CNC Waterjet Machine DWJ1525-FC With DIPS6 2230 · It can start cutting from the same block where...

of 4

1. Cutting table

- DWJ1525-FC CNC X-Y cutting table

- Structure: Flying arm

- Travel of X axis: 1500mm

- Travel of Y axis: 2500mm

- Travel of Z axis: 210 mm

- Ball screw& LM Guide way System

- NC system- : Washing 101/102

� Large Program can run directly from USB Pen Drive.

� Certain Programs can also be stored on NC System by USB

Pen Drive.

� Graphic Display of the Cutting Profile

� Retrace of Cut Path is possible

� Panel, Control Unit & Keypad is IP65 Protected.

� Typical NC Interface on Board with RS2 32 & USB Slot.

� Hand wheel as an option.

� Global customer Network Support.

- In case of Power Failure, Machine need not run complete program file

again. It can start cutting from the same block where the Power Failure

occurred by creating a new NC Program.

- Motion System : Servo Drive, Delta

- Traverse Speed : 15 m/min max

- Contour Speed : 2 m/min

- Linear Positioning Accuracy : ± 0.05 mm

- Linear Positioning Repeatability : ± 0.05 mm

# 3-182T, Vinayaga Tower Kadampadi Road, Above SBI Bank- AFS Sulur, Coimbatore, India PIN – 641401

Ph: 9952923400 ;0422-2684656 Email : [email protected]

Website: www.rpmtools.in

DWJ1525-FC With DIPS6 2230

CNC Waterjet Machine

of 4

(1) Grid for Metal (2) Grid for Glass

• CAM Software (1 set)

i. Auto- transforming AutoCAD files into G Codes and M Codes.

ii. The Nesting Module supports Auto and Manual Nesting with option

of Move, Rotate, Mirror, Array operations with multi part selection

facility.

iii. This software has feature of Sharp Angle slow down to generate

perfect profile

iv. The CAD Module supports the definition of process data including

Lead-In, Lead-Out, Marker, drill, cut-style, stitch, corner loop etc.

v. The CAD Module has library of various Shapes

vi. Open database can save the cutting parameters of different

materials. Without inputting the parameters again, you can use

them in your CNC programs only by a mouse click.

vii. The CAM Module generates detailed statistic report like material

grade, thickness, length of cut, number of piercing points, part

name if specified etc in user defined row and as per the unit

specified by the user.

- Maximum Load Capacity: 1000 kg/m2 or Higher Load Capacity as per

request.

- Power supply: 380~415V AC, 50Hz, 3 Phase (Standard) (or) as per your

Purchase Order

- Motorized Z axis




of 4

2. HIGH PRESSURE PUMP

DIPS6-2230 High Pressure

- Far Higher Efficiency

- Very Low Operating Cost

- Smooth and Consistent pressure at the Nozzle

- Easy to carry out maintenance

- Max. Operating pressure: 40000 psi (300mpa)

- Pressure Intensification ratio: 24:1

- Max. Flow rate: 3.1 lpm

- Inlet water pressure: 0.4 mpa (For Intensifier)

- Triple cartridge inlet water filtration to 0.5 micron with inlet and outlet pressure

gauges.

- Pressure control valve.

- Pump is mounted on its own skid for vibration isolation and easy service.

- Main motor power: 22kw / 30HP

- Voltage: 415 VAC, 50Hz, 3 Phase (Standard) or as per your Purchase Order

- Inlet Water pressure for heat exchanger :0.8 mpa

- Oil Recycling: 52 liters/min.

- Intensifier completely made by Dardi Water Cutter Co. Ltd. China.

- Integral Inlet water filters (5Micron, 1micron, 0.45micron in series)

- Working hour counter

- Special tool kit for maintenance / repair

- Arbitrarily hands adjusting working pressure

- Automatically shut down (Trip Off) in case of super pressure of oil or low

pressure of water for protection.

- Dimensions:(Approximately)

• Length – 1670mm

• Width - 920mm

• Height – 1180mm




of 4




3. DWCH ON/OFFValve (1 set)

- Pneumatic pressure driven valve to release and

stop the high pressure water going into the cutting

head. This valve is automatically controlled as per

the program given to the CNC Controller.

4. DSP7 Abrasive cutting head (1 set)

- Cutting Head includes 3 main parts namely:

Orifice, Mixing Chamber and Focusing Tube (Nozzle)

Which are made from extremely wear

Materials.

- Pure Water cuts can be made with the same orifice

so that re-tooling takes only a few seconds.

- Mini Hopper Abrasive supply System

5.DCAS-B Abrasive controlling valve system (1 set)

- It is mounted directly on to the motion system.

Thus, the abrasive hose transfer the abrasive to

the cutting head quickly, w

as long hose length results in poor cut quality.

- Specific Abrasive Control & variables required

during cutting is maintained.

- The consistent regulated feed

reduces wastage of abrasive & gives in a perfect

cutting jet to give smoother cutting edge on the

workpiece.

- It is easy to use & monitor the maximum abrasive flow

rate for the better performance during cutting.

- No special tools required for day to day maintenance.

DWCH ON/OFFValve (1 set)

Pneumatic pressure driven valve to release and

stop the high pressure water going into the cutting

head. This valve is automatically controlled as per

the program given to the CNC Controller.

Abrasive cutting head (1 set)

Cutting Head includes 3 main parts namely:

Orifice, Mixing Chamber and Focusing Tube (Nozzle)

Which are made from extremely wear-resistance

Pure Water cuts can be made with the same orifice

g takes only a few seconds.

Mini Hopper Abrasive supply System

B Abrasive controlling valve system (1 set)

It is mounted directly on to the motion system.

Thus, the abrasive hose transfer the abrasive to

the cutting head quickly, which is an advantage,

as long hose length results in poor cut quality.

Specific Abrasive Control & variables required

during cutting is maintained.

The consistent regulated feed-rate of abrasive

reduces wastage of abrasive & gives in a perfect

cutting jet to give smoother cutting edge on the

It is easy to use & monitor the maximum abrasive flow

rate for the better performance during cutting.

No special tools required for day to day maintenance.

CNC Waterjet Machine DWJ1525-FC With DIPS6 2230 · It can start cutting from the same block where...

Documents

Transcript of CNC Waterjet Machine DWJ1525-FC With DIPS6 2230 · It can start cutting from the same block where...