Class 185 ‘Desiro’ Pack For Train Simulator · Class 185 Pack 2018 U s i n g i n S c e n a r i...
Transcript of Class 185 ‘Desiro’ Pack For Train Simulator · Class 185 Pack 2018 U s i n g i n S c e n a r i...
Class 185 ‘Desiro’ Pack For
Train Simulator
Image © Geof Sheppard 2017
Class 185 Pack 2018
Contents Requirements - 1 How to Install - 1
Liveries - 2 Features - 4
Setting Up - 4 Headlights - 4
Using in Scenarios - 7 Destination Chart - 7
Special Note - 7 Credits - 8
Requirements
You must have DTGs Great Eastern Main Line London-Ipswich route and European Loco & Asset Pack installed to able to use this pack.
How to Install
To Install, copy the all folders (i.e. Assets folder) included to your main TS
installation folder (usually found at “C:\Program Files (x86)\Steam\steamapps\common\RailWorks”). If Windows prompts you to
override any files, click yes to all.
1
Class 185 Pack 2018
Liveries
First Transpennine Express “Dynamic Lines” (Original to Pack)
2
Class 185 Pack 2018
First Transpennine Express (New) (New to Pack - Created by Lewis Clowes)
Factory (Plain) Livery (New to Pack)
First Transpennine Express “Barbie” (New to Pack)
3
Class 185 Pack 2018
Features
New features (added by the pack) include new Headlights and Central door
Locking (CDL) lights included on all liveries. The sound pack from V4.1 of the train has also been included.
Quick Drive consists for all Liveries.
Several fixes have also been applied (these include the reverser which is working properly - Forward is now notch 2 instead of notch 4 and Reverse
is now notch 4 instead of notch 2).
Setting Up
When you first enter the train you must press ‘E’ on your keyboard to unlock the startup key which unlocks the reverser.
You can now set the direction on the reverser as needed.
Headlights
The headlight configuration can be set by the switch found in the cab or by pressing ‘H’ on the keyboard (‘Shift + H’ to select previous config). The
config sequence is as follows; First/Default Setting - Tails, Second - Markers only, Third - Day Time setting (Markers plus day headlight), Fourth
- Night Time setting (Markers plus night headlight). (Note - Each end is controlled separately meaning on a normal config the
back end will always have the tail lights on unless you switch ends to change it.)
4
Class 185 Pack 2018
Each config is shown below;
Tail Lights
5
Class 185 Pack 2018
Markers Only
Day Time
Night Time
6
Class 185 Pack 2018
Using in Scenarios
The numbers for the trains need to be in this order ‘destination 185 number’
(with no spaces and letters must be in lower case) (e.g. a185101 corresponds to Manchester Airport and 185101 or m185101 which
corresponds to Cleethorpes and 185101).
Destination Chart Manchester Airport a Carlisle o Thirsk " Manchester Piccadilly b Middlesbrough p Stockport : Leeds c Barrow-In-Furness q Stalybridge } Newcastle d Huddersfield r Selby { York e Glasgow s Seamer + Edinburgh f Manchester Victoria t Scunthorpe _ Liverpool g Sheffield u Motherwell ) Blackpool h Penrith w Malton ( Windermere i Lancaster x Lockerbie * Hull j Durham y Grimsby Town & Grange-over-Sands k Not In Service z Doncaster ^ Preston i Yarm > Dewsbury % Cleethorpes m Warrington < Darlington # Scarborough n Thornaby ? Special -
Special Note For those who have trouble with the Class 185 cab, make sure that the route that are running it on has the DTG GEML route as a requirement (ticked in the world or scenario editor - Under RSC\GEML).
7
Class 185 Pack 2018
Credits
Finchy - Creating the original train
Jake Fuller (nymr1) - Creating this Pack Lewis Clowes - Creating the ‘New’ FTPE Livery
8