CGS2 kit installation procedure on Ducati motorbikes ... CGS2 DUCATI_EN.pdf · 1) Remove body...
Transcript of CGS2 kit installation procedure on Ducati motorbikes ... CGS2 DUCATI_EN.pdf · 1) Remove body...
CGS2 kit installation procedure on Ducati
motorbikes models
748 – 749 – 999 – 1098 – 848 – 1198 - Streetfighter
SP elec tron ics
w w w . s p e l e c t r o n i c s . i t R 2 0 1 0 0 4 2 1
1) Remove body panels uppers and lowers
A
B
C
SP elec tron ics
( CGS2 kit installation procedure on Ducati motorbikes models 748 – 749 – 999 – 1098 – 848 – 1198 Streetfighter )
2) Place the CGS2 eBox near Dashboard. We recommend to arrange all wiring on the right side (Gear indicator display is optional)
- Gear indicator display
- CGS2 eBox
- CGS2 main wiring
- CGS2 accessory wiring (*)
*NOTE: keep this wiring away from dashboard's connector!
SP elec tron ics
( CGS2 kit installation procedure on Ducati motorbikes models 748 – 749 – 999 – 1098 – 848 – 1198 Streetfighter )
FEED
SPEED
CW
SP elec tron ics
( CGS2 kit installation procedure on Ducati motorbikes models 748 – 749 – 999 – 1098 – 848 – 1198 Streetfighter )
Arrange the Plug&Play wiring under Airbox and between the two strokes for right to left crossing
eBox
3) Connect the Plug&Play CGS2 wiring:
RPM
CSS sMec
SP elec tron ics
( CGS2 kit installation procedure on Ducati motorbikes models 748 – 749 – 999 – 1098 – 848 – 1198 Streetfighter )
sMec
Arrange the Plug&Play wiring under Airbox and between the two strokes for right to left crossing
sMec
SP elec tron ics
( CGS2 kit installation procedure on Ducati motorbikes models 748 – 749 – 999 – 1098 – 848 – 1198 Streetfighter)
4) Connect the CGS2 sensor (sMec label)
- Sensor wiring
- Ducati lever sensor
SP elec tron ics
( CGS2 kit installation procedure on Ducati motorbikes models 748 – 749 – 999 – 1098 – 848 – 1198 Streetfighter)
NOTICE: please take attention on side stand connection of your motorbike. A few Ducati models may
have differents electricals set-up on side stand connector. This may cause malfunctions of quick-
shifter. In order to complete installation, check the CGS2 connectors on side stand (CSS label) and
verify that singles pins of connectors matches right. Please see a drawing following for an example.
In case of wires position mismatch on connectors, you can reposition them.
1
1
2
2
3
3
4
4
D D
C C
B B
A A
Titolo:
Data emissione:
File:
Pag.:
/
Codice prodotto:Via Astichello, 25
36030 Montecchio Prec.no (VI)Phone 0445-334677Fax 0445-339595
Revisione:
Disegno di nostra proprietà, divulgazione e riproduzione totale o parziale vietate ai sensi di
legge.
SP electronics APPLICAZIONE CGS2 DUCATI
29/09/2010
CGS2 CSS DUCATI CON CTM.SchDoc
1 11.0
PICK-UP SENSORPICK-UP MOTORE
SPEED SENSORSENS.VELOCITA'
CGS2CGS2
GEAR INDICATOR DISPLAYDISPLAY CONTAMARCEsM
ec
Switch CGSSensore CGS
DY
SIDE-STAND BYPASSConnettore esclusione cavalletto Ducati
THE ORIGINAL SIDE-STAND SENSOR FUNCTION IS PRESERVED
LA FUNZIONALITA' ORIGINALE DEL SENSORE E' PRESERVATA
FUEL PUMP
POMPA BENZINA
FUEL PUMP RELAYRELE' POMPA BENZINA
DY
TO ENGINE ECUALLA CENTRALINA MOTORE
CW
APPLICAZIONE DEL KIT CGS2 TAGLIO CAVALLETTOCGS2 APPLICATION ON THE SIDE-STAND SENSOR
-Disponibile l'opzione con sensore su leva diretta per Ducati-If required the sensor switch isavailaible on Ducati direct lever.
For support contact us by
Phone ( from 2 pm to 5 pm) : +39 (0)445 334 677
or
Email : [email protected]
w w w . s p e l e c t r o n i c s . i t
SP elec tron ics