CHEMICAL TANKER MANUAL -...
Transcript of CHEMICAL TANKER MANUAL -...
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 1 of 46
3.1. GENERAL
When transferring cargo in port, vessel must strictly comply with company instructions, local rules and
regulations. Such operation will require:
1. Adequate and well trained crew.
2. Proper securing of the vessel to the terminal.
3. Operation in accordance with company checklists.
4. Specific fuel and ballast handling procedures.
5. Continuous inspections of cargo hoses, pipeline systems, tanks, equipment and the water around
the vessel.
6. Instructions for emergencies or potential hazardous situations.
7. The establishment of lines of authority and responsibility.
8. Ship board communication during cargo transfer shall be in English language.
9. All communication with the terminal and other external parties must be in English.
3.2. RESPONSIBILITIES
Knowledge of Cargo System
The Master and all Deck Officers must have an intimate knowledge of all cargo pumps, pipeline systems,
instrumentation and ancillary equipment on the vessel.
The following shall be suitably marked for easy identification:
1. Cargo lines and valves.
2. Tank-vents, vent-lines and IG lines.
3. Vapour-locks.
4. Cargo-heaters and heating-lines.
5. Cargo-pumps and pump room valves / lines.
6. Butterworth-pockets, manholes, and tank-domes.
7. Tank-cleaning lines.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 2 of 46
Following information should be readily displayed in CCR
1. Maximum permissible loading rates for each cargo tank and, where tanks have a combined venting
system, for each group of cargo tank.
2. Loading rate for Static accumulating cargoes - Poster .
3. Cargo pump capacity and pump manufacturer technical data including pump performance curve for
various speeds etc.
4. Flammability Composition diagram. Poster
5. Mimic diagram of cargo / tank cleaning / ballast / venting system / IG.
6. Cargo Compatibility Chart - Poster
7. Cargo hose resistance list.
8. PV valve pressure / vacuum settings and Cargo Tank Pressure Sensor Alarm Settings.Poster
9. Chief Officer’s Standing Orders.
10. Cargo Tank Inert Gas branch line Valve Status Board.
11. Placard for ‘Closed Sampling’ .
12. Precaution in case of failure of Fixed Gauging System while handling static accumulating cargoes.
13. Cargo line / Pumping diagram - Poster.
14. Vapour system piping diagram - Poster.
15. Ballast system pumping / piping diagram - Poster.
16. Any restrictions for ballasting / deballasting - Poster.
17. Cargo Pump operating procedure - Poster .
18. Plan with position of UTI ports, Overfill alarms and Radar gauges - Poster .
19. Damage stability – Shore based organization contact - Poster .
20. Pouch for Cargo MSDS / Dangerous cargo information - Poster .
21. Makers coating specification for cargo tanks - Poster .
22. Max loading / unloading / venting rates information chart - Poster .
23. Information chart for Max load density/restrictions in loading cargo tanks - Poster .
24. 98% & 95% ullage chart for cargo tanks at even keel - Poster.
25. Cargo pump pumping characteristic diagram (specially parallel) - Poster
26. Dangers of Nitrogen - Poster .
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 3 of 46
3.2.1. Chief Officers Instructions for Cargo Operations
The Chief Officer should write instructions of the procedures to be followed during periods when he is not
on duty. In addition, standing instructions should be posted in CCR for duty officer’s ready reference.
3.2.2. Pre Cargo Operation Safety Conference
A ‘Pre-Cargo Operation Safety Conference’ which includes a review of the ‘OP-CHEM-01’ should be
conducted onboard preferably 24 hours prior arrival port with all concerned crew members. Detailed
information regarding hazards and PPE required for cargoes being handled MUST be discussed including
but not limited to the following:
1. Cargo Name / Quantity / MSDS details / Pollution Category.
2. Gauging and Sampling Requirement.
3. Cargo Vapour Content Hazard.
4. Skin / Eye Contact Hazard.
5. Poison / Toxic Hazard / Antidote.(Antidotes to be available onboard for the nominated cargo with
sufficient quantities .This should be available prior loading the cargo and until the cargo has been
discharged the antidotes will sufficient quantity to be maintained onboard .Details can be obtained from
MFAG. Medical advice to be obtained prior administrating antidotes to the casualty)
6. Flash point / Extinguishing medium.
7. PPE Level required for safe handling of the cargo.
The above is to be documented using the relevant section in the " OPS –CHEM-01 Cargo transfer and
Tank cleaning plan”
A briefing is also to be carried out of other crew members to make them aware of the Hazards of the
cargo, the precautions to be taken and actions in case of an emergency. This should be documented in
the “Deck Log Book ”.
3.2.3. Personnel Protection
The use of proper personal protection is of paramount importance in the work place. This is especially
critical on chemical tankers. In order to choose the appropriate personal protection it is essential to
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 4 of 46
assess the risk levels. The level of risk must be evaluated basis the possibility of exposure to the product
depending on the nature of the task and the hazards of the cargo being handled. The main health
hazards of the chemical cargoes are due to inhalation, ingestion or skin contact. The personal protective
equipment must provide adequate level of protection in the event of exposure to the cargo. It has to be
understood that any form of exposure to the products must be avoided.
In making this assessment following considerations must be made:
1. Activities which are considered high risk.
2. Demarcation of Manifold and Work Areas.
3. PPE Level Requirements.
Maximum level of protection is required for High Risk Activities and / or High Risk Areas when handling
Highly Toxic / Highly Corrosive cargoes and use of Level 3 PPE would hence be necessary.
When handling chemicals which are less hazardous or working in areas which pose a lesser risk, lower
protection levels such as PPE Level 2 or PPE level 1 may be suitably adopted.
Filter Mask Use of Filter mask is strictly prohibited onboard the company vessel
3.2.3.1. Personal Protective Equipment (Ppe) on Chemical Tankers
Protective equipment broadly consist of the following:
1. Chemical Resistant Shoes:
Provide moderate to high level of protection against most chemicals. However they may not be suitable
for highly corrosive and toxic chemicals.
2. Chemical Resistant Gloves:
Provide moderate to high level of protection against most chemicals. However they may not be suitable
for highly corrosive and toxic chemicals.
3. Chemical Resistant Goggles:
Provide Eye protection and are worn to protect against chemical splash. However they may not be
suitable for highly corrosive and toxic chemicals.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 5 of 46
4. Chemical Resistant Suits:
Provide moderate to high level of protection against most chemicals. However they may not be suitable
for highly corrosive and toxic chemicals. Material of the suit should be compatible with the chemical being
handled. These suits must be worn along with suitable rubber gloves, chemical resistant boots, chemical
goggles and hard hat. These form part of Level 2 PPE
5. Gas tight full body chemical suits:
Integral with hood, boots and gloves. Must be worn in conjunction with SCBA. Material of these suits
should be compatible with the product. They provide the highest level of protection and are specifically
developed for protection against toxic, corrosive gases, and liquids. These form part of Level 3 PPE. The
gas tight suits must be pressure tested once every year.
6. Self Contained Breathing Apparatus (SCBA):
Chemical carriers are supplied with additional sets of SCBA sets as required by IBC. These additional
sets are usually known as IBC sets. They should be distinctly identified and maintained ready for
immediate use. These sets should be used as necessary by personnel involved in cargo operations
involving hazardous chemicals and for fire fighting. SCBA should be stored in a place where it is easily
accessible. Units should be located so as to be available for emergencies in different parts of the ship.
These sets should be serviced annually by a competent person ashore.
7. Emergency Escape Breathing Apparatus (EEBD):
Ships certified for the carriage of certain cargoes listed in IBC Code are required to be provided with
respiratory and eye protection sufficient for every person on board for emergency escape capable of air
supply for 15 minutes. This equipment is for emergency escape only and must not be used for any other
purposes.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 6 of 46
PPE LEVEL 1 Overalls, Safety Shoes, Chemical Resistant Gloves, Goggles, Helmet & Personal Gas Detector
PPE LEVEL 2
Chemical Protective Suit, Chemical Resistant Gloves/ Goggles/ Shoes, Helmet & Personal Gas Detector
1. Use 'Acid Hood' in lieu of goggles while handling corrosive cargoes.
2. Respiratory protection such as 'ELSA' shall be kept readily available while handling toxic cargoes.
PPE LEVEL 3
Chemical Protective Suit with respiratory equipment, Chemical Resistant Gloves/ Goggles/ Shoes. Helmet and Personal Gas Detector
Required to be worn by crew members involved in 'Critical Phases' of cargo operations while handling toxic cargoes.
3.2.3.2. High Exposure Risk Operations / Locations
These include but are not limited to:
1. Working at the Manifolds including connection / disconnection.
2. Gauging.
3. Sampling.
4. Tank Cleaning with Portable Machines.
5. Opening any part of the cargo containment system (tank hatches, drains, etc).
6. Purging cargo pump cofferdams / Blowing through heating coils.
7. Any other task / location where the risk of exposure has been deemed to exist.
8. Cleaning spillage on deck, or over side.
3.2.3.3. Demarcation of Cargo Manifold Area / Work Areas
The Cargo manifold of a Chemical tanker is deemed to be a high risk area during the transfer of Chemical
cargoes. This area should not be entered unless otherwise required. During the transfer operation of
Highly toxic / Highly corrosive cargoes the manifold area should be demarcated by permanent marking or
cordoned off using Barrier Tapes / Ropes to safeguard against the inadvertent entry of unauthorised
personnel or personnel wearing inadequate PPE.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 7 of 46
Minimum of two meters on around the manifold area should be demarcated
Similar precautions and controls must be applied to any other areas on the Cargo deck where risk of
exposure exists.
Adequate level of PPE must be complied with when entering these areas.
3.2.3.4. Preparation and Use of PPE
1. Vessel should have three complete sets of safety equipment as per IBC code Ch. 14.2.
2. At least one set of safety equipment shall be kept accessible in suitable clearly marked locker near
cargo pump room and one set at the manifold.
3. Minimum two Emergency decontamination showers and an eye wash, operable in all ambient
conditions, shall be available on deck.
4. Crew members must comply with the appropriate PPE level as identified in the "OP-CHEM-01
Cargo transfer and Tank cleaning plan."
5. When handling multiple parcels at the same time, the most severe applicable PPE Level must be used.
6. The crew member should remove chemical resistant PPE prior entering accommodation and these
should be decontaminated and washed with Fresh water after each use and dried properly prior stowing.
7. Records of decontamination must be maintained on board.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 8 of 46
3.2.3.5. PPE Level Requirements
Highly Corrosive and / or Highly Toxic Cargoes
Examples: Sulphuric Acid, Nitric Acid, Hydrochloric Acid, Phenol, Acrylonitrile, Toluene Di-
Isocyanite(TDI) Etc.
Level 1 Level 2 Level 3
Operation
Working at the Manifolds including line clearing, connection /
disconnection
X
Monitoring the manifold including operating valves / reading
manifold pressure.
X
Gauging / Sampling / Stripping X
Opening any part of the cargo containment system (tank hatches,
drains, etc.)
X
Tank Cleaning with Portable Machines X
Purging cargo pump cofferdams / Blowing through heating coils. X
Any other task/ location where the risk of exposure has been
deemed to exist.
X
Spill response X
Deck watch when Vapour Return is provided. X
Deck watch when Vapour Return is not provided. X
Mildly Corrosive and / or Toxic Cargoes
Examples : Styrene Monomer, Vinyl Acetate Monomer (VAM), Acetic Acid, Phosphoric Acid, Butyl
Acrylate
Working at the Manifolds including line clearing, connection /
disconnection
X
Monitoring the manifold including operating valves / reading X
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 9 of 46
manifold pressure.
Gauging / Sampling / Stripping X
Opening any part of the cargo containment system (tank hatches,
drains, etc.)
X
Tank Cleaning with Portable Machines X
Purging cargo pump cofferdams / Blowing through Heating coils X
Any other task/ location where the risk of exposure has been
deemed to exist.
X
Spill response X
Deck watch X
Non Corrosive and Non Toxic Cargoes
Examples : Soya bean Oil, Canola Oil, Lubricating Oil, Paraffin Wax, Motor Gasoline etc.
Working at the Manifolds including line clearing, connection /
disconnection
X
Monitoring the manifold including operating valves / reading
manifold pressure.
X
Opening any part of the cargo containment system (tank hatches,
drains, etc.)
X
Tank Cleaning with Portable Machines X
Purging cargo pump cofferdams / Blowing through Heating coils X
Any other task/ location where the risk of exposure has been
deemed to exist.
X
Spill response X
Purging cargo pump cofferdams / Blowing through Heating coils X
Deck watch X
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 10 of 46
3.2.3.6. Ship Checks Prior Arrival
The checks as per “Section 1” of the Company Checklist – “OP-Chem-04 Cargo Transfer Checklist”
must be carried out.
Exchange of Cargo Information Before Arrival
Master should communicate with parties concerned, through Agent if necessary, prior to arrival of vessel
at a berth or anchorage for intended cargo operation handling, tank cleaning and pre-wash, ballasting and
bunkering to exchange and acquire necessary information such as cargo readiness, cargo data, intended
cargo quantity, etc. and to give necessary information to the parties for safe and efficient operations.
(1) Vessel with Agent
1. ETA, draft, tugs, pilot and other port information.
2. Defects on vessel, which may affect port and cargo operation.
3. Sizes and number of cargo manifold connections.
(2) Vessel with pilot (Directly or through Agent).
1. ETA at pilot station, draft and others, which are required for safe manoeuvring of Vessel.
(3) Terminal (berth master / cargo surveyor) with Vessel.
1. Quantity, S.G., correction factor, temperature, special requirements for cargo.
2. Tank venting requirements and details of any vapour return lines required.
3. Tank environmental control requirements, e.g., drying and inert gas.
4. Check list, Terminal regulation, emergency plan, etc.
5. Detail of Terminal facilities (distance, elevations to shore tank, use of booster pump, etc.).
6. Number, and size of shore connection and estimated loading rate.
7. Depth of water at berth.
8. Information on weather or surroundings.
9. Terminal or Port Regulations on pre-washing of cargo tanks alongside the berth, and details of
reception facilities to receive slops (if applicable.).
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 11 of 46
10. Any other limitation of the Terminal.
11. Expected rate of transfer.
12. Declare last three cargoes of the nominated tanks to the shipper’s surveyor.
13. Tank Cleanliness requirements.
14. Security Level.
3.2.3.7. Ship Shore Safety Meeting
The ship staff (Master and/or Chief Officer), the men in charge of the terminal operation and Cargo
Surveyor must attend, agree and coordinate operational sequence and clarify terminal rules / regulations.
The operations usually agreed upon during a pre-cargo conference are:
- Cargo Sequence
- Cargo Quality
- Loading / Discharges Rates
- Ship or Shore Stop
- Standby time
- Signals and Communications
- Emergency Procedures
- Line Blowing / Pigging Arrangements
1. Any referenced procedures / agreements should be made in writing in remarks column of the ‘Ship-
Shore Safety Checklist’ which may also be recorded in any other mutually acceptable form in addition. In
either case, both parties must sign all such referenced procedures/agreements prior commencing the
cargo operation.
2. Additionally, confirm the following with the Cargo Surveyor:
a. Correct cargo name, nominated quantity
b. Shore tank temperature
c. Sampling requirement
d. Tank inspection requirement
3. Cargo calculation method, API / SG / Correction factor and tables
4. In case cargo heating or padding is required, obtain written instructions.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 12 of 46
Cargo Operations should not commence until Chief Officer and the Officer on Watch (OOW) have
ensured that pre-transfer checks have been completed.
Transfer Precautions
Checks Prior Transfer
Checks as per “Section 2” of the Company Checklist “OP-CHEM-04 - Cargo Transfer Checklist” must
be carried out.
Checks During Transfer
Checks as per “Section 3” of the Company Checklist “OP-CHEM-04 - Cargo Transfer Checklist” must
be carried out
Cargo transfer should be stopped immediately if any one of the following is noticed:
1. Emergency alarm being raised on the vessel.
2. Explosion / Fire in the terminal.
3. Leakage from cargo tank hose or connection.
4. Lightning in vicinity of the vessel / Thunderstorm.
5. Several tanks reaching topping up ullages at same time.
6. Breaking of mooring lines of own vessel or barge.
7. When there is danger of a moving ship hitting the vessel.
8. When there is a heavy or dangerous vapour accumulation on deck.
9. If weather conditions deteriorate.
10. In case of Doubt or it is considered that transfer is dangerous.
11. Ship / Shore Difference exceeds 5% of the loaded quantity.
The office will always support cargo rate slow down / stop page by vessel for reason of safety. Please
refer to Section 10 “Emergency ” for necessary action in the event of cargo spill.
The office will always support cargo rate slow down / stop page by vessel for reason of safety.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 13 of 46
Please refer to section 11 “Emergency “ for necessary action in the event of cargo spill.
CHECKS AFTER TRANSFER
Checks as per “Section 4” of the Company Checklist ““OP-CHEM-04-Cargo Transfer Checklist” must
be carried out.
3.2.4. CLOSED LOADING
General Information
“Closed Loading” contributes to:
- Prevent accumulation of vapour on deck.
- Prevent vapor emission to atmosphere when vapor return system is operated.
“Closed Loading” means cargo operations (Both Loading and Discharging) without recourse to opening
ullage and sighting ports. During closed operation, ships will require the means to enable closed
monitoring of tank contents, either by a fixed gauging system or by using portable equipment passed
through a certified vapour lock, intended for use with the type of equipment only.
The vapour displaced by the incoming cargo should be vented to the atmosphere through high velocity
vent valves (HVVV) or returned to shore through vapour return lines as in case of toxic cargoes.
Vessels shall comply with “Closed Loading Procedures” during Loading and Discharging
operations for all cargoes.
“Open Loading” of cargoes other than Toxic or Flammable cargoes is only permitted under
special circumstances if required due to unavoidable and valid reasons.
Master can only permit this if allowed by terminal or port regulations AND after carrying out Risk
Assessment and obtaining explicit permission from Office.
3.2.4.1. Closed Loading Without Vapour Return
1. Confirm all openings of tanks and purge pipes are closed.
2. Fit tank pressure gauges (compound) for monitoring tank pressure if vessel is not provided with a fixed
pressure sensing system.
3. Set cargo tank pressure alarms (Reference Section 1.38).
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 14 of 46
4. The loading should commence only after the Chief Officer has verified the cargo line up.
5. Monitor cargo level by closed gauging systems. (Fixed / Portable)
6. Use of sighting ports.
7. The duty officer should monitor tank pressure regularly.
8. Upon completion of loading, secure cargo line valves.
9. Disconnect cargo hoses.
3.2.4.2. Closed Loading with Vapour Return
1. Confirm all openings of tanks are closed.
2. Fit tank pressure gauges (compound) for monitoring tank pressure if vessel is not provided with a fixed
pressure sensing system.
3. The loading should commence only after the Chief Officer has verified the cargo and the vapour return
line up.
4. Set cargo tank pressure alarms & VECS alarm (Reference Section 1.3.8).
5. Open Vapour Return Valve of cargo tank as required.
6. Open Vapour return manifold.
7. Commence loading.
8. Monitor tanks to ensure that they are not pressurized or under-pressurized excessively.
9. The responsible officer should confirm with terminal, the flow of the vapour back to shore.
10. The deck ratings should monitor PV valve and manifold VRL compound pressure gauge. Any
abnormalities MUST result in suspension of cargo operation till the reason is investigated.
11. Monitor cargo level by closed gauging system (fixed or portable).
12. Use of sighting ports.
13. Upon completion of loading, close vapour valve first and then cargo valves.
14. Disconnect cargo / vapour hoses.
15. All connections to the common Vapour line should be isolated after completion of loading operation.
Note: The P&A Manual and VECS (Vapour Emission Control System)
Manual (if provided) is to be referred to and requirements complied with.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 15 of 46
3.2.4.3. Measurement Procedures - Ullaging
ALL CARGOES other than those MENTIONED UNDER COLUMN “G” (Open Venting) & “J” (Open
gauging) of Chapter 17 of IBC Code should be subjected to Gauging through approved vapour
lock system and utilizing closed gauging devices.
Grounding device: The grounding device must be used on the ‘Tank Gauging Station’, to ensure that
gauging device is necessarily grounded through the gauging station.
Sounding tapes / UTI tapes which can accumulate electro-static charges are NOT to be lowered in non-
inerted tanks with flammable static accumulator cargoes for up to 30 minutes after completion of
loading. This waiting period is not required for inerted tanks or for sampling to be done through full length
sounding pipe.
Cargo measurements are required to be carried out.
1. At the loading terminal (prior to, and after loading).
2. At the discharge terminal (prior to and after discharge).
Final ullages should be taken in conjunction with the shipper's representative (Surveyor).
Where remote level gauges must be used for gauging to comply with IBC code requirement. It is
necessary to ensure that remote level gauges are compared with portable level gauging devices for
accuracy. To minimize errors in measurements the following points should be noted:
1. Obtain and record Vessel's draught, trim and list taken immediately before commencement of cargo
measurement.
2. As far as possible the vessel should be upright and even keel at completion of loading.
3. Drain hoses or loading arms, and deck lines into tanks.
4. Ullages of all cargo tanks recorded accurately to 0.5 cm. Care must be taken to ensure the correct
ullage datum is being used and that, if there is movement on the surface of the cargo, a true mean ullage
is obtained.
5. When applicable suitable ‘float corrections’ must be applied in the cargo calculations.
6. Verify Reference ullages with empty tanks and markings at each tank.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 16 of 46
7. Determine and record the cargo temperature in each tank at least three levels top, middle and bottom
with an accuracy of about 0.5 Deg C.
8. Ascertain whether quoted as a density in air or in vacuum. In the chemical trade the density is given in
air with coefficient of thermal expansion.
9. The measured ullages must be corrected for ship's trim and list in accordance with the ship’s ullage
tables before extracting the gross quantity for calculation;
10. Corrections as applicable for the UTI being used must also be considered.
11. All results must be recorded on ullage report.
12. The times of sampling and final ullaging must be recorded in the time sheet.
Any ship shore difference of quantity must be addressed as per Annex II of this manual
3.2.4.4. Portable Gauge Operating Procedures
1. Before use, confirm the gauging tape and gauging station are cleaned.
2. Remove plug from the standpipe.
3. Fit portable gauge on vapour lock.
4. Operate as per maker’s instructions.
5. Compare readings of Portable gauge with Fixed gauge at frequent intervals.
6. The crew should wear necessary personal protective equipment as required for the cargo.
7. After usage, secure the vapour lock and thoroughly clean the tape.
3.2.4.5. Port Logs
As a minimum the following information should be recorded in the Port Log.
1. Time of Arrival at the Port, NOR Time.
2. Anchoring Times, if applicable.
3. Gangway down.
4. Time Surveyor, Loading master onboard.
5. Time of Ship-Shore Safety Meeting carried out.
6. Time of Tank Inspection, Tanks passed. Method of Inspection of the tanks.
7. Time cargo / vapour hoses connection, disconnection.
8. Time Samples taken, Samples passed, First foot / various sampling.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 17 of 46
9. Time of cargo commencement, completion, stoppages (if any).
10. Time of cargo tank change over.
11. Records of regular rounds taken on deck, moorings tended, etc.
12. Details of ballast water inspection through sampling points fitted on manholes.
13. Details of Ballasting Operations (details of pumps, tanks operated).
14. Time of any delays in berthing or cargo operations and party responsible for the delay.
15. Requests for reductions in the loading rates for topping off or rate reductions by the shore must be
recorded in port log.
16. Any pollution observed MUST be recorded and reported to the appropriate authority, nothing the
position and direction of drift. Such observations may be invaluable if the vessel is later accused of
causing pollution.
3.2.4.6. Protest Letters
The charterer, or the terminal on the charter’s behalf, has the obligation to provide such equipment and
conditions that allow the vessel to safety operate within charter-party commitment. If vessel’s
performance is hampered due to any shore restrictions, the Master shall issue a ‘Protest Letter’ using the
relevant form PC-1.
Some examples of issuing ‘Protest Letter’ are as below:
1. Free water in cargo.
2. Short Loading / Dead freight.
3. Slow Loading / Discharge.
4. Shore Delays.
5. Unavailability of cargo heating / inerting instructions.
6. Insufficient time for water settling.
7. Non receipt of set of cargo samples for the vessel.
8. Discrepancy Between Ship / Shore Figures.
9. Non availability of cargo Information / shipper specific MSDS.
10.Same Shore Line used for Multiple parcels.
11.Non receipt of Terminal Regulations.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 18 of 46
The Master shall ensure that ‘Protest Letter’ shall be signed by a shore representative before the ship
leaves the terminal. In cases where shore representative refuses to sign ‘Protest Letter’, a countersign of
local agents shall be obtained for forwarding same to the shore representative.
In the cases, where ‘Protest Letter is issued to the Master by the terminal, the Master shall accept ‘Protest
Letter’ stating ‘FOR RECEIPT ONLY’ and forward a copy to the charterers / managers and a non-
conformity is to be raised.
3.2.4.7. Preparing the Manifold
Care should be taken to prepare the manifold for transfer of chemical cargoes.
a. The manifolds to be used must be identified with the use of placards.
b. Jumpers and hard pipe connection must be made prior the transfer operation.
c. Pressure gauges must be placed on all manifold on shore and offshore sides. They should have a
valve or cock and not be fitted directly.
d. The crew and officers involved in manifold preparation must be well experienced.
e. Unused manifolds are blanked and drains are closed.
f. All cargo valves are to have light lashings available for use as positive indication that the valves are to
remain closed.
g. Gaskets in use on board should be made of a material suitable for the cargo being transferred on
board.
h. All flange connections must be fully bolted.
i. Appropriate PPE must be worn while engaged in any activity in the manifold area.
Additionally for transfer of toxic, flammable and corrosive cargoes:
a. Manifold connection flanges should be covered with hard pieces also known as “Spray shields” to
prevent a spray of cargo due to an inadvertent failure of gaskets.
b. Manifold connections with shore must be pressure tested to confirm integrity of the connection prior
transferring particularly toxic, corrosive and/or highly flammable cargoes like MDI, TDI, Phenol, Nitriles,
cyanide cargoes, propylene Oxide etc.
Additionally for transfer of Solidifying cargoes:
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 19 of 46
a. Ensure that the manifold arrangement is such that there are minimum dead ends in the cargo circuit so
as to avoid problem of blocked lines / sections.
3.2.4.8. Lining up for Operations
Primary Check
Chief Officer must supervise the initial setting of lines, tanks and valves vent risers and vapour lines.
Prior cargo operations commence he must verify that:
1. Cargo tanks and lines, reducers and cargo hoses have been properly lined up.
2. Flanges of removable parts such as reducers, cargo hoses, elbows are properly fitted and tightened
and that all open flanges are covered with blank flanges.
3. All heating coils not in use have been blown through with nitrogen or dry air and blanked.
Secondary Check
A second independent check of the above systems for the proposed operation is to be carried out by a
responsible person. Valves must be checked physically and visually where required to ensure the blanks
and valves are shut.
Operation Of Valves
The manipulation of tank, deck line and pump room valves is the responsibility of the Chief Officer
assisted by other Officers.
Cargo valves shall be operated by the duty ratings and cross checked by the Duty Officer or other
responsible person designated by the Chief Officer.
Following are general guidelines to be kept in mind: a. Keeping Valves Closed: All cargo system valves, ballast and vent valves when not in use must be kept
closed.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 20 of 46
b. Manifold Valve: Manifold valve must be opened last – just before the transfer begins. If the transfer is
stopped, even for a short while, the manifold valve must be closed. Manifold should be monitored
throughout cargo operations.
c. When handling Highly Toxic / Highly Corrosive cargoes, the person monitoring the manifold should
stand at a safe distance to minimise risk of exposure to cargo.
d. Changing Tanks: When changing tanks, the valve for the next tank must be opened before closing the
valve of the tank to be shut off.
e. “Walking Back” Fully Opened Valves: When a valve is opened fully, it should be “walked back” about
one turn to prevent it from jamming open.
f. Stopping Transfer: Flow of cargo into the vessel must be stopped by shore valves. Flow of cargo or
ballast out of the vessel must be stopped by vessel valves.
g. Close & Open valves slowly to avoid pressure surge in pipelines.
3.2.4.9. Common Line Handling
1. Common line is useful for handling cargoes of the same grade instead of connecting jumpers on the
manifold.
2. It minimizes the risk of cargo leakage from connections or cargo hoses and improves safety of cargo
operation.
3. It improves the cargo transfer rate and simplifies cargo handling.
4. Vessel should as far as possible use common line for discharging Toxic / Corrosive cargoes.
5. At some terminals cargo transfer by flexible hoses is not allowed. Under such circumstances, vessel
MUST use common line.
6. Certain cargoes do not meet flexible hose compatibility and transfer is required to be carried out by
common line.
7. Common line is used if adequate hoses reducers, spool pieces or jumpers are not available on board.
8. Common line usage for lub oil additives, solidifying cargoes and polymerizing cargoes should be
avoided as far as possible.
Refer “Cargo Transfer Checklist (OP-CHEM-04)” for common line precautions during cargo transfer.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 21 of 46
Record of use of Common Line is to be maintained using the form " Cargo History of Common
Manifold."
3.2.4.10. Pressure Surge
A pressure surge is generated in a pipeline system when there is any change in the rate of flow of liquid
in the line. The surge can be dangerous if the change in the flow rate is too rapid.
If the total pressure generated in the pipeline exceeds the strength of any part of the pipeline system
upstream of the valve, which is closed, there may be a rupture leading to extensive spillage.
The potential hazards of pressure surges (shock pressure, known as water hammer or liquid hammer)
resulting from rapid operation of the valve must be emphasized upon all personnel involved in cargo
operations.
The following precautions should be taken to avoid pressure surge during cargo transfer:
1. Shut down procedures should be in place, pumps to be stopped or pump discharge valves shut before
manifold valves or valves in the shore pipeline are shut.
2. During loading, when the flow is diverted from one tank to another, the valves on the tank about to
receive cargo should be fully open before valves of tank to be isolated are shut.
3. On completion of loading, the flow should be stopped by the terminal using shore valves and not by
shutting of ship’s manifold.
4. The closing timing of all hydraulic and pneumatic valves must be tested and set to over 30 secs to
avoid surge pressure during valve operations.
3.2.4.11. Overfill Protection
High level and over fill alarms should be tested prior every cargo transfer operation. These should be kept
operational for cargo transfer operations. The crew on deck should be familiar with these alarms and
must notify the CCR in case of activation. The activation of these alarms should be anticipated and
immediate investigation must be carried out to find the reasons for activation. If additional time is required
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 22 of 46
to continue the investigation, then the transfer operation must be stopped. Under no circumstances
should the activation of high level or overfill alarm be ignored. The high level or over fill alarms must not
be bypassed. Master and Chief Officer should leave explicit instructions in the cargo operation plan about
action to be taken in case of inadvertent or unexpected activation of high level or over fill alarms.
3.3. SECONDARY MEANS OF PRESSURE / VACUUM RELIEF
Secondary means of allowing full flow relief of vapour, air or inert gas mixtures shall be provided to
prevent over-pressure or under-pressure of the tanks in the event of failure of the primary venting
arrangements during loading, ballasting and discharging. Secondary venting may also be provided by the
use of pressure sensors fitted in each tank to monitor the pressures in the tank atmosphere. The pressure
sensors must provide visual indication of tank pressure and must be fitted with an audio visual alarm in
the cargo control room. In order to prevent inadvertent operation there shall be a clear visual indication of
the operational status of the inert gas valves.
Following pressure alarm settings are recommended for the vessel fitted with pressure sensors in each
tank and having an audio visual indication in the CCR. Following is the recommended pressure alarm
settings for individual tank sensors.
While operating in inerted mode
The high pressure alarm should be set at 10% higher than the normal opening pressure of the PV valve.
Low pressure alarm: +100 mm WG.
While operating Vapour return mode
Individual tank pressure alarms The high pressure alarm should be set at 10% lower than the normal
opening pressure of the PV valve.
Low pressure alarm: +100 mm WG.
Additionally as per CFR 46.39.13-20 requires that the vessel fitted with Vapour collection system should
be provided with a sensor in the main vapour collection line to monitor the pressure within the vapour
transfer line. In order to prevent release of the vapour into the atmosphere during a transfer the alarm for
the main line pressure must be set as given below.
High pressure alarm should be set at 10% below the normal operating pressure of the PV valves.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 23 of 46
If tanks are inerted the low pressure alarm must be set such as to prevent vacuum in the tank
recommended value for setting is at 0.144 psig (101mm WG) if the tanks are non inerted then the low
pressure must be set at the lowest value at which the vacuum valves normally operate.
Non Inerted tanks
High and low pressure alarms should be set at 10 % outside the normal opening pressure of the pressure
and vacuum valves, i.e. 10% above the opening pressure of the pressure valve and 10% below the
opening pressure of the vacuum valve.
The alarm setting may only changed with master’s permission and any change should be notified all
concerned personnel. Prior every cargo operation the pressure alarm settings must be inspected, verified
for a suitable value and recorded suitably as per management of change process.
3.4. CONNECTION / DISCONNECTION OF SHORE HOSES AND ARMS
Usually, shore hose connection / disconnection is done by the terminal. The vessel must have sufficient
crew members to perform shore hose connection / disconnection if required.
A responsible vessel officer must supervise any connecting or disconnecting of cargo hoses and
loading arms.
The officer must ensure that:
1. Personnel engaged in connection of cargo hoses are wearing the PPE Level applicable for the
cargo being handled.
2. The hose or loading arm is in good condition, free from any cargo residues and long enough to
allow for vessel movement due to tide and changes in draft or trim.
3. Hose is suspended with saddles or straps so that the bend radius is never less than 12 times the
hose diameter.
4. Falls or slings which support the hose, are made fast to a bit or cleat, never a gypsy head.
5. Sufficient numbers of reducers, gaskets, nut / bolts must be kept readily available on board for
manifold connection.
6. All bolts are used for flanged connections. Only one gasket should be used each time the
connection is made.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 24 of 46
7. All bolts must have at least 3threads visible after the nut is fully tightened.
8. As far as possible, use of flexible hoses on manifold as jumpers is to be avoided in order to prevent
any leak / spill of the cargo. When absolutely necessary to use flexible hoses, such hoses should
be properly supported and tested by air / nitrogen pressure for leakage prior cargo operations.
9. After completion of cargo operation,Nitrogen or compressed air should be used to displace
products in cargo hoses or loading arms whenever possible.
10. After disconnection, cargo hoses must be secured using blank flange and connected using all nut /
bolts.
11. All cargo hoses belonging to the vessel must be cleaned and gas freed before stowing.
3.4.1. Line Flushing
For certain sensitive cargoes the cargo line may be flushed in to slop drums prior line samples are taken.
Care should be taken to flush one line at a time. Surveyors should be consulted to confirm the method
and necessary quantity for line flushing, sampling method and positions. An agreement must be reached
on the cargo quantity required for flushing and whether such flushing is to be stopped by ship’s order or
by shore order. The drums of slopped product and the cargo collected during the line flushing should be
landed back to the terminal. An agreement should be made with the terminal during the pre transfer
meeting to this effect.
3.4.2. Line Draining / Clearing
Line clearing is required to be carried out:
1. On completion of loading (each line system).
2. After any cargo transfer (from tank to tank).
3. After cargo recirculation operation.
4. After part discharge from any tank(s).
5. On completion of discharging each line system must be cleared.
6. After stops in the cargo handling which may cause line solidification.
On completion of loading, the ships cargo deck lines should be blown back into appropriate cargo tanks
to ensure that thermal expansion of the contents of the line can not cause leakage or distortions. The
hoses or arms and perhaps a part of the pipeline system between the shore valve and the ships manifold
are also usually drained in to the ships tanks. Sufficient ullage must be left in the final tanks to accept the
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 25 of 46
draining of the hoses or arms and ship or shore lines. On completion of discharge ship’s cargo lines
should be blown ashore.
When draining is complete and before hoses or arms are disconnected, ships manifold valves and shore
valves should be shut and the drain cocks at the vessel’s manifold should be opened to drain in to fixed
drain tanks or portable drip trays (except for toxic / incompatible cargoes). Cargo manifolds and arms or
hoses should be securely blanked after being disconnected and prior lowering to the terminal. The
contents of portable or fixed drip trays should be transferred to a slop tank or other safe receptacle and
later disposed in accordance with applicable MARPOL requirement with relevant entry in ‘Cargo Record
Book’ under Code ‘K’.
3.4.3. Precautions when Tanks are Close to 98% Full
When lines are being drained into a tank which is close to 98% full extra care should be exercised to
ensure that overflow does not take place. In particular following precautions should be taken:
1. Confirm the quantity that is contained in the line and ascertain that tank has sufficient ullage to take the
quantity without reaching 98%.
2. Man standby at manifold to close the valve if required.
3. An officer monitoring the High Level / Overfill Alarm and Remote Ullages.
4. Proper communication between ship / shore.
5. Draining should be done under gravity as far as possible to avoid excessive pressure / volume.
6. This operation should not be done when carrying out other critical operations such as topping off tanks,
stripping, connection / disconnection, etc.
Note: If vessel does not have sufficient ullage to safely take the drained quantity, then lines
should be blown back to shore.
3.4.4. Procedure for Clearing of Shore Hoses And Ship’s Cargo Pipe Lines
Effective clearing of lines after transfer of cargo is an essential process. Lines if cleared effectively this will
prevent cases of loss of primary containment, subsequent contamination of the cargo remaining in the
lines, Freezing of line for solidifying cargoes and damage of valves, seat and pipelines due to expansion
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 26 of 46
or contraction of cargo remaining in the line post cargo transfer. Clearing of lines can be carried out with
the use of Compressed air or Nitrogen. The operation should be controlled and supervised by a
responsible officer.
While Compressed air is suitable and easily available on board the vessel however it is not a suitable
medium to clear lines while handling flammable products and products which are padded with nitrogen for
quality reasons and products which are sensitive to oxygen. In any case whenever compressed air or
Nitrogen is used for line clearing the following precautions should be strictly observed in order to avoid
the possible creation of a hazardous static electrical charge or mechanical damage to tanks and
equipment:
1. The procedure to be adopted must be agreed between ship and terminal.
2. There must be adequate ullage in the reception tank. There is a risk of over flow and over
pressurization when Nitrogen or compressed air is blown into a loaded tank.
3. To ensure that the amount of compressed air or nitrogen is kept to a minimum, the operation must be
stopped soon as the line has been cleared.
4. The line clearing operation must be supervised by a responsible deck officer. The tank pressure should
be continuously monitored. The nitrogen when received from sources ashore, this may be supplied at
excessive rates. The flow must be strictly controlled to prevent overflow and over pressurization of the
tanks.
5. Shore hose and ship’s manifold must be blanked soon after disconnection after the transfer operation.
3.5. LINE BLOWING
This operation is carried out while the tanks and lines are empty to verify that the lines are free of water
and debris after tank cleaning and gas freeing. On some occasions this operation is carried out using live
steam to dry out and clean the line.
1. Care should be taken while line blowing with air, nitrogen or steam since it may cause excessive tank
pressure and hence tank openings are to be kept open.
2. Lines are first blown out on deck through the drain pipe before it is blown into the tank.
3. All concerned persons should wear appropriate PPE.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 27 of 46
4. The supply line should be crack opened and checked for pressure. For ships fitted with compressed air
/ nitrogen reservoir, drain the condensate and confirm the availability of adequate pressure in the
reservoir tank.
5. One person should standby at tank valves and another person should control supply inlet near
manifold.
6. Line blowing should be carried out in a way that tanks and lines to be blown are carried out one by one.
7. Secure all valves after completion of line blowing.
3.5.1. Procedures for Line Blow Through Operation (With Pig)
When carrying out Line blow through operation with pig, in addition to all precautions described in above
section, the following precautions are to be followed:
A. The system should be designed so that the pig seals in the line during the operation and in the
trap once the operation is complete. A restrictive orifice sized to cargo venting capacity may also be used.
Sensors and alarms may be installed to detect ‘blow by’ and pig disintegration. Sight glasses and
operator monitoring personnel improve the ability of detecting problems in line clearing operations.
Procedures must be in place to insure the correct pig (type and size) is used.
B. The pig should be introduced at the pig launcher. Care must be taken to ensure that the pig is
properly positioned in the launcher. The pressure should be equalized between the line and the pig
launcher.
C. The vessel should open its manifold valve part way. Compressed gas should be introduced into
the launcher, behind the pig, to begin moving the pig through the line. Personnel should monitor the flow
of cargo and the movement of the pig throughout the operation and communicate this information to each
other. Once the pig enters the pig trap, the shore valve and vessel manifold valve should be closed
immediately. The line and hoses from shore to vessel manifold should then be cleared directly as
described previously.
3.6. SHIP TO SHIP (STS) TRANSFER OPERATION
Ship to Ship transfer’ is to be carried out in accordance with approved ‘STS Plan’ of the ship.
Refer to “STS Transfer Checklist” for associated precautions.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 28 of 46
In addition below is a guideline for Chemical tankers engaged in ship to ship transfer.
The ship to ship (STS) transfer of cargoes carried on chemical tankers is a frequent operation. The
guidance covers cargo transfer operations in open waters and roadsteads, either between two chemical
carriers, or between a chemical carrier and barges. It is not intended to cover discharge to a barge from a
chemical carrier already at a terminal, because that is considered to be normal cargo handling under the
supervision and control of the port or terminal authorities.
Below guide provides advice about special equipment necessary, and preparation of contingency plans
for dealing with emergencies. In general, observance of the procedures followed when handling cargo
alongside a terminal will ensure safe ship to ship transfers. However, an important additional task is
careful pre-planning of the operation, noting instances where shore provision of materials or labour for
handling equipment is normal terminal practice, and identifying on board or external sources of material
or personnel to perform those duties during the ship to ship operation.
Responsibility
In general, it is the responsibility of the ships' operators and agents to obtain any permission necessary
for a ship to ship transfer operation, especially if the transfer area is within the jurisdiction of a port
authority.
The general principles of a transfer, the area in which the transfer will take place, and the compatibility of
the ships should follow the advice in the STS Guide, with safety always the primary consideration.
Ship operators or the local agent should advise a master about documentation requirements, especially
customs documentation, well in advance of the transfer. It is normal for the quantity transferred to be
agreed between masters of both ships in accordance with operator's instructions.
When preparing for a ship to ship transfer the two masters involved should agree at the earliest
opportunity on every aspect of the transfer procedure, and agree which person will be in overall advisory
control of the operation (this may be one of them or an experienced STS superintendent). At all times,
however, each master will remain fully responsible for the safety of his own ship, its crew and its cargo,
and must not permit safety to be jeopardised.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 29 of 46
Communications
The STS Guide gives advice on establishing communications at the earliest opportunity, and provides an
example of an initial voyage instruction. Satisfactory communication between the two ships involved is an
essential requirement for a successful ship to ship transfer operation. Neither approach and mooring, nor
unmooring, should be attempted until satisfactory communications are established, and if during cargo
operations there is a breakdown of communications on either ship, all operations should be suspended
until they are satisfactorily restored.
Navigational warnings
The person with overall advisory control should arrange for broadcast of a navigational warning about the
transfer, as described in the STS Guide, and should arrange for its cancellation on completion of the
operation.
Weather conditions and limitation It is impracticable to lay down the limits of weather conditions under which STS transfer operations can
safely be carried out. All available weather forecasts for the area should be obtained before the operation
begins. Thus any decision to proceed will be taken in the light of best available knowledge.
Pre-transfer preparations on each ship
Preparations on each ship in readiness for the operation, the approach of the ships to each other,
berthing and mooring of the ships and safety procedures when alongside, are all well described in the
STS Guide. When preparing cargo loading and discharging plans, due regard should be given to ensuring
that adequate stability is maintained, hull stresses remain within sea-going limits, and that free surface
effects are kept to a minimum throughout.
Remember that normal shore resources will not be available and that prior assessment will help to avoid
incorrect decisions that could compound an emergency and increase the peril for one or both ships.
The cargo operation should be planned and agreed between the two ships, and should include
information on the following, where applicable:
1. Quantity of each grade of cargo to be transferred, and the sequence of grades.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 30 of 46
2. Cargo data from data sheets, and copies of the data sheets if available.
3. Details of cargo transfer system to be used, number of pumps and maximum pressure.
4. Initial, maximum and topping off pumping rates. The discharging ship should be informed by the
receiving ship of the flow rates required for each of the different phases of the cargo operation.
5. Notice of rate change, and transfer shutdown procedures. If variations in transfer rate subsequently
become necessary due to circumstances on one ship, the other should be advised accordingly.
6. Emergency and spill containment procedures.
7. Watch or shift arrangements.
8. Critical stages of the operation.
9. Local and government rules that apply to the transfer.
Cargo transfer operations
When the two ships are securely moored, and before cargo transfer commences, the pre-transfer checks
should be satisfactorily completed . In addition, attention should be given to completion, as far as
practicable, of the appropriate Ship / Shore Safety Checklist .
Hose strings should be of sufficient length to avoid over-stressing and chafing throughout the cargo
transfer. To establish the correct hose length, changes in relative freeboard and ship movement must be
taken into account. Only hoses in good condition and suitable for the cargo to be transferred should be
used. The agreed transfer rate should not exceed the manufacturer's recommended flow rates for the
cargo hoses.
Vapour return and vapour balance between ships during an STS operation can be problematic. Its main
advantage will be to limit the need for vapour release to atmosphere, and crew exposure to the vapour.
But attention must be given to provision of a flame arresting arrangement. For some cargoes-specified in
the IMO Codes, vapour return is mandatory, and STS operations will be dependent on provision of
correct vapour return equipment.
Throughout cargo operations, the discharging ship and the receiving ship should each station a
responsible person at the cargo manifold area to observe the hoses and to check for leaks. In addition,
throughout the cargo transfer, the discharging ship should station a responsible person equipped with a
portable radio at or near the cargo pump controls to take action as required. Regular transfer rate checks
and comparisons should be made between the two ships, and the results logged. Any differences or
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 31 of 46
anomalies revealed should be carefully checked, and if necessary cargo operations should be suspended
until the differences are resolved.
During cargo transfer, appropriate ballast operations should be performed on both ships in order to
minimise extreme differences in freeboard ' and to avoid excessive trim by the stern. Listing of either ship
should be avoided, except as required for cargo tank draining on the discharging ship.
Regardless of the type of ship, any ballast which is discharged overboard should be clean. All other
ballast should be retained on board or transferred to the discharging ship.
Completion of cargo transfer
After completion of cargo transfer, all hoses should be drained into the receiving ship prior to
disconnecting. Disconnecting of cargo hoses should receive careful attention, as it is a procedure not
usually undertaken by ship's personnel. Cargo manifolds and cargo hoses should be securely blanked.
Relevant authorities, if any, should be informed of completion of cargo transfer and the anticipated time of
unmooring. Any navigational warning issued should be cancelled.
Ship to ship transfer using vapour emission control systems - chemical tankers procedure
Vapour Balancing
Before carrying ship to ship transfer operation using VEC systems reference is to be made to the
operational guidelines contained within ISGOTT, ICS Chemical Tanker Safety Guide and other applicable
reference publications.
The technique is properly described as Vapour Balancing Use of Inert Gas for oxygen dependent
inhibited cargoes may be dangerous (e.g. Styrene Monomer). IBC code requirements for specific cargoes
to complied with. The vessels VECS manual requirements are to be complied with.
Before commencing transfer the following operational precautions must be complied with as a minimum
for inerted tanks and non inerted tanks as applicable.
* At least one of the vessels must be able to permanently monitor the oxygen content of the vapour
stream. The sample point must be close to the manifold and audible and visual alarms are to be available
should the oxygen content exceed the agreed value.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 32 of 46
* The oxygen content of all tanks in the common system is to be maintained at a level no higher than the
agreed value.
* The vapour transfer hose is to be purged of air using inert gas or nitrogen until the oxygen content is
below the agreed value before transfer commences.
* Vapour manifold valves are not to be opened until the receiving vessel system pressure exceeds that
of the discharging vessel system pressure.
During the Cargo Transfer: * For inerted system, operations are to be terminated, if the oxygen content of the vapour stream
exceeds the agreed value. Operations are not to be resumed until the oxygen content in the receiving
ship has been reduced below the agreed value.
* There is to be frequent monitoring of both ship’s IG pressures with cross comparison on a regular basis
and at least hourly. Transfer volumes are to be compared on the same basis.
* No air is permitted to enter the tanks of the discharging ship at any time
* The guide lines contained in the OCIMF Ship to Ship Transfer Guide (Petroleum) and ICS Chemical
Tanker Safety Guide Ch 5.14 shall be complied shall be adhered to for the STS operation.
3.7. CARGO LOADING
Condition of Tank Prior Loading
Cargo tanks must be cleaned to the standard necessary to meet the requirements for the next cargo. The
requirements for tank cleaning should obtain from the load port surveyor prior arrival in port. The last
three cargoes carried in each nominated tank should be declared to the shipper prior vessel’s arrival in
port. The master should not present the tanks for inspection until he has ascertained that the nominated
tank meet the shippers requirements. The tanks must be prepared as required and the charterers should
be advised of the progress of the cleaning and time required for the necessary preparations. The
operation team in the company should be advised of the progress of cleaning. As an operational standard
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 33 of 46
practice in the absence of any specific tank cleaning instructions received from the Charterers cargo
tanks are to be cleaned at the earliest available opportunity to water white standards.
Refer to “Section 4” for further guidance on tank cleaning.
Tank Inspection Prior Loading
1. The chief officer will accompany the cargo surveyor to ensure agreement that tanks are empty and fit
to receive the cargo.
2. Prior tank inspection, the Chief Officer must ensure, tank lines / vents and drains are blown through
and empty.
3. Drop and discharge valves should be left open.
4. In case tank entry is required for tank inspection, comply with Enclosed Space Entry Procedures.
5. Approved flash lights, shoe covers and cotton gloves necessary for tank inspection should be prepared
prior vessel arrives in port.
6. Care should be taken to ensure there is no formation of sweat in the tank.
7. Proper record of inspection procedure and timings should be maintained on board.
8. The reference heights of empty tanks should be carried out prior every loading.
9. The ‘Clean Tank Certificate’ must be obtained from the cargo surveyor prior commencing loading
operation.
3.8. LOADING RATES
The loading rate should always be agreed during the Ship-Shore Safety Meeting based upon the vessel
type, pipeline’s diameter, number and specific grades being handled, Static Electricity hazards, venting
capacity and P&A manual. The vessel should always request the optimum rate that it could safely handle
and issue a letter of protest if such rate is not supplied.
3.8.1. Cargo Loading Procedures and Precautions
The procedures and precautions for the cargo loading operation are to be documented in the “OP-CHEM
01 Cargo operation and Tankcleaning plan.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 34 of 46
Pressure Loading
Loading Overall (Splash Filling / Free Fall Loading)
Start of Flow
1. The manifold area should be monitored during the entire transfer operation.
2. Ship staff must collect samples of the first flow prior the ship’s manifold valve is opened. Only if
satisfied with the quality of the product should it be allowed to enter.
3. Loading should start at a slow rate.
4. The Chief Officer should check all tanks including empty ones to ensure that cargo is entering into the
correct tanks properly and that there is no leakage from the lines, into pump rooms, cofferdam or onto the
sea.
5. Thereafter regular checks must be made to ensure that the cargo system is free of leaks until
completion of the entire operation.
6. When all checks have been made and the operation is found to be in order, the loading rate may be
increased gradually to the agreed maximum, taking into account the following:
a. Working pressure of ship’s lines and hoses being used.
b. Capacity of vapours or vent lines.
c. Capacity and the required ullage in cargo tanks.
d. Nature of Cargo.
3.8.2. Control of Flow
When loading two or more tanks simultaneously with the same grade of cargo, the following should be
practised:
1. The flow of cargo to tanks must be controlled by the tank delivery valve, or manifold valves of specific
tanks, whichever is applicable (unless loading overall).
2. Such valves must not be closed completely or rapidly unless another tank is open to receive the flow.
Shore personnel must be instructed to slow the loading rate as per the agreement when finally topping off
tanks.
If the high level alarms are activated at an unexpected time, the loading operation must be stopped and
the matter should be investigated and corrected prior resumption of loading operation.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 35 of 46
Loading rate into the tank must be reduced prior topping off. Tanks where loading has been completed
should be isolated from others by two (2) valve segregation. On completion of loading the cargo, the flow
must be stopped on shore and not by shutting vessel's valves.
3.8.3. Progress of Loading
The Chief Officer and the officer on watch must always be vigilant whether the loading operation is
progressing in a smooth, safe, secure and efficient manner and carry out the following:
1. Ullages, tank temperatures and tank pressure, transfer rate must be continuously monitored and
recorded.
2. The quantity obtained by measurements using fixed level gauges should be cross-checked at regular
intervals using portable means like UTI tapes and recorded.
3. Loaded quantity, loading rate and estimated time of completion of loading should be calculated and
recorded.
4. If there is a large discrepancy in loading rates from those calculated at the previous periodical
measurement or the loading plan, the officer on watch should enquire about the reasons from the
responsible person on the shore / barge and inform the chief officer and master accordingly.
5. Ship shore quantity should be compared at regular intervals. Should a difference exceeding 2% be
observed, the chief officer should be notified. The difference must be investigated and the terminal
notified. If the difference exceeds 5%, loading must be stopped at once and chief officer should be
informed.
6. The officer on watch should keep periodical contact with the shore or barge representative as well as
crew members in charge of the manifold or engine room.
7. The stop ullages must be recalculated closer to completion with the current temperature of the cargo.
8. Stress and stability must be calculated at regular intervals and compared with the cargo operation plan.
Any significant variation must be brought to the knowledge of Chief Officer.
9. Chief Officer must present himself in the CCR during any critical stages of transfer. Critical
stages are usually Starting / Stopping cargo, Topping off, Line clearing, Nitrogen Purging / Padding Etc. If
Chief Officer is unable to be present due to rest hours or other requirements, Master shall be present in
lieu.
10. During loading operations any delays or stoppages must be immediately notified to the chief officer
and the master.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 36 of 46
11. Duty officer must immediately notify Chief Officer or Master, if he cannot understand any instructions
from shore due to language barriers or lack of clarity.
3.8.4. Topping off Procedures
The following points are to be considered during “topping off”:
1. The pre-loading meeting must include written agreement on the arrangements and notice required for
"topping-off". The number of valves to be closed during "topping-off" should be kept to a minimum.
2. Communications - both internal & external are verified to be in order. Terminal must be advised prior
tanks are topped off.
3. When required, additional personnel must be mobilized prior the topping operations.
4. The loading rate should be reduced to a safe level as per the initial agreement. This will require a
request to the shore to reduce the rate and shall take into account time required to effect such reduction.
Ship tank valves should not be used to reduce the rate as this can lead to pressure surges or excessive
pressure in the system.
5. Attention should be paid to any activation of the high level alarms during topping off. Tanks must be
topped off to a stage where overfill alarms are not activated. So that any inadvertent increase in level
can be detected.
6. Remote level gauges should be used for static accumulator cargoes. Where permitted in case of non
static accumulator cargoes portable UTI / MMC ullage gauges should be used for "topping-off". For static
accumulator cargoes adequate relaxation time should be allowed prior use of portable devices.
7. The proper functioning of level gauges should be verified from time to time during the operation.
8. Where fitted sighting ports should also be used effectively in addition to UTI / MMC ullage gauges.
9. When handling toxic cargoes if the UTIs available on board are not certified for closed use, then
remote gauging alone must be used for monitoring the level of the tank.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 37 of 46
10. The vessel is kept upright as far as possible during topping operations and thereafter until completion
of loading.
11. Tanks not being loaded and tanks which have already been loaded must be frequently checked for
any change in level.
12. The final stages of tank filling should be well staggered to allow one tank to be “topped-off" at any one
time. After "topping-off" individual tanks, master valves should be shut, where possible, to provide two
valve separation.
13. One tank in each grade should always be kept slack as a "Dump tank". If a valve failure or major leak
is experienced, such that a tank being "topped-off" cannot be closed off, the availability of a "crash tank"
will provide space to divert the flow during an emergency reduction in rate or complete stoppage. The
"Dump tank" would always be the last tank to be loaded.
14. On completion of loading, the flow must be stopped on shore and not by shutting vessel’s valves. All
the vessel’s valves must be shut thereafter.
3.8.5. Cargo Calculation
a. After completion of loading, all efforts should be made to determine cargo quantity as accurately as
possible.
b. If practicable, cargo temperatures must be obtained from at least two levels. When the gauging has
been done in stream or in unprotected waters where, due to wave action the vessel had not been steady,
suitable remarks should be inserted in the ‘Ullage sheets’ and/or ‘Statement of Facts’.
c. The vessel’s final figures should be compared against final shore figure or ‘Bill of Lading’ figure.
d. The Master MUST issue ‘Letter of Protest’ if there is difference between these figures.
e. In case of significant difference between ship and shore figures, manual gauging shall be carried out to
verify remote gauge readings.
f. The reporting to the charterers and Office must be carried out in case the difference is exceeding the
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 38 of 46
tolerance limit as given in the charter party or charterer’s or owners instructions, whichever is less. In
case there are no specific tolerance limits given, then a figure of 0.3% is to be taken as standard.
3.8.6. Cargo Quality
1. To monitor the quality of the cargo, samples must be taken as mentioned in Section 5.1 of this
manual.
2. When loading fine grade Chemicals, first foot sample analysis is carried out by the surveyor at the load
port. If sample fails this analysis, a fresh sample should be drawn from the tank without loading any
further and analysed. If the second sample also fails the test, Office must be informed for arranging P&I
attendance. Second Foot / additional cargo is not be loaded without office approval.
3. The master must ensure that cargo is loaded at its normal loading temperature. If he has reason to
believe that cargo is not being delivered to the vessel at correct temperature and it may affect the quality
of cargo onboard or cause damage to the tank coating or ship’s structure, he must issue ‘Letter of Protest’
and immediately inform Charterers and Office.
4. Clean petroleum product cargoes and base oils, which are not miscible with water, should be checked
for presence of free water using UTI tapes / oil interface detector upon completion of loading. If any water
content is noticed, it must be accounted for in the Ullage report to determine the exact quantity of the
cargo. The Master should issue ‘Letter of Protest’ for presence of free water in the cargo. For base oils,
dead bottom samples shall be drawn to detect presence of suspended water.
5. Some sensitive chemicals are loaded in tanks after nitrogen purging of the tanks. It must be ensured
that O2 content of tank atmosphere is checked after the purging is complete and it is found satisfactory to
load the cargo. If not, matter must be taken up with the terminal to get tank atmosphere to correct
condition before accepting the cargo. In case vessel is facing a problem in achieving this, the charterers
and Office must be informed immediately for further action.
6. Padding of tanks – The Master shall issue letter of protest if tanks are padded at loadport without
written instructions.
7. At discharge port, if cargo sample is alleged to be off specification, a re-analysis should be requested
and Charterers and Office must be consulted immediately for taking appropriate action.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 39 of 46
3.8.7. Adding Substances to the Cargo
Adding any substance to the cargo onboard should not normally be accepted as improper mixing may
result in the necessary result not being achieved. Before adding any substance to the cargo, approval
from Owners / Charterers and Office must be obtained. LOI will be required by Owners in this case.
Conditions for adding substances to the cargo are as follows:
a. Adding water to the cargo for dilution.
b. Adding additive to the cargo for stabilization / colour / legal purposes.
c. Blending of different grades.
d. Adding inhibitor for safer handling of the cargo.
The ship staff should only facilitate the addition of substances to the cargo as advised by the charterer but
not physically add themselves.
Blending of cargoes at sea is prohibited.
3.9. DISCHARGING
Discharging Procedures and Precautions
Procedures and precautions to be followed during discharging are to be documented in the “OP-CHEM-
O1 Cargo Operation & Tank cleaning Plan ”.
Emergency Stops
All Deck Officers and ratings must be fully conversant with the procedures for stopping cargo pumps in an
emergency. Such devices should be regularly tested and records of same maintained. The terminal
regulations / procedures for Emergency Stop Device (ESD) must be discussed and clearly explained to
all concerned crew members prior commencing cargo transfer operation. In case of an Emergency if
cargo operations are required to be stopped then crew members should do so promptly.
An emergency signal should be agreed during the pre-transfer agreement between the Ship and the
Terminal. In case the signal is initiated at any point of time during the operation, cargo operations should
be immediately stopped.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 40 of 46
Discharge Pressure Restrictions
Any discharging restriction placed by the terminal must be included in ‘Ship Shore Safety Checklist’ and a
suitable ‘Letter of Protest’ should be issued to the terminal for ‘SLOW DISCHARGING’ to avoid future
disputes with charterers.
When discharge pressure limitations are imposed, on no account should the discharge pressure exceed
the maximum stated by the shore, otherwise bursting of the hoses may result. Pumping log indicating the
hourly discharge rate and manifold pressure should be filled for every grade and port, such logs should
be endorsed by loading master or terminal representative.
3.9.1. Ullaging / Sampling Prior to Discharge
Before commencing discharge of cargo, the cargo surveyor together with the Chief Officer will check the
ullages of the tanks to be discharged to calculate cargo quantities to be discharged. The method used for
calculating specific density at the disport must be the same as the method used in the load port.
These figures must be compared to the loading port cargo figures. In the case of a significant
discrepancy every effort must be made to establish the cause, including checking of void spaces and re-
taking of temperatures.
Rate of Discharge
The vessel should be ready to discharge on completion of checking cargo figures. Any delay encountered
in this should be protested against.
Charter Parties usually contain a provision guaranteeing a certain rate of discharge, normally pressure of
100 psi (7 kg/cm2) at ship’s rail or discharge of entire cargo within 24 hours. Some installations are
unable to receive at this rate resulting in lay time being exceeded. Discharge should be carried out at
maximum achievable rate permitted by terminal. To establish proof of excess time used and thereby
ensure payment of demurrage, a written protest should be made as quickly as possible in order to give
the installation opportunity to improve on their reception.
Upon commencement of discharge, a cargo pump discharge log is to be started up and pressure
maintained at manifold is to be noted accurately and regularly at intervals not exceeding one hour.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 41 of 46
Where applicable a continuous record of the Inert gas operations must be maintained
3.9.2. Commencement and Progress of Discharge
When deepwell (such as Framo and Kosaka) cargo pumps are used in parallel to discharge into a
common discharge line, it is essential that the discharge pressures of all pumps in the group are
balanced to prevent backflow of cargo causing overflow of one or more tanks in the group. All
tanks should be closely monitored during this time.
Commencement of Discharge
The following procedure is common to all types of deep well pump and must always be followed when
commencing discharge. Where the procedure refers to a specific hydraulic system pressure, users of
electric pumps should use the equivalent power consumption figure determined from the manufacturer’s
operating instructions or from experience.
1. The number of full (98% capacity) tanks to be commenced as a group must not exceed two.
2. Ensure that cargo tanks, which are not part of the group to be initially discharged are isolated from the
group.
3. Start the pumps in pairs at a minimum 100 bar hydraulic pressure and open the pump discharge
valves. At this pressure the pump will run smoothly but produce minimal cargo backpressure.
4. When all pumps are running at 100 bar hydraulic pressure, check the ullage levels in all tanks in the
group and the cargo back pressure at the pump gauges and/or the manifold.
5. When satisfied that the situation is stable, increase the hydraulic pressure to each pair of pumps in
turn in increments of 10-20 bar until all pumps in the group are running at the same hydraulic pressure
and the required cargo backpressure at the manifold has been achieved.
6. To add additional pumps to the group at a later stage in the discharge operation, reduce the hydraulic
pressure of the pumps already running to 100 bar. Open the isolator valves of the additional pumps and
start them at the same pressure, then open their discharge valves.
7. Bring the Level of all cargo tanks with the same cargo to be discharged to below 90%.
Chief Officer or in his absence the Master should be present in the control room during initial stages of
discharge.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 42 of 46
PROGRESS OF DISCHARGE
1. Progress of the discharge must be closely monitored.
2. Tanks are to be discharged as quickly as possible to achieve back pressure as agreed between vessel
and shore in writing, which should not be exceeded.
3. The estimated time of completion must be calculated basis the rate of discharge. Terminal, surveyor
must be given notice of completion as required.
4. Tank levels must be monitored continuously to prevent dry running of pumps.
5. Stripping of tanks must be carried out in accordance with the P&A Manual to minimize the contents
remaining in the tank.
6. For certain cargoes, the discharge is maximized by squeezing the bottom of the tanks into the pump
stacks. “Refer to section 3.11 for squeezing procedures”.
7. High viscosity and solidifying cargo require special handling precautions to ensure entire cargo is
effectively discharged. These precautions may include staggering ballast operation, recirculation cargoes,
heating of cargoes etc. It is essential that the ship’s officer have planned well in advance depending on
the nature of the cargo.
Chief Officer should be present during critical operations such as sampling, connection / disconnection,
stripping and line blowing. If Chief Officer is unable to be present due to rest hours or other requirements,
Master shall be present in lieu.
3.9.3. Preventing Cargo Contamination while Discharging
The following precautions can help prevent inadvertent contamination of cargo during discharging:
1. Maintain a minimum of two valves separation throughout the discharge of multiple grade oil products.
Chemicals must be maintained under positive segregation.
2. While handling multi-grade cargoes, upon completion of each grade, valves should be sealed and the
seals pointed out to the inspector and logged. CCR hydraulic valve knobs must be isolated. If possible,
leave seals in place until discharge is completed and ask the inspector to note the fact.
3. The most sensitive grade should be discharged first, if possible.
A watch officer discovering contamination should:
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 43 of 46
1. Stop discharging the relevant cargo.
2. Close that system’s valves.
3. Advise the chief officer, who advises the master and who contacts the owner and his local P&I
correspondent.
4. The master should:
a. Sample the remaining cargo and request testing.
b. Await instructions from the owner.
c. Never try to conceal a handling error, which may have resulted in contamination. The sooner
problems are identified, the less the owner’s potential exposure.
3.9.4. Tank Inspection after Discharge
Upon completion of discharge the cargo tanks will be inspected by receiver’s representative or surveyor
accompanied by the chief officer to determine whether the tanks have been properly drained. Once
satisfied a dry tank certificate will be issued.
However if the cargo tank has significant quantities of un-pumpable cargo remaining on board then a
reasonable estimate of this quantity must be made along with the owners P&I and surveyor. Ship’s officer
must note that this situation should be avoided at all cost as the cargo remaining on board is considered
short delivery and owners of the vessel become liable for the cost of the cargo. Office and operators must
be immediately informed and vessel must not sail or sign the documents without approval.
For Annex 2 cargoes in case vessel is not able to comply with minimum stripping quantity requirement as
per P&A manual due to pump failure or stripping failure, a prewash must be carried out in the unloading
port.
3.9.5. Cargo Residue and Outturn
Draining and Stripping
1. Ensure that the maximum amount of cargo is delivered and “in transit” losses are minimized.
2. On completion of discharge all lines and tanks are to be stripped as dry as possible to comply with
Stripping requirements laid down in the vessel’s P&A Manual. Do not blow back lines into cargo tanks.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 44 of 46
3. The pump discharge line is cleared by purging the pump and discharge line with inert gas in the form of
nitrogen.
4. Air may be used with certain cargoes of a non volatile nature and which are not static accumulator
cargoes. This procedure is described in the pump instruction manual.
5. The cargo hoses and cargo lines including common line are to be drained as much as possible, as
soon as a cargo operation has been completed, especially if the cargo has a high freezing point or is of
polymerizing nature.
6. Make sure that the cargo residues in the hose connection between ship and shore are not blown back
into the ship’s cargo lines.
7. In the case of heated cargoes, maintaining the cargo temperature properly assists draining.
3.10. CARGO RESIDUES AND TANK WASHINGS MUST BE DISPOSED AS PER THE
REQUIREMENTS OF MARPOL ANNEX II AND VESSEL'S P&A MANUAL.FAILURE OF CARGO
PUMP
1. Portable Cargo Pump must always be kept ready for use in case the regular submersible pump fails.
2. If the portable pump must be used, P&A manual must be consulted for proper discharge procedure.
The Check List for use of Portable Pump (OP-CHEM-40) is to be used and complied with.
3. Discharging flammable or toxic cargoes will require sluice or alternative arrangement fitted to the
portable pump. Risk Assessment and Office approval is also required in such case.
4. Use of Portable cargo pump for discharging cargo is only permitted after Risk Assessment and express
permission from all concerned parties such as, Terminal, Cargo Owners / Charterers and Office.
5. In case vessel is not able to comply with minimum stripping quantity requirement as per P&A manual
due to pump failure or stripping failure, a prewash must be carried out in the unloading port.
3.11. SQUEEZING OF CARGO TANKS
For cargo tanks being discharged and stripped of vegetable and animal oils or fats it is usually required
that personnel be sent into the cargo tank in order to sweep the final traces into the pump suction. This
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 45 of 46
operation is “HIGH RISK” owing to the entry being made in atmospheres which could be extremely
hazardous.
The significant hazards that could be identified during such an entry are:
1. The presence of toxic gases such as Carbon Monoxide which could prove fatal when inhaled or
absorbed through the skin.
2. Asphyxia caused owning to the lack of oxygen leading to suffocation.
3. Anaesthesia by certain vapours which lead to loss of consciousness due to their effect on the nervous
system.
4. Skin / chemical burns caused by hot and corrosive cargo (e.g. cashew oil).
Prior to arrival at discharge port, a sweeping plan is to made by the Chief Officer taking into account
amongst other factors, local and terminal requirements towards tank entry, the number of tanks to sweep,
watch routines of personnel available, where possible execution of the sweeping within daylight hours,
method of ensuring continuous ventilation, methods for ensuring continuous vapour detection during
sweeping, level at which the heating of each individual tank to be swept is to be stopped, rescue
procedures, means, signals and actions in the event of an emergency, etc.
Refer to and comply with “Cargo Tank Squeezing Permit (OP-CHEM-10)” for squeezing precautions.
Management of Shore contractor for Squeezing operations
Whenever contractors or work gangs are employed for squeezing operations, the master shall ensure
their understanding and compliance with all relevant safe working practices.
The Contractor should take part in the vessels safety/tool box meetings to discuss the arrangements for
work . During the toolbox meeting he shall be familiarized on the company squeezing procedures as
outlined in chemical tanker manual chapter 3.
Wherever applicable, he should sign the formal approval relevant to work being undertaken by his
workforce. Prior entering the cargo tank and carrying out the squeezing operation the contractor shall sign
the squeezing permit to confirm compliance with the company procedures. Contractors should be
effectively supervised and controlled by a Responsible Officer.
Uncontrolled when Printed
CHEMICAL TANKER MANUAL
CH. 03 CARGO HANDLING AND TRANSFER Rev. No. 1
Date 15-Apr-16
Page Page 46 of 46
3.12. CARGO RECORD BOOK
Vessels carrying noxious liquid substances in bulk shall be provided with a Cargo Record Book to record
relevant cargo / ballast operations. When making entries of the Cargo record Book, the date, operational
code and item number shall be inserted in the appropriate columns and the required particulars shall be
chronologically recorded in the blank spaces.
Each completed operation shall be signed for and dated by the chief officer and, if applicable, by a
surveyor authorized by the competent authority of the state in which vessel is unloading. Master shall
countersign each completed page.
Entries of the Cargo Record Book are required only for operations involving categories X, Y, Z and Other
Substances (OS). The Cargo Record Book shall be kept in such a place as to be readily available for
inspection and it shall be retained for a period of three years after the last entry has been made.
Uncontrolled when Printed