Classic & Exotic Service, Inc.2032 Heide, Troy MI 48084 USAPhone: 1.248.269.9414E-mail: Parts@classicandexotic.comWWW: http://www.classicandexotic.com

SKU Product Name Price

Dash & Instrument Panel Trim

A-3090

Duesenberg A Dashboard Ignition PlateNickel plated brass ignition plate for use on the dashboard of Model ADuesenberg. The recessed back ground can be filled with black paint assubstitute for glass enameling. Material: Brass Finish: Nickel plated OAL: 4.425 OAW: 2.627 Top hole: .800 Top-bottom centers: 3.024 Bottom hole: .830 Mid holes: .530 1.025 centers

$ 309.00

J-5428

Duesenberg Instrument Panel Brass Molding SetBrass J-shape molding used to finish Duesenberg instrument panels. Canalso be used as binding molding for a variety of vintage cars and boats. Thisset consists of one 36" piece and two 16" pieces 1.062 heigh x .032 thick.

$ 185.50

MISC-0169

Auburn Dash High/Low Ratio Switch CoverBacking plate for the High/Low Ratio lever on the dashboard of 1932 - 1933Auburn V-12's using a two speed rear end. Finished in brass and requireschrome plating prior to use. May also fit other years and models of Auburn.Material: Brass; Finish: Natural; ID: .890; Thickness: .140; Width: 1.940 atthe widest .687 at the narrowest.

$ 103.00

MISC-0207 Tucker Instrument Cluster PanelTucker plastic instrument cluster panel. CNC machined from cast acrylicplastic. Excellent reproduction, ready to install.

$ 669.50

MISC-0252

Instrument Board Light Switch NutKnurled brass instrument board switch nut. Used with light switches installedon many cars of the 1930's and 1940's. Available in brass or chrome plated.Additional charge for chrome plating. Material: Brass; Finish: Natural orchrome; Thread: 3/8-27; OD: .565; OAH: .187; Knurling height: .140.

$ 6.25

RR-0020

Rolls Royce Phantom I Instrument Light HousingInstrument light housing used on Rolls Royce Phantom I. Cadmium platedand cast from bronze. Material: Bronze; Finish: Cadmium; Base: 2.035 L x2.152 W; Top OD: 1.220; Top ID: .937, .750; Base height: .625; Holes:.215.

$ 77.25

TUC-0006

Tucker Radio GrilleCNC machined replacement radio grille as used on Tucker automobiles.Ready to be chrome plated and installed. Tucker part number 200912.Material: Aluminum; Finish: Natural; Length: 6.090; Width: 6.016; Height:.396; Gaps: .250; Mounting holes: .193; Hole centers: 5.207, 5.724.

$ 309.00

TUC-0013 Tucker Dash Switch LeverTucker dash switch lever. For use with heater fan, headlights and cyclopsheadlight controls. Cast plastic with steel insert.

$ 128.75

Door

BODY-0009

Door Latch Lock Set ArmDoor latch lock set arm for use on Ternstedt Manufacturing door latchesthat are locked by a lock cylinder in the door. Used on many prewarautomobiles. Material: Carbon steel Finish: Natural Thickness: .056 Slotlength: .482 Slot width: .196 Hole ID: .190 Approx. OAL: 3.540 Approx.OAW: 1.690

$ 51.50

4/24/18. Prices subject to change. Page 1/9

SKU Product Name Price

BODY-0016-A,B

Interior Door Handle BezelInterior door handle bezel for Duesenberg and other custom bodied cars.Solid brass construction, ready for plating. Mounts through a 1" hole in thedoor panel. Available in two bearing lengths: 1/2" and 5/16". Material: Brass; Finish: Natural: THread: 31/32-20; OD: 1.875; ID: .628; OAL: .750.

$ 77.25

BODY-0017 Interior Door Handle BezelInterior door handle bezel for use on many prewar automobiles. Material:Brass; Finish: Natural; OD: 1.745; ID: .624; Notch: .264.

$ 77.25

BODY-0018

Interior Door Release Handle Splined SleeveSplined sleeve for door release handle. This sleeve threads into the doorhandle body and BODY-0019 nut holds the handle to the bezel. ID is splinedto mate with shaft on door latch mechanism. Material: Brass; Finish:Natural; Thread: 9/16-27, 9/16-18; OAL: .906; Journal OD: .625; Broachminor DIA: .382; Broach: 16 tooth.

$ 36.25

BODY-0019

Interior Door Handle Bezel NutNut to hold part BODY-0018 splined sleeve for interior door release handleto BODY-0016-A and B bezel. Material: Brass; Finish: Natural; Thread:9/16-27; OD: .750; Thickness: .125.

$ 31.00

BODY-0020

Door Remote Return SpringReturn spring for door remote release mechanism to return lever andhandle shaft. Material: Spring steel; Finish: Black; DIA: 7/8; Height: .185; Thickness: .040; Arbor DIA: .370.

$ 22.75

CAD-0140

1929-32 Cadillac Door Light SwitchChrome plated door jamb switch for use on 1929 - 1932 Cadillac. Ready toinstall. Material: Steel; Finish: Chrome; Bracket: 1.750 x 1.125; Bracketholes, centers: .190 1.375; Button OD: .375; Button height: .359.

$ 165.00

HIS-0123

Hispano Suiza Interior Door Handle BezelBrass interior door handle bezel for use on Hispano Suiza J-12. Material:Brass; Finish: Natural; Thread: M25 x 1.25; Thread length: 5mm; Length:19mm; OD: 44.5mm; ID: 17mm; Large ID: 15mm; Mid ID: 22mm.

$ 144.25

MAR-0022 Marmon V16 Window Weatherstrip RetainerMarmon V-16 brass window weatherstrip retainer. 3ft in length.

$ 231.75

MB-0003

Murphy Body Door Bumper SocketsMurphy body door bumper sockets CNC machined from solid aluminum.Two lengths available -can be shortened to fit a specific application. Bothsockets have .030 lip to overlap the door jams. Style #1: Outside width:1.355; Outside length: 1.719; Height: .488. Style #2: Outside width: 1.355; Outside length: 1.106; Height: .488.

$ 30.00

MB-0020

Murphy Body Footman LoopBronze footman loop used on many Murphy bodied cars. Used to hold doorcheck strap to door and body. Material: Bronze; Finish: Natural; Length:3.105; Width: .632; Height: .687; Stud holes: .272; Hole centers: 2.375; Bar length: 1.666.

$ 38.00

MB-0041-1,MB-0042-2

Murphy Body Door Latch Tongue ExtensionReproduction of fracture prone door latch component used on many Murphybodied cars.This piece rivets to the tongue to form the tongue assembly.Available for left and right side. Material: CR Steel, 11ga; Finish: Natural; Length: 5.260; Width: 2.780.

$ 87.75

MISC-0022 Molded Rubber Round Door BumperMolded rubber round door bumper. Many applications on antique classicvehicles including Delage of the 1930's. OD: 1 1/8; Height: 9/16.

$ 13.50

Page 2/9 4/24/18. Prices subject to change.

SKU Product Name Price

MISC-0068 MISC-0069

Dovetail Door Bumper SocketsIdeal door bumper socket. New fully machined aluminum part to replaceoriginal die cast Ternstedt Mfg. Co. part. Used with a steel capped rubberbumper, this dovetail socket has four mounting holes to hold the socket tothe car body, has four holes tapped for 8-32 screws to retain the coverplate and two pockets for bumpers. Available in two pocket sizes: 1/2'' or5/8''. Outside dimensions: 3'' long x 1 11/32 wide x 5/8 high. Interiordimensions: 1 1/8 x 9/16 deep.

$ 51.50

MISC-0274

Hooper Body Door Hinge BoltSteel door hinge bolt for use on Hooper bodied cars of the 1920's and1930's. Material: 4140 Steel; Finish: Natural; Thread: BSF 5/16-22; Thread length: .387; OAL: 1.667; Length under head: 1.425; Head OD:.768; Shaft OD: .387; Square: .305.

$ 41.25

MISC-0277

Hooper Body Door Hinge ScrewThis M7 x 1.00 door hinge screw has an oversized shank for repairing wornhinges. For use on Hooper bodied cars of the 1920's and 1930's such assome Hispano Suizas Bentley and Rolls Royce. Material: Steel; Thread:M7 x 1.00; Thread length: 8mm; OAL: 26mm; Head OD: 9mm; Headheight: 5mm; Shaft: 7mm; Length under head: 21mm.

$ 5.25

MISC-0310

Door Bumper Retaining BracketLaser cut retaining bracket used to install a rubber door bumper. For use onmany classic cars of the early 1930's such as Duesenberg and others. Material: Steel; Finish: Natural; Length: 1.260; Width: .806; Height: .484; Thickness: .060; Holes: .205, .336 centers.

$ 25.75

MISC-0324

Door Window Flapper HingeSpecial hinge with 5/8'' knuckles to cover the window opening when thewindow is rolled down. Sold in a six foot length - trim to fit application. Material: Steel; Length: 6ft; Thickness: .038; Knuckle: .625; Pin DIA: .093; Open width: 3.000.

$ 128.75

Fabric Fasteners

COR-0037-B Cord 810 812 Top Rivet ShortCord 810/812 top rivet with step. Material: Stainless steel; Finish: Natural; OAL: .890; OD: .263 - .311; Length under head: .783.

$ 15.50

MB-0032

Murphy Body Rear Window to Frame Thumb ScrewRear window to frame knurled thumb screw for use on Murphy bodied cars.Material: Steel; Finish: Natural; Thread: 1/4-18 x .627; Knurled DIA: .900;Slot width: .069; Head height: .800; Knurled height: .355; Length of head:.390.

$ 72.25

MB-0034 Murphy Body Convertible Top Corner Thumb Nut $ 87.75

MISC-0249 Dawson Plug SpringReturn spring for Dawson plugs for side curtain rods on open car bodies.Material: Steel; Length: 3.437; OD: .312; Wire: .020.

$ 7.75

P-0076

Upholstery ButtonTwo piece upholstery button for use on 1938 Packard and other makes &years. This button will require finishing: the open back must be sanded flatand attaching detail will have to be made. Material: Steel; Inner part: .028thick, 1.858 x .804; Outer part: .024 thick, 1.983 x .908

$ 20.75

Gear Shift Knob

4/24/18. Prices subject to change. Page 3/9

SKU Product Name Price

AM-0001

Aston Martin Gear Shift KnobGear shifter knob for Aston Martin DB2 and DB2/4 MK I II with four speedtransmission. CNC machined from; bakelite to match the original part. Material: Bakelite Thread: 5/16 British standard thread Ball OD: 1.705 Thread depth: 1.15

$ 154.50

Mirror

MB-0017

Murphy Body Rear View Mirror BracketRear view mirror windshield mounting bracket for the Beverly and otherclosed Murphy bodied cars. Can be adapted for use on a roadster. Material:Bronze; Finish: Natural; Thread: 10-24; OAL: 2.730; OAW: 2.410; Ovalend: 2.410 x .750; Holes centers on oval: .215 ID x 1.625 centers; Cut outID: .625; Holes, centers for threaded holes: 1.453.

$ 77.25

MB-0018

Murphy Body Rear View Mirror Bracket Clamp PlateBronze clamp plate used to hold the rear view mirror on the windshield ofMurphy bodied cars. Material: Bronze; Finish: Natural; Length: 2.032; Width: .375; Cut out ID: .562; Hole ID: .206; Hole centers: 1.453; Thickness: .064.

$ 51.50

MB-0018-1

Murphy Body Mirror Bracket Clamp ScrewBrass knurled screw used with the rear view mirror bracket clamp onMurphy bodied cars. Material: Brass; Finish: Natural; Thread: 10-24; Thread length: .343; OAL: .862; Length under head: .625; Head OD: .585; Body OD: .375, .242 long.

$ 25.75

MB-0019 Murphy Body Mirror MountMurphy body mirror mount. For use on Duesenberg Model J and other carswith Murphy coachwork.

$ 62.00

Pedals

TUC-0007

Tucker Accelerator PedalCNC Machined rubber accelerator pedal for Tucker. This part does not havea steel back plate and will need to be glued to the original back plate.Material: Rubber; Length: .625; Width: 2.032; Thickness: .250.

$ 103.00

TUC-0008

Tucker Brake & Clutch PedalCNC Machined rubber brake and clutch pedal for Tucker automobiles. Backis flat not recessed. Material: Rubber; Length: 4.50; Width: 3.00; Thickness: .500.

$ 103.00

Seat

MISC-0214

Brewster Coachwork Front Seat Locating SocketAluminum locating socket mounted to the body to prevent the seat fromsliding. Used on Brewster bodied cars such as Rolls Royce PI and PII.Original part number 17526. Two required per seat. OD: 1.946; Height:.182; Holes ID: .200; Center ID: .750.

$ 36.25

Sill Plates

AUB-0005

Auburn Boattail Speedster Sill PlateAluminum sill plate for use on Auburn Boattail Speedster.; Sill plate has anetched-in design and is an exact duplicate of an original sill plate as shownin the last photo. This item is available by special order only and has anapproximate delivery time of six weeks. This item will ship separately fromother items in your order. Material: Aluminum Finish: Natural Length:32.00 Width: 3.062 Thickness: .052 Inner bend DIA: .557 Width beforebend: 2.00 Width after bend: .312

$ 154.50

Page 4/9 4/24/18. Prices subject to change.

SKU Product Name Price

MAS-0002

Maserati Ghibli Sill PlateUniversal aluminum sill plate for Maserati Ghibli. Fits left and right side ofthe car but will need to be polished and trimmed to fit before installation.Maserati part number 115B064950. Material: Aluminum; Finish: Natural; Width: 1.727; Length: 36.00; Thickness: .050.

$ 130.00

MB-0010

Murphy Body Co. Door Sill PlatesDoor sill plate to fit all Murphy bodied cars of the 1920's and 1930's. Thesesill plates are an exact duplicate of the original shape are made from .040thick brass and measure 39'' x 2 1/2''. The Murphy logo is stamped into thebrass in the center of the plate. As shown in the photo the Murphy logohas been reproduced to exacting original detail and is an exact duplicate ofthe original. These sill plates are produced to be trimmed to fit and drilledby the purchaser. They will also need to be polished and plated by the purchaser. These plates will fit all Murphy bodied cars.

$ 133.00

P-0072

1935 Packard V-12 Front Sill PlatesNew photo engraved sill plates to fit many Series and models of PackardV-12. These perfect reproduction sill plates have been photo-etched into.032 brass and are exact duplicates of the original Packard parts. Theplates are ready to be drilled and plated. Left and right side available. Sillplates are 2.562 x 34.935. and will fit 1935 V-12 Convertible Sedan.Original Packard part numbers: 224317 (right) and 224318 (left).

$ 92.75

P-0073

1935 Packard V-12 Rear Sill PlatesNew photo engraved rear sill plates to fit many Series and models ofPackard V-12. These perfect reproduction sill plates have been photo-etched into .032 brass and are exact duplicates of the original Packard parts. The plates are ready to be drilled and plated. Right and leftside available. Sill plates are 1.375 x 17.187. Original Packard partnumbers: 224307 (right) and 224308 (left).

$ 77.25

STZ-0016

Stutz Door Sill Plate LongBrass engraved door sill plate for use on 1931 Stutz Model M. This is thelonger of the two sill plates we stock. Material: Brass; Length: 36.0; Width:2.516; Thickness: .042; Height: .553; ID Bend: .218.

$ 144.25

STZ-0017

Stutz Door Sill Plate ShortBrass engraved door sill plate for use on 1931 Stutz Model M. This is theshorter of the two sill plates we stock. Material: Brass; Length: 18.00; Width: 2.482; Thickness: .042; Height: .617; ID Bend: .218.

$ 144.25

STZ-0041

1929 1930 Stutz Model M Door Sill PlateBrass blank for fabricating 1929 - 1930 Stutz Model M door sill plate. Highlypolished brass stock with "STUTZ" engraved in proper location. Pleasenote: any appearance of scratches to the finish in photo is due to protectiveplastic covering to be removed after purchase - sill plate is not scratched.This sill plate must be custom fit to the car: trimming, forming and chromeplating is required for use. Material: HIghly polished brass; OAL: 24.500; Width: 3.00; Thickness: .0035

$ 144.25

Sun Visor

CAD-0117

Cadillac Sun Visor Mount Escutcheon PlateCadillac sun visor mount escutcheon plate. For use on all Cadillacs withclosed bodies Series 345BC 355BC 370BC and 452B. Cadillac partnumbers: Front: 4026900, group B3.1915; Rear: 4026899, group B3.1910.

$ 77.25

CAD-0118

1932-33 Cadillac Sun Visor WasherLaser cut steel washer for sun visor arm in 1932 - 1933 Cadillac LaSalle.For use on all closed body style Cadillac and LaSalle in Series 345 B C, 355 B C, 370 B C, 452 B. Cadillac part number 4206905, group numberB3.1955. Material: Steel; Finish: Natural; OD: 6.25; Thickness: .103; ID:.385 x .267.

$ 12.50

4/24/18. Prices subject to change. Page 5/9

SKU Product Name Price

CAD-0228-A, B

1930-31 Cadillac Sun Visor Frame Casting V8 V12 V16Sun visor frame casting for use on 1930 - 1931 Cadillac V-8 & V-16 and1931 V-12 sedan models. Left and right side available, sold separately.Material: Cast brass; OAL: 10 1/2; Visor channel length: 6 7/8; Visorchannel width: .300.

$ 180.25

CAD-0228-C, D

1930-31 Cadillac Sun Visor Support Casting V8 V12 V16Sun visor support casting for use on 1930 - 1931 Cadillac V-8 & V-16 and1931 Cadillac V-12 sedan models. Left and right available, sold separately.Material: Cast brass; Height: 5 1/2; Length: 7 1/2.

$ 154.50

MB-0007

Murphy Sun Visor FrameCast bronze sun visor frame as used on many Murphy Body Co. bodies. Can be used on the right or left side. For use on all Murphy bodies andcould be adapted to most windshields.

$ 460.00

MB-0009

Murphy Body Sun Visor GlassGreen tinted sun visor glass color matched to the original tint used onMurphy bodied cars. Buyer must cut glass to size prior to installation. Soldin a 21'' x 7 3/4'' x 7/32'' thick sheet.

$ 231.75

MB-0012

Murphy Sun Visor Inner BracketInner steel bracket to mount sun visor on Murphy bodied cars. Mounts onthe windshield frame to support sun visor. For use on all Murphy bodiesusing sun visors. Bracket is not drilled for mounting holes as these can varyfrom car to car. Finish: Natural; Hole ID: 3/8; Head OD: 15/16; Length:2.500; Width: 1.000; Thickness: .118.

$ 33.00

MB-0012-L

Murphy Sun Visor Left BracketLeft steel bracket to mount sun visor on left side of windshield frame. Offsetdesign to accommodate internal tensioner in visor frame. For use on allMurphy bodies using sun visors. Requires expanding tensioning sleeve tobe installed after drilling mounting holes and polishing prior to chromeplating. Finish: Natural; Thickness: .118; Head OD: .935; Length: 2.500; Width: 1.000.

$ 33.00

MB-0012-R

Murphy Sun Visor Right BracketRight steel bracket to mount sun visor on right side of windshield frame.Offset design to accommodate internal tensioner in visor frame. For use onall Murphy bodies using sun visors. Requires expanding tensioning sleeveto be installed after drilling mounting holes and polishing prior to chromeplating. Finish: Natural; Thickness: .118; Head OD: .935; Length: 2.500; Width: 1.000.

$ 33.00

MB-0013

Murphy Sun Visor 5/16-18 Tensioning BoltAcorn Bolt to attach mounting bracket to visor frame and tension visor afterinstallation. Duplicate of original ''Murphy'' head profile. For use on allMurphy bodies. Material: 303 SS; Finish: Natural; Thread: 5/16-18; Thread length: 1.00; OAL: 2 1/2; Head height: 1/2, hex 9/16; Lengthunder head: 2.00; Hex: .562.

$ 15.50

MB-0014

Murphy Sun Visor Acorn NutAcorn nut to hold sun visor frame to inner bracket. This is an exact duplicateof the original Murphy coachbuilder head profile. Material: Steel; Thread:5/16-18; Hex: .562 x .450 high.

$ 33.00

MISC-0160

Ghia Body Dark Amber Sun VisorDark amber tinted plastic sun visor material. Duplicate of visor materialoriginally used by Ghia in the mid-fifties and possibly used by otherEuropean coach builders. This item is available in custom sizes up to 24'' x24''. Contact us directly for information and to order custom sized visors.

$ 54.25

Page 6/9 4/24/18. Prices subject to change.

SKU Product Name Price

P-0003

1953 Packard Caribbean Sun Visor MountBronze reproduction of sun visor mount, machined and ready for plating.This is a replacement for the fragile and difficult to replate die cast part used on 1953 Packard Series 2250-77 2352-77 2350-97 and other cars.Packard part number 385576 ''Bracket - Sun Visor''. Two required pervisor.

$ 56.75

P-0004

1953 Packard Caribbean Sun Visor Pivot ArmBronze reproduction of sun visor arm. This is a replacement for the fragileand difficult to replate die cast part used on 1953 Packard Series 2250-77 2352-77 2350-97 and other cars. Packard part number 385576 ''Bracket Sun Visor''. Two arms required per visor.

$ 56.75

Windows

BODY-0011

Locking Windshield HandleLocking windshield handle for use on many pre-war custom coachworkcars. Material: Bronze Finish: Natural OAL: 5 1/4 Mounting pin hole:.120

$ 128.75

BODY-0011-A

Locking Windshield Handle BezelLocking windshield handle bezel for use on many prewar custom coachworkcars. Material: Bronze; Finish: Natural; Countersunk screw holes: .200; Slot width: .540; Slot length: 1.485.

$ 77.25

MB-0001

Window Flapper Spring Style 1Stainless steel spring for closing window flappers. Commonly used onMurphy bodies, this style has clock wise wind long ends coming off on thesame side. Also used by Brunn Rollston LeBaron and others. Measures1.260 with a .218 OD wire. Wire thickness is .040. Ends can be trimmedand bent if needed.

$ 8.75

MB-0002

Window Flapper Spring Style 2Stainless steel spring for closing window flappers. Commonly used onMurphy bodies, this style has counter clockwise wind with long ends comingoff on opposite sides. Also used by Brunn Rollston LeBaron and others. Measures 1.130 OAL with a .218 OD wire. Wire thickness is .040. Endscan be trimmed and bent if needed.

$ 8.75

MB-0004

Window Flapper Spring Style 3Stainless steel spring for closing window flappers. Commonly used onMurphy bodies, this style has clockwise wind with long ends coming off onopposite sides. Also used by Brunn Rollston LeBaron and others.Measures .935 OAL with a .169 OD wire. Wire thickness is .034. Ends canbe trimmed and bent if needed.

$ 8.75

MB-0005

Window Flapper Spring Style 4Stainless steel spring for closing window flappers. Commonly used onMurphy bodies, also used by Brunn Rollston LeBaron and others.Measures .584 OAL with a .224 OD wire. Wire thickness is .040. Ends canbe trimmed and bent if needed.

$ 8.75

MB-0032

Murphy Body Rear Window to Frame Thumb ScrewRear window to frame knurled thumb screw for use on Murphy bodied cars.Material: Steel; Finish: Natural; Thread: 1/4-18 x .627; Knurled DIA: .900;Slot width: .069; Head height: .800; Knurled height: .355; Length of head:.390.

$ 72.25

MB-0033

Murphy Body Windshield to Front Top Bow Mounting PinWindshield to front top bow mounting pin for use on Murphy bodied cars.Material: Steel; Finish: Natural; Thread: 5/16-24 x .660; OAL: 1.250; Headlength: .590; Head DIA: .480; Slot width: .072.

$ 41.25

MB-0036

Murphy Body Lower Window ChannelLower window channel for use on Murphy bodied cars. Material: Carbonsteel; Finish: Natural; Length: 31.000; Channel width: .330; Height: 1.000; Thickness: .056.

$ 123.75

4/24/18. Prices subject to change. Page 7/9

SKU Product Name Price

P-0200 P-0201

1934-39 Packard Vent Window Regulator GearWindow vent regulator gear for use on 1934 - 1939 Packard Eight Super 8and Twelve. Right and left side available. Difference between left and rightis in the orientation of the teeth. Material: Phosphor bronze; OD: 1.375; ID:.500; Thickness: .468.

$ 128.75

Page 8/9 4/24/18. Prices subject to change.

Terms and Conditions

Delivery

Returns

We ship worldwide Monday through Friday. Our normal handling time is 24 hours or less - manyorders ship the same day they are placed. Some items may require an additional handling time -see individual product descriptions for information. Expedited domestic shipping is through UPS. For expedited UPS shipping, orders must be receivedby 1PM EST. Orders received after 1PM EST will ship the next business day. UPS business daysare Monday - Friday. Next Day Air orders placed on Friday will be delivered on Monday. In some instances, non-expedited domestic orders may be shipped by USPS Priority Mail at ourdiscretion. If your order must be shipped by UPS Ground, please note that when placing yourorder. International shipping is through USPS Express Mail or UPS Worldwide services. We do not ship by Fedex - that includes domestic and international orders. Shipping cost is determined by package weight and shipment destination. Shipping cost for yourorder can be viewed in your shopping cart by entering a shipment destination. Please note that our warehouse is closed to the public and we are unable to accommodate localpickups of orders.

Items must be returned in new unused condition within 14 days of receipt. Items returned after 14days of receipt are subject to a 15% restocking fee. No returns will be accepted after 90 days fromthe original purchase date. Original shipping charges are non-refundable. Refunds will be issuedupon receipt and inspection of the returned item and will be issued in the manner payment wasreceived. For returns made after 60 days, refunds will be issued by check only. Items which are cut to order and sold by the foot and items made to customer specified lengths orwidths are not returnable. When returning an item, please include a copy of your original invoice and send the item to: Classic & Exotic Service, Inc.Attn: Returns2032 Heide (USPS only)2000 Heide (UPS, FedEx only)Troy, MI 48084 USA All returns must be mailed - we cannot accommodate in-person returns.