Cli Xpand Ip

7/25/2019 Cli Xpand Ip

1/31

XPAND-IP

CLI

(Command Line Interface)

User Guide

For R3A software series


2/31

Table of contents:

INTRODUCTION........................................................................................................................................ 6

ACCESSING THE ELEMENT .................................................................................................................. 6

VALID USERS ............................................................................................................................................. 6GETTING STARTED.................................................................................................................................. 7

GETTING HELP ......................................................................................................................................... 9

MODES ......................................................................................................................................................... 9

CHANGING MODES.................................................................................................................................. 9

NON PRIVILEGED USERS..................................................................................................................... 10

CLI COMMANDS...................................................................................................................................... 11

MODE:USEREXEC................................................................................................................................. 11clear screen......................................................................................................................................... 11exit....................................................................................................................................................... 11help ..................................................................................................................................................... 11logout.................................................................................................................................................. 11

MODE:EXEC........................................................................................................................................... 12clear screen......................................................................................................................................... 12configure terminal............................................................................................................................... 12end....................................................................................................................................................... 12exit....................................................................................................................................................... 12help ..................................................................................................................................................... 12logout.................................................................................................................................................. 12reset..................................................................................................................................................... 12save-config.......................................................................................................................................... 12setelementip ........................................................................................................................................ 12show history ........................................................................................................................................ 12

show running-config ........................................................................................................................... 12clear counters ..................................................................................................................................... 14clear spanning-tree detected protocols............................................................................................... 14show [provider-bridge] port config.................................................................................................... 14show customer spanning-tree.............................................................................................................. 14show flow-control................................................................................................................................ 14show interface bridge port-type .......................................................................................................... 14show interface mtu .............................................................................................................................. 14show interfaces [{ ] counters......................................................... 14show dot1d mac-address-table............................................................................................................ 14show interfaces ................................................................................................................................... 15show lldp............................................................................................................................................. 15show lldp errors .................................................................................................................................. 15

show lldp interface.............................................................................................................................. 15show lldp local.................................................................................................................................... 15show lldp neighbors ............................................................................................................................ 15show lldp statistics .............................................................................................................................. 15show lldp traffic .................................................................................................................................. 16show mac-address-table...................................................................................................................... 16show mac-address-table aging-time ................................................................................................... 16show rmon........................................................................................................................................... 16show users........................................................................................................................................... 16show vlan ............................................................................................................................................ 16


3/31

show vlan device info.......................................................................................................................... 16show vlan port config.......................................................................................................................... 16

EXAMPLES OF EXEC MODE COMMANDS....................................................................................... 17

show running-config ........................................................................................................................... 17show spanning-tree............................................................................................................................. 17show spanning-tree bridge.................................................................................................................. 17

show spanning-tree interface.............................................................................................................. 17show spanning-tree detail................................................................................................................... 18show spanning-tree root ..................................................................................................................... 18

MODE:CONFIGURE .............................................................................................................................. 19clear screen......................................................................................................................................... 19end....................................................................................................................................................... 19exit....................................................................................................................................................... 19help ..................................................................................................................................................... 19interface .............................................................................................................................................. 19no spanning-tree ................................................................................................................................. 19no spanning-tree priority ................................................................................................................... 19no spanning-tree compatibility ........................................................................................................... 19no spanning-tree pathcost dynamic .................................................................................................... 19no spanning-tree transmit hold-count................................................................................................. 19no spanning-tree forward-time ........................................................................................................... 19no spanning-tree hello-time ................................................................................................................ 19no spanning-tree max-age................................................................................................................... 19shutdown spanning-tree ...................................................................................................................... 19spanning-tree ...................................................................................................................................... 20spanning-tree priority ......................................................................................................................... 20spanning-tree compatibility ................................................................................................................ 20spanning-tree mode............................................................................................................................. 20spanning-tree pathcost dynamic ......................................................................................................... 20spanning-tree transmit hold-count...................................................................................................... 20spanning-tree forward-time ................................................................................................................ 20spanning-tree hello-time ..................................................................................................................... 20

spanning-tree max-age........................................................................................................................ 20bridge-mode........................................................................................................................................ 21clear lldp counters .............................................................................................................................. 21clear lldp table.................................................................................................................................... 21clear spanning-tree counters .............................................................................................................. 21ether-type ............................................................................................................................................ 21mac-address-table aging-time............................................................................................................. 21no mac-address-table aging-time........................................................................................................ 21spanning-tree provider........................................................................................................................ 21no spanning-tree provider................................................................................................................... 21vlan ..................................................................................................................................................... 21no vlan ................................................................................................................................................ 21set cli pagination................................................................................................................................. 21

EXAMPLES OF CONFIGURE MODE COMMANDS. ........................................................................ 22

spanning-tree forward-time ................................................................................................................ 22no spanning-tree forward-time ........................................................................................................... 22

MODE:INTERFACE ............................................................................................................................... 23clear screen......................................................................................................................................... 23end....................................................................................................................................................... 23exit....................................................................................................................................................... 23help ..................................................................................................................................................... 23no shutdown ........................................................................................................................................ 23


4/31

no spanning-tree pseudoRootId .......................................................................................................... 23no spanning-tree auto-edge ................................................................................................................ 23no spanning-tree layer2-gateway-port................................................................................................ 23no spanning-tree restricted-role ......................................................................................................... 23no spanning-tree restricted-tcn ........................................................................................................... 23no spanning-tree cost.......................................................................................................................... 23no spanning-tree disabled................................................................................................................... 23no spanning-tree link-type .................................................................................................................. 23no spanning-tree portfast .................................................................................................................... 23no spanning-tree port-priority ............................................................................................................ 23shutdown............................................................................................................................................. 24spanning-tree ...................................................................................................................................... 24spanning-tree auto-edge ..................................................................................................................... 24spanning-tree bpdu-receive................................................................................................................. 24spanning-tree bpdu-transmit............................................................................................................... 24spanning-tree layer2-gateway-port..................................................................................................... 24spanning-tree restricted-role .............................................................................................................. 24spanning-tree restricted-tcn................................................................................................................ 24spanning-tree cost............................................................................................................................... 24spanning-tree disable.......................................................................................................................... 24duplex.................................................................................................................................................. 25flowcontrol .......... ........... .......... ........... .......... ........... .......... ........... .......... ........... .......... ........... .......... .. 25l2protocol-discard............................................................................................................................... 25l2protocol-peer ................................................................................................................................... 25l2protocol-tunnel................................................................................................................................. 25lldp notification................................................................................................................................... 25lldp tlv-select basic-tlv ........................................................................................................................ 25lldp tlv-select dot1tlv........................................................................................................................... 26lldp tlv-select dot3tlv........................................................................................................................... 26lldp ...................................................................................................................................................... 26negotiation .......................................................................................................................................... 26no duplex............................................................................................................................................. 26no l2protocol-tunnel............................................................................................................................ 26

no lldp notification.............................................................................................................................. 26no lldp tlv-select basic-tlv ................................................................................................................... 26no lldp tlv-select dot1tlv...................................................................................................................... 27no lldp tlv-select dot3tlv...................................................................................................................... 27no lldp ................................................................................................................................................. 27no negotiation ..................................................................................................................................... 27no spanning-tree bpdufilter................................................................................................................. 27no spanning-tree loop-guard .............................................................................................................. 27no speed .............................................................................................................................................. 27no switchport....................................................................................................................................... 27no switchport acceptable frame-type .................................................................................................. 27no switchport pvid............................................................................................................................... 27set-bridge port-type............................................................................................................................. 27

spanning-tree bpdufilter...................................................................................................................... 28spanning-tree loop-guard ................................................................................................................... 28no lldp ................................................................................................................................................. 28no negotiation ..................................................................................................................................... 28no spanning-tree bpdufilter................................................................................................................. 28no spanning-tree loop-guard .............................................................................................................. 28spanning-tree pseudoRootId priority .................................................................................................. 28speed ................................................................................................................................................... 28switchport............................................................................................................................................ 28switchport acceptable-frame-type....................................................................................................... 28


5/31

switchport pvid.................................................................................................................................... 28spanning-tree link-type ....................................................................................................................... 28spanning-tree portfast......................................................................................................................... 28spanning-tree port-priority ................................................................................................................. 28

EXAMPLES OF INTERFACE MODE COMMANDS. ......................................................................... 29

spanning-tree restricted-tcn................................................................................................................ 29spanning-tree pseudoRootId............................................................................................................... 29

MODE:VLAN_CONFIG ......................................................................................................................... 30no ports ............................................................................................................................................... 30ports .......... .......... ........... .......... ........... .......... ........... .......... ........... .......... ........... .......... ........... .......... .. 30vlan active........................................................................................................................................... 30

EXAMPLES OF VLAN MODE COMMANDS. ..................................................................................... 31


6/31

Introduction

This guide explains how to use the command line interface (CLI) for XPAND-IP andcontains the list of commands with explanations of each command.

The user guide is for a specific software version, as availability of commands will dependon the functionality of particular software release.

The valid software version for this user guide is printed on the first page.

The active software version of the element can be found by using the web interface on the

element and choosing the Configuration menu item, then the Software menu item.

The web page that appears will show the active software version on the element.

Accessing the element

Access to the XPAND-IP element requires a telnet session with the element; this may be

achieved by using a DOS box in Windows XP and using the command telnet with the ip

address of the element as a parameter. Other operating systems may have othercommands to achieve the same result though.

Valid users

All users of the CLI must be users contained in the elements user database. When a user

tries to log in via the CLI the user is checked by the elements security system. Userparameters like access rights and auto logout time will affect the commands available to

the user and the acceptable inactivity time before logout.

There are only two access rights in the CLI non-privileged or privileged users.

Element security levels of Active, Master or Admin correspond to privileged users of the

CLI all other element security levels correspond to un-privileged users with limited

abilities.


7/31

Getting started

The following description is for a Windows XP pc, if you are using another operating

system the general method should be the same but the details may differ.

First check connectivity to make sure your pc and element can talk to each other.

Open a Dos box and issue the command ping See figure 1.

Figure 1


8/31

Issue the command telnet and press [ENTER]

The result should be as shown in figure 2.

Figure 2

You are now talking with the CLI at the login screen, type a valid user name and

press [ENTER], then the users password and press [ENTER].

A screen similar to that of figure 3 should appear.

Figure 3

Congratulations you have successfully logged in to the CLI.

The prompt on the left-hand side of the blinking cursor is context or modedependant and also indicates if you are a privileged user or not, a privileged user

is indicated by a # and a non-privileged user is indicated by a >.


9/31

GettingHelp

At any time you may type the command help to list all commands available with theirparameter list. Typing a command and then help on the same line will give more detailed

help for that particular command. Typing the first few letters of a command and pressing

[TAB] will produce a list of commands beginning with that letter combination.

Modes

A mode is a subset of all commands available.When you are in a mode the prompt will indicate the mode you are currently in.

Modes available

Mode name Prompt

assuming privileged

user

Main purpose

EXEC # Show commands

CONFIGURE (config)# Configuring parameters

VLAN (config-vlan)# Configuring vlan ports

INTERFACE (config-if)# Configuring parameters for a particular

interface

When you first log in you will be in EXEC mode, typing help at the prompt will list all

commands available in this mode.

Changingmodes

To enter CONFIGURE mode you will need to use the command configure terminal,notice how the prompt changed from a # to (config)#. To enter INTERFACE mode

you must first be in CONFIGURE mode, the command to enter INTERFACE mode

requires two parameters, the interface-type and interface-id.

Example: interface gigabitethernet 0/1

Hint: Try to enter only the first few characters of each word then press tab

Like this:

in [TAB] gi [TAB] 0/1 notice how the tab expansion works.

When you have entered the INTERFACE mode the prompt will have changed to

(config-if)#

To move back to the previous mode use the exit command, to get back to EXEC mode

directly use the end command.


10/31

Non privileged users

Non privileged users only have access to a mode called USEREXEC, in this mode nocommands of value can be executed.

Mode available for non privileged users

Mode name Prompt Main purpose

USEREXEC > None


11/31

CLI Commands

Mode: USEREXEC

Command Parameter list Description

clear screen

Clears the screen

exitGo back to previous modeor log out from CLI

help[ command ] List commands or get more

help on a command

logoutLog out from CLI


12/31

Mode: EXEC


clear screenClears the screen

configure terminal

Enters configuration mode

endExit from Configure mode

exitGo back to previous modeor log out from CLI

help[command] List commands or get more

help on a command

logoutLog out from CLI

resetRestarts the element

save-configPermanently saves thecurrent config

setelementip[ip-address subnetMask

gateway]

Set the ip address

show historyShows a history of

commands executed in this

CLI session

show running-config[{stp | vlan [ ] | rmon}]

The parameters above allowyou to only choose aspecific sub section

Shows the configurationcurrently running

show spanning-tree [{ summary | blockedports |

pathcost method }]

Shows the summary,

blocked portsor pathcost

method

Displays spanning tree

information

show spanning-tree active [detail]

When detailis added moredetaild information is

shown

spanning tree information

of active ports

show spanning-tree bridge [{ address | forward-time |

hello-time | id |max-age |

protocol | priority | detail }]

Displays the spanning-tree

configuration of the bridge


13/31

Mode: EXEC continuedCommand Parameter list Description

show spanning-tree detail Displays detailed spanning

tree information

show spanning-treeinterface

[{ cost | priority |portfast | rootcost |

restricted-role | restricted-

tcn | state | stats | detail }][

] layer2-

gateway-port

cost port cost

priority port priority

portfast enabled /disabled

rootcost root cost

restricted-role enabled/disabled

restricted-tcn enabled /

disabled

state example Forwarding

stats port statistics

detail detailed port

information

Displays Spanning-tree portconfiguration

Note this command is

displayed as two commandswhen using the help

command to list all

commands

show spanning-tree root root [{ address | cost |

forward-time | id | max-age |

port | priority | detail }]

address- root bridge

address

cost root cost

forward-time forward

time delay

id root bridge id

max-age root max ageport root port

priority root priority

detail root details

Displays spanning tree root

information


14/31


clear counters[

]

Clears the interface

counters

clear spanning-tree detectedprotocols

[{interface

}]

Restarts the protocol

migration process on

the specified interface

Restart the protocol

migration process

show [provider-bridge] port

config

[{port }]

Portrelated configuration

Displays port information

show customer spanning-

tree

[cep interface ]

[{ detail [active] | active[detail] }]cep: Customer Edge Port

active: Displays the Bridgeand details of the active

detail: Displays in detail

about the port and bridge

Displays detailed customer

spanning tree information

show flow-control[ interface

]

Displays flow-control

information

show interface bridge port-type

[

]

Shows the Bridge Port Type

of interfaces in the switch

show interface mtuShows the MaximumTransmission Unit (MTU)

of interfaces in the switch

show interfaces [{ ] counters

Counters for all the

available interfaces

show dot1d mac-address-

table

[address]

[{interface }]

Displays Unicast andMulticast Mac Address

table


15/31


show interfaces[{ [

] [{

description | flowcontrol |

capabilities | status }] }]

capabilities:Capabilities of the interface

flowcontrol:

Receive or send flow

control value for aninterface

description:

Description about theinterface

Displays interface status

and configuration

show lldp Displays LLDP globalconfiguration details

show lldp errorsDisplays the information

about the errors like

memory allocation failures,queue overflows, table

overflows, etc

show lldp interface[

]

Displays LLDP

configuration details on aparticular interface or all

interfaces

show lldp local{[

] | [mgmt-

addr]}

Displays the current switch

information that will be

used to populate outboundLLDP advertisements for a

specific interface or all

interfaces

show lldp neighbors[chassis-id

port-id ][

][detail]

Displays information about

neighbors learnt on aninterface or all interfaces

show lldp statistics Displays the LLDP remotetable statistics

information


16/31


show lldp traffic[ ] Displays LLDP counters,

including the no. of frames

sent, received, discarded,etc

show mac-address-table[vlan ]

[address

][{interface

}]

Displays Unicast and

Multicast Mac Address

table

show mac-address-tableaging-time

Displays the Aging Time

for the Mac Address Table

entries

show rmon

[statistics []] [alarms] [events][history [history-index (1-

65535)] [overview]]

alarmsConfigured alarm details

eventsConfigured event details

historyConfigured history details

statistics

Statistics relatedinformation

Display RMON

show usersDisplay information aboutterminal lines

show vlan[brief | id |

summary]

Displays VLAN global

status for the

specified VLAN range

(ex.1-4)

show vlan device info

Displays VLAN global

status variables

show vlan port config[{port

}]

Displays Port information


17/31

Examples of EXEC mode commands.

show running-config

# show running-config stp

Building configuration...spanning-tree pathcost dynamicinterface gigabitethernet 0/1spanning-tree link-type point-to-point

show spanning-tree

# show spanning-tree

We are the root of the Spanning TreeRoot Id Priority 32768

Address 00:60:c0:20:08:70

Cost 0Max Age 20 Sec, Forward Delay 15 Sec

Spanning tree Protocol Enabled.

Bridge is executing the rstp compatible Spanning Tree ProtocolBridge Id Priority 32768

Address 00:60:c0:20:08:70Hello Time 2 sec, Max Age 20 sec, Forward Delay 15 secDynamic Path Cost is Enabled

Name Role State Cost Prio Type---- ---- ----- ---- ---- ------Gi0/1 Designated Forwarding 200000 128 P2P

show spanning-tree bridge

# show spanning-tree bridge

Bridge ID HelloTime MaxAge FwdDly Protocol--------- --------- ------ ------ --------80:00:00:60:c0:20:08:70 2 20 15 rstp

show spanning-tree interface

# show spanning-tree interface gigabitethernet 0/1

Role State Cost Prio Type---- ----- ---- ---- ----Designated Forwarding 200000 128 P2P


18/31

show spanning-tree detail

# show spanning-tree detail

Spanning tree Protocol Enabled.

Bridge is executing the rstp compatible Spanning Tree Protocol

Bridge Identifier has priority 32768, Address 00:60:c0:20:08:70Configured Hello time 2 sec, Max Age 20 sec, Forward Delay 15 secDynamic Path Cost EnabledWe are the root of the spanning treeNumber of Topology Changes 0Time since topology Change 0 seconds agoTransmit Hold-Count 3Max Age 20 Sec, Forward Delay 15 SecHello Time 2 Sec

Port 1 [Gi0/1] is Designated, ForwardingPort PathCost 200000, Port

Priority 128, Port Identifier 128.1Designated Root has priority 32768, address 00:60:c0:20:08:70Designated Bridge has priority 32768, address 00:60:c0:20:08:70

Designated Port Id is 128.1, Designated PathCost 0No of Transitions to forwarding State :1PortFast is enabledLinkType is point to PointBPDUs : sent 355 , recieved 0Timers: Hello - 1, Forward Delay - 0, Topology Change - 0Restricted Role is disabled.Restricted TCN is disabled.bpdu-transmit enabledbpdu-receive enabled

show spanning-tree root

# show spanning-tree root

Root ID RootCost MaxAge FwdDly RootPort------- --------------- ------ --------80:00:00:60:c0:20:08:70 0 20 15


19/31

Mode: CONFIGURE



end

Exit from Configure mode

exitGo back to previous mode

or log out from CLI


help on a command

interface{

}

Enter interface

configuration mode

no spanning-treeshuts down spanning tree

operation

no spanning-tree priority

no spanning-tree

compatibility

Sets the compatibilityversion for spanning tree

protocol to its default value

no spanning-tree pathcostdynamic

[lag-speed] No dynamic path cost

calculations are done

no spanning-tree transmit

hold-count

Sets the transmit hold-countto its default value

no spanning-tree forward-time

forward-time 15 secs

no spanning-tree hello-timehello-time 2 secs

no spanning-tree max-agemax-age 20 secs

shutdown spanning-treeShutdown spanning tree

operation


20/31

Mode: CONFIGURE continuedCommand Parameter list Description

spanning-treeStart spanning tree

operation

spanning-tree priority

Set priority

spanning-tree compatibility{stp | rst} Set compatibility mode

spanning-tree moderst Set mode

spanning-tree pathcostdynamic

[lag-speed] The pathcost of all the ports

will be calculated

dynamically based on thespeed of the interface.

If the cost has already been

configured an rstp interface,

then this command has noeffect on those interfaces

spanning-tree transmit hold-

count

Sets the transmit hold count

spanning-tree forward-time Controls how fast a port

changes its spanning treestate from Blocking state to

Forwarding state

spanning-tree hello-time Determines how often the

switch broadcasts its hello

message to other switcheswhen it is the root of the

spanning tree

spanning-tree max-age The maximum age allowed

for the Spanning Tree

Protocol informationlearned from the network on

any port before it is

discarded


21/31

Mode: CONFIGURE continuedCommand Parameter list Description

bridge-mode{ vlan-unaware | customer |

provider }

Set switch mode

clear lldp counters

Clears LLDP transmit and

receive statistics

clear lldp tableClears LLDP neighbors

information

clear spanning-tree countersReset all bridge and portlevel statistics counters

ether-type{ 0x88a8 | 0x9100 | 0x9200

}

Set the TPID

mac-address-table aging-

time

Sets the mac aging time in

seconds

no mac-address-table aging-time

Set mac aging time to 300(default)

spanning-tree providerEnables spanning tree

operation

no spanning-tree providerdisables spanning treeoperation

vlan Create a vlan with id and

enter VLAN_CONFIG

mode

no vlan Remove vlan with id

set cli pagination{on | off} Pause before scrolling text

off top of terminal


22/31

Examples of CONFIGURE mode commands.

When you have issued the configuration commands in CONFIGURE mode they will takeeffect immediately, but to save the changes between resets of the element you will have

to go back to EXEC mode and give the command save-config.

spanning-tree forward-time

(config)# spanning-tree forward-time 17

no spanning-tree forward-time

(config)# no spanning-tree forward-time


23/31

Mode: INTERFACE



end

Exit from Configure mode

exitGo back to previous mode

or log out from CLI


help on a command

no shutdown

no spanning-treepseudoRootId

[priority mac-

address ]

priority priority of

pseudo root

mac-address macaddressid of pseudo root

Set the pseudo root id mac-

address and priority

no spanning-tree auto-edgeDisables automaticdetection of bridge attached

on an interface

no spanning-tree layer2-gateway-port

withdraws layer two

gateway port status

no spanning-tree restricted-

role

Disables the root-guard /

restricted role feature on theport

no spanning-tree restricted-tcn

Disables the topology

change guard/ restricted

TCN feature on the port

no spanning-tree costSet cost 200000

no spanning-tree disabledEnables the spanning tree

on the port

no spanning-tree link-typeSet link type Auto

no spanning-tree portfastNot in portfast

no spanning-tree port-

priority

Set port priority to 128


24/31

Mode: INTERFACE continuedCommand Parameter list Description

shutdown

Shutdown interface

spanning-tree

spanning-tree auto-edgeThe spanning-tree auto-

edge command enables

automatic detection ofbridge attached on an

interface

spanning-tree bpdu-receive{enabled | disabled}

enabled - Receives the

BPDUs on the portdisabled - Ignores the

BPDUs received on the port

Configures the BPDU

receive status of the port

spanning-tree bpdu-transmit{enabled | disabled}

enabled - The port

transmits BPDUs

disabled - The port does

not transmit BPDUs

Configures BPDU transmitstatus of the port

spanning-tree layer2-

gateway-port

Configures port as layer twogateway port

spanning-tree restricted-roleEnables the root-guard /

restricted role feature

(prevents the specific port

from becomingthe rootport) on the port

spanning-tree restricted-tcnEnables the topology

change guard / restricted

TCN feature (prevents the

Topology change caused bythat port ) on the port

spanning-tree costcost The pathcost value

associated with the port

spanning-tree disableDisables the spanning tree

on the port


25/31


duplex{ full | half } Set port to half or full

duplex

flowcontrol

{ on | off } off

Turns off attached devicesor local ports

ability to send packets

onAllows an interface to send

or receive packets

l2protocol-discard{dot1x | lacp | stp | gvrp |

gmrp | mvrp | mmrp}

Protocol to discard

Discard packets of a

specific protocol

l2protocol-peer {stp} Peer packets of a specificprotocol

l2protocol-tunnel{dot1x | lacp | stp | gvrp |

gmrp| igmp | mvrp | mmrp}

Protocol to tunnel

Tunnel packets of a specific

protocol

lldp notification[remote-table-chg]

Trap notification for change

in neighbor table

Enables LLDP trap

notification on an interface

lldp tlv-select basic-tlv

{ [port-descr] [sys-name]

[sys-descr] [sys-capab][mgmt-addr {all | ipv4

}]}

port-descrPort description TLV

sys-nameSystem name TLV

sys-descrSystem description TLV

sys-capab

System capabilities TLVmgmt-addr

Configures transmission ofmanagment

Enables the basic TLV

transmission on a given port


26/31


lldp tlv-select dot1tlv{[port-vlan-id] [protocol-

vlan-id {all |}]

[vlan-name {all | }]}port-vlan-idPort VLAN identifier TLV

protocol-vlan-idProtocol VLAN identifier

TLV

vlan-nameVLAN name TLV

Configure dot1 TLV types

on a port

lldp tlv-select dot3tlv{ [macphy-config] [max-

framesize] }

macphy-config

MAC or PHY TLVmax-framesizeMaximum frame size TLV


on a port

lldp{transmit | receive} Enables reception and

transmission of LLDPDU

negotiationEnables auto-negotiation on

the interface

no duplexConfigures the duplexoperation to the default

value

no l2protocol-tunnel

{dot1x | lacp | stp | gvrp |

gmrp| igmp | mvrp | mmrp}

Do not tunnel packets of a

specific protocol

no lldp notificationDisables LLDP trap

notification on an interface

no lldp tlv-select basic-tlv{ [port-descr] [sys-name]

[sys-descr] [sys-capab][mgmt-addr {all | ipv4

}]}

port-descrPort description TLV

sys-name

System name TLV

sys-descrSystem description TLV

sys-capabSystem capabilities TLV

mgmt-addr

Configures transmission of

managment

Disables the basic TLV

transmission on a given port


27/31


no lldp tlv-select dot1tlv{[port-vlan-id] [protocol-

vlan-id {all |}]

[vlan-name {all | }]}port-vlan-idPort VLAN identifier TLV

protocol-vlan-idProtocol VLAN identifier

TLV

vlan-nameVLAN name TLV


on a port

no lldp tlv-select dot3tlv{ [macphy-config] [max-

framesize] }

macphy-config

MAC or PHY TLVmax-framesizeMaximum frame size TLV


on a port

no lldp{transmit | receive} Enables reception and


no negotiationDisables auto-negotiation

on the interface

no spanning-tree bpdufilterDisables BPDU filter on theinterface

no spanning-tree loop-guardDisables loop guard/

restricted forwarding on an

interface

no speedSets the speed of the

interface to its default value

no switchportTo set the interface to the

routed-interface status andto erase all layer 2

configurations

no switchport acceptableframe-type

Sets acceptable frame type

on port to default value

no switchport pvid

Sets PVID for the port to

default value

set-bridge port-type{ providerNetworkPort |

customerNetworkPort }

Set port type to customer or

provider


28/31


spanning-tree bpdufilter{disable | enable} Disables or enables BPDU

filtering

spanning-tree loop-guard

Enables loop guard/

restricted forwarding on aninterface

no lldp{transmit | receive} Enables reception and


no negotiationDisables auto-negotiation

on the interface

no spanning-tree bpdufilterDisables BPDU filter on the

interface

no spanning-tree loop-

guard

Disables loop guard/

restricted forwarding on aninterface

spanning-treepseudoRootId priority

mac-address

Sets the PseudoRoot macaddress and priority for the

spanning tree only in stepsof 4096

speed{ 10 | 100 | 1000 } Set port speed to 10, 100, or

1000 Mbps

switchportTo put an interface that is in

Layer 3 mode into Layer 2

mode for Layer 2

configuration

switchport acceptable-frame-type

{tagged |untaggedAndPrioritytagged}

Accept tagged oruntaggedAndPrioritytagged

switchport pvid } PVID value to be

configured on the port

spanning-tree link-type{point-to-point | shared} The link can be a point-to-

point link or can be a sharedLAN segment on which

another bridge is present

spanning-tree portfastSpecifies that port has only

hosts connected and hence

can transition to forwardingrapidly

spanning-tree port-priority Set priority


29/31

Examples of INTERFACE mode commands.

Many of the INTERFACE mode commands will not show the result, but if you navigateto EXEC mode and use the show spanning-tree detail command you can observe the

effect of the command.

spanning-tree restricted-tcn

(config-if)# spanning-tree restricted-tcn disable

spanning-tree pseudoRootId

(config-if)# spanning-tree pseudoRootId priority 4096 mac-address00:15:24:00:44:56


30/31

Mode: VLAN_CONFIG


no ports

[ ] [untagged([ ] )] [forbidden([ ]

Resets port list for the

VLAN

ports[add]

([ ]) [untagged

( )] [forbidden

]

Configures port list for the

VLAN

NOTE: without the add

parameter present the

command will act like a

replace

vlan activeMake the particular VLAN

active in the switch


31/31

Examples of VLAN mode commands.

To enter Vlan config mode you must first be on configure mode.

Example: (config)# vlan 200

By executing the above command you will create a vlan with id 200 if it does not exist

and enter vlan config mode for vlan with id 200, if the vlan already exists you will only

enter vlan config mode for that vlan.

Examples:

To add ports to a vlan.

(config-vlan)# ports add gigabitethernet 0/2The above command will add port 2 to the vlan.

(config-vlan)# ports add gigabitethernet 0/2-4

The above command will add port 2, 3 and 4 to the vlan.

(config-vlan)# ports add gigabitethernet 0/2 untagged gigabitethernet0/2

The above command will add port 2 to the vlan and to the untagged list.

(config-vlan)# ports gigabitethernet 0/3-4

The above command will add port 3 and 4 to the vlan. Note that the add parameter wasommited, This actually turns the command into a replace command and will remove all

ports not in the list of ports.

To remove ports from a vlan.

(config-vlan)# no ports gigabitethernet 0/3-4

The above command will remove ports 3 and 4 from the vlan.

(config-vlan)# no ports gigabitethernet 0/3,0/7

The above command will remove ports 3 and 7 from the vlan.

Cli Xpand Ip

Documents

Transcript of Cli Xpand Ip