CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF &...

24
Odometer Self-Diagnostics DTCs (Diagnostic Trouble Codes). Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM /HFSM, ECM and ABS DTCs. The Radio DTCs are retrieved through the radio and displayed on the radio display. See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch to Ignition and release odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word “diag” should then appear. Push the odometer reset button once and you will see the selection menu "PSSPtb" with the first P flashing. Each letter represents an area of the diagnostics module. The module that is flashing is the one you are going to check. To move from one letter (module) to the next, you push the odometer reset button one time. (from P to S to SP to t to b and back to P, etc.) P --> ECM (Electronic Control Module [EFI]) S --> TSM/TSSM/HFSM (Turn Signal/ Turn Signal Security Module/ Hands-free Security Module) SP --> speedometer t --> tachometer b --> ABS codes To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTCs the code will be displayed or the word “none” will appear if there are no DTCs. Push the odometer reset button again to view additional codes if they exist. Record the codes. If DTCs are NOT to be cleared, Press and release the odometer reset button. Part number of module will be displayed. NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until 'clear' is displayed. Release the odometer reset button. Turn OFF the ignition switch. Perform a road test then shut your bike down. Recheck the DTC’s again by repeating steps 1 to 7. If the code is current it will reappear. Historic DTCs are stored for 50 ignition cycles before cleared. The security lamp will only indicate the existence of historic DTCs for two ignition cycles. If DTCs are to be cleared for that module, press and hold the odometer reset button until 'clear' is displayed. Press and release the odometer reset button to continue to the next module. Turn Ignition switch to OFF to exit the diagnostic mode. Always correct the serial data codes (DTC U1300, U1301, U1016, U1040, U1064, U1097, U1255) before resolving any other codes. DTC's are assigned priority numbers to determine the order in which they should be diagnosed. The lowest priority number DTC should be diagnosed first and then continue with the next lowest DTC. WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM CÓDIGOS DE ERROS DE 2010 EM DIANTE

Transcript of CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF &...

Page 1: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

Odometer Self-Diagnostics DTCs (Diagnostic Trouble Codes).Speedometer Self Diagnostics: The speedometer is capable of displaying and clearing speedometer, tachometer, TSM/TSSM /HFSM, ECM and ABS DTCs. The Radio DTCs are retrieved through the radio and displayed on the radio display. See Table 2.

Turn Ignition switch to OFF & Run/Stop switch is to Run.Push odometer reset button in & hold.Turn ignition switch to Ignition and release odometer reset button. Background lighting should illuminate, speedometer needle should sweep its full range and indicator lamps (battery, security, low fuel, check engine and cruise) should illuminate. The word “diag” should then appear.Push the odometer reset button once and you will see the selection menu "PSSPtb" with the first P flashing.Each letter represents an area of the diagnostics module. The module that is flashing is the one you are going to check. To move from one letter (module) to the next, you push the odometer reset button one time. (from P to S to SP to t to b and back to P, etc.)P --> ECM (Electronic Control Module [EFI])S --> TSM/TSSM/HFSM (Turn Signal/ Turn Signal Security Module/ Hands-free Security Module)SP --> speedometert --> tachometerb --> ABS codes

To get the DTC within an area of diagnostics, push and hold the odometer reset button in for 5 seconds and release. If there are any DTCs the code will be displayed or the word “none” will appear if there are no DTCs. Push the odometer reset button again to view additional codes if they exist.Record the codes.If DTCs are NOT to be cleared, Press and release the odometer reset button. Part number of module will be displayed.NOTE: To determine if a code is current or historic, clear the displayed code by pushing in and holding the odometer reset button ( longer than 5 seconds) until 'clear' is displayed. Release the odometer reset button. Turn OFF the ignition switch. Perform a road test then shut your bike down. Recheck the DTC’s again by repeating steps 1 to 7. If the code is current it will reappear. Historic DTCs are stored for 50 ignition cycles before cleared. The security lamp will only indicate the existence of historic DTCs for two ignition cycles.

If DTCs are to be cleared for that module, press and hold the odometer reset button until 'clear' is displayed.Press and release the odometer reset button to continue to the next module.Turn Ignition switch to OFF to exit the diagnostic mode.Always correct the serial data codes (DTC U1300, U1301, U1016, U1040, U1064, U1097, U1255) before resolving any other codes. DTC's are assigned priority numbers to determine the order in which they should be diagnosed. The lowest priority number DTC should be diagnosed first and then continue with the next lowest DTC.

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

Page 2: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

Diagnostic Trouble Codes -DTCs- DTC: B0562FAULT CONDITION: Battery Voltage LowSOLUTION: 3.6 DTC B0563, P0562, P0563

DTC: B0563FAULT CONDITION: Battery Voltage HighPRIORITY ORDER: 138SOLUTION: 3.6 DTC B0563, P0562, P0563

DTC: B1004FAULT CONDITION: Fuel Level Sending Unit LowPRIORITY ORDER: 145SOLUTION: 4.2 DTC B1004, B1005

DTC: B1005FAULT CONDITION: Fuel Level Sending Unit High/OpenPRIORITY ORDER: 146SOLUTION: 4.2 DTC B1004, B1005

DTC: B1006FAULT CONDITION: Accessory Line OvervoltagePRIORITY ORDER: 143SOLUTION: 3.7 DTC B1006, B1007

DTC: B1007FAULT CONDITION: Ignition Line OvervoltagePRIORITY ORDER: 142SOLUTION: 3.7 DTC B1006, B1007

DTC: B1008FAULT CONDITION: Trip Odometer Reset Switch ClosedPRIORITY ORDER: 144SOLUTION: 4.3 DTC B1008

DTC: B1121FAULT CONDITION: Left Turn Output FaultPRIORITY ORDER: 129SOLUTION: 5.11 DTC B1121,B1122,B1123,B1124,B1125,B1126

DTC: B1122FAULT CONDITION: Right Turn Output FaultPRIORITY ORDER: 130SOLUTION: 5.11 DTC B1121,B1122,B1123,B1124,B1125,B1126

DTC: B1123FAULT CONDITION: Left Turn Signal short-to-groundPRIORITY ORDER: 131SOLUTION: 5.11 DTC B1121,B1122,B1123,B1124,B1125,B1126

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

Page 3: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

DTC: B1124FAULT CONDITION: Right Turn Signal short-to-groundPRIORITY ORDER: 132SOLUTION: 5.11 DTC B1121,B1122,B1123,B1124,B1125,B1126

DTC: B1125FAULT CONDITION: Left Turn Signal short-to-voltagePRIORITY ORDER: 133SOLUTION: 5.11 DTC B1121,B1122,B1123,B1124,B1125,B1126

DTC: B1126FAULT CONDITION: Right Turn Signal short-to-voltagePRIORITY ORDER: 134SOLUTION: 5.11 DTC B1121,B1122,B1123,B1124,B1125,B1126

DTC: B1131FAULT CONDITION: Alarm Output LowPRIORITY ORDER: 139SOLUTION: 5.18 DTC B1131,B1132

DTC: B1132FAULT CONDITION: Alarm Output HighPRIORITY ORDER: 140SOLUTION: 5.18 DTC B1131,B1132

DTC: B1134FAULT CONDITION: Starter Relay Output HighPRIORITY ORDER: 128SOLUTION: 5.19 DTC B1134

DTC: B1135FAULT CONDITION: Accelerometer FaultPRIORITY ORDER: 23SOLUTION: 5.12 DTC B1135,B1136,B1141,B1142

DTC: B1136FAULT CONDITION: Accelerometer tip-over self-test faultPRIORITY ORDER: 24SOLUTION: 5.12 DTC B1135,B1136,B1141,B1142

DTC: B1141FAULT CONDITION: Ignition Switch open/lowPRIORITY ORDER: 141SOLUTION: 5.12 DTC B1135,B1136,B1141,B1142

DTC: B1142FAULT CONDITION: Internal FaultPRIORITY ORDER: 22SOLUTION: 5.12 DTC B1135,B1136,B1141,B1142

CÓDIGOS DE ERROS DE2010 EM DIANTE

Page 4: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

DTC: B1143FAULT CONDITION: Security antenna short-to-groundPRIORITY ORDER: 135SOLUTION: 5.20 DTC B1143,B1144,B1145

DTC: B1144FAULT CONDITION: Security antenna short-to-batteryPRIORITY ORDER: 136SOLUTION: 5.20 DTC B1143,B1144,B1145

DTC: B1145FAULT CONDITION: Security antenna openPRIORITY ORDER: 137SOLUTION: 5.20 DTC B1143,B1144,B1145

DTC: B1151FAULT CONDITION: Sidecar BAS short to groundPRIORITY ORDER: 25SOLUTION: See Trike or Sidecar supp manual

DTC: B1152FAULT CONDITION: Sidecar BAS short to batteryPRIORITY ORDER: 26SOLUTION: See Trike or Sidecar supp manual

DTC: B1153FAULT CONDITION: Sidecar BAS Out of RangePRIORITY ORDER: 27SOLUTION: See Trike or Sidecar supp manual

DTC: B1154FAULT CONDITION: Clutch switch short-to-groundPRIORITY ORDER: 28SOLUTION: 5.21 DTC B1154,B1155

DTC: B1155FAULT CONDITION: Neutral Switch short-to-groundPRIORITY ORDER: 29SOLUTION: 5.21 DTC B1154,B1155

DTC: C0562FAULT CONDITION: System Voltage LowPRIORITY ORDER: 111SOLUTION: 3.6 DTC B0563,P0562,P0563

DTC: C0563FAULT CONDITION: System Voltage HighPRIORITY ORDER: 112SOLUTION: 3.6 DTC B0563,P0562,P0563

CÓDIGOS DE ERROS DE2010 EM DIANTE

Page 5: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: C1014FAULT CONDITION: ECU internal solid state relay faultPRIORITY ORDER: 105SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121

DTC: C1017FAULT CONDITION: Pump Motor Power Circuit Open FaultPRIORITY ORDER: 110SOLUTION: 7.2 DTC C1017,C1018

DTC: C1018FAULT CONDITION: Pump motor ground high resistance faultPRIORITY ORDER: 109SOLUTION: 7.2 DTC C1017,C1018

DTC: C1021FAULT CONDITION: Front wheel speed sensor always equals zero kphPRIORITY ORDER: 115SOLUTION: 7.3 DTC C1021,C1023

DTC: C1023FAULT CONDITION: Rear wheel speed sensor always equals zero kphPRIORITY ORDER: 116SOLUTION: 7.3 DTC C1021,C1023

DTC: C1025FAULT CONDITION: Front wheel speed sensor signal intermittentPRIORITY ORDER: 117SOLUTION: 7.4 DTC C1025,C1027,C1206,C1208

DTC: C1027FAULT CONDITION: Rear wheel speed sensor signal intermittentPRIORITY ORDER: 118SOLUTION: 7.4 DTC C1025,C1027,C1206,C1208

DTC: C1032FAULT CONDITION: Front wheel speed sensor circuit open or shortedPRIORITY ORDER: 113SOLUTION: 7.5 DTC C1032,C1034

DTC: C1034FAULT CONDITION: Rear wheel speed sensor circuit open or shortedPRIORITY ORDER: 114SOLUTION: 7.5 DTC C1032,C1034

DTC: C1042FAULT CONDITION: Pump motor openPRIORITY ORDER: 107SOLUTION: 7.6 DTC C1042,C1043

Page 6: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: C1043FAULT CONDITION: Pump motor stalledPRIORITY ORDER: 108SOLUTION: 7.6 DTC C1042,C1043

DTC: C1055FAULT CONDITION: ECU internal faultPRIORITY ORDER: 96SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121

DTC: C1056FAULT CONDITION: ECU internal fault - sold state relay shorted ONPRIORITY ORDER: 97SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121

DTC: C1057FAULT CONDITION: ECU internal fault - solid state relay shorted to groundPRIORITY ORDER: 98SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121

DTC: C1061FAULT CONDITION: ECU internal fault - front apply solenoidPRIORITY ORDER: 99SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121

DTC: C1062FAULT CONDITION: ECU internal fault - front release solenoidPRIORITY ORDER: 100SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121

DTC: C1065FAULT CONDITION: ECU internal fault - rear apply solenoidPRIORITY ORDER: 101SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121

DTC: C1066FAULT CONDITION: ECU internal fault - rear release solenoidPRIORITY ORDER: 102SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121

DTC: C1094FAULT CONDITION: Front brake switch always onPRIORITY ORDER: 121SOLUTION: 7.7 DTC C1094

DTC: C1095FAULT CONDITION: Front brake switch openPRIORITY ORDER: 122SOLUTION: 7.8 DTC C1095

Page 7: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: C1118FAULT CONDITION: ECU internal fault - front apply solenoid correlationPRIORITY ORDER: 103SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121

DTC: C1121FAULT CONDITION: ECU internal fault - rear apply solenoid correlationPRIORITY ORDER: 104SOLUTION: 7.15 DTC C1014,C1055-C1066,C1118,C1121

DTC: C1151FAULT CONDITION: Front wheel ABS release too longPRIORITY ORDER: 126SOLUTION: 7.9 DTC C1151

DTC: C1153FAULT CONDITION: Rear wheel ABS release too longPRIORITY ORDER: 127SOLUTION: 7.10 DTC C1153

DTC: C1158FAULT CONDITION: Calibration programming requiredPRIORITY ORDER: 106SOLUTION: 7.11 DTC C1158

DTC: C1206FAULT CONDITION: Front wheel speed sensor frequency out of rangePRIORITY ORDER: 119SOLUTION: 7.4 DTC C1025,C1027,C1206,C1208

DTC: C1208FAULT CONDITION: Rear wheel speed sensor frequency out of rangePRIORITY ORDER: 120SOLUTION: 7.4 DTC C1025,C1027,C1206,C1208

DTC: C1212FAULT CONDITION: Front or Rear brake not applied with decelPRIORITY ORDER: 125SOLUTION: 7.12 DTC C1212

DTC: C1214FAULT CONDITION: Rear brake switch always onPRIORITY ORDER: 123SOLUTION: 7.13 DTC C1214

DTC: C1216FAULT CONDITION: Rear brake switch openPRIORITY ORDER: 124SOLUTION: 7.14 DTC C1216

Page 8: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: P0031FAULT CONDITION: O2 heater low/openPRIORITY ORDER: 82SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154

DTC: P0032FAULT CONDITION: O2 heater shorted/highPRIORITY ORDER: 82SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154

DTC: P0106FAULT CONDITION: MAP Sensor Rate of Range Error

DTC: P0107FAULT CONDITION: Map Sensor Open/LowPRIORITY ORDER: 19SOLUTION: 6.4 DTC P0107,P0108,P0112,P0113

DTC: P0108FAULT CONDITION: Map Sensor HighPRIORITY ORDER: 20SOLUTION: 6.4 DTC P0107,P0108,P0112,P0113

DTC: P0112FAULT CONDITION: IAT Sensor Voltage LowPRIORITY ORDER: 58SOLUTION: 6.4 DTC P0107,P0108,P0112,P0113

DTC: P0113FAULT CONDITION: IAT Sensor Voltage Open/HighPRIORITY ORDER: 59SOLUTION: 6.4 DTC P0107,P0108,P0112,P0113

DTC: P0117FAULT CONDITION: ET Sensor Voltage LowPRIORITY ORDER: 56SOLUTION: 6.5 DTC P0117,P0118

DTC: P0118FAULT CONDITION: ET Sensor Voltage Open/HighPRIORITY ORDER: 57SOLUTION: 6.5 DTC P0117,P0118

DTC: P0120FAULT CONDITION: Throttle position sensor 1 range errorPRIORITY ORDER: 38SOLUTION: 6.6 DTC P0120,P0122,P0123,P0220,P0222,P0223

Page 9: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: P0122FAULT CONDITION: TP Sensor Open/LowPRIORITY ORDER: 40SOLUTION: 6.6 DTC P0120,P0122,P0123,P0220,P0222,P0223

DTC: P0031FAULT CONDITION: O2 heater low/openPRIORITY ORDER: 82SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154

DTC: P0032FAULT CONDITION: O2 heater shorted/highPRIORITY ORDER: 82SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154

DTC: P0106FAULT CONDITION: MAP Sensor Rate of Range Error

DTC: P0107FAULT CONDITION: Map Sensor Open/LowPRIORITY ORDER: 19SOLUTION: 6.4 DTC P0107,P0108,P0112,P0113

DTC: P0108FAULT CONDITION: Map Sensor HighPRIORITY ORDER: 20SOLUTION: 6.4 DTC P0107,P0108,P0112,P0113

DTC: P0112FAULT CONDITION: IAT Sensor Voltage LowPRIORITY ORDER: 58SOLUTION: 6.4 DTC P0107,P0108,P0112,P0113

DTC: P0113FAULT CONDITION: IAT Sensor Voltage Open/HighPRIORITY ORDER: 59SOLUTION: 6.4 DTC P0107,P0108,P0112,P0113

DTC: P0117FAULT CONDITION: ET Sensor Voltage LowPRIORITY ORDER: 56SOLUTION: 6.5 DTC P0117,P0118

DTC: P0118FAULT CONDITION: ET Sensor Voltage Open/HighPRIORITY ORDER: 57SOLUTION: 6.5 DTC P0117,P0118

Page 10: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: P0120FAULT CONDITION: Throttle position sensor 1 range errorPRIORITY ORDER: 38SOLUTION: 6.6 DTC P0120,P0122,P0123,P0220,P0222,P0223

DTC: P0122FAULT CONDITION: TP Sensor Open/LowPRIORITY ORDER: 40SOLUTION: 6.6 DTC P0120,P0122,P0123,P0220,P0222,P0223

DTC: P0123FAULT CONDITION: TP Sensor HighPRIORITY ORDER: 41SOLUTION: 6.6 DTC P0120,P0122,P0123,P0220,P0222,P0223

DTC: P0131FAULT CONDITION: Front O2 sensor low (lean)PRIORITY ORDER: 84SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154

DTC: P0132FAULT CONDITION: Front O2 sensor high (rich)PRIORITY ORDER: 86SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154

DTC: P0134FAULT CONDITION: Front O2 sensor open/not respondingPRIORITY ORDER: 88SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154

DTC: P0151FAULT CONDITION: Rear O2 sensor low (lean)PRIORITY ORDER: 85SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154

DTC: P0152FAULT CONDITION: Rear O2 sensor high (rich)PRIORITY ORDER: 87SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154

DTC: P0154FAULT CONDITION: Rear O2 sensor open/not respondingPRIORITY ORDER: 89SOLUTION: 6.7 DTC P0031,P0032,P0131,P0132,P0134,P0151,P0152,P0154

DTC: P0220FAULT CONDITION: Throttle position sensor 2 range errorPRIORITY ORDER: 39SOLUTION: 6.6 DTC P0120,p0122,P0123,P0220,P0222,P0223

Page 11: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: P0222FAULT CONDITION: Throttle position sensor 2 low/openPRIORITY ORDER: 42SOLUTION: 6.6 DTC P0120,p0122,P0123,P0220,P0222,P0223

DTC: P0223FAULT CONDITION: Throttle position sensor 2 highPRIORITY ORDER: 43SOLUTION: 6.6 DTC P0120,p0122,P0123,P0220,P0222,P0223

DTC: P0261FAULT CONDITION: Front Injector Open/LowPRIORITY ORDER: 66SOLUTION: 6.8 DTC P0261,P0262,P0263,P0264

DTC: P0262FAULT CONDITION: Front Injector HighPRIORITY ORDER: 68SOLUTION: 6.8 DTC P0261,P0262,P0263,P0264

DTC: P0263FAULT CONDITION: Rear Injector Open/LowPRIORITY ORDER: 67SOLUTION: 6.8 DTC P0261,P0262,P0263,P0264

DTC: P0264FAULT CONDITION: Rear Injector HighPRIORITY ORDER: 69SOLUTION: 6.8 DTC P0261,P0262,P0263,P0264

DTC: P0373FAULT CONDITION: CKP Sensor IntermittentPRIORITY ORDER: 18SOLUTION: 6.9 DTC P0373,P0374

DTC: P0374FAULT CONDITION: CKP Sensor Synch ErrorPRIORITY ORDER: 21SOLUTION: 6.9 DTC P0373,P0374

DTC: P0444FAULT CONDITION: Purge control open/lowPRIORITY ORDER: 77SOLUTION: 6.10 DTC P0444,P0445

DTC: P0445FAULT CONDITION: Purge control highPRIORITY ORDER: 78SOLUTION: 6.10 DTC P0444,P0445

Page 12: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: P0501FAULT CONDITION: VSS LowPRIORITY ORDER: 72SOLUTION: 6.11 DTC P0501,P0502

DTC: P0502FAULT CONDITION: VSS High/OpenPRIORITY ORDER: 73SOLUTION: 6.11 DTC P0501,P0502

DTC: P0505FAULT CONDITION: Loss of Idle Sped ControlPRIORITY ORDER: 76SOLUTION: 6.12 DTC P0505

DTC: P0562FAULT CONDITION: Battery Voltage LowPRIORITY ORDER: 70SOLUTION: 3.6 DTC B0563,P0562,P0563

DTC: P0563FAULT CONDITION: Battery Voltage HighPRIORITY ORDER: 71SOLUTION: 3.6 BTC B0563,P0562,P0563

DTC: P0572FAULT CONDITION: Brake switch lowPRIORITY ORDER: 55SOLUTION: 6.13 DTC P0572

DTC: P0577FAULT CONDITION: Cruise control input highPRIORITY ORDER: 93SOLUTION: 5.4 DTC P0577

DTC: P0602FAULT CONDITION: Calibration Memory Error

DTC: P0603FAULT CONDITION: ECM EEPROM ErrorPRIORITY ORDER: 2SOLUTION: 6.14 DTC P0603,P0605

DTC: P0604FAULT CONDITION: RAM Failure

DTC: P0605FAULT CONDITION: ECM Flash ErrorPRIORITY ORDER: 1SOLUTION: 6.14 DTC P0603,P0605

Page 13: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: P0607FAULT CONDITION: Converter Error

DTC: P0641FAULT CONDITION: 5V ref 1 out of rangePRIORITY ORDER: 16SOLUTION: 6.15 DTC P0641,P0651

DTC: P0651FAULT CONDITION: 5V ref 2 out of rangePRIORITY ORDER: 17SOLUTION: 6.15 DTC P0641,P0651

DTC: P0661FAULT CONDITION: Intake solenoid low/openPRIORITY ORDER: 48SOLUTION: 6.15 DTC P0641,P0651

DTC: P0662FAULT CONDITION: Intake solenoid high/shortedPRIORITY ORDER: 49SOLUTION: 6.15 DTC P0641,P0651

DTC: P1001FAULT CONDITION: System Relay Coil Open/LowPRIORITY ORDER: 12SOLUTION: 6.16 DTC P1001,P1002,P1003,P1004

DTC: P1002FAULT CONDITION: System relay Coil High/ShortedPRIORITY ORDER: 11SOLUTION: 6.16 DTC P1001,P1002,P1003,P1004

DTC: P1003FAULT CONDITION: System relay Contacts OpenPRIORITY ORDER: 10SOLUTION: 6.16 DTC P1001,P1002,P1003,P1004

DTC: P1004FAULT CONDITION: System Relay Contacts ClosedPRIORITY ORDER: 13SOLUTION: 6.16 DTC P1001,P1002,P1003,P1004

DTC: P1009FAULT CONDITION: Incorrect PasswordPRIORITY ORDER: 14SOLUTION: 6.17 DTC P1009,P1010

Page 14: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: P1010FAULT CONDITION: Missing PasswordPRIORITY ORDER: 15SOLUTION: 6.17 DTC P1009,P1010

DTC: P1270FAULT CONDITION: Twistgrip position sensor 2 A/D validation errorPRIORITY ORDER: 31SOLUTION: 6.18 DTC P1270

DTC: P1351FAULT CONDITION: Front Ignition Open/LowPRIORITY ORDER: 60SOLUTION: 6.19 DTC P1351,P1352,P1354,P1355

DTC: P1352FAULT CONDITION: Front Ignition Coil High/ShortedPRIORITY ORDER: 62SOLUTION: 6.19 DTC P1351,P1352,P1354,P1355

DTC: P1353FAULT CONDITION: Front Cylinder No CombustionPRIORITY ORDER: 75SOLUTION: 6.20 DTC P1353,P1356,P1357,P1358

DTC: P1354FAULT CONDITION: Rear Ignition Coil Open/LowPRIORITY ORDER: 61SOLUTION: 6.19 DTC P1351,P1352,P1354,P1355

DTC: P1355FAULT CONDITION: Rear Ignition Coil High/ShortedPRIORITY ORDER: 63SOLUTION: 6.19 DTC P1351,P1352,P1354,P1355

DTC: P1356FAULT CONDITION: Rear Cylinder No CombustionPRIORITY ORDER: 74SOLUTION: 6.20 DTC P1353,P1356,P1357,P1358

DTC: P1357FAULT CONDITION: Intermittent Secondary FrontPRIORITY ORDER: 64SOLUTION: 6.20 DTC P1353,P1356,P1357,P1358

DTC: P1358FAULT CONDITION: Intermittent Secondary RearPRIORITY ORDER: 65SOLUTION: 6.20 DTC P1353,P1356,P1357,P1358

Page 15: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: P1475FAULT CONDITION: Exhaust position actuation errorPRIORITY ORDER: 79SOLUTION: 6.21 DTC P1475,P1477,P1478

DTC: P1477FAULT CONDITION: Exhaust actuator low/openPRIORITY ORDER: 80SOLUTION: 6.21 DTC P1475,P1477,P1478

DTC: P1478FAULT CONDITION: Exhaust actuator hight/shortedPRIORITY ORDER: 81SOLUTION: 6.21 DTC P1475,P1477,P1478

DTC: P1501FAULT CONDITION: JSS lowPRIORITY ORDER: 53SOLUTION: 6.22 DTC P1501,P1502

DTC: P1502FAULT CONDITION: JSS highPRIORITY ORDER: 54SOLUTION: 6.22 DTC P1501,P1502

DTC: P1510FAULT CONDITION: Throttle actuator control limited performancePRIORITY ORDER: 90SOLUTION: 6.23 DTC P1510,P1511,P1512

DTC: P1511FAULT CONDITION: Throttle actuator limited power management modePRIORITY ORDER: 91SOLUTION: 6.23 DTC P1510,P1511,P1512

DTC: P1512FAULT CONDITION: Throttle actuator control forced idle modePRIORITY ORDER: 92SOLUTION: 6.23 DTC P1510,P1511,P1512

DTC: P1514FAULT CONDITION: Throttle actuator control system airflow faultPRIORITY ORDER: 51SOLUTION: 6.24 DTC P1514

DTC: P1600FAULT CONDITION: TCA module - internal faultPRIORITY ORDER: 30SOLUTION: 6.25 DTC P1600

Page 16: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: P1475FAULT CONDITION: Exhaust position actuation errorPRIORITY ORDER: 79SOLUTION: 6.21 DTC P1475,P1477,P1478

DTC: P1477FAULT CONDITION: Exhaust actuator low/openPRIORITY ORDER: 80SOLUTION: 6.21 DTC P1475,P1477,P1478

DTC: P1478FAULT CONDITION: Exhaust actuator hight/shortedPRIORITY ORDER: 81SOLUTION: 6.21 DTC P1475,P1477,P1478

DTC: P1501FAULT CONDITION: JSS lowPRIORITY ORDER: 53SOLUTION: 6.22 DTC P1501,P1502

DTC: P1502FAULT CONDITION: JSS highPRIORITY ORDER: 54SOLUTION: 6.22 DTC P1501,P1502

DTC: P1510FAULT CONDITION: Throttle actuator control limited performancePRIORITY ORDER: 90SOLUTION: 6.23 DTC P1510,P1511,P1512

DTC: P1511FAULT CONDITION: Throttle actuator limited power management modePRIORITY ORDER: 91SOLUTION: 6.23 DTC P1510,P1511,P1512

DTC: P1512FAULT CONDITION: Throttle actuator control forced idle modePRIORITY ORDER: 92SOLUTION: 6.23 DTC P1510,P1511,P1512

DTC: P1514FAULT CONDITION: Throttle actuator control system airflow faultPRIORITY ORDER: 51SOLUTION: 6.24 DTC P1514

DTC: P1600FAULT CONDITION: TCA module - internal faultPRIORITY ORDER: 30SOLUTION: 6.25 DTC P1600

Page 17: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: P1655FAULT CONDITION: ACR solenoid lowPRIORITY ORDER: 94SOLUTION: 6.26 DTC P1655,P1656

DTC: P1656FAULT CONDITION: ACR solenoid highPRIORITY ORDER: 95SOLUTION: 6.26 DTC P1655,P1656

DTC: P2100FAULT CONDITION: Throttle actuator control motor circuit / openPRIORITY ORDER: 46SOLUTION: 6.27 DTC P2100,P2101,P2102,P2103

DTC: P2101FAULT CONDITION: Throttle actuator control motor circuit - range errorPRIORITY ORDER: 47SOLUTION: 6.27 DTC P2100,P2101,P2102,P2103

DTC: P2102FAULT CONDITION: Throttle actuator control motor circuit - lowPRIORITY ORDER: 48SOLUTION: 6.27 DTC P2100,P2101,P2102,P2103

DTC: P2103FAULT CONDITION: Throttle actuator control motor circuit - highPRIORITY ORDER: 49SOLUTION: 6.27 DTC P2100,P2101,P2102,P2103

DTC: P2105FAULT CONDITION: Throttle actuator control system - forced engine shutdownPRIORITY ORDER: 52SOLUTION: 6.28 DTC P2105,P2107

DTC: P2107FAULT CONDITION: Throttle actuator control module processorPRIORITY ORDER: 32SOLUTION: 6.28 DTC P2105,P2107

DTC: P2119FAULT CONDITION: Throttle actuator control system - throttle return errorPRIORITY ORDER: 45SOLUTION: 6.29 DTC P2119

DTC: P2122FAULT CONDITION: Twistgrip position sensor 1 low/openPRIORITY ORDER: 33SOLUTION: 6.30 DTC P2122,P2123,P2127,P2128

Page 18: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: P1655FAULT CONDITION: ACR solenoid lowPRIORITY ORDER: 94SOLUTION: 6.26 DTC P1655,P1656

DTC: P1656FAULT CONDITION: ACR solenoid highPRIORITY ORDER: 95SOLUTION: 6.26 DTC P1655,P1656

DTC: P2100FAULT CONDITION: Throttle actuator control motor circuit / openPRIORITY ORDER: 46SOLUTION: 6.27 DTC P2100,P2101,P2102,P2103

DTC: P2101FAULT CONDITION: Throttle actuator control motor circuit - range errorPRIORITY ORDER: 47SOLUTION: 6.27 DTC P2100,P2101,P2102,P2103

DTC: P2102FAULT CONDITION: Throttle actuator control motor circuit - lowPRIORITY ORDER: 48SOLUTION: 6.27 DTC P2100,P2101,P2102,P2103

DTC: P2103FAULT CONDITION: Throttle actuator control motor circuit - highPRIORITY ORDER: 49SOLUTION: 6.27 DTC P2100,P2101,P2102,P2103

DTC: P2105FAULT CONDITION: Throttle actuator control system - forced engine shutdownPRIORITY ORDER: 52SOLUTION: 6.28 DTC P2105,P2107

DTC: P2107FAULT CONDITION: Throttle actuator control module processorPRIORITY ORDER: 32SOLUTION: 6.28 DTC P2105,P2107

DTC: P2119FAULT CONDITION: Throttle actuator control system - throttle return errorPRIORITY ORDER: 45SOLUTION: 6.29 DTC P2119

DTC: P2122FAULT CONDITION: Twistgrip position sensor 1 low/openPRIORITY ORDER: 33SOLUTION: 6.30 DTC P2122,P2123,P2127,P2128

Page 19: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: P1655FAULT CONDITION: ACR solenoid lowPRIORITY ORDER: 94SOLUTION: 6.26 DTC P1655,P1656

DTC: P1656FAULT CONDITION: ACR solenoid highPRIORITY ORDER: 95SOLUTION: 6.26 DTC P1655,P1656

DTC: P2100FAULT CONDITION: Throttle actuator control motor circuit / openPRIORITY ORDER: 46SOLUTION: 6.27 DTC P2100,P2101,P2102,P2103

DTC: P2101FAULT CONDITION: Throttle actuator control motor circuit - range errorPRIORITY ORDER: 47SOLUTION: 6.27 DTC P2100,P2101,P2102,P2103

DTC: P2102FAULT CONDITION: Throttle actuator control motor circuit - lowPRIORITY ORDER: 48SOLUTION: 6.27 DTC P2100,P2101,P2102,P2103

DTC: P2103FAULT CONDITION: Throttle actuator control motor circuit - highPRIORITY ORDER: 49SOLUTION: 6.27 DTC P2100,P2101,P2102,P2103

DTC: P2105FAULT CONDITION: Throttle actuator control system - forced engine shutdownPRIORITY ORDER: 52SOLUTION: 6.28 DTC P2105,P2107

DTC: P2107FAULT CONDITION: Throttle actuator control module processorPRIORITY ORDER: 32SOLUTION: 6.28 DTC P2105,P2107

DTC: P2119FAULT CONDITION: Throttle actuator control system - throttle return errorPRIORITY ORDER: 45SOLUTION: 6.29 DTC P2119

DTC: P2122FAULT CONDITION: Twistgrip position sensor 1 low/openPRIORITY ORDER: 33SOLUTION: 6.30 DTC P2122,P2123,P2127,P2128

Page 20: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: P2123FAULT CONDITION: Twistgrip position sensor 1 highPRIORITY ORDER: 34SOLUTION: 6.30 DTC P2122,P2123,P2127,P2128

DTC: P2127FAULT CONDITION: Twistgrip position sensor 2 low/openPRIORITY ORDER: 35SOLUTION: 6.30 DTC P2122,P2123,P2127,P2128

DTC: P2128FAULT CONDITION: Twistgrip position sensor 2 highPRIORITY ORDER: 36SOLUTION: 6.30 DTC P2122,P2123,P2127,P2128

DTC: P2135FAULT CONDITION: Throttle position sensor correlation errorPRIORITY ORDER: 44SOLUTION: 6.31 DTC P2135,P2138

DTC: P2138FAULT CONDITION: Twistgrip position sensor correlation errorPRIORITY ORDER: 37SOLUTION: 6.31 DTC P2135,P2138

DTC: P2176FAULT CONDITION: Throttle actuator control system - closed position not learnedPRIORITY ORDER: 50SOLUTION: 6.32 DTC P2176

DTC: U1016FAULT CONDITION: Loss of ECM Serial DataPRIORITY ORDER: 7SOLUTION: 2.3 DTC U1016,U1040,U1064,U1097,U1255

DTC: U1040FAULT CONDITION: Loss of ABS serial dataPRIORITY ORDER: 8SOLUTION: 2.3 DTC U1016,U1040,U1064,U1097,U1255

DTC: U1064FAULT CONDITION: Loss of TSM/TSSM/HFSM Serial DataPRIORITY ORDER: 6SOLUTION: 2.3 DTC U1016,U1040,U1064,U1097,U1255

DTC: U1097FAULT CONDITION: Loss of Speedometer Serial dataPRIORITY ORDER: 5SOLUTION: 2.3 DTC U1016,U1040,U1064,U1097,U1255

Page 21: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: U1255FAULT CONDITION: Missing response at modulePRIORITY ORDER: 9SOLUTION: 2.3 DTC U1016,U1040,U1064,U1097,U1255

DTC: U1300FAULT CONDITION: Serial Data LowPRIORITY ORDER: 3SOLUTION: 2.4 DTC U1300,U3101 OR BUS ERROR

DTC: U1301FAULT CONDITION: Serial Data Open/HighPRIORITY ORDER: 4SOLUTION: 2.4 DTC U1300,U3101 OR BUS ERROR

Radio Diagnostics:The radio DTCs are retrieved through the radio and displayed on the radio display.

Press eject button to remove CD from unit.While pressing and holding any two softkeys (buttons 1- 6), turn ignition switch "ON" until radio diagnostic display appears.

Radio Diagnostic Trouble Codes -RDTCs-

DTC: B0563FAULT CONDITION: Battery Voltage HighFAULT-SET CONDITION: t>=15 sec. V>= 16 VoltsFAULT-CLEAR CONDITION T=TIME; R=RESISTANCE: Normal range for t>= 15 sec

DTC: B2006FAULT CONDITION: Radio switch stuck or openFAULT-SET CONDITION: t>=15 secFAULT-CLEAR CONDITION T=TIME; R=RESISTANCE: Normal range for t>= 15 sec

DTC: B2007FAULT CONDITION: Handlebar switch shorted highFAULT-SET CONDITION: Ignition ON after Ignition OFF for at least 10 sec., t=instantaneousFAULT-CLEAR CONDITION T=TIME; R=RESISTANCE: Normal range for t>=15 sec *

DTC: B2008FAULT CONDITION: Handlebar switch shorted lowFAULT-SET CONDITION: Ignition ON after Ignition OFF for at least 10 sec., t=instantaneousFAULT-CLEAR CONDITION T=TIME; R=RESISTANCE: Normal range for t>=15 sec*

DTC: B2009FAULT CONDITION: Handlebar switch stuck or openFAULT-SET CONDITION: t>=15 secFAULT-CLEAR CONDITION T=TIME; R=RESISTANCE: Normal range for t>=15 sec

Page 22: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: B2010FAULT CONDITION: Passenger switch shorted highFAULT-SET CONDITION: Ignition ON after Ignition OFF for at least 10 sec., t=instantaneousFAULT-CLEAR CONDITION T=TIME; R=RESISTANCE: Normal range for t>=15 sec*

DTC: B2011FAULT CONDITION: Passenger switch shorted lowFAULT-SET CONDITION: Ignition ON after Ignition OFF for at least 10 sec., t=instantaneousFAULT-CLEAR CONDITION T=TIME; R=RESISTANCE: Normal range for t>=15 sec*

DTC: B2012FAULT CONDITION: Passenger switch stuck or openFAULT-SET CONDITION: t>=15 secFAULT-CLEAR CONDITION T=TIME; R=RESISTANCE: Normal range for t>=15 sec

DTC: B2016FAULT CONDITION: Front speakers shortedFAULT-SET CONDITION: R<1.5 Ohms tested once per ignition cycle R>1.0 Ohm when setup as line out ignition ON after Ignition OFF for at least 10 sec., t=instantaneousFAULT-CLEAR CONDITION T=TIME; R=RESISTANCE: R>1.5 Ohms tested once per ignition cycle

DTC: B2017FAULT CONDITION: Front speakers openFAULT-SET CONDITION: R>100 Ohms tested once per ignition cycle ignition ON after Ignition OFF for at least 10 sec., t=instantaneousFAULT-CLEAR CONDITION T=TIME; R=RESISTANCE: R>100 Ohms tested once per ignition cycle

DTC: B2018FAULT CONDITION: Front speakers shorted to groundFAULT-SET CONDITION: Ignition ON after Ignition OFF for at least 10 sec., t=instantaneous

DTC: B2019FAULT CONDITION: Front speakers shorted to batteryFAULT-SET CONDITION: Ignition ON after Ignition OFF for at least 10 sec., t=instantaneous

DTC: B2020FAULT CONDITION: Rear speakers shortedFAULT-SET CONDITION: R<1.5 Ohms tested once per ignition cycle R>1.0 Ohm when setup as line out ignition ON after Ignition OFF for at least 10 sec., t=instantaneousFAULT-CLEAR CONDITION T=TIME; R=RESISTANCE: R>1.5 Ohms tested once per ignition cycle

DTC: B2021FAULT CONDITION: Rear speakers openFAULT-SET CONDITION: R>100 Ohms tested once per ignition cycle ignition ON after Ignition OFF for at least 10 sec., t=instantaneousFAULT-CLEAR CONDITION T=TIME; R=RESISTANCE: R<100 Ohms tested once per ignition cycle

DTC: B2022FAULT CONDITION: Rear Speakers shorted to groundFAULT-SET CONDITION: Ignition ON after Ignition OFF for at least 10 sec., t=instantaneous

Page 23: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

DTC: B2023FAULT CONDITION: Rear speakers shorted to batteryFAULT-SET CONDITION: Ignition ON after Ignition OFF for at least 10 sec., t=instantaneous

* Ignition ON after Ignition OFF for at least 10 seconds.

Calibration Data:I = Intercom: 0=Disabled; 1=EnabledJ = J1850: 0=Disabled; 1=EnabledV = Vehicle Speed Input: 0=Low; 1=High (1998-2005 Only)H = Hardware Revision

ACR --> Automatic Compression ReleaseAFR --> Air Fuel RatioAIS --> Active Intake SelenoidATS --> Air Temperature SensorBAS --> Bank Angle SensorCAN --> Control Area NetworkCCA --> Cold Cranking AmpsCCM --> Cruise Control ModuleCKP --> Crank Position Sensor. The CKP generates an “AC signal” which is sent to the ECM where it is used to reference engine position (TDC) and speed. Home position established by taking readings off the 22 teeth on the alternator rotor.

DLC --> Data Link ConnectorDTC --> Diagnostic Trouble CodesECM --> Electronic Control Module. (The Computer) Computes the spark advance for proper ignition timing and fuel control based on sensor inputs (from CKP, MAP & TP sensors) and controls the low-voltage circuits for the ignition coils and injectors. The dwell time for the ignition coil is also calculated in the microprocessor and is dependent upon battery voltage. The programmed dwell feature gives adequate spark at all speeds.

ECT --> Engine Coolant Temperature. Sensor also controls the cooling fan relay that provides 12 Vdc to the fans.

ECU --> Electronics Control unitEFI --> Electronic Fuel InjectionEFP --> Electronic Fuel PumpET --> Engine Temperature sensorFI --> Fuel InjectorsFPR --> Fuel Pressure regulatorEVAP --> Evaporative Emissions Control SystemFPS --> Fuel Pressure SensorHCU --> Hydraulic Control UnitH-DSSS --> Harley-Davidson Smart Security SystemHFSM --> Hands-free Security ModuleIAC --> Idle Air Control actuatorIAT --> Intake Air Temperature sensorIC --> Instrument ClusterISS --> Ion Sensing System…detonation detectionJSS --> Jiffy Stand SensorMAP --> manifold Absolute Pressure sensor. The MAP sensor monitors the intake manifold pressure (vacuum) and sends the information to the ECM. The EMC then adjusts the spark and fuel-timing advance curves for optimum performance.

Page 24: CÓDIGOS DE ERROS DE 2010 EM DIANTE - nacao.digital · See Table 2. Turn Ignition switch to OFF & Run/Stop switch is to Run. Push odometer reset button in & hold. Turn ignition switch

WWW.MALUCOSPORCUSTOM.COM.BR | BLOG.MALUCOSPORCUSTOM.COM

CÓDIGOS DE ERROS DE2010 EM DIANTE

RCM --> Reverse Control ModuleTCA --> Throttle Control ActuatorTGS --> Twist Grip SensorTMAP --> Intake air temperature/manifold absolute pressure

TPS --> Throttle Position SensorTSM/TSSM --> (Turn Signal/ Turn Signal Security Module)

VE --> Volume EfficiencyVSS --> Vehicle Speed Sensor. Used as an input for idle speed control

WSS --> Wheel Speed Sensor