Cisco.Yesuse.648-385.v2013-04-18.by.yofe · 2019-10-17 · A host on the Sales subnet (10.0.2.0/24)...

648-385

Number: 000-000Passing Score: 800Time Limit: 120 minFile Version: 1.0

http://www.gratisexam.com/

www.Test-inexam.com

Exam A

QUESTION 1Which two statements best describe the wireless core feature set using autonomous access points whenimplementing Wireless Domain Services? (Choose two)

A. The primary Layer 2 WDS server address is configured via the infrastructure access point GUIB. The primary Layer 2 WDS server address is automatically discovered by the infrastructure access points

through multicastC. The primary Layer 2 WDS is selected by the highest MAC address,followed by priority numberD. The primary Layer 2 WDS is selected by the highest priority number,followed by MAC addressE. The primary Layer 2 WDS is selected by the highest IP address,followed by MAC address

Correct Answer: BDSection: (none)Explanation

Explanation/Reference:

QUESTION 2Which companion switch is recommended to be installed with Cisco Smart Business Communications System?

A. C2950B. C3750C. ESW 500D. SRW224G4

Correct Answer: CSection: (none)Explanation


QUESTION 3Refer to the exhibit.

A host on the Sales subnet (10.0.2.0/24) is not able to initiate a web connection to an outside website.According to the network diagram and partial Cisco Configuration Professional configuration shown in theexhibit. What is the cause of the problem?

A. The dynamic NAT global pool is not configured correctlyB. The source networks for static NAT are not configured correctlyC. The administrator has not added an access list to allow the collectionD. The source network for dynamic NAT is not configured correctly

Correct Answer: DSection: (none)Explanation


QUESTION 4In which of these phase is a customer's current networking structure assessed

A. planB. designC. implementD. prepare

Correct Answer: ASection: (none)Explanation


QUESTION 5What are two ways to secure traffic across a network? (Choose two)

A. Cisco ISR G2B. Identify-management devicesC. ACLsD. FirewallsE. VPN connectionF. VLANs

Correct Answer: CDSection: (none)Explanation


QUESTION 6You have just configured HSRP and need to determine which router is active. Which command should youenter?

A. Show ip hsrp activeB. Show standby activeC. Show standbyD. Show active



QUESTION 7What do radio-wave radiation patterns allow you to determine when you are implementing wireless networks?


A. Size of the coverage areaB. Which antenna is being usedC. Temperature of the coverage areaD. Shape of the coverage area



QUESTION 8Which command assigns a cost value of 17 to a switch port?

A. Spanning-tree interface fastethernet 5/8 17B. Spanning-tress portcost 17C. Spanning-tree port cost 17D. Spanning-tree cost 17}



QUESTION 9Which command displays the routing information that will be used to move data between VLANs on a router ona stick?

A. Router# show ip protocolsB. Router# show ip routeC. Router# show vlan[vlan_ID]D. Router# show vlan route

Correct Answer: BSection: (none)Explanation


QUESTION 10What were two primary design purpose for ISRs? (Choose two)

A. To provide a centralized threat database for IPS sensorsB. To bring IP technology,voice mail,email,and firewall services to the end userC. To implement and to integrate fully network services such as security,WAN routing,and Ethernet switchingD. To offer Fast Ethernet and 10 Gigabit Ethernet as a high-speed routing platformE. To be a next-generation,high-performance routing platformF. To provide all security-management functions in one high-performance device

Correct Answer: BCSection: (none)Explanation


QUESTION 11What are two areas in which PoE can be applied? (Choose two)

A. building managementB. data center managementC. retail video kiosksD. digital telephonyE. virtual networks

Correct Answer: ACSection: (none)Explanation


QUESTION 12Which identify credential is used most commonly to secure network data?

A. VPNB. PINC. ID cardD. Password



QUESTION 13You are troubleshooting OSPF neighbor establishment problems, which are occurring over Frame Relayinterfaces that use the default OSPF network type. What should you verify in the router configuration?

A. the ip ospf network point-to point statement under the Frame Relay interfaceB. the ip ospf priority statement on the Frame Relay interface on the designated routerC. the neighbor statements on the Frame Relay interfaceD. the frame-relay map statement on the Frame Relay interface



QUESTION 14What are two advantages of using an intermediate distribution frame? (Choose two)

A. Power over Ethernet capabilityB. higher RU densityC. reduced spaceD. hot-swappable hard drives

E. reduced cabling

Correct Answer: AESection: (none)Explanation



R2 is always in the init state. Which two statements are correct? (Choose two)

A. R2 is seeing hello packets from R1 B. R2 is not seeing hello packets from R1B. The exchange of data between R1 and R2 is occurring because each is sending hello packetsC. Two-way communication has not been established between R1 and R2 because R2 is not seeing its router

ID in the hello packets that it is receiving from R1D. R2 has an access list defined for S0 that is blocking an OSPF multicast IP address of 224.0.0.5

Correct Answer: ADSection: (none)Explanation


QUESTION 16Which type of antenna would be best used in a classroom environment?

A. omnidirectionalB. YagiC. patchD. parabolic



QUESTION 17Which steps must be taken when preparing Cisco ASDM for use?

A. connect the PC to the security,set up the security appliance,and use the console to connect to PIXB. Set up security appliance,connect to the security appliance,and configure the PC for DHCPC. Configure the PC,set up the security appliance,and ensure that the PC and security appliance are on the

same subnetD. Set up security appliance,connect the PC to the security appliance,and ensure that the PC is on the same

subnet as DHCP



QUESTION 18The Cisco SA 500 Series Security Appliances are built specifically for businesses with less than 100employees. What are three important benefits of this device? (Choose three)

A. business-grade firewallB. premium support via SMARTnetC. site-to-site VPN for remote officesD. Cisco IOS software-basedE. email securityF. XML support

Correct Answer: ACESection: (none)Explanation


QUESTION 19What are two advantages of implementing a router on a stick? (Choose two)

A. offers a single traffic path to alleviate congestionB. uses a common network topologyC. provides communications between VLANs on remote switchesD. allows multilayer switches to perform routingE. offers the highest rate of packets-per-second routing performanceF. allows for single point of failure for easy management and upgrade

Correct Answer: CFSection: (none)Explanation



A network administrator is troubleshooting an EIGRP connection between Router A and Router B, Given thedebug output on Router A, which two statements are true? (Choose two)

A. Router A received a hello packet with mismatched autonomous system numbersB. Router A received a hello packet with mismatching hello timersC. Router A received a hello packet with mismatched authentication parametersD. Router A received a hello packet with mismatched metric-calculation mechanismsE. Router A will form an adjacency with Router BF. Router A will not form an adjacency with Router B

Correct Answer: DFSection: (none)Explanation


QUESTION 21Which three are integrated Smart Applications included with the Cisco Unified Communications 500 series?(Choose three)

A. Smart Business SuiteB. Connected Data ProtectorC. Timecard ViewD. Cisco Unified CallConnectorE. Cisco WebEx PhoneConnectF. VoiceView Express

Correct Answer: CDESection: (none)Explanation


QUESTION 22What should you do first when selecting the appropriate antenna for a wireless deployment?

A. Determine the shape of the area to be coveredB. Determine the frequency of the radioC. Determine the location of the access pointD. Determine the direction of the coverage

Correct Answer: BSection: (none)

Explanation


QUESTION 23Which authentication uses biometrics?

A. passwordB. voiceC. tokensD. certificates



QUESTION 24What does understanding the radiation patterns of different antennas types help you to determine whenproviding wireless coverage in an office building?

A. the exact number of access points that are neededB. the type of antenna to cover a specific areaC. the size of an area that will be coveredD. the location of the access points



QUESTION 25Which combination of ports is available on the Cisco SPA 8800 voice gateway?

A. Onestation port and one trunk port (1xFXS and 1xFXO)B. Twostation ports (2xFXS)C. Fourstation ports and four trunk ports (4xFXS and 4xFXO)D. Eightstation ports (8xFXS)



QUESTION 26Which three elements can you review when examining the traffic across a network? (Choose three)

A. VPN connection

B. packet flowsC. ACLsD. statesE. connectionsF. firewallsG. mainframe

Correct Answer: BDESection: (none)Explanation


QUESTION 27How do the Cisco ISR G2 platforms enable the next phase of branch-office evolution?

A. They allow future enabling of high-bandwidth video and high-availability,through multi-core CPUs andsupport for high-capacity DSPs.

B. They integrate multiple processors in one unit to enable rich-media collaboration and virtualizationC. They feature wire-speed Fast Ethernet for high performanceD. They offer services through a robust Layer 2 and Layer 3 fixed and stackable switch



QUESTION 28What are two differences between medium and large campus network designs? (Choose two)

A. number of supported devicesB. types of supported devicesC. architectureD. scalabilityE. networking design



QUESTION 29Which security audit mode allows you to make all recommended security-related configuration changesautomatically?

A. Security Audit wizardB. interface managementC. One-step LockdownD. Cisco Configuration Professional



QUESTION 30After configuring VTP, you no longer receive updates as expected. Which command can you use to verify thenumber of VTP advertisements being transmitted?

A. show vtp databaseB. show vtp countersC. show vtp statisticsD. show vtp status



QUESTION 31Which design phase service component includes the development and documentation of the test case or casesused to verify that a deployed infrastructure meets operational, functional, and interface requirements?

A. Implementation PlanB. Business PlanC. Staging PlanD. Detailed Design DevelopmentE. Systems Acceptance Test Plan Development

Correct Answer: ESection: (none)Explanation


QUESTION 32Using Smart Designs increases the typical deal size by how much?

A. 2xB. 3xC. 5xD. 10x



QUESTION 33How many users are supported on the Cisco Unified Communications models 540 and 560 platforms?

A. 16 users on the UC540 and 64 users on the UC560B. 16 users on the UC540 and 104 users on the UC560C. 32 users on the UC540 and 64 users on the UC560D. 32 users on the UC540 and 104 users on the UC560



QUESTION 34Which two statements best describe the wireless core features set using autonomous access points whenimplementing repeater topology? (Choose two)

A. RF overlap between access points should be 10 to 15 percent with unique channels configuredB. RF overlap between primary and repeater access points should be 10 to 15 percent with the same channel

configuredC. RF overlap between primary and repeater access points should be 50 percent with the same channel

configuredD. RF overlap between primary and repeater access points should be 50 percent with unique channels

configuredE. Clients that are associated with the repeater access point will have 10 to 15 percent less data throughput

than clients that are associated with the primary root access pointF. Clients that are associated with the repeater access point will have 50 percent less data throughput than

clients that are associated with the primary root access point



QUESTION 35Which command would you use to run authorization for all commands at the specified privilege level(n)?

A. aaa authorization commandndefault group tacacs+localB. aaa authorization exec default group tacacs+localC. aaa authorization enable default group tacacs+enableD. aaa authorization group tacacs+local



QUESTION 36Which pre-sales SMART Design documents are available to help you implement and install a solution?(Choose three)

A. Quick Quoting ToolB. Small Business Product GuideC. Smart Business Communications SystemD. Solution ProfileE. Overview PresentationF. Cisco Configuration Assistant

Correct Answer: BDESection: (none)Explanation


QUESTION 37Which receiving antenna has high gain and requires accurate aim at the transmitting antenna?

A. omnidirectionalB. YagiC. parabolicD. patch



QUESTION 38What is the major difference between TACACS+ and RADIUS?

A. TACACS+ runs in TCP,RADIUS operates in UDPB. TACACS+ runs in UDP,RADIUS operates in TCPC. RADIUS encrypts the entire body of the access-request packet that is sent from the client to the

server,TACACS+ encrypts only the password in the access-request packetD. TACACS+ and RADIUS operate on two different protocol layers



QUESTION 39Which two WAN interfaces does the Cisco SRP 520 Series support? (Choose two)

A. Fibre ChannelB. ADSL2+C. senalD. Fast EthernetE. passive optical network (PON)



QUESTION 40Which three WAN technologies does the Cisco SR 500 Family support? (Choose three)

A. Fast EthernetB. Fibre ChannelC. ADSLD. T1E. IPv6F. SIP trunking

Correct Answer: ACDSection: (none)Explanation


QUESTION 41What can be used to troubleshoot complex network and VPN connectively issues?

A. NATB. CCPC. IPsecD. NAC



QUESTION 42Where might you go on the Cisco ASDM home page to review graph outputs?

A. ConfigurationB. RoutingC. MonitoringD. Home



QUESTION 43Which three types of ACL would you use to secure traffic on the network? (Choose three)

A. VLANB. reflexiveC. packetsD. dynamicE. IPSF. firewalls

Correct Answer: ABDSection: (none)Explanation


QUESTION 44Which two statements are correct about OSPF in a multiarea environment? (Choose two)

A. OSPF will be default summarize updates between areaB. OSPF requires the use of the area range configuration command only when nondefault summarization is

requiredC. OSPF ABR routers are needed only at the boundary of another OSPF areaD. OSPF uses wildcard masks in the network statements but subnet masks in the area range statementsE. OSPF requires that all areas have a least one ASBR



QUESTION 45OSPF routes are being redistributed into EIGRP but they are not showing up in the routing table. What are twopossible causes? (Choose two)

A. CEF has not been enabledB. Synchronization has been turned offC. Incorrect distribute lists have been configuredD. No default metric has been configured for EIGRPE. The ip classless command is missingF. There are mismatched autonomous system numbers



QUESTION 46You are configuring a VLAN and the switch you are using requires that you do so within the VLAN databases.Which command allows you to enter the VLAN databases?

A. Switch# vlan databaseB. Switch (config) # vlan databaseC. Switch (config-if) # vlan databaseD. Switch (vlan)# vlan database



QUESTION 47Which three statements are correct about the IEEE 802.3af Power over Ethernet standard? (Choose three) A. Itdefines a port that acts as a power source to be a PSE

A. It defies a powered device to be a PDEB. It defies how a powered device is detectedC. It defies three methods of delivering Power over Ethernet to the discovered powered deviceD. It describes five power classes to which a device may belongE. It defines power class 0 as being reserved for future use



QUESTION 48What is the primary purpose of SMB Smart Designs?

A. assists in locating appropriate resourcesB. provides validated commercial solutionsC. provides training on products,tools,and solutionsD. provides a direct support path for any partner issueE. provides a step-by-step outline of implementation tasks required



QUESTION 49Which of these is the best definition of the Cisco Lifecycle Services approach?

A. It defines the minimum set of services required to successfully deploy and operate a set of Ciscotechnologies

B. It determines how best to price Cisco productsC. It provides partners with a useful way to leverage Cisco resourcesD. It consists of these phase: plan,deploy,support,and troubleshoot



QUESTION 50How are lightweight access points different than autonomous access points?

A. Lightweight access points are managed individuallyB. Lightweight access points are B,G,N capableC. Lightweight access points require external antennasD. Lightweight access points require a WLAN controller



QUESTION 51Before installing Cisco ASDM, it is important to allow connectivity on the side interface of which device?

A. ISRB. WLCC. ASAD. Cisco Security MARS



QUESTION 52Which two are characteristics of HSSI cables? (Choose two)

A. HSSI cables use a female,10-pin,SCSI-II-type connectorB. The HSSI connector and the HSSI cable are identicalC. HSSI cables use cable CAB-HSI 1 and cable CAB-HNULD. The HSSI connector and the HSSI cable are similarE. The CAB-HUNL is used to connect your router to an external DSU



QUESTION 53Which statement best describes clustering in a small-business wireless network?

A. automatically configures wireless client devices via Wi-Fi Protected SetupB. can get real-time traffic or bandwidth statistics form an access point within a clusterC. replicates configuration parameters across access points in the cluster,while optimizing network

performanceD. allows multiple access points to be connected wirelessly,without the need for a wired Ethernet network



QUESTION 54What are two uses for USB ports on ISRs? (Choose two)

A. increased memory capabilitiesB. secure device authenticationC. bulk flash storageD. control over the types of files that can be storedE. digital certificate storage



QUESTION 55When troubleshooting poor network performance, which two symptoms would typically be associated with

a network layer problem? (Choose two)

A. Packet loss is more than 30 percentB. There is excessive broadcast trafficC. There are excessive CRC errorsD. Pings succeed only part of the timeE. Slips are detected on WAN interfacesF. ARP requests are timing out



QUESTION 56Which screen on the Cisco ASDM home page would you use to see which access list rules are in effect?

A. NATB. InterfacesC. Routing

D. Security Policy



QUESTION 57Which type of antenna is used when coverage in all directions is required?

A. directionalB. bidirectionalC. OmnidirectionalD. patch



QUESTION 58Which service should be disabled or filtered via a firewall because an attacker could use the service todownload a copy of Cisco IOS software from a router (thereby making the router vulnerable to DOC attacks)?

A. PAD serviceB. finger serviceC. TCP/UDPD. BOOTP



QUESTION 59Which two statement best describe the wireless core feature set using autonomous access points whenimplementing Wireless Domain Services? (Choose two)

A. Layer 2 and Layer 3 services can be configured in a Cisco Aironet autonomous AP or a Cisco IntegratedServices Router

B. Layer 2 services can be configured in a Cisco Aironet autonomous AP or a Cisco Integrated ServicesRouter

C. Layer 2 and Layer 3 services can be configured in a Cisco Aironet autonomous AP or controllersD. Layer 3 services can be configured in WLSME. Layer 3 services can be configured in WLSE




Switches A and C are running PVST+ STP, and switch B is running 802.1Q STP, if the BPDU of the root inVLAN 1 is better than the BPDU of the root in VLAN 2, then there is no blocking port in the VLAN 2 topology.The BPDU of VLAN 2 never makes a full circle around the topology, it is replaced by the VLAN 1 BPDU on theB_C link, because B runs only one STP merged with VLAN ! STP of PVST+ Thus, there is a forwarding loopWhat does PVST+ do to correct this?

A. Switch A sends PVST+BPDUs of VLAN 2 (to the SSTP address that is flooded by switch B) towards SwitchC. Switch C will put port C-B into a type-inconsistent,which prevents the loop

B. Switch B sends PVST+BPDUs of VLAN 1 (to the SSTP address that is flooded by switch A) towards SwitchC. Switch C will put port C-B into a type-inconsistent,which prevents the loop

C. Switch C sends PVST+BPDUs of VLAN 2 (to the SSTP address that is flooded by switch B) towards SwitchC. Switch C will put port C-B into a type-inconsistent,which prevents the loop

D. Switch A sends PVST+BPDUs of VLAN 1 (to the SSTP address that is flooded by switch B) towards SwitchB. Switch A will put port C-B into a type-inconsistent,which prevents the loop



QUESTION 61What is used to prevent outside resources from accessing private information within the company?

A. IPsecB. VPNC. PIND. Firewalls



QUESTION 62Which type of security allows visibility into the state of the operating system and is the only way to inspectencrypted traffic?

A. zero updated architectureB. network-based securityC. endpoint-based securityD. ACLs



QUESTION 63Which two benefits will a client see from adding a Wireless LAN Controller to their Smart BusinessCommunications System? (Choose two)

A. allow for guest accessB. increase connection speedsC. add additional access pointsD. network management with CLI



QUESTION 64To avoid carrying every length of cable, lighting arrestors, and splitters when performing site surveys, engineerscan outfit their survey kits with which item?

A. Category 5 cable

B. RP-TNC plugC. antenna attenuatorD. RP-TNC connector



QUESTION 65Which two are components of AAA? (Choose two)

A. access control listsB. Cisco IOS SoftwareC. Cisco Secure Access Control ServerD. Security Audit wizardE. network access server

Correct Answer: CESection: (none)Explanation


QUESTION 66Which three business requirements development activities are performed in the prepare phase before creatinga technology strategy? (Choose three)

A. identifying and assessing customer business requirementsB. documenting and categorizing customer business requirements in terms of

performance,availability,capacity,and securityC. producing a documented technology strategyD. creating a bill of materialsE. presenting documented business requirements to a customer and having the customer validate themF. completing a site survey

Correct Answer: ABESection: (none)Explanation


QUESTION 67Which post-sales SMART Design documents are available to help you better serve your customers? (Choosethree)

A. Design GuideB. Small Business Product GuideC. Implementation GuideD. Solution Profile

E. Cisco Configuration AssistantF. Application Notes

Correct Answer: ACFSection: (none)Explanation


QUESTION 68Which type of VPN is deal for employees who use a home PC or public computer to access the network?

A. IP secremoteaccess VPNB. mobile VPNC. dialupoffload VPND. SSL VPNE. GET VPN



QUESTION 69Which benefit can be obtained by using the change management service component in the operate phase?

A. reduced operating costs,due to consistent framework for making necessary changes in an efficient andaccountable manner

B. greater accuracy,completeness,and timeliness of network configuration informationC. notification provided to interested parties regarding problems that have been identified,and a system that

scales with customer requirementsD. improved system service quality and fewer disruptions




The tables contain information from the Cisco Configuration Professional configurations of Router A and RouterB, Traffic between Host 1 and Host 2 is not successfully establishing the site-to-site VPN between Router A andRouter B.What is the mostly likely cause of this fault?

A. Router A is using a standard IP ACL (100-149) while Router B is using a Turbo ACL (150199)B. The IKE encryption methods on the two routers are differentC. The IPSec policy map names on the two routers are differentD. The IPSec rules on the two routers are not permitting the correct interesting traffic



QUESTION 71Which of the following best describe the customer benefits of change management in the operate phase?

A. reduce unnecessary disruption,delays,rework,and other problems by establishing test cases for use inverifying that the system meets operational,functional,and interface requirements

B. improve its ability to make sound financial decisions by developing a business case based on its businessrequirements and establishing a basis for developing a technology strategy

C. reduce operating costs and limitchange relatedincidents by providing a consistent and efficient set ofprocesses

D. improve the return on investment and hasten migration by identifying and planning for necessaryinfrastructure changes and resource additions,as well as reduce deployment costs by analyzing gaps earlyin the planning process to determine what is needed to support the system



QUESTION 72Which of these is the best definition of the Cisco Lifecycle Services approach?

A. It defines the minimum set of services required to successfully deploy and operate a set of Ciscotechnologies.

B. It determines how best to price Cisco products.C. It provides partners with a useful way to leverage Cisco resources.D. It consists of these phases: plan,deploy,support,and troubleshoot.



QUESTION 73What two types of telephony interfaces are used for PSTN connectivity? (Choose two.)

A. DigitalB. OpticalC. AnalogD. CDMA



QUESTION 74Which statement correctly describes the keys witch model of deployment for call processing?

A. All IP Phones are able to answer any incoming PSTN call on any lineB. PSTN calls are routed through a receptionist or automated attendant.C. All IP Phones in the system have a single unique extension number.



QUESTION 75Which definition best describes the implementation service component within the implement phase?

A. providing a step-by-step plan that details the installation andservice commissiontasks required in order tocreate acontrolled implementationenvironment that emulates a customer network

B. assessing the ability of site facilities to accommodate proposed infrastructure changesC. developing and executingproof-of-concept tests,validating high-level infrastructure design,and identifying

any design enhancementsD. Installing,configuring and integrating systems components based on an implementation plan developed in

earlier phasesE. improving a customer's infrastructure security system



QUESTION 76A customer with a small enterprise network of 15 remote sites is trying to optimize its VPN by migrating someremote sites using Frame Relay connections to the Internet to using cable connections to the Internet.Minimizing costs is one of the customer's highest priorities. Only a moderate amount of IP traffic is passingthrough the network, most of which is from the remote sites to the central site. IPSec should be used to provideVPN functionality and basic confidentiality is desired. Based on the traffic patterns, which topology would be theeasiest for this customer to set up and manage?

A. full meshB. partial meshC. point-to-multipointD. huband spoke



QUESTION 77How can the proper configuration of Voice Mail be tested at an end user's IP phone?

A. Press the "i" button.B. Press the "Settings" button.C. Press the "Services" button.D. Press the "Messages" button



QUESTION 78In what location is it recommended that the Cisco Catalyst 6500 Series WLSM be placed?

A. distribution layerB. core layerC. access layerD. network management functional module



QUESTION 79Which of these is an accurate list of Cisco Lifecycle Services phases?

A. initiation,planning,analysis,design,development,implementation,operations and maintenanceB. project planning,site assessment,risk assessment,solution selection and acquisition,testing,and operationsC. Prepare,plan design implement operate,and optimizeD. analysis,design,deployment,testing,implementation,and production IE. presales,project planning,development,implementation,operations testing,and operations sign-off



QUESTION 80What port role assignment would you make for the Gigabit Ethernet port on the Cisco CE520 used in the SmartBusiness Communications System?

A. IP Phone and desktopB. Cisco UC520C. Cisco CE520D. Cisco 871W



QUESTION 81This item consists of one or more multiple choice type questions that you must answer. To answer thesequestions, you need to use a GUI tool that becomes fully accessible by the use of the labs you see below thesedirections. The tabs have up and down arrows to signal the direction that the tabbed window may be dragged loexpose or hide the GUI tool. When you are done using the GUI tool, you may drag the tab

down to continue answering questions. To advance to the next question in the series, click on the numberedbutton to the left of each question. Make sure that you have answered all the questions before continuing to thenext item.

Which method list and method is used to authenticate the remote access VPN users? (Choose two.)

A. sdm_vpn_xauth_ml_1B. sdm_ypn_group_ml_1C. SDM_CMAP_1D. local database on the ISRE. remote TACACS+ serverF. remote Radius Server



QUESTION 82Refer to the exhibit. Switches A and C are running PVST+ STP, and Switch B is running 802.10 STP. If theBPDU of the root in VLAN 1 is better than the BPDU of the root in VLAN 2, then there is no blocking port in theVLAN topology. The BPDU of VLAN 2 never makes a "full circle" around the topology; it is replaced by theVLAN 1 BPDU on the B. C link, because B runs only one STP merged with VLAN 1 STP of PVST+.Thus, there is a forwardin loop.What does PVST+ do to answer this?

A. Switch A sends PVST+ BPDUs of VLAN 2 (to the SSTP address that is flooded by Switch B) towardsSwitch C. Switch C will put port C.B into atype inconsistentstate,which prevents the loop.

B. Switch B sends PVST+ BPDUs of VLAN 1 (to the SSTP address that is flooded by Switch A) towardsSwitch C. Switch C will put port C.B into atype inconsistentstate,which prevents the loop.

C. Switch C sends PVST+ BPDUs of VLAN 2 (to the SSTP address that is flooded by Switch B) towardsSwitch C. Switch A will put port C.B into atype inconsistentstate,which prevents the loop.

D. Switch A sends PVST+ BPDUs of VLAN 1 (to the SSTP address that is flooded by Switch B) towardsSwitch B. Switch A will put port C.B into atype inconsistentstate,which prevents the loop.



QUESTION 83Which interface on the Cisco UC520 is assigned an IP address either statically or through DHCP?

A. WAN interfaceB. LAN interfaceC. Switch portD. PSTN Interface



QUESTION 84Which benefit can be obtained by using the change management service component in the operate phase?

A. Reduced operating costs due to a consistent framework for making necessary changes in an efficient andaccountable manner

B. Greater accuracy,completeness,and timeliness of network configuration informationC. Notification provided to interested parties regarding problems that have been identified,and a system that

scales with customer requirementsD. Improved system service quality and fewer disruptions



QUESTION 85What are two ways to test the LAN connectivity on the Cisco CE520? (Choose two.)

A. Ping the IP address of the Cisco-Data Access VLAN from the Cisco UC520 console.B. Ping the IP address of the Cisco-Data VLAN from a device attached to the Cisco CE520C. Ping default gateway from the Cisco UC520.D. Ping the IP address of the Cisco-voice VLAN from a device attached to the Cisco CE520.E. Ping default gateway from the Cisco CE520.F. Ping the IP address of the Cisco-Distribution VLAN from the Cisco UC520 console.



QUESTION 86Which statement correctly describes configuration of the VPN server?

A. It requires definition of a Group ID for remote clients.B. It requires configuration of port settings for the VPN server on the Cisco UC520.C. It uses a preshared Key for remote device authenticationD. The WAN interface is preselected.



QUESTION 87In a new Cisco UC520 installation, when must IP routing be configured?

A. When the service provider assigns static IP informationB. When the service provider assigns dynamic IP information.

C. When analog PSTN trunks are used.D. When digital PSTN trunks are used.



QUESTION 88Which two benefits will a client see from adding a Wireless LAN Controller to their Smart BusinessCommunications System? (Choose two).

A. allow for guest accessB. increase connection speedsC. add additional access pointsD. network management with CLI



QUESTION 89Which critical issue should you account for when implementing an integrated network security managementdesign?

A. NAT interoperates with encrypted voice trafficB. host-based intrusion detection systems reside in the networkC. All network devices are timesynchronizedD. SNMP community read-write strings are configured to allow for total management access



QUESTION 90In which of these phases is a customer's current network infrastructure assessed?

A. PlanB. DesignC. ImplementD. Prepare



QUESTION 91To save time during rediscovery, which three types of device information does Cisco Configuration Assistantretain? (Choose three.)

A. IP Address


B. MAC AddressC. Host NameD. Communication ProtocolE. Port SettingsF. Topology

Correct Answer: ACDSection: (none)Explanation


QUESTION 92Which dial plan scenario may require PSTN trunks for outbound calls?

A. All the employees,the auto attendant or receptionist,and thevoicemail system nave direct inward dialnumbers using analog trunks.

B. A subset of the employees,the auto attendant or receptionist,and thevoicemail system have direct inwarddial numbers,and the remaining employees do not have direct inward dial numbers.

C. All the employees,the auto attendant or receptionist,and thevoicemail system have direct inward dialnumbers using digital interfaces.



QUESTION 93What are two configurable options for Call Control on the Cisco UC520? (Choose two.)

A. Shared KeyB. PBXC. Key SystemD. EncryptionE. Call Waiting

Correct Answer: BC

Section: (none)Explanation


QUESTION 94Refer to the Exhibit. According to Cisco VPN Client Software output Shown, Which two Statement are correctabout the connection entry named isr? (Choose Two)

A. HMAC.SHA1 is used to authenticate the remote users.B. Preshared key is used to authenticate the remote peerC. AES is used to provide data confidentiality.D. The Cisco VPN Client software is assigned an internal IP address of 192.168.1.1.E. The PC that is running the Cisco vpn Client software win not have access to the local LAN once the PC is

connected into the VPN

Correct Answer: BESection: (none)Explanation


QUESTION 95Refer to the exhibit. According to the Cisco Adaptive Security Device Manager window, which statement aboutaddress translation is correct?

A. Using Network Address Translation,any host on the DMZ1 subnet (172.16.1.0) will be translated to amapped address on the outside interface of 192.168.1.11. I

B. Using port address translation,DMZ2 host 172.16.10.2 will be translated on DMZ1 to IP address172.16.1.22 with a dynamically assigned port address.

C. Using Network Address Translation host 10.0 1.10 on the inside network will be dynamically translated to amapped address from the address pool of 192.168.1.20 to 192.168.1.94.

D. Using port address translation,outside host 192.168.1.10 with a dynamically assigned port address will betranslated to 10.0.1.11 on the inside interface.



QUESTION 96Which two are benefits of installing Cisco Monitor Director at an SMB site for the partner selling the solution?(Choose two.)

A. simplifies Smart Business Communications System installationB. allows the end customer to get free software updates

C. monthly recurring revenue modeD. automated monthly reporting on system performance



QUESTION 97Which Cisco Catalyst Express 520 feature optimizes quality of service?

A. Cisco Configuration AssistantB. Cisco Smart portsC. Cisco Network Admission ControlD. Cisco Smart Assist



QUESTION 98Which three business requirements development activities are performed in the prepare phase before creatinga technology strategy? (Choose three.)

A. Identifying and assessing customer business requirementsB. Documenting and categorizing customer business requirements in terms of

performance,availability,capacity and securityC. Producing a documented technology strategyD. Creating a bill of materialsE. Present documentedbusiness requirements to a customer and having the customer validate themF. Completing a site survey

Correct Answer: ABESection: (none)Explanation


QUESTION 99Refer to the exhibit. This display has been truncated to remove information that is not relevant to the question.What would be a reason that there have been 21 ignored packets?

A. Ethernet0has no CDP neighbors.

B. There are no free input buffers to accept new packetsC. There are no free output buffers for packets,which are traversing the router,to go into for transmission.D. Ethernet0and the neighbor that it is connected to are not running the same routing protocol.E. This is not a valid error display. The display has been modified to show that there have been ignored

packets.



QUESTION 100After configuring VTP, you no longer receive updates as expected. Which command can you use to verify thenumber of VTP advertisements being transmitted?

A. show vtp databaseB. show vtp countersC. show vtp statisticsD. show vtp status



QUESTION 101You enter the command show ip ospf neighbor and see "two-way/DROTHER" listed as the state for neighbor10.1.1.1.

What does this status indicate?

A. The neighbor 10.1 1 1 is not a DR or BDRB. The neighbor relationship with 10.1.1.1 has not yet completed.C. DR and BDR election is in progress.D. The neighbor 10.1.1.1 is the BDR.



QUESTION 102Which design phase service component includes the development and documentation of the test case or casesused to verify that a deployed infrastructure meets operational, functional, and interface requirements?

A. Implementation Plan.B. Business PlanC. Staging PlanD. Detailed Design Development

E. Systems Acceptance Test Plan Development



QUESTION 103Which implement phase service component consists of explaining the benefits and limitations of purchasedsupport options to a customer and ensuring that the customer understands operational processes andresponsibilities?

A. Staging and System MigrationB. Post Implementation Support Handoff MeetingC. Detailed Design DevelopmentD. Staff Training



QUESTION 104In which of these phases is a customer's network assessed to determine its system readiness?

A. PlanB. DesignC. OperateD. Implement



QUESTION 105How many voice expansion slots are provided by the Cisco UC520?

A. OneB. twoC. threeD. four



QUESTION 106A concern has been expressed that the switched infrastructure in an integrated network is vulnerable to VLANhopping attacks. Which two configuration statements can be used to mitigate VLAN hopping? (Choose two.)

A. switch port port-securityB. switch port port-security taggingC. switch port access vlanD. switch port doublE.tag snoopingE. switch port mode access

Correct Answer: CESection: (none)Explanation


QUESTION 107Which network management tool is designed to allow businesses to manage up to 40 devices?

A. Cisco Works UnrestrictedB. Cisco Works SNMSC. Campus ManagerD. Resource Management Essentials



QUESTION 108You are troubleshooting OSPF neighbor establishment problems, which are occurring over Frame Relayinterfaces that use the default OSPF network type. What should you verify in the router configuration?

A. the ip ospf network point-to-point statement under the Frame Relay interfaceB. The ip ospf priority 0 statement on the Frame Relay interface on the designated routerC. The neighbor statements on the Frame Relay interfaceD. Theframe relaymap statement on the Frame Relay interface



QUESTION 109You are configuring a VLAN and the switch you are using requires that you do so within the VLAN database.Which command allows you to enter the VLAN database?

A. Switch# vlan databaseB. Switch (config)# vlan databaseC. Switch (config-if)# vlan database

D. Switch (vlan)# vlan database



QUESTION 110Which two statements best describe the wireless core feature set using autonomous access points whenimplementing repeater topology? (Choose two.)

A. RF overlap between access points should be 10 to 15 percent with unique channels configured.B. RF overlap between primary and repeater access points should be 10 to 15 percent with the same channel

configured.C. RF overlap between primary and repeater access points should be 50 percent with the same channel

configuredD. RF overlap between primary and repeater access points should be 50 percent with unique channels

configured.E. Clients that are associated with the repeater access point will have 10 to 15 percent less data throughput

than clients that are associated with the primary root access point.F. Clients that are associated with the repeater access point will have 50 percent less data throughput than

clients that are associated with the primary root access point



QUESTION 111Refer to the exhibit. The Cisco Aironet 802.1 la/b/g Wireless LAN Client Adapter has two LEDs. Which two LEDstates indicate that the card is associated to an access point and is working properly? (Choose two.)

A. green LED off; amber LED solidB. green LED off; amber LED blinking sporadicallyC. green LED blinking quickly: amber LED blinking quickly

D. green LED blinking slowly,amber LED blinking slowlyE. green LED blinking slowly; amber LED blinking quickly



QUESTION 112Refer to the exhibit. The tables contain information from the Cisco Router and Security Device Managerconfiguration of Router A and Router B. Traffic between Host 1 and Host 2 is not successfully establishing thesite to-site VPN between Router A and Router B. What is the mostly likely cause of this fault?

A. The IPSec and IKE encryption methods do not match. They all have to be either 3DES or AES.B. Router A is using a standard IP ACL (100-149) while Router B is using a turbo ACL (150-199).C. The D.H Group settings on the two routers are set to group 2. They must be set to group 1 for SHA.1.D. The IPSec policy map names on the two routers do not match. They must be the same on both routers.E. The IPSec rules on the two routers are not permitting the Answer: interesting traffic



QUESTION 113

OSPF routes are being redistributed into EIGRP but they are not showing up in the routing table. What are twopossible causes? (Choose two.)

A. CEF has not been enabled.B. Synchronization has been turned off.C. incorrect distribute lists have been configuredD. No default metric has been configured for EIGRPE. The ip classless command is missing.F. There are mismatched autonomous system numbers.



QUESTION 114Which two statements best describe the wireless implementation of Cisco Aironet root and non-root bridging?(Choose two.)

A. Point-to-point access points can be used if one is root and the other is non-root.B. WGB can be used with an access point if the distance is less than one mileC. Root mode must be enabled only on one side in a point-to-point link to intemperate with other vendors and

comply with 802.11D. Up to 17 non-root bridges can associate to a root bridgeE. Point-to-point WGB can be used if total number of PCs is fewer than eight. The neighbor 10.1.1.1 is the

BDR



QUESTION 115Refer to the exhibit. Which two statements are answers about what is displayed? (Choose two.)

A. The IP address that is used for the router ID must be reachable.

B. Router 1 is the designated router because it has the lowest configured IP address.C. Router 1 is me designated router because it has the lowest configured loop back addressD. If Router 1 had a Pr1 off 0; it could not be designated router or a backup designated routerE. Router 1 has had its ID manually configured by using the router-ID command.



QUESTION 116The customer wants to implement wireless security through implementation of WPAv2. Which component ofWPAv2 would limit the rollout because of the continued use of old access points?

A. 48-bit IVB. AESC. TKIPD. MIC



QUESTION 117A company needs to provide site to-site VPN, remote access VPN, and firewall protection. Which device bestsupports all three functions?

A. Cisco PIXB. Cisco ASAC. Cisco ConcentratorD. Cisco Router and Security Device Manager



QUESTION 118Which two statements are answers about using Cisco Router and Security Device Manager (SDM) to configurethe OSPF routing protocol? (Choose two.)

A. Cisco SDM enforces the creation of area 0 when configuring OSPF.B. Cisco SDM will use the supplied wildcard mask to exclude the host bits from the configured network

addressC. Cisco SDM allows the configuration of an area range to allow route summarization between OSPF areas.D. Cisco SDM allows the selection of OSPFv1or 0SPFv2.E. Cisco SDM allows the configuration of passive interfaces




R2 is always in the init state. Which two statements are correct? (Choose two.)

A. R2 is seeing hello packets from R1.B. R2 is not seeing hello packets from R1.C. The exchanging of data between R1 and R2 is occurring because each is sending hello packets.D. Two-way communication has not been established between R1 and R2 because R2 is not seeing its router

ID in the hello packets that it is receiving from R1E. R2 has an access list defined for SO that is blocking an OSPF multicast IP address of 224.0.0.5.



QUESTION 120Which two features are only supported when using the Cisco Router and Security Device Manager (SDM)Advanced Firewall wizard and not supported when using the Cisco SDM Basic Firewall wizard? (Choose two.)

A. deep-packet inspectionsB. IP unicast Reverse Path Forwarding on the outside (untrusted) interfaceC. DMZ servicesD. Custom inspection rulesE. proxy authentication



QUESTION 121When troubleshooting poor network performance, which two symptoms would typically be associated with anetwork layer problem? (Choose two.)

A. Packet loss is more than 30 percentB. There is excessive broadcast traffic.C. There are excessive CRC errors.D. Pings succeed only part of the timeE. Slips are detected on WAN interfaces.F. ARP requests are timing out.



QUESTION 122Which command can be used to verify that RIPv2 is running on a router?

A. Show startup-configB. Show ip routeC. Show ip route ripD. Show ip protocols



QUESTION 123Which two statements best describe the wireless core feature set using autonomous access points whenimplementing Wireless Domain Services? (Choose two.)

A. Layer 2 and Layer 3 services can be configured in a Cisco Aironet autonomous AP or a Cisco IntegratedServices Router.

B. Layer 2 services can be configured in a Cisco Aironet autonomous AP or a Cisco Integrated ServicesRouter

C. Layer 2 and Layer 3 services can be configured in a Cisco Aironet autonomous AP or controllers.D. Layer 3 services can be configured in WLSM.E. Layer 3 services can be configured in WLSE.



QUESTION 124You have just configured and enabled the Cisco IOS Firewall feature set from a remote location using the CiscoRouter and Security Device Manager (SDM) Firewall wizard. You later want to double check your configurationusing Cisco SDM. However, you find that you can no longer connect to the Cisco IOS Firewall using CiscoSDM.What is the probable cause of this failure?

A. You must additionally specify the Cisco SDM management port number to gain access when theconfiguration has been applied.

B. You have not generated an RSA key pair between the host and device to allow secure access via CiscoSDM.

C. You have been locked out via access lists mat nave been applied to the router as a result of your CiscoSDM configuration.

D. You must specify the host IP address of Cisco SDM in the Configuration panel for allowed managementconnections.



QUESTION 125An 802.11 b telephone is receiving an audio signal from an access point, but cannot send audio.What is a possible cause?

A. the RSSI value on the telephone is greater than 35.B. The access point is set to receive only at 802.11g data rates.C. The security settings in the telephone do not match the settings in the access point.D. The transmit power in the telephone is significantly lower than the transmit power in the access point.



QUESTION 126Refer to the exhibit. A host on the Sales subnet (10.0.2.0/24) is not able to initiate a web connection to anoutside website. According to the network diagram and partial Cisco Adaptive Security Device Managerconfiguration shown in the exhibit, what is the cause of the problem?

A. The dynamic NAT global pool is not configured correctly.B. The source networks for static NAT are not configured correctly.C. The administrator has not added an access list to allow the connection.D. The source network for dynamic NAT is not configured correctly



QUESTION 127Users logging into Cisco Router and Security Device Manager should be authenticated using the Cisco ISRlocal user database. Currently, none of the users can access Cisco Router and Security Device Manager viaHTTP. You should check the configuration of which command or commands when attempting to resolve thisproblem?

A. There is no ip http secure-serverB. There is ip http authentication localC. There is line vty 0 5 login localD. There is aaa new-model

Correct Answer: B



QUESTION 128When using Cisco Router and Security Device Manager to configure AAA login authentication policies, whichfour methods are available? (Choose four.)

A. group RADIUS: use a list of RADIUS hostsB. group TACACS+ use a list of TACACS+ hostsC. enable: use enable passwordD. otp: useone timepasswordE. local use local databaseF. default: use line password

Correct Answer: ABCESection: (none)Explanation


QUESTION 129Which two statements are answers about OSPF in a multiarea environment? (Choose two.)

A. OSPF will by default summarize routing updates between areas.B. OSPF requires the use of the area range configuration command only when non default summarization is

required.C. OSPF ABR routers are needed only at the boundary of another OSPF areaD. OSPF uses wildcard masks in the network statements but subnet masks in the area range statement.E. OSPF requires that all areas have a least one ASBR.



QUESTION 130You have just configured HSRP and need to determine which router is active. Which command should youenter?

A. show ip hsrp activeB. show standby activeC. show starD. show active



QUESTION 131A North American customer is using 2.4-GHz radios in a point-to-point configuration. The radio power level is17 dBm and is transmitting at 11 Mbps. The customer is using 21.5-dBi dish antennas and 50 feet

of cabling, with a loss of 8.4 dB per 100 feet. The customer increased the distance between the transmitterstations and began experiencing link problems. Without using a professional installer, which step should thecustomer take to fix the situation?

A. Use a cable with a lower loss.B. Upgrade to an 802.11a radio.C. Install a higher gain antenna.D. Increase the transmitter power.



QUESTION 132Which three statements are answers about the IEEE 802.3af Power over Ethernet standard? (Choose three.)

A. It defines a port that acts as a power source to be a PSE.B. It defines a powered device to be a PDE.C. It defines how a powered device is detected.D. It defines three methods of delivering Power over Ethernet to the discovered powered device.E. It describes five power classes to which a device may belongF. It defines power class 0 as being reserved for future use.



QUESTION 133A user is unable to connect to the Cisco Router and Security Device Manager via HTTPS. Which two of thesemight have caused this problem? (Choose two.)

A. The ip https server command is missing from the running configuration.B. The ip httpsecure servercommand is missing from the running configurationC. The user is trying to launch Cisco Router and Security Device Manager from the inside (secured) interface

with a firewall enabled.D. The user has a privilege level lower than 15.E. The browser security level is set too high.



QUESTION 134Which two statements best describe the wireless core feature set using autonomous access points whenimplementing Wireless Domain Services? (Choose two.)

A. The primary Layer 2 WDS server address is configured via the infrastructure access point GUI.B. The primary Layer 2 WDS server address is automatically discovered by the infrastructure access points

through multicastC. The primary Layer 2 WDS is selected by the highest MAC address,followed by priority number.D. The primary Layer 2 WDS is selected by the highest priority number followed by MAC address.E. The primary Layer 2 WDS is selected by the highest IP address,followed by MAC address.



QUESTION 135Refer to the exhibit. A network administrator is troubleshooting an EIGRP connection between Router A

and Router B. Given the debug output on Router A, which two statements are true? (Choose two.)

A. Router A received a hello packet with mismatched autonomous system numbers.B. Router A received a hello packet with mismatched hello timers.C. Router A received a hello packet with mismatched authentication parameters.D. Router A received a hello packet with mismatchedmetric calculationmechanismsE. Router A will form an adjacency with Router B.F. Router A will not form an adjacency with Router B

Correct Answer: DFSection: (none)Explanation


QUESTION 136Which command assigns a cost value of "17" to a switch port?

A. spanning-tree interface fastethernet 5/8 17B. spanning-tree portcost 17C. spanning-tree portcost 17D. spanning-tree vlan 1 cost 17

Correct Answer: D



QUESTION 137You have configured and applied a Cisco IOS Firewall access rule to the inbound, untrusted interface. Yoususpect that the rule may be blocking necessary traffic onto the network. What must you do to delete that rulewhen using Cisco Router and Security Device Manager?

A. Select ACL Editor > Access Rules to delete the rule.B. You must remove the association between the rule and the interface before deleting the ruleC. You must delete the associated access list on the interface,then reconfigure the access list as required,and

then reapply the access group to the proper interface.D. Go to the Edit Firewall Policy tab to delete the rule.



QUESTION 138A customer in Europe needs to establish an 11-Mbps wireless bridge link between two office buildings that areapproximately 1.3 km apart. The wireless link will pass through a public park, which contains a lake that issurrounded by trees. You run the range calculation and determine that the Cisco Aironet 1300 Series OutdoorAccess Point/Bridge should work. You install the link using 10.5-dB yogis with 75 feet of standard Cisco cablingand both radios set at 20 mW. The wireless bridges are not able to establish or maintain a link.What is needed to successfully complete this link?

A. An amplifier needs to be installed at one of the sites.B. The antenna must be raised high enough to clear the treesC. Lower loss cabling needs to be used to bring the EIRP into legal limits.D. Due to the trees,a 21-dBi dish needs to be used for its narrower beam width.



QUESTION 139You connect via Telnet to a Cisco access point and enter the command show dot11 link test.Which output might you obtain?

A. signal-to-noise ratioB. incoming and outgoing signal strengthC. TX packets droppedD. RX packets per second




The tables contain information from the Cisco Router and Security Device Manager configurations of Router Aand Router B. Traffic between Host 1 and Host 2 is not successfully establishing the site-to-site VPN betweenRouter A and Router B.What is the mostly likely cause of this fault?

A. Router A is using a standard IP ACL (100-149) while Router B is using a Turbo ACL (150-199).B. The IKE encryption methods on the two routers are different.C. the IPSec policy map names on the two routers are different.D. the IPSec rules on the two routers are not permitting the Answer: interesting traffic.



QUESTION 141This item consists of one or more multiple choice type questions that you must answer. To answer thesequestions, you need to use a GUI tool that becomes fully accessible by the use of the labs you see below thesedirections. The tabs have up and down arrows to signal the direction that the tabbed window may be dragged loexpose or hide the GUI tool. When you are done using the GUI tool, you may drag the tab down to continue

answering questions. To advance to the next question in the series, click on the numbered button to the left ofeach question. Make sure that you have answered all the questions before continuing to the next item.

How many active VPN clients are currently connected to the 1841 ISR router?

A. 0B. 1C. 2D. 3E. 4F. 5



QUESTION 142This item consists of one or more multiple choice type questions that you must answer. To answer thesequestions, you need to use a GUI tool that becomes fully accessible by the use of the labs you see below thesedirections. The tabs have up and down arrows to signal the direction that the tabbed window may be dragged loexpose or hide the GUI tool. When you are done using the GUI tool, you may drag the tab down to continueanswering questions. To advance to the next question in the series, click on the numbered button to the left ofeach question. Make sure that you have answered all the questions before continuing to the next item.

Which IP address or address range will be used when allocating an internal IP address to the VPN clients forthe "test" VPN group?

A. 10.1.1.100 to 10.1.1.200 IB. 10.1-1.2 to 10.1.1.254C. 192.168.1.1 to 192.168.1.100D. 192.168.1.2 to 192.168.1.254E. 192.168.1.1F. 192.168.1.2



QUESTION 143This item consists of one or more multiple choice type questions that you must answer. To answer thesequestions, you need to use a GUI tool that becomes fully accessible by the use of the labs you see below thesedirections. The tabs have up and down arrows to signal the direction that the tabbed window may be dragged loexpose or hide the GUI tool. When you are done using the GUI tool, you may drag the tab down to continueanswering questions. To advance to the next question in the series, click on the numbered button to the left ofeach question. Make sure that you have answered all the questions before continuing to the next item.

Which authentication method is used by the test" VPN group?

A. RSA EncryptedNonceB. RSA Digital SignatureC. PresharedKeyD. Digital CertificateE. DH2



QUESTION 144You are the network consultant. You have a customer with a small network of 15 remote sites is trying tooptimize its VPN by migrating some remote sites using Frame Relay connections to the Internet to using cableconnections to the Internet. The key point for your customer is to save money. Only a moderate amount of IPtraffic is passing through the network, most of which is from the remote sites to the central site. IPSec shouldbe used to provide VPN functionality and basic confidentiality is desired, considering the above requirements.Which solution would be the easiest for this customer to set up and manage?

A. point-to-pointB. partial meshC. point-to-multipointD. hub-and-spoke



QUESTION 145In an infrastructure based on a wireless advanced feature set using lightweight access points, by which methodis a rogue contained?

A. The WCS sends excessive traffic to the rogue . thus overloading the access point.B. The rogue MAC address is used to spoof broadcast deassociation packets.C. The rogue MAC address is used to spoof broadcast deauthentication packets.D. The WCS sends out excessive signals on the same channel when the rogue is detected.



QUESTION 146With industry-leading services and performance, the Cisco Catalyst 6500 Series Switch is Cisco's flagshipswitching solution. It delivers the most comprehensive feature sets for core, distribution, wiring closet, datacenter, enterprise WAN routing, and Metro-Ethernet deployments. Which layer you think is recommended thatthe Cisco Catalyst 6500 Series WLSM be placed?

A. coreB. distributionC. accessD. presentation



QUESTION 147The Cisco Lifecycle Services approach defines the activities needed to help you successfully deploy andoperate Cisco technologies and optimize their performance throughout the lifecycle of your network. Whichstatement is an accurate list of Cisco Lifecycle Services phases?

A. initiation,prepare,plan,design,implement,operate,and optimizeB. site assessment,risk assessment,solution selection and acquisition,testing,and operationsC. prepare,plan,design,implement,operate,and optimizeD. deployment,testing,implementation,and production



QUESTION 148Which IP address or address range will be used when allocating an internal ip address to the VPN client for thetest?

A. 120.1.1.100 to 10.1.1.200B. 10.1.1.2 to 10.1.1.254C. 192.1681.1 to 192.1681.1.100D. 192.1681.2 to 192.1681.1.254



QUESTION 149Which authentication method is used by the test VPN group?

A. RSA EncryptedNonceB. RSA Digital SignatureC. Pre-shared keyD. DH2



QUESTION 150A network administrator is troubleshooting an EIGRP connection between RA and RB. Given the debug outputon RA, which two statements are true? (Choose two)

A. RA received a hello packet with mismatched hello timers.B. RA received a hello packet with mismatched metric-calculation mechanisms.C. RA will form an adjacency with RB.D. RAwill not form an adjacency with RB.



QUESTION 151You are the network administrator. There is one Gigabit Ethernet port on the Cisco CE520 used in the SmartBusiness Communications System. Which port role assignment would you make for?

A. Cisco Express 520B. Cisco UC520C. Cisco CE520D. Cisco 871W



QUESTION 152Refer to the exhibit. CK-SA and CK-SC are running PVST+ STP, and CK-SB is running 802.1 Q STP. If theBPDU of the root in VLAN 1 is better than the BPDU of the root in VU\N 2, then there is no blocking port in theVLAN 2 topology. The BPDU of VLAN 2 never makes a "full circle" around the topology; it is replaced by theVLAN 1 BPDU on the CK-SB-CK-SC link, because CK-SB runs only one STP merged with VLAN 1 STP ofPVST+. Thus, there is a forwarding loop.

What does PVST+ do to correct this?

A. CK-SA sends PVST+ BPDUs ofVLAN2 (to the SSTP address that is flooded by CK-SB) towards CK-SC.CK-SC will put port CK-SC-CK-SB into a type-inconsistent state,which prevents the loop.

B. CK-SB sends PVST+ BPDUs of VLAN 1 (to the SSTP address that is flooded by CK-SA) towards CK-SC.CK-SC will put port CK-SC-CK-SB into a type-inconsistent state,which prevents the loop.

C. CK-SC sends PVST+BPDUs of VLAN 2 (to the SSTP address that is flooded by CK-SB) towards CK-SC.CK-SAwill put port CK-SC-CK-SB into a type-inconsistent state,which prevents the loop.

D. CK-SA sends PVST+ BPDUs of VLAN 1 (to the SSTP address that is flooded by CK-SB) towards CK-SB.CK-SA will put port CK-C-CK-B into a type-inconsistent state,which prevents the loop.



QUESTION 153A wireless autonomous 1200 access point running core feature set in root mode has its SSID set toFactory_floor and provides connection to a repeater access point with its SSID set to factory_floor, if the root-mode access point is using channel 11 . which channel will the repeater access point use?

A. channel 11B. channel 1 or 6C. any nonoverlapping channelD. The root access point and the repeater will negotiate this setting



QUESTION 154The VPN server uses a preshared key for remote device authentication

A. TRUEB. FALSE



QUESTION 155A customer with a large enterprise network wants to allow employees to work from home over the Internet. Thecustomer anticipates a large amount of traffic, predominantly toward the central site. The customer alsorequires a VPN using strong user authentication and encryption to protect highly sensitive data. Which solutionbest meets this customer's requirements?

A. remote-access VPN with software encryptionB. remote-access VPN with hardware encryptionC. site-to-site VPN with hub-and-spoke tunnels using 3DES and pre-shared secretsD. site-to-site Cisco Easy VPN



QUESTION 156The tables contain information from the Cisco Router and Security Device Manager configurations of RA andRB. Traffic between PC1 and PC2 is not successfully establishing the site-to-site VPN between -RA and -RB.What is the mostly likely cause of this fault?

A. RAis using a standard IP ACL (100-149) while RB is using a Turbo ACL(150-199).B. The IPSec encryption methods used by each router do not match.C. The D-H Group settings on the two routers are the same.D. The IPSec rules on the two routers are not permitting the correct interesting traffic.



QUESTION 157You are the network consultant. When will you assess a customer's current network infrastructure?

A. plan

B. designC. operateD. optimize



QUESTION 158A client is experiencing lower throughput and more packet retransmits is one area of the wireless network. Atthese times, the client utility shows high signal strength but low signal quality. What may be causing this issue?

A. The client does not support Cisco Compatible Extensions version 2.B. Diversity is not enabled in the access point.C. The WDS is failing to register the client card in the WLSM.D. The channel is set incorrectly in the access point or in the client configuration.



QUESTION 159Which statement is correct about the current address translation configurations on the security appliance?

A. Dynamic NAT is used to translate the 10.0.1.100 host on the inside interface to a global address of192.168.1.1

B. Port Address Translation(PAT) is used to translate any host on the inside interface to the 192.168.1.100global address.

C. Static NAT is used to translate the 172.16.1.2 host on the dmzl interface to a global address of192.168.1.102

D. Dynamic NAT is used to translate any host on dmzl and dmz2 interfaces to a mapped address from theaddress from the address pool of 192.168.1.110 to 192.168.1.250



QUESTION 160VLAN Hopping is one of the primary VLAN based attacks used by hackers to infiltrate network security. VLANhopping is used to attack a network by sending packets to a port which is generally not accessible. VLANhopping attacks are mainly conducted in the Dynamic Trunking Protocol and, in some cases; the attacks aretargeted to the trunking encapsulation protocol (802.1 q or ISL).You worry about the switched infrastructure inan integrated network is vulnerable to VLAN hopping attacks. Which two configuration can be used to mitigateVLAN hopping? (Choose two.)

A. switchporttrunk encapsulationB. switchport mode trunk

C. switchport access vlanD. switchport mode access



QUESTION 161CiscoWorks SNMS is a part of the CiscoWorks family of products for managing small to large networks.CiscoWorks SIMMS is a new Web-based network management solution for small to medium-sized businesses,with 40 or fewer Cisco internetworking devices such as switches, routers, hubs, and access servers.CiscoWorks SNMS can also monitor third-party IT assets such as servers, applications, services, and printers.A Public Switched Telephone Network (PSTN) trunk is typically the voice interconnect between any businessand the outside world.Which network management tool is designed to allow businesses to manage up to 40 devices?

A. CiscoWorks UnrestrictedB. CiscoWorks WAN ManagementC. CiscoWorks LAN ManagementD. CiscoWorks SNMS



QUESTION 162Which statement is correct about the information in the Cisco Adaptive Security Device Manager General andLicense Information screen?

A. The security appliance supports active/active failover only.B. The security appliance supports 3DES-AES only.C. The managed device is a Cisco ASA 5540 Security Appliance with VPN premium license enabled.D. The managed device is Cisco PIX515E Security Appliance.



QUESTION 163Which three are different types of STP inconsistencies in a Layer 2 network? (Choose three)

A. MAC inconsistencyB. Root inconsistencyC. EtherChannel inconsistencyD. type inconsistency

Correct Answer: BCD



QUESTION 164According to the error log

VLAN 1 is where the BPDU was received, and VLAN 2 is where the BPDU originated. When inconsistency isdetected, what happens?

A. VLAN 1 is blocked,while VLAN 2 is forwardingB. VLAN1 is blocked,while VLAN 2 is listeningC. Both VLANs are listening on the port from which this BPDU is sendD. Both VLANs are blocked on the port from which this BPDU is received



QUESTION 165Which is the current configured default gateway IP address on the security appliance?

A. 172.16.10.1B. 172.16.1.1C. 192.168.1.2D. 10.0.1.1



QUESTION 166Which statement is true about a Cisco Aironet 350 Series wireless client when its green LED appears to be offand its amber LED is blinking?

A. The client adapter is scanning for a network.

B. The client adapter is in ad hoc mode.C. The client adapter is performing a self-test.D. The client adapter is in power-save mode.



QUESTION 167You are the Cisco Configuration Assistant. Your IT Manager tells you 802.11b telephone can receive an audiosignal from an access point, but cannot send audio. What is the most likely reason?

A. The value of RSSI telephone is greater than 30.B. The access point only receives 802.11g data rates.C. The security settings in the telephone mismatch the access point.D. The telephone transmit power is significantly lower than the t the access point



QUESTION 168You are migrating the network design from using point security products (perimeter router, firewall, VPN router,IPS) to an integrated security solution using Cisco ISR. During the migration process, you determine that youneed to improve VPN performance. What can you do?

A. Upgrade the Cisco IOS image on the ISR to the V3PN bundleB. Increase the RAM on the ISRC. Install AIM-VPN EPII-PLUS on the ISRD. Enable transparent tunneling using IPSec over TCP




A company has just set up an e-commerce webhost on the DMZ. It was designed so that partners can entertheir equipment orders via a secure interface on a security appliance. The first time a partner tried to access thee-commerce webhost at http://172.16.1.2, the partner could not gain access to the webhost. After reviewing thenetwork diagram, the Cisco Adaptive Security Device Manager translation table, and Cisco ASDM access listconfiguration shown in the exhibit, what did the corporate network administrator determine to be the cause ofthe problem?

A. The pnet static translation entry is not configured correctly.B. The URL that the partner is using is not configured correctly.C. The pnet-access access list is not configured correctly.D. The pnet global address is not configured correctly.



QUESTION 170A company needs to provide site-to-site VPN, remote access VPN, and firewall protection. Which device bestsupports al three functions?

A. Cisco PIXB. Cisco ASAC. Cisco ConcentratorD. Cisco Router and Security Device Manager



QUESTION 171The network administrator has configured the SSID value in a wireless Cisco Aironet client card. What is the

result of the client-to-access-point association if the client SSID1 is left blank, and the SSID2 is assigned avalue of my_ssid?

A. The client will consider SSID1 a null value,causing the client to request the SSID from the access point.B. The client software will not allow this configuration and will create an error message until the configuration is

corrected.C. The client software will replace SSID1 with SSID2,and use my_ssid to attempt association with the access

point.D. The client software will attempt association with the access point using a null value of SSID1,and if not

successful it will rotate to use the SSID2 value of my_ssid.



QUESTION 172You have applied a firewall configuration to your router using the Cisco Router and Security Device Manager(SDM) Firewall wizard. You find that you are now locked out and access via Cisco SDM is denied. Afteraccessing the router via the console port, what must you do to regain access via Cisco SDM?

A. Generate an RSA key pair between the host and device to allow secure access.B. Specify the Cisco SDM management port number to gain access.C. Create a loopback interface and connect to that IP address for management purposes when the

configuration has been applied to the router.D. Modify the access list that denies Cisco SDM access.




According to the Cisco VPN Client software outputs shown, which two statements are correct about theconnection entry named isr? (Choose two.)

A. HMAC-SHA1 is used to authenticate the remote users.B. Preshared key is used to authenticate the remote peer.C. AES is used to provide data confidentiality.D. The Cisco VPN Client software is assigned an internal IP address of 192.168.1.1.E. The PC that is running the Cisco VPN Client software will not have access to the local LAN once the PC is

connected into the VPN.



QUESTION 174

Refer to the exhibit.

Which statement is correct about the information in the Cisco Adaptive Security Device Manager General andLicense Information screen?

A. The security appliance supports active/active failover only.B. The security appliance supports 3DES-AES only.C. The managed device is a Cisco ASA 5540 Security Appliance with VPN premium license enabled.D. The managed device is a Cisco PIX515E Security Appliance.



QUESTION 175HOTSPOT

A.B.C.D.

Correct Answer: Section: (none)Explanation


QUESTION 176HOTSPOT

A.B.C.D.



QUESTION 177HOTSPOT

A.B.C.D.



QUESTION 178HOTSPOT

B.C.D.



QUESTION 179When implementing an integrated network-security management design, which critical issue should youaccount for?

A. that full syslogging of all events is enabledB. that management stations intercommunicate and can correlate eventsC. that SNMP community read-write strings are configured to allow for total management accessD. that all network devices are time synchronized



QUESTION 180When using Cisco Router and Security Device Manager (SDM) to configure IPS, what must you do first before

you can select Configure > Signature to edit any signatures?

A. Select Configure > Global Settings to disable the Failed Closed option.B. Select Configure > Rules to enable an interface for inbound and/or outbound IPS.C. Select Configure > Global Settings to point Cisco SDM to the ips.tar file in the router Flash memory.D. Select Configure > Rules to create the inbound and/or outbound filter to determine which traffic will be

scanned by IPS.E. Select Configure > Global Settings to enable IPS globally on the router.



QUESTION 181After performing a security audit in Cisco Router and Security Device Manager (SDM), you receive this as oneof the results: Enable Unicast RPF on all outside interfaces - Not Passed. Which Cisco SDM configurationwizard can be use to resolve this?

A. Edit Interface/ConnectionB. Basic FirewallC. NATD. Easy VPN ServerE. RoutingF. Site to Site VPN



QUESTION 182You have enabled SDEE to report Cisco IOS IPS events. However, when you attempt to view IPS events, noneare available for viewing. Which two should you verify to ensure that your configuration is correct? (Choosetwo.)

A. that ip ips notify sdee is enabledB. that you are connecting to the proper SDEE engine port numberC. that the receiving host IP address and secret key are correctly configuredD. that ip ips deny-action parameters are enabledE. that ip http server is enabledF. that you have a valid number of subscriptions enabled

Correct Answer: AESection: (none)Explanation


QUESTION 183

Several users have reported problems accessing the new company web server. How can the administrator testto ensure that all layers of the OSI model are working?

A. Telnet to port 80 of the web server.B. Use the show ip http server command.C. Ping the IP address of the web server.D. Use the netstat -r command.E. Use the debug ip http server command.F. Ping the web server by name.



QUESTION 184Which two statements best describe the installation of Cisco Aironet LAN Client Adapters? (Choose two.)

A. Cisco ACAU automates the deployment of Cisco ACU.B. Cisco ACU is for the 802.11a/b/g radio client card.C. Cisco ACAU automates the deployment of Cisco ADU.D. Cisco ADU is for the 802.11a/b/g radio client card.



QUESTION 185When using the Site to Site VPN wizard in Cisco Router and Security Device Manager, why would you need tocreate an access list using the Add a Rule screen?

A. to open holes on the firewall to permit ISAKMP,ESP,and AH trafficB. to enable split tunnelingC. to specify the remote-peer IP address rangeD. to specify a range of IP addresses on the inside interfaceE. to define the traffic that will be protected by IPSec



QUESTION 186Refer to the exhibit. You are asked to implement a network design that consists of two sites, the main officeand one branch office connected via the Internet. Communications between these sites must be secure. Themain office site also supports 30 local users and 15 remote mobile workers. Before gaining access to theinternal network, both the local users and the mobile workers should be authenticated using a scalable solution.Before you begin the implementation, you need to identify which security component is missing in the design.

A. CBAC on the perimeter routerB. 802.1x authenticatorC. Cisco VPN 3000 Series ConcentratorD. Cisco PIX Security ApplianceE. network-based IDSF. ACS

Correct Answer: FSection: (none)Explanation


QUESTION 187A user is not able to access the Cisco Router and Security Device Manager (SDM) via HTTPS. Which twosituations could be causing the problem? (Choose two.)

A. The ip http secure-server command is not in the running-config.B. The user is trying to launch Cisco SDM from the inside (secured) interface with firewall enabled.C. The ip https server command is not in the running-config.D. The user does not have a privilege level of 15.



QUESTION 188Refer to the exhibit. Cisco Router and Security Device Manager (SDM) is being used to configure EIGRP forthe first time. Which three statements are correct about the Add a EIGRP display window? (Choose three.)

A. The IP address masks of interfaces FastEthernet 0/0 and FastEthernet 0/1 must match their correspondingnetwork statements in the EIGRP routing protocol for routing updates to be exchanged.

B. It is possible to configure the auto summary behavior of EIGRP 100 on R2 using Cisco SDM.C. R3 will not receive any EIGRP updates from R2.D. The various network and mask configurations under EIGRP 100 can be reduced to a single line of

172.16.224.0 0.0.31.255.E. It is possible to configure multiple instances of EIGRP on R2 using Cisco SDM,providing the autonomous

systems numbers do not conflict.F. R1 will not receive any EIGRP updates from R2.

Correct Answer: CDE



QUESTION 189Refer to the exhibit. Based on the IPS configuration, which two types of traffic will be scanned by Cisco IOSIPS? (Choose two.)

A. inbound HTTP traffic from host 10.1.1.1 to FastEthernet 0/0 interfaceB. all inbound traffic to the FastEthernet 0/0 interface or the FastEthernet 0/1 interfaceC. inbound Telnet traffic from host 192.168.1.1 to the FastEthernet 0/0 interfaceD. inbound HTTP traffic from host 10.2.2.2 to the FastEthernet 0/0 interfaceE. all inbound traffic to the FastEthernet 0/0 interfaceF. all inbound and outbound traffic to the FastEthernet 0/0 interface



QUESTION 190Users logging into Cisco Router and Security Device Manager (SDM) should be authenticated using the CiscoISR local user database. Currently, none of the users can access the Cisco SDM via HTTP. Which command

or commands should be verified as properly configured on the ISR to resolve this problem?

A. line con 0 login localB. line vty 0 5 login localC. ip http secure-serverD. ip http authentication localE. aaa new-model aaa authentication login default localF. aaa new-model aaa authorization exec default local



QUESTION 191You are migrating the network design from using point security products (perimeter router, firewall, VPN router,IPS) to an integrated security solution using the Cisco ISR. During the migration process, you determine thatyou need to improve the VPN performance. What can you do?

A. Install the AIM-VPN/EPII-PLUS on the ISR.B. Upgrade the Cisco IOS image on the ISR to the V3PN bundle.C. Use AES encryption instead of 3DES.D. Increase the RAM on the ISR.E. Enable transparent tunneling using IPSec over UDP.F. Enable transparent tunneling using IPSec over TCP.



QUESTION 192What is not a correct statement about PoE ports that are implemented on Cisco Catalyst 4500 Series switches?

A. They deliver power for a distance up to 100 meters over standard Category 5 UTP cable.B. They can distinguish an unpowered NIC.C. They provide -48 VDC power over standard Category 5 UTP cable.D. They can distinguish an IEEE 802.1af powered device.E. They can distinguish a Cisco prestandard device.



QUESTION 193When will you need to enable the transparent tunneling feature on the Cisco VPN Client software?

A. to enable V3PN

B. if the IPSec-protected traffic is going through a router that is performing NAT or PATC. to enable DMVPND. to enable dynamic routing over the IPSec tunnel using GREE. if IPSec is using tunnel mode instead of transport mode



QUESTION 194Under normal operation, which light sequence on the Cisco Aironet 1300 Wireless Bridge indicates that adevice is associated to the bridge?

A. The center LED (Status) flashes green once every 3 seconds.B. The center LED (Status) is solid green.C. The center LED (Status) flashes green once every second.D. The center LED (Status) blinks amber when an association occurs.



QUESTION 195What is the default authentication method when using HTTP to access the Cisco Router and Security DeviceManager (SDM), assuming that you are not using the default configuration file (sdmconfig-xxxx.cfg) that comeswith Cisco SDM?

A. aaaB. enable passwordC. noneD. local databaseE. line console passwordF. line vty password



QUESTION 196Which two items have the most influence on an outdoor wireless antenna bridge-path installation? (Choosetwo.)

A. Fresnel zoneB. lightningC. snowD. Earth's curvature

E. rain



QUESTION 197Which two statements are correct about using Cisco Router and Security Device Manager (SDM) to configureRIP routing protocol? (Choose two.)

A. Cisco SDM allows the configuration of RIPv2 network masks.B. Cisco SDM allows the configuration of RIPv1 and RIPv2.C. Cisco SDM allows leaving the selection of the RIP protocol version to the default of the installed Cisco IOS

software.D. Cisco SDM allows the configuration only of RIPv2.



QUESTION 198An administrator at host address 10.0.1.11 is trying to gain access to Cisco Adaptive Security Device Managervia a Cisco ASA Security Appliance inside interface at IP address 10.0.1.1. Which two commands are requiredon a security appliance to enable Cisco ASDM access? (Choose two.)

A. http 10.0.1.1 255.255.255.255 insideB. Access-list asdm_access permit tcp host 10.0.1.11 host 10.0.1.1 eq http ! http (inside) match asdm_access

!C. asdm-management enableD. http server enableE. http (inside) host 10.0.1.11F. Access-list asdm_access permit tcp host 10.0.1.11 host 10.0.1.1 eq http asdm-map ASDM match

asdm_access



QUESTION 199DRAG DROPIFEE S. IHEDORO Foundation Express for Field Engineers 01:03:21Question of Question 59 of 59

A.B.C.D.



QUESTION 200Which four features can be configured using Cisco Router and Security Device Manager version 2.1.1?(Choose four.)

A. static routes and IGP routing protocols (OSPF,RIP,EIGRP)B. Easy VPN Remote and Easy VPN ServerC. SSL VPN (WebVPN)D. IPSE. IP multicast routing (PIM)F. AAA

Correct Answer: ABDFSection: (none)Explanation


Cisco.Yesuse.648-385.v2013-04-18.by.yofe · 2019-10-17 · A host on the Sales subnet (10.0.2.0/24)...

Documents

Transcript of Cisco.Yesuse.648-385.v2013-04-18.by.yofe · 2019-10-17 · A host on the Sales subnet (10.0.2.0/24)...