Cisco Certified Network Associate Version 2...

Cisco Certified Network Associate Version 2 (200-120)

The following topics are general guidelines for the content likely to be included on the exam. However, other related topics may also appear on any specific delivery of the exam. In order to better reflect the contents of the exam and for clarity purposes, the guidelines below may change at any time without notice. 5% 1.0 Operation of IP Data Networks

1.1 Recognize the purpose and functions of various network devices such as routers, switches, bridges and hubs

1.2 Select the components required to meet a given network specification 1.3 Identify common applications and their impact on the network 1.4 Describe the purpose and basic operation of the protocols in the OSI and TCP/IP models 1.5 Predict the data flow between two hosts across a network 1.6 Identify the appropriate media, cables, ports, and connectors to connect Cisco network

devices to other network devices and hosts in a LAN

20% 2.0 LAN Switching Technologies

2.1 Determine the technology and media access control method for Ethernet networks 2.2 Identify basic switching concepts and the operation of Cisco switches

2.2.a Collision Domains 2.2.b Broadcast Domains 2.2.c Ways to switch

2.2.c (i) Store 2.2.c (ii) Forward 2.2.c (iii) Cut through

2.2.d CAM Table

[email protected]

[email protected] www.netexpertsindia.com

www.netexperts-ies.com

www.netexpertsindia.com















https://learningnetwork.cisco.com/community/certifications/ccna

https://learningnetwork.cisco.com/community/certifications/ccna


2.3 Configure and verify initial switch configuration including remote access management 2.3.a hostname 2.3.b mgmt ip address 2.3.c ip default-gateway 2.3.d local user and password 2.3.e enable secret password 2.3.f console and VTY logins 2.3.g exec-timeout 2.3.h service password encryption 2.3.i copy run start

2.4 Verify network status and switch operation using basic utilities such as 2.4.a ping 2.4.b telnet 2.4.c SSH

2.5 Describe how VLANs create logically separate networks and the need for routing between them 2.5.a Explain network segmentation and basic traffic management concepts

2.6 Configure and verify VLANs 2.7 Configure and verify trunking on Cisco switches

2.7.a dtp (topic) 2.7.b auto-negotiation

2.8 Identify enhanced switching technologies 2.8.a RSTP 2.8.b PVSTP 2.8.c Etherchannels

2.9 Configure and verify PVSTP operation 2.9.a Describe root bridge election 2.9.b Spanning tree mode

5% 3.0 IP Addressing (IPv4/IPv6)

3.1 Describe the operation and necessity of using private and public IP addresses for IPv4 addressing

3.2 Identify the appropriate IPv6 addressing scheme to satisfy addressing requirements in a

LAN/WAN environment 3.3 Identify the appropriate IPv4 addressing scheme using VLSM and summarization to

satisfy addressing requirements in a LAN/WAN environment 3.4 Describe the technological requirements for running IPv6 in conjunction with IPv4

3.4.a dual stack

















3.5 Describe IPv6 addresses 3.5.a global unicast 3.5.b multicast 3.5.c link local 3.5.d unique local 3.5.e eui 64 3.5.f auto-configuration

20% 4.0 IP Routing Technologies

4.1 Describe basic routing concepts 4.1.a packet forwarding 4.1.b router lookup process 4.1.c Process Switching/Fast Switching/CEF

4.2 Configure and verify utilizing the CLI to set basic Router configuration 4.2.a hostname 4.2.b local user and password 4.2.c enable secret password 4.2.d console & VTY logins 4.2.e exec-timeout 4.2.f service password encryption 4.2.g interface IP Address

4.2.g (i) loopback 4.2.h banner 4.2.i motd 4.2.j copy run start

4.3 Configure and verify operation status of a device interface 4.3.a Serial 4.3.b Ethernet

4.4 Verify router configuration and network connectivity using

4.4.a ping 4.4.a (i) extended

4.4.b traceroute 4.4.c telnet 4.4.d SSH 4.4.e sh cdp neighbors

4.5 Configure and verify routing configuration for a static or default route given specific routing requirements

4.6 Differentiate methods of routing and routing protocols

4.6.a Static vs. dynamic 4.6.b Link state vs. distance vector 4.6.c next hop 4.6.d ip routing table 4.6.e Passive Interfaces (how they work)

















4.6.f Admin distance 4.6.g split horizon 4.6.h metric

4.7 Configure and verify OSPF

4.7.a Benefit of single area 4.7.b Configure OSPv2 4.7.c Configure OSPv3 4.7.d Router ID 4.7.e Passive Interface 4.7.f Discuss multi-area OSPF 4.7.g Understand LSA types and purpose

4.8 Configure and verify interVLAN routing (Router on a stick)

4.8.a sub interfaces 4.8.b upstream routing 4.8.c encapsulation

4.9 Configure SVI interfaces

4.10 Manage Cisco IOS Files

4.10.a Boot Preferences 4.10.b Cisco IOS Images (15) 4.10.c Licensing

4.10.c (i) Show license 4.10.c (ii) Change license

4.11 Configure and verify EIGRP (single AS)

4.11.a Feasible Distance/Feasible Successors/Administrative distance 4.11.b Feasibility condition 4.11.c Metric composition 4.11.d Router ID 4.11.e Auto summary 4.11.f Path Selection 4.11.g Load Balancing

4.11.g (i) Unequal 4.11.g (ii) Equal

10% 5.0 IP Services

5.1 Configure and verify DHCP (IOS Router) 5.1.a Configuring router interfaces to use DHCP 5.1.b DHCP options (Basic overview and functionality) 5.1.c Excluded addresses 5.1.d Lease time

5.2 Describe the types, features, and applications of ACLs

5.2.a standard (editing and sequence numbers) 5.2.b extended

















5.2.c named 5.2.d numbered 5.2.e Log option

5.3 Configure and verify ACLs in a network environment

5.3.a named 5.3.b numbered 5.3.c Log option

5.4 Identify the basic operation of NAT 5.4.a purpose 5.4.b pool 5.4.c static 5.4.d 1 to 1 5.4.e overloading 5.4.f source addressing 5.4.g one way NAT

5.5 Configure and verify NAT for given network requirements 5.6 Configure and verify NTP as a client 5.7 Recognize High availability (FHRP)

5.7.a VRRP 5.7.b HSRP 5.7.c GLBP

5.8 Configure and verify syslog

5.8.a Utilize syslog output

5.9 Describe SNMP v2 and v3. 10% 6.0 Network Device Security

6.1 Configure and verify network device security features 6.1.a Device password security 6.1.b Enable secret vs. enable 6.1.c Transport

6.1.c.1 disable telnet 6.1.c.2 SSH

6.1.d VTYs 6.1.e physical security 6.1.f service password 6.1.g Describe external authentication methods

6.2 Configure and verify Switch Port Security

6.2.a Sticky MAC 6.2.b MAC address limitation 6.2.c static/dynamic

















6.2.d violation modes 6.2.d (i) err disable 6.2.d (ii) shutdown 6.2.d (iii) protect restrict

6.2.e Shutdown unused ports 6.2.f err disable recovery 6.2.g Assign unused ports in unused VLANs 6.2.h Putting Native VLAN to other than VLAN 1

6.3 Configure and verify ACLs to filter network traffic 6.4 Configure and verify ACLs to limit telnet and SSH access to the router

20% 7.0 Troubleshooting

7.1 Troubleshoot and correct common problems associated with IP addressing and host configurations

7.2 Troubleshoot and resolve VLAN problems

7.2.a Identify that VLANs are configured 7.2.b Verify port membership correct 7.2.c Correct IP address configured

7.3 Troubleshoot and resolve trunking problems on Cisco switches

7.3.a Verify correct trunk states 7.3.b Verify correct encapsulation configured 7.3.c Correct VLANs allowed

7.4 Troubleshoot and resolve ACL issues

7.4.a Verify statistics 7.4.b Verify permitted networks 7.4.c Verify direction

7.4.c (i) Interface

7.5 Troubleshoot and resolve Layer 1 problems 7.5.a Framing 7.5.b CRC 7.5.c Runts 7.5.d Giants 7.5.e Dropped packets 7.5.f Late collisions 7.5.g Input/output errors

7.6 Identify and correct common network problems

7.7 Troubleshoot and resolve spanning tree operation issues

7.7.a Verify root switch 7.7.b Verify priority 7.7.c Verify mode is correct

















7.7.d Verify port states

7.8 Troubleshoot and resolve routing issues 7.8.a Verify routing is enabled (sh ip protocols) 7.8.b Verify routing table is correct 7.8.c Verify correct path selection

7.9 Troubleshoot and resolve OSPF problems

7.9.a Verify neighbor adjacencies 7.9.b Verify hello and dead timers 7.9.c Verify OSPF area 7.9.d Verify interface MTU 7.9.e Verify network types 7.9.f Verify neighbor states 7.9.g Review OSPF topology table

7.10 Troubleshoot and resolve EIGRP problems

7.10.a Verify neighbor adjacencies 7.10.b Verify AS number 7.10.c Verify load balancing 7.10.d Split horizon

7.11 Troubleshoot and resolve interVLAN routing problems

7.11.a Verify connectivity 7.11.b Verify encapsulation 7.11.c Verify subnet 7.11.d Verify native VLAN 7.11.e Port mode trunk status

7.12 Troubleshoot and resolve WAN implementation issues

7.12.a Serial interfaces 7.12.b Frame relay 7.12.c PPP

7.13 Monitor NetFlow statistics

7.14 TS EtherChannel problems

10% 8.0 WAN Technologies

8.1 Identify different WAN Technologies 8.1.a Metro ethernet 8.1.b VSAT 8.1.c Cellular 3g/4g 8.1.d MPLS 8.1.e T1/E1 8.1.f ISDN 8.1.g DSL 8.1.h Frame relay

















8.1.i Cable 8.1.j VPN

8.2 Configure and verify a basic WAN serial connection 8.3 Configure and verify a PPP connection between Cisco routers 8.4 Configure and verify frame relay on Cisco routers 8.5 Implement and troubleshoot PPPoE

702, Somdatt Chambers - II, Bhikaji Cama Place, New Delhi - 110066 (INDIA)

















Implementing Cisco IP Routing (300-101)

Exam Description: Implementing Cisco IP Routing (ROUTE 300-101) is a 120-minute qualifying exam with 50‒60 questions for the Cisco CCNP and CCDP certifications. The ROUTE 300-101 exam certifies the routing knowledge and skills of successful candidates. They are certified in using advanced IP addressing and routing in implementing scalable and highly secure Cisco routers that are connected to LANs, WANs, and IPv6. The exam also covers the configuration of highly secure routing solutions to support branch offices and mobile workers. The following topics are general guidelines for the content that is likely to be included on the exam. However, other related topics may also appear on any specific version of the exam. To better reflect the contents of the exam and for clarity, the following guidelines may change at any time without notice.

10% 1.0 Network Principles

1.1 Identify Cisco Express Forwarding concepts 1.1.a FIB 1.1.b Adjacency table

1.2 Explain general network challenges

1.2.a Unicast 1.2.b Out-of-order packets 1.2.c Asymmetric routing

1.3 Describe IP operations

1.3.a ICMP Unreachable and Redirects 1.3.b IPv4 and IPv6 fragmentation 1.3.c TTL

1.4 Explain TCP operations

1.4.a IPv4 and IPv6 (P)MTU 1.4.b MSS 1.4.c Latency 1.4.d Windowing 1.4.e Bandwidth-delay product 1.4.f Global synchronization

1.5 Describe UDP operations

1.5.a Starvation 1.5.b Latency

[email protected]

[email protected] www.netexpertsindia.com

www.netexperts-ies.com

















1.6 Recognize proposed changes to the network 1.6.a Changes to routing protocol parameters 1.6.b Migrate parts of the network to IPv6 1.6.c Routing protocol migration

10% 2.0 Layer 2 Technologies

2.1 Configure and verify PPP 2.1.a Authentication (PAP, CHAP) 2.1.b PPPoE (client side only)

2.2 Explain Frame Relay

2.2.a Operations 2.2.b Point-to-point 2.2.c Multipoint


3.1 Identify, configure, and verify IPv4 addressing and subnetting 3.1.a Address types (Unicast, broadcast, multicast, and VLSM) 3.1.b ARP 3.1.c DHCP relay and server 3.1.d DHCP protocol operations

3.2 Identify IPv6 addressing and subnetting

3.2.a Unicast 3.2.b EUI-64 3.2.c ND, RS/RA 3.2.d Autoconfig (SLAAC) 3.2.e DHCP relay and server 3.2.f DHCP protocol operations

3.3 Configure and verify static routing

3.4 Configure and verify default routing

3.5 Evaluate routing protocol types

3.5.a Distance vector 3.5.b Link state 3.5.c Path vector

3.6 Describe administrative distance 3.7 Troubleshoot passive interfaces 3.8 Configure and verify VRF lite 3.9 Configure and verify filtering with any protocol 3.10 Configure and verify redistribution between any routing protocols or routing sources

















3.11 Configure and verify manual and autosummarization with any routing protocol 3.12 Configure and verify policy-based routing 3.13 Identify suboptimal routing 3.14 Explain ROUTE maps 3.15 Configure and verify loop prevention mechanisms

3.15.a Route tagging and filtering 3.15.b Split-horizon 3.15.c Route poisoning

3.16 Configure and verify RIPv2 3.17 Describe RIPng 3.18 Describe EIGRP packet types 3.19 Configure and verify EIGRP neighbor relationship and authentication 3.20 Configure and verify EIGRP stubs 3.21 Configure and verify EIGRP load balancing

3.21.a Equal cost 3.21.b Unequal cost

3.22 Describe and optimize EIGRP metrics 3.23 Configure and verify EIGRP for IPv6 3.24 Describe OSPF packet types 3.25 Configure and verify OSPF neighbor relationship and authentication 3.26 Configure and verify network types, area types, and router types

3.26.a Point-to-point, multipoint, broadcast, nonbroadcast 3.26.b LSA types, area type: backbone, normal, transit, stub, NSSA, totally stub 3.26.c Internal router, backbone router, ABR, ASBR 3.26.d Virtual link

3.27 Configure and verify OSPF path preference 3.28 Configure and verify OSPF operations 3.29 Configure and verify OSPF for IPv6

















3.30 Describe, configure, and verify BGP peer relationships and authentication 3.30.a Peer group 3.30.b Active, passive 3.30.c States and timers

3.31 Configure and verify eBGP (IPv4 and IPv6 address families)

3.31.a eBGP 3.31.b 4-byte AS number 3.31.c Private AS

3.32 Explain BGP attributes and best-path selection

10% 4.0 VPN Technologies 4.1 Configure and verify GRE 4.2 Describe DMVPN (single hub) 4.3 Describe Easy Virtual Networking (EVN)

10% 5.0 Infrastructure Security 5.1 Describe IOS AAA using local database 5.2 Describe device security using IOS AAA with TACACS+ and RADIUS

5.2.a AAA with TACACS+ and RADIUS 5.2.b Local privilege authorization fallback

5.3 Configure and verify device access control

5.3.a Lines (VTY, AUX, console) 5.3.b Management plane protection 5.3.c Password encryption

5.4 Configure and verify router security features

5.4.a IPv4 access control lists (standard, extended, time-based) 5.4.b IPv6 traffic filter 5.4.c Unicast reverse path forwarding

20% 6.0 Infrastructure Services

6.1 Configure and verify device management 6.1.a Console and VTY

6.1.b Telnet, HTTP, HTTPS, SSH, SCP 6.1.c (T)FTP

6.2 Configure and verify SNMP

6.2.a v2 6.2.b v3

6.3 Configure and verify logging

6.3.a Local logging, syslog, debugs, conditional debugs 6.3.b Timestamps

















6.4 Configure and verify Network Time Protocol (NTP) 6.4.a NTP master, client, version 3, version 4 6.4.b NTP authentication

6.5 Configure and verify IPv4 and IPv6 DHCP

6.5.a DHCP client, IOS DHCP server, DHCP relay 6.5.b DHCP options (describe)

6.6 Configure and verify IPv4 Network Address Translation (NAT)

6.6.a Static NAT, dynamic NAT, PAT

6.7 Describe IPv6 NAT 6.7.a NAT64 6.7.b NPTv6

6.8 Describe SLA architecture 6.9 Configure and verify IP SLA

6.9.a ICMP

6.10 Configure and verify tracking objects 6.10.a Tracking objects 6.10.b Tracking different entities (for example, interfaces, IPSLA results)

6.11 Configure and verify Cisco NetFlow

6.11.a NetFlow v5, v9 6.11.b Local retrieval 6.11.c Export (configuration only)

















Implementing Cisco IP Switched Networks (300-115)

Exam Description: Implementing Cisco IP Switched Networks (SWITCH 300-115) is a 120-minute qualifying exam with 45‒55 questions for the Cisco CCNP and CCDP certifications. The SWITCH 300-115 exam certifies the switching knowledge and skills of successful candidates. They are certified in planning, configuring, and verifying the implementation of complex enterprise switching solutions that use the Cisco Enterprise Campus Architecture. The SWITCH exam also covers highly secure integration of VLANs and WLANs. The following topics are general guidelines for the content that is likely to be included on the exam. However, other related topics may also appear on any specific version of the exam. To better reflect the contents of the exam and for clarity, the following guidelines may change at any time without notice.


1.1 Configure and verify switch administration 1.1.a SDM templates

1.1.b Managing MAC address table

1.1.c Troubleshoot Err-disable recovery

1.2 Configure and verify Layer 2 protocols 1.2.a CDP, LLDP 1.2.b UDLD

1.3 Configure and verify VLANs

1.3.a Access ports 1.3.b VLAN database 1.3.c Normal, extended VLAN, voice VLAN

1.4 Configure and verify trunking

1.4.a VTPv1, VTPv2, VTPv3, VTP pruning 1.4.b dot1Q 1.4.c Native VLAN 1.4.d Manual pruning

1.5 Configure and verify EtherChannels

1.5.a LACP, PAgP, manual 1.5.b Layer 2, Layer 3 1.5.c Load balancing 1.5.d EtherChannel misconfiguration guard

1.6 Configure and verify spanning tree

















1.6.a PVST+, RPVST+, MST 1.6.b Switch priority, port priority, path cost, STP timers 1.6.c PortFast, BPDUguard, BPDUfilter 1.6.d Loopguard and Rootguard

1.7 Configure and verify other LAN switching technologies

1.7.a SPAN, RSPAN

1.8 Describe chassis virtualization and aggregation technologies 1.8.a Stackwise

20% 2.0 Infrastructure Security

2.1 Configure and verify switch security features 2.1.a DHCP snooping 2.1.b IP Source Guard 2.1.c Dynamic ARP inspection 2.1.d Port security 2.1.e Private VLAN 2.1.f Storm control

2.2 Describe device security using Cisco IOS AAA with TACACS+ and RADIUS

2.2.a AAA with TACACS+ and RADIUS 2.2.b Local privilege authorization fallback


3.1 Configure and verify first-hop redundancy protocols 3.1.a HSRP 3.1.b VRRP 3.1.c GLBP

















Troubleshooting and Maintaining Cisco IP Networks v2 (300-135)

Exam Description: Troubleshooting and Maintaining Cisco IP Networks v2 (TSHOOT 300-135) is a 120-minute qualifying exam with 15‒25 questions for the Cisco CCNP certification. The TSHOOT 300-135 exam certifies that the successful candidate has the knowledge and skills necessary to:

Plan and perform regular maintenance on complex enterprise routed and switched networks

Use technology-based practices and a systematic ITIL-compliant approach to perform network troubleshooting

The following topics are general guidelines for the content that is likely to be included on the exam. However, other related topics may also appear on any specific version of the exam. To better reflect the contents of the exam and for clarity, the following guidelines may change at any time without notice.

5% 1.0 Network Principles

1.1 Use Cisco IOS troubleshooting tools 1.1.a Debug, conditional debug

1.1.b Ping and trace route with extended options 1.2 Apply troubleshooting methodologies

1.2.a Diagnose the root cause of networking issues (analyze symptoms, identify and describe root cause)

1.2.b Design and implement valid solutions 1.2.c Verify and monitor resolution


2.1 Troubleshoot switch administration 2.1.a SDM templates 2.1.b Managing MAC address table

2.1.c Troubleshoot Err-disable recovery

2.2 Troubleshoot Layer 2 protocols 2.2.a CDP, LLDP 2.2.b UDLD

2.3 Troubleshoot VLANs 2.3.a Access ports 2.3.b VLAN database 2.3.c Normal, extended VLAN, voice VLAN

2.4 Troubleshoot trunking 2.4.a VTPv1, VTPv2, VTPv3, VTP pruning

2.4.b dot1Q

















2.4.c Native VLAN 2.4.d Manual pruning

2.5 Troubleshoot EtherChannels 2.5.a LACP, PAgP, manual 2.5.b Layer 2, Layer 3 2.5.c Load balancing 2.5.d EtherChannel misconfiguration guard

2.6 Troubleshoot spanning tree 2.6.a PVST+, RPVST +, MST 2.6.b Switch priority, port priority, path cost, STP timers 2.6.c PortFast, BPDUguard, BPDUfilter 2.6.d Loopguard, Rootguard

2.7 Troubleshoot other LAN switching technologies 2.7.a SPAN, RSPAN

2.8 Troubleshoot chassis virtualization and aggregation technologies

2.8.a Stackwise

40% 3.0 Layer 3 Technologies 3.1 Troubleshoot IPv4 addressing and subnetting

3.1.a Address types (Unicast, broadcast, multicast, and VLSM) 3.1.b ARP 3.1.c DHCP relay and server 3.1.d DHCP protocol operations

3.2 Troubleshoot IPv6 addressing and subnetting

3.2.a Unicast 3.2.b EUI-64 3.2.c ND, RS/RA 3.2.d Autoconfig (SLAAC) 3.2.e DHCP relay and server 3.2.f DHCP protocol operations

3.3 Troubleshoot static routing

3.4 Troubleshoot default routing

3.5 Troubleshoot administrative distance

3.6 Troubleshoot passive interfaces

3.7 Troubleshoot VRF lite 3.8 Troubleshoot filtering with any protocol

















3.9 Troubleshoot between any routing protocols or routing sources 3.10 Troubleshoot manual and autosummarization with any routing protocol 3.11 Troubleshoot policy-based routing 3.12 Troubleshoot suboptimal routing 3.13 Troubleshoot loop prevention mechanisms

3.13.a Route tagging, filtering 3.13.b Split-horizon 3.13.c Route poisoning

3.14 Troubleshoot RIPv2

3.15 Troubleshoot EIGRP neighbor relationship and authentication 3.16 Troubleshoot loop free path selection

3.16.a RD, FD, FC, successor, feasible successor

3.17 Troubleshoot EIGPR operations 3.17.a Stuck in active

3.18 Troubleshoot EIGRP stubs 3.19 Troubleshoot EIGRP load balancing

3.19.a Equal cost 3.19.b Unequal cost

3.20 Troubleshoot EIGRP metrics

3.21 Troubleshoot EIGRP for IPv6 3.22 Troubleshoot OSPF neighbor relationship and authentication 3.23 Troubleshoot network types, area types, and router types

3.23.a Point-to-point, multipoint, broadcast, nonbroadcast 3.23.b LSA types, area type: backbone, normal, transit, stub, NSSA, totally stub 3.23.c Internal router, backbone router, ABR, ASBR 3.23.d Virtual link

3.24 Troubleshoot OSPF path preference

3.25 Troubleshoot OSPF operations 3.26 Troubleshoot OSPF for IPv6 3.27 Troubleshoot BGP peer relationships and authentication

















3.27.a Peer group 3.27.b Active, passive 3.27.c States and timers

3.28 Troubleshoot eBGP

3.28.a eBGP 3.28.b 4-byte AS number 3.28.c Private AS

5% 4.0 VPN Technologies

4.1 Troubleshoot GRE

5% 5.0 Infrastructure Security 5.1 Troubleshoot IOS AAA using local database

5.2 Troubleshoot device access control

5.2.a Lines (VTY, AUX, console) 5.2.b Management plane protection 5.2.c Password encryption

5.3 Troubleshoot router security features

5.3.a IPv4 access control lists (standard, extended, time-based) 5.3.b IPv6 traffic filter 5.3.c Unicast reverse path forwarding


6.1 Troubleshoot device management 6.1.a Console and VTY

6.1.b Telnet, HTTP, HTTPS, SSH, SCP 6.1.c (T)FTP

6.2 Troubleshoot SNMP

6.2.a v2 6.2.b v3

6.3 Troubleshoot logging

6.3.a Local logging, syslog, debugs, conditional debugs 6.3.b Timestamps

6.4 Troubleshoot Network Time Protocol(NTP) 6.4.a NTP master, client, version 3, version 4 6.4.b NTP authentication 6.5 Troubleshoot IPv4 and IPv6 DHCP 6.5.a DHCP client, IOS DHCP server, DHCP relay 6.5.b DHCP options (describe)

















6.6 Troubleshoot IPv4 Network Address Translation (NAT) 6.6.a Static NAT, Dynamic NAT, PAT 6.7 Troubleshoot SLA architecture 6.8 Troubleshoot tracking objects 6.8.a Tracking objects 6.8.b Tracking different entities (for example, interfaces, IPSLA results)

702, Somdatt Chambers - II, Bhikaji Cama Place, New Delhi - 110066 (INDIA)

















Cisco Certified Network Associate Version 2...

Documents

Transcript of Cisco Certified Network Associate Version 2...