Comfort GSM Module

Click here to load reader

  • date post

    01-Sep-2014
  • Category

    Technology

  • view

    1.009
  • download

    2

Embed Size (px)

description

 

Transcript of Comfort GSM Module

  • Comfort GSM Module Chapter 1 UCM/GSM ............................ 2 Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 SIM Card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Contents of UCM/GSM Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Chapter 2 Setup ................................... 6 Location . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 UCM Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Indicator LEDs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 UCM Communication Status LEDs . . . . . . . . . . . . . . . . . . . . . 10 LEDS with SW8-H Shunted (Signal Strength) . . . . . . . . . . . 10 LEDS with SW8-H open (Normal) . . . . . . . . . . . . . . . . . . . . . 10 Modem Status LED . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Integrated Circuits on UCM . . . . . . . . . . . . . . . . . . . . . . . . . . 11 What to Watch Out For . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Chapter 3 Programming and Operation . . . . . 12 Comfigurator > Number of UCMs . . . . . . . . . . . . . . . . . . . . . 12 Programming for SMS Dial-out . . . . . . . . . . . . . . . . . . . . . . . 12 SMS Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Dialing out via GSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 Dialing In via GSM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Sending SMS Commands to Comfort . . . . . . . . . . . . . . . . . . 17 Version History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 1
  • Comfort GSM Module CHAPTER 1 UCM/GSM Features The UCM/GSM provides a cellular phone connection to Comfort. This gives Comfort the following abilities; 1. Acts as a backup for alarm dial-out when the land line is faulty or cut. Alternately, it can be used without a fixed telephone line, for installations where a telephone line is not available or not desired. 2. Allows the user to dial to the GSM number instead of the fixed telephone line to access Comfort menus. There is no voicemail on this line. 3. Allows Comfort to report alarms to the users cellular phones via SMS (Short Message Service). For Comfort Pro, the SMS message will show numeric information corresponding to the alarm type and zone number, user number or module ID. For Comfort Ultra, the SMS message will show the alarm type and Zone description as text. 4. Allows users to send commands to control home appliances and the security system via SMS. In order for the UCM/GSM to be used, there must be a GSM (Global System for Mobile Communications) service in the area. GSM is currently widely available is Europe and Asia. Refer to http://www.gsmworld.com/roaming/index.shtml for network operators worldwide that offer services from the GSM family of Wireless Communications. Specific details included within this section are network, roaming, services and coverage information for over 500 operators in 207 countries/areas of the world. The UCM/GSM operates on dual-band frequency i.e. 900 MHz and 1800 MHz. It currently does not support 1900 MHz which is used in the US. The UCM/GSM requires a Subscriber Identity Module (SIM) card to be inserted, just like with a cellular phone. This can be a prepaid card, or one which is billed monthly according to a usage plan. Requirements 1. Comfort Controller PCB Rev E6 with U1 Firmware O4.222 Comfort PRO model) or Action 4.221 (Comfort Ultra model). Comfort PCB revisions prior to E6 are NOT able to support the UCM/GSM. 2. Comfigurator version 1.4.0 and above. 2
  • Comfort GSM Module SIM Card A SIM (Subscriber Information Card) must be used in the GSM Module. This may be a prepaid card or one which is billed monthly as part of a service plan. However, it is not advisable to use a prepaid card as the user would not know when the amount remaining has been used up. If SMS is to be sent, then the card must allow sending of SMS. If incoming SMS commands are to be accepted, then Caller ID must be enabled. This may incur an additional charge. The SIM card will come with a telephone number. Use this number to dial to the system via the GSM module. Contents of UCM/GSM Kit UCM/GSM module consisting of; 1. UCM with firmware GSM5.XX. This is NOT a regular UCM which can be used to program Comfort or learn infrared codes. 3
  • Comfort GSM Module 2. Antenna with 2 meter cable and FME connector 3. Serial cable with Male-male 8 way D connectors 4. Audio cable: telephone cable with 4 way telephone plug (RJ9) at one end and 5 way connector at the other end. 4
  • Comfort GSM Module 5. Power Supply Cable with 6 way (RJ11) plug at one end and a 2 way terminal block at the other end 6. GSM modem. 5
  • Comfort GSM Module CHAPTER 2 SETUP Location Ensure that the location where the module is mounted has sufficiently good reception for the GSM Network. The signal strength can be tested using the SW8-H jumper as described in the Jumper Settings section below. The UCM/GSM can be located several hundred meters away from the Comfort controller so that it should be possible to find a location where the reception is good. Connections 1. Connect the antenna to the GSM Module by screwing it to the FME connector. Place the antenna outside any metal casing which may be used to house the UCM/GSM module. The base of the antenna is magnetic and can sit on a metal surface like the Comfort enclosure. 6
  • Comfort GSM Module 2. Connect the 6-way RJ11 telephone jack of the power cable to the GSM Module. 3 signals need to be connected to the Comfort controller board; Pin Signal Colour Comfort 1 VCC Blue 12V 4 TO_IN Red 12V 6 GND White 0v/COM The other signals are left unconnected. The supply voltage and ground signals are reverse polarity and overvoltage-protected on the GSM Module. The Comfort end of the cable is terminated in a two way terminal block for convenience. If necessary, remove the wires from the terminal block and connect them to the appropriate terminals 12V and 0V on Comfort. 3. Connect the 4 way telephone jack of the audio cable to the GSM module. The other end is connected to the white J23 header on Comfort. This header exists only the Comfort PCB Rev E6 and not on previous PCB versions. 7
  • Comfort GSM Module 4. Connect the serial DB9 to DB9 cables between the GSM Module and the UCM serial connectors. 5. Remove the SIM card cover and insert the SIM card as Shown. 8
  • Comfort GSM Module UCM Jumper Settings SW7 - UCM ID The SW7 ID shunts on the UCM/GSM should be set to ID in the range 2 to 8 as in the table below. ID - SW7 SW7- A SW7 - B SW7 - C 1 Short Short Short 2 Open Short Short 3 Short Open Short 4 Open Open Short 5 Short Short Open 6 Open Short Open 7 Short Open Open 8 Open Open Open ID=1 is reserved for the UCM used for programming with Comfigurator. Do not set the UCM/GSM id to 1. Set the ID to one which is not used by any UCM installed in the system. For example if ID=2 for C-Bus and UCM=3 for Smartfit has been installed, then ID=4 should be used. This ID should correspond with the Number of UCMs setting in Comfigurator > Modules and Settings screen. SW8 Positions A to G are unused. Position H is open for normal operation and shunted to give signal strength indication on the LEDS RDY, BUSY1, BUSY2, ERR. 9