Coil detailed design and fabrication Winding and reaction
description
Transcript of Coil detailed design and fabrication Winding and reaction
![Page 1: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/1.jpg)
Coil detailed design and fabrication
Winding and reaction
F. Rondeaux
28/03/2012 1CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
![Page 2: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/2.jpg)
CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Outline
• Coils detailed geometry – Overview– Geometry details– Layer jump– Posts design– Electrical insulation
• Winding tooling and process
• Reaction toolingReaction process, impregnation tooling and process will be discussed by Juan Carlos in the next presentation
• Tests program
28/03/2012 2
![Page 3: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/3.jpg)
3CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Coils detailed geometry - overview
28/03/2012
1 color = 1 cable unit lenght (223 m / 253 m)
![Page 4: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/4.jpg)
4CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Coils geometry details• Adjustments in double pancake 1-2 and 3-4 following the last review:
Forced contact between the coils along the straight section: reduce Lss by 2mm for coil 3-4. The ramp angles remain identical everywhere (17°).
Avoid stress concentration around sharp edges in the ends: enlarge Los to 32mm for coil 3-4.
=> additional gaps of 0.24 mm are created along the ends (to be filled during the assembly process)
Inter-coils insulation thickness has been increased from 0.5 to 1.5 mm for the instrumentation traces, leading to increase the HW radiuses for coil 1-2
• RHW = 700 mm, aperture > 61 mm, htot < 200 mm
28/03/2012
700
1500
Additional gap
Los
Lss = 728 (coil 3-4)
![Page 5: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/5.jpg)
5CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Detailed 3D model of coil 3-4
28/03/2012
Draftsman:Jean-François Millot
View of the double pancake with its components
![Page 6: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/6.jpg)
6CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Detailed 3D model of coil 3-4
28/03/2012
Possibility of 2x0.2 mm steel shim obtain continuous contact all along the side of the coil
Reserved space max dimension of the reacted coil
1.5 mm shim fill the gap between coil and horseshoe (offset possible)
0.3 mm-thick alumina coating
Connection design
New rail design
![Page 7: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/7.jpg)
7CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Layer jump• In the HW zone, « double chicane » solution selected• Shim easier to position and fix, ensure better protection of the jump zone• Tests have been done:
28/03/2012
Experimental setup
Ref : report on layer jump test SAFIRS-00373-E (2011)
![Page 8: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/8.jpg)
8
Posts design
Stainless steel / Titanium* post
Magnetic steel post
28/03/2012 CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Layer jump template
* choice after the thermal tests
2 pins Φ16 fix the lateral position
Inter-posts positionning
![Page 9: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/9.jpg)
9CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Posts design
28/03/2012
Contact zones
![Page 10: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/10.jpg)
10CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Electrical insulation Glass fiber impregnated with epoxy resin
– Around cable: braid 0.2 mm– between layers: sheet of 0.5 mm– between double pancakes: enlarge to 1.5 mm to allow the
installation of the instrumentation (voltage taps connections + quench heaters)
Alumina coating - some parts are partially or totally covered: Rails
28/03/2012
Layer jump shim
Horseshoes
Posts
![Page 11: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/11.jpg)
11CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Electrical insulation
28/03/2012
0.5 mm Interlayer insulation
0.3 mm insulated trace0.9 mm insulation
1 mm insulation
1.5 mm
2 mm insulation
Vertical pad
7 mm intercoil insulation
4
3
1
2
3 mm insulation
![Page 12: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/12.jpg)
12CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Insulation between double pancakes = 1.5 mm
What we have todayin the prototype:
28/03/2012
What would be:
t = 1.5 mm
0.3 insulated trace+ 0.9 insulation+ 0.3 insulated trace-------- 1.5 inter-coil insulation
t = 0.9 mm
t = 0.3 mm
Post 3-4
Post 1-2t = 0.3 mm
![Page 13: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/13.jpg)
13
Fabrication process – main steps
28/03/2012 CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
• Conductor insulation
• Conductor preparation
• Winding
• Preparation for the heat treatment:
– Assembly of the reaction mold around the wound coil
– Transport to CERN
• Heat treatment
• Preparation for impregnation : – Nb3Sn/NbTi splice soldering– Instrumentation, ground insulation and
quench heaters integration
• Impregnation
• Coil assembly
• Magnet assembly
At Saclay
At CERN
(cf. Juan Carlos’ presentation)
![Page 14: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/14.jpg)
14
Upside down winding
• Simpler tooling
• Is the winding easier ? Yes
• Is the conductor stable and in good position? Yes
Winding tests
28/03/2012
But
Dishing
CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Ref: reports on winding tests SAFIRS-00152-B (2010) - SAFIRS-00372-C (2011)
![Page 15: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/15.jpg)
15CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Dishing• Before winding: 0.18 to 0.34 mm under tension of 10 daN• Test over 22 turns (4 with insulation) at 30 daN• Dishing increases turn after turn from 0.2 mm to 0.9 mm• Around 0.2 mm in the straight section• Slightly larger with flared ends (+ 0.1 mm)• Time-dependent
28/03/2012
![Page 16: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/16.jpg)
16CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Dishing
• Questions: Behavior of Nb3Sn similar regardless of the strand type? Impact on the field quality? On the mechanics?
• How to deal with it? Should we force the conductor flat? Adapt the molds?
28/03/2012
Dishing test results under 30 daN tension
![Page 17: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/17.jpg)
17
• Conductor insulation
• Conductor preparation
• Winding
• Preparation for the heat treatment:
– Assembly of the reaction mold around the wound coil
– Transport to CERN
• Heat treatment
• Preparation for impregnation : – Nb3Sn/NbTi splice soldering– Instrumentation, ground insulation and
quench heaters integration
• Impregnation
• Coil assembly
• Magnet assembly
Fabrication process – main steps
28/03/2012 CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
At Saclay
At CERN
(cf. Juan Carlos’ presentation)
![Page 18: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/18.jpg)
18CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Winding
28/03/2012
Winding table: 190 kg – 1.72 m * 0.45 m
Stock spool with cable : 60kg
Iron post: 34 kg
Horseshoes: 8 kg
Heavy pieces are equipped to be handle with crane
Winding machine existing at Saclay
![Page 19: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/19.jpg)
19CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Winding process - installation
28/03/2012
Post fixed on the winding table
The cable is installed layer 4 on the support spool on the tensioner layer 3 on the stock spool
The winding table is fixed on the winding machine - the table can be tilted to follow the geometry of the coil.
Protection sheet on table: 0.2 mm of mica
![Page 20: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/20.jpg)
20CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Winding layer 4
28/03/2012
The coil winding will start by forming the layer jump. It is protected with the layer jump shim.
The first layer is wound clockwise
![Page 21: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/21.jpg)
21CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Winding layer 4
28/03/2012
During winding, conductor turn will be maintain by lateral compression system using pressure wedges and rods.
Voltage tapes are introduced according to the instrumentation design.
At the end of the layer 4 winding, the bottom layer is maintained through rails and pressure wedges.
![Page 22: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/22.jpg)
22CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Winding layer 4
28/03/2012
The cable is fixed and cut.
The interlayer insulationis installed and fixed.
![Page 23: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/23.jpg)
23CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Winding layer 3
28/03/2012
The layer 3 is wound over the insulation
Horseshoes are adjusted, if necessary, pushed in place and the rails are fixed.
![Page 24: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/24.jpg)
24CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Winding completed
28/03/2012
![Page 25: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/25.jpg)
25CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Rails geometry
28/03/2012
Fixation of the rails on the horseshoes
Section of the coil
![Page 26: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/26.jpg)
26
• Conductor insulation
• Conductor preparation
• Winding
• Preparation for the heat treatment:
– Assembly of the reaction mold around the wound coil
– Transport to CERN
• Heat treatment
• Preparation for impregnation : – Nb3Sn/NbTi splice soldering– Instrumentation, ground insulation and
quench heaters integration
• Impregnation
• Coil assembly
• Magnet assembly
Fabrication process – main steps
28/03/2012 CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
At Saclay
At CERN
(cf. Juan Carlos’ presentation)
![Page 27: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/27.jpg)
27CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Reaction tooling
28/03/2012
The winding table is part of the reaction tooling.Top plates and pressure wedges are added to complete the tooling.Segmentation of the pressure wedges to allow replacement of the compression wedges.
This object will be send to CERN for the reaction
![Page 28: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/28.jpg)
28CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Reaction tooling
Reaction cavity
28/03/2012
Contact zones(define the cavity volume)
4% (respectively 2%) have been added to the dimensions with respect on bare cable thickness (respect. bare cable width).
![Page 29: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/29.jpg)
29CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Tests• Winding configuration: cf. slide 14
• Layer jump: cf. slide 7
• Dishing: cf. slides 15,16
• Mechanical test on stacks under preparation (waiting final insulated conductor)
• Compression at 300 K, at 4K• Thermal restraint
• Conductor behavior during heat treatment: cf. following slide
• Tests to be performed on the 2 types of conductor (PIT, IT)
• Construction of 2 full-scale prototypes with non annealed Cu cable1- Type 3-4 (42 turns + the smaller HW bends radius)2- Type 1-2
28/03/2012
![Page 30: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/30.jpg)
30CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Cable behavior during heat treatment
28/03/2012
1) PIT cable without "end mandrel"• The dishing is significantly increased after
heat treatment• No significant change in overall dimensions
2) PIT cable with "end mandrel"• The cable is unstable in straight parts• The end mandrel has moved (~0.6 mm) and
1.4 mm gap between cable and mandrel has been measured
• Dishing in the end part has disappeared
Preliminary tests
Ref: SAFIRS-00375-I (2011)
![Page 31: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/31.jpg)
31CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Conductor behavior during heat treatment
28/03/2012
New multi-turn dilatation test tooling (up to 10 turns)
3 materials : stainless steel, magnetic steel, titanium
Possibility to remove the central part of the mandrel
Set-up to react 3 molds in same time
![Page 32: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/32.jpg)
32CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Tests program• Winding configuration: cf. slide 14
• Layer jump: cf. slide 7
• Dishing: cf. slides 15,16
• Mechanical test on stacks under preparation (waiting final insulated conductor)
• Compression at 300 K, at 4K• Thermal contraction
• Conductor behavior during heat treatment: cf. slides 30, 31
• Tests to be performed on the 2 types of conductor (PIT, IT)
• Construction of 2 full-scale prototypes with non annealed Cu cable1- Type 3-4 (42 turns + the smallest HW bends radius) winding in July2- Type 1-2
28/03/2012
![Page 33: Coil detailed design and fabrication Winding and reaction](https://reader035.fdocuments.net/reader035/viewer/2022062316/5681671b550346895ddb9447/html5/thumbnails/33.jpg)
33CEA-Irfu-SACM-LEAS - F.Rondeaux - FRESCA 2 ESAC review
Conclusion
• The 3D model is available for the coil 3-4 available soon for the coil 1-2
• The winding tooling fabrication is on-going
• The winding of the first full scale prototype is foreseen for July
• The reaction mold is designed, waiting for approval
28/03/2012