Value-Added BenefitsEasy to transport and install • Built-in forklift pockets for easier transport

• 94” transport and install height fits vertically under most doorways

Easy to load • 27” feed opening is the largest in the industry

Fast and efficient • 45 second cycle time is one of the fastest in the industry

Easier to service and maintain • 10 HP motor eye-level, side-mounted power unit • Eye-level oil sight and temperature gauge provides visible indicator of oil volume, cleanliness

and temperature to avoid repairs• UL listed solid state electronic controls• NEMA 4 control panel provides protection against windblown dust, splashing water and

hose-directed water• High-performance HD32 hydraulic oil allows wider temperature operating range• High-quality, outdoor protective paint finish protects against oxidation and rust

Enhanced safety features • Auto Open Gate• Safety cable thru cylinder to protect in the event of cylinder pin failure• Emergency stop button• Front and rear retaining teeth stabilizes bale and increases density

Safety, quality and performance at a great price make the 6030HDB our most popular baler.

Wastequip’s 6030HDB Baler is perfect for cardboard baling. It has a powerful 10HP motor, quick 45 second cycle time, and built-in forklift pockets. With a height under 8 feet, it fits under most doorways, and the 27” feed opening is the largest in the industry. Combined with an eye-level, side-mounted power unit, it’s the perfect baler for operators, installers and service technicians. And, the best part is the great price for a baler packed with industry-leading features.

7” x 3” Built-in Forklift Pockets

94” Transport/ Install Height

27” Feed Opening

Eye-Level Power Unit

Eye-Level Oil Sight and

Temperature Gauge

Ergonomic Vertical Door

Handle

Magnetic Interlock

VERTICAL BALER6030HDB

Built-in forklift pockets allow for ease of transport and installation. Baler can be easily loaded on a standard flatbed by a forklift.

SpecificationsCYLINDER BORE 6”

CYLINDER ROD 3.5”

CYLINDER STROKE 48”

MOTOR HP 10

PHASE & VOLTAGE 3 PHASE 208-230/460

BALE WEIGHT OCC 800-1,000#

BALE SIZE 60” X 30” X 48”

FEED GATE OPENING 27” X 60”

FEED HEIGHT 49”

PLATEN AREA (sq. inches) 1,725

PLATEN FORCE (lbs.) 56,500

OPERATING PRESSURE 2,000 PSI

CYCLE TIME (sec.) 45

CONTROL VOLTAGE 110 V

PUMP SIZE GPM @ 1850 RPM 13

SHIPPING WEIGHT (lbs.) 4,000

*Optional Features: bale wire guides, oil heater, and full bale light

VERTICAL BALER6030HDB

Wastequip is the leading North American manufacturer of waste and recycling equipment for collecting, processing, and transporting recyclables and solid or liquid waste. © Wastequip. All rights reserved. Specifications subject to improvement without notice. Equipment displayed should be operated by properly trained personnel. Operators should become familiar with OSHA, ANSI, and any other applicable standards or laws for using this equipment. Improper use, misuse, or lack of maintenance could cause injury to people and/or property. Photos used in the literature are illustrative only. We assume no liability or responsibility for proper training/operation of equipment not manufactured by Wastequip. We reserve the right to make changes at any time without notice. Information contained within this literature is intended to be the most accurate available at time of printing.

Tel: 877.468.9278 | sales@wastequip.com | www.wastequip.com

WQP003-042018

UNLESS OTHERWISE SPEFICIED: UNITS ARE INCHES AND TOLERANCES:

Fractional: 1/16"

THIS DRAWING IS THE PROPERTY OF WASTEQUIP, INC., IS CONFIDENTIALMUST NOT BE MADE PUBLIC OR COPIED, AND IS SUBJECT TO RETURNON DEMAND. ALL RIGHTS OF DESIGN OR INVENTION ARE RESERVED.

REF.

Sheet No.

Date: Weight:

6030HDB

8/3/2017 #Drawing Number:222881MANUALAS BALER

Scale:

Location ID:

dgrantDrawn By:DXF:

Job #:

Description:

Previous Part #:

© Wastequip, Inc. 2008DO NOT

SCALE DWG

Angular: 1

Revision:

Revision Date:WASTEQUIP

A

80 1/4" OAW 45 3/4" OAD

48 5/8"FEED

HEIGHT

82 3/8" REQ CLEARANCE

49"FEED

HEIGHT

27"GATE

OPENING

140"OAH

94"

45 3/4"OAD

101 3/4"

UNLESS OTHERWISE SPEFICIED: UNITS ARE INCHES AND TOLERANCES:

Fractional: 1/16"

THIS DRAWING IS THE PROPERTY OF WASTEQUIP, INC., IS CONFIDENTIALMUST NOT BE MADE PUBLIC OR COPIED, AND IS SUBJECT TO RETURNON DEMAND. ALL RIGHTS OF DESIGN OR INVENTION ARE RESERVED.

REF.

Sheet No.

Date: Weight:

6030HDB

8/3/2017 #Drawing Number:222881MANUALAS BALER

Scale:

Location ID:

dgrantDrawn By:DXF:

Job #:

Description:

Previous Part #:

© Wastequip, Inc. 2008DO NOT

SCALE DWG

Angular: 1

Revision:

Revision Date:WASTEQUIP

A

80 1/4" OAW 45 3/4" OAD

48 5/8"FEED

HEIGHT

82 3/8" REQ CLEARANCE

49"FEED

HEIGHT

27"GATE

OPENING

140"OAH

94"

45 3/4"OAD

101 3/4"

Appendix 6 ­ Frontload and Roll­off Specs

Appendix 6 - Frontload and Roll-off Specs

Appendix 9 - CNG Frontload Trucks & Roll-off Trucks

Appendix 9 - CNG Frontload Trucks & Roll-off Trucks

Appendix 9 - CNG Frontload Trucks & Roll-off Trucks

Appendix 9 - CNG Frontload Trucks & Roll-off Trucks

Appendix 7­ Compactor Specs

Value Added Benefits

Improved efficiency • Quick cycle times improve employee efficiency; trash is compacted in just 30 seconds.

Increased performance • 18” of ram penetration and over 28,000 lbs. of ram force ensure maximum compaction.

Standard features included at no additional charge

• Patented 4-1 head can be changed to feed from front, rear, left side or right side. • Full Container Light alerts you when trash is ready for pickup.• Magnetic interlock prevents the compactor from operating if door is open or container is not

properly in place. • Low temperature oil feature works well in hot or cold climates.*• Driver light is illuminated when it is safe for the hauler to remove the container.• Built-in stops hold container in place to prevent movement during compaction.

Ease of ownership • Purchase, rental and leasing programs available.

Strong warranty • 1-1-1 warranty (1-year structural, 1-year parts and 1-year labor).

ACCU-PAK VERTICAL COMPACTORSD-400, D-600 & D-800

Designed for restaurants, motels, grocery stores, apartment complexes or other locations where space is limited.

*Use of an oil heater or extreme cold weather hydraulic oil is recommended in extreme cold conditions.

With a 30-second cycle time, the Accu-Pak compactor with a patented 4-in-1 head design is the only vertical compactor in the industry that can be changed to front, rear, left or right feed in the field.

Available with 3, 4, 6 or 8 yard front load containers.D-800 model designed to be loaded from dock or stand.D-300 container comes with casters.

Standard Features• Short 30 second cycle time

• Full container light

• Low temperature oil

• Operational and service manual

• Primed and painted in several colors

Optional Features• Chute extension• Loading platform with safety rail• Through the wall installation• Thermostat oil controlled heater• Automatic odor suppression system• Biodegradable oil• Single phase 220 volt or 110 volt available

* Specifications are the same as the D-600, except where indicated.

Wastequip is the leading North American manufacturer of waste and recycling equipment for collecting, processing and transporting recyclables and solid or liquid waste. December 2016 © Wastequip, all rights reserved. Specifications subject to improvement without notice. Equipment displayed should be operated by properly trained personnel. Operators should become familiar with OSHA, ANSI and any other applicable standards or laws for using this equipment. Improper use, misuse, or lack of maintenance could cause injury to people and/or property. Photos used in the literature are illustrative only. We assume no liability or responsibility for proper training/operation of equipment not manufactured by Wastequip. We reserve the right to make changes at any time without notice. Information contained within this literature is intended to be the most accurate available at time of printing.

WQP025-122016

Tel: 877.468.9278 | sales@wastequip.com | www.wastequip.com

Standard Color Choices*

White Gray Black Teal Med. Blue Dark Blue Med. Green Dark Green Cream Yellow Orange Red Burgundy Brown

Colors shown are as accurate as printing allows. The actual color is subject to variation from the printed color sample. Color choices vary by plant location. Please contact your local sales representative for available colors. Custom colors are available upon request and are subject to an additional charge.

WASTECMEMBER

Was

te E

qipm

ent Technology Association

TMReplacement parts available online at www.gotoparts.com.SPECIFICATIONS

Charge Box• Wastequip rating: 0.5 cu. yds.• Wastec rating: 0.42 cu. yds.• Compactor weight with stand and container• 3,340 lbs. (D-300 / 3-yard)• 3,540 lbs. ( D-400 / 4-yard)• 3,740 lbs. ( D-600 / 6-yard)• 3,940 lbs. ( D-800 ) / 8-yard)

Ram• Ram height: 36”• Ram penetration: 18.00”• Face plate: 7-gauge, 48” W x 36” H• Base plate: 7-gauge, 47-1/2” W x 36”• Side plates: 7-gauge, 36” W x 19-11/16” H

Compactor Head• Sides: 11-gauge, (2) 83-1/2” W x 19” H• Top deck: 11-gauge, (2) 83-1/2” W x 21” Ht

Electrical• Fan-cooled electric motor: 3hp• Voltage: 208/230/460, 3-phase 60 Hz• Power box: UL rated, TEFC housing• Automated cycle operation: turn-key switch-ram

extends, retracts and stops automatically

Hydraulic Performance• Pump: 2.8 gpm• Pump type: Gear• Hydraulic oil tank: 8.7 gallon reservoir• Cylinder bore/rod/stroke: 4” bore, 2” rod 16” stroke• Normal ram face pressure: 25,100 psi• Maximum ram face pressure: 26,400 psi• Normal ram psi: 2,000• Maximum ram psi: 2,100• Cubic yard per hour: 49 cu. yd./hr.• Power unit location internal• Cycle time: 30 seconds

ACCU-PAK VERTICAL COMPACTORS

E a s y t o u s e

M a i n t e n a n c e f r i e n d l y

B a l e w e i g h t s u p t o 1 , 1 0 0 l b s .

S i d e - m o u n t e d h y d r a u l i c p o w e r u n i t

Heavy-Duty Vertical Baler

H E A V Y - D U T Y V E R T I C A L B A L E R

S h o p p i n g P l a z a s

H o s p i t a l s

S u p e r m a r k e t s

H o t e l s / M o t e l s

S c h o o l s

P a p e r C o n v e r t e r s

P a p e r S t o c k D e a l e r s

M R F s / R e c y c l i n g C e n t e r s

R e t a i l e r s

D i s t r i b u t i o n C e n t e r s

M a n u f a c t u r i n g P l a n t s

Heavy-Duty Vertical Baler

H E A V Y - D U T Y V E R T I C A L B A L E R

Easy to Use and Maintenance FriendlyA Marathon Vertical Baler is precision-built for ease of use and maintenance-friendly access. Features such as the side-mounted, self-contained power unit, front-facing panel box, and feed gate interlock system all add up to a reliable baler.

Your baler can also be equipped with optional features that add even more efficiency and ease of use. An automatic bale ejector that activates when the bale door is opened is available. The ejector does not extend beyond the wire guides, enabling the unit to be placed against the wall. Wire guides eliminate the need to go behind the baler for a complete front tie-off system. A Bale Made light illuminates when a bale is made to notify the operator when it is time to eject the bale, and a lockable electrical disconnect can be added for local Lock-Out/Tag-Out.

Front opening control panel eliminates the need for 48" side clearance as required by NEC ® standards.

For more information or to order, call (800) 269-7237 or visit us at www.marathonequipment.com.

Fixed retainer teeth on the door and rear of the baler reduce material springback.

H E A V Y - D U T Y V E R T I C A L B A L E R

Wire Guides Bale Made Light Lockable Disconnect

For more information or to order, call (800) 269-7237 or visit us at www.marathonequipment.com.

An interlock system is incorporated into the feed gate switch.

Platen features replaceable high-density polyethylene guides to absorb side thrust and replaceable cast iron shoes.

The standard chain bale ejector is manually set after the bale door is opened.

Standard controls: key lock On/Off Auto Cycle, Emergency Stop, and Platen Raise/Lower. A Baler Ready light indicates the baler is operational. Also available with Bale Made light and electrical disconnect (shown).

An optional automatic bale ejector is also available. It is actuated when the bale door is opened.

If there is an attempt to override the interlocks, the panel box features a programmable "smart" relay control system that disables the baler. The relay adds diagnostic and trouble-shooting capabilities.

An automatic feed gate opens at the end of each cycle as the platen is retracted.

The side-mounted, self-contained power unit is convenient for maintenance and servicing. It can be unbolted from the body during installation if necessary.

Other Available Options: Oil Heater

Weather Cover for Panel Box

SO Cord

Options:

WET WASTE VERT ICAL COMPACT IONH E A V Y - D U T Y V E R T I C A L B A L E R

Marathon Equipment CompanyP.O. Box 1798Vernon, AL 35592-1798(800) 269-7237www.marathonequipment.com

NJPA Contract #060612-ESG

www.doveresg.com

Pictures in this literature are illustrative only. Specifications are subject to change without notice in order to accommodate improvements to the equipment. Complies with ANSI standard Z245.2, all applicable OSHA regulations, and certified under WASTEC’s Stationary Compactor Certification Program. Products must be used with safe practice and in accordance with said regulations and standards.

© 2014 Marathon Equipment Company. All rights reserved. Printed in USA. | SWS-M00109-033014

Rental and Leasing Programs Available

For detailed specifications, recommendations, or free economic studies comparing various systems, contact Marathon Customer Care at (800) 269-7237.

Authorized Dealer:

V-6030 HD Vertical BalerPerformance V-6030 HD

Cylinder (Bore, Rod, & Stroke) 6" x 3.5" x 48" (152mm x 89mm x 1219mm)

Pump Flow (Gear Pump) 10.5 gpm (39,7 lpm)

Motor 10 hp (1,750 rpm) (7,46 kW)

System Pressure 2,000 psi (13790 kPa)

Maximum System Pressure 2,200 psi (15168 kPa)

Maximum Platen Force 62,200 lbs. (277 kN)

Platen Pressure 37 psi (255 kPa)

Cycle Time 56 sec.

Electrical Equipment

Electrical 208/230/460 3-phase

Electrical Control Voltage 120 VAC

OFF/ON Security Key Switch; 3-Position Selector Switch; EMERGENCY STOP Button; IEC Motor Starter and Overload, Programmable Smart Relay UL® and CUL® Listed

Bale Size Data

Bale Size 60"W x 30"D x 48"H (1524mm x 762mm x 1219mm)

Bale Volume 50 cu.ft. (1,42 m3)

Bale Weight (OCC) Up to 1,100 lbs. (499 kg)

Number of Bale Ties (14 ga x 14' L)

5

Total Baler Weight 4,682 lbs. (2124 kg)

Dimensional Data

A - Overall Width 87" (2210mm)

B - Overall Depth 411⁄2" (1054mm)

C - Overall Depth (w/optional wire guides)

541⁄2" (1384mm)

D - Overall Height 140" (3556mm)

E - Feed Height 481⁄4" (1226mm)

F - Feed Opening Width 24" x 61" (609mm x 1549mm)

G - Feed Opening Height 25" (635mm)

H - Bale Door Clearance 58" (1473mm)

Front View

Side View

A

E

G

F

Optional Wire Guides

Optional Auto Eject

C

B

D

Wa

ste

Eq u i p m e n t Te c

hn

olo

gy Associatio

n

Appendix 6 ­ Frontload and Roll­off Specs

Appendix 6 - Frontload and Roll-off Specs

Appendix 7­ Compactor Specs

Appendix 7­ Compactor Specs

Appendix 7­ Compactor Specs

Appendix 9 - CNG Frontload Trucks & Roll-off Trucks

Appendix 9 - CNG Frontload Trucks & Roll-off Trucks

Appendix 9 - CNG Frontload Trucks & Roll-off Trucks

Appendix 9 - CNG Frontload Trucks & Roll-off Trucks

“D”

“D”

34’ 4” (approx.) “C” “A”

“D”

“B”

CONTAINER

COMPACTOR

18’ 3” (219”)

Minimum

20’9”(249”)

(O.C. Containers)

22’0”(264”)

(R.C. Containers)

CEILING WITH RECTANGULAR CONTAINER AT FULL TILTCEILING WITH OCTAGONAL CONTAINER AT FULL TILT

CEILING WITH HOIST ONLY AT FULL TILT

CEILINGS GIVEN ARE FOR A TYPICALHOIST, SOME MODELS MAY BE HIGHER

STANDARD22’ ROLL-OFFHOIST

CONTAINER COMPACTOR

See concrete pad requirements below(under Compactor Installation)

Stationary Compactor

34’ 4” (approx.) “C”

18’ 3” (219”)

Minimum

CEILING WITH HOIST ONLY AT FULL TILT

CEILINGS GIVEN ARE FOR A TYPICALHOIST, SOME MODELS MAY BE HIGHER

22’0”(264”)

(Self Containers)

CEILING WITH CONTAINER AT FULL TILT

“B”

STANDARD22’ ROLL-OFFHOIST

Self-contained volume (cu. yd.) 16 20 25 30 35 20 25 30 35 38

Length overall (in.) 184 ½(C) 208 ½(C) 238 ½(C) 268 ½(C) 298 ½(C) 218(C) 218(C) 248(C) 278(C) 299(C)

Height overall (in.) 100(B) 100(B) 100(B) 100(B) 100(B) 100(B) 100(B) 100(B) 100(B) 100(B)

MODEL 265IP MODEL 265XP

See concrete pad requirements below(under Compactor Installation)

Self-Contained Compactor / Container

APPROACH SPECIFICATIONS

COMPACTIONTERMINOLOGY

T H E B E N E F I T S O F

SAVES MONEY • IMPROVES SAFETY • ENHANCES AESTHETICS • INCREASES USABLE SPACE

Compaction – Reducing the size and volume of material by compressing and crushing.

Stationary Compactor – A machine that compacts refuse into a detachable container at the site of generation.

Pre-Crusher Dry Waste Compactor – A machine that pre-crushes large bulky items such as steel drums and pallets prior to being compacted into the container.

Compaction Container – A steel reinforced container into which a stationary compactor compacts refuse.

Self-Contained Compactor – A unit in which the compactor is integrated structurally to the compaction container and the entire machine is taken to the disposal site.

Charge Box – The area, measured in cubic yards, in front of a compactor ram into which refuse is placed (L x W x H).

ClearTop Opening – The length and width of the opening above the charge box.

WQP022-092019 877-468-9278 I www.wastequip.com I sales@wastequip.com

Concrete Pad Concrete pad preferred dimensions are 10' wide and a length of 5' greater than the combined length of the compactor and container (not enclosed). Examples:• Pad: 10' wide x 40' long for 2

cu. yd. stationary and container• Pad: 10' wide x 35' long for 35

cu. yd. self-contained

• Pad: 10' wide x 12' long for vertical compactor

The pad should be a minimum of 3,000 p.s.i. concrete, wire mesh reinforced and 6" thick.

Electrical A lockable fused disconnect box (customer furnished) must be within sight and no more than 50' away from the main control panel.

This equipment conforms to all applicable ANSI Z245.2/.21 Safety Standards.

Safety Standards The installation must comply with recommended ANSI and OSHA standards. There must be interlock switches on the hopper access gate or chute/doghouse doors. A “Hold to Run” button may also be required.

Compaction Containers Available in octagonal and rectangular styles from 20 to 40 cu. yd.

Emergency Controls E-stop controls should be readily accessible to the operator or located within 3' of the point of operation, the material feed area, or if chute-fed, within 3' of access door.

Stationary volume (cu. yd.)

25 27 30 35 40 245 345 350 445 450 550 645

Length overall (in.) 171 1/2(C) 189 1/2(C) 207 1/2(C) 237 1/2(C) 270 1/2(C) 126(A) 146(A) 187 1/2(A) 187(A) 236(A) 281(A) 263(A)

Height overall (in.) 105(D) 105(D) 105(D) 105(D) 105(D) 48 1/8(D) 48 1/8(D) 48 1/8(D) 48 1/8(D) 48 1/8(D) 49 5/8(D) 48 1/8(D)

Cubic yard = 202 gallons(Approximate equivalent of six 33-gallon bags or seven 30-gallon bags)

COMPACTOR INSTALLATION

Tel: 877.468.9278 | www.wastequip.com

Stationary

WASTE TYPE: Dry waste including mixed paper, corrugated, wood, plastic, etc.

APPLICATIONS: Retail/department stores, industrial, warehouses

SIZES: 2 – 15 cubic yard stationary is attached to a 40 cubic yard container

Self-Contained WASTE TYPE: Wet waste including food processing, medical, etc.

APPLICATIONS: Supermarkets (produce/meat waste), restaurants, malls, hospitals

SIZES: 20, 30, 35 cubic yard self-contained

1 SAVES MONEY

• Less Labor. No need to break up boxes or carry trash outside to container.

• Reduces Collection Costs. Reduces the cost of transporting refuse to the disposal site. A compactor can eliminate 3 out of 4 trips.

• Reduces Fire Hazards. Saves on insurance costs.

• Reduces Insect/Rodent Problems. No need to call an exterminator.

2 IMPROVES SAFETY AND SECURITY

• Prevents Unauthorized Access To Waste. A sealed container keeps others from viewing any confidential data. A steel security chute prevents merchandise from being taken out the back door.

• Avoids Unauthorized Disposal. Prevents others from using your container for disposal of their trash or hazardous waste.

• Discourages Scavengers. Keeps scavengers out of your container.

• Improves Safety. Enclosed or chute fed compactor eliminates need for employees to take material outside.

3 IMPROVES AESTHETICS

• Prevents Wind-Blown Trash. Reduces need to sweep parking lots.

• Controls Odor. A sealed compaction system reduces odor.

• Extends Pavement Life. Reduces wear and tear on parking surfaces by heavy collection vehicles.

4 INCREASES USABLE SPACE

• Saves Inside Storage Space. No need to use storeroom space for refuse.

• Saves Outside Parking Space. Fewer containers outside means more customer parking spaces.

Compacting waste reduces the size and volume of material through compressing and crushing. This reduces the number of hauls, saving money.

Not all generators of solid waste and recycling material can justify compaction equipment. A business with one 6 cubic yard container emptied once a week may not need a compactor. Larger volume waste and recycling generators are more likely prospects. A generator of 30 to 40 cubic yards of material weekly might justify a vertical compactor. One that generates 60 to 150 cubic yards weekly could use a stationary compactor with a detachable container or a self-contained liquid-tight compactor.

Volume of Waste Generated Will the compactor be adequate to handle the volume generated, particularly at peak loading times?

Size of Waste What are the dimensions of the largest box, bag, etc.? Is the clear top opening large enough to accommodate these objects without bridging?

Type of Waste Dry waste is efficiently compacted by a stationary compactor. Wet waste is best handled by a self-contained, liquid-tight compactor.

Ease of Use Is the compactor conveniently located? What is the loading height? Does it save steps and labor? Is it easy to feed?

Is one central point adequate or should several locations be considered?

Available Space Is there space for the compactor and collection truck to service the compactor? Are overhead clearances adequate?

Suitable Voltage Is adequate power available? Three-phase? Single phase?

Collection Equipment Compatibility Is the compactor compatible with local waste collection equipment?

Installation Does installation require a thru-the-wall chute, a doghouse, or a dock-fed hopper? Is the compactor adaptable to these types of installations?

The amount by which a compactor will reduce the volume of solid waste

depends on several factors:• Type of refuse• Total force of compaction RAM• Type of compaction container

Example: You could expect to compact 160 loose cubic yards of mixed waste into one 40 cubic yard container.

The average compaction ratio for compactible, mixed waste is 4 to 1.

Considerations when choosing a compactor

COMPACTION RATIO

A compactor consists of 5 basic parts:

1. The Body is a steel structure which houses all the other parts. It has an area where material is compiled or CHARGE BOX with heavily reinforced sides to withstand the forces of compaction. A BREAKER BAR, made of a heavy steel angle, is located across the front of the charge box. This bar breaks oversized objects like wood or pallets before they enter the compaction container

2. The Ram is a specially designed steel structure with heavy face plate. It moves horizontally through the charge box, forcing the refuse into the compaction container.

Accu-Pak or Pack-ManWASTE TYPE: Primarily wet waste and food waste with a few dry applications

APPLICATIONS: Fast food, restaurants, nursing homes, small grocery stores

SIZES: 3, 4, 6 and 8 cubic yard units

5. The Electric Panel Box contains the transformer, motor starter, relays, fuses, and switches that operate the compactor. Most panel boxes incorporate printed circuit boards or programmable controllers for added reliability. All should be UL rated.

3. The Cylinder is attached behind the ram and moves it forward and backward. Inside the cylinder is a piston and rod which operates hydraulically. The cylinders vary in size. Larger ones are used in heavy- duty compactors with big charge

boxes. Cylinders are sized by bore and rod diameters.

4. The Power Unit consists of a hydraulic oil tank, pump, electric motor, and directional control valve. The oil, under high pressure, forces the piston in the cylinder to move forward and backward.

Exceptions to the 4 to 1 ratio:Industrial waste consisting mainly of pallets and heavy boxes might yield only a 2 to 1 compaction ratio. Climate affects compaction ratio (frozen garbage is more difficult to compact than wet garbage). Consider ALL variables before estimating the compaction ratio for a specific application.

WHO HOWNEEDS A

COMPACTOR?A COMPACTOR

WORKS?

Ratchet

Charge box

Breaker bar

Clear top opening

COMPACTION ADVANTAGES

TYPES OF COMPACTORSOperator Controls

Autodesk Vehicle Tracking v18.02.800(20171204) (c) Autodesk, Inc. www.Autodesk.com

Date:

Scale:1:250

Title:

FRONT END LOADER

Notes:

Turn(s) based upon a design speed of 2.50mph. After transition, inner wheels follow an arc of minimum radius 38.00ft. Curb is located 0.98ft from the vehicle. Maximum kick out distance is 0.566ft.

30°

60°

90°

120°

150°

18

0°

50.955ftMin Radius

(Outer Wheel)

38ftM

in R

adiu

s

(Inner W

heel) 5

4.6

12ftM

in R

adius

(Out

er Body)

35.109ft

Max Kickout 0.566ft

37

7.5 19.5 5

FRONT END LOADER

Overall Length 37.000ft

Overall Width 8.083ft

Overall Body Height 1.400ft

Min Body Ground Clearance 1.400ft

Track Width 8.000ft

Lock-to-lock time 4.00s

Curb to Curb Turning Radius 46.000ft