Cobra ODE Setup Manual on PS3 FAT PATA

Cobra ODE Setup Manual on PS3 FAT PATA

Preamble :The Cobra ODE is the only smart to have broad compatibility with all models of PS3. Its simple installation and the quality of these components make the best flea market for the PS3. All models PS3 are compatible, the first FAT Čecha to the latest PS3 Super Slim. (Only CECHL models with or near the BMD-021 controller(photos   available   here) remains inviolable whatever the chip, the Team Cobra is still work to be clarified that an update to the compatibility of these consoles.)

Reminder of the main features of the Cobra ODE:- Reading of ISO PlayStation 3 from a USB external hard drive - Automatic update of the console via authorized Internet - Connecting to safely PSN - Play DVD ISO and Blu-Ray (Film, etc.) - Launch of a kind software Homebrew and much more ...

Installing the Cobra ODE on your console

This guide is brought to you for PlayStation 3 FAT pata model, serial number: Čecha, CECHB, CECHC, CECHE, CECHG, CECHK

Preparation of materials: The main PCB Cobra ODE:

Skip switch circled in red on the PATA mode (switch on the other side of the card is not used in this mode)

From version 4.20 of Cobra ODE switches are gone, the Cobra ODE automatically detects the mode to use

USB PCB Cobra ODE:

The power cable corresponds to that of your console (3.4 or 5 pins)

Choose the same connector as the original model of your console

The fixing clips Type B:

3 will be used only

The double-sided adhesive Cobra ODE:

CTFs tablecloths for your version of Cobra ODE:Your Cobra ODE is version 3.00:

Cobra connection between ODE and PS3 motherboard: Tablecloth "broad" 60 320mm pine same side connector

Cobra connection between ODE and the Blu-ray player: Tablecloth "broad" 60 pines connector 320mm opposite side

Cobra connection between ODE and USB PCB Cobra ODE: Tablecloth 24 pin connector same side of 370mm

Your Cobra ODE is a version of 4.20 or greater:

Cobra connection between ODE and PS3 motherboard: Tablecloth "broad" 60 220mm pine same side connector

Cobra connection between ODE and the Blu-ray player: Tablecloth "broad" 60 270mm pine same side connector

Cobra connection between ODE and USB PCB Cobra ODE: Tablecloth 24 pin connector same side of 370mm

Removing the FAT PS3 Console:

Just follow the images below to show you where are the screws to remove the top shell: Once this is done you have access to the player and to the power of the console. You have to remove the drive (WARNING PATCHES OF THE CLIP):

Fixing clips tablecloths that are fragile and raise!

Remove the console power cable (ATTENTION, the power connectors on motherboards PS3 FAT become very fragile over time, remove it gently with small swings):

Pose Cobra ODEYou then need to install new sheets depending on the version of your Cobra ODE: Your Cobra ODE is version 3.00: Connection between Cobra ODE PATA MB connector and PS3 motherboard: Tablecloth "broad" 60 pine 320mm same side connector connection between the Cobra ODE PATA connector DRV and Blu-Ray:Tablecloth "broad" 60 pines connector 320mm side opposite connection between the Cobra ODE UIF connector and USB PCB Cobra ODE: Tablecloth

24 pin connector same side of 370mm

Your Cobra ODE is 4.20 or higher Version:Connection between Cobra ODE PATA MB connector and PS3 motherboard: Tablecloth "broad" 60 pine 220mm same side connector connection between the Cobra ODE connector PATA DRV and Blu-Ray:Tablecloth "broad" 60 270mm pine same side connector connection between the Cobra ODE UIF connector and USB PCB Cobra ODE: 24 pine 370mm table along side connector

You can then paste the double-sided sticker Cobra ODE on the player and ask the main PCB top

Connect the new power cable supplied with the Cobra ODE like this: Ask the USB PCB at the rear of the console with the type B clip: You can now organize the sheets neatly in your console so that celle- it does not bother reassembly.

http://www.pucesconsoles.com/wp-content/blogs.dir/12/files/2014/01/Branchement-Alimentation-Cobra-ODE.jpg

It'll just wind your PS3 console, making sure the cables and you're done!Consult the User's Guide (coming soon) to learn how to use your Cobra ODE