columns

ARCHITECTURAL PRODUCTS BY OUTWATER L.L.C. • Phone: 1-800-835-4400 Fax: 1-800-835-440367

Strength AndDurability...Structural FiberglassColumns are spun from amixture of 45% genuinemarble particles combinedwith tough polymer resinsand fiberglass. They havethe look and feel of marble.They are hard, lightweight,and strong. They will neversplit or rot and are abso-

lutely termite-proof.

EasyInstallation...Simple instructions included with each unit assure quick and easy installation. All StructuralFiberglass Columns come complete with a Tuscan cap and base in polyurethane. The finishreadily accepts high quality exterior paint. Minimal surface preparation may be required. Oncepainted, our columns will not deteriorate under severe long-term weathering and are extremelyresistant to fire and impact.

Advantages... • Architecturally

Correct Tuscan Styleenhances anystructure in anysetting.

• No splitting orrotting.

• Will not deterioratein heavy weathering.

• Resistant to impactdamage.

• Termite-proof.

• Fire resistant.

• Fast & easy to install.

• Maintenance-free.

• Designed to bearstructural loads.

STRUCTURAL FIBERGLASS COLUMNS

VISIT US ON LINE AT www.outwater.com • We Accept Major Credit Cards68

RESIN CAPITALS FOR USE WITH OUR ROUND FIBERGLASS COLUMNS• HIGH LOAD BEARING CAPACITY • WATERPROOF • EASY TO INSTALL • INSECTPROOF

LOAD BEARING CAPACITY

HOW TO FINISH

It's Simple: No primer coat is necessary. Be sure to use a high quality paint and follow the manufacturer's instructions for best results.

Our capitals provide both a decorative as well as structural function. The results of independentlyoperated compressive strength testing and load bearing capacities of our capitals are listed in the chart:

WE CANNOT ASSURE APROPER FIT ON USE WITHOTHER MANUFACTURER'S

COLUMNS

DIAMETER LOAD IN POUNDS6 Inches8 Inches10 Inches12 Inches

8,00010,00012,50015,000

NAME PART # FITS OUR COLUMN DIA. BOTTOM DIA. (A) HEIGHT (B) ABACUS (C) WEIGHT IN LBS. EACH

1 RomanIonic

MC-6-I 6" 4-7/8" 2-1/4" 5-3/4" 4 90.00MC-8-I 8" 6-5/8" 3" 7-7/8" 5-1/2 120.00

MC-10-I 10" 8-3/8" 4" 10" 12 150.00MC-12-I 12" 10" 5-1/8" 12-1/4" 20 185.00

2 Scamozzi

MC-6-S 6" 5-1/8" 2-1/2" 7-5/8" 5 91.25MC-8-S 8" 6-1/4" 3" 9-3/4" 7-1/2 130.00

MC-10-S 10" 8-1/4" 3-5/8" 13-3/8" 15 150.00MC-12-S 12" 9-7/8" 4-3/4" 16-1/4" 24 185.00

3 RomanCorinthian

MC-8-C 6" 4-3/8" 7" 9-3/8" 8 97.00MC-8-C 8" 6-1/2" 9-3/8" 11-3/8" 14 150.00MC-10-C 10" 8-1/8" 11-3/16" 14-1/4" 26 210.00MC-12-C 12" 9-1/2" 13-3/4" 19-1/2" 55 250.00

4 Temple ofWinds

MC-6-TW 6" 5-1/8" 6-7/8" 7-7/8" 7 91.25MC-8-TW 8" 6-1/2" 7-3/8" 10-3/8" 8 145.00

MC-10-TW 10" 8-1/8" 10" 13-3/4" 24 190.00MC-12-TW 12" 10-1/8" 10-1/2" 15-3/4" 42 240.00

5 GreekErectheum

MC-6-GE 6" 5" 3-1/4" 6-5/8" 5 85.50MC-8-GE 8" 6-1/4" 3-5/8" 7-5/8" 6 130.00MC-10-GE 10" 8" 5" 10-3/8" 20 150.00MC-12-GE 12 9-1/2" 5-5/8" 12" 26 198.00

PLEASE NOTE: All dimensionsare considered accurate at timeof printing. However, there maybe some slight differences inthe future - If dimensions arecritical, verify when placingyour order.

1

2

34

5

Temple of Winds Roman Corinthian Greek Erecthium Roman Ionic Scamozzi

The "B" dimension is the height added to your column height.

When using a decorative capital, column should be cut just above bead on neckingfor cap to look & fit correctly.

BOTTOMDIAMETER

CUT AT BEADDIAMETER

CUT AT BEADHEIGHT LOSS

INSIDE TOPDIAMETER

8"10"12"

DP 7-9/16"DP9-1/4"DP10-3/4"

4"5"

5-3/4"

5-1/2"7-1/8"8-3/4"


PLEASE NOTE: PRICES ABOVE INCLUDE A STANDARD POLYURETHANE CAP AND BASE.

Genuine marble particles are combined with polymers and fiberglass in special molds and spun into a marble-hard columnhaving an architecturally true taper. Virtually maintenance-free columns must be painted to assure a lifetime of beauty andservice

LARGER SIZES AVAILABLE IN PLAIN STYLE ONLY PLEASE INQUIRE

* ATTIC BASE AVAILABLE AT AN ADDITIONAL FEE:

STRUCTURAL FIBERGLASS COLUMNS

STRUCTURAL LOAD LIMITS

PLAIN FLUTED

PART # SIZE STYLE WEIGHT PRICE EA.MC-68

MC-68F6" x 8'6" x 8'

PLAINFLUTED

40 lbs.40 lbs.

147.00183.00

MC-856MC-88

MC-88FMC-89

MC-89FMC-810

MC-810F

8" x 5'6"8"x8'8"x8'8"x9'8"x9'

8"x10'8"x10'

PLAINPLAIN

FLUTEDPLAIN

FLUTEDPLAIN

FLUTED

29 lbs.44 lbs.52 lbs.49 lbs.63 lbs.50 lbs.66 lbs.

154.00164.85201.60172.20224.70190.05242.55

MC-108MC-108FMC-109

MC-109FMC-1010

MC-1010FMC-1012

MC-1012F

10"x8'10"x8'10"x9'10"x9'

10"x10'10"x10'10"x12'10"x12'

PLAINFLUTEDPLAIN

FLUTEDPLAIN

FLUTEDPLAIN

FLUTED

54 lbs.76 lbs.59 lbs.84 lbs.64 lbs.82 lbs.76 lbs.84 lbs.

208.95270.90222.60286.65240.45300.30321.30373.80

MC-128MC-128FMC-129

MC-129FMC-1210

MC-1210FMC-1212MC1212F

12"x8'12"x8'12"x9'12"x9'

12"x10'12"x10'12"x12'12"x12'

PLAINFLUTEDPLAIN

FLUTEDPLAIN

FLUTEDPLAIN

FLUTED

66 lbs.76 lbs.62 lbs.88 lbs.84 lbs.94 lbs.94 lbs.109 lbs.

269.85326.55292.95350.70317.10373.80435.75481.95

PART # COLUMN DIA.PLINTH

C DBASE MOLD

EPRICE

MC-ATTIC-6 6 8-1/2" 1-1/2" 2-7/16" 32.00 ea.MC-ATTIC-8 8 10-3/8" 1-1/4" 3-1/4" 38.07 ea.MC-ATTIC-10 10 13" 1-5/8" 4" 61.26 ea.MC-ATTIC-12 12 15-1/4" 1-7/8" 4-7/8" 75.08 ea.

COLUMNDIA.

MAXIMUMLOAD

6" 8"10"12"

10,000 lbs.10,000 lbs.14,000 lbs.18,000 lbs.

(NOTE: Decorative Caps & Bases areavailable.)

• Ideal for exterior use.• Sharp taper for a classical look.

COLUMN SIZE 6" 8" 10" 12"BOTTOM DIA. (A) 5-5/8" 7-5/8" 9-5/8" 11-5/8"

NECK DIA. (B) 5-1/2" 7" 8-3/4" 10-1/4"PLINTH (C), (D) 8-1/2", 1-1/2" 10-3/8",1-7/8" 13", 2-3/8" 15-1/4", 2-3/4"BASE MOLD (E) 1-3/4" 2-3/8" 2-7/8" 3-1/4"

CAP SQUARE (F) 7-9/16" 9-5/8" 12" 14-1/2"CAP ROUND (G), (H) 1-9/16", 1-3/16" 1-3/8", 1" 1-3/4", 1-1/4" 2", 1-3/8"

BEAD (K) 1" 1" 1" 1"FLUTE WIDTH (L) 5/16" 11/16" 7/8" 1"TOP FLUTE (M) 1" 1/2" 3/4" 1"

BOTTOM FLUTE (N) 6-1/4" 6-1/4" 7-1/4" 8"

PLEASE NOTE: Column heights listed are overall - STANDARD caps andbases do not add to the column height.


DURALITE SQUARE FIBERGLASS COLUMNSThe Duralite Column is easy to install because of its lightweight shaft and high density polyurethane cap, astragal/bead and baseset while having the load bearing capacity of 10,000 lbs. Duralite columns are extremely durable and virtually maintenance free.Choose from 8” , 10” or 12” square plain shafts. Heights are 8’, 9’ and 10’ (12” also available in 12’).

COLUMNSIZE

BOTTOMDIA.

NECKDIA.

PLINTHBASEMOLD

CAP SQUARE ECHINUS BEAD

A B C D E F G H K8" 7-1/2" 7-1/2" 10-3/8" 1-7/8" 2-3/8" 10-1/8" 1-3/8" 1" 1"10" 9-1/2" 9-1/2" 13" 2-3/8" 2-7/8" 12-3/4" 1-3/4" 1-1/4" 1"12" 11-1/2" 11-1/2" 15-1/4" 2-3/4" 3-1/4" 15-7/8" 2" 1-3/8" 1"

PART # SIZESHAFT

WEIGHT

PRICE(INCLUDES CAP & BASE &

ASTRAGAL/BEAD)

MC-88SQ 8" X 8' 32 lbs. 264.00

MC89SQ 8" X 9' 37 lbs. 297.00

MC810SQ 8" X 10' 40 lbs. 330.00

MC108SQ 10" X 8' 41 lbs. 352.00

MC109SQ 10" X 9' 46 lbs. 396.00

MC-1010SQ 10" X 10' 51 lbs. 439.00

MC-128SQ 12" X 8' 49 lbs. 439.00

MC-129SQ 12" X 9' 55 lbs. 502.00

MC-1210SQ 12" X 10' 61 lbs. 563.00

MC1212SQ 12" X 12' 73 lbs. 659.00

Remove all dust and dirt from surface of column as well as the cap and base with either mineral spirits or denatured alcohol priorto painting. Use a good, high quality alkyd or latex exterior paint on columns, caps, astragals (neck moulds) and bases. At least 1coat of primer and 2 coats of final paint should be applied. Be sure to follow paint manufacturer’s instructions concerning usewithin temperature ranges for best results. DO NOT use paint or solvents containing acetone.

FINISHING/PAINTING

• Be certain that the load is evenly distributed over the bearing surface of the cap and base.• If building code requires uplift protection, contact your distributor for recommendations.• To preserve and protect your column outdoors, it is necessary to coat with a high quality exterior primer, followed by exterior

paint.

INSTALLATION NOTES

NOTE: SQUARE COLUMNS ARE NOT AVAILABLE FLUTED.


4" & 6" Columns

CAP/BASE DIMENSIONS

PRICE INCLUDES CAP & BASE 8" Columns

COLONIAL SQUARE WOOD COLUMNS

Our graceful plain or fluted square columns are manufactured us-ing kiln-dried, finger-jointed Ponderosa pine. They include a poly-urethane cap and base, and are shipped unassembled. All of ourcolumns are treated with a wood preservative and are completelysanded.

PRICE INCLUDES CAP & BASE

*FOR PLAIN COLUMNS, ADD A "P" AFTER THE PART NO.; FOR FLUTED COLUMNS, ADD AN "F"AFTER THE PART NO. (PLAIN AND FLUTED SQUARE COLUMNS ARE THE SAME PRICE)

**SQUARE WOOD COLUMNS ARE NOT STRUCTURAL**PLEASE NOTE: COLUMNS COME UNASSEMBLEDPLAIN FLUTED

LOAD BEARING STRUCTURAL MEMBERS. . .Classic columns are self supporting. . .designed as decorative, load bearing elements forporches, entrances, driveway over hangs, etc. Ruggedly constructed, their load bearing capabilities are certified by an independent test-ing laboratory.PRIMED COLUMNS. . . Are coated with a mist of vinyl wash primer containing zinc chromate, ready to be finished with any good exteriorpaint except lacquer.PAINTED COLUMNS. . . Are electrostatically coatedwith a baked on high-solids polyester paint, to give amaintenance-free, uniform finish.PLEASE NOTE. . . In addition to the diameter and heightsshown, we are also able to fabricate custom columnsaccording to your specifications. Please inquire

EASY TO ASSEMBLE. . . .Square column staves snaptogether. This should be done on a solid surface such asthe floor or a table. The easiest method is to tilt all of thejoints in to place and snap the last on together. It is bestto use a rubber mallet for this. If using a steel hammer,be sure to use a block of wood on the columns to preventmarking the metal.

CLASSIC SQUARE ALUMINUM COLUMNSSTRUCTURAL INTEGRITY. . .LIFETIME DURABILITY

AVAILABLE PRIMED OR PAINTED-WHITE

CLEAR PINE/PAINT GRADE

COLUMNSIZE

A B C D

4"6"8"

4-1/2"5-1/2"7-1/2"

6-1/2"8-1/2"10-1/2"

1-7/8"2-3/4"2-3/4"

1"1-1/2"1-1/2"

PART#

COLUMNSIZE

NO. OFSTAVES

WT. INLBS.

A B CLOAD IN

LBS.PRIMEDEACH

PAINTEDEACH

CS48SCS68SCS88S

4" x 8'6" x 8'8" x 8'

324

15-1/22028

4-1/4"5-1/2"7-1/2"

4-1/4"5-1/2"7-1/2"

3-3/8"4-5/8"6-5/8"

11,00012,0009,000

90.00122.60174.00

92.70125.90178.10

PART #NOMINAL

SIZE ACTUAL SIZE WEIGHT PLAIN*/FLUTED*

DS68DS610DS88DS810

6" x 8'6" x 10'8" x 8'8" x 10'

5-1/4" x 5-1/4" x 8'5-1/4" x 5-1/4" x 10'7-1/4" x 7-1/4" x 8'7-1/4" x 7-1/4" x 10'

8 lbs.11 lbs.12 lbs.15 lbs.

85.70112.41130.22161.39


CLASSIC ROUND ALUMINUM COLUMNSSTRUCTURAL INTEGRITY. . .LIFETIME DURABILITY

AVAILABLE PRIMED OR PAINTED-WHITE, ALMOND OR SANDSTONE

LOAD BEARING STRUCTURAL MEMBERS. . .Classic columns are self supporting. . .designed as decorative, load bearing elementsfor porches, entrances, driveway over hangs, etc. Ruggedly constructed, their load bearing capabilities are certified by an indepen-dent testing laboratory.PRIMED COLUMNS. . . Are coated with a mist of vinyl wash primer containing zinc chromate, ready to be finished with any goodexterior paint except lacquer.PAINTED COLUMNS. . . Are electrostatically coated with a baked on high-solids polyester paint, to give a maintenance-free,uniform finish.

PLEASE NOTE. . . In addition to the diameter and heights shown, larger sizes are also available - Please inquire

DIMENSION DATA Compression LoadTest Results

EASY TO ASSEMBLE. . . (1)Before assembly, measure opening-cut column staves 1/8" longer with hacksaw. (2)To assemble, hook staves together-small hook joins large hook. (3)Hook all staves together except one-slide remaining stave into place. (4)Put cap & base on column set in place &plumb with level. Let weight down on column. (5)Slide cap & base into place & tighten screws.

All painted columnsare available inWhite. Asterisks indi-cate availability in Al-mond and Sand-stone. Please useproper code afterPartNo.(White=WH,A l m o n d = A L ,Sanstone = SS).

Primed & Painted Columns

CAPS & BASES SOLD SEPARATELY

1 2 3 4 5

COLUMNDIA.

NO. OFSTAVESWHOLE

COLUMN

NO. OFSTAVES

HALFCOLUMNS

COLUMNO.D.

COLUMNI.D.

6"8"10"12"

3345

2223

5-3/4"7-5/8"9-9/16"11-7/16"

4-15/16"6-13/16"

8-3/4"10-5/8"

COLUMNDIA.

NO. OFSTAVES

LOAD INLBS.

6"8"10"12"

3345

22,00020,00026,00026,000

PART # SIZEWEIGHTIN LBS.

PRIMEDPRICE EA.

PAINTEDPRICE EA.

*CR68CR69

*CR610

6"x8'6"x9'6"x10'

17-1/218-1/220-1/2

84.0094.50105.00

86.5097.30108.10

*CR88CR89

*CR810CR812

8"x8'8"x9'8"x10'8"x12'

21-1/423-1/225-3/430-1/4

108.60122.10135.70162.80

111.90125.90139.90167.90

*CR108 CR109 CR1010*CR1012

10"x8'10"x9'10"x10'10"x12'

28-1/231-1/234-1/4

40

133.10149.80166.40199.70

137.40154.50171.70206.10

CR128 CR129CR1210CR1212

12"x8'12"x9'12"x10'12'x12'

3740-3/444-1/451-1/2

195.66220.14244.62293.49

207.99234.00260.01312.03


CLASSIC ALUMINUM CAPITALS & BASESAVAILABLE PRIMED OR PAINTED - WHITE, ALMOND OR SANDSTONE

When using Corinthian Capitals, be sure to add theheight of the capital (Dim. C) in determining theoverall column height.

Corinthian Capitals

Modified Corinthian Capitals

All painted capitals are available in White. Asterisks indicates availability in Almond and Sandstone. Please use proper codes after part no. (White=WH, Almond=AL, Sandstone = SS).

Corinthian Cap

Modified Corinthian CapFor 10" Column

Modified Corinthian CapFor 12" Column

When using Scamozzi Capitalsbe sure to add the height of thecapital (Dim. C) in determin-ing the overall column height.

Scamozzi Cap

Scamozzi Cap

Decorative Base

Standard Base

Decorative Base

Standard Base

PART #COLUMN

DIA.A B C D E F

PRIMEDPRICE EA.

PAINTEDPRICE EA.

*CR8COR*CR10COR CR12COR

8"10"12"

7-3/4" 9-1/2"11-1/2"

6-13/16" 8-3/4"10-3/4"

12"14"

16-7/8"

12-3/8"14-1/2"16-7/8"

9-1/4"11-1/2"13-1/2"

11-3/4"15"

18-1/2"

248.10368.40588.60

250.20371.00591.48

PART #COLUMN

DIA.A B C D E F

PRIMEDPRICE EA.

PAINTEDPRICE EA.

*CR10MCOR CR12MCOR

10"12"

9-3/8"11-5/8"

8-3/4"10-5/8"

7-3/4"10-1/2"

8-1/8"10-7/8"

12-3/4"14-1/4"

14"16-1/4"

252.30352.08

254.40354.87

PART #COLUMN

DIA.A B C D E F

PRIMEDPRICE EA.

PAINTEDPRICE EA.

*CR8SCA*CR10SCA CR12SCA

8"10"12"

7-5/8" 9-1/2"11-1/2"

6-7/8"8-13/16"10-5/8"

3"3-1/2"

4"

3-1/2"4"

4-3/4"

8-3/4"11-1/4"13-1/2"

11-1/4"14-1/4"18-1/2"

117.70159.60332.01

118.70161.10333.90

PART #COLUMN

DIA.A B C D E

PRIMEDPRICE EA.

PAINTEDPRICE EA.

*CR6DB*CR8DB*CR10DB CR12DB

6" 8"10"12"

5-3/4" 7-5/8" 9-9/16"11-7/16"

6-1/8"8"

10-1/4"12-1/4"

8"10-1/2"13-1/2"

16"

3"4"5"6"

1-5/8"1-3/4"2-3/8"

3"

24.0036.6057.7087.12

24.4037.1058.3087.75

PART #COLUMN

DIA.A B C D E

PRIMEDPRICE EA.

PAINTEDPRICE EA.

*CR6SB*CR8SB*CR10SB CR12SB

6" 8"10"12"

5-3/4" 7-5/8" 9-9/16"11-7/16"

6-1/8"8"

10-1/4"12-1/4"

7-1/2"10"

12-1/2"15"

2-1/8"2-11/16"

3-3/8"4"

1-1/16"1-1/4"1-5/8"

2"

8.2010.8017.9025.29

8.6011.3018.6026.01


Prior To Storage OR Installation:Columns must be primed twice with an oil based exterior primer and painted once with an oil based exteriorpaint. The applies to shaft top, bottom, exterior and as much of interior as can be reached. Caps and bases arepolyurethane and do not require this preparatory step.

***** USE OIL BASED PRIMER & PAINTS ONLY...DO NOT USE LATEX! *****

VentilationVents are cut into all bases. These allow for air to enter column interior. Do not block these vents into possibledirect water contact. Do not block these vents. It is imperative that air is allowed to escape through the capital.This can be done in several ways. Some of the morecommon methods are:

A. Recessed Soffit Application - (with at least a 1/2" minimum recess). Does not require any further ventilation.B. Flush Soffit Application - requires blocking (1/2" minimum height) on both sides of cap vent hole, running the width of the cap.C. Flush Ceiling - requires drilling a hole in ceiling (the same size as and directly above cap vent hole).Make sure the cavity that the column is exhausting into is also ventedso that air may flow freely and any condensation can dissipate.

FinishingFill as needed with an exterior wood putty and sand. Lightly sand between coats.Use oil based primer and paints only...do not use latex! Prior to installation (orstorage) prime twice (with an oil based exterior primer) shaft top, bottom,exterior and as much of the interior that can be reached. Coat same surfaceswith one coat of an oil based exterior paint. If column is cut down, prime andpaint cut surface(s) prior to installation. After installation, column shaft, capand base can be finished with 1-2 coats of an oil based exterior paint.PROPER VENTILATION AND FINISHING ARE NOT SUGGESTIONS -THEY ARE REQUIRED FOR SUCCESSFUL INSTALLATION AND LONGCOLUMN LIFE.

Basic Column AssemblyThe two most common methods of column assembly are:

1. Assembling column outside installation locationDrive several galvanized or brass screws through top of cap into topof shaft, also through bottom of base into bottom of shaft. Slidecolumn into place and toenail/screw (using galvanized or brass fasteners)cap and base into mounting overhead surface and floor. Plug any holeswith an exterior wood putty, sand and finish.2. Assembling column within installation locationDrive several galvanized or brass screws through base into floor.Do same to attach cap to overhead mounting surface. Slide shaft inplace and toenail/screw (using galvanized or brass fasteners) intocap and base. Plug any holes with an exterior wood putty, sand and finish.

The assembly techniques shown are only the basics of installation. Location must be sound, plumb & level. Column shaftmay require to be trimmed prior to assembly. A bead of caulk/adhesive should be used on shaft ends (where shaft mountsto cap & base) and along outside where cap, shaft & base meet. This insures a good seal between components.

IMPORTANT NOTES REGARDING PROPERVENTILATION & FINISHING OF WOOD COLUMNS

A. Recessed Soffit

B. Flush Soffit

C. Flush Ceiling


Our columns are available in a kiln dried, clear, finger jointed pine or redwood. The staves are assembled usingtongue & groove joints and glued with a Type I waterproof glue, pine is dip treated with a wood preservativeand sanded. These are paint grade columns; stain grades are available as architecturally correct.

WHEN SPLITTING COLUMNS FORREASSEMBLY, WE RECOMMEND

SPLITTING & SPLINING THE COLUMN.PLEASE INDICATE SIZE & SHAPE OF

POST TO BE WRAPPED.

ADDITIONALCAP/BASE SETS

TAPERED COLUMNS

STOCK WOOD COLUMNS

CLASSICALCOLUMNSCOLONIALCOLUMNS

NON-TAPEREDCOLUMNS

Taper 1/3 of the way up and have an architecturally correct bead moulding.

Taper evenly from bottom to top and have a colonial bead moulding.

Diameter does not vary, nor is there any bead moulding.

All are available plain or fluted and come with a polyurethane capand base (unattached). Large stock columns come with a fiberglassor polyurethane cap and base. Please check your dimensions. Alldiameters are nominal. Overall height includes cap and base, allcolumns require field trimming to exact height requirements.

***IMPORTANT NOTES REGARDING STOCK WOOD COLUMNS***1.Be sure to follow all finishing and ventilation instructions, this

will insure a long life and is crucial to a successfulinstallation.

2. Stock columns are of a commodity grade, they will requiretrimming, filling and sanding. For a select furniture gradeproduct, we recommend the architecturally correct columns.They are more expensive, but are among the best on the markettoday and are "finish ready".

3. Architecturally correct, redwood, large stock and altered/modified stock columns are all made to order;they will require a deposit and production lead time.

SERVICES AVAILABLE

ADDITIONALCAP/BASE SETS

NON-TAPERED COLUMNS

SPLITTING & SPLINING CHARGES

ONCE A COLUMN IS SPLIT & SPLINED,IT IS NO LONGER STRUCTURAL.

DESCRIPTION PART # PRICE PERCOLUMN

Exteriorizing (priming outside with 1 coat oil base prime& asphaltium coat inside) N/A 8% Upcharge

Adjust column to a specified height DR-HEIGHT/ADJ $15.00Cut wood column at bead for decorative cap DR-BEAD/ADJ $15.00

Altering flutes from standard length DR-FLUTE/ALTER $15.00Splitting for pilaster (surface mount) application SEE CHART

Splitting & splining for reassembly around a structural post SEE CHART

PART # SIZE

SPLITTINGFEE

PRICE PERCOLUMN

SPLIT & SPLINEFEE

PRICE PERCOLUMN

CF9CF10CF12CF13CF14CF16CF18CF20CF22

8 FT.9 FT.10 FT.12 FT.14 FT.16 FT.18 FT.20 FT.22 FT.

15.0016.5018.7521.7526.2538.2557.0073.5089.25

80.2590.75

101.25121.00141.00161.25181.50202.50221.25

PART #FITS

COLUMNS PER SET

DR6DR8

DR10DR12

6"8"10"12"

27.9836.1543.1448.97

PART #FITS

COLUMNS PER SET

DR6NTPDR8NTP

DR10NTPDR12NTP

6"8"10"12"

33.8144.3152.4761.80


* FOR PLAIN COLUMNS:ADD A "P" AFTER THE PART NO.

*FOR FLUTED COLUMNS:ADD AN "F" AFTER THE PART NO.

*PLEASE NOTE: Overall Height & PriceIncludes Cap & Base.

PLAIN FLUTED

*When using columns on theexterior - for an 8% upcharge wecan prime the column 1 time &coat the lower 2 ft. of shaft inte-rior with asphaultium. Pleaseinquire.

PLEASE NOTE: All dimen-sions are considered accu-rate at time of printing.However, there may besome slight differences inthe future - If dimensionsare critical (particularly inthe cap and base), verifywhen placing your order.

ROUND TAPERED

COLONIAL WOOD COLUMNS WITH POLYURETHANE CAP & BASE

PAINT GRADE/FINGER JOINTED PINE (NOT RECOMMENDED FOR STAINING)Stock columns are of a commodity grade, they will require trimming, filling and sanding.

• Ideal for interior use.

• Gradual taper for a slenderlook.

PART #NOMINAL

SIZE WEIGHTPLAIN*EACH

FLUTED*EACH

DR68DR69

DR610

6" x 8'6" x 9'

6" x 10'

25 lbs.27 lbs.30 lbs.

123.54142.46158.05

146.92166.95188.10

DR88DR89

DR810DR812

8" x 8'8" x 9'

8" x 10'8" x12'


149.14166.95185.87297.17

176.97193.66209.24329.45

DR108DR109

DR1010DR1012

10" x 8'10" x 9'

10" x 10'10" x 12'


188.10210.36233.73302.74

221.49243.75266.01328.34

DR128DR129

DR1210DR1212

12" x 8'12" x 9'

12" x 10'12" x 12'


243.75267.12289.38377.31

278.25302.74323.88434.07

6" 8" 10" 12"BOTTOM

DIA. A 5-1/2" 7-1/4" 9-1/4" 11-1/4"

PLINTHB 8" 9-7/8" 11-7/8" 13-3/4"

C 1-1/4" 1-1/4" 1-1/4" 1-1/4"BASE

MOLD D 1-1/2" 1-1/2" 1-1/2" 1-1/2"

TOPDIA. E 4-3/4" 6-1/4" 8" 9-1/4"

SQUARECAP

F 7-1/2" 9-1/2" 11" 12"

G 1-1/4" 1-1/4" 1-1/4" 1-1/4"ROUND

CAP H 1-1/8" 1-1/8" 1-1/8" 1-1/8"

COLONIALBEAD I 1-1/4" 1-1/4" 1-1/4" 1-1/4"

BOTTOMFLUTE J 10-3/4" 10-3/4" 10-3/4" 10-3/4"

TOPFLUTE K 3-1/2" 3-1/2" 3-1/2" 3-1/2"

FLUTEDIA. L 3/4" 15/16" 15/16" 15/16"

LOADCAPACITY 4000 lbs. 6000 lbs. 7000 lbs. 8000 lbs.

WALLTHICKNESS 1-5/16" 1-5/16" 1-5/16" 1-5/16"

MAXIMUM SIZE POST COLUMN WILL WRAP AROUNDSQUARE N/A 2-1/2" 3-1/2" 4-1/2"ROUND 2" 3" 5" 6-1/2"


RESIN CAPITALS FOR USE WITH OUR TAPERED WOOD COLUMNS• HIGH LOAD BEARING CAPACITY • WATERPROOF • EASY TO INSTALL • INSECTPROOF

LOAD BEARING CAPACITY

HOW TO FINISH

It's Simple: No primer coat is necessary. Be sure to use a high quality paint and follow the manufacturer's instructions for best results.

Our capitals provide both a decorative as well as structural function. The results of independentlyoperated compressive strength testing and load bearing capacities of our capitals are listed in the chart:

NOTE: LARGER SIZES ARE AVAILABLE IN JESMONITE - PLEASE INQUIRE - FOR USE WITH OUR TAPERED COLUMNS ONLY - NOT FOR USE WITHOUR NON-TAPERED COLUMNS WE CANNOT ASSURE A PROPER FIT ON USE WITH OTHER MANUFACTURER'S COLUMNS

DIAMETER LOAD IN POUNDS6 Inches8 Inches10 Inches12 Inches

8,00010,00012,50015,000

NAME PART # FITS OUR COLUMN DIA. BOTTOM DIA. (A) HEIGHT (B) ABACUS (C) WEIGHT IN LBS. EACH

1 RomanIonic

CAP-6-I 6" 4-7/8" 2-1/4" 5-3/4" 4 81.90CAP-8-I 8" 6-5/8" 3" 7-7/8" 5-1/2 110.25CAP-10-I 10" 8-3/8" 4" 10" 12 137.55CAP-12-I 12" 10" 5-1/8" 12-1/4" 20 176.40

2 Scamozzi

CAP-6-S 6" 5-1/8" 2-1/2" 7-5/8" 5 82.95CAP-8-S 8" 6-1/4" 3" 9-3/4" 7-1/2 120.75CAP-10-S 10" 8-1/4" 3-5/8" 13-3/8" 15 142.80CAP-12-S 12" 9-7/8" 4-3/4" 16-1/4" 24 198.45

3 RomanCorinthian

CAP-6-C 6" 4-3/8" 7" 9-3/8" 8 88.20CAP-8-C 8" 6-1/2" 8-1/4" 11-3/8" 14 136.50CAP-10-C 10" 8-1/8" 11-3/16" 14-1/4" 26 192.15CAP-12-C 12" 9-1/2" 13-3/4" 19-1/2" 55 246.75

4 Temple ofWinds

CAP-6-TW 6" 5-1/8" 6-7/8" 7-7/8" 7 82.95CAP-8-TW 8" 6-1/2" 7-3/8" 10-3/8" 8 132.30CAP-10-TW 10" 8-1/8" 10" 13-3/4" 24 176.40CAP-12-TW 12" 10-1/8" 10-1/2" 15-3/4" 42 219.45

5 GreekErectheum

CAP-6-GE 6" 5" 3-1/4" 6-5/8" 5 77.70CAP-8-GE 8" 6-1/4" 3-5/8" 7-5/8" 6 110.25CAP-10-GE 10" 8" 5" 10-3/8" 20 137.55CAP-12-GE 12" 9-1/2" 5-5/8" 12" 26 181.65

PLEASE NOTE: All dimensions are considered accurate at time of printing. However, there may be some slight differences in the future - If dimen-sions are critical, verify when placing your order.

1

2

34

5

Temple of Winds Roman Corinthian Greek Erecthium Roman Ionic Scamozzi

The "B" dimension is the height added to your column height.

When using a decorative capital, column should be cut just above bead on necking for cap to look & fit correctly.


ROUND NON-TAPERED

COLONIAL WOOD COLUMNS WITH POLYURETHANE CAP & BASE

PAINT GRADE/FINGER JOINTED PINE (NOT RECOMMENDED FOR STAINING)Stock columns are of a commodity grade, they will require trimming, filling and sanding.

PLAIN FLUTED

ALL COLUMNS ARE AVAILABLE WITH ORWITHOUT BEAD MOULDING. PLEASESPECIFY "B" AFTER THE PART NO. ONLY IFBEAD MOULDING IS REQUIRED. THERE ISNO ADDITIONAL CHARGES FOR BEADMOULDING, HOWEVER, PLEASE ALLOW AD-DITIONAL TIME FOR PRODUCTION.


• No taper for a contemporarylook.




*When using columns on theexterior - for an 8% upcharge wecan prime the column 1 time &coat the lower 2 ft. of shaft inte-rior with asphaultium. Pleaseinquire.

PLEASE NOTE: All dimen-sions are considered accu-rate at time of printing.However, there may besome slight differences inthe future - If dimensionsare critical (particularly inthe cap and base), verifywhen placing your order.

PART # NOMINALSIZE WEIGHT PLAIN*

EACHFLUTED*

EACHDR68NTDR69NT

DR610NT

6" x 8'6" x 9'

6" x 10'

27 lbs.29 lbs.32 lbs.

154.71174.74195.89

182.53207.02234.84

DR88NTDR89NT

DR810NTDR812NT

8" x 8'8" x 9'

8" x 10'8" x12'


186.98207.02230.39335.01

222.60241.52262.67365.06

DR108NTDR109NT

DR1010NTDR1012NT

10" x 8'10" x 9'

10" x 10'10" x 12'


234.84263.78291.61351.71

276.02304.96331.67387.32

DR128NTDR129NT

DR1210NTDR1212NT

12" x 8'12" x 9'

12" x 10'12" x 12'


306.08332.79361.73424.05

347.26377.31406.25484.16

6" 8" 10" 12"BOTTOM

DIA. A 5-1/2" 7-1/4" 9-1/4" 11-1/4"

PLINTH B 8" 9-7/8" 11-7/8" 13-3/4"TOPDIA. C 5-1/2" 7-1/4" 9-1/4" 11-1/4"

SQUARECAP D 9" 9-13/16" 11-3/4" 13-3/4"

FLUTEDIA. E 3/4" 15/16" 15/16" 15/16"


WALLTHICKNESS 1-5/16" 1-5/16" 1-5/16" 1-5/16"

MAXIMUM SIZE POST COLUMN WILL WRAP AROUNDSQUARE N/A 3" 4" 5-5/8"ROUND 2-3/4" 4-1/2" 6-1/2" 8-1/2"


PLEASE NOTE: All dimensions are considered ac-curate at time of printing. However, there may besome slight differences in the future - If dimensionsare critical (particularly in the cap and base), verifywhen placing your order.

ROUND TAPERED

CLASSICAL WOOD COLUMNS WITH POLYURETHANE CAP & BASE

PAINT GRADE/FINGER JOINTED PINE (NOT RECOMMENDED FOR STAINING)

Stock columns are of a commodity grade, they will require trimming, filling and sanding.

PLAIN FLUTED

PART # NOMINALSIZE

PLAIN*EACH

FLUTED*EACH

DCR6X8DCR6X9

DCR6X10

6" x 8'6" x 9'

6" x 10'

134.67152.48170.29

159.16181.42203.68

DCR8X8DCR8X9

DCR8X10DCR8X12

8" x 8'8" x 9'

8" x 10'8" x12'

161.39180.31201.45310.53

193.66210.36228.17338.35

DCR10X8DCR10X9

DCR10X10DCR10X12

10" x 8'10" x 9'

10" x 10'10" x 12'

230.68253.76264.89322.77

240.41264.89289.38360.61

DCR12X8DCR12X9

DCR12X10DCR12X12

12" x 8'12" x 9'

12" x 10'12" x 12'

264.89290.49314.98429.62

301.62328.34352.82458.56

6" 8" 10" 12"BOTTOM

DIA. A 5-1/2" 7-1/4" 9-1/4" 11-1/4"

PLINTH B 8" 9-7/8" 11-7/8" 13-3/4"TOPDIA. C 4-3/4" 6-1/4" 8" 9-1/4"

SQUARECAP D 7-1/2" 9-1/2" 11" 12"

FLUTEDIA. E 3/4" 15/16" 15/16" 15/16"


WALL THICKNESS 1-5/16" 1-5/16" 1-5/16" 1-5/16"

MAXIMUM SIZE POST COLUMN WILL WRAP AROUNDSQUARE N/A 2-1/2" 3-1/2" 4-1/2"ROUND 2" 3" 5" 6-1/2"




*When using columns on the exterior- for an 8% upcharge we can prime thecolumn 1 time & coat the lower 2 ft. ofshaft interior with asphaultium. Pleaseinquire.


• Sharp taper for a classicallook.


PermaPost™SYNTHETIC PORCH POSTS

Molded from a urethane resin, these posts have a1-3/4” I.D., 20 gauge (.035” ) galvanized steel tubeinside, giving them a load bearing capacity of1300 lbs.

❑ Weatherproof &Insectproof

❑ Shipped White,Ready to Install

❑ Must Be PaintedWith Latex or OilBased Paint

❑ Trims & InstallsWith CommonCarpentry Tools

❑ Low Maintenance

PART # WIDTHOVERALLHEIGHT

TOP MIDDLE BOTTOM EACH

SPP58SPP59SPP68SPP69

4-1/8"4-1/8"5-1/8"5-1/8"

96-1/2"108-1/4"96-1/4"107-3/4"

16-1/4"24-1/2"16-1/2"24-1/2"

38-1/4"38-1/4"38-1/4"38-1/4"

42"45-1/2"41-1/2"

45"

78.0091.00100.00118.00


PVC POST COVERFOR 4” x 4” or 6” x 6” POSTS

Protects & Beautifies Unsightly Wood Posts

BEFORE AFTER

Installation Instructions:

1. Measure & cut both sides to length.2. Wrap post with pieces and starting at the bottom, snap

pieces together. (We recommend you hold one sideagainst the post while tapping the other side in with arubber mallet).

3. Glue trim collar sides to each other and post cover. Use PVCglue only.

• Covers posts up to 9 feet tall• Simple to install• Inexpensive• Maintenance Free• Strong, Resilient, Exterior Grade PVC• Easy to clean• Available in White• Two trim collars with each post cover

(Trim collars come as a 4 pc. set, PVCglue is recommended to join pcs. together).

PART # FOR POST SIZE DESCRIPTION PRICEPPC-49-WH 4" x 4" 9 Ft. Long Cover & 2 Trim Collars 43.00

PPC-TC-4-WH 4" x 4" Additional Trim Collar 4.90PPC-69-WH 6" x 6" 9 Ft. Long Cover & 2 Trim Collars 58.00

PPC-TC6-WH 6" x 6" Additional Trim Collar 5.45

SPECIFICATIONSPPC-49 PPC-69

MATERIAL PVC PVCMATERIAL THICKNESS 1/8" 1/8"

WALL THICKNESS 5/16" 5/16"INSIDE DIMENSIONS 3-3/4" 5-5/8"

OUTSIDE DIMENSIONS 4-5/16" 6-3/16"

TOP VIEW (4 interlocking pieces)


ARCHITECTURAL PRODUCTS INTRODUCES OUR NEW LINE OF

INTERIOR POST COVERSThe Perfect Solution To Cover Those Unsightly Basement Posts & Lollicolumns

The BurkwoodThe Burkwood is our premium post cover.It comes fluted and is square with cham-fered corners. Available in paintable MDFor unfinished solid stain grade Red Oak.Cap & base trim kit (ships unattached andunassembled) included with post cover.

Paint Grade MDF#BWD-PG$120.00 ea.

Stain Grade Red Oak(shown)#BWD-RO$190.00 ea.

(Base Trim Detail)

(Cap Trim Detail)

NOTE:Burkwood Post Covers canwrap up to a 4-1/2” round or3-3/4” square post.

*** Cap & Base Trim Kits Need To Be Assembled & Attached To Post On Site ***

Our standard line of unfinished interior post covers are octagonal and are availablepaint grade MDF and MDF with a Knotty Pine or Red Oak veneer. Finger jointed for astrong hold, all interior post covers ship in 2 halves for easy assembly around astandard 4” lollicolumn. Cap & base trim kits and drink shelves are sold separately.

Post Covers

Paint Grade MDF#PCOV-PG$89.00 ea.

Knotty Pine#PCOV-KP$149.00 ea.

Red Oak#PCOV-RO$159.00 ea.

(Cap & Base TrimKit Sold Sepa-rately)

Installation is Easy!• Cut post cover halves to desired height,• Using standard woodworking glue, run a bead down one side of each joint. Join halves around

post and clamp or tape. Allow 48 hours to dry.• Making sure cover is plumb, drill a 5/16” hole about 1-1/2” from each end of cover. Spray foam

insulation into holes to firm around post and help secure to floor & ceiling. Allow 3 hours to set.• Install cap & base trim kit and/or drink shelf, following the same process in which the post was

assembled.• Sand any rough or glued areas lightly with a fine grit sandpaper.• Finish with a quality oil based paint, stain or polyurethane, following manufacturer’s instructions

for application.

(Knotty Pine) (Red Oak)

Paintable#PCOV-PG-CB$31.00 kit

Knotty Pine#PCOV-KP-CB$35.00 kit

Red Oak#PCOV-RO-CB$39.00 kit

(Knotty Pine)

(Red Oak)

Cap & Base Trim Kit(comes unassembled)

Drink Shelf(Can be installed at any height you desire)Paintable#PCOV-PG-DS$69.00 kit

Knotty Pine#PCOV-KP-DS$75.00 kit

Red Oak#PCOV-RO-DS$79.00 kit

(Overall Width = 15”)

(Red Oak)NOTE:Standard PostCovers canwrap up to a4-1/4” round or3” square post.

columns

Documents

Transcript of columns