CHEVROLET EQUINOX / GMC TERRAINchevrolet equinox / gmc terrain 2/12/2020 13307 scan for more...
Transcript of CHEVROLET EQUINOX / GMC TERRAINchevrolet equinox / gmc terrain 2/12/2020 13307 scan for more...
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.
WARNING: ALL NON-TRAILER LOADS APPLIED TO THIS PRODUCT MUST BE SUPPORTED BY 18050 STABILIZING STRAPS.
WARNING: ** FAILURE TO PROPERLY SUPPORT NON-TRAILER LOADS WILL VOID PRODUCT WARRANTY **
WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY ***
FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COMHAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-877-287-8634
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERS
ARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.
CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.
3,500 525
34
20
CHEVROLET EQUINOX / GMC TERRAIN2/12/2020
13307
40
Scanfor moreinformation
Parts List
DESCRIPTIONPART NUMBERQTYITEM
NUT, SER-FLANGE,1/2-13 UNC,GRD8,YZ20-0006261
BOLT,CAR,1/2-13 UNC,1-3/4,GRD8,YZ10-1027262
.250 x 1.00 x 2.50" SQUARE HOLE SPACERCM-SP1063
1/2" FISHWIRE1_2 FISHWIRE64
1. On passenger frame rail locate and carefully remove plastic pushpin from bottom of rail using a pry tool.
NOTE: Enlarging the access hole with die grinder to 1.125" to allow the carriage bolts and spacers to be inserted into frame rail may ease installation. 2. Fishwire (2) CM-SP10 spacers and (2) 1/2" carriage bolts through access hole and out mounting holes on each side. (As shown in the Fishwire Technique Diagram)
3. Reverse fishwire (1) CM-SP10 spacer and (1) 1/2" carriage bolt through access hole and out access hole on each side. (As shown in the Reverse Fishwire Technique Diagram) 4. Raise hitch into position and secure with (3) 1/2" flange nuts on each side. 5. Torque 1/2" hardware to 110 ft-lbs. INSTALLATION COMPLETE
4
2
3
1
-FISHWIRE HARDWARE-REVERSE FISHWIRE HARDWARE
-NO DRILLING
TOOLS REQUIRED
RATCHET
TORQUE WRENCH
6" SOCKET EXT
3/4" SOCKET
PRY BAR
SAFETY GLASSES
DIE GRINDER
MAKE: STYLE:
MIN.20
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITYFor more information log onto www.curtmfg.com & for helpful towing tips log onto www.hitchinfo.com
WEIGHT CARRYING:
INSTALLATION TIPS:
INSTALLATION REQUIRES:
VEHICLE PHOTO:
HITCH ILLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HITCH MATCHES
LEVEL OF DIFFICULTY: EASY
MODERATE CHALLENGING
1. BEFORE YOU BEGIN INSTALLATION, READ ALL
INSTRUCTIONS THOROUGHLY.
2. TO EASE INSTALLATION, 2 PEOPLE MAY BE
REQUIRED.
3. USING PROPER TOOLS WILL GREATLY IMPROVE
THE QUALITY OF THE INSTALL AND REDUCE THE
TIME REQUIRED. 4. NEED HELP OR HAVE SOME QUESTIONS?
CALL TECHNICAL SUPPORT AT 800.798.0813
Safety glasses should be worn at all times whileinstalling this product .
YEARS: 2018-PRESENT CHEVROELT / GMC MODEL: EQUINOX / TERRAIN SUV
3,500
525
TRAILER WEIGHT:
TONGUE WEIGHT:
13307 INSTALLATION INSTRUCTIONS
LBS.
LBS.
MIN.40
IF YOU ARE HESITANT TO UNDERTAKE
THIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED
CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
NOVICE INSTALL TIME:
PRO INSTALL TIME:
SCAN FOR
MORE INFO
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUNDCURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,CURT Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this productvoids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.
For more information log onto www.curtmfg.comThis product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684. 2/12/2020
EASY
WARNING: WE RECOMMEND THE USE OF 18050 STABILIZING STRAPS FOR ALL NON-TRAILER (WHEEL-LESS) LOADS. PLEASE SEE THE CURT CATALOG OR VISIT US ONLINE AT WWW.CURTMFG.COM FOR FURTHER INFORMATION.
RATCHETTORQUE
WRENCH
SOCKET
3/4"
PRY BARSAFETY
GLASSES
NO DRILLING REQUIRED
FISHWIRE HARDWAREREQUIRED
REVERSE FISHWIREHARDWARE REQUIRED
SOCKETEXTENSION
6"
DIE GRINDER
HOLE ENLARGEMENT
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com
Parts List
DESCRIPTIONPART NUMBERQTYITEM
NUT, SER-FLANGE,1/2-13 UNC,GRD8,YZ20-0006261
BOLT,CAR,1/2-13 UNC,1-3/4,GRD8,YZ10-1027262
.250 x 1.00 x 2.50" SQUARE HOLE SPACERCM-SP1063
1/2" FISHWIRE1_2 FISHWIRE64
PASSENGER SIDEFRAME RAIL
DRIVER SIDEFRAME RAIL 4
2
1
3
1. On passenger frame rail locate and carefully remove plastic pushpin from bottom of rail using a pry tool. NOTE: Enlarging the access hole with die grinder to 1.125" to allow the carriage bolts and spacers to be inserted into frame rail may ease installation.
2. Fishwire (2) CM-SP10 spacers and (2) 1/2" carriage bolts through access hole and out mounting holes on each side. (As shown in the Fishwire Technique Diagram)
ACCESS HOLE
(BOTH SIDES)
MOUNTING HOLES
(BOTH SIDES)
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com
3. Reverse fishwire (1) CM-SP10 spacer and (1) 1/2" carriage bolt through access hole and out access hole on each side. (As shown in the Reverse Fishwire Technique Diagram)
4. Raise hitch into position and secure with (3) 1/2" flange nuts on each side.
5. Torque 1/2" hardware to 110 ft-lbs..
INSTALLATION COMPLETE