CB-HDR-87xx89xx DVR Quick Operating Instructions

19
Quick Operating Instructions v1.0 DVR Quick Operating Instructions Customer Service Hotline400-888 7918 Domain Name Access: Chinese Address: http://www.dvrserver.net:100 English Address: http://www.dvrserver.net:99 Cloud Service Address: http://www.vssweb.net Mobile Software: IOS, Android Mobile phone monitoring software name "IMSeye" 1

description

DVR Quick Operating InstructionsCustomer Service Hotline:400-888 7918Domain Name Access: Chinese Address: http://www.dvrserver.net:100English Address: http://www.dvrserver.net:99Cloud Service Address: http://www.vssweb.netMobile Software: IOS, Android Mobile phone monitoring software name "IMSeye"

Transcript of CB-HDR-87xx89xx DVR Quick Operating Instructions

  • Quick Operating Instructions v1.0

    DVR Quick Operating Instructions

    Customer Service Hotline400-888 7918

    Domain Name Access: Chinese Address: http://www.dvrserver.net:100

    English Address: http://www.dvrserver.net:99

    Cloud Service Address: http://www.vssweb.net

    Mobile Software: IOS, Android Mobile phone monitoring software

    name "IMSeye"

    1

  • Quick Operating Instructions v1.0 Thank you for choosing our embedded DVR product, please carefully read the following contents before you use the product: Precautions:

    The following contents describe the correct use method of the product as well as the measures to prevent danger or

    property loss, please be sure to observe the requirements.

    Please operate the DVR in the allowable temperature and humidity range.

    Do not install the DVR in damp, dusty or sooty locations.

    Please install the product horizontally and pay attention to preventing the product from falling.

    Install it in a well ventilated place, and do not block the vents of the product.

    Do not place any containers filled with liquids or other devices on the product.

    Do not disassemble the product randomly.

    Please choose the hard disk that is recommended by hard disk manufacturers and suitable for the embedded DVR.

    The real product shall prevail, and this instruction is for reference only.

    There may be technical inaccuracies or typographical errors in this product manual.

    The products or procedures described in this product manual may be subject to improvement or update at any time without further notice.

    The screenshots in this product manual are not those of the same model, for illustrative purpose only.

    If you have any questions or need the latest procedures and supplemental documentation, please contact the companys after-sale service department. Note: Full-featured DVR is taken as an example, serving as a reference for other models. I. Host Connection and Start

    1.1 Host internal SATA hard disk does not support hot plugging, please connect and fix the hard disk connecting line before starting the machine.

    1.2 Video output on DVR is connected to the video input interface of the monitor BNC (or the display VGA), turn on the monitor or the display.

    1.3 Connect the power supply to the power interface on the DVR, the device starts and enters into the system. II. System Login 2.1 Connect the mouse, click the right mouse button, select the main menu; the user login dialog box pops up. Select the user login (administrator user name: admin; Password: 123456; ordinary user: user; Password: 123456), the user password and user permission can be modified in the user administration, and it can also add new users. 2.2 The machine starts and automatically records. Under preview mode, users can click the right mouse button and select "Manual recording" for selection configuration.

    2

  • Quick Operating Instructions v1.0 2.3 The tree diagram of operation menu is as follows:

    Main menu

    Configuration management

    Maintenance management

    Peripheral management

    Storage management

    Turn off the device

    System setting

    Channel

    configuration

    Netw

    ork

    configuration

    Alarm

    configuration

    User

    administration

    Abnorm

    ality

    configuration

    Log information

    Online user

    Version Inform

    ation

    Restore default

    Stream statistics

    Autom

    atic m

    aintenance

    Output m

    ode

    PTZ configuration

    Alarm

    output

    Serial port configuration

    Autom

    atic polling

    confi guration

    Modify the channel nam

    e

    Output resolution

    Hard

    disk m

    ana gement

    Video backup

    User logoff

    Restart the device

    Turn off the device

    Channel setting

    Record plan

    Basic setting

    Netw

    ork state

    Advanced

    confi guration

    Dom

    ain name D

    DN

    S

    Netw

    ork transm

    ission

    Email

    PPPOE

    FTP

    IP ermission

    DV

    R SERV

    ER

    Local external alarm

    Video detection alarm

    Port modification

    UPN

    P

    Modify user passw

    ord

    Modify user perm

    issions

    Add or delete users

    Add or delete user group

    P2P

    Video inquiry

    3

  • Quick Operating Instructions v1.0 2.4 Record Plan Settings: Click the right mouse button "Main Menu" "Configuration Management" "Channel Configuration" "Record Plan", click the configuration to set. As shown below:

    [Channel] Select the channel number. The menu uses green, yellow and red to display the time plan of the three kinds of recording status: Regular, MD and Alarm of the corresponding channels within a week, which can be modified by clicking the [Configuration] corresponding to each date. [Copy] Copy the configuration to other channels. Click [Configuration] [Time Period] Set the recording time period, there are six time periods per day to choose from. [Regular] After selected, it is valid for regular recording. [MD] After selected, it is valid for MD recording. [Alarm] After selected, it is valid for alarm recording. III. Local Alarm Configuration

    3.1 Local alarm configuration: Click the right mouse button "Main Menu" "Configuration Management" "Alarm Configuration" , as shown below:

    4

  • Quick Operating Instructions v1.0

    [Alarm Input Channel No.] Select the alarm input channel. [Enable] Select Enable to control the ON and OFF of alarm input. [Type] Two selection modes: Normal Open and Normal Close. [Copy] Copy the configuration to other channels. [Processing] Click Processing and enter into the setting interface of alarm processing, the interface is shown in Figure 4-16. [Arming Time period] The menu will display the arming time, entering into the edit plan can configure the arming time of each day. [Linkage Set] Click Enable to start the linkage of [Recording Channel Linkage], [PTZ Linkage], [Polling] and [Capture], and select the linkage channels. [Processing] Click Enable to start the [Alarm Output], [Screen Prompt], [Send Email] and [Beep]. Alarm cancel delay time can be set as 10-300s. . Network Settings 4.1 Enter into the network configuration: Click the right mouse button Main Menu Configuration Management Network Configuration 1. To automatically get the IP address, tick the [automatically get the IP address], automatic search IP function (i.e.

    DHCP). When DHCP is opened, IP/Mask /Gateway cant be set. If current DHCP becomes effective, then the IP/Mask/Gateway displays that the value obtained by DHCP can be found in Network State.

    2. View the got IP address in Network State.

    5

  • Quick Operating Instructions v1.0

    3. After successfully getting the IP address, click Advanced DDNS to select DVR SERVER in DDNS Type

    column, tick Enable and click App. for confirmation. After about 1 minute, we will see that the ID column displays the exclusive ID number of the machine. Write down the ID.

    4. Enter into the settings of network transmission capacity, port and main playing, modify the port number of DVR, and

    the TCP, HTTP and port numbers range from 1 to 655,35. The way to use UPNP automatic forwarding port is as follows:

    4.1 Initiate the UPNP function of the router: take TP-link as an example: enter into the router Forwarding Rules Initiate UPNP Settings, as shown below:

    Note: The factory default ports of DVR include HTTP port 80 and TCP port 800. If there is more than one DVR under the same router, please modify the port of each DVR, in order to ensure that there is no repeated DVR port. Otherwise, it will forward with the last IP address of the same port number, i.e. the router will only map the last added IP address.

    . IE Access Method

    5.1 The IE controls are set in the following ways.

    5.1.1 Right click the browser icon , and click Attribute in the pop-up drop-down list to pop up the dialog box:

    6

  • Quick Operating Instructions v1.0

    Click the Security tab

    5.1.2 Set the seven items related to ActiveX as Enable or Prompt in the Security Settings interface, as shown below:

    7

  • Quick Operating Instructions v1.0

    5.2 Computer IE access is as follows:

    5.2.1 Taking the setting demonstration provided in the item 4 of Network Settings as an example: (note: For remote

    access of users, please subject to the parameters set by the users themselves) LAN access address: http://192.168.2.105:80 WAN access addresses: Chinese address: http://www.dvrserver.net:100 English address: http://www.dvrserver.net:99 In case of LAN access, enter the machines ID number into the pop-up input box, as shown below:

    Password: 123456 Ordinary User: user Password: 123456 Administrator User Name: admin

    Click to get IP, automatically go to the DVR login interface.

    Note: As to client access, please refer to the client access settings guidance document in the form of CD, it contains detailed software introduction and description.

    53 Cloud Service Access

    5.3.1 DVR host settings: Right click Main Menu Configuration Management Network Configuration Advanced to find out the VVNAT option, as shown below:

    The cloud service function will be initiated by default when the machine is started

    Enter into the VVNET option, as shown below:

    8

  • Quick Operating Instructions v1.0

    Bear this ID in mind, because it will be used in cloud service connection

    Description:

    1. Device ID: Cloud service connection ID number. Use this ID for connection in cloud service IE. Please bear this ID number in mind.

    2. The service password is the user password of the machine: The factory default is A0Yzk5 3. Note: The ID number of each device is different, so please refer to the ID number shown in the device;

    as to the password, please pay attention to the capital and small letters. 5.3.2 Enter the cloud service address http://www.vssweb.net into the IE address bar Enter into the cloud IE interface as shown below:

    Select Device login and enter the ID number in DVR Host Advanced VSS Cloud Service into the Serial number column

    The user password is the DVR host password: factory default: AD0h18 (the actual password shall be subject to that displayed by the machine)

    Description: 1. Enter the device ID number in the DVR into the Serial number column: such as ID number 0f004ca1 2. Password: factory default: please subject to that displayed by the machine (Both the factory default ID

    and password of each device are different; pay attention to the capital and small letters of the password) 3. After completing the input, click Login to enter into the monitoring interface. 4. User login: User can register an account to conduct centralized management for multiple devices. 5. When registering an account, it is required to fill in the E-mail in use to activate the account, otherwise

    9

  • Quick Operating Instructions v1.0

    the account can not be activated. Some electronic mailboxes may treat the activation mails as junk ones, so please find in the junk e-mails.

    5.3.3 Enter into the monitoring interface as shown below:

    Channel selection zone: Select the channel to be monitored, behind the channel, click the drop-down arrow to select the stream to be monitored . PTZ Control Zone

    . Color adjustment, other configurations . Split screen . Local recording, electronic magnification, capture, sound monitoring, monitoring turnoff . System configuration: remotely set the parameters of DVR, as shown below:

    10

  • Quick Operating Instructions v1.0

    1.4 Record Search: remote playback of record data and download, as shown below:

    . Select the record type . Select the start time and end time of the record playback. . Click Search and the search results will be displayed in the list (the maximum number of

    lists is 100). . Select the time period to be played and click Play to return to the monitoring interface for

    playing. green indicates that the current channel is remote playback;

    yellow indicates that the current channel is on-site monitoring.

    . Clicking Download can download the record data of the DVR host to the computer.

    11

  • Quick Operating Instructions v1.0

    54 CMS Connection

    5.4.1 After installing the CMS client, double click to open it

    5.4.2 Click Settings on the lower right corner after entering into the interface 5.4.3 Click Device Configuration 5.4 4 Click Add on the top left corner 5.4.5After clicking this option, modify the Login Type to P2P

    login 5.4.6 Device Name: Any

    Serial NO: enter the device ID (device ID in the P2P, such as 0f1008b6) Password: The control password in the P2P

    7. After saving, click the lower right corner to exit, and then click the Channel List on the top right corner and double click the

    Channel Connection.

    VI. Mobile Client Monitoring

    This section mainly describes the instructions for installation and use in Android and IOS phones.

    6.1 For IOS mobile software, please log in IOS official application search software IMSeye to download and install it. 6.2 Android can be installed by using the attached CD and copying it to computer, or searching IMSeye in Google

    Market. 6.3 It can also enter the https://play.google.com/store into the computer IE address bar to search IMSeye and download

    Android. 6.4 The Essential Conditions for Mobile Phones:

    6.4.1 IOS software must be Version 4.1 or newer, and support iPhone 3, iPhone 3S, iPhone 4, iPhone4S, iPhone5, iPAD 2, iPAD3 and iPAD 4.

    6.4.2 Android mobile phone software version: Android version 1.5 or newer.

    6.5 Main Functions: 6.5.1 Browse DVR monitor screen in real time, and support four-screen monitoring. 6.5.2 Support PTZ control (the front end should be controllable dome or PTZ) 6.5.3 Support mobile phone recording and local video playback. 6.5.4 Support mobile phone capture.

    6.6 Mobile Phone Monitoring Software Instructions Here take IOS software as an example; run this program and enter into the main interface: as shown below

    12

  • Quick Operating Instructions v1.0

    Icon Name Description

    Live View

    Enter into the Live View screen for PTZ control and other operations

    Device List Add or delete device list

    Photos Capture albums, view the captured photos

    Local Playback Mobile phone video search and playback

    About About software description

    2.1) To add new devices, enter into the interface as shown below:

    13

  • Quick Operating Instructions v1.0

    DeviceName: Device Name ConnectionaddressP2P Address: Please enter the device IP address or DDNS Command Port: Please enter the device data port number: default 8000 User Name: Enter the DVR user name Password: Please enter the user name password Max Channel: Please enter the maximum channel number of current device.

    7 Click Live View to enter into the program, as shown below

    Icon Name Description

    Password: 123456 User

    Factory default user name: admin LAN / DDNS input icon

    Password: 123456 Factory default user name: 0f038c18 P2P input icon

    14

  • Quick Operating Instructions v1.0

    Settings Button Enter into device management to modify, add or delete devices

    Alarm Prompt

    In case of alarm from current monitoring channel, send alarm prompt, and the icon becomes red.

    Recording Button

    Recording button, pressing this button can enter into the recording state

    Capture Button Capture channel images

    Play/Stop

    Play when there is no channel monitoring, and Stop when there is channel monitoring.

    Channel Display

    Switching Switching button for the number of display channels

    PTZ Control Click it to enter into PTZ Control.

    Add Monitoring Channel

    Double click this button to enter into device management and add monitoring channels

    Channel Selection Channel button, conduct channel switching in the single screen of

    the split screen

    8 Enter into the Device Management, as shown below:

    8.1 Double click the device, it will display the device channel

    8.2 Add new devices

    8.3 Delete devices

    9 PTZ Control Under monitoring, click PTZ Control, as shown below:

    15

  • Quick Operating Instructions v1.0

    : Up and Down, control the PTZ to move up and down

    : Left and Right, control the PTZ to rotate left and right

    Zoom in and Zoom out, control PTZ zoom

    Focusing increase and decrease

    : Aperture zoom in and zoom out

    Note: For mobile phone monitoring, QCIF and CIF monitoring are recommended

    Frame rate adopts 5-15 frame Stream adopts rated stream of 62-256.

    VII. Email Configuration Description

    7.1 Enter into theMain Menu-Configuration Management-Network Management-Advanced-Email,the

    configuration interface is shown as below:

    16

  • Quick Operating Instructions v1.0

    SMTP Server: It must be corresponding to the Email in use;

    Port: Email server communication port;

    User Name: Email name;

    Password: Email password;

    From: Email name;

    Title: Email title;

    Receiver: Target Email, maximum 3 receivers at present;

    SSL: SSL encryption Enable.

    Event Interval: The time interval between two Emails. (Default 5s)

    There are two types of Emails: One is text description, the other is picture description.

    InMain Menu-Configuration Management-Alarm Configuration, tick the function of Send Email in the

    Processing,

    In the Main Menu-Configuration Management-Alarm Configuration, initiate the Capture Enable under the

    corresponding alarm functions, it will send the Email containing picture, otherwise it will send the Email of text description;

    Common Email servers and ports:

    Yahoo: smtp.mail.yahoo.com 25 Regular Email sending;

    smtp.mail.yahoo.com 465 SSL encrypted Email sending;

    126: smtp.126.com 25 Regular Email sending;

    163: smtp.163.com 25 Regular Email sending;

    Gmail: smtp.gmail.com 465 (Only support SSL encrypted Email sending);

    The above types of Email are for reference only; for the servers and ports etc. corresponding to the other Emails, users may log

    in the corresponding Email system for inquiry.

    7.2. User name password error: Check whether the Email information is correct;

    17

  • Quick Operating Instructions v1.0

    7.3. Port error, for example: SSL Enable is initiated, but the port does not support. Therefore, be sure to check the port

    carefully;

    7.4. The recipient E-mail does not exist or has error;

    7.5. E-mail Enable is not initiated;

    7.6. Email server is busy, affecting Email sending.

    VIII. Common Troubleshooting

    The device can not be started or constantly restarted Possible causes: 1. DVR upgrade error, please remove the hard disk to restore the factory default. 2. DVR motherboard failure, please contact the supplier for repair. 3. Hard disk failure, please replace the hard disk. PTZ can not be controlled Possible causes: 1. RS-485 interfaces cable is connected incorrectly, A and B ports are reversely connected. 2. The settings of PTZ decoder type, protocol, baud rate and address bit are incorrect. 3. RS-485 bus connects too much PTZs, with signal reflex, it is necessary to connect in parallel with a resistor of 120

    remotely. 4. The RS-485 interface of the motherboard is damaged. The preview images of DVR are blurred Possible causes: The format of video input formats are not matched, if the camera is NTSC format, while the DVR adopts PAL format, then the preview images will be blurred. The playback images of DVR are blurred or no video is available Possible causes: 1. Program reading error, please try to restart the DVR. 2. Hard disk data error, please test the hard disk, and replace the hard disk if it is damaged. 3. DVR hardware failure, please contact the supplier. DVR can not be connected via network Possible cause: 1. Please check whether the physical network connection is normal. 2. Please check the DVR network parameter configuration. 3. Please check whether there is IP conflict within the network. The downloaded or backup video can not be played normally Possible causes: 1. The player is not installed correctly. 2. The backup U disk or mobile hard disk file system error. 3. No graphics acceleration software of version DX8.1 or newer is installed. Internet Explore Crash Possible causes: In case of IE browser crash during access, please close it and perform the following operations in Tool option.

    IE option

    Internet Explore 9.0 Accesses Possible causes: If using Internet Explore9.0 or newer versions for DVR access, please open the compatibility view mode, as shown below:

    18

  • Quick Operating Instructions v1.0

    IX. Hard Disk Calculation and Maintenance

    Hard Disk Capacity Calculation Reference

    If the DVR is initially installed, please first check whether the hard disk is installed. The capacity size of the hard disk itself DVR has no limit on the single hard disk capacity, please select according to the requirements of video saving time. Selection of the total capacity The computing formula of hard disk capacity: Total hard disk capacity (MB)=Number of channels required time (Hour) Occupied hard disk capacity per hour (MB/hour)

    Note: for the capacity of the hard disk purchased on market, 1GB=1000MB, not the theoretical 1GiB=1024MiB, therefore, in Hard Disk ManagementBasic Configuration, the displayed capacity is less than the nominal value of the actual hard disk. When DVR adopts the fixed-rate encoding mode, the estimations for the file size generated per hour are shown in the following table:

    Stream Size

    (Max bit rate) File Size

    Stream Size

    (Max bit rate)

    rate)

    File Size

    Stream Size

    (Max bit rate)

    rate)

    File Size

    96k 42M 320k 140M 896k 393M

    128k 56M 384k 168M 1.00M 450M

    160k 70M 448k 196M 1.25M 562M

    192k 84M 512k 225M 1.50M 675M

    224k 98M 640k 281M 1.75M 787M

    256k 112M 768k 337M 2.00M 900M

    Video file size When DVR adopts the variable-rate encoding mode, the file size generated per hour varies greatly, please refer to the actually generated video file size.

    * The CD contains detailed instructions for users reference.

    19

    DVR Quick Operating Instructions Customer Service Hotline400-888 7918 Domain Name Access: Chinese Address: http://www.dvrserver.net:100 English Address: http://www.dvrserver.net:99 Cloud Service Address: http://www.vssweb.net Mobile Software: IOS, Android Mobile phone monitoring software name "IMSeye" 53 Cloud Service Access

    54 CMS Connection VII. Email Configuration Description VIII. Common Troubleshooting IX. Hard Disk Calculation and Maintenance Hard Disk Capacity Calculation Reference