Cisco 12K Config Guide

8/9/2019 Cisco 12K Config Guide

1/443


2/443

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL

STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT

WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT

SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE

OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCBs public

domain version of the UNIX operating system. All rights reserved. Copyright 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED AS IS WITH

ALL FAULTS. CISCO AND THE ABOVE-NAMED SUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT

LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF

DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFIT S OR LOSS OR DAMAGE TO DATA ARISING OUT OF TH E USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISC O

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING,

WITHOUT LIMITATION, LOST PROFIT S OR LOSS OR DAMAGE TO DATA ARISING OUT OF TH E USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISC O

OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

CCDE, CCENT, Cisco Eos, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TeleP resence, Cisco WebEx, the Cisco logo, DCE, and Welcome to the Human Network

are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To

You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems,

Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing,

FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace,

MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet,

Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc.

and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship

between Cisco and any other company. (0809R)

Cisco 12000 Series Router SIP and SPA Software Configuration Guide (Cisco IOS)

Copyright 2008 Cisco Systems, Inc. All rights reserved.


3/443


4/443

Contents

iv


Release 12.0(33)S, OL-8832-01, Rev. C9

SPA Interface Processors 2-1

Shared Port Adapters 2-2

SFP and XFP Optics Modules 2-3

SIP and SPA Compatibility 2-5

Overview of the Cisco 12000 Series Router SIPs 3-1

Release History 3-1

Supported Features 3-2

Cisco 12000 SIP-401, Cisco 12000 SIP-501, Cisco 12000 SIP-600, and Cisco 12000 SIP-601

Features 3-2

Cisco 12000 SIP-400 Features 3-4

Key Features 3-4

Supported MIBs 3-6

Displaying the SPA Hardware Type 3-9

Example of the show gsr Command 3-10

Gigabit Ethernet Shared Port Adapters

Overview of the Gigabit Ethernet SPAs 4-1

Release History 4-1


Gigabit Ethernet SPA Features 4-2

Supported MIBs 4-3

SPA Architecture 4-4

Path of a Packet in the Ingress Direction 4-4

Path of a Packet in the Egress Direction 4-4


Example of the show interfaces Command 4-5

Configuring the Fast Ethernet and Gigabit Ethernet SPAs 5-1

Configuration Tasks 5-1

Required Configuration Tasks 5-2Specifying the Interface Address 5-4

Modifying the MAC Address on the Interface 5-5

Gathering MAC Address Accounting Statistics 5-6

Configuring HSRP 5-6

Modifying the Interface MTU Size 5-7

Configuring the Encapsulation Type 5-9

Configuring Autonegotiation on an Interface 5-9

Configuring a Subinterface on a VLAN 5-10


5/443

Contents

v


Release 12.0(33)S, OL-8832-01, Rev. C9

Configuring Flow Control Support on the Link 5-11

Saving the Configuration 5-12

Shutting Down and Restarting an Interface on a SPA 5-12

Verifying the Interface Configuration 5-12Verifying Per-Port Interface Status 5-13

Configuration Examples 5-14

Basic Interface Configuration Example 5-14

MAC Address Configuration Example 5-15

MTU Configuration Example 5-15

VLAN Configuration Example 5-16

Configuring Dense Wavelength Division Multiplexing Controllers on Cisco IOS Software 5-16

Contents 5-17

Prerequisites for Configuring DWDM Controller Interfaces 5-17

Information About the DWDM Controllers 5-17

How to Configure DWDM Controllers 5-18

Configuring the Optical Parameters 5-18

Configuring G.709 Parameters 5-20

Examples 5-21

Additional References 5-21

Standards 5-22

MIBs 5-22

RFCs 5-22

Technical Assistance 5-22

Troubleshooting the Gigabit Ethernet SPA 6-1

General Troubleshooting Information 6-1

Using show Commands 6-2

Performing Basic Interface Troubleshooting 6-2

Verifying the Interface is Up 6-4

Verifying the Line Protocol is Up 6-5

Verifying Output Hang Status 6-5

Verifying the CRC Counter 6-5

Verifying Late Collisions 6-5

Verifying the Carrier Signal 6-5

Understanding SPA Automatic Recovery 6-6

When Automatic Recovery Occurs 6-6

If Automatic Recovery Fails 6-6

Configuring the Interface for Internal Loopback 6-7

Configuring the Interface for Internal Loopback 6-7


6/443

Contents

vi


Release 12.0(33)S, OL-8832-01, Rev. C9

Configuring the Interface for External Loopback 6-7

Verifying Loopback Status 6-7

Using the Cisco IOS Event Tracer to Troubleshoot Problems 6-8

Preparing for Online Insertion and Removal of a SPA 6-8Cleaning Optics 6-8

Command Summary for Gigabit Ethernet SPAs 7-1

Serial Shared Port Adapters

Overview of the Serial SPAs 8-1

Release History 8-1


SIP-400 Features 8-2

SPA Features 8-2

Restrictions 8-4

Supported MIBs 8-4


Example of the show interface Command 8-6

Configuring the 2-Port and 4-Port Channelized T3 SPA 9-1


Required Configuration Tasks 9-2

Specifying the Interface Address on a SPA 9-7

Optional Configurations 9-8


Verifying the Interface Configuration 9-18

Verifying Per-Port Interface Status 9-18


DSU Configuration Example 9-21

MDL Configuration Example 9-21

Encapsulation Configuration Example 9-21Framing - Unchannelized Mode Configuration Example 9-22

Facility Data Link Configuration Example 9-22

Scrambling Configuration Example 9-22

Configuring the 2-Port and 4-Port T3/E3 SPAs 10-1





7/443

Contents

vii


Release 12.0(33)S, OL-8832-01, Rev. C9




Verifying Per-Port Interface Status 10-18Configuration Examples 10-20

DSU Configuration Example 10-21

MDL Configuration Example 10-21

Encapsulation Configuration Example 10-21

Framing - Unchannelized Mode Configuration Example 10-22


Scrambling Configuration Example 10-22

Configuring the 8-Port Channelized T1/E1 SPA 11-1









Framing and Encapsulation Configuration Example 11-19

CRC Configuration Example 11-19


MLPPP Configuration Example 11-20

MFR Configuration Example 11-21

Invert Data on the T1/E1 Interface Example 11-22

Configuring the 1-Port Channelized OC-3/STM-1 SPA 12-1



Selection of Physical Port and Controller configuration 12-2





Command Summary for Serial SPAs 13-1

Packet over SONET Shared Port Adapters


8/443

Contents

viii


Release 12.0(33)S, OL-8832-01, Rev. C9

Overview of the POS SPAs 14-1

Release History 14-1

POS Technology Overview 14-2

Supported Features 14-3SONET/SDH Compliance Features 14-3

SONET/SDH Error, Alarm, and Performance Monitoring Features 14-4

SONET/SDH Synchronization Features 14-4

WAN Protocol Features 14-5

Network Management Features 14-5

Restrictions 14-5

Supported MIBs 14-7

SPA Architecture 14-8

1-Port OC-192c/STM-64 POS/RPR XFP SPA Architecture 14-8

1-Port OC-192c/STM-64 POS/RPR SPA and 1-Port OC-192c/STM-64 POS/RPR XFP SPA

Architecture 14-9

2-Port OC-48c/STM-16 POS SPA Architecture 14-11


Example of the show interfaces Command 14-12

Example of the show diags Command 14-13

Example of the show controllers Command 14-14

Configuring the POS SPAs 15-1




Modifying the Interface MTU Size 15-4

Modifying the POS Framing 15-5

Modifying the Keepalive Interval 15-7

Modifying the CRC Size 15-7

Modifying the Clock Source 15-8

Modifying SONET Payload Scrambling 15-9

Configuring the Encapsulation Type 15-10

Configuring APS 15-11

Configuring POS Alarm Trigger Delays 15-12

Configuring SDCC 15-15

Configuring Dynamic Packet Transport Features 15-16


Shutting Down and Restarting an Interface on a SPA 15-22



9/443


10/443

Contents

x


Release 12.0(33)S, OL-8832-01, Rev. C9


11/443

F I G U R E S

xi


Release 12.0(33)S, OL-8832-01, Rev. C9

Figure 2-1 Single-height and Double-height SPA Sizes 2

Figure 2-2 Horizontal and Vertical Chassis Slot Orientation for SPAs 2

Figure 5-1 Slot, Subslot, and Port Locations for the Cisco 10-port Gigabit Ethernet SPA and the 1-Port 10-Gigabit EthernetSPA. 5

Figure 5-2 OTN Optical Channel Structure 17

Figure 14-1 1-Port OC-192c/STM-64 POS/RPR XFP SPA Architecture 8

Figure 14-2 1-Port OC-192c/STM-64 POS/RPR XFP SPA Architecture 9

Figure 14-3 2-Port OC-48c/STM-16 POS SPA Architecture 11

Figure 15-1 Basic APS Configuration 28


12/443

Figures

xii


Release 12.0(33)S, OL-8832-01, Rev. C9


13/443

T A B L E S

xiii


Release 12.0(33)S, OL-8832-01, Rev. C9

Table 1 Document Change History Table xv

Table 1-1 Keyboard Shortcuts 5

Table 1-2 History Substitution Commands 5

Table 1-3 Accessing and Exiting Command Modes 6

Table 1-4 How to Find Command Options 8

Table 2-1 SFP Modules 3

Table 2-2 SPA Optics Compatibility 3Table 2-3 SIP and SPA Compatibility on the Cisco 12000 Series Router 5

Table 3-1 SPA Hardware Descriptions in show Commands 10

Table 4-1 Release History for Ethernet SPAs 1


Table 5-1 Slot and Port Locations for the Gigabit Ethernet SPAs 5

Table 6-1 Basic Interface Troubleshooting Steps 3

Table 7-1 Command Summary 1


Table 13-1 Command Summary 1

Table 14-1 POS Feature Compatibility and Restrictions by SIP and SPA Combination 6


Table 16-1 Command Summary for POS SPAs 1

Table 17-1 FPD Release History 1

Table 18-1 FPD Command Summary 1

Table 19-1 Interface Type Keywords 41

Table 19-2 show controllers pos Field Descriptions 73

Table 19-3 show controllers pos pm Field Descriptions 76

Table 19-4 show controllers pos pm Field Descriptions 78

Table 19-5 show controllers serial Field Descriptions 84

Table 19-6 show diag (AIC) Field Descriptions 92

Table 19-7 show diag (AIM-VPN) Field Descriptions 94

Table 19-8 show diag subslot Field Descriptions 94

Table 19-9 Operational Status Field Descriptions 103


14/443

Tables

xiv


Release 12.0(33)S, OL-8832-01, Rev. C9

Table 19-10 show interface sdccField Descriptions 109

Table 19-11 show interfaces posField Descriptions 116

Table 19-12 show interfaces serial Field DescriptionsSynchronous Serial Interface 123

Table 19-13 show interfaces serial Field DescriptionsPA-2JT2 Serial Interface 126

Table 19-14 show interfaces serialField DescriptionsPA-E3 127

Table 19-15 show interfaces serial Field DescriptionsPA-T3 128

Table 19-16 show interfaces serialField DescriptionsCT3IP 129

Table 19-17 show interfaces serialField DescriptionsFrame Relay Interface Queueing and Fragmentation 132

Table 19-18 show interfaces serial Field DescriptionsANSI LMI 134

Table 19-19 show interfaces serial Field DescriptionsLAPB 134

Table 19-20 show interfaces serial Field DescriptionsPPP Encapsulation 135

Table 19-21 show interfaces serial Field DescriptionsSDLC Enabled 136Table 19-22 SDLC Secondary Interface Descriptions 136

Table 19-23 SDLLC Parameter Descriptions 137

Table 19-24 show interfaces serial Field DescriptionsX.25 Enabled 138

Table 19-25 show interfaces serialField DescriptionsAccounting 140

Table 19-26 show interfaces serial Field DescriptionsCisco AS5800 140

Table 19-27 T3/E3 SPACommand Field Descriptions 141

Table 28 Relationship Between duplex and speed Commands 155


15/443

xv


Release 12.0(33)S, OL-8832-01, Rev. C9

Preface

Revised: Release 12.0(33)S, OL-8832-01, Rev. C9

This preface describes the objectives and organization of this document and explains how to find

additional information on related products and services. This preface contains the following sections:

Document Change History, page xv

Objectives, page xvii

Organization, page xviii

Related Documentation, page xix

Document Conventions, page xx

Document Change HistoryTable 1provides a list of the changes to this document.

Table 1 Document Change History Table

Release No. Revision Date Change Summary

12.0(31)S Release

12.0(31)S

April 26, 2005 Initial release and 1st publication. Provides Cisco IOS commands

and configuration procedures for the following SPAs installed in a

Cisco 12000 SIP-400 or a Cisco 12000 SIP-600:

1-Port 10-Gigabit Ethernet SPA

5-Port 10 Gigabit Ethernet SPA

10-Port Gigabit Ethernet SPA

2-Port and 4-Port Clear Channel T3/E3 SPA 2-Port and 4-Port Channelized T3 SPA

1-Port OC-192c/STM-64 POS/RPR SPA

12.0(31)S2 Release

12.0(31)S2

September 22, 2005 Support for the following hardware by the Cisco 12000 SIP-600

was introduced on the Cisco 12000 series router:

2-Port OC-48c/STM-16 POS SPA


16/443


17/443

xvii


Release 12.0(33)S, OL-8832-01, Rev. C9

Preface

ObjectivesThis document describes the configuration and troubleshooting of SPA interface processors (SIPs) and

shared port adapters (SPAs) that are supported on a Cisco 12000 Series Router.

12.0(32)SY6 Release

12.0(32)SY6

May 7, 2008 Added a starting and ending argument for the

command show controllers poson a Cisco 12000 series router or

on a POS Shared Port Adapter.

Command output displays the POS interface details for each of the

time-intervals between the specified range. Command output

changes applicable for Cisco 12000 series router or for a POS

Shared Port Adapter.

12.0(33)S Release

12.0(33)S

April 26, 2007 Support for the following hardware by the Cisco 12000 SIP-600 and

the Cisco 12000 SIP-601 was introduced on the Cisco 12000 series

router:

1-Port 10-Gigabit Ethernet SPA [WAN-PHY]

(SPA-1X10GE-WL-V2)

1-Port 10-Gigabit Ethernet DWDM SPA

(SPA-1X10GE-L-ITUC)

Support for the following hardware by the Cisco 12000 SIP-401,

Cisco 12000 SIP-501 and Cisco 12000 SIP-601 was introduced on

the Cisco 12000 series router:

8-Port Gigabit Ethernet SPA (SPA-8X1GE-V2)

Support for the following hardware by the Cisco 12000 SIP-501 and

Cisco 12000 SIP-601 was introduced on the Cisco 12000 series

router:


Information specific to BERT configuration for the following SPAs

was introduced:

2-Port and 4-Port Channelized T3 SPA

8-Port Channelized T1/E1 SPA

1-Port Channelized OC-3/STM-1 SPA

12.0(33)S2 Release

12.0(33)S2

November 10, 2008 Added following flowcontrol commands supported on Cisco IOS

Release 12.0(33)S2 on Cisco 12000 series router for Engine 5

SIP-401/501/600/601 line card and applicable on GE or FE SPA

interfaces:

show interfaces flowcontrol

flowcontrol bidirectional

no flowcontrol bidirectional

Table 1 Document Change History Table (continued)

Release No. Revision Date Change Summary


18/443

xviii


Release 12.0(33)S, OL-8832-01, Rev. C9

Preface

OrganizationThis document contains the following chapters:

Chapter Title Description

Part 1 Shared Port Adapters Covers IOS Software and SIP and SPA overview.

Chapter 1 Using Cisco IOS Software Provides an introduction to accessing the

command-line interface (CLI) and using the Cisco

IOS Software and related tools.

Chapter 2 SIP and SPA Product Overview Provides an introduction to modular services cards

(SIPs) and shared port adapters (SPAs).

Chapter 3 Overview of the Cisco 12000

Series Router SIPs

Provides an overview of the release history, and

feature and Management Information Base (MIB)

support for the SIPs supported on the Cisco 12000

Series Routers.

Part 2 Gigabit Ethernet Shared Port

Adapters

Covers Gigabit Ethernet SPA Configuration.

Chapter 4 Overview of the Gigabit Ethernet

SPAs



support for the Gigabit Ethernet SPAs on the Cisco

12000 series router.

Chapter 5 Configuring the Fast Ethernet and

Gigabit Ethernet SPAs

Describes how to configure the Gigabit Ethernet

SPAs on the Cisco 12000 Series Router.

Chapter 6 Troubleshooting the

Gigabit Ethernet SPA

This chapter describes techniques that you can use to

troubleshoot the operation of your GigabitEthernet

SPAs.

Chapter 7 Command Summary for Gigabit

Ethernet SPAs

Provides an alphabetical list of the most significant

commands that are needed to configure, monitor, and

maintain the Fast Ethernet and Gigabit Ethernet

shared port adapter (SPA) cards.

Part 3 Serial Shared Port Adapters Covers Serial SPAs.

Chapter 8 Overview of the Serial SPAs Provides an overview of the release history, features,

and MIBs for the 2 and 4-Port T3/E3 SPA and the 2

or 4-Port CT3 SPA.

Chapter 9 Configuring the 2-Port and 4-Port

Channelized T3 SPA

Provides information about configuring the 2-Port

and 4-Port Channelized T3 Shared Port Adapters

(SPAs) on the Cisco 12000 series routers.

Chapter 10 Configuring the 2-Port and 4-Port

T3/E3 SPAs

Provides information about configuring the 2-Port

and 4-Port T3/E3 Shared Port Adapters (SPAs) on the

Cisco 12000 Series routers.

Chapter 13 Command Summary for Serial

SPAs

Provides an alphabetical list of some of the related

commands to configure, monitor, and maintain Serial

SPAs.

Part 4 Packet over SONET Shared Port

Adapters

Covers POS SPAs.


19/443

xix


Release 12.0(33)S, OL-8832-01, Rev. C9

Preface

Related Documentation

This section refers you to other documentation that also might be useful as you configure yourCisco 12000 Series Router. The documentation listed below is available online.

Cisco 12000 Series Router SIP and SPA Hardware Installation Guide


Cross-Platform Release Notes for Cisco IOS Release 12.0 S

Regulatory Compliance and Safety Information for Cisco 12000 Series Routerss

Cisco 12000 Series Router Documentation

As you configure SIPs and SPAs on your Cisco 12000 Series Router, you should also refer to the

following companion publication for important hardware installation information:

Cisco 12000 Series Router SIP and SPA Hardware Installation Guide

Some of the other Cisco 12000 Series Router publications might be useful to you as you configure your

Cisco 12000 Series Router. The following URL provides a wide range of documentation for the various

Cisco 12000 Series Routers and their accompanying field replaceable units (FRUs):

http://www.cisco.com/univercd/cc/td/doc/product/core/cis12000/

Several other publications are also related to the Cisco 12000 Series Router. For a complete reference of

related documentation, refer to the various roadmap documents located at the following URL:

Chapter 14 Chapter 14, Overview of the POS

SPAs



support for the Packet over SONET (POS) SPAs on

the Cisco 12000 Series Router.

Chapter 15 Configuring the POS SPAs Provides information about configuring the Packet

over SONET (POS) SPAs on the Cisco 12000

SIP-600 series routers.

Chapter 16 Command Summary for the POS

SPAs

Provides an alphabetical list of some of the related

commands to configure, monitor, and maintain POS

SPAs.

Part 5 Field-Programmable Devices Covers FPDs.

Chapter 17 Upgrading Field-Programmable

Devices

Provides information about upgrading the

Field-Programmable Gate Array (FPGA) on the

Cisco 12000 Series Router.

Chapter 18 Command Summary for FPDs Provides an alphabetical list of some of the relatedcommands to configure, monitor, and upgrade FPD

images for SPAs on the Cisco 12000 Series Router.

Chapter 19 SIP and SPA Command Reference Describes Cisco IOS software command reference

information including syntax, usage guidelines, and

examples for all new and modified commands for

SPAs on a Cisco 12000 Series Router.

Chapter Title Description
http://www.cisco.com/univercd/cc/td/doc/product/core/cis12000/http://www.cisco.com/univercd/cc/td/doc/product/core/cis12000/


20/443

xx


Release 12.0(33)S, OL-8832-01, Rev. C9

Preface

http://www.cisco.com/univercd/cc/td/doc/product/core/cis12000/roadmap/

Cisco IOS Software Publications

Your router, switch, or gateway and the Cisco IOS software running on it contain extensive features. Youcan find documentation for Cisco IOS software features at the following URL:

http://www.cisco.com/univercd/cc/td/doc/product/software/

Cisco IOS Release 12.0 S Software Publications

Documentation for Cisco IOS Release 12.0 S, including release notes and system error messages, can be

found at the following URL:

http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/

Document ConventionsWithin the SIP and SPA software configuration guides, the term router is generally used to refer to a

variety of Cisco products (for example, routers, access servers, and switches). Routers, access servers,

and other networking devices that support Cisco IOS software are shown interchangeably within

examples. These products are used only for illustrative purposes; that is, an example that shows one

product does not necessarily indicate that other products are not supported.

This documentation uses the following conventions:

Command syntax descriptions use the following conventions:

Convention Description

^ or Ctrl The and Ctrl symbols represent the Control key. For example, the key combination D or Ctrl-Dmeans hold down the Control key while you press the D key. Keys are indicated in capital letters but

are not case sensitive.

string A string is a nonquoted set of characters shown in italics. For example, when setting an SNMP

communitystring topublic, do not use quotation marks around the string or the string will include the

quotation marks.


bold Bold text indicates commands and keywords that you enter literally as shown.italics Italic text indicates arguments for which you supply values.

[x] Square brackets enclose an optional element (keyword or argument).

| A vertical line indicates a choice within an optional or required set of keywords or arguments.

[x | y] Square brackets enclosing keywords or arguments separated by a vertical l ine indicate an optional

choice.

{x | y} Braces enclosing keywords or arguments separated by a vertical line indicate a required choice.
http://www.cisco.com/univercd/cc/td/doc/product/core/cis12000/roadmap/http://www.cisco.com/univercd/cc/td/doc/product/software/ios120/index.htmhttp://www.cisco.com/univercd/cc/td/doc/product/software/ios120/index.htmhttp://www.cisco.com/univercd/cc/td/doc/product/core/cis12000/roadmap/


21/443

xxi


Release 12.0(33)S, OL-8832-01, Rev. C9

Preface

Nested sets of square brackets or braces indicate optional or required choices within optional or required

elements. For example:

Examples use the following conventions:

The following conventions are used to attract the attention of the reader:

Caution Means reader be careful. In this situation, you might do something that could result in equipment

damage or loss of data.

Note Means reader take note. Notes contain helpful suggestions or references to materials not contained

in this manual.

Obtaining Documentation and Submitting a Service RequestFor information on obtaining documentation, submitting a service request, and gathering additional

information, see the monthly Whats New in Cisco Product Documentation, which also lists all new and

revised Cisco technical documentation, at:

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the Whats New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed

and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free

service and Cisco currently supports RSS version 2.0.


[x {y | z}] Braces and a vertical line within square brackets indicate a required choice within an optional element.


screen Examples of information displayed on the screen are set in Courier font.

bold screen Examples of text that you must enter are set in Courier bold font.

< > Angle brackets enclose text that is not printed to the screen, such as passwords.

! An exclamation point at the beginning of a line indicates a comment line. (Exclamation points are also

displayed by the Cisco IOS software for certain processes.)

[ ] Square brackets enclose default responses to system prompts.
http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.htmlhttp://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html


22/443

xxii


Release 12.0(33)S, OL-8832-01, Rev. C9

Preface


23/443

P A R T 1

Shared Port Adapters


24/443


25/443

C H A P T E R

1-1


Release 12.0(33)S, OL-8832-01, Rev. C9

1Using Cisco IOS SoftwareThis chapter provides useful information as you prepare to configure a shared port adapter (SPA) using

the Cisco IOS software. It includes the following sections:

Accessing the CLI Using a Router Console, page 1-1

Using Keyboard Shortcuts, page 1-4

Using the History Buffer to Recall Commands, page 1-5

Understanding Command Modes, page 1-5

Getting Help, page 1-7

Using the no and default Forms of Commands, page 1-10

Saving Configuration Changes, page 1-11

Filtering Output from the show and more Commands, page 1-11

Finding Support Information for Platforms and Cisco IOS Software Images, page 1-12

Accessing the CLI Using a Router ConsoleThis section describes how to access the command-line interface (CLI) using a directly-connected

console or by using Telnet to obtain a remote console:

Accessing the CLI Using a Directly-Connected Console, page 1-1

Accessing the CLI from a Remote Console Using Telnet, page 1-3

Accessing the CLI From a Remote Console Using a Modem, page 1-4

For more detailed information about configuring and accessing a router through various services, refer

to the Cisco IOS Terminal Services Configuration Guideand Cisco IOS Terminal Services Command

Referencepublications.

For more information about making the console cable connections, refer to the Cisco 12000 Series

Router SIP and SPA Hardware Installation Guide.

Accessing the CLI Using a Directly-Connected Console

This section describes how to connect to the console port on the router and use the console interface to

access the CLI.


26/443

1-2


Release 12.0(33)S, OL-8832-01, Rev. C9

Chapter 1 Using Cisco IOS Software

Accessing the CLI Using a Router Console

Connecting to the Console Port

Before you can use the console interface on the router using a terminal or PC, perform the following

steps:

Step 1 Configure your terminal emulation software with the following settings:

9600 bits per second (bps)

8 data bits

No parity

2 stop bits

Note These are the default serial communication parameters on the router. For information about how to

change those defaults to meet the requirements of your terminal or host, refer to the Cisco IOS Terminal

Services Configuration Guide.

Step 2 Connect a terminal or PC to the console port using a rollover cable.

To make this connection, attach one end of an RJ-45 to RJ-45 rollover cable to the router console port.

Attach the other end of the cable to an ASCII terminal or a PC running terminal emulation software. The

ASCII terminal or PC port might require an RJ-45-to-DB-9 or an RJ-45-to-DB-25 adapter.

Using the Console Interface

To access the CLI using the console interface, complete the following steps:

Step 1 After you attach the terminal hardware to the console port on the router (and have configured your

terminal emulation software with the proper settings), the following prompt appears:

Press Return for Console prompt

Step 2 Press Returnto enter user EXEC configuration mode. The following prompt appears:

Router>

Step 3 From user EXEC configuration mode, enter the enablecommand as shown in the following example:

Router> enable

Step 4 At the password prompt, enter your systems password. The following example shows entry of the

password called enablepass:

Password:

Step 5 When the enable password is accepted, the privileged EXEC configuration mode prompt appears:

Router#

Step 6 You now have access to the CLI in privileged EXEC configuration mode and you can enter the necessary

commands to complete your desired tasks.

Step 7 To exit the console session, enter the quitcommand as shown in the following example:

Router# quit


27/443

1-3


Release 12.0(33)S, OL-8832-01, Rev. C9


Accessing the CLI Using a Router Console

Accessing the CLI from a Remote Console Using Telnet

This section describes how to connect to the console interface on a router using Telnet to access the CLI.

Preparing to Connect to the Router Console Using Telnet

Before you can access the router remotely using Telnet from a TCP/IP network, you need to configure

the router to support virtual terminal lines (vtys) using the line vtyglobal configuration command. You

also should configure the vty lines to require login and specify a password.

Note To prevent disabling login on the line, be careful that you specify a password with the password

command when you configure the login line configuration command. If you are using authentication,

authorization, and accounting (AAA), you should configure the login authenticationline configurationcommand. To prevent disabling login on the line for AAA authentication when you configure a list with

the login authenticationcommand, then you must also configure that list using the aaa authentication

loginglobal configuration command. For more information about AAA services, refer to the Cisco IOS

Security Configuration Guideand Cisco IOS Security Command Reference publications.

In addition, before you can make a Telnet connection to the router you must have a valid host name for

the router, or have an IP address configured on the router. For more information about requirements for

connecting to the router using Telnet, information about customizing your Telnet services, and using

Telnet key sequences, refer to the Cisco IOS Terminal Services Configuration Guide.

Using Telnet to Access a Console InterfaceTo access a console interface using Telnet, complete the following steps:

Step 1 From your terminal or PC, enter one of the following commands:

connecthost[port] [keyword]

telnethost[port] [keyword]

where hostis the router host name or an IP address, portis a decimal port number (23 is the default),

and keywordis a supported keyword. For more information, refer to the Cisco IOS Terminal Services

Command Reference.

Note If you are using an access server, then you also will need to specify a valid port number with the host

name or IP address, such as telnet 172.20.52.40 2003.

The following example shows the telnet command to connect to the router named Router:

unix_host% telnet RouterTrying 172.20.52.40...Connected to 172.20.52.40.Escape character is '^]'.unix_host% connect


28/443

1-4


Release 12.0(33)S, OL-8832-01, Rev. C9


Using Keyboard Shortcuts

Step 2 At the password prompt, enter your login password. The following example shows entry of the password

called mypass:

User Access Verification

Password:

Note If no password has been configured, press Return.

Step 3 From user EXEC configuration mode, enter the enablecommand as shown in the following example:

Router> enable

Step 4 When the enable password is accepted, the privileged EXEC configuration mode prompt appears:

Router#

Step 5 You now have access to the CLI in privileged EXEC configuration mode and you can enter the necessary

commands to complete your desired tasks.

Step 6 To exit the Telnet session, use the exitor logoutcommand as shown in the following example:

Router# logout

Accessing the CLI From a Remote Console Using a Modem

To access the router remotely using a modem through an asynchronous connection, you need to

configure the AUX port and attach a modem to it.

For more information about making a modem connection using the AUX port on the Cisco 12000 Series

Router, refer to the Cisco 12000 Series Router SIP and SPA Hardware Installation Guide.

For detailed guidelines on making a connection to the router using a modem, and using reverse Telnet,

refer to Configuring a Modem on the AUX Port for EXEC Dialin Connectivity located at the following

URL:

http://www.cisco.com/warp/public/471/mod-aux-exec.html

Using Keyboard ShortcutsCommands are not case sensitive. You can abbreviate commands and parameters if the abbreviations

contain enough letters to be different from any other currently available commands or parameters. You

can scroll through the last 20 commands stored in the history buffer, and enter or edit the command atthe prompt.
http://www.cisco.com/warp/public/471/mod-aux-exec.htmlhttp://www.cisco.com/warp/public/471/mod-aux-exec.html


29/443

1-5


Release 12.0(33)S, OL-8832-01, Rev. C9


Using the History Buffer to Recall Commands

Table 1-1lists the keyboard shortcuts for entering and editing commands.

Using the History Buffer to Recall CommandsThe history buffer stores the last 20 commands you entered. History substitution allows you to access

these commands without retyping them, by using special abbreviated commands.

Table 1-2lists the history substitution commands.

Understanding Command ModesYou use the CLI to access Cisco IOS software. Because the CLI is divided into many different modes,

the commands available to you at any given time depend on the mode that you are currently in. Entering

a question mark (?) at the CLI prompt allows you to obtain a list of commands available for each

command mode.

When you log in to the CLI, you are in user EXEC mode. User EXEC mode contains only a limited

subset of commands. To have access to all commands, you must enter privileged EXEC mode, normally

by using a password. From privileged EXEC mode you can issue any EXEC commanduser or

Table 1-1 Keyboard Shortcuts

Keystrokes Purpose

Press Ctrl-Borpress the left arrow key1

1. The arrow keys function only on ANSI-compatible terminals such as VT100s.

Move the cursor back one character

Press Ctrl-For

press the right arrow key1Move the cursor forward one character

Press Ctrl-A Move the cursor to the beginning of the command line

Press Ctrl-E Move the cursor to the end of the command line

PressEsc B Move the cursor back one word

PressEsc F Move the cursor forward one word

Table 1-2 History Substitution Commands

Command Purpose

Ctrl-P or the up arrow key.1

1. The arrow keys function only on ANSI-compatible terminals such as VT100s.

Recall commands in the history buffer, beginning

with the most recent command. Repeat the keysequence to recall successively older commands.

Ctrl-N or the down arrow key.1 Return to more recent commands in the history

buffer after recalling commands with Ctrl-P or the

up arrow key. Repeat the key sequence to recall

successively more recent commands.

Router# show history While in EXEC mode, list the last several

commands you have just entered.


30/443

1-6


Release 12.0(33)S, OL-8832-01, Rev. C9


Understanding Command Modes

privileged modeor you can enter global configuration mode. Most EXEC commands are one-time

commands. For example, showcommands show important status information, and clearcommands

clear counters or interfaces. The EXEC commands are not saved when the software reboots.

Configuration modes allow you to make changes to the running configuration. If you later save the

running configuration to the startup configuration, these changed commands are stored when the

software is rebooted. To enter specific configuration modes, you must start at global configuration mode.From global configuration mode, you can enter interface configuration mode and a variety of other

modes, such as protocol-specific modes.

ROM monitor mode is a separate mode used when the Cisco IOS software cannot load properly. If a valid

software image is not found when the software boots or if the configuration file is corrupted at startup,

the software might enter ROM monitor mode.

Table 1-3describes how to access and exit various common command modes of the Cisco IOS software.

It also shows examples of the prompts displayed for each mode.

For more information on command modes, refer to the Using the Command-Line Interface chapter in

the Cisco IOSConfiguration Fundamentals and Network Management Configuration Guide.

Table 1-3 Accessing and Exiting Command Modes

CommandMode Access Method Prompt Exit Method

User EXEC Log in. Router> Use the logoutcommand.

Privileged

EXEC

From user EXEC mode,

use the enableEXEC

command.

Router# To return to user EXEC mode, use the disable

command.

Global

configuration

From privileged EXEC

mode, use theconfigure

terminal privileged

EXEC command.

Router(config)# To return to privileged EXEC mode from global

configuration mode, use the exitor endcommand.

Interface

configuration

From global

configuration mode,specify an interface using

an interfacecommand.

Router(config-if)# To return to global configuration mode, use the exit

command.To return to privileged EXEC mode, use the end

command.

ROM monitor From privileged EXEC

mode, use the reload

EXEC command. Press

the Breakkey during the

first 60 seconds while the

system is booting.

> To exit ROM monitor mode, use the continue

command.


31/443

1-7


Release 12.0(33)S, OL-8832-01, Rev. C9


Getting Help

Getting HelpEntering a question mark (?) at the CLI prompt displays a list of commands available for each command

mode. You can also get a list of keywords and arguments associated with any command by using the

context-sensitive help feature.

To get help specific to a command mode, a command, a keyword, or an argument, use one of the

following commands:

Example: How to Find Command Options

This section provides an example of how to display syntax for a command. The syntax can consist of

optional or required keywords and arguments. To display keywords and arguments for a command, enter

a question mark (?) at the configuration prompt or after entering part of a command followed by a space.

The Cisco IOS software displays a list and brief description of available keywords and arguments. For

example, if you were in global configuration mode and wanted to see all the keywords or arguments for

the arapcommand, you would type arap ?.

The symbol in command help output stands for carriage return. On older keyboards, the carriage

return key is the Return key. On most modern keyboards, the carriage return key is the Enter key. The

symbol at the end of command help output indicates that you have the option to press Enterto

complete the command and that the arguments and keywords in the list preceding the symbol are

optional. The symbol by itself indicates that no more arguments or keywords are available and that

you must press Enterto complete the command.

Table 1-4shows examples of how you can use the question mark (?)to assist you in entering commands.

The table steps you through configuring an IP address on a serial interface on a Cisco 7206 router that

is running Cisco IOS Release 12.0(3).

Command Purpose

help Provides a brief description of the help system in any command mode.

abbreviated-command-entry? Provides a list of commands that begin with a particular character string. (No space

between command and question mark.)

abbreviated-command-entry Completes a partial command name.

? Lists all commands available for a particular command mode.

command? Lists the keywords or arguments that you must enter next on the command line.(Space between command and question mark.)


32/443

1-8


Release 12.0(33)S, OL-8832-01, Rev. C9


Getting Help

Table 1-4 How to Find Command Options

Command Comment

Router> enablePassword:

Router#

Enter the enablecommand and

password to access privileged EXECcommands. You are in privileged EXEC

mode when the prompt changes to

Router#.

Router# configure terminalEnter configuration commands, one per line. End with CNTL/Z.Router(config)#

Enter the configure terminalprivileged

EXEC command to enter global

configuration mode. You are in global

configuration mode when the prompt

changes to Router(config)#.

Router(config)# interface serial ? Serial interface numberRouter(config)# interface serial 4 ? /

Router(config)# interface serial 4/ ? Serial interface numberRouter(config)# interface serial 4/0 ?Router(config)# interface serial 4/0Router(config-if)#

Enter interface configuration mode by

specifying the serial interface that you

want to configure using the interface

serialglobal configuration command.

Enter ? to display what you must enter

next on the command line. In this

example, you must enter the serial

interface slot number and port number,

separated by a forward slash.

When the symbol is displayed, you

can press Enterto complete the

command.

You are in interface configuration mode

when the prompt changes to

Router(config-if)#.


33/443

1-9


Release 12.0(33)S, OL-8832-01, Rev. C9


Getting Help

Router(config-if)# ?Interface configuration commands: . . . ip Interface Internet Protocol config commands keepalive Enable keepalive lan-name LAN Name command llc2 LLC2 Interface Subcommands load-interval Specify interval for load calculation for an interface locaddr-priority Assign a priority group logging Configure logging for interface loopback Configure internal loopback on an interface mac-address Manually set interface MAC address mls mls router sub/interface commands mpoa MPOA interface configuration commands

mtu Set the interface Maximum Transmission Unit (MTU) netbios Use a defined NETBIOS access list or enable name-caching no Negate a command or set its defaults nrzi-encoding Enable use of NRZI encoding ntp Configure NTP . . .Router(config-if)#

Enter ? to display a list of all the

interface configuration commands

available for the serial interface. Thisexample shows only some of the

available interface configuration

commands.

Router(config-if)# ip ?Interface IP configuration subcommands: access-group Specify access control for packets accounting Enable IP accounting on this interface address Set the IP address of an interface

authentication authentication subcommands bandwidth-percent Set EIGRP bandwidth limit broadcast-address Set the broadcast address of an interface cgmp Enable/disable CGMP directed-broadcast Enable forwarding of directed broadcasts dvmrp DVMRP interface commands hello-interval Configures IP-EIGRP hello interval helper-address Specify a destination address for UDP broadcasts hold-time Configures IP-EIGRP hold time . . .Router(config-if)#ip

Enter the command that you want to

configure for the interface. This

example uses the ipcommand.


next on the command line. This example

shows only some of the available

interface IP configuration commands.

Table 1-4 How to Find Command Options (continued)

Command Comment


34/443

1-10


Release 12.0(33)S, OL-8832-01, Rev. C9


Using the no and default Forms of Commands

Using the no and default Forms of CommandsAlmost every configuration command has a noform. In general, use the noform to disable a function.

Use the command without the nokeyword to reenable a disabled function or to enable a function that is

disabled by default. For example, IP routing is enabled by default. To disable IP routing, use the no ip

routingcommand; to reenable IP routing, use the ip routingcommand. The Cisco IOS software

command referencepublications provide the complete syntax for the configuration commands and

describe what the noform of a command does.

Configuration commands can also have a defaultform, which returns the command settings to the

default values. Most commands are disabled by default, so in such cases using the defaultform has the

same result as using the noform of the command. However, some commands are enabled by default and

Router(config-if)# ip address ? A.B.C.D IP address negotiated IP Address negotiated over PPPRouter(config-if)# ip address

Enter the command that you want to

configure for the interface. This

example uses the ip addresscommand.



example, you must enter an IP address

or the negotiatedkeyword.

A carriage return () is not

displayed; therefore, you must enter

additional keywords or arguments to

complete the command.

Router(config-if)#ip address 172.16.0.1 ? A.B.C.D IP subnet maskRouter(config-if)#ip address 172.16.0.1

Enter the keyword or argument that you

want to use. This example uses the

172.16.0.1 IP address.Enter ?to display what you must enter


example, you must enter an IP subnet

mask.

A is not displayed; therefore, you

must enter additional keywords or

arguments to complete the command.

Router(config-if)# ip address 172.16.0.1 255.255.255.0 ? secondary Make this IP address a secondary address Router(config-if)#ip address 172.16.0.1 255.255.255.0

Enter the IP subnet mask. This example

uses the 255.255.255.0 IP subnet mask.

Enter ?to display what you must enter

next on the command line. In thisexample, you can enter the secondary

keyword, or you can press Enter.

A is displayed; you can press

Enter to complete the command, or you

can enter another keyword.

Router(config-if)#ip address 172.16.0.1 255.255.255.0Router(config-if)#

In this example, Enteris pressed to

complete the command.

Table 1-4 How to Find Command Options (continued)

Command Comment


35/443

1-11


Release 12.0(33)S, OL-8832-01, Rev. C9


Saving Configuration Changes

have variables set to certain default values. In these cases, the defaultform of the command enables the

command and sets the variables to their default values. The Cisco IOS softwarecommand reference

publications describe the effect of the defaultform of a command if the command functions differently

than the noform.

Saving Configuration ChangesUse the copy system:running-config nvram:startup-config command to save your configuration

changes to the startup configuration so that the changes will not be lost if the software reloads or a power

outage occurs. For example:

Router# copy system:running-config nvram:startup-configBuilding configuration...

It might take a minute or two to save the configuration. After the configuration has been saved, the

following output appears:

[OK]

Router#

On most platforms, this task saves the configuration to NVRAM. On the Class A Flash file system

platforms, this task saves the configuration to the location specified by the CONFIG_FILE environment

variable. The CONFIG_FILE variable defaults to NVRAM.

Filtering Output from the show and more CommandsYou can search and filter the output of showand morecommands. This functionality is useful if you

need to sort through large amounts of output or if you want to exclude output that you need not see.

To use this functionality, enter a showor morecommand followed by the pipe character (|); one of the

keywords begin, include, or exclude; and a regular expression on which you want to search or filter (the

expression is case-sensitive):

command| {begin| include| exclude} regular-expression

The output matches certain lines of information in the configuration file. The following example

illustrates how to use output modifiers with the show interfacecommand when you want the output to

include only lines in which the expression protocol appears:

Router# show interface | include protocol

FastEthernet0/0 is up, line protocol is upSerial4/0 is up, line protocol is upSerial4/1 is up, line protocol is upSerial4/2 is administratively down, line protocol is downSerial4/3 is administratively down, line protocol is down

For more information on the search and filter functionality, refer to the Using the Command-Line

Interface chapter in the Cisco IOS Configuration Fundamentals and Network Management

Configuration Guide.


36/443


37/443

C H A P T E R

2-1


Release 12.0(33)S, OL-8832-01, Rev. C9

2SIP and SPA Product OverviewThis chapter provides an introduction to modular services cards (SIPs) and shared port adapters (SPAs).

It includes the following sections:

Introduction to SIPs and SPAs, page 2-1

SPA Optics Compatibility, page 2-3

SIP and SPA Compatibility, page 2-5

For more hardware details for the specific SIP and SPAs that are supported on the Cisco 12000 series

router, refer to the companion publication, Cisco 12000 Series Router SIP and SPA Hardware

Installation Guide .

Introduction to SIPs and SPAsSIPs and SPAs are a new carrier card and port adapter architecture to increase modularity, flexibility, and

density across Cisco Systems routers for network connectivity. This section describes the SIPs and SPAs

and provides some guidelines for their use.

SPA Interface Processors

The following list describes some of the general characteristics of a SIP:

A SIP is a carrier card that inserts into a router slot like a line card. It provides no network

connectivity on its own.

A SIP can contain two or more subslots, which are used to house one or more SPAs. The SPA

provides interface ports for network connectivity.

During normal operation the SIP should reside in the router fully populated either with functional

SPAs in all subslots, or with a blank filler panel inserted in any empty subslots.

SIPs support online insertion and removal (OIR) while SPAs are inserted in their subslots.


38/443

2-2


Release 12.0(33)S, OL-8832-01, Rev. C9

Chapter 2 SIP and SPA Product Overview

Introduction to SIPs and SPAs

Shared Port Adapters

The following list describes some of the general characteristics of a SPA:

A SPA is a modular type of port adapter that inserts into a subslot of a compatible SIP carrier card

to provide network connectivity and increased interface port density. A SIP can hold one or more

SPAs, depending on the SIP type.

SPAs are available in the following sizes, as shown in Figure 2-1and Figure 2-2:

Single-height SPAInserts into a single SIP subslot.

Double-height SPAInserts into two single, vertically aligned SIP subslots.

Figure 2-1 Single-height and Double-height SPA Sizes

Figure 2-2 Horizontal and Vertical Chassis Slot Orientation for SPAs

Each SPA provides a certain number of connectors, or ports, that are the interfaces to one or more

networks. These interfaces can be individually configured within the Cisco IOS command-lineinterface (CLI).

Either a blank filler panel or a functional SPA should reside in every subslot of an SIP during normal

operation.

SPAs support online insertion and removal (OIR). They can be inserted or removed independently

from the SIP. OIR of a SIP with installed SPAs is also supported.

Single-height SPADouble-height SPA

Front of SIP

116886

SPA 0 SPA 1

SPA 2 SPA 3

Front of SIP, horizontal chassis slots

SPA0

SPA1

SPA2

SPA3

Vertical slot orientation

SPA 0 SPA 1

Double-height SPA SPA 3

SPA 1

Double-height SPA

116887

SPA 0

SPA 2


39/443

2-3


Release 12.0(33)S, OL-8832-01, Rev. C9



SFP and XFP Optics Modules

For more detailed information about the SFP and XFP optics modules, please refer to the applicable SPA

section in the Cisco 12000 Series Router SIP and SPA Hardware Installation Guide.

Table 2-1shows the SFP modules and their descriptions.

SPA Optics Compatibility

Table 2-2shows the types of optics modules that have been qualified for use with a SPA:

Table 2-1 SFP Modules

SPASFP Module

Product Number SFP Module Description

5-Port Gigabit Ethernet SPA SFP-GE-S Short wavelength

(1000BASE-SX)

Contains a Class 1 laser of 850 nm for

1000BASE-SX (short wavelength)

applications.

5-Port Gigabit Ethernet SPA SFP-GE-L Long wavelength/long haul

(1000BASE-LX/LH)


1000BASE-LX/LH (long wavelength)

applications.

5-Port Gigabit Ethernet SPA SFP-GE-Z Extended distance(1000BASE-ZX)

Contains a Class 1 laser of 1550 nm for1000BASE-ZX (extended wavelength)

applications.

1-Port 10-Gigabit Ethernet SPA XFP-10GLR XFP-10GLR-OC192SR Contains a Class 1 laser of 1310 nm for


applications.

1-Port 10-Gigabit Ethernet SPA XFP-10GER XFP-10GER-OC192IR Contains a Class 1 laser of 1550 nm for

1000BASE-ZX (extended wavelength)

applications.

5-Port Gigabit Ethernet SPA SFP-GE-S Short wavelength

(1000BASE-SX)


1000BASE-SX (short wavelength)

applications.

5-Port Gigabit Ethernet SPA SFP-GE-L Long wavelength/long haul

(1000BASE-LX/LH)



applications.

5-Port Gigabit Ethernet SPA SFP-GE-Z Extended distance

(1000BASE-ZX)


1000BASE-ZX (extended wavelength)

applications.

Table 2-2 SPA Optics Compatibility

SPA Qualified Optics Modules

2-Port T3/E3 Serial SPA None.

4-Port Clear Channel T3/E3 SPA None.

2-Port Channelized T3 SPA None.

4-Port Channelized T3 SPA None.


40/443

2-4


Release 12.0(33)S, OL-8832-01, Rev. C9



1-Port 10-Gigabit Ethernet SPA XFP-10GLR-OC192SR

XFP-10GER-OC192IR

1-Port 10-Gigabit Ethernet DWDM SPA XFP-10GLR-OC192SR

XFP-10GER-OC192IR

2-Port Gigabit Ethernet SPA SFP-GE-S

SFP-GE-L

SFP-GE-Z


SFP-GE-L

SFP-GE-Z


SFP-GE-L

SFP-GE-Z


SFP-GE-L

SFP-GE-Z

1-Port OC-192c/STM-64 POS/RPR SPA None.

1-Port OC-48c/STM-16 POS SPA SFP-OC48-SR OC48/STM16c SFP, Short Reach

SFP-OC48-IR1 OC48/ STM16c SFP, Intermediate

Reach

SFP-OC48-LR2 OC48/STM16c SFP, Long Reach(80km)

2-Port OC-48c/STM-16 POS SPA SFP-OC48-SR OC48/STM16c SFP, Short Reach

SFP-OC48-IR1 OC48/ STM16c SFP, Intermediate

Reach

SFP-OC48-LR2 OC48/STM16c SFP, Long Reach

(80km)

Table 2-2 SPA Optics Compatibility (continued)

SPA Qualified Optics Modules


41/443


42/443

2-6


Release 12.0(33)S, OL-8832-01, Rev. C9


SIP and SPA Compatibility

2-Port OC-48c/STM-16 POS SPA X X X

4-Port OC-48c/STM-16 POS SPA X X X

2-Port OC-3c/STM-1 and

OC-12c/STM-4 POS SPA, 4-Port

OC-3c/STM-1 and OC-12c/STM-4 POS

SPA, 8-Port OC-3c/STM-1 POS SPA

X X X

8-Port OC-12c/STM-4 POS SPA X X

Table 2-3 SIP and SPA Compatibility on the Cisco 12000 Series Router (continued)

SIP Type SIP Type

SPA2.5G ISESIP 400

10GSIP 600

2.5GSIP 401

5GSIP 501

10GSIP 601


43/443

C H A P T E R

3-1


Release 12.0(33)S, OL-8832-01, Rev. C9

3Overview of the Cisco 12000 Series Router SIPsThis chapter provides an overview of the release history, and feature and Management Information Base

(MIB) support for the SIPs supported on the Cisco 12000 Series Routers.

This chapter includes the following sections:

Release History, page 3-1

Supported Features, page 3-2

Supported MIBs, page 3-6

Displaying the SPA Hardware Type, page 3-9

Release History

Release Modification

Cisco IOS Release

12.0(31)S

Support for the following SPA interface processor (SIP) hardware was

introduced on the Cisco 12000 series routers:

Cisco 12000 SIP-400

Cisco 12000 SIP-600


44/443

3-2


Release 12.0(33)S, OL-8832-01, Rev. C9

Chapter 3 Overview of the Cisco 12000 Series Router SIPs

Supported Features

Supported FeaturesThis section provides a list of some of the primary features supported by the SIP hardware and software.

Cisco 12000 SIP-401, Cisco 12000 SIP-501, Cisco 12000 SIP-600, and Cisco 12000SIP-601 Features

The Cisco 12000 SIP-401, Cisco 12000 SIP-501, Cisco 12000 SIP-600, and Cisco 12000 SIP-601

provide a common 10 Gbps forwarding and queuing engine responsible for packet classification,

forwarding, queuing, and accounting without compromising performance. The Cisco 12000 SIP-401,

Cisco 12000 SIP-501, Cisco 12000 SIP-600, and Cisco 12000 SIP-601 have two forwarding engines,

one for ingress and one for egress. This allows the user to implement different features and QoS policiesfor the ingress and egress interfaces. The multicast replication is done by the egress forwarding engine,

hence a very scalable multicast with built-in QoS.

The Modular Physical Layer Interface Module (PLIM) front end hosts up to 2 SPAs. Each SPA has a

dedicated 10 Gbps interface to the SPA controller. The SPA controller uses a fair bandwidth allocation

algorithm to share available and excess bandwidth between the 2 SPAs. The oversubscribed SPA does

not cause any packet-drop on the nonoversubscribed SPA, and any unused bandwidth from one SPA is

used by the other SPA.


support any combination of the following pluggable SPAs and Layer 2 encapsulations:

Cisco IOS Release

12.0(32)S

Support for the following SPA interface processor (SIP) hardware was

introduced on the Cisco 12000 series routers:

Cisco 12000 SIP-401

Cisco 12000 SIP-501

Cisco 12000 SIP-601

Cisco IOS Release

12.0(33)S

Support for the following hardware by the Cisco 12000 SIP-600 and the

Cisco 12000 SIP-601 was introduced on the Cisco 12000 series router:

1-Port 10-Gigabit Ethernet SPA [WAN-PHY] (SPA-1X10GE-WL-V2)

1-Port 10-Gigabit Ethernet DWDM SPA (SPA-1X10GE-L-ITUC)

Support for the following hardware by the Cisco 12000 SIP-601 wasintroduced on the Cisco 12000 series router:

8-Port Gigabit Ethernet SPA (SPA-8X1GE-V2)

Support for the following hardware by the Cisco 12000 SIP-501 and

Cisco 12000 SIP-601 was introduced on the Cisco 12000 series router:


Information specific to BERT configuration for the following SPAs was

introduced:

2-Port and 4-Port Channelized T3 SPA

8-Port Channelized T1/E1 SPA

1-Port Channelized OC-3/STM-1 SPA


45/443

3-3


Release 12.0(33)S, OL-8832-01, Rev. C9


Supported Features

Concatenated OC-192 and OC-48

Gigabit Ethernet and 10 Gigabit Ethernet Interfaces

Point to Point Protocol (PPP)

High Level Data Link Control (HDLC)

Frame Relay

Dynamic Packet Transport (DPT)

Resilient Packet Ring (RPR)

802.17

VLANs

The SPA controller adapts the user traffic flowing between the SPA interfaces for the Layer 3 forwarding

engine. The SPA controller has two levels of priority queuing with Deficit Round Robin (DRR) and

Strict Priority Servicing. Strict Priority Servicing protects higher-priority packets by dropping lower

priority packets first, in an oversubscribed configuration (persistent incoming traffic rate of 20 Gbps.)


provide the following key features:

Dynamic allocation of 4096 input-shaped queues to any interface, subinterface, Frame Relay

connection, VLAN.

Ingress Queuing:

2048 unicast Modified DRR (MDRR) queues

16 high priority queues

8 multicast queues

2 fabric priority queues

Egress Queuing:

8192 Modified DRR (MDRR) queues dynamically shared across 4096 interfaces;

Hierarchical shaping (interface, queue)

High number of IPv4, IPv6, Multiprotocol Label Switching (MPLS), and MPLS VKPN unicast and

multicast routes: Up to 1M IPv4/MPLS routes and up to 512,000 IPv6 prefixes.

Per-VLAN/source-destination MAC address filtering, trunking, accounting, QoS, match VLAN

QoS, Hot Standby Router Protocol (HSRP)/Virtual Router Redundancy Protocol (VRRP)

hierarchical rate limiting and policing, dynamic queuing, and traffic shaping.

Input and output full NetFlow Version 8 in hardware.

Input and output Sampled NetFlow, Versions 5, 8, and 9 in hardware.

Building Integrated Timing Supply (BITS)

Online Insertion Removal (OIR) of SPAs; OIR of one SPA does not effect the traffic on other SPA

interfaces.

Multi-router Automatic Protection Switching (MR-APS)

Layer 2 VPNs over MPLS (Any transport over MPLS (AToM)) and Over IP Layer 2 Tunneling

Protocol Version 3 (L2TPv3)

The Cisco 12000 SIP-401, Cisco 12000 SIP-501, and Cisco 12000 SIP-601 provide the following key

features not available on the Cisco 12000 SIP-400 and Cisco 12000 SIP-600:

Finer control over power supply voltages


46/443

3-4


Release 12.0(33)S, OL-8832-01, Rev. C9


Supported Features

The 12.0(32)S release allows you to specify the percentage of voltage increase. If you dont specify

a percentage, the value used is the default percentage, which is 5%.

The output is enhanced to show nominal supply voltage, percentage margin, and actual read-back

voltage, to validate that the expected values were written and actually applied successfully.

Note High speed SPAs are only supported in bay 0 and 1 in routers with the Cisco 12000 SIP-401,

Cisco 12000 SIP-501, or Cisco 12000 SIP-601 SIP installed.

Cisco 12000 SIP-400 Features

The Cisco 12000 SIP-400 is a 2.5 Gbps IP Services Engine (ISE) SIP that hosts SPAs used for

applications that require a high level of performance, scalable physical and logical connections, and

high-touch QoS and security features. The Cisco12000 SIP-400 enhances and scales functionality with

benefits previously available on the 2.5 G ISE line card, allowing carriers to offer services such as VoIP,

MPLS VPN, Internet Access, and Low-speed Leased Line Aggregation (DS3, E3, CT3, n x T1, and n x

DS0).

The Cisco 12000 SIP-400 provides a common 10 Gbps forwarding and queuing engine that handles

packet classification, forwarding, queuing, and accounting without compromising performance. The

forwarding engine, based on the 12000 Series ISE technology, features a unique edge-optimized,

programmable adaptive network processor that combines the hardware performance of

Application-Specific Integrated Circuits (ASICs) with the flexibility of software.

The Modular Physical Layer Interface Module (PLIM) front end hosts up to 4 SPAs. Each SPA has a

dedicated 2.5 Gbps interface to the SPA controller. The Cisco 12000 SIP-400 supports any combination

of the following pluggable SPAs and Layer 2 encapsulation:

T3

E3

CT3

PPP/HDLC/FR

MLPPP

MLFR

The SPA controller adapts the traffic flowing between the SPA interfaces for the Layer 3 forwarding

engine. The SPA controller has two levels of priority queuing with Deficit Round Robin (DRR) and

Strict Priority Servicing. Strict Priority Servicing protects high priority traffic.

Key Features

The Cisco 12000 SIP-400 provides the following key features and benefits:

QoS

Provider Edge

Security

Accounting

High Availability


47/443

3-5


Release 12.0(33)S, OL-8832-01, Rev. C9


Supported Features

QoS

Traffic Shaping

Traffic Shaping offers additional value to service providers that want to build tiered service models. With

traffic shaping, the Cisco 12000 SIP-400 can absorb bursts of traffic in both the ingress and egressdirections. The Cisco 12000 SIP-400 supports up to 2048 input shaped queues and up to 1024 output

shaped queues dynamically allocated to any interface or subinterface. Traffic can be shaped down to

64 kbps.

Traffic Rate Limiting and Marking

Traffic Rate Limiting and Marking, using Committed Access Rate (CAR) or Modular QoS CLI (MQC),

allows service providers to control access to internal network resources. These features can be used to

protect against Denial of Service (DoS) attacks or to deliver tiered services.

Traffic Prioritization through MDRR with Low Latency Queuing (LLQ)

Traffic Prioritization through MDRR with Low Latency Queuing (LLQ) offers class-based packet

queuing that controls the packet dequeuing process to assure transit latency for differentiated flows. The

Cisco 12000 SIP-400 supports the following queues:

2048 unicast MDRR queues

16 high priority queues

1 multicast queue in the ingress direction

4096 MDRR queues dynamically shared across 1024 interfaces in the egress direction

Congestion Control through WRED and Query Management

Congestion Control through WRED and Query Management allows selective discard of low-priorityflows before dropping packets from higher-priority flows.

Provider Edge

The Cisco 12000 SIP-400 provides the following comprehensive MPLS capabilities that support the

development of service-optimized networks and can accelerate migration from circuit-based networks

to packet-based networks:

Layer 2 VPNs over MPLS (any transport over MPLS) and over IP (L2TPv3)

Layer 3 VPNs over MPLS and over IP, Multicast VPNs

Multilink Point-to-point Protocol (MLPPP)

Multilink Frame Relay (MLFR)

Link Fragmentation And Interleaving (LFI) over Frame Relay

IPv6 Unicast/Multicast

6PE


48/443


49/443

3-7


Release 12.0(33)S, OL-8832-01, Rev. C9


Supported MIBs

Cisco AAL5 MIB

Cisco APS MIB

Cisco ATM Extensions MIB

Cisco BGP Policy Accounting MIB

Cisco Bulk File MIB

Cisco CAR MIB

Cisco CDP MIB

Cisco Class-Based QoS MIB) aka MQC MIB)

Cisco Config Copy MIB

Cisco Config Man MIB

Cisco Enhanced MemPool MIB

Cisco EnvMon MIB

Cisco Flash MIB

Cisco Frame Relay MIB

Cisco FRU MIB

Cisco FTP Client MIB

Cisco HSRP Extensions MIB

Cisco HSRP MIB

Cisco IETF ATM2 PVCTRAP MIB

Cisco Image MIB

Cisco IP Statistics MIB

Cisco IP Mroute MIB Cisco MDRR MIB

Cisco Memory Pool MIN

Cisco Optical Monitoring MIB

Cisco PIM MIB

Cisco Ping MIB

Cisco Process MIB

Cisco Queue MIB

Cisco RTT Monitor MIB (SAA)

Cisco SRP MIB

Cisco Syslog MIB

Cisco TCP MIB

Cisco VLAN IFTABLE Relationship MIB

Cisco WRED MIB

DPT MIB

DS1/E1 MIB

DS3/E3 MIB


50/443

3-8


Release 12.0(33)S, OL-8832-01, Rev. C9


Supported MIBs

Entity MIB

Entity II MIB

Ethernet MIB

Ethernet RMON MIB

Ether-like MIB

Event MIB

Expression MIB

Fabric MIB

Frame Relay MIB (IETF)

Frame Relay DTE MIB

HSRP MIB

IF MIB

IF MIB for VLANs

IGMP MIB

Interfaces MIB

Int-Serv MIB

Int-Serv Guaranteed MIB

IP Mroute MIB

MPLS MIB

MPLS LDP MIB

MPLS LSR MIB

MPLS-TE MIB MPLS-TE Topo MIB

MPLS-VPN MIB

MPLS-DE-TE MIB

MQC MIB

MSDP MIB

Old Cisco Chassis MIB

Old Cisco CPU MIB

Old Cisco Interfaces MIB

Old Cisco IP MIB

Old Cisco Memory MIB

Old Cisco System MIB

Old Cisco TCP MIB

Old Cisco TS MIB

OSPFv2 MIB

PIM MIB

PSA Microcode MIB


51/443

3-9


Release 12.0(33)S, OL-8832-01, Rev. C9


Displaying the SPA Hardware Type

RFC1213 MIB

RFC1253 MIB

RFC1315 MIB

RFC1406 MIB

RFC1407 MIB

RFC1398 MIB

RFC1595 MIB

RMON MIB

RS232C MIB

RSVP MIB

SNMP Framework MIB

SNMP Target MIB

SNMP USM MIB

SNMP VACM MIB

SNMPv2 MIB

SNMP v3 MIB

SONET/SDH MIB

SONET Traps

Syslog Trap Alert on DLCI loss

TCP MIB

UDP MIB

WRED MIBTo locate and download MIBs for selected platforms, Cisco IOS releases, and feature sets, use Cisco

MIB Locator found at the following URL:

http://www.cisco.com/go/mibs

If Cisco MIB Locator does not support the MIB information that you need, you can also obtain a list of

supported MIBs and download MIBs from the Cisco MIBs page at the following URL:

http://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtml

To access Cisco MIB Locator, you must have an account on Cisco.com. If you have forgotten or lost your

account information, send a blank e-mail to [email protected]. An automatic check will verify

that your e-mail address is registered with Cisco.com. If the check is successful, account details with a

new random password will be e-mailed to you. Qualified users can establish an account on Cisco.com

by following the directions found at this URL:

http://www.cisco.com/register

Displaying the SPA Hardware TypeTo verify the SPA hardware type that is installed in your Cisco 12000 Series Router, you can use the

show gsrcommand.
http://www.cisco.com/go/mibshttp://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtmlhttp://www.cisco.com/registerhttp://www.cisco.com/registerhttp://www.cisco.com/public/sw-center/netmgmt/cmtk/mibs.shtmlhttp://www.cisco.com/go/mibs


52/443

3-10


Release 12.0(33)S, OL-8832-01, Rev. C9



Table 3-1shows the hardware description that appears in the showcommand output for each type of SPA

that is supported on the Cisco 12000 Series Router.

Example of the show gsr Command

The following example shows output from the show gsrcommand on a Cisco 12000 Series Router with

a Cisco 12000 SIP-400 installed in slot 1 and a Cisco 12000 SIP-600 installed in slot 3:

Router# show gsrhdm-193#show gsrSlot 0 type = ISE 2.5G SPA Interface Card state = IOS RUN Line Card Enabled subslot 0/0: SPA-4XT3/E3 (0x40B), status is ok subslot 0/1: SPA-4XT3/E3 (0x40B), status is ok

Table 3-1 SPA Hardware Descriptions in show Commands

SPA Description in show gsr Command2-Port T3/E3 Serial SPA SPA-2XT3/E3

4-Port T3/E3 Serial SPA SPA-4XT3/E3

1-Port Channelized OC-3/STM-1 SPA SPA-1XCOC3

8-Port Channelized T1/E1 SPA SPA-8XCT1/E1

2-Port Clear Channel T3/E3 SPA SPA-2XT3/E3

2-Port and 4-Port Clear Channel T3/E3 SPA SPA-4XT3/E3

2-Port Channelized T3 SPA SPA-2XCT3/DS0

4-Port Channelized T3 to DS0 SPA SPA-4XCT3/DS0

8-Port FastEthernet SPA SPA-8XFE, SPA-8x1FE-TX-V22-Port Gigabit Ethernet SPA SPA-2XGE, SPA-2X1GE-V2

5-Port Gigabit Ethernet SPA SPA-5XGE, SPA-5x1GE-V2

8-Port Gigabit Ethernet SPA SPA-8X1GE-V2

1-Port 10-Gigabit Ethernet SPA SPA-1XTENGE-XFP, SPA-1X10GE-L-V2,

SPA-1X10GE-WL-V2

1-Port 10-Gigabit Ethernet DWDM SPA SPA-1X10GE-L-ITUC

10-Port Gigabit Ethernet SPA SPA-10XGE-XFP, SPA-10X1GE-V2

1-Port OC-192c/STM-64 POS SPA SPA-OC192POS

2-Port OC48-POS/RPR SPA SPA-2XOC48POS

2-Port and 4-Port OC-48c/STM-16 POS SPA SPA-4XOC48-POS/RPR

2-Port OC-3c/STM-1 and OC-12c/STM-4 POS

SPA

SPA-2XOC12-POS


SPA

SPA-4XOC12-POS


SPA

SPA-8XOC12-POS

4-Port OC-3c/STM-1 POS SPA SPA-4XOC3-POS

8-Port OC-3c/STM-1 POS SPA SPA-8XOC3-POS


53/443

3-11


Release 12.0(33)S, OL-8832-01, Rev. C9



subslot 0/2: SPA-4XT3/E3 (0x40B), status is ok subslot 0/3: SPA-2XCT3/DS0 (0x43C), status is okSlot 1 type = ISE 2.5G SPA Interface Card state = IOS RUN Line Card Enabled subslot 1/0: SPA-4XT3/E3 (0x40B), status is ok subslot 1/1: SPA-2XT3/E3 (0x40C), status is ok

subslot 1/2: SPA-4XT3/E3 (0x40B), status is ok subslot 1/3: SPA-2XT3/E3 (0x40C), status is okSlot 2 type = ISE 2.5G SPA Interface Card state = IOS RUN Line Card Enabled subslot 2/0: SPA-4XT3/E3 (0x40B), status is ok subslot 2/1: SPA-4XT3/E3 (0x40B), status is ok subslot 2/2: SPA-2XT3/E3 (0x40C), status is ok subslot 2/3: SPA-4XT3/E3 (0x40B), status is okSlot 3 type = ISE 2.5G SPA Interface Card state = IOS RUN Line Card Enabled subslot 3/0: SPA-4XT3/E3 (0x40B), status is out of service subslot 3/1: SPA-4XT3/E3 (0x40B), status is ok subslot 3/2: Empty subslot 3/3: EmptySlot 4 type = ISE 2.5G SPA Interface Card

state = IOS RUN Line Card Enabled subslot 4/0: Empty subslot 4/1: Empty subslot 4/2: Empty subslot 4/3: EmptySlot 9 type = Performance Route Processor state = ACTV RP IOS Running ACTIVESlot 16 type = Clock Scheduler Card(10) OC-192 state = Card PoweredSlot 17 type = Clock Scheduler Card(10) OC-192 state = Card Powered PRIMARY CLOCKSlot 18 type = Switch Fabric Card(10) OC-192 state = Card PoweredSlot 19 type = Switch Fabric Card(10) OC-192 state = Card Powered

Slot 20 type = Switch Fabric Card(10) OC-192 state = Card PoweredSlot 21 type = Switch Fabric Card(10) OC-192 state = Card PoweredSlot 22 type = Switch Fabric Card(10) OC-192 state = Card PoweredSlot 24 type = Alarm Module(10) state = Card PoweredSlot 25 type = Alarm Module(10) state = Card PoweredSlot 29 type = Blower Module(16) state = Card Powered


54/443

3-12


Release 12.0(33)S, OL-8832-01, Rev. C9




55/443

P A R T 2

Gigabit Ethernet Shared Port Adapters


56/443


57/443

C H A P T E R

4-1

Cisco 12000 Series Router SIP and S

Cisco 12K Config Guide

Documents

Transcript of Cisco 12K Config Guide

Avaya - Cisco Interoperability Technical Config Guide

cisco to sonicwall config vpn

Cisco SF300 Config

Vpn config-on-cisco-devices

Howto Aw- Config Pvst Interop Cisco REVB

Cisco Asa 5500 Series Config From Cisco

Cisco CCNA CBT -Basic Catalyst Switch Config

Cisco IOS & Router Config

Cisco - Config LACP and Load Balancing

Cisco Config Ass

Config Switch Cisco 4500

Cisco Nexus 7000series Fundamental Config Guide

Cisco Wide Area Application Services Command Reference · (config) aaa accounting 212 (config) alarm overload-detect 216 (config) asset 218 (config) authentication 219 (config) auto-register

Cisco SPA122 ATA Config FreePhoneLine

Configurar Router con Cisco Config Maker

Cisco Security Appliance Config Guide_v7-1

Cisco 860-890 ISR Config Guide

Cisco VLAN Config

Cisco 7600 Config Guide

ConfiguringSecurity - Cisco€¦ · apic1(config-host)# timeout 3 apic1(config-host)# descr "My primary RADIUS server" apic1(config-host)# key myRaDiUSpassWoRd apic1(config-host)#