Chapter 10 Mass relationships in chemical reactions: Stoichiometry.
Chapter 4 Chemical Reactions and Solution Stoichiometry.
-
Upload
montana-maris -
Category
Documents
-
view
252 -
download
2
Transcript of Chapter 4 Chemical Reactions and Solution Stoichiometry.
![Page 1: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/1.jpg)
Chapter 4
Chemical Reactions and Solution Stoichiometry
![Page 2: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/2.jpg)
Water: The Common Solvent
• Essential for most biological reactions
• Polar covalent molecule• Partial charges create
poles (dipole moments)• Polarity gives water the
ability to dissolve compounds
![Page 3: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/3.jpg)
WaterHydration of a Solute
Hydration-the interaction between solute particles and water molecules
![Page 4: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/4.jpg)
WaterHydration of a Solute
• When ions dissolve, they break up into individual ions
• NH4NO3(s) NH4+
(aq) + NO3-
(aq)
• HOWEVER, solubility varies greatly among ionic compounds– Solubility depends on relative
attractions of ions for each other (to be covered in CHpt 11)
• Take home message:– An ionic solid dissolves into dispersed
ions in water upon hydration
![Page 5: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/5.jpg)
Non-ionic solubility• Non ionic compounds can
be soluble if they have a polar bond.
• Examples: – ethanol C2H5OH
– Methanol CH3OH
– Acetone (CH3)2CO
• Rule of Thumb– Polar molecules are
soluble, “like dissolves like”
![Page 6: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/6.jpg)
Non soluble Compounds/ions
• Carbonate (CO32- )
• Phosphate (PO43- )
• ETC………………………………………………………………………………………………………………………………………………
• Non-polar molecules (animal fat)
![Page 7: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/7.jpg)
Characterization of Solutions• Electrical Conductivity– Strong electrolytes: dissolve and completely ionize
in water• Strong conductors of electricity• Soluble Salts, Strong Acids, Strong Bases
– Weak electrolytes: small degree of ionization• Weak conductors of electricity (but STILL CONDUCT!!)• Weak acids (Acetic Acid), weak bases (NH3)
– Non-electrolytes: dissolve but no ionization• Ie; Sucrose (C12H22O11), Ethanol (C2H5OH)
![Page 8: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/8.jpg)
Composition of Solutions
• Molarity= • What is the molarity of a 0.30 liter solution containing 0.50 moles of NaCl?
• How many liters of solution are needed to make a 1.66 M solution containing 2.11 moles of KMnO4?
Moles of soluteliters of solution
![Page 9: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/9.jpg)
Composition of Solutions
• What is the molarity in 650. ml of solution containing 63 grams of NaCl?
• How many grams of Ca(OH)2 are needed to produce 500. ml of 1.66 M Ca(OH)2 solution?
• What volume of a 0.88 M solution can be made using 130. grams of FeCl2?
![Page 10: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/10.jpg)
Composition of Solutions
• Dilutions• Moles solute before = moles after
M1V1=M2V2
• How do you prepare a 250.-ml of a 2.35 M HF dilution from a 15.0 M stock solution?
• If 65.5 ml of HCl stock solution is used to make 450.-ml of a 0.675 M HCl dilution, what is the molarity of the stock solution?
![Page 11: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/11.jpg)
Tonight’s Homework
• Worksheet I just handed you • Pg 180-#’s 15,16,21-25• Read Chapter 4, Sections 1-5 (20 pgs)– DO IT OR YOU WILL BE BEHIND TOMORROW!!!!
![Page 12: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/12.jpg)
Types of Solutions
• Precipitation Reactions- aqueous solutions form an insoluble precipitate (duh…)– Involves using solubility rules (pg 150 Table 4.1) to
determine the solid precipitate.
FOR EXAMPLEPb(NO3)2(aq) + KCl(aq)
![Page 13: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/13.jpg)
Pb(NO3)2(aq) + KCl(aq)
• We know that:– Most nitrates salts are soluble. – Most Group I salts are soluble. – Most Chloride salts are soluble with the exception
of Pb+2 and others. – Therefore, we determine the products to be:
Pb(NO3)2(aq) + KCl(aq) PbCl2(s) + KNO3(aq)
![Page 14: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/14.jpg)
Describing reactions/Writing equations
• Molecular Equation:• Pb(NO3)2(aq) + 2KCl(aq) PbCl2(s) + 2KNO3(aq)
• Complete ionic Equation• Pb+
(aq) + 2NO3-(aq) + 2K+
(aq) + 2Cl-(aq) Pb+2
(s) + 2Cl-(s) + 2K+
(aq) + 2NO3-(aq)
• Net Ionic Equation (get rid of the spectator ions)– Spectator ions: present in the aqueous solution before and after
reaction. In this case, K+and NO3-
– Indicate ions that form precipitate.
Pb+(aq) + 2Cl-
(aq) PbCl2(s)
![Page 15: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/15.jpg)
Solution Stoichiometry
• Steps to solving Solution Stoichiometry– 1. Identify Species, determine reaction– 2. Write balanced net ionic equation– 3. Calculate moles of reactants– 4. Determine limiting reactant– 5. Calculate moles of product– 6. Convert to proper unit, sig figs, etc…
![Page 16: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/16.jpg)
Calculate the mass of solid NaCl that must be added to 1.5L of a .100M AgNO3 solution to precipitate all the Ag+ ions in the form
of AgCl
• Step 1: NaCl(s) + AgNO3(aq) AgCl(s) + NaNO3(aq)
• Step 2: Ag+(aq) + Cl-
(aq) AgCl(s)
• Step 3: 1.5L x .1M Ag+ = ?• Step 4?• Step 5?• Step 6?
![Page 17: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/17.jpg)
Calculate the mass of solid NaCl that must be added to 1.5L of a .100M AgNO3 solution to precipitate all the Ag+ ions in the form
of AgCl
1Ag+(aq) + 1Cl-
(aq) 1AgCl(s)
• Step 3: Using a 1:1 mole ratio from the balanced equation
• 1.5L x .1M Ag+ = .150 mol Ag+
• .150 mol NaCl x (58.45g NaCl/1mol)= 8.77g NaCl• Step 4?• Step 5?• Step 6?
![Page 18: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/18.jpg)
More homework
• Pg 181 #’s 29-36, 39-44
![Page 19: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/19.jpg)
Acid-Base Reactions
• Acids-produce H+ ions when dissolved in water. A proton donor.
• Bases-produce OH- ions when dissolved in water. A proton acceptor
H+(aq) + OH-
(aq) H20(l)
![Page 20: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/20.jpg)
Solution Stoichiometry for Acid-Base Reactions
• Steps to solving Solution Stoichiometry– 1. Identify Species, determine reaction– 2. Write balanced net ionic equation– 3. Calculate moles of reactants– 4. Determine limiting reactant– 5. Calculate moles of product– 6. Convert to proper unit, sig figs, etc…
![Page 21: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/21.jpg)
Solution Stoichiometry for Acid-Base Reactions
FOR EXAMPLE What Volume of a .100M HCl solution is needed to
neutralize 25.0 mL of .350M NaOH?In reality, all you are trying to do is match the moles of
hydroxide ions with moles of hydrogen ions. • 1. Identify Species, determine reaction• 2. Write balanced net ionic equation• Involves using solubility rules (pg 150 Table 4.1) to
determine a solid precipitate and spectator ions
![Page 22: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/22.jpg)
What Volume of a .100M HCl solution is needed to neutralize 25.0 mL of .350M NaOH?
• 1. Identify Species, determine reaction, mole ratio
HCl(aq) + NaOH(aq) NaCl(s) + H20(l)
– Mole ratio of 1:1:1:1– Remember your solubility rules, – Remember that you cannot dissolve water in
water, so water is always in the “liquid” state of matter. (Sounds stupid but you would be surprised).
![Page 23: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/23.jpg)
What Volume of a .100M HCl solution is needed to neutralize 25.0 mL of .350M NaOH?
• 2. Write balanced net ionic equation• Involves using solubility rules (pg 150 Table 4.1) to
determine spectator ions.– Complete ionic equation:
H+(aq) + Cl-
(aq) + Na+ (aq) + OH-
(aq) H2O(l) + Na+(aq) + Cl-
(aq)
– Na+ and Cl- are soluble, so they exist as ions in solution. Therefore, the actual reaction does not take place. They are spectator ions.
• H+(aq) + OH-
(aq) H2O(l)
![Page 24: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/24.jpg)
What Volume of a .100M HCl solution is needed to neutralize 25.0 mL of .350M NaOH?
• 3. Calculate moles of reactants (don’t forget your mole ratios in this step!)– M = n / V– .350M HCL = n / 0.025L– n= .00875 moles account for sig figs 8.75 x 10-3
moles (preferred by AP graders)
![Page 25: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/25.jpg)
• 4. Determine limiting reactant– We are adding a reactant, therefore we do not
care about a limiting reactant. But in reality it is a 1:1 mole ratio so there isn’t one.
What Volume of a .100M HCl solution is needed to neutralize 25.0 mL of .350M NaOH?
![Page 26: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/26.jpg)
What Volume of a .100M HCl solution is needed to neutralize 25.0 mL of .350M NaOH?
• 5. Calculate moles of reactant needed (HCl solution)• We have a 1:1 mole ratio of hydrogen ions to hydroxide
ions. • Moles H+ = Moles OH- in order to reach neutralization
point
• Therefore, we need 8.75 x 10-3 mol H+ (present in HCl)
![Page 27: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/27.jpg)
What Volume of a .100M HCl solution is needed to neutralize 25.0 mL of .350M NaOH?
• 6. Convert to proper unit, sig figs, etc…– The question asks us for the volume of .1M HCl– So:
M = n / V V = n / MVHCl= 8.75 x 10-3 mol H+
.100 mol H+ / L
VHCl= 8.75 x 10-2
![Page 28: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/28.jpg)
More homework…
• Pg 182 #’s 45-50
![Page 29: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/29.jpg)
Acid-Base titrations
• Key vocabulary– Volumetric Analysis-technique for determining the amount of
substance through titration– Titration-delivery of a measured volume of a known solution
into a substance of unknown concentration• Titrant• Analyte
– Equivalence point-the point at which enough titrant has been added to react exactly with the analyte
– Indicator-a substance that changes color at or near the equivalence point
– Endpoint-point actual point where the indicator changes color
![Page 30: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/30.jpg)
Acid-Base titrations
• Requirements for sucessful titrations– 1. exact reaction between titrant and analyte must
be known– 2. Equivalence point must be marked accurately
(.15 mL of titrant added, etc…)– 3. Volume of titrant required to reach equivalence
point must be known accurately (to calculate percent error)
![Page 31: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/31.jpg)
Acid-Base Titrations
• Basically, a titration is a neutralization reaction, so we follow the same rules as before. – The goal is to react an equal hydrogen ions to
react with hydroxide ions.
![Page 32: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/32.jpg)
Acid-Base Titrations
For Example:A student dissolves 1.3009g KHC8H4O4 (KHP) in
distilled H20, adds Phenolphthaleine as an indicator, and titrates with NaOH. It was found that 41.20mL of NaOH is required to react with the 1.3009g KHP. What is the concentration of the sodium hydroxide?
![Page 33: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/33.jpg)
A student dissolves 1.3009g KHC8H4O4 (KHP) in distilled H20, adds Phenolphthaleine as an indicator, and titrates with NaOH. It was found that
41.20mL of NaOH is required to react with the 1.3009g KHP. What is the concentration of the sodium hydroxide?
– 1. Identify Species, determine reaction, mole ratios• KHC8H4O4(aq) + NaOH(aq)
KOH + NaHC8H4O4(aq)
– 2. Write balanced net ionic equation• K+ + HC8H4O4
-(aq) + Na+ + OH-
(aq)
K+ + OH- + NaHC8H4O4(aq)
![Page 34: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/34.jpg)
Oxidation-Reduction Reactions
• Redox reaction-one or more electrons are transferred
• Oxidation state (number)-the imaginary charges the atoms would have if the shared electrons were divided equally between identical atoms bonded to each other (huh?)
![Page 35: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/35.jpg)
Rules for assigning Oxidation States
• Pg 167, Table 4.2 of your textbook
• Memorize it…• More importantly,
memorize exceptions to the norm
![Page 36: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/36.jpg)
Oxidation number Practice
• Assign Oxidation states to all atoms in the following– CO2
– SF6
– NO3-
– CH3-
– H2O2
– H2O
– START WITH FIRST DRAWING THE MOLECULE, oxidation states do not have to be whole numbers (for some atoms)
– KMnO4
– NiO2
– K4Fe(CN)6
– N2H4
– FeO4
– Na2C2O4
![Page 37: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/37.jpg)
Oxidation-Reduction Reactions
• Oxidation-increase in oxidation state (loss of electron). Ie, going from -1 to +1
• Reduction- decrease in oxidation state (gain of an electron). Ie, going from +1 to -1
• Oxidizing agent-the electron acceptor• Reducing agent-electron donor
![Page 38: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/38.jpg)
Identification of Oxidizers, reducers
• 2Al (s) + 3I2 2AlI3
– Step 1: balance equation, assign oxidation states to reactants
– Step 2: assign oxidation states to products
– Step 3: Identify who gained electrons (reducing agent
– Step 4: Identify who lost electrons (oxidizing agent)
This was an easy problem
![Page 39: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/39.jpg)
Identification of Oxidizers, reducers
• Identify the oxidizing and reducing agents– PbO(s) + CO2(g) Pb(s) + CO2(g)
– CH4(g) + O2(g) CO2(g) + H2O(l)
– Cr2O72-
(aq) + HCl ZnCl2(aq) + H2(g)
![Page 40: Chapter 4 Chemical Reactions and Solution Stoichiometry.](https://reader035.fdocuments.net/reader035/viewer/2022081420/56649caf5503460f9497377f/html5/thumbnails/40.jpg)
Homework
• Pg 182-183, #s 57-62