CEMA B4 & C5 CLASS IDLERS - Conveyor Pulley...
8
CEMA B4 & C5 CLASS IDLERS EQUAL TROUGHING IDLER RETURN IDLER TROUGHED IMPACT IDLER FLAT CARRIER
Transcript of CEMA B4 & C5 CLASS IDLERS - Conveyor Pulley...
CEMA B4 & C5 CLASS IDLERS
Equal troughing idlEr
rEturn idlEr
troughEd impact idlEr
flat carriEr
VG_TroughingIdler_B4&C5.indd 1 5/2/13 9:35 AM
Also The Finest and Most Complete Line of Conveyor Pulleys!
High quality maintenance-free
ball bearings
Energy savings from 25% less roll-drag.
Outer metal labyrinth seal
bEaring & sEal arrangEmEnt
stationary outer shield
inner triple labyrinth seal pressed onto shaft
and into bearing cup
maintenance-free, high-quality, low-drag,
deep groove ball bearings
internal nitrile seal
call 1-800-Van-gorp (826-4677) for all of your idler needs! or email [email protected]
self-cleaning centrifical
action
VG_TroughingIdler_B4&C5.indd 2 5/2/13 9:35 AM
Also The Finest and Most Complete Line of Conveyor Pulleys!
rEturn idlEr Carries empty belt on the return run.
Equal trOugHing idlErtroughed belt idlers are available in roll inclinations of 20, 35 and 45 degrees.
trOugHEd impaCt idlErtroughed belt rubber cushion idlers protect the belt by absorbing impacts at loading and transfer points. they are available in inclinations of 20, 35 and 45 degrees.
flat CarriErused for picking and sorting conveyors.
also available in heavy duty live shaft design.
Van gorp idlers conform to CEma standards fordimensions and meet or exceed CEma load ratings.
High quality maintenance-free
ball bearings
roller end welds protectedfrom belt wear
narrow roll gaps
quick change rolls
deep formed channel end brackets for
extra strength
Heavy duty foot brackets made for
one or two bolt mountingself cleaning
cross member non-Clogging center stands
VG_TroughingIdler_B4&C5.indd 3 5/2/13 9:35 AM
B4 EQUAL TROUGHING IDLERS
Assembly Description E H K Assembly Weight A C Bmin D L
B4-20TE-18 9.42 20.69 7.0 31 27 29.0 5.5 9.5 6.75B4-35TE-18 11.11 18.94 7.0 35B4-20TE-20 9.81 23.25 7.0 33 29 31.0 5.5 9.5 7.63B4-35TE-20 11.50 21.25 7.0 37B4-20TE-24 10.14 27.04 7.0 38 33 35.0 5.5 9.5 8.94B4-35TE-24 12.31 24.69 7.0 39B4-20TE-30 10.88 33.33 7.0 42 39 41.0 5.5 9.5 11.13B4-35TE-30 13.56 30.50 7.0 45B4-20TE-36 11.61 39.45 7.0 48 45 47.0 5.5 9.5 13.25B4-35TE-36 14.78 36.13 7.0 50B4-20TE-42 12.94 45.75 7.5 54 51 53.5 5.5 9.5 15.44B4-35TE-42 16.44 41.88 7.5 56
CEMA Load Ratings for CEMA B Idlers (Lbs)
Idler Class Belt Width (In)
Trough Single Roll Return Two Roll Vee Return
20˚ 35˚ 45˚
CEMA B
18 410 410 410 22020 410 410 410 20024 410 410 410 19030 410 410 410 16536 410 410 396 15542 390 363 351 140
*Van Gorp Idlers meet or exceed CEMA standards.
VG_TroughingIdler_B4&C5.indd 4 5/2/13 9:35 AM
B4 RETURN IDLERS
Assembly Description E Bmin D Assembly Weight A C L
B4-1R-18 1.5 4.000 6.0 1427 29 21.38
B4-4R-18 4.5 3.563 8.0 15
B4-1R-20 1.5 4.000 6.0 1529 31 23.38
B4-4R-20 4.5 3.563 8.0 17
B4-1R-24 1.5 4.000 6.0 1633 35 27.38
B4-4R-24 4.5 3.563 8.0 18
B4-1R-30 1.5 4.000 6.0 1939 41 33.38
B4-4R-30 4.5 3.563 8.0 20
B4-1R-36 1.5 4.000 6.0 2245 47 39.38
B4-4R-36 4.5 3.563 8.0 23
B4-1R-42 1.5 4.000 6.0 2751 53 45.38
B4-4R-42 4.5 3.563 8.0 28
*Flat Carrier Idlers also available. Same clearance dimensions as the Return Idlers listed.
End Stands for Flat Carrier Idlers
1-1/2” Optional End Stand
5-1/8"
9/16"
2-11/16"
3/16"
4"
6"
4-1/2"
9/16"
2-11/16"
2-1/2" 9/16"
3/16"
9/16"
1-1/2"
4"
6"
4-1/2” Standard End Stand
L
A
C
E
BminD
VG_TroughingIdler_B4&C5.indd 5 5/2/13 9:35 AM
C5 EQUAL TROUGHING IDLERS
Assembly Description E H K Assembly Weight A C Bmin D L
C5-20TE-24 11.69 27.06 8.50 52 33 35.0 5.5 9.50 8.94C5-35TE-24 13.81 24.56 8.50 53C5-20TE-30 12.56 33.38 8.63 59 39 41.5 5.5 9.50 11.13C5-35TE-30 15.19 30.38 8.63 61C5-20TE-36 13.31 39.44 8.63 67 45 47.5 5.5 9.50 13.25C5-35TE-36 16.38 35.94 8.63 69C5-20TE-42 14.44 45.75 9.00 75 51 53.5 5.5 9.50 15.44C5-35TE-42 18.06 41.75 9.00 78C5-20TE-48 15.19 52.06 9.00 83 57 59.5 5.5 9.50 17.63C5-35TE-48 19.31 47.5 9.00 86C5-20TE-54 15.88 58.19 9.00 93 63 65.5 7.0 10.94 19.75C5-35TE-54 20.50 53.13 9.00 100C5-20TE-60 16.56 63.88 9.00 100 69 71.5 7.0 10.94 21.75C5-35TE-60 21.69 58.38 9.00 107
C5 IMPACT TROUGHING IDLERS
Assembly Description E H K Assembly Weight A C Bmin D L
C5-20TEI-24 11.44 25.63 8.50 54 33 35.0 5.5 9.50 8.94C5-35TEI-24 13.38 23.31 8.50 56C5-20TEI-30 12.31 31.94 8.63 66 39 41.5 5.5 9.50 11.13C5-35TEI-30 14.75 29.13 8.63 68C5-20TEI-36 13.06 39.49 8.63 75 45 47.5 5.5 9.50 13.25C5-35TEI-36 15.94 35.18 8.63 77C5-20TEI-42 14.19 45.54 9.00 85 51 53.5 5.5 9.50 15.44C5-35TEI-42 17.63 40.96 9.00 88C5-20TEI-48 14.94 51.81 9.00 96 57 59.5 5.5 9.50 17.63C5-35TEI-48 18.88 46.71 9.00 98C5-20TEI-54 15.63 56.75 9.00 109 63 65.5 7.0 10.94 19.75C5-35TEI-54 20.06 51.88 9.00 115C5-20TEI-60 16.31 62.44 9.00 120 69 71.5 7.0 10.94 21.75C5-35TEI-60 21.25 57.13 9.00 126
VG_TroughingIdler_B4&C5.indd 6 5/2/13 9:35 AM
C5 RETURN IDLERS
Assembly Description E Bmin D Assembly Weight A C L
C5-1R-24 1.5 4.000 6.0 24 33 35 27.38C5-4R-24 4.5 3.563 8.0 26C5-1R-30 1.5 4.000 6.0 29 39 41 33.38C5-4R-30 4.5 3.563 8.0 30C5-1R-36 1.5 4.000 6.0 33 45 47 39.38C5-4R-36 4.5 3.563 8.0 35C5-1R-42 1.5 4.000 6.0 37 51 53 45.38C5-4R-42 4.5 3.563 8.0 39C5-1R-48 1.5 4.000 6.0 42 57 59 51.38C5-4R-48 4.5 3.563 8.0 43C5-1R-54 1.5 4.000 6.0 46 63 65 57.38C5-4R-54 4.5 3.563 8.0 47C5-1R-60 1.5 4.000 6.0 51 69 71 63.38C5-4R-60 4.5 3.563 8.0 53
*Flat Carrier Idlers also available. Same clearance dimensions as the Return Idlers listed.
End Stands for Flat Carrier Idlers
1-1/2” Optional End Stand
5-1/8"
9/16"
2-11/16"
3/16"
4"
6"
4-1/2"
9/16"
2-11/16"
2-1/2" 9/16"
3/16"
9/16"
1-1/2"
4"
6"
4-1/2” Standard End Stand
L
A
C
E
BminD
5-1/8"
9/16"
2-11/16"
3/16"
4"
6"
4-1/2"
9/16"
2-11/16"
2-1/2" 9/16"
3/16"
9/16"
1-1/2"
4"
6"
CEMA Load Ratings for CEMA C Idlers (Lbs)
Idler Class
Belt Width (In)
Trough Single Roll Return
Two Roll Vee Return 20˚ 35˚ 45˚
CEMA C
24 900 900 900 32530 900 900 900 250 50036 900 837 810 200 50042 850 791 765 150 50048 800 744 720 125 50054 750 698 675 * 50060 700 650 630 * 500
*CEMA recommends to use CEMA “D” return idler. **Van Gorp Idlers meet or exceed CEMA standards.
VG_TroughingIdler_B4&C5.indd 7 5/2/13 9:35 AM
Distributed by:
VAN GORP and the VAN GORP LOGO are registered trademarks of Van Gorp Corporation.
B4C5Flyer11.13
1410 Washington stpO box 288
pella, ia 50219(641) 628-9212www.vangorp.biz
MEMBER: NSSGA
D6E7Flyer05.13
VG_TroughingIdler_D6&E7.indd 8 5/7/13 3:16 PM
1410 Washington stpO box 288
pella, ia 50219(641) 628-9212www.vangorp.biz
MEMBER: NSSGA
D6E7Flyer05.13
VG_TroughingIdler_D6&E7.indd 8 5/7/13 3:16 PM
1410 Washington StPO Box 288
Pella, IA 50219www.vangorp.biz
Call 1-800-VANGORP (826-4677)or email your inquiries to:
1410 Washington stpO box 288
pella, ia 50219(641) 628-9212www.vangorp.biz
MEMBER: NSSGA
D6E7Flyer05.13
VG_TroughingIdler_D6&E7.indd 8 5/7/13 3:16 PM
