CCNA 2 Final V4.0 Answers
-
Upload
ccnadiscovery4 -
Category
Documents
-
view
229 -
download
0
Transcript of CCNA 2 Final V4.0 Answers
-
8/14/2019 CCNA 2 Final V4.0 Answers
1/17
-
8/14/2019 CCNA 2 Final V4.0 Answers
2/17
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
Router(config)# enable cisco
Router(config)# encryption-password all
Router(config)# enable login encrypted
Router(config)# enable password encryption
Router(config)# service password-encryption
4
A new network is to be configured on a router. Which of the following tasks must be
completed to configure this interface and implement dynamic IP routing for the newnetwork? (Choose three.)
Select the routing protocol to be configured.
Assign an IP address and subnet mask to the interface.
Update the ip host configuration information with the device name and new interface
IP address.
Configure the routing protocol with the new network IP address.
Configure the routing protocol with the new interface IP address and subnet mask.
Configure the routing protocol in use on all other enterprise routers with the new
network information.
5
How does TCP ensure the reliable transfer of data?
If data segments are not received from the source, the destination requests that thesegments be resent.
If an acknowledgment of the transmitted segments is not received from the destination
in a predetermined amount of the time, the source resends the data.
TCP uses the SYN-ACK portion of the three-way handshake to ensure that all data
has been received.
The TCP Protocol Interpreter process verifies the transmitted data at source and
destination.
-
8/14/2019 CCNA 2 Final V4.0 Answers
3/17
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
6
A network administrator is asked to design a system to allow simultaneous access to
the Internet for 250 users. The ISP for this network can only supply five public IPs.
What can be used to accomplish this task?
routable translation
dynamic translation
static translation
port address translation
7What is the most commonly used exterior routing protocol?
BGP
RIP
OSPF
EIGRP
8
Refer to the exhibit. The network administrator needs to configure the router with a
name. Which command will the administrator use to configure the router name?
Router# ip hostname Boise
Router# enable hostname Boise
Router(config-line)# name Boise
Router(config)# hostname Boise
Router(config)# ip hostname Boise
9
Why are port numbers included in the TCP header of a segment?
to indicate the correct router interface that should be used to forward a segment
to identify which switch ports should receive or forward the segment
-
8/14/2019 CCNA 2 Final V4.0 Answers
4/17
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
to determine which Layer 3 protocol should be used to encapsulate the data
to enable a receiving host to forward the data to the appropriate application
to allow the receiving host to assemble the packet in the proper order
10
What is the purpose of the routing process?
to encapsulate data that is used to communicate across a network
to select the paths that are used to direct traffic to destination networks
to convert a URL name into an IP address
to provide secure Internet file transfer
to forward traffic on the basis of MAC addresses
11
Which two statements are true about the use of the debug ip rip command on a Cisco
router? (Choose two.)
The debug ip rip command displays RIP routing activity in real time.
The debug ip rip command can be issued at the user EXEC configuration mode.
The debug ip rip command displays a combination of the information that is displayed
by the show ip route and show ip protocols commands.
Because of router processor usage, the debug ip rip command should be used only
when necessary.
The debug ip rip command should be used instead of the show ip route commandwhenever possible.
12
What minimum configurations must be set on a host to allow a request to be sent to
http://www.cisco.com/? (Choose four.)
DNS server
WINS server
IP address
http://www.cisco.com/ -
8/14/2019 CCNA 2 Final V4.0 Answers
5/17
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
NetBIOS
subnet mask
default gateway
13
A Catalyst 2960 switch has been taken out of storage to be used as a temporary
replacement for another switch that needs to be repaired. About a minute after the
switch has started, the SYST LED on the front of the switch transitions from blinking
green to amber. What is the meaning of the amber SYST LED?
The switch has no configuration file in NVRAM.
The switch has failed POST and must be sent for service.
The switch is functioning properly.
The switch is in half-duplex mode.
14
Refer to the exhibit. Which combination of cables and symbols is correct?
A - crossover, B - straight-through, C - straight-through
A - crossover, B - rollover, C - straight-through
A - straight-through, B -crossover, C - straight-through
A - straight-through, B -straight-through, C - straight-through
A - straight-through, B - straight-through, C - crossover
A - rollover, B - straight-through, C - straight-through
15
After an unsuccessful ping to the local router, the technician decides to investigate the
router. The technician observes that the lights and fan on the router are not
operational. In which layer of the OSI model is the problem most likely occurring?
transport
network
-
8/14/2019 CCNA 2 Final V4.0 Answers
6/17
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
data link
physical
16
What are three characteristics of the TCP protocol? (Choose three.)
exchanges datagrams unreliably
is used to send IP error messages
forces the retransmission of unacknowledged packets
creates a virtual session between end-user applications
carries the IP address of the destination host in the TCP header
is responsible for breaking messages into segments and reassembling them at their
destination
17
Refer to the exhibit. The network shown is connected using services from the same
ISP. How will the Fohi router dynamically learn routes to the 192.168.16.16/28,192.168.16.32/28, and 192.168.16.64/28 subnetworks?
with BGP
with a static route
with a directly connected route
with an interior routing protocol
18
Refer to the exhibit. Which type of UTP cable should be used to connect Host A to
Switch1?
rollover
console
crossover
straight-through
-
8/14/2019 CCNA 2 Final V4.0 Answers
7/17
-
8/14/2019 CCNA 2 Final V4.0 Answers
8/17
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
How does a router know of paths to destination networks? (Choose two.)
inspection of the destination IP address in data packets
ARP requests from connected routers
manual configuration of routes
updates from other routers
DHCP information broadcasts
updates from the SMTP management information base
23
Refer to the exhibit. Which two statements describe the data conversation shown?
(Choose two.)
The data conversation was started by the HTTP application process running on the
client.
The data conversation is identified by TCP port 80 on the client.
The user started the data conversation by sending an e-mail.
The IP address of the Internet server is 192.168.17.43.
The Internet server will send data to port 8547 on the client.
24
What is one purpose of the TCP three-way handshake?
sending echo requests from the source to the destination host to establish the presence
of the destination
determining the IP address of the destination host in preparation for data transfer
requesting the destination to transfer a binary file to the source
synchronizing sequence numbers between source and destination in preparation for
data transfer
25
Which type of address is 192.168.17.111/28?
-
8/14/2019 CCNA 2 Final V4.0 Answers
9/17
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
host address
network address
broadcast address
multicast address
26
A customer reports connectivity problems to an ISP technician. Upon questioning the
customer, the technician discovers that all network applications are functioning except
for FTP. What should the technician suspect is the problem?
misconfigured firewall
bad port on switch or hub
misconfigured IP addressing on the customer's workstation
wrong DNS server configured on the customer's workstation
wrong default gateway configured on the customer's workstation
27
The show ip route command was executed on one of the routers shown in the graphic
and the following output was displayed:
C 192.168.4.0/24 is directly connected, Serial0/0
R 192.168.5.0/24 [120/1] via 192.168.4.2, 00:00:19, Serial0/0
R 192.168.1.0/24 [120/2] via 192.168.3.1, 00:00:20, Serial0/1
R 192.168.2.0/24 [120/2] via 192.168.3.1, 00:00:20, Serial0/1
C 192.168.3.0/24 is directly connected, Serial0/1
From which router was this command executed?
A
B
C
D
28Refer to the exhibit. Which two sets of commands are required to configure
-
8/14/2019 CCNA 2 Final V4.0 Answers
10/17
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
passwords for all management ports on a Catalyst 2960 switch? (Choose two.)
ALSwitch(config)# interface vlan 1
ALSwitch(config-if)# password ciscoALSwitch(config-if)# login
ALSwitch(config)# line vty 0 4
ALSwitch(config-line)# password cisco
ALSwitch(config-line)# login
ALSwitch(config)# line vty 0 15
ALSwitch(config-line)# password cisco
ALSwitch(config-line)# login
ALSwitch(config)# enable secret classALSwitch(config)# enable password cisco
ALSwitch(config)# interface fa0/1
ALSwitch(config-if)# password cisco
ALSwitch(config-if)# no shutdown
ALSwitch(config)# line cons 0
ALSwitch(config-line)# password cisco
ALSwitch(config-line)# login
29
A user reports being able to access the Internet but not being able to download e-mail
from the mail server at the ISP. What should the user check on the user workstation?
the POP3 and SMTP server settings in the e-mail application
the patch cable connections at the back of the workstation and at the wall plate
the DHCP settings in the operating system
the IP address, mask, and default gateway values
the NIC drivers
30
Refer to the graphic. Which command will configure a static route on Router A to
direct traffic from LAN A that is destined for LAN C?
RouterA(config)# ip route 192.168.4.0 255.255.255.0 192.168.5.2
RouterA(config)# ip route 192.168.4.0 255.255.255.0 192.168.3.2
-
8/14/2019 CCNA 2 Final V4.0 Answers
11/17
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
RouterA(config)# ip route 192.168.5.0 255.255.255.0 192.168.3.2
RouterA(config)# ip route 192.168.3.0 255.255.255.0 192.168.3.1
RouterA(config)# ip route 192.168.3.2 255.255.255.0 192.168.4.0
31
Which subnet masks could be used when subnetting a Class B IP address? (Choose
two.)
255.255.255.240
255.255.192.0
255.255.0.0
255.192.0.0
240.0.0.0
255.0.0.0
32
Refer to the exhibit. The network administrator has configured the RTA and RTB
interfaces. In order to allow hosts that are attached to RTA to reach the server that is
attached to RTB, a static route from RTA to the server LAN and a default route from
RTB back to RTA need to be configured. Which two commands will the
administrator use to accomplish these tasks on the two routers? (Choose two.)
RTA(config)# ip route 10.16.10.5 255.255.255.252 10.16.10.6
RTA(config)# ip route 0.0.0.0 0.0.0.0 10.16.10.6
RTA(config)# ip route 10.16.10.96 255.255.255.252 10.16.10.6
RTB(config)# ip route 10.16.10.6 255.255.255.248 10.16.10.6
RTB(config)# ip route 0.0.0.0 0.0.0.0 S0/0/1
RTB(config)# ip route 0.0.0.0 0.0.0.0 10.16.10.6
33How do port filtering and access lists help provide network security?
-
8/14/2019 CCNA 2 Final V4.0 Answers
12/17
-
8/14/2019 CCNA 2 Final V4.0 Answers
13/17
-
8/14/2019 CCNA 2 Final V4.0 Answers
14/17
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
access is required.
PAT uses unique source port numbers to distinguish between translations.
40
Refer to the exhibit. The graphic shows the output of a command issued on router
RTB. According to the output, what two statements are true of router RTB? (Choose
two.)
The router is connected to a router named Boise.
Router RTB is connected to a Cisco 1841 router.
Router RTB is directly connected to two other routers.
The IP address of the router interface connected to router RTB is 192.168.2.6.
The RTB router is connected to two Cisco devices by Fast Ethernet links.
41
Refer to the exhibit. The network administrator uses the command below to configure
a default route to the ISP network :
RTB(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.6
A ping issued from the ISP is successful to router RTB. However, ping echo request
packets arrive at a host that is attached to the Fa0/0 interface of RTB, and the replies
do not make it back to the ISP router. What will fix this problem?
The ISP must be configured to forward packets from the 192.168.1.0 network.
The ip route command needs to be edited so that the next hop address is 10.1.1.5.
The ip route command needs to be edited so that the 192.168.1.1 address is the nexthop address.
The ip route command should be removed from the RTB router configuration.
42
A network technician is using a network management station to gather data about the
performance of devices and links within the ISP. Which application layer protocol
makes this possible?
SNMP
-
8/14/2019 CCNA 2 Final V4.0 Answers
15/17
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
FTP
DHCP
SMTP
43
What are two purposes of DNS? (Choose two.)
to dynamically assign IP addressing information to network hosts
to simplify the administration of host and default gateway addressing on client
computers
to assign TCP port numbers to hosts as part of the data transfer process
to resolve human-readable domain names to numeric IP addresses
to replace the static HOSTS file with a more practical dynamic system
44
A hacker attempts to reach confidential information that is stored on a server inside
the corporate network. A network security solution inspects the entire packet,determines that it is a threat, and blocks the packet from entering the inside network.
Which security measure protected the network?
an IDS
an IPS
a host-based firewall
Anti-X software
45
How many host addresses may be assigned on each subnetwork when using the
130.68.0.0 network address with a subnet mask of 255.255.248.0?
30
256
2046
2048
-
8/14/2019 CCNA 2 Final V4.0 Answers
16/17
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
4094
4096
46
In an IPv4 environment, what information is used by the router to forward data
packets from one interface of a router to another?
destination network address
source network address
source MAC address
well known port destination address
47
A small tire retailer requires a low-cost WAN connection to its headquarters in order
to manage its inventory and process customer sales in real time. Which WAN
connection type is best suited to its needs?
Sonet
T3
dialup
DSL
leased line
48The command copy tftp running-config has been entered on the router. What will this
command do?
copy the configuration in RAM to a server
copy the configuration file from a server to RAM
copy the configuration file in NVRAM to RAM
copy the configuration file in NVRAM to a server
copy the configuration file from a server to NVRAM
-
8/14/2019 CCNA 2 Final V4.0 Answers
17/17
CCNA Discovery 4.1 - CCNA Discovery Answers
http://ccna-discovery-4.blogspot.com/
49
Refer to the exhibit. The network administrator needs to configure the Fa0/0 interfaceof RTB so that hosts from RTA can connect to the server that is attached to RTB.
Which two commands will the administrator use to accomplish this task? (Choose
two.)
RTB# ip address 192.168.102.98 255.255.255.248
RTB(config-if)# ip address 192.168.102.99 255.255.255.252
RTB(config)# ip address 192.168.102.97 255.255.255.252
RTB(config)# no shutdown
RTB(config-if)# no shutdown
RTB(config-if)# ip address 192.168.102.97 255.255.255.252
50
Refer to the exhibit. A NOC technician at an ISP enters the command shown. What
are two reasons to use this command? (Choose two.)
to map the path to 192.168.1.7
to test reachability to 192.168.1.7
to locate connectivity problems along the route to 192.168.1.7
to identify the ISPs that interconnect the NOC with the remote host with the address
192.168.1.7
to measure the time that packets take to reach 192.168.1.7 and return to the
technician's workstation