chippersCHIPPER RANGE

ENG

HEINOLA 55 RRobustly constructed chipper with slope infeed for chipping smaller quantities of wood material. Especially suitable for chipping the joinery industry’s by-products, sawmill strips and rejects.

Drum diameter ................................................... 500 mmInfeed opening, width ....................................... 500 mmInfeed opening, height ...................................... 250 mmNumber of knives ................................................... 4 pcsRequired power .............................................. 22–55 kWCapacity ..........................................................5–25 m3/hWeight ...................................................approx. 1100 kg

HEINOLA 97 REChipper with slope infeed for chipping sawmill dry and green cut-offs.

Drum diameter ................................................... 900 mmInfeed opening, width ....................................... 680 mmInfeed opening, height ............................... 440/580 mmNumber of knives ................................................4/6 pcsRequired power ............................................ 75–160 kWCapacity ......................................................40–110 m3/hWeight ..................................................approx. 4500 kg

THE HEINOLA chipper product family includes chippers for sawmills, the veneer and plywood industry, the pulp and paper industry as well as for bioenergy production. The HEINOLA chippers are well known for their low operating costs, long life, effi ciency and excellent chip quality.

HEINOLAindustrial chippers

CHIPPERS with slope infeed

Evenchip quality

Highcapacity

Spare partsreadily

available

Low energyconsumption

HEINOLA 137 REChipper with slope infeed for chipping dry and green cut-offs. An excellent choice for chipping the pulp and papers industry’s irregularly-sized pieces and the veneer and plywood industry’s trim ends.

Drum diameter ................................................ 1 300 mmInfeed opening, width ....................................... 770 mmInfeed opening, height ...................................... 750 mmNumber of knives ................................................4/6 pcsRequired power .......................................... 160–500 kWCapacity ....................................................100–300 m3/hWeight ..................................................approx. 6500 kg

CHIPPERS with feeding devices

HEINOLA 75 RSEChipper with horizontal infeed for chipping sawmill slabs, edgings and trim ends.

Drum diameter ................................................... 700 mmInfeed opening, width ....................................... 570 mmInfeed opening, height ...................................... 265 mmNumber of knives ................................................... 4 pcsRequired power ............................................ 45–110 kWCapacity ........................................................20–80 m3/hInfeed device with pneumaticallyrelieved infeed roll with drive aboveWeight ..................................................approx. 3500 kg

CHIPPERS with slope infeed

”FOR US working here at Heinola, the HEINOLA brand represents the combination of decades of expertise, experience and responsibility. Our operations are based on listening to our customers and developing new innovations.”

MATTI TAKATALOSales Director

HEINOLA 97 RSEChipper with horizontal infeed for chipping sawmill slabs, edgings and trim ends.

Drum diameter ................................................... 900 mmInfeed opening, width ....................................... 660 mmInfeed opening, height ...................................... 330 mmNumber of knives ................................................4/6 pcsRequired power ............................................ 75–160 kWCapacity ......................................................40–110 m3/hInfeed device with pneumaticallyrelieved infeed roll with drive aboveWeight ..................................................approx. 5200 kg

HEINOLA 97 RSVEChipper with horizontal infeed for chipping sawmill slabs, edgings and trim ends, especially suitable for chipping material with lots of short trim ends.

Drum diameter ................................................... 900 mmInfeed opening, width ....................................... 660 mmInfeed opening, height ...................................... 330 mmNumber of knives ................................................4/6 pcsRequired power ............................................ 75–160 kWCapacity .....................................................40–110 m3/hFeeding device with rolls; 5 rolls with drive and pneumatically relieved roller unit’s upper partWeight ...................................................approx. 5500 kg

HEINOLA 137 RSEChipper with horizontal infeed for chipping large amounts of sawmill slabs, edgings and cut-offs.

Drum diameter ................................................. 1300 mmInfeed opening, width ....................................... 700 mmInfeed opening, height ...................................... 435 mmNumber of knives ................................................4/6 pcsRequired power ......................................... 160–500 kWCapacity ....................................................100–300 m3/hInfeed device with a pneumaticallyrelieved infeed roller above and 3 infeed rolls with drive belowWeight ...............................................approx. 10,000 kg

HEINOLA 1310 RSEChipper with horizontal infeed for chipping tree trunks and logs for the energy industry, e.g. for chipping stations. Especially suitable for chipping pulpwood for the pulp industry and as a pre-processing machine for the pellet factories.

Drum diameter ................................................ 1 300 mmInfeed opening, width .................................... 1 000 mmInfeed opening, height ...................................... 730 mmNumber of knives ................................................... 2 pcsRequired power .......................................... 270–630 kWCapacity ....................................................150–350 m3/hInfeed device with 3 hydraulic rolls below and a hydraulic infeed roller with hydraulic relief aboveWeight ...............................................approx. 11,000 kg

HEINOLA 97 RSV4Veneer chipper with horizontal infeed for chipping veneer mill waste, veneer cores and plywood edgings.

Drum diameter ................................................... 900 mmInfeed opening, width ....................................... 700 mmInfeed opening, height ...................................... 250 mmNumber of knives ................................................... 4 pcsRequired power ............................................ 90–132 kWCapacity ........................................................50–80 m3/hInfeed device with 3 rolls with drivebelow and 2 rolls with drive andpneumatic relief aboveWeight .................................................approx. 5,500 kg

HEINOLA 910 RSVVeneer chipper with horizontal infeed for chipping veneer mill waste, veneer cores and plywood edgings.

Drum diameter ................................................... 900 mmInfeed opening, width ..................................... 1000 mmInfeed opening, height ...................................... 400 mmNumber of knives ................................................... 4 pcsRequired power .......................................... 100–315 kWCapacity ....................................................100–250 m3/hInfeed device with 3 rolls with drive below, 4 rolls with drive and pneumatic relief and 1 pre-pressing roll with drive aboveWeight ...............................................approx. 10,300 kg

HEINOLA Mobile Chippers are incomparable regarding chip quality, durability and capacity. The annual operating costs are low. The massive construction combined with easily changed main knives guarantee carefree operation in demanding conditions.

HEINOLAmobile chippers

TRUCK-MOUNTEDchippers

HEINOLA 910 TRUCKSuitable for producing woodchips for power generation, this mobile chipper is mounted on a truck and powered by the carrier vehicle’s engine via an easy-to-use power cable. Suitable for chipping whole trees, tree trunks and logging residues.

Drum diameter ................................................... 900 mmInfeed opening, width ..................................... 1000 mmInfeed opening, height ...................................... 720 mmMaximum trunk diameter ................................. 480 mmChipping knives ...................................................... 2 pcsPower ........................................................... 300–570 kWChip output ...............................................max 300 m3/hTotal weight .......................................approx. 26 000 kg• Fed by a hydraulically operated roller / lamella

conveyor and a hydraulically operated large-diameter top roller

• Chip ejection via chip pipe with a hydraulically operated chip ejector

• Three-axle carrier vehicle

HEINOLA 1014 TRUCKSuitable for producing woodchips for power generation, this wide mobile chipper model is mounted to a truck and powered by the carrier vehicle’s engine via an easy-to-use power cable. Thanks to its increased width, this chipper is ideal for chipping logging residues, and it can also process whole trees and tree trunks.

Drum diameter ................................................ 1 000 mmInfeed opening, width .................................... 1 400 mmInfeed opening, height ...................................... 720 mmMaximum trunk diameter ................................. 540 mmChipping knives ..................................................2+2 pcsPower ........................................................... 370–600 kWChip output ...............................................max 350 m3/hTotal weight .......................................approx. 30,000 kg• Fed by a hydraulically operated lamella conveyor

as well as a large-diameter top roller• Chip ejection via chip pipe with a hydraulically

operated chip ejector• 3- or 4-axle carrier vehicle

TRUCK-MOUNTEDchippers

HEINOLA 1310 TRUCKSuitable for producing woodchips for power generation, this mobile chipper is mounted on a truck and powered by the carrier vehicle’s engine via an easy-to-use power cable. Suitable for chipping whole trees, tree trunks and logging residues. Also an effi cient and economical chipper

for large trunks.

Drum diameter ..................................................1300 mmInfeed opening, width ......................................1000 mmInfeed opening, height .......................................750 mmMaximum trunk diameter ..................................700 mmChipping knives .......................................................2 pcsPower ............................................................370–600 kWChip output ...............................................max 400 m3/hTotal weight ....................................... approx. 31,000 kg• Fed by a hydraulically operated lamella

conveyor as well as a hydraulically operated large-diameter top roller

• Chip ejection via chip pipe with a hydraulically operated chip ejector

• 3- or 4-axle carrier vehicle

HEINOLA 1310 PACKSuitable for producing fuel chips, this mobile chipper and engine unit is mounted to a truck and powered by a separate 565-kW Volvo Penta engine. Suitable for chipping whole trees, tree trunks and logging residues. Also available with a mounting system

compatible with roll-off trucks.

Drum diameter ..................................................1300 mmInfeed opening, width ......................................1000 mmInfeed opening, height .......................................700 mmMaximum trunk diameter ..................................700 mm Chipping knives .......................................................2 pcsPower ....................................................................565 kWChip output ...............................................max 400 m3/hWeight ...approx. 18,000 kg (excluding carrier vehicle)• Fed by a hydraulically operated lamella

conveyor as well as a hydraulically operated large-diameter top roller

• Chip ejection via chip pipe with a hydraulically operated chip ejector

• 4-axle carrier vehicle

HEINOLA 1310 TRAILERSuitable for producing fuel chips, this mobile chipper is mounted to a semi-trailer and powered by a separate 565-kW Volvo Penta engine. Suitable for chipping whole trees, tree trunks and logging residues, and particularly for terminal use.

Drum diameter .................................................1300 mmInfeed opening, width ......................................1000 mmInfeed opening, height .......................................750 mmMaximum trunk diameter ..................................700 mm Chipping knives .......................................................2 pcsPower ....................................................................565 kWChip output ...............................................max 500 m3/hWeight ................................................ approx. 21,000 kg• Fed by a hydraulically operated lamella

conveyor as well as a hydraulically operated large-diameter top roller

• Chip ejection via a belt conveyor

CHIPPERS POWERED BYseparate engine

Chip ejection via chip pipe with a hydraulically operated chip ejector4-axle carrier vehicle

Näk

emys

tehd

as M

BE –

Mar

kprin

t O

y, 2

018

Heinola Sawmill Machinery Inc. • P.O. Box 24, 18101 Heinola, Finland • Tel. +358 (0)3 848 411 • www.heinolasm.fi

SAWLINES • EDGING • LUMBER HANDLING • DRYING KILNS • CHIPPERS • AUTOMATION • HEINOLA CARE

HEINOLA SAWMILL MACHINERY INC. has decades of expertise in sawmill process solutions. Our experience

and creative solutions ensure that sawmill customers receive skilled service,from single machines to complete plants. HEINOLA provides sawmills

with customer-led, reliable and cost-effective solutions. The deliveryprogramme includes all the main processing requirements, with the necessary

auxiliary equipment, delivered as a total turnkey solution if desired.