WEG Cfw 08 a Frequency Inverter Manual 0899.5242 Manual English
CFW-11 - BSC PDFs/WEG... CFW-11 3 Technology - Patents Vectrue Technology® WEG VARIABLE SPEED DRIVE...
Transcript of CFW-11 - BSC PDFs/WEG... CFW-11 3 Technology - Patents Vectrue Technology® WEG VARIABLE SPEED DRIVE...
Motors | Automation | Energy | Transmission & Distribution | Coatings
CFW-11 Variable Speed Drives
www.weg.net
CFW-112
Innovative and simple The CFW-11 presents many innovations that are helpful and benefi cial to customers, mainly due to the simplicity of its installation and operation. The CFW-11 was developed based on Plug-and-Play philosophy (connect and use) allowing simple and fast installation of the VSD and its accessories. The Keypad has a navigation and programming system similar to mobile phones, with soft-key buttons. It is possible to access the parameters sequentially or through groups of parameters. The Keypad also makes the Oriented Start-up function available, guiding the user through the necessary programming.
FlexibilityThe CFW-11 adapts itself to the customer’s needs through a broad range of accessories, which are easily installed. Besides this, the standard product comes with the SoftPLC function that attributes PLC functions to the VSD, which allows the customer to create his/her own applications (user programs) through the WLP software (programming in LADDER).
CFW-11
The CFW-11 is a variable speed drive series with state of the art technology for three-phase induction motors. It can be used in a wide range of applications, since it is designed for running on either Normal or Heavy Duty loads. Its performance is excellent, providing increased productivity and an improvement in the quality of the process in which it is used.
1.1 to 2.2kW - 1.5 to 3HP200-240V - Single-phase
1.1 to 55kW - 1.5 to 75HP 200-240V - Three-phase
1.5 to 370kW - 2 to 600HP380-480V - Three-phase
New Frame Sizes F & G
new
www.weg.net
CFW-11 3
Technology - Patents
Vectrue Technology®
WEG VARIABLE SPEED DRIVE CONTROL TECHNOLOGYg Linear and adjustable V/f, VVW (Voltage Vector WEG) and
vector controls are available in the same product.g Two types of vector control: Sensorless and closed loop Vector contro (Encoder Interface required).g Sensorless vector control permits high torque and quick response in open loop, even at low speeds.g The self-tunning function automatically matches the vector control or VVW to the motor and load used.g Through the adjustable V/f control, it is possible, for example, to adjust a quadratic V/f curve, providing energy savings for quadratic torque loads (e.g.: centrifuge pumps and fans).
Optimal Braking®
In applications where inertia is a relevant point and short deceleration times is required, great amount of energy is returned from the motor to the VSD. To handle this energy, traditional VSDs have to dissipate it as heat in power resistors. Such resistors are usually heavy and some instalation criterias must be considered due to their heat dissipation. As an option to the use of braking resistors, CFW-11 features a special braking method in vector control mode known as “ Optimal Braking®. This innovation delivers to the load a high performance braking torque without requiring a braking resistor.The following graph shows the advantages of using Optimal Braking® compared to other methods, thus ensuring an ideal, optimized and low cost solution for braking applications.
Typical Braking Torque x Speed Graph for a 10 HP / 7.5 kW motor driven by a CFW-11
Dynamic Braking Torque CurveOptimal Braking® Torque CurveDC Braking Torque Curve
Braking Torque (%)
100 (%)
TB1
00 20% 100% 200%
Optimal Flux ®
TECHNOLOGY FOR MOTORS DRIVEN BY VSDs IN APPLICATIONS WITH CONSTANT TORQUE LOADSg Rated torque at low speeds eliminating the need for independent
ventilation or motor oversizing.g Space saving and cost reduction of the application. g Improved performance of the package VSD and motor (an exclusive WEG solution).
High effi ciency WEG motor + CFW-11Solution applied only to CFW-11 with high effi ciency WEG motors.
Wmagnet Drive System®
Frequency inverter system with permanent magnet motors (Wmagnet), the motor with the highest effi ciencyin the market with the CFW11 inverter.It is perfect for applications where speed variation, low noise level and reduced size are required. In sensorless control theWmagnet Drive System® is able to do torque control with zerospeed and it can run motor in very low speed without theneed of forced ventilation.
www.weg.net
CFW-114
Applications
Multi-Pump ControlThe CFW-11 features the Multipump Control, which permits the CFW-11 to control up to 5 pumps in order to maintain the pipeline pressure constant regardless of the outflow fluctuations. In this system, an intelligent control of the pumps is done by the VSD, which decides the moment to start or stop each of the pumps based on the outflow demand. Besides that, the VSD also monitors the suction pressure and the tank level.The CFW-11 also alternates the pumps according to their using time, thus ensuring an uniform wear and tear of motors and pumps.Two types of Multipump Control are available: fixed and floating controls. In fixed control, the VSD is able to control one of the pumps at variable speed and to start and stop other 4 pumps at fixed speed. In floating control, the VSD is able to control up to 4 pumps, all of them at variable speed.The Multipump Control for CFW-11 is available as an applicative software for SoftPLC function (see page 17) and can be downloaded from www.weg.net
The CFW-11 can be used in both simple and sophisticated applications, due to its broad range of functions and easy configuration, installation and operation. The CFW-11, through its Vectrue Inverter technology, presents excellent static and dynamic performance, precise torque and speed control, dynamic response, positioning precision, and high overload capacity. The CFW-11 was also developed for applications where the decisive factor is safety, through several built-in protections and alarms as well as through the safety stop function in accordance with EN 954-1, category III.
Pumps and fans g Precise control of process variables (pressure, flow, temperature, etc.) through a PID regulator superposed to the speed control.g Optimization of power consumption through speed control with an adjustable V/f curve.g Possibility of safety and maintenance signaling and alarms of pumps and fans.g Availability of PID regulators to control other process accessories like valves, dumpers, other VSDs, etc.
Compressorsg Optimization of system pressurization control with energy savings and improvement of compressor efficiency.g Reduction of motor startup current minimizing the wear and tear of the mechanical system permitting a reduction of contracted demand.g Possibility of safety and maintenance signaling and alarms of pressurization system.g Provides startup system control of other compressor units with an increased efficiency of the pressurization system.
www.weg.net
CFW-11 5
Applications
Paper and Cellulose / Wood g Three monitoring parameters displayed at once on the HIM g USB communication port at the front of the VSD for data monitoring and parameters configuration via software Superdrive.g Highly precise speed and torque control.g Flexible hardware programming and confguration, making easier applications where syncronism is demanded.g Possibility to be integratet in a variety of communication protocols mainly used in the industry. g Provided in a compact design the CFW11 Series allows the assembly directly next to one another with no reduction of ambient temperature. g Quick and simplified programming.g Highly reliable and robust.g For large power ratings modular topology can be used( CFW-11M).
Chemical and Petrochemicalg Highly reliable and robust.g Provided in a compact design the CFW11 Series allows the assembly directly next to one another with no reduction of ambient temperature.g Plug-and-play system for additional modules, ensuring elevated flexibility in adapting to existing systems.g Possibility to be integrated in a variety of communication protocols mainly used in the industry.
Ironworks and Metallurgy g Highly precise speed and torque control.g Large overload capacity (models sized in HD).g Flexible hardware programming and configuration.g Possibility to be integrated in a variety of communication protocols mainly used in the industry.g Provided in a compact design the CFW11 Series allows the assembly directly next to one another with no reduction of ambient temperature.g For large power ratings modular topology is used( CFW-11M)
Cement and Mining g Robust and large overload capacity(models sized in HD).g Provided in a compact design the CFW11 Series allows the assembly directly next to one another with no reduction of ambient temperature. g Possibility to be integrated in a variety of communication protocols mainly used in the industry. g Quick and simplified programming.g Highly reliable and robust.g For large power ratings modular topology is used( CFW-11M)
www.weg.net
CFW-116
Applications
OverHead Crane / Lifting g SoftPLC function.g Three modes of vector control.g Highly compact.g Intelligent control of ventilation system.
Coolingg SoftPLC function built in the standard product enabling the use of two controllers simultaneously. This characteristic is for HVAC applications.g Three monitoring parameters displayed at once on the HIM g USB communication port at the front of the VSD for data monitoring and parameters configuration via software Superdrive.
Process Machinesg Built-in PLC and Real Time Clock.g High connectivity.g Fieldbus.g Highly precise speed and torque in all speed ranges.g User friendly interface and programming.
Sugar and Alcohol g Modular and compact.g 12-pulse rectifier for reduction of harmonic content.g Regenerative rectifier for centrifuges.g Highly robust and reliable.
www.weg.net
CFW-11 7
Keypad
The CFW-11 keypad was developed for simple and fast interaction while providing excellent visibility for the user.
Easy to use Interface Tools:g Graphic display.g Soft-keys for easy operation.g Backlight.g Real time clock.g Copy function.g Plug-in (connection with CFW-11 turned on).g Language selection.g Remote Keypad.
Left soft-key: function defi ned by the display
Right soft-key: function defi ned by the display
Key for scrolling through menus and parameters and for modifying
parameter content
FWD/REV Selection
Local / Remote Selection
JOG key
Start key
Stop key
Remote KeypadThe Keypad can be installed on panel doors or machine consoles with a protection degree of IP56.
www.weg.net
CFW-118
NU
MER
IC V
ALU
ES
Monitoring Modes
The keypad can be configured to display reading parameters in three different modes.
Oriented Start-upFor simlpified Start-up, CFW-11 guides the user through the necessary programming to adjust the VSD to the motor and power supply.
Fault History GroupIt shows the parameters with the last 10 faults and the day, month, year and time when they occured.
Read Only Parameters GroupIt shows reading parameters only.
Basic ApplicationThe Basic Application Group contains the basic parameters, which need to be adjusted in most applications. The CFW-11 guides the user through these parameters.
Backup Parameters GroupThe Backup Parameters Group allows CFW-11 parameters to be transferred to the Keypad or FLASH Memory Module (available in the standard product) and vice versa. During CFW-11 operation, the modified parameters are saved in the FLASH Memory Module regardless of user command.
Selectable LanguageThe user can choose the Keypad language: Portuguese, English, Spanish, German, etc.
Changed Parameters GroupIt shows only the parameters that are programmed different from the factory default.
Functions GroupThere are several groups divided by functions, only making available only the parameters related to the function. Example: Vector Control Group, Communication Group, I/O Configuration Group, etc.
Status Indicationg Run.g Ready.g Configuration.g Self-tuningg VSD disabled by fault and the fault number.g Last alarm.
Local / Remote Indication FWD/REV Indication
Motor speed
Time indication Soft-key function
LA
RG
E C
HA
RA
CTE
RS
BA
R G
RA
PH
S
The keypad displays parameters in a hierarchy mode organized by groups.
www.weg.net
CFW-11 9
Accessories
CFW-11 was developed based on Plug-and-Play philosophy. It automatically recognizes andmanual configuration.
Slot 5 – Built-in flash Memory Module (available in the standard product)
Slot 1 – I/O Expansion (inputs and outputs)
Slot 2 – Encoder Interface
Slot 3 – Communication 1
Slot 4 – Communication 2
www.weg.net
CFW-1110
Accessories
Name Description Slot Appearance
I/O E
xpan
sion
IOA-01
2 14-bit analog inputs in voltage or current
12 digital inputs2 14-bit analog outputs in voltage or current2 open collector digital outputs
IOB-01
2 isolated 12-bit analog inputs
12 digital inputs2 isolated 11-bit analog outputs in voltage or current2 open collector digital outputs
Inte
rfac
e w
ith E
ncod
er
ENC-01
Incremental encoder module
25 to 12 Vdc100 kHzWith encoder signal repeater
ENC-02
Incremental encoder module
25 to 12 Vdc
100 kHz
Com
mun
icat
ion
RS485-01 RS-485 Serial Communication Module (Modbus-RTU) 3
RS232-01 RS-232C Serial Communication Module (Modbus-RTU)
3RS232-02
RS-232C Serial Communication Module with DIP-switches for microcontroller’s fl ash memory programming.
CAN/RS485-01 CAN/RS-485 Interface Module (CANopen, DeviceNet and Modbus) 3
CAN-01 CAN Interface Module (CANopen and DeviceNet) 3
Profi bus DP-01 Profi bus DP Interface Module 3
RS232-05 RS-232 Interface Module (passive) (Modbus-RTU) 4
RS485-05 RS-485 Interface Module (passive) (Modbus-RTU) 4
PROFDP-05 Profi bus DP Interface Module 4
DEVICENET-05 DeviceNet Interface Module 4
ETHERNET/IP-05 EtherNet/IP Interface Module 4
PLC
Func
tions PLC11-01 Module with PLC Functions (see page 14)
1,2 and 3PLC11-02 Module with PLC Functions (see page 14)
www.weg.net
CFW-11 11
Accessories
Kit for power cable shieldingCFW-11 has a kit to make easier the connection of the motor cable shield to the ground, providing a low-impedance connection for high frequencies.
Note: 1) The kit for power cable shielding is provided PCSD-01, PCSE-01 along with VSDs that have internal RFI fi lter. Example: EU CFW11 0007 T 2 O FA Z 2) In frame sizes D and E the power cable shielding kit is factory standard, even for VSDs without internal RFI fi lter; 3) NA for frame sizes F and G.
Name Description
PCSA-01 Kit for power cable shielding for frame size A
PCSB-01 Kit for power cable shielding for frame size B
PCSC-01 Kit for power cable shielding for frame size C
PCSD-01 Kit for power cable shielding for frame size D
PCSE-01 Kit for power cable shielding for frame size E
Enclosures
( X ) Standard ( - ) NA
Note: In the KN1X-01 Conduit kit (frame sizes A,B and C) power cable shielding is also provided Kits KN1F-01 and KN1G-01 are under UL certifi cation process
Safety stop in accordance with EN-954-1, category IIIWith the activation of the safety stop function, the PWM pulses of the IGBTs are disabled. Since no voltage is available in the VSD output, no torque is applied to the motor. Thus, it is ensured that the motor remains stopped providing system safety (pending certifi cation).
Standards RatingsFrame Sizes
A B C D E F & G
IECIP20 - - - X X X
IP21 X X X KIP21D-01 - -
NEMA TYPE 1 KN1A-01 KN1B-01 KN1C-01 X KN1E-01 / KN1E-02 KN1F-01 / KN1G-01
Name Description
KN1A-01 Conduit kit for frame size A
KN1B-01 Conduit kit for frame size B
KN1C-01 Conduit kit for frame size C
KIP21D-01 Conduit kit for frame size D
KN1E-01NEMA type 1 kit for frame size E models CFW110142T2,
CFW110105T4 and CFW110142T4 KN1E-02 NEMA type 1 kit for frame size E models CFW110180T4 and CFW110211T4
KN1F-01 Conduit kit for frame size F
KN1G-01 Conduit kit for frame size G
www.weg.net
CFW-1112
Accessories
Remote keypad frame – RHMIF-01Frame for Keypad installation on panel door or machine console. Degree of protection IP56.
Blank cover – HMID - 011
Blank cover to replace the standard VSD keypad when not used.
External control supply in 24 Vdc¹Used with communication networks (Profi bus DP, DeviceNet, EtherNet/IP, etc.) so that the control circuit and the interface for the communication network continue working even if the AC supply is removed.
RFI suppressor fi lter1 (for the VSD to be in accordance with EN 61800-3 and EN 55011)CFW-11 models with built-in RFI fi lter, when properly installed, meet the requirements of the electromagnetic compatibility directive – “EMC Directive 2004/108/EC”.Example: EU CFW11 0007 T 2 O FA Z For models from frame size A to D, the RFI fi lter is optional. But for models in frame size E, the RFI fi lter is included in the standard product.
1 These options must be provided already installed in the CFW-11 (please see coding on page 26).
www.weg.net
CFW-11 13
PLC Accessory - PLC11PLC11 accessory provides the CFW-11with PLC , speed reference generator and motion control functions. It comes in two options: PLC11-01 and PLC11-02 (see differences in the table below). In many applications, this accessory allows the CFW-11 to replace an external PLC, reducing this way application costs.
Features:g Motion control with trapezoidal “S” profi les (absolute and relative)g Machine initial position search (homing)g Ladder programming through WLP Software with timers, counters, coils and contactsg RS-485 serial interface with Modbus-RTU protocolg 100 confi gurable parameters available to the user via keypad or WLPg Master/Slave function (Electronic Gearbox)g CAN interface for CANopen and DeviceNet protocolsg CANopen Master, which allows CFW-11 to control up to 25 slave devicesg WLP/ WSCAN software: network confi guration and programming software in the same environment.
Accessories
Master
CANopen slave CANopen slave
Digital and analog I/O expansion
Digital and analog I/Os
Digital and analog I/Os
WLP / WSCAN Software
Example of use of PLC11-01 as CANopen network master
Technical Specifi cation
1
2
3
4
5
6
7
8WLP / WSCAN Software
Master
Input and Outputs PLC11-01 PLC11-02Digital inputs 9 bidirectional isolated inputs: 24Vdc 4 bidirectional isolated inputs: 24VdcDigital outputs 3 bidirectional isolated open-collector outputs: 24Vdc, 500mA 3 bidirectional isolated open-collector outputs: 24Vdc, 500mARelay outputs 3 outputs NO contacts: 250Vac, 3A 1 output NO contact: 250Vac, 3AEnconder inputs 2 incremental enconder inputs: 5...12Vdc, 500mA, internal 2 incremental encoder inputs: 5...12Vdc, 500mA, internalRS-485 serial interface 1 port for Modbus-RTU protocol 1 port for Modbus-RTU protocolCAN interface 1 port for CANopen and DeviceNet protocols 1 port for CANopen and Devicenet ptotocolsAnalog inputs 1 differential input: -10...+10Vdc / 0...20mA, 14 bits -Analog outputs 2 outputs: -10...+10Vdc/ 0...20mA, 12 bits -
www.weg.net
CFW-1114
CFW-11 IP54 Drive
CFW-11 Multipump Control Function
The CFW-11 IP54 features an IP54 enclosure that protects the drive from splashingwater, corrosion and dust.The improved cooling fans on the CFW-11 IP54 ensure perfect functionality when operating at maximum loading capacity. The drive is designed to be mounted directly without the need for a customenclosure in severe environments such as:g Chemical Industryg Petrochemical Industryg Food IndustryCommunication Protocol such as Profibus, Devicenet, CAN open, Modbus-RTU,Ethernet IP can be added using optional cards.
The CFW-11 features the Multipump Control function which is capable of controlling up to 5 pumps in order to maintain the pipeline pressure constant regardless of the outflow fluctuations.In this system, an control algoritm of pumps is done by the VSD, which decidesthe moment to start or stop each of the pumps based on the outflow demand. Besides that, the VSD also monitors the suction pressure and the tank level.The CFW-11 also alternates the pumps according to their using time, thus ensuring an uniform wear and tear of motors and pumps.Two types of Multipump Control are available: fixed and floating controls. In fixed control, the VSD is able to control one of the pumps at variable speed and to start and stop other 4 pumps at fixed speed. In floating control, the VSD is able to control up to 4 pumps, all of them at variable speed.
www.weg.net
CFW-11 15
SuperDrive G2 It is a Windows-based software for CFW-11 programming, command and monitoring. The following features are available in the software:g Automatic CFW-11 identifi cationg Monitoring of CFW-11 parametersg Online changing of parameters in the CFW-11g Offl ine changing of parameters in the PCg Creation of application documentsg Trace function (see below)g Upload of SoftPLC applicative software in the CFW-11 fl ash memory (see page 17)g Online troubleshooting
This software is available free of charge at www.weg.net
USB Connection
Trace Function Trace function is used to register CFW-11 variables (like current, voltage, speed, etc.) when a given event occurs in the system (eg.: alarm / fault, overload, overvoltage, etc.).This event in the system is called a trigger because it triggers the data storage process.The stored variables can be visualized in the form of graphs by using the SuperDrive G2 software. Trace function simulates a 4-channel oscilloscope.It is a very useful tool in the start-up of a system and in the diagnoses of defects.
Trace function confi guration in the SuperDrive G2
Example of graph visualization screen
Parameter settingIntegrated environment
Monitoring and command window using virtual Keypad. Start/Stop function, JOG, local / remote, Reverse and reset
Status monitoringMonitoring and parameterization of the list of parameters. Comparison to factory default is easy.
www.weg.net
CFW-1116
USB Connection
SoftPLC Function It is a resource that provides PLC features to the CFW-11 without the addition of any accessories. It provides fl exibility to the product, allowing the user to create his/her own applicative software (user’s program). The SoftPLC main features are:g Ladder language programming using WLP softwareg Access to all VSD parameters and I/Osg Confi gurable PLC, mathematical and control blocksg Applicative software download, upload and online monitoring via USB connectiong Storage of the applicative software in the CFW-11 Flash g Memory Module (see below)g Memory space of 15kB for applicative storage
g 40 User parameter settings that can be individually programmed allowing tags, units, minimum and maximum values, number of decimal digits and other characteristics to be changed.
Simple and practical programming environment
Flash Memory Module g It stores the image of the CFW-11 parameters. It ensures that the programming will not be lost because there is a backup of the parameters.g It permits the transfer of parameters stored in the fl ash Memory Module to the CFW-11 and vice versa. Excellent function for machine manufactures or in processes where parameter settings is repeated (Copy Function).g It stores the applicative software generated by the SoftPLC function.
Standard on CFW11 series
www.weg.net
CFW-11 17
General Input
Rectifi er Unit
Supply Network Single DC Link
CFW-11
1 2 3 4 n 1 2 3 4 n 1 2 3 4 n 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4 1 2 3 4
Technical Features
Built-in DC link Reactorg Allows the VSD to be installed in any network (there is no minimum impedance restriction).g Typical power factor for rated condition: 0.94 for models with three-phase supply 0.70 for models with single-phase or single-phase/three-phase supplyg Meets the 61000-3-12 standard, related to low order current harmonics in the network.
Single DC BusbarUsually used in multi-motor systems, common DC bus confguration is a good solution for energy savings.In this confguration, individual VSD rectifer bridges are replaced with a common input rectifer unit.Each VSD is then directly fed from the DC bus to its DC link terminals.This solution allows the energy in the DC bus to be shared among the VSDs connected to it, thus optimizing the power consuption in the system.The standard CFW-11 can be conected to a DC bus system. ( When required the factory should be consulted for further details)
Intelligent Thermal Managementg Monitoring of the heatsink and internal air temperatures of the electronic boards providing total protection of the IGBTs and the CFW-11 as a whole.g The heatsink fan is turned on and off automatically, depending on the temperature of the power modules.g The speed and the number of hours of operation of the fan are monitored and indicated in corresponding parameters. Alarm or fault messages are generated related to these variables.g The fan is easily removed for cleaning or replacement.
g All CFW-11 models from size A to D have built-in braking IGBT in the standard product;gCFW-11 size E the braking IGBT is optional built-in;gCFW-11 sizes F and G, Breaking IGBT is optional with the external DBW module;gCFW-11 can monitor the temperature probes of the motor (PTC, PT100 OR KTY84), providing thermal protection to the motor (optional accessory is necessary);gOperating air temperature up to 50º C (122º F) for sizes A to D, and up to 45º C (113º F) for size E;g Motor overload protection according to IEC 60497-4-2 and UL 508 C.
Functionsg Multi-speed: up to 8 pre-programmed speeds.g PID regulator: automatic control of level, pressure, fl ow, weight, etc.g Ride-Through: operation during momentary Loss of the power of thepower supply.g Skip Frequency: rejection of critical or resonant speeds.g S Ramp: smoothness in the acceleration / deceleration.
No need for external line reactor
www.weg.net
CFW-1118
Technical Features
(Slot 4 Anybus)
1)
2)
3)
Notes: 1) Half controlled bridge rectifier for sizes F and G;2) Standard for sizes A to D;3) Standard RFI filter for sizes E, F and G;
Please refer to the user manual for more information.
www.weg.net
CFW-11 19
Drive Ratings
Normal Duty (ND) Cycle:g 110% during 60 seconds every 10 minutesg 150% during 3 seconds every 10 minutes
Sizing the drive:The correct way to select a VSD is matching its output current with the motor rated current. However, the tables below present the expected motor power for each VSD model.Use the motor power ratings below only as a guidance. Motor rated currents may vary with speed and manufacturer. IEC motor powers are based on WEG 4-pole motors, NEMA motor powers are based on NEC table 430-150.
Motor voltages between 220V and 230V:
Motor voltages between 380V and 460V:
Normal Duty (ND)
IEC NEMAHeavy Duty
(HD)
IEC NEMA
50 Hz 220 V 230 V
60 Hz 230 V
50 Hz 220 V 230 V
60 Hz 230 V
Power Supply
ModelA kW HP A kW HP
200-240 V
1Ø
CFW110006S2 6 1.1 1.5 5 1.1 1
CFW110007S2 7 1.5 2 7 1.5 2
CFW110010S2 10 2.2 3 10 2.2 3
1/3ØCFW110006B2 6 1.1 1.5 5 1.1 1
CFW110007B2 7 1.5 2 7 1.5 2
3Ø
CFW110007T2 7 1.5 2 5.5 1.1 1
CFW110010T2 10 2.2 3 8 1.5 2
CFW110013T2 13 3 3 11 2.2 3
CFW110016T2 16 4 5 13 3 3
CFW110024T2 24 5.5 7.5 20 5.5 5
CFW110028T2 28 7.5 10 24 5.5 7.5
CFW110033T2 33.5 9.2 10 28 7.5 10
CFW110045T2 45 11 15 36 9.2 10
CFW110054T2 54 15 20 45 11 15
CFW110070T2 70 18.5 25 56 15 20
CFW110086T2 86 22 30 70 18.5 25
CFW110105T2 105 30 40 86 22 30
220-230V 3Ø
CFW110142T2 142 37 50 115 30 40
CFW110180T2 180 55 60 142 37 50
CFW110211T2 211 55 75 180 55 60
Normal Duty (ND)
IEC NEMA
Heavy Duty (HD)
IEC NEMA
50 Hz 380 V 415 V
60 Hz 440 V 460 V
60 Hz 460 V
50 Hz 380 V 415 V
60 Hz 440 V 460 V
60 Hz 460 V
Power Supply
ModelA kW HP HP A kW HP HP
380-480 V 3Ø
CFW110003T4 3.6 1.5 2 2 3.6 1.5 2 2
CFW110005T4 5 2.2 3 3 5 2.2 3 3
CFW110007T4 7 3 4 3 5.5 2.2 3 3
CFW110010T4 10 4 7.5 5 10 4 7.5 5
CFW110013T4 13.5 5.5 10 7.5 11 4 7.5 7.5
CFW110017T4 17 7.5 12.5 10 13.5 5.5 10 7.5
CFW110024T4 24 11 15 15 19 9.2 12.5 10
CFW110031T4 31 15 20 20 25 11 15 15
CFW110038T4 38 18.5 30 25 33 15 25 20
CFW110045T4 45 22 30 30 38 18.5 30 25
CFW110058T4 58.5 30 40 40 47 22 30 30
CFW110070T4 70.5 37 50 50 61 30 50 40
CFW110088T4 88 45 75 60 73 37 60 50
CFW110105T4 105 55 75 75 88 45 75 60
CFW110142T4 142 75 100 100 115 55 75 75
CFW110180T4 180 90 150 150 142 75 100 100
CFW110211T4 211 110 175 150 180 90 150 150
CFW110242T4 242 110 200 200 211 110 150 150
CFW110312T4 312 160 250 250 242 110 200 200
CFW110370T4 370 185 300 300 312 160 250 250
CFW110477T4 477 250 400 400 370 185 300 300
CFW110515T4 515 250 400 450 477 250 400 400
CFW110601T4 601 315 500 500 515 250 400 450
CFW110720T4 720 370 600 600 560 300 450 450
Heavy Duty (HD) Cycle:g 150% during 60 seconds every 10 minutesg 200% during 3 seconds every 10 minutes
www.weg.net
CFW-1120
NEMA 1 / IP21 IP54
Model SizeDimensions
mm (in) Weight kg (lb)
SizeDimensions
mm (in) Weight kg (lb)
Braking IGBTHigh (H) Width (W) Depth (D) High (H) Width (W) Depth (D)
CFW110006S2
A247
(9.73)145
(5.71)227
(8.94)6.3
(13.9)1
410 (16.14)
255 (10.04)
235 (9.25)
10 (22.0)
Standard
CFW110006B2CFW110007S2CFW110007B2CFW110007T2CFW110010S2CFW110010T2CFW110013T2CFW110016T2CFW110024T2
B293
(11.54)190
(7.48)227
(8.94)10.4
(22.9)15
(33.1)CFW110028T2CFW110033T2CFW110045T2
C378
(14.88)220
(8.67)293
(11.54)20.5
(45.2)2
625 (24.61)
350 (13.78)
298 (11.73)
36 (79.4)
CFW110054T2CFW110070T2CFW110086T2
D504
(19.84)300
(11.81)305
(12.01)32.6
(71.8)41
(90.4)CFW110105T2CFW110142T2
E675
(26.58)335
(13.19)358
(14.09)65
(143.3)- - - - - OptionalCFW110180T2
CFW110211T2CFW110003T4
A247
(9.73)143
(5.63)196
(7.72)6.3
(13.9)1
410 (16.14)
255 (10.04)
235 (9.25)
10 (22.0)
Standard
CFW110005T4CFW110007T4CFW110010T4CFW110013T4CFW110017T4
B293
(11.54)190
(7.48)227
(8.94)10.4
(22.9)15
(33.1)CFW110024T4CFW110031T4CFW110038T4
C378
(14.88)220
(8.67)293
(11.54)20.5
(45.2)2
625 (24.61)
350 (13.78)
298 (11.73)
36 (79.4)
CFW110045T4CFW110058T4CFW110070T4
D504
(19.84)300
(11.81)305
(12.01)32.6
(71.8)41
(90.4)CFW110088T4CFW110105T4
E675
(26.58)335
(13.19)358
(14.09)65
(143.3)3
875(34.45)
400 (15.75)
374 (14.72)
80 (276)
OptionalCFW110142T4CFW110180T4CFW110211T4CFW110242T4
F1200
(47.24)430
(16.93)360
(14.17)140
(308.65)- - - - - Optional
CFW110312T4CFW110370T4CFW110477T4CFW110515T4
G1225
(48.23)535
(21.06)426
(16.77)215
(473.99)- - - - - OptionalCFW110601T4
CFW110720T4
Dimensions and Weight
H
W
D
www.weg.net
CFW-11 21
Mechanical Mounting
Standard Installation
When one VSD is assembled on the top of another, use the distance A+B and defl ect the hot air coming from the VSD below.
A
B
C
Side by side Installation
For Frame Size A, B and C: side by side assembly without lateral spacing and with the removal of the top cover.
Frame SizeMinimum Mounting Clearance
A mm (in) B mm (in) C mm (in) D mm (in)
A 25 (0.98) 25 (0.98) 10 (0.39) 30 (0.39)
B 40 (1.57) 45 (1.57) 10 (0.39) 30 (0.39)
C 110 (4.33) 130 (5.12) 10 (0.39) 30 (0.39)
D 110 (4.33) 130 (5.12) 10 (0.39) 30 (0.39)
E, F and G 150 (5.91) 250 (9.84) 20 (0.78) 80 (3.15)
D
www.weg.net
CFW-1122
Mechanical Installation | Panel Assembly
Surface Assembly
Flange Assembly (IP-54 rated when mounting the heat-sink outside the enclosure)
Airfl owAirfl ow
Frame Size a2 mm (in) b2 mm (in) c2 mm (in)
A 115 (4.53) 250 (9.85) M5
B 150 (5.91) 300 (11.82) M5
C 150 (5.91) 375 (14.77) M6
D 200 (7.88) 525 (20.67) M8
E 200 (7.88) 650 (25.60) M8
F 150 (5.91) 1200 (47.24) M10
G 200 (7.87) 1225 (48.23) M10
Frame Size a3 mm (in) b3 mm (in) c3 mm (in) d3 mm (in) e3 mm (in)
A 130 (5.12) 240 (9.45) M5 135 (5.32) 225 (8.86)
B 175 (6.84) 285 (11.23) M5 179 (7.05) 271 (10.65)
C 195 (7.68) 365 (14.38) M6 205 (8.08) 345 (13.59)
D 275 (10.83) 517 (20.36) M8 285 (11.23) 485 (19.10)
E 275 (10.83) 635 (25.00) M8 315 (12.40) 615 (24.21)
F 350 (13.78) 1185 (46.61) M10 391 (15.39) 1146 (45.12)
G 400 (15.75) 1220 (48.03) M10 495 (19.49) 1182 (46.53)
Airfl owAirfl owAirfl ow
Sizes A up to E Sizes F and G
* For Sizes F and G the inverter area that will be outside the panel has only IP20 protection degree.
www.weg.net
CFW-11 23
Technical Data
Power supply and Power Range
Voltage and power range
Sigle Phase 200-240Vac / +10% - 15%1.5 to 3 HP (1.1 to 2.2 kW)
Three Phases
200-240Vac / + 10% -15%:1.5 to 75 HP (1.1 to 55 kW)380-480Vac / + 10% -15%:2 to 600 HP (1.5 to 370 kW)
Frequency 50...60 Hz +/-2% (48 to 63 Hz)
Displacement factor Greater than 0.98
Efficiency Greater than 0.97
Power factor 0.94 for three-phase input at rated condition0.70 for single-pahse input at rated condition
Inverter Output
Voltage range Three Phase, 0 up to power supply voltage
Frequency range 0 to 3.4x motor rated frequency (*)
Switching Frequency
Standard: 5 kHz (frame sizes A, B, C, D); 2,5 kHz (frame sizes E and F);
2 kHZ (frame size G)Options available 2.5 / 5 / 10 kHz
Overload
Normal Duty Cycle 110% for 1 min every 10min
150% for 3 sec every 10min
Heavy Duty Cycle150% for 1 min every 10min
200% for 3 sec every 10min
Time (ramps)
Acceleration 0 to 999 seconds
Deceleration 0 to 999 seconds
Performance
V/f
Speed Control
Regulation: 1% of rated speed
Speed variation range: 1:20
Voltage Vector (VVW)
Regulation: 1% of rated speed
Speed variation range: 1:30
Sensorless VectorRegulation: 0.5% of rated speed
Speed variation range: 1:100
Vector with Encoder
(with accessory ENC-01 or ENC-02)
Regulation: +/- 0.01% of rated speed with 14-bit analog input (IOA)
Regulation: +/- 0.01% of rated speed with digital reference (keyboard, serial fieldbus, electronic potentiometer,
multispeed)
Regulation: +/- 0.05% of rated speed with 12-bit analog input
Torque Control
Range: 10 to 180%
Regulation: +/- 5% of rated torque
Sensorless Vector
Range: 20 to 180%
Regulation: +/-10% of rated torque (above 3 Hz)
Protection Degree
IP20Frame Size A, B and C without upper cover and conduit kit and
frame size E without conduit kit
NEMA 1 / IP20Frame Size D without IP21 kit Frame size E with conduit kit
IP21 Frame Size A, B and C with upper cover and conduit kit
NEMA 1 / IP21Frame Size A, B and C with upper cover and conduit kit
Frame Size D with IP21 kit
Braking Methods
Rheostatic Braking
Supply available to user (standard for frame size A, B, C and D and option for frame size E)
External braking resistor (not provided)
Optimal Braking Does not need braking resistor
DC Braking Direct current applied to the motor
Inputs and Outputs (I/Os) in the Standard Product
Inputs
Digital 6 isolated inputs, 24 Vdc, programmable functions
Analog
2 differential inputs isolated by differential amplifier, programmable functions
Resolution:- AI1: 12 bits- AI2: 11 bits + signal
Signals: 0 to 10Vdc, 0 to 20mA or 4 to 20mA
Impedance:- 400 kΩ for signal 0 to 10Vdc - 500 Ω for signal 0 to 20mA or 4 to 20mA
Outputs
Relay3 relays with NO / NC contacts, 240 Vac / 1A, pro-grammable functions
Analog
2 isolated outputs, programmable functions
Resolution: 11 bits
Load:0 to 10 V: RL >= 10 kΩ0 to 20 mA or 4 to 20 mA: RL < 500Ω
Available supply to user
24 Vdc + -20%, 500 mA
(*) This maximum value can change according to the used control mode and switching frequency. The maximum permissible speed is 18000rpm.
Environment
Temperature of Operation
-10 to 50°C (14 to 122°F) for frame Size A,B,C and D-10 to 45°C (14 to 113°F) for frame Size E, F and G models
Up to 60°C (140°F) for frame Size A,B,C,D and 55°C (133°F) for frame Size E with current derating (2% for each 1°C
above rated value or 1.1% for each 1°F above rated value)
rated value or 1.1% for each 1°F above rated value
Humidity 5 to 90% without condensation
Altitude0 to 1000 meters
Up to 4000 meters with current reduction(1% for every 100 meters above 1000 meters)
www.weg.net
CFW-1124
Protections
Overcurrent / short circuit
Under / overvoltage in the power circuit
Phase loss
Overtemperature in the VSD (IGBTs, rectifier and internal air
in the electronic cards)
Overtemperature in the motor
Overload in the braking resistor
Overload in the IGBTs
Overload in the motor
Fault / external alarm
Fault in the CPU or memory
Phase-to-ground short circuit at the output
Fault in the heatsink fan
Overspeed of motor
Incorrect connection of encoder
Communication
Profibus DP PROFIBUS DP-05 (slot 3 and 4)
DeviceNet
CAN/RS485-01 (slot 3)
CAN-01 (slot 3)
DEVICENET-05 (slot4)
CANopenCAN/RS485-01 (slot 3)
CAN-01 (slot 3)
CANopen Master/Slave PLC11-01 1, 2 and 3
Ethernet TCP/IP ETHERNET/IP-05 (slot 4)
ModBus RTU(RS-485)
RS485-01 (slot 3)
CAN/RS485-01 (slot 3)
RS485-05 (slot 4)
ModBus RTU (RS-232)
RS232-01 (slot 3)
RS232-05 (slot 4)
USB
Built into the standard product
Communication with SuperDrive G2 Software
Communication with WLP Software used for programming and monitoring the SoftPLC
function and the PLC11 accessories
Safety Standards
UL 508CPower conversion equipment
UL 840Insulation coordination including clearances and creepage distances
for electrical equipment
EN 61800-5-1 Safety requirements electrical, thermal and energy
EN 50178Electronic equipment for use in power installations
EN 60204-1Safety of machinery.
Electrical equipment of machines. Part 1: General requirements.
Note: In order to have a machine in conformity with this norm, the machine manufacturer is responsible for the installation of an
emergency shutdown device and an equipment for network sectioning
EN 60146 (IEC 146) Semiconductor converters
EN 61800-2 Adjustable speed electrical power drive systems – Part 2: General
requirements – rating specifications for low voltage adjustable frequency a.c. power drive systems
Electromagne Compatibility Standards (EMC)
EN 61800-3 - Adjustable speed electrical power drive systems Part 3: EMC product standard including specific test methods
EN 55011 - Limits and methods of measurement of radio disturbance characteristics of industrial, scientific and medical (ISM) radio-frequency
equipment
CISPR 11 - Industrial, scientific and medical (ISM)radio-frequency equipment Electromagnetic disturbance characteristics Limits and methods
of measurement
EN 61000-4-2 - Electromagnetic Compatibility Standards (EMC) Part 4: Testing and measurement techniques -
Section 2: Electrostatic discharge immunity test
EN 61000-4-3 - Electromagnetic Compatibility Standards (EMC) Part 4: Testing and measurement techniques -
Section 3:Radiated, radiofrequency, electromagnetic field immunity test
EN 61000-4-4 - Electromagnetic Compatibility Standards (EMC) Part 4: Testing and measurement techniques -
Section 4: Electrical fast transient / burst immunity test
EN 61000-4-5 - Electromagnetic Compatibility Standards (EMC) Part 4: Testing and measurement techniques -
Section 5: Surge immunity test
EN 61000-4-6 - Electromagnetic Compatibility Standards (EMC) Part 4: Testing and measurement techniques -
Section 6: Immunity to conducted disturbances, induced by radio-frequency fields
Technical Data
Mechanical Construction Standards
EN 60529 - Degrees of protection provided by enclosures (IP Code)
UL 50 - Enclosures for electrical equipment
www.weg.net
CFW-11 25
1 - Market identificationIt defines the language of the manual and the factory parameterizationBR = Brazil NA = North America MS = MercosulEU = EuropeSA = South Africa
2 - Line CFW11 = WEG Frequency VSD series CFW11
Coding
EU CFW11 0016 T 4 S _ _ _ _ _ _ _
_ Z1 2 3 4 5 6 7 8 9 10 11 12 13 14 15
3- Rated output current for normal overload system
4 – Number of phasesS = Single-phaseB = Single-phase or three-phaseT = Three-phase
5 - Voltage2 = 200-240 V4 = 380-480 V
6 - Optional AccessoriesS = standard productO = product with optional accessories
7 - Degree of Protection Blank = factory standard (Sizes A, B and C: IP21 - D: Nema 1/ IP20)N1 = Nema 121 = IP21
8 - KeypadBlank = factory standard (1)IC = without interface (blind cover)
9 - BrakingBlank = factory standard (Sizes A, B, C , D: built-in braking IGBT) DB = with braking IGBT (valid for models of frame size E)
10 - RFI Filter Blank = factory standardFA = Category C3 internal RFI filter(Valid for models of frame (size E: built-in RFI filter) Size A, B, C and D)
11 - Safety StopBlank = factory standard (without safety stop function)Y = with safety stop function according to EN-954-1 category 3
12 - External Electronic Supply 24 Vdc Blank = factory standard W= With external eletronic power supply 24Vdc( Sizes A,B,C,D,E: Without external eletronic power supply 24vdc in the standard product)
13 – Special hardwareBlank = factory standard (without)H1 = special hardware nr. 1
14 – Special SoftwareBlank = factory standard (without)S1 = special software nr. 1
15 – End of Code indicator digitZ = end of code indicator
Supply Single-phase (S) Single-phase or Three-phase (B) Three-Phase (T)
Voltage
200 - 240 V (2) 200 - 240 V (2) 200-240 V (2) 380-480 V (4)
0010 = 10 A 0006 = 6 A
0007 = 7 A
0007 = 7 A0010 = 10 A0013 = 13 A0016 = 16 A0024 = 24 A0028 = 28 A0033 = 33 A0045 = 45 A0054 = 54 A0070 = 70 A0086 = 86 A0105 = 105 A 0142 = 142 A0180 = 180 A0211 = 211 A
0003 = 3 A0005 = 5 A0007 = 7 A0010 = 10 A0013 = 13 A0017 = 17 A0024 = 24 A0031 = 31 A0038 = 38 A0045 = 45 A0058 = 58 A0070 = 70 A
0088 = 88 A 0105 = 105 A0142 = 142 A0180 = 180 A0211 = 211 A0242 = 242 A0312 = 312 A0370 = 370 A0477 = 477 A0515 = 515 A0601 = 601 A0720 = 720 A
www.weg.net
CFW-1126
CFW11M - Modular Drive
Power Units Compact modular VSD units that can be confi gured to the applicable motor power.g Easy servicing.g Confi gurable up to 5 power units.g DC supplied by an input rectifi er.g Compact book format (width much smaller than
the depth).
The CFW-11M (modular drive) is the new generation of WEG VSDs for large powers. It is available at power ratings from 400 to 2500 HP and voltages from 500 to 690 V, with 6 and 12 pulse inputrectifi er.
Notes: The fuses presented in the block diagram above are not included in the VSD CFW-11M, but are part of the AFW-11M drive Maximum AFW-11M confi guration with 5 power units (2500 HP)
Confi gurable up to 5 power book units
Power Book Unit
DC Link (connected to rectifi er)
Output to motor
www.weg.net
CFW-11 27
Sizing the Drive The correct way to select a VSD is matching its output current with the motor rated current. However, the tables below present the expected motor power for each VSD model.Use the motor power ratings below only as a guidance. Motor rated currents may vary with speed and manufacturer. IEC motor powers are based on WEG 4-pole motors; NEMA motor powers are based on NEC table 430-150.
Motor Voltages between 380-480V
CFW11M - Drive Ratings
Motor Voltages between 500-600V
Motor Voltages between 660-690V
Normal Duty (ND)
IEC NEMA
Heavy Duty (HD)
IEC NEMA
50 Hz 380 V 415 V
60 Hz 380 V 460 V
60 Hz 460 V
50 Hz 380 V 415 V
60 Hz 380 V 460 V
60 Hz 460 V
Power Supply
ModelA kW HP HP A kW HP HP
380-
480
V
3Ø
CFW11M 0600T4 600 315 450 500 515 280 350 450
CFW11M 1140T4 1140 630 850 1000 979 500 700 800
CFW11M 1710T4 1710 900 1250 1500 1468 800 1100 1250
CFW11M 2280T4 2280 1250 1750 2000 1957 1120 1350 1750
CFW11M 2850T4 2850 1600 2000 2500 2446 1250 1750 2000
Normal Duty (ND)
IEC NEMAHeavy Duty
(HD)
IEC NEMA
50 Hz 525 V 575 V
60 Hz 575 V
60 Hz 575 V
50 Hz 525 V 575 V
60 Hz 575 V
60 Hz 575 V
Power Supply
ModelA kW HP HP A kW HP HP
500-
600
V
3Ø
CFW11M 0470T5 470 355 500 500 380 280 400 400
CFW11M 0893T5 893 630 1000 1000 722 500 800 800
CFW11M 1340T5 1340 1000 1350 1500 1083 800 1250 1100
CFW11M 1786T5 1786 1250 1750 1750 1444 1120 1500 1350
CFW11M 2232T5 2232 1600 2500 2500 1805 1400 2000 2000
Normal Duty (ND)
IEC
Heavy Duty (HD)
IEC
50 Hz 660 V 690 V
60 Hz 660 V
50 Hz 660 V 690 V
60 Hz 660 V
Power Supply
Model A kW HP A kW HP
660-
690
V
3Ø
CFW11M 0427T6 427 400 550 340 315 400
CFW11M 0811T6 811 710 1000 646 560 800
CFW11M 1217T6 1217 1120 1500 969 900 1250
CFW11M 1622T6 1622 1600 2000 1292 1250 1750
CFW11M 2028T6 2028 2000 2500 1615 1400 2000
5001
9076
.05/
0420
10 -
The
val
ues
show
n ar
e su
bje
ct to
cha
nge
with
out p
rior
notic
e.
WEG Equipamentos Elétricos S.A.International Division Av. Prefeito Waldemar Grubba, 3000 89256-900 - Jaraguá do Sul - SC - Brazil Phone: 55 (47) 3276-4002 Fax: 55 (47) 3276-4060 www.weg.net
WEG Worldwide Operations
ARGENTINAWEG EQUIPAMIENTOS ELECTRICOS S.A.(Headquarters San Francisco-Cordoba)Sgo. Pampiglione 4849Parque Industrial San Francisco2400 - San FranciscoPhone(s): +54 (3564) 421484Fax: +54 (3564) [email protected]/ar
AUSTRALIAWEG AUSTRALIA PTY. LTD.3 Dalmore DriveCarribean Park Industrial EstateScoresby VIC 3179 - MelbournePhone(s): 61 (3) 9765 4600Fax: 61 (3) 9753 [email protected]/au
BELGIUM WEG BENELUX S.A.Rue de l’Industrie 30 D, 1400 NivellesPhone(s): + 32 (67) 88-8420Fax: + 32 (67) 84-1748 [email protected]/be
CHILEWEG CHILE S.A.Los Canteros 8600 La Reina - SantiagoPhone(s): (56-2) 784 8900Fax: (56-2) 784 [email protected]/cl
CHINAWEG (NANTONG) ELECTRIC MOTOR MANUFACTURING CO., LTD.No. 128# - Xinkai South Road,Nantong Economic & Technical Development Zone, Nantong, Jiangsu Province. Phone(s): (86) 0513-85989333Fax: (86) [email protected]/cn
COLOMBIAWEG COLOMBIA LTDACalle 46A N82 - 54Portería II - Bodega 7 - San Cayetano II - BogotáPhone(s): (57 1) 416 0166Fax: (57 1) 416 [email protected]/co
FRANCEWEG FRANCE SASZI de Chenes – Le Loup13 Rue du Morellon – BP 73838297 Saint Quentin FallavierPhone(s): +33 (0) 4 74 99 11 35Fax: +33 (0) 4 74 99 11 [email protected]/fr
GERMANYWEG GERMANY GmbHIndustriegebiet Türnich 3Geigerstraße 750169 Kerpen-TürnichPhone(s): +49 (0)2237/9291-0Fax: +49 (0)2237/[email protected]/de
INDIAWEG Electric (India) Pvt. Ltd.#38, Ground Floor, 1st Main Road, Lower Palace Orchards,Bangalore – 560 003Phone(s): +91-80-4128 2007 +91-80-4128 2006 Fax: +91-80-2336 7624 [email protected]/in
ITALYWEG ITALIA S.R.L.V.le Brianza 20 - 20092 - Cinisello Balsamo - MilanoPhone(s): (39) 02 6129-3535Fax: (39) 02 [email protected]/it
JAPANWEG ELECTRIC MOTORSJAPAN CO., LTD.Yokohama Sky Building 20F, 2-19-12 Takashima, Nishi-ku, Yokohama City,Kanagawa, Japan 220-001Phone: (81) 45 440 [email protected]/jp
MEXICOWEG MEXICO, S.A. DE C.V.Carretera Jorobas-Tula Km. 3.5, Manzana 5, Lote 1 Fraccionamiento Parque Industrial - Huehuetoca, Estado de México - C.P. 54680Phone(s): + 52 (55) 5321 4275Fax: + 52 (55) 5321 [email protected]/mx
NETHERLANDSWEG NETHERLANDS Sales Office of WEG Benelux S.A.Hanzepoort 23C 7575 DB OldenzaalPhone(s): +31 (0) 541-571080Fax: +31 (0) [email protected]/nl
PORTUGALWEG EURO - INDÚSTRIA ELÉCTRICA, S.A.Rua Eng. Frederico UlrichApartado 6074 4476-908 - MaiaPhone(s): +351 229 477 705Fax: +351 229 477 [email protected]/pt
RUSSIAWEG RUSSIA Pochainskaya Str. 17 Nizhny Novgorod 603001 - Russia Phone(s): +7-831-2780425 Fax: [email protected] www.weg.net/ru
SPAINWEG IBERIA S.L. Avenida de la Industria,2528823 Coslada - MadridPhone(s) : (34) 916 553 008Fax : (34) 916 553 [email protected]/es
SINGAPOREWEG SINGAPORE PTE LTD159, Kampong Ampat, #06-02A KA PLACE. Singapore 368328.Phone(s): +65 6858 9081Fax: +65 6858 [email protected]/sg
SWEDENWEG SCANDINAVIA ABBox 10196Verkstadgatan 9434 22 KungsbackaPhone(s): (46) 300 73400Fax: (46) 300 [email protected]/se
UKWEG ELECTRIC MOTORS (U.K.) LTD.28/29 Walkers RoadManorside Industrial EstateNorth Moons Moat - RedditchWorcestershire B98 9HEPhone(s): 44 (0)1527 596-748Fax: 44 (0)1527 [email protected]/uk
UNITED ARAB EMIRATESWEG MIDDLE EAST FZEJAFZA – JEBEL ALI FREE ZONETower 18, 19th Floor, Office LB 18 1905P.O. Box 262508 - DubaiPhone: +971 (4) 8130800 Fax: +971 (4) [email protected]/ae
USAWEG ELECTRIC CORP. 6655 Sugarloaf Parkway, Duluth, GA 30097 Phone(s): 1-678-249-2000Fax: [email protected] www.weg.net/us
VENEZUELAWEG INDUSTRIAS VENEZUELA C.A.Avenida 138-AEdificio Torre Banco Occidental de Descuento, Piso 6 Oficina 6-12Urbanizacion San Jose de TarbesZona Postal 2001Valencia, Edo. CaraboboPhone(s): (58) 241 8210582 (58) 241 8210799 (58) 241 8211457Fax: (58) 241 [email protected]/ve