * Set of Two - One Black, One Red * Flush fitting - won't snap off * Plastic DescriptionFlush Fitting Banana Jack Set (Black/Red)
MIL-BP-4S* Set of four red and four black banana plugsDescriptionSet of Banana Plugs
MIL-75S-CCA* Circuit Card ReplacementDescription75mm E-Detonator Circuit Card Assembly
MIL-GAUGE-160PSI* 160 PSI pressure custom gauge * Color coded to identify minimum and maximum operating pressures * Polycarbonate window, stainless steel construction
DescriptionPressure Gauge
MIL-RX-75* Radio controlled (315Mhz) detonation (100m LOS) * Initiate any 12 volt device * Two channel transmitter included * Machined aluminum * MIL SPEC hard anodized matte finishDescription2 Channel Radio Controlled Receiver (315 MHz)
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –23
75mm EDet Support Items
75mm EDet Support Items75mm EDet SupportMIL-EC-ET* Replacement End Cap for the MIL-RX-75 * Machined aluminum * MIL SPEC hard anodized matte Clear Coat finishDescription2 Channel Radio Receiver (315 MHz) End Cap with Wiring Harness
MIL-EC-ETCB*Replacement End Cap and Circuit Board for the MIL-RX-75 * Includes circuit board * Machined aluminum * MIL SPEC hard anodized matte Clear Coat finish Description2 Channel Radio Controlled Receiver (315 MHz) End Cap with Wiring Harness and Circuit Board
MIL-ILLUM-FX* High output LED strobe for night training * 2 LED lights mounted on a steel powder coated base with magnetic feetDescriptionIllumination FX- High Output LED Strobe
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –24
Airline Support Items
Airline Support ItemsAirline Support ItemsMIL-01-AC* Airline clippers with lanyard * Plastic, mould with stainless steel cutting bladeDescriptionAirline Clippers
MIL-18-1032-ACK* Package of 10 - 1/8" x 10/32" airline connectors * Push lock connection * Plated brass with nylon partDescriptionAirline Connectors 1/8 x 10/32
MIL-18-18-ACO* Package of 10 stainless steel airline connectors * All stainless steel construction DescriptionSteel Collar Airline Connectors 1/8 x 1/8
MIL-18-18-KIT* 100 Steel Airline Connectors * 5 Collar Unlock Tools * Plasma cut C10-18 hot rolled mild steel wrench with blue powder coat finish * 1/8 X 1/8" Stainless steel airline connectors DescriptionAirline Connector/Tool Kit
MIL-18-AC10K* Package of 10 - 1/8" x 1/8" standard airline connectors * Push lock connection * Plated brass with nylon part DescriptionAirline Connector 1/8 X 1/8
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –25
Airline Support Items
Airline Support ItemsAirline Support ItemsMIL-18-AECK* Package of 5 - 90 degree airline connectors * Plated brass with nylon partDescriptionAirline "Elbow" Connector Kit
MIL-18-AJK* Package of 5 airline connectors used for joining two airlines together * Plated brass with nylon partDescriptionAirline Junction Kit
MIL-18-ATCK* A package of 5 - "T" airline connectors used for daisy chaining two or more devices together * Plated brass with nylon partDescriptionAirline "T" Connector Kit
MIL-4-WAY* Airline fitting used for daisy chain detonations when activating up to 4 individual devicesDescriptionDaisy Chain Fitting
MIL-AC-COMBO* A steel combination wrench to remove airline and airline connectors * Plasma cut C10-18 hot rolled steel * Blue powder coat finish DescriptionCombination Collar Unlock Tool and 1/2 inch Wrench
MIL-AC-DBGK* Package of 10 airline connector protectors * Rubber device used to protect the airline connectors of the MIL-SIM-FX devices * High temperature silicone rubber DescriptionAirline Connector Dust Boots
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –26
Bases
BasesBasesMIL-12G-SB* A base for any 12 gram Firing actuator * Includes 12 gram CO2 Cartridge Housing * Machined aluminum * MIL SPEC hard anodized matte finishDescription12 Gram Cartridge Base
MIL-9R-SB* A base for any 9oz firing actuator * Machined aluminum * MIL SPEC hard anodized matte finishDescription9 Ounce Tank Base
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –27
Basic Tools
Basic ToolsBasic ToolsMIL-1B-SWS* Single High Quality Strap Wrench * Molded plastic and rubber DescriptionHigh Quality Strap Wrench
MIL-2-SWS* A set of Good Quality Strap Wrenches * Molded plastic and rubber DescriptionStrap Wrench Set
MIL-38T-AW* 3/8" T-handle Allen wrench * Treated, forged steel alloy toolDescription3/8 inch T-Handle Allen Wrench
MIL-532T-AW* 5/32" T-handle Allen Wrench * Treated, forged steel alloy toolDescription5/32 inch T-Handle Allen Wrench
MIL-516T-AW * 5/16" T-Handle Allen Wrench used to service the CO2 Fill Station * Forged steel
Description5/16 inch T-Handle Allen Wrench
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –28
Basic Tools
Basic ToolsBasic ToolsMIL-EFD-RTK* Tool kit for repairing/servicing the MIL-RX-EFD * Includes: 1 - 7/16" T-Handle Allen Wrench 1 - 5/32" T-Handle Allen Wrench 1 - Pair of Soft Jaw PliersDescriptionEFD Repair Tool Kit
MIL-FSW* Fill Station Wrench * Used to attach/remove valve to tank * Steel powder coated DescriptionFill Station Wrench
MIL-12-AW* 12" Adjustable WrenchDescriptionAdjustable Wrench
MIL-THN-D* Used to remove SS Fasteners from the 5 cell caddy * Also used to remove airline connectors * A steel ½" x 6" point socket T-Handle wrench * Powder-coated blue DescriptionT-handle Nut Driver
MIL-SPN* Measuring spoon for measuring FX Powder (Cool Smoke) * Stainless Steel DescriptionMeasuring Spoon
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –29
Basic Tools
Basic ToolsBasic ToolsMIL-6-SJS* Magnetic Soft Jaws for Vice Grip * Rubber pads prevent damage to any of products when using a bench vice grip * Magnetic so they stay in placeDescriptionSoft Jaw Set
MIL-SO-TWS* Inch pound torque wrench used for servicing High Flow Valves * Includes 6 point - 3/8" drive * High grade stainless tooling steel DescriptionDial Torque Wrench with Drive Socket
MIL-375-6PT* 3/8" x 3/8" Socket-6 Point- 3/8" drive * Replacement socket for the MILSO-TWSDescription6 Point Socket
MIL-BPH* Ball Peen Hammer used to service High Flow Valve bottleDescriptionBall Peen Hammer
MIL-HFV-BP* Brass Punch used to service High Flow Valve bottleDescriptionBrass Punch
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –30
C02 and HPA Bottle Support Items
C02 and HPA Bottle Support ItemsC02 and HPA Bottle Support ItemsMIL-41010-ORK* Package of 10 * Urethane O-Rings used on the High Pressure Bottle, ECHO Set Plug and ECHO Firing IndicatorDescriptionUrethane O-ring
MIL-BTL-CAP* High Pressure Bottle valve thread protector cap * Blue aluminum cap DescriptionValve Cap (Blue Aluminum)
MIL-HFV-MEC* HFV bottle thread/pin protector cap * Magnetic * Machined aluminum, olive drab anodized finishDescriptionGreen Magnetic Bottle Valve Cap
MIL-LIQ-MEC* HFV bottle thread/pin protector cap * Magnetic * Machined aluminum, light blue anodized finish DescriptionBlue Magnetic Bottle Valve Cap
MIL-HFV-RDK* Package of 10 replaceable rupture disc for the 9oz CO2 tank high flow valve * Machined brass, copper insertDescriptionTank Rupture Discs
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –31
C02 and HPA Bottle Support Items
C02 and HPA Bottle Support ItemsC02 and HPA Bottle Support ItemsMIL-SO-TWS* Inch pound torque wrench used for servicing High Flow Valves * Includes 6 point - 3/8" drive * High grade stainless tooling steel DescriptionDial Torque Wrench with Drive Socket
MIL-375-6PT* 3/8" x 3/8" Socket-6 Point- 3/8" drive * Replacement socket for the MILSO-TWSDescription6 Point Socket
MIL-BPH* Ball Peen Hammer used to service High Flow Valve bottleDescriptionBall Peen Hammer
MIL-HFV-BP* Brass Punch used to service High Flow Valve bottleDescriptionBrass Punch
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –32
Caddies and Cases
Caddies and CasesCaddiesMIL-2-CC* A two holster caddy used for the 75mm E-Detonator * 3" Diameter Cells * Steel powder coated greenDescription3 inch Cell Caddy
MIL-2-CC2* A two holster caddy with magnetic feet * 2" Diameter Cells * Steel powder coated green Description2 inch Cell Caddy
MIL-5-CC* Five Cell Caddy * Powder coated steelDescriptionFive Cell Caddy
MIL-75S-RB* Replacement rubber bumper * Includes Washer and ScrewDescriptionRubber Bumper
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –33
Caddies and Cases
Caddies and CasesCasesMIL-15-TC* A wooden case used for carrying 15 CO2 tanks * ¾" pressure treated wood * Green all weather stain * Plated steel carry handlesDescriptionCO2 Tank Case
MIL-08-SC* A wooden case used for carrying 8 20inch MIL-SIM-FX tubes * ¾" pressure treated wood * Green all weather stain * Plated steel carry handlesDescriptionEight Pocket Case
MIL-120-SPC* A wooden case used for carrying one 120mm MIL-SIM-FX tube * ¾" pressure treated wood * Green all weather stain * Plated steel carry handles DescriptionSingle 120mm Case
MIL-120-DPC* A wooden case used for carrying two 120mm MIL-SIM-FX tubes * 3/4" pressure treated wood * Grenn all weather stain * Plated steel carrying handlesDescriptionDouble 120mm Case
MIL-FSB-S* Used for MIL-SV1; MIL-SV22;MIL-SV24; MIL-SV32, MIL-SV34; and MIL-75S * PlasticDescriptionSmall Field Supply Box
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –34
Caddies and Cases
Caddies and CasesCasesMIL-FSB-M* Used for MIL-RD-KIT, MIL-FIL-SYS, and MIL-ECH-RX4 * Plastic DescriptionMedium Field Supply Box
MIL-FSB-L* Used for MIL-ECH-RXL4, MIL-RXL-1CHS, MIL-RXL-4CHS * Plastic DescriptionLarge Field Supply Box
MIL-IMEESS* A case used for carrying the MIL-SIM-FX devices. * Hot rolled mild steel * Spot welded and full weld construction * Green powder coat finish * Dense ULB charcoal ester foam inserts DescriptionIMEESS Case- Metal with Custom Foam Insert
MIL-FSB* A case used for carrying the items that support the MIL-SIM-FX devices * Hot rolled mild steel * Spot welded and full weld construction * Green powder coat finish DescriptionSteel Field Supply Box
MIL-UDO-CS* Urban Dismounted Operations Case * Custom cut foam insert * Hot rolled mild steel * Spot welded and full weld construction * Green powder coat finish
DescriptionUDO Case
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –35
Caddies and Cases
Caddies and CasesCasesMIL-UDOX-CS* Urban Dismounted Operations with Extended Capabilities Case * Custom cut foam insert * Hot rolled mild steel * Spot welded and full weld construction * Green powder coat finish DescriptionUDOX Case
MIL-DD-BX* A case for used for carrying 10 MIL-DD-SIM as well as support items * Hot rolled mild steel * Spot welded and full weld construction * Green powder coat finishDescriptionDistraction Device Box
MIL-SP-OB* Organizer Box for service parts * Plastic DescriptionService Parts Organizer Box
MIL-SP-OBS* Small Organizer Box for service parts * Plastic DescriptionSmall Service Parts Organizer Box
MIL-12G-CT* A tray that holds disposable 12 gram CO2 cartridges * Holds up to 50 cartridges * Plastic Description12 gram CO2 Cartridge Tray
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –36
Caddies and Cases
Caddies and CasesCasesMIL-MCO-GSS* Set of Two * Replacement Gas Struts for the Large IMEESS CaseDescriptionGas Spring Strut for the MCO-IMEESS Case
MIL-UDOX-GSS* Set of Two * Replacement Gas Struts for the Small IMEESS Case DescriptionGas Spring Strut for the UDO-IMEESS Case
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –37
Compressed Air Chamber / Solenoid Support Items
Compressed Air Chamber / Solenoid Support ItemsCompressed Air Chamber/Air-Solenoid TriggerMIL-CH-ASK* Replacement solenoid kit for the MIL-RX-75S * Kit includes: 1 Solenoid/wiring harness/banana jacks, 2 Screws, 1 O-Ring, 1 Airline Connector, 1 Blue Thread Locker Capsule * 14 inch leadDescriptionShort Leads with Banana Plugs
MIL-1SOL-KIT* Replacement solenoid kit for the Compressed Air Chamber * Kit includes: 1 Solenoid/wiring harness/banana jacks, 2 Screws, 1 O-Ring, 1 Airline Connector, 1 Blue Thread Locker Capsule * 60 inch lead DescriptionLong Leads with Banana Plugs
MIL-SV2-AT* Two Air-Solenoid Trigger/Compressed Air Chamber with Banana Plugs * Detonates any MIL-SIM-FX device * Initiated by any 12 volt .5 amp output * Uses low pressure (100 psi) CO2 or compressed air for initiation * Includes pressure gauge and fill valve * Machined aluminum * MIL SPEC anodized matte finish DescriptionTwo Air-Solenoid Compressed Air Chamber
MIL-SV4-AT* Four Air-Solenoid Trigger/Compressed Air Chamber with Banana Plugs * Detonates any MIL-SIM-FX device * Initiated by any 12 volt .5 amp output * Uses low pressure (100 psi) CO2 or compressed air for initiation * Includes pressure gauge and fill valve * Machined aluminum * MIL SPEC anodized matte finishDescriptionFour Air-Solenoid Compressed Air Chamber
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –38
Compressed Air Chamber / Solenoid Support Items
Compressed Air Chamber / Solenoid Support ItemsCompressed Air Chamber/Air-Solenoid TriggerMIL-EC-SSA* Single Solenoid Head Assembly * New style solenoids (Contact your sales representative if you are uncertain if your existing product uses the new style solenoids)DescriptionSingle Solenoid Head Assembly
MIL-EC-DSA* Dual Solenoid Head Assembly * New style solenoids (Contact your sales representative if you are uncertain if your existing product uses the new style solenoids)DescriptionDual Solenoid Head Assembly
MIL-EC-FG* Replacement part for the compressed air chamber * Includes: End Cap, Gauge, Fill Valve and Fill Valve Cap * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionCompressed Air Chamber End Cap
MIL-GAUGE-160PSI* 160 PSI pressure custom gauge * Color coded to identify minimum and maximum operating pressures * Polycarbonate window, stainless steel constructionDescription160 PSI Gauge
MIL-FVC2* Replacement Fill Valve Cap with Tether * Threadless Pliable Rubber Cap DescriptionFill Valve Cap with Tether
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –39
Compressed Air Chamber / Solenoid Support Items
Compressed Air Chamber / Solenoid Support ItemsCompressed Air Chamber/Air-Solenoid TriggerMIL-SOL-BLUK* Solenoid Kit with sure seal connectors, blue shrink wrap, O-Ring, screws loctite and silicone capsuleDescriptionBlue Lead Solenoid with Sure Seal Connector
MIL-SOL-GRNK* Solenoid Kit with sure seal connectors, green shrink wrap, O-Ring, screws loctite and silicone capsuleDescriptionGreen Lead Solenoid with Sure Seal Connector
MIL-SOL-REDK* Solenoid Kit with sure seal connectors, red shrink wrap, O-Ring, screws loctite and silicone capsuleDescriptionRed Lead Solenoid with Sure Seal Connector
MIL-SOL-YELK* Solenoid Kit with sure seal connectors, yellow shrink wrap, O-Ring, screws loctite and silicone capsuleDescriptionYellow Lead Solenoid with Sure Seal Connector
MIL-SV4-AT2* Four Air-Solenoid Trigger with Sure Seal Connectors * Wiring harness (sold separately) is available with 5 pin connector orbanana plugs * Initiated by any 12 volt .5 amp output * Uses low pressure (100 psi) CO2 or compressed air for initiation * Includes pressure gauge and fill valve * Machined aluminum * MIL SPEC anodized matte finishDescriptionFour Solenoid Compressed Air Chamber with Sure Seal Connectors
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –40
Compressed Air Chamber / Solenoid Support Items
Compressed Air Chamber / Solenoid Support ItemsCompressed Air Chamber/Air-Solenoid TriggerMIL-ECH-WHB* Color coded wiring harness for the Four Solenoid Compressed Air Chamber * Banana Plug Leads * Sure Seal connectors * Four solenoid connectors, two ECHO illum-fx connectorsDescriptionSure Seal Connector Wiring Harness with Banana Plugs
MIL-ECH-WHSC* Color coded wiring harness for the Four Solenoid Compressed Air Chamber * Single (5 Pin ) Lead * Sure Seal connectors * Four solenoid connectors, Two ECHO Illum-Fx connectorsDescriptionSure Seal Connector Wiring Harness with 5 Pin Connector
MIL-TSK* Package of 10 Test/Tether Shunt * Looped end fits under the airline connector to prevent loss of the shunt * Plastic DescriptionTether Shunt
MIL-TST-K* Package of 10 Tether ShuntsDescriptionTest Shunt
MIL-12G-QFT* Used for filling Compressed Air Chambers * Uses disposable 12 gram cartridges * Brass and machined plastic DescriptionQuick Fill Trigger
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –41
Compressed Air Chamber / Solenoid Support Items
Compressed Air Chamber / Solenoid Support ItemsCompressed Air Chamber/Air-Solenoid TriggerMIL-12G-QFTK* Converts existing MIL-12G-FVA to MIL-12G-QFTDescriptionQuick Fill Trigger Upgrade Kit
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –42
Distraction Device Support Items
Distraction Device Support ItemsDistraction Device Support ItemsMIL-DD-012* Package of 5 O-Rings used with MIL-DD-SIM Inner PistonInner Piston O-Ring Kit
MIL-DD-015* Package of 5 O-Rings used with MIL-DD-SIM Outer PistonDescriptionOuter Piston O-Ring Kit
MIL-DD-129* Package of 5 O-Rings used with MIL-DD-SIM CO2 Cartridge HousingDescriptionCO2 Cartridge Housing O-Ring Kit
MIL-DD7-KIT* Repair kit for the MIL-DD-SIM * Includes 1 Outer Piston and 1 Inner PistonDescriptionDistraction Device Repair Kit
MIL-DD-PIN* Safety Pin replacement part for the MIL-DD-SIM * Quick release pin with spring loaded ball * Stainless steel DescriptionSafety Pin
MIL-PPS-10* Package of 10 Pierce Pin seals for DD-SIMDescriptionPierce Pin Seal
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –43
E3 Family Support Items
E3 Family Support ItemsE3 FamilyMIL-E3-RXPP* Radio controlled 2 channel power supply * 2 channel, 315 MHz - 500 foot LOS * Timer, crush wire, pressure plate and tilt switch capabilities * Aluminum with MIL SPEC anodized matte finishDescriptionRX 2 Channel- Power Pack
MIL-E3-PP* Power supply used for improvised detonation control with the buriable E3 system * Timer, crush wire, pressure plate and tilt switch capabilities * Aluminum with MIL SPEC anodized matte finishDescription9 Volt Battery Power Pack
MIL-E3-BPH* E3 powering device * Electronically initiated * Uses E3 head attachments * Designed for extreme conditions (wet, dusty or buried) * Aluminum with MIL SPEC anodized matte finishDescriptionBuriable Power House
MIL-E3-PPBT* E3 powering device * Electronically, striker or hair pin initiated * Uses E3 head attachments * Aluminum with MIL SPEC anodized matte finishDescriptionUniversal Push/Pull Booby Trap
MIL-E3-DC* Transfers initiating pressure from E3 Powering Device to detonate any MIL-SIM-FX product * Aluminum with MIL SPEC anodized matte finishDescriptionDetonator Cap
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –44
E3 Family Support Items
E3 Family Support ItemsE3 FamilyMIL-E3-ILH* For use with E3 powering device * Uses rubber burst disc and FX Powder (Cool Smoke) * Directs effect straight out along a target line * Aluminum with MIL SPEC anodized matte finishDescriptionInline Head Assembly
MIL-E3-RAH* For use with E3 powering device * Uses rubber burst disc and FX Powder (Cool Smoke) * Directs effect at a 90° angle * Aluminum with MIL SPEC anodized matte finishDescriptionRight Angle Head Assembly
MIL-E3-RAHM* Right Angle Head (with airline port) for use within the E3 familyDescriptionRight Angle Head with MILES Capability
MIL-E3-ETS* External Trigger Switch with banana plugs * Opens or closes an electrical current DescriptionExternal Trigger Switch
MIL-E3-HBS* Hacksaw Blade Switch Detonator * Opens or closes an electrical currentDescriptionHacksaw Blades
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –45
E3 Family Support Items
E3 Family Support ItemsE3 FamilyMIL-EIPB-MSW* Ball Bearing Switch * Tilt switch with wire harness and banana plugs
DescriptionTilt Switch
MIL-E3-CBL* 14 inch Connector CableDescriptionE3 Cable
MIL-SVX-CBL* 38 inch Connector Cable Description38 inch Connector Cable
MIL-E3-RXC* Magnetic Lid for the MIL-E3-RXPPDescriptionMagnetic Lid
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –46
E4 Support Items
E4 Support ItemsE4 Support ItemsMIL-E4-SOLKIT* One solenoid repair kit with 60 inch leads * Bare wire leads specific to the E4DescriptionE4 Solenoid Replacement Kit
MIL-E41-SOLKIT* One solenoid repair kit with 60 inch leads * Banana Plug leads specific to the E4-1DescriptionE4-1 Solenoid Replacement Kit with Banana Plug Leads
MIL-E4-AT* Compressed Air Chamber for the E4 * 60 inch bare wire leads DescriptionE4 Air Trigger with Bare Wire Leads
MIL-E4-AT1* Compressed Air Chamber for the E4-1 * With 60 inch banana plug leadsDescriptionE4 Air Trigger with Banana Plug Leads
MIL-E4-ATA* Compressed Air Chamber / Base Assembly for the E4 * 60 inch bare wire leadsDescriptionE4 Air Trigger and Base Assembly with Bare Wire Leads
MIL-E4-ATA1* Compressed Air Chamber / Base Assembly for the E4-1 * 60 inch banana plug leadsDescriptionE4 Air Trigger and Base Assembly with Banana Plug Leads
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –47
ECHO System Support Items
ECHO System Support ItemsECHO System Support ItemsMIL-06ST-SMU* 6" Volumizer with Male Union installs on existing ECHO System * Doubles the FX Powder (Cool Smoke) (Cool Smoke) capacity/powder signature effect * Holds 11 ounces of FX Powder (Cool Smoke) (Cool Smoke) * MIL SPEC hard anodized matte finishDescription6 inch Volumizer with Male Union
MIL-12-TP* 12" Bottle Protector safeguards device when burying or placing a single ECHO device on a roadway * MIL SPEC hard anodized matte finish DescriptionBottle Protector
MIL-ECH-BKIT* Kit converts an individual device from the ECHO into a buriable device * Includes: Airline, Dead Man Switch, Volumizer, Tank Protector and Right Angle Head * MIL SPEC hard anodized matte finish DescriptionBuriable Upgrade Kit
MIL-ECH-SP* ECHO Set Plug replacement part * Machined Aluminum * MIL SPEC hard anodized matte finish DescriptionSet Plug for Firing Initiator
MIL-ECH-TP* ECHO Thread Protector replacement part * Machined Aluminum * MIL SPEC hard anodized matte finishDescriptionThread Protector
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –48
ECHO System Support Items
ECHO System Support ItemsECHO System Support ItemsMIL-SS-FAS/W-2* Stainless Steel fasteners used to attach the MIL-ECH-CDH6 to the 5 cell caddy (NPSSD) * Stainless/Rubber Washers * Sold in Set of 2DescriptionReplacement Bolts and Washers
MIL-THN-D* Used to remove SS Fasteners from the 5 cell caddy * Also used to remove airline connectors * A steel ½" x 6" point socket T-Handle wrench * Powder-coated blue DescriptionT-handle Nut Driver
MIL-WOH6-ORK* O-Ring replacement kit for the ECHO System * Includes: 4 - 401 O-Rings 4 - 230 O-Rings 4 - Green Loctite capsules DescriptionO-Ring Replacement Kit for the ECHO
MIL-ECH-FIS* Dry Firing Set for New Equipment Training * Can be used for indoor classroom environment or outdoor systems useDescriptionFire Indicator Set
MIL-4SOL-KITReplacement solenoid kit for the Compressed Air Chamber * Long leads, no banana plugsDescription4 Solenoid Repair Kit with Bare Wire Leads
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –49
Fill Station Support Items
Fill Station Support ItemsFill Station and Fill Station Support ItemsMIL-FIL* Includes: 1 - Fill Station 1 - Adaptor Hose/Adapter w/ Pin Depress Assembly 1 - Vent Hose Assembly 1 - Vent Hose Muffler * Used for filling CO2 in the Refillable CO2 bottles * Machined aluminumDescriptionFill Station
MIL-SCALE* Used for weighing Refillable 9 oz CO2 tanks Molded plastic housing * Digital electronics internal DescriptionWeigh Scale
MIL-FIL-ADP* Fill station adapter assembly replacement piece with pin depress * Machined aluminum * Stainless steel internal parts * Plastic knob DescriptionFill Station Adapter
MIL-FIL-AHA* Fill Station adapter assembly replacement piece with hose/pin depress * Machined aluminum * Stainless steel internal parts * High pressure nylon hoseDescriptionFill Station Adapter Hose Assembly
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –50
Fill Station Support Items
Fill Station Support ItemsFill Station and Fill Station Support ItemsMIL-PD-ORK* Package of 10 O-Ring * Replacement O-Ring for the Fill Station Pin Depressor * Urethane O-Ring DescriptionFill Station Pin Depressor O-Ring
MIL-FIL-BCW* Package of 5 Bulk Tank Coupling Washers * Design allows washer to seat snuggly in the threads and prevents washers from falling out and becoming lostDescriptionBulk Coupling Washer
MIL-FIL-KIT2* Includes: - Replacement O-Rings - Valve Seats - Pipe Nipple Disassembly Tool - Silicone Grease Capsule * Stainless, nylon, Buna internal partsDescriptionFill Station Service Kit
MIL-SL* Silicone lube used to lubricate the O-Ring of the CO2 Filling Station * Silicone lube DescriptionSilicone Lube
MIL-FSW* Fill Station Wrench * Used to attach/remove valve to tank * Steel powder coated DescriptionFill Station Wrench
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –51
Fill Station Support Items
Fill Station Support ItemsFill Station and Fill Station Support ItemsMIL-12-AW* 12" Adjustable WrenchDescriptionAdjustable Wrench
MIL-516T-AW * 5/16" T-Handle Wrench used to service the CO2 Fill Station * Forged steel
Description5/16 T-Handle Allen Wrench
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –52
Firing Actuators and Firing Actuator Assemblies
Firing Actuators and Firing Actuator AssembliesFiring Actuators and Firing Actuator AssembliesMIL-12G-FA* A standard 12 gram firing actuator * Used in the small MIL-SIM-FX devices * Machined aluminum * MIL SPEC hard anodized matte finish Description12 Gram Firing Actuator
MIL-12G-FBA* 12 gram Tank Base/Firing Actuator Assembly Includes: 1 - 12 gram Tank Base 1 - 12 gram Tank Firing Actuator 1 - 5 Inch Slams Tube 1 - 12 gram Cartridge Housing * Machined aluminum * MIL SPEC hard anodized matte finishDescription12 Gram Tank Base Firing Actuator Assembly
MIL-12G-NCA* 12 gram Tank Base/Nose Cone Firing Actuator Assembly Includes: 1 - 12 gram Tank Base 1 - 12 gram Nose Cone Firing Actuator 1 - 5 Inch Slams Tube 1 - 12 gram Cartridge Housing * Machined aluminum * MIL SPEC hard anodized matte finish Description12 Gram Nose Cone Firing Actuator Assembly
MIL-9R-FA* Standard 6oz firing actuator * Machined aluminum * MIL SPEC hard anodized matte finishDescription9 Ounce Firing Actuator
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –53
Firing Actuators and Firing Actuator Assemblies
Firing Actuators and Firing Actuator AssembliesFiring Actuators and Firing Actuator AssembliesMIL-12G-NFA* 12 gram nose cone firing actuator * Used in the small MIL-SIM-FX devices * Machined aluminum * MIL SPEC hard anodized matte finishDescription12 Gram Nose Cone Firing Actuator
MIL-9R-FBA* 9 ounce Tank Base/Firing Actuator Assembly Includes: 1 - 9 ounce Tank Base 1 - 9 ounce Tank Firing Actuator 1 - Airline Connector * Machined aluminum * MIL SPEC hard anodized matte finishDescription9 Ounce Tank Base/ 9 Ounce Firing Actuator Assembly
MIL-9R-NFA* 9oz nose cone firing actuator * Machined aluminum * MIL SPEC hard anodized matte finishDescription9 Ounce Nose Cone Firing Actuator
MIL-9R-NCA* 9 Ounce Tank Base/Nose Cone Firing Actuator Assembly Includes: 1 - 9 Ounce Tank Base 1 - 9 Ounce Nose Cone Firing Actuator * Machined aluminum * MIL SPEC hard anodized matte finishDescription9 Ounce Tank Base/ 9 Ounce Nose Cone Firing Actuator Assembly
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –54
Ground Stakes and Ground Stake Support Items
Ground Stakes and Ground Stake Support ItemsGround Stakes and Ground Stake Support ItemsMIL-4.5-GS* 4.5" ground stake used with the ECHO System * Heat treated anodized steelDescription4.5 inch Ground Stake
MIL-06-GS* 6" ground stake used on the Directional Charge Head (MIL-180-CH) and the Ground Stake Block (MIL-90-GSB) * Heat treated anodized steel Description6 inch Ground Stake
MIL-08-GS* 8" ground stake used on the Ground Stake Block (MIL-90-GSB) * Heat treated anodized steel Description8 inch Ground Stake
MIL-90-GSB* Ground stake block used with ground stakes on a number of MIL-SIM-FX devices * Machined aluminum * MIL SPEC hard anodized matte finishDescription90 Degree Ground Stake Black
MIL-GSB-6A* Ground Stake Block / 6 Inch Ground Stake Assembly * Machined aluminum / Heat treated anodized steelDescriptionGround Stake Assembly with 6 inch Stakes
MIL-GSB-8A* Ground Stake Block / 8 Inch Ground Stake Assembly * Machined aluminum / Heat treated anodized steel DescriptionGround Stake Assembly with 8 inch Stakes
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –55
Ground Stakes and Ground Stake Support Items
Ground Stakes and Ground Stake Support ItemsGround Stakes and Ground Stake Support ItemsMIL-GSB-BLT* Replacement 3/8" bolt used in the ground stake block * Stainless steel DescriptionGround Stake Block Replacement Bolt
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –56
Hardwire Detonators Support Items
Hardwire Detonators Support ItemsHardwire via Airline Support ItemsMIL-12G-TCDA* Trigger Command Detonator Upgraded Airline Connector Kit * Includes brass fitting, airline connector and roll pin
DescriptionTrigger Command Detonator Upgrade
MIL-18-1032-ACK* Package of 1/8" x 10/32" airline connector for connecting the airline to the MIL-SIM-FX device * Push lock connection * Plated brass with nylon partDescriptionAirline Connectors 1/8 X 10/32
MIL-DMS-PLG* Replacement Part * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionDead Man's Switch Detonator Plug
MIL-PAD-PLG* Replacement Part * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionPressure Applied Detonator Plug
MIL-DMS-SQB* Replacement Part * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionLow Profile SQUIB for the Dead Man's Switch Detonator
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –57
Hardwire Detonators Support Items
Hardwire Detonators Support ItemsHardwire via Airline Support ItemsMIL-LIB* Lever Initiated Body - Replacement Part * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionLever Initiated Body
MIL-FVA-ORK* Small O-Ring fits inside the Fill Valve Adapter * Package of 10 O-RingsDescriptionFill Valve Adapter O-Ring Kit
MIL-LP* Used in the MIL-12G-PAD, MIL-12G-DMS, MIL-DMS-IED * Plastic lanyard with two stainless steel pins DescriptionPressure/Sensitive Device Lanyard and 2 Safety Pins
MIL-MFD-KIT* Striker, spring and screw used in the Multifunction Detonator * Stainless Steel DescriptionMulti-function Detonator Repair Kit
MIL-TCD-12C* Cup used for holding the disposable 12 gram cartridges * Connects to the Trigger Command Detonators head * Molded plastic DescriptionTrigger Command Detonator Cup
MIL-TCD-FVA* A Conversion adapter that allows for the Trigger Command Detonator to be used as a compressed air filling device * Stainless steel DescriptionTrigger Command Detonator Adapter
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –58
Hardwire Detonators Support Items
Hardwire Detonators Support ItemsHardwire via Airline Support ItemsMIL-TCD-ORK* O-Ring used in the head of the Trigger Command Detonator * Includes capsule of silicone grease * 10 - Urethane O-Rings Description12 gram Trigger Command Detonator O-Ring
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –59
Heads
HeadsHeadsMIL-110-FHA* Female Adapter used on the MIL-SIM-FX IED heads for a 110 degree ground marking effect * Machined aluminum * MiIL SPEC hard anodized matte finishDescriptionLP Female Adapter with 110 Degree Spray Pattern
MIL-110-MFA* Head assembly includes: 1 - Mortar Fin Attachment w/ 7 Fins 1 - Dispersed Impact Head 1 - LP Female Adapter w/ 110° Spray Pattern 1 - Stainless Steel Deflector * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionMortar Fin Head/ Female Adapter with 110 Spray Assembly
MIL-110-PEA* Head assembly includes: 1 - Pointed End Cap 1 - LP Female Adapter w/ 110° Spray Pattern 1 - Stainless Steel Deflector * Machined aluminum * MIL SPEC hard anodized matte finish DescriptionPointed End Cap/Female Adapter with 110 Spray Assembly
MIL-180-CH* Directional charge head used on the MIL-SIM-FX IED tubes (recommend to be used with ground stakes attached) * Has marking rounds capability for damage assessment * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionDirectional Charge/Improvised Claymore
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –60
Heads
HeadsHeadsMIL-180-CHA6* Head assembly includes: 1 - Directional Charge Head 1 - LP Male Adapter 2 - 6 Inch Ground Stakes * Has marking rounds capability for damage assessment * Machined aluminum * Mil spec hard anodized matte finish DescriptionDirectional Charge Head/Male Adapter with 6 inch Stakes
MIL-180-CHA8* Head assembly includes: 1 - Directional Charge Head 1 - LP Male Adapter 2 - 8 Inch Ground Stakes * Has marking rounds capability for damage assessment * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionDirectional Charge Head/Male Adapter with 8 inch Stakes
MIL-180-FHA* Female Adapter used on the MIL-SIM-FX IED heads for a 180 degree ground marking effect * Machined aluminum * MiIL SPEC hard anodized matte finishDescriptionLP Female Adapter with 180 Degree Spray Pattern
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –61
Heads
HeadsHeadsMIL-180-MFA* Head assembly includes: 1 - Mortar Fin Attachment w/ 7 Fins 1 - Dispersed Impact Head 1 - LP Female Adapter w/ 180° Spray Pattern 1 - Stainless Steel Deflector * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionMortar Fin Head/ Female Adapter with 180 Spray Assembly
MIL-180-PEA* Head assembly includes: 1 - Pointed End Cap 1 - LP Female Adapter w/ 180° Spray Pattern 1 - Stainless Steel Deflector * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionPointed End Cap/Female Adapter with 180 Spray Assembly
MIL-250-SMA* Male Adapter used on the MIL-SIM-FX IED heads * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionLP Male Adapter
MIL-3-CDH* This combination Head uses either rubber or plastic burst discs * Machined Aluminum with MIL SPEC hard anodized matte finish * Retainer ring (MIL-BD-RR) sold separately DescriptionCombination Disc Head
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –62
Heads
HeadsHeadsMIL-4-BFA* Bomb Fin Visual Modification * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionBomb Fin Attachment with 4 Fins
MIL-6-DPH* Commonly used with the Bomb Fin attachment (MIL-4-BFA) and the Mortar Fin Attachment (MIL-7-MFA) * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionDispersed Impact Head
MIL-6-MFA* A 6 fin mortar head visual modification used on the MIL-SIM-FX IED tubes * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionMortar Fin Assembly with 6 Fins
MIL-7-MFA* A 7 fin mortar visual modification used with the MIL-6-DPH * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionMortar Fin Assembly with 7 Fins
MIL-90-CH* Directional charge head used on the MIL-SIM-FX IED tubes * Eyelets can be attached for fastening head to an object * Has marking rounds capability for damage assessment * Machined aluminum * MIL SPEC hard anodized matte finish DescriptionARC Head
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –63
Heads
HeadsHeadsMIL-90-CHA* Head assembly includes: 1 - A.R.C. Head 1 - LP Male Adapter 2 - Eyelet Screws * Has marking rounds capability for damage assessment * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionARC Head/Male Adapter Assembly - With Eyelets
MIL-E4-CHA* Head assembly includes: 1 - A.R.C. Head 1 - LP Male Adapter * Has marking rounds capability for damage assessment * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionARC Head/Male Adapter Assembly - No Eyelets
MIL-EC-ST* End cap used when transporting powder filled MIL-SIM-FX IED 120mm (MIL-120-SM) and 20 inch (MIL-20-ST) tubes * Machined aluminum * MIL SPEC hard anodized matte finish DescriptionEnd Cap
MIL-EFP* Explosively Formed Penetrator Simulator Head * Specifically designed to be used with marking rounds * 42" marking zone at approximately 25 feet * MIL SPEC anodized matte finish DescriptionExplosively Formed Penetrator Array Head
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –64
Heads
HeadsHeadsMIL-PEC-ST* Pointed End cap used on the MIL-SIM-FX IED devices * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionPointed End Cap
MIL-PET-BA* Used on the larger MIL-SIM-FX tubes for exploding plastic beverage bottles * Allows for maximum audio signature * Machined aluminum * MIL SPEC hard anodized matte finish DescriptionConcussive PET Bottle Adapter
MIL-PET-DBA* Directional Charge Capabilities ( 60° Cone Spray) * Used on the larger MIL-SIM-FX tubes and ECHO System for exploding plastic beverage bottles * Allows for maximum audio signature * Machined aluminum * MIL SPEC hard anodized matte finishDescriptionDirectional Charge Concussive PET Bottle Adapter
MIL-SMA-TP* Thread protector replacement part * Machined aluminum * MIL SPEC hard anodized matte finish DescriptionThread Protector for LP Male Adapter
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –65
Landmine Support Items
Landmine Support ItemsLandmine Support ItemsMIL-14-40-OFF* Pressure Sensitive CO2 Pierce Pin for Pressure Sensitive Landmine * 40 lbs step off detonation * Machined aluminum * MIL SPEC hard anodized matte finish DescriptionPressure Release Pin for MIL-LM
MIL-14-40-ON* Pressure sensitive CO2 pierce pin for Pressure Sensitive Landmine * 40 lbs step on detonation * Machined Aluminum * MIL SPEC hard anodized matte finish DescriptionPressure Applied Pin for MIL-LM
MIL-16-SPK* Package of 2 * 7/8 X 2 Landmine Spring DescriptionLandmine Spring
MIL-M16LM6* Landmine base plug * MIL SPEC hard anodized aluminumDescriptionLandmine Base Plug
MIL-LM-PRT* Removes Landmine base plug * Stainless steel with lanyardDescriptionLandmine Base Plug Removal Tool
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –66
Miscellaneous Support Items
Miscellaneous Support ItemsMiscellaneous Service PartsMIL-BD-RR* Rubber burst disc retainer ring used with various devices * Machined aluminum * MIL SPEC hard anodized matte Olive Drab finishDescriptionBurst Disc Retainer Ring
MIL-PET-N* Replacement nut * Works in conjunction with the Concussive FX PET Bottle Adapter Head and the Directional Charge PET Bottle Adapter Head DescriptionPET Bottle Adapter- Replacement Nut
MIL-12G-SB1* 12 gram Cartridge Housing used in the 5 inch tube assembly * MIL SPEC hard anodized matte finish * Machined aluminumDescription12 gram CO2 Cartridge Housing
MIL-PP* Safety/Pull pin used in MIL-E3-PPBT * Sold in singlesDescriptionSafety/Pull Pin
MIL-SFTY-K* Package of 10 * Safety pin for many of the MIL-SIM-FX IED's * 4571 Stainless Steel DescriptionAnti-Personnel Safety Pin
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –67
Miscellaneous Support Items
Miscellaneous Support ItemsMiscellaneous Service PartsMIL-HTP* A tapered pin for use in specific Tripwire devices * 4571 stainless steel * Sold in singlesDescriptionHair Trigger Pin
MIL-6F-TW* Tripwire and Hair Trigger Pin * 4571 stainless steel DescriptionTripwire - 6 Foot Length
MIL-CHA-ENS* Package of ten Eyelets with nuts for the CHA headDescriptionEyelet and Nut Set
MIL-LNYRD* Lanyard * Polypropylene webDescriptionLanyard
MIL-SPN* Measuring spoon for measuring FX Powder (Cool Smoke) * Stainless Steel DescriptionMeasuring Spoon
MIL-6-001* Steel deflector used in the MIL-SIM-FX ordnance and mortar fin vismods * Stainless steel DescriptionStainless Steel Deflector
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –68
Miscellaneous Support Items
Miscellaneous Support ItemsMiscellaneous Service PartsMIL-12V-7AH* Rechargeable Battery * 7 AMP Hours * Bolt Posts DescriptionRechargeable Battery
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –69
O-Rings
O-RingsO-Ring MIL-TCD-ORK* Package of 10 * Trigger Command O-Ring ReplacementDescriptionTrigger Command Detonator O-Rings
MIL-PD-ORK* Package of 10 * Pin Depressor O-Ring ReplacementDescriptionPin Depressor O-Ring
MIL-41010-ORK* Package of 10 * Urethane O-Rings used on the High Pressure Bottle, ECHO Set Plug and ECHO Firing Indicator DescriptionCO2 Bottle O-RingMIL-013-ORK* Package of 10 * 013 O-RingDescriptionSolenoid Replacement O-Ring Buna
MIL-020-ORK* Package of 10 * 020 O-RingDescriptionUrethane O-Ring Kit
MIL-022-ORK* Package of 10 * 022 HNBR 70 Durometer O-RingsDescriptionO-Ring Kit for the 12 gram Cartridge Housing
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –70
O-Rings
O-RingsO-Ring MIL-116H-ORK* Package of 10 * 116 HNBR 70 Durometer O-RingsDescriptionHNBR O-Ring Kit for the Firing Actuator and Landmine Base Plug
MIL-126-ORK* Package of 10 * 126 HNBR 70 Durometer O-RingsDescriptionHNBR O-Ring Kit
MIL-130-ORK* Package of 10 * 130 HNBR 70 Durometer O-RingsDescriptionHNBR O-Ring Kit for the PET Bottle Adapter
MIL-228-ORK* Package of 10 * 228 HNBR 70 Durometer O-RingsDescriptionHNBR O-Ring Kit
MIL-230-ORK* Package of 10 * 230 Urethane 70 Durometer O-Rings * Used Specifically on the MIL-3-CDHDescriptionUrethane O-Ring Kit MIL-230H-ORK* Package of 10 * 230 HNBR 70 Durometer O-Rings DescriptionHNBR O-Ring Kit
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –71
O-Rings
O-RingsO-Ring MIL-401-ORK* Package of 10 * 401 HNBR 70 Durometer O-RingsDescriptionHNBR O-Ring Kit
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –72
Radio Controlled Support Items
Radio Controlled Support ItemsAntennaMIL-ANT-1A* Antenna used on the Long Range Electronic Firing Device as well as the Long Range Transmitters * Rubber antenna with steel fitting * Includes Antenna Adapter (MIL-ANT-ADP)Description8 inch Rubber Whip Receiver Antenna
MIL-ANT-1B* Antenna used on the Long Range Electronic Firing Device as well as the Long Range Transmitters * Rubber antenna with steel fitting * Antenna Adapter (MIL-ANT-ADP) NOT IncludedDescription8 inch Rubber Whip Antenna - No Adapter
MIL-ANT-ADP*Antenna adapter used on the Long Range Electronic Firing Device/Long Range TransmittersDescriptionAntenna Adapter
TransmittersMIL-TX-1CH* Single button short range remote with lanyard * Used with any short range radio controlled device * Formed plastic * 315 MHz - 500 Feet LOSDescriptionOne Channel/Button Transmitter (315 MHz)
MIL-TX-2CH* A two button short range remote with lanyard * Used with any short range radio controlled device * 315 MHz - 500 Feet LOS * Formed plasticDescriptionTwo Channel/Button Transmitter (315 MHz)
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –73
Radio Controlled Support Items
Radio Controlled Support ItemsTransmittersMIL-TXL-1CH* A single button long range radio transmitter * Used with any long range radio controlled device * 27 MHz - 1 Mile LOS * Cast plastic DescriptionOne Channel/Button Transmitter (27 MHz)
MIL-TXL-4CH* A four button long range radio transmitter * Used with any long range radio controlled device * 27 MHz - 1 Mile LOS * Cast plasticDescriptionTwo Channel/Button Transmitter (27 MHz)
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –74
Suicide Vest Support Items
Suicide Vest Support ItemsSuicide Vests Support ItemsMIL-SVX* Modular Velcro pouches distribute weight evenly and allow for a variety of configurations on both front and back of vest * One size fits all * Pouches are sold separately * Power pack pouch (for remote detonation) is also available DescriptionSuicide X-Vest
MIL-SVX-PBP* One Single Pipe Bomb Pouch used with the Suicide X-Vest * H.D. Canvas DescriptionSVX Power Pack Pouch
MIL-SVX-RBP* One Single Power Pack Pouch used with the Suicide X-Vest * H.D. Canvas DescriptionSVX Pipe Bomb Pouch
MIL-SVX-CBL* 38 inch Connector Cable Description38 inch Connector Cable
MIL-SVX-RC* MIL-SVX4R Ripcord Replacement * 14 inches lengthDescriptionSV4R Ripcord Replacement
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –75
Tubes
TubesTubesMIL-05-ST* Small IED Tube * Holds up to 4 oz of FX Powder (Cool Smoke) * Base (MIL-12G-SB) not included * Machined aluminum * MIL SPEC hard anodized matte finishDescription5 Inch Tube
MIL-06ST-A* ECHO Tube * Holds up to 11 oz of FX Powder (Cool Smoke) * Machined aluminum * MIL SPEC hard anodized matte finishDescription6 inch Tube
MIL-20-ST* Medium IED Tube * Holds up to 22 oz of FX Powder (Cool Smoke) * Machined aluminum * MIL SPEC hard anodized matte finishDescription20 inch Tube
MIL-120-SIM* Large IED Tube * Holds up to 44 oz of FX Powder (Cool Smoke) * Machined aluminum * MIL SPEC hard anodized matte finishDescription120mm SIM Tube
PH: 519-688-0287 FX: 519-688-2063 EM: [email protected] Page –76